Operator’s Manual · 2016. 1. 15. · 4. The cup turret mechanism will index the first available cups to the dispense position. Fill the remaining empty cup stack with cups and
Post on 21-Apr-2021
1 Views
Preview:
Transcript
Part Number: PR14987000 Issue: Jan 2015
Operator’s Manual
ii VOCE Media
VOCE Media
Congratulations on your purchase of the VOCE Media freestanding vending machine from Crane Merchandising System.
Operator’s Manual iii
A FRESH APPROACH TO VENDING
EC Declaration of Conformity
We Crane Merchandising Systems (UK),
of Pipsmore Park, Bumpers Farm Industrial Estate, Chippenham, Wiltshire, UK, SN14 6NQ
Declare that:
Type of Equipment: Beverage Vending Machine
Model Name: VOCE Media
Has been designed and manufactured to comply with all essential requirements of the following
Regulations/Directives:
73/23/EEC ⇒93/68/EEC⇒ The Low Voltage Directive 2006/95/EEC and its amending directives 89/336/EEC ⇒ 91/263/EEC⇒ The Electromagnetic Compatibility Directive 92/31/EEC ⇒ 93/68/EEC ⇒ and its amending directives 2004/108/EEC REG. (EC) 1935/2004 on materials and articles intended to come into contact with food REG. (EC)
1895/2005 on the restriction of use of certain epoxy derivatives in materials and articles intended to come into contact with food DIR. 2002/72 EC relating to plastic materials and articles intended to come into contact with foodstuffs.
Tests have been performed by accredited certification bodies in accordance to the following specifications:
Low Voltage Directive: EN 60335-1: 2002 + A1+ A11, EN 60335-2-75: 2004+ A1
EN ISO 11201 + EN ISO 3744
EMC Directive: EN 55014-1:2000+A1+A2, EN 55014-2:1997+A1,
EN 61000-3-2: 2000+A2, EN 61000-3-3:1995+A1+A2,EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-11, EN 61000-4-2,
EN 50366:2003 +A1
HMM: Contribution of heavy metal migrants from different parts of the circuits of machine under in use conditions according to EU directives and guidelines.
With regard to hygiene for foodstuffs in location, the operator must comply with 852/2004/EEC which lays out the general and specific hygiene rules to ensure a high level of consumer protection with regard to food safety.
Date: 01 July 2014
Legal Representative Signature:
iv VOCE Media
VOCE Media
Co
nte
nts
Contents
Introduction ......................................................................................................... 1
Important Safeguards .......................................................................................... 2
Section 1 – Machine Specifications ..................................................................... 4
Section 2 – Installation ........................................................................................ 6
Section 3 - How to Vend a Drink ........................................................................ 10
Section 4 - Cleaning and Re-filling Procedures .................................................. 14
Section 5 - Service Keypad Functions ................................................................ 22
Section 6 - Programming Mode ......................................................................... 24
Section 7 – Operator’s Program ........................................................................ 26
Section 8 - Dispense Pipe Lengths ..................................................................... 35
Section 9 – Recommended Spare Parts ............................................................. 36
Section 10 - Error Messages and Simple Problem Solving ................................ 39
Section 11 - Decommissioning Your Machine ................................................... 42
Operator’s Manual 1
Intro
du
ction
/ Imp
ortan
t Safeguard
s
A FRESH APPROACH TO VENDING
Introduction This manual provides you with guidance on the installation, daily operation and basic programming of your VOCE Media vending machine. Crane Merchandising Systems always recommend that a trained technician service its equipment.
Crane Merchandising Systems are committed to continuous product improvement. This means that the information within this document, although correct at time of publication may be subject to change without prior notice.
The following Symbol is used throughout this Operator’s Manual:
Safety First! Take care, risk of personal injury.
Crane Merchandising Systems accepts no responsibility for damage caused to the equipment through misinterpretation or misuse of the information contained in this manual.
© Copyright 2012 Crane Merchandising Systems
2 VOCE Media
VOCE Media
Intro
du
ction
/ Imp
ortan
t Safeguard
s
Important Safeguards Always follow these basic safety precautions when operating or maintaining your machine:
1. Ensure that you and anyone who will operate or maintain your machine have this manual available for quick and easy reference and have read all instructions carefully before commencing work.
2. Beware of Electricity. Certain maintenance operations require your machine to remain connected and switched on. Only trained personnel should carry out these routines. Observation of safe working practices in accordance with current regulations is necessary at all times.
Important! Unless otherwise specified, always disconnect your machine from electricity supply before commencing work.
3. Do not operate your machine if any part is damaged until a service technician has carried out necessary repairs and ensured that it is safe.
4. Allow your machine to cool before handling or moving.
5. Never immerse your machine in water or any other liquid and never clean it using a water jet.
6. If your machine should freeze up, call a service technician before switching on.
7. Ensure that you are familiar with the most recent Health and Safety at Work Electricity at Work Regulations.
Operator’s Manual 3
A FRESH APPROACH TO VENDING
Intro
du
ction
/ Imp
ortan
t Safeguard
s
8. Access to the service area should only be permitted to persons having knowledge and practical experience of the appliance, in particular as far as safety and hygiene are concerned.
Important! This appliance is not intended for use by persons (including children under the age of 8 years and the infirm) with reduced physical, sensory or metal capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Your machine is for indoor use only and because it is a beverage vendor, should be sited in a clean and hygienic area.
4 VOCE Media
Section
1 – M
achin
e Specificatio
n
VOCE Media
Section 1 – Machine Specifications
1.1 External Features
1.1.1 General
1.1.2 Electrical Services
Height.................... 1830 mm Voltage .................. 220 - 240 Volts AC Width .................... 700 mm
Current .................. 13 Amp Fused
Depth .................... 785 mm
Frequency ............. 50/60 Hz
A-weighted sound pressure level is below 70dB Cup Capacity ......... 800* 7oz
*Approximate and are for guidance only.
1.1.3 Water Services
Pressure ................ 200 Kpa (2 Bar) - 600 Kpa (6 Bar) Stopcock ................ 15 mm BSP from rising main
All weights and dimensions are approximate and are for guidance only.
Operator’s Manual 5
Section
1 – M
achin
e Specificatio
n
A FRESH APPROACH TO VENDING
1.2 Internal Features
Key:
1 Main Switch 10 Kick Plate 2 Service keypad 11 Waste Bucket (liquids)
3 Cup Turret 12 Waste Bucket (solids)
4 Cup Dispense Unit 13 Dispense Head
5 Door Locking Mechanism 14 CoEx® Brewer
6 Cup Catcher 15 Oltre Brewer 7 SurevendTM Sensor 16 Mixer, Whipper System 8 Drip Tray 17 Ingredient Canisters 9 Drip Catcher
6 VOCE Media
Section
2–
Installatio
n
VOCE Media
Section 2 – Installation Important! It is essential that any other personnel responsible for installing and servicing your machine understand the following:
1. The installation and commissioning of your machine should only be carried out by a trained and authorised service engineer.
2. All water and electrical services must be correctly and safely connected in compliance with national and local regulations.
3. All covers must be replaced securely and the machine left in a safe condition.
2.1 Siting your Machine
1. Your machine is suitable for indoor use only. We recommend that it be situated in an area with an ambient temperature not below 10º C and not exceeding 30º C. Your machine should be located near the appropriate water and electrical.
2. Prior to placing your machine in its final location, ensure that there is sufficient access space available via passageways, stairs, lifts, etc.
3. To ensure adequate ventilation, 100 - 150 mm (4 - 6 inches) clearance must be allowed between the back of the cabinet and the wall.
4. Remove all transit packing, installation kit. Check for visual signs of damage which may have occurred during transit. If your machine is damaged or any parts are missing, you must contact the supplier immediately.
5. Level your machine by adjusting the feet.
6. Ensure that the door opens and closes easily.
2.2 Connecting the Water Supply
1. Your machine should be situated within 1 metre of a drinking water supply from a rising main, terminating with a stop-tap with 15mm outlet pipe.
N.B. The water supply should comply with national and regional regulations. (eg in the U.K. the Statutory Instrument No.1147 - “Water, England and Wales” and The Water Supply (Water Quality) Regulations 1989.
Dynamic water pressure at the stop-tap must be within the limits 2 - 6 Bar (200 Kpa - 600 Kpa).
2. Connect the flexi-hose (supplied with your machine) to the water supply. Flush the system thoroughly before connecting to the machine.
N.B. When connecting your machine to the water supply always use a new flexi-hose.
3. Ensure that the seal is correctly fitted. Ensure that all water supply fittings are tight.
4. Turn on the water supply at the stop tap and check for leaks.
Operator’s Manual 7
Section
2 – In
stallation
A FRESH APPROACH TO VENDING
2.3 Connecting the Electrical Supply
Safety First! Your machine must be earthed. The electrical safety of this appliance can only be guaranteed if it is correctly and efficiently earthed, in compliance with National and European regulations on electrical safety. Always ensure that the earthing is efficient. If you have any doubts, contact a qualified technician to check the system. On no account should it be earthed only to the water supply pipe.
The manufacturer declines all liability for damage resulting from a system which has not been earthed. On no account should it be earthed only to the water supply pipe.
The appliance must be connected to mains protected by a certified safety switch (double pole) with a capacity appropriate for the application and in compliance with National and European regulations on electrical safety.
The appliance must be connected to a 230 Volt 50Hz 13 amp fused switched socket outlet, installed to the latest edition of the IEE regulations, using a 3 pin BS approved 13 amp fused plug for UK and in compliance with National and European regulations on electrical safety in other countries
Important! If the mains lead becomes damaged in any way it must be replaced by a lead available from the manufacturer.
Important! If any internal fuses become damaged or fail in any way they must be replaced by a special fuse available from the manufacturer quoting the information written on the label adjacent to the relevant fuse-holder.
2.4 Commissioning Procedure
A trained installation engineer must carry out the following procedure before your machine is used for the first time. Ensure that the electrical and water services to the machine are connected correctly. Check for leaks in the water supply.
1. Open the door of your machine.
2. Ensure that the waste bucket is fitted correctly. Clip the level probe and overflow pipes to the rim of the bucket.
3. Cup Turret. Remove the lid and fill the tubes with the correct size cups for the cup catcher fitted to your machine. Allow the cups to drop into the tubes directly from the packaging. DO NOT touch the cups with your hands.
Important! Do not fill the tube directly above the cup dispense position. Allow the cup turret motor to rotate a full tube to the cup dispense position. Rotating the cup turret by hand will damage the mechanism.
Note! If you are using paper cups, first inspect each sleeve for damage to the cup rims. Damaged cups must not be used.
8 VOCE Media
Section
2 – In
stallation
VOCE Media
4. The cup turret mechanism will index the first available cups to the dispense position. Fill the remaining empty cup stack with cups and replace the lid.
5. Press the Cup Test button [7], on the Service Keypad and ensure that a cup is ejected cleanly from the cup drop unit.
6. All Models: The water inlet valve will open and the heater tank will start to fill. Ensure that no water overflows from the heater tank overflow pipe into the waste bucket. Check the system for leaks.
Note! The machine has a safety feature which will allow the heater tank to fill for a maximum of two minutes. If after power-up the heater tank has not filled within this time, the mains power supply should be switched off and then on again to reset the heater tank time-out.
Important! Should the machine fail to fill correctly or leak, turn off the water and power to the machine before investigating the fault.
7. All Models: Rotate soluble/freshbrew ingredient canister outlets to upright position. The bean canister needs to have the outlet slide in the closed position before removal.
Place the canister into the canister filling station located on the door and fill canister with the correct ingredient.
DO NOT place the canister on the floor or overfill with ingredient.
Refit canister into machine ensuring that it is returned to the correct position.
8. If fitted, check that the coin mechanism operates correctly. Fill the coin tubes. Ensure coin return mechanism functions correctly.
9. Operate the machine through its complete range of selections to ensure that each vend is correctly dispensed. Close the cabinet door. Ensure that the machine is left in a clean and safe condition.
Operator’s Manual 9
Section
2 – In
stallation
A FRESH APPROACH TO VENDING
2.5 Warranty Card
Please complete and return the warranty card that comes with the machine. Use the card to note any problems you encountered during installation, your feedback helps us to improve our products and services. Return the warranty card, whether problems were encountered or not.
10 VOCE Media
VOCE Media
Section
3–
Ho
w to
Ven
d a D
rink
Section 3 - How to Vend a Drink The VOCE Media freestanding drinks vendor features an interactive menu display. The intuitive full-colour LCD, with a direct selection touch-panel, makes it easy for the customer to produce a drink to their preferred taste and strength.
3.1 Selecting a Drink using the Direct Selection method
If the machine has not been used for 3 minutes it will display the idle screen. To enter the drink selection menu press any key on either side of the display.
Drink selections are made by pressing the corresponding key. The customer may then alter the drink strength and add milk/sugar to suit their personal preference.
The following example describes how to vend a Coffee selection from a machine set to ‘Free Vend’.
Select Coffee. The LCD will display the screen as shown. From this option screen you may adjust drink strength and add milk and/or sugar.
N.B. Each selection has a default strength setting that may be adjusted up or down.
To obtain a milder or stronger drink press the corresponding – or + key.
Operator’s Manual 11
A FRESH APPROACH TO VENDING
Section
3 – H
ow
to V
end
a Drin
k
If no further adjustment is required press the Start key to begin vending (see sub-section 3.3 Vending a Drink).
3.2 Adding Milk/Sugar
If milk is required select Milk. The screen updates and displays the menu as shown.
If more or less milk is required press the corresponding + or – key.
If sugar is required select Sugar. The screen updates and displays the menu as shown.
12 VOCE Media
VOCE Media
Section
3 – H
ow
to V
end
a Drin
k
If more or less sugar is required press the corresponding + or – key.
N.B. Certain drink selections do not allow milk or sugar to be added,
If no further adjustment is required, press the Start key to begin vending (see sub-section 3.3 Vending a Drink).
3.3 Vending a Drink
Once the required drink has been selected:
1. Press Start. Whilst the drink dispenses the screen displays the confirmation message as shown. At the bottom of this screen the number choice of the drink being vended is displayed.
For further information see sub-section 3.4 Selecting a Drink using the Number Choice Selection method.
N.B. Unless the customer has placed their own cup into the dispense area, a cup will be dispensed and the drink will be delivered into the cup.
Operator’s Manual 13
A FRESH APPROACH TO VENDING
Section
3 – H
ow
to V
end
a Drin
k
2. Once the drink has been dispensed the screen will display the message as shown. The drink can then be removed from the dispense area. The machine will beep once, and then return to standby mode.
3.4 Selecting a Drink using the Number Choice Selection method
When a drink is made to a customer’s preferred taste and strength using the Direct Selection method a number will be displayed which can then be entered in the Number Choice screen to obtain the same drink.
Press the Number Choice key.
When a valid number is entered the drink name and strengths, is displayed.
Press the Start key to begin vending.
14 VOCE Media
VOCE Media
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
Section 4 - Cleaning and Re-filling Procedures The quality of drinks produced by your machine can only be maintained if it is cleaned regularly following the schedule outlined. You will need to have the following available:
Bactericidal Cleaner
De-Staining Agent (as required)
CoEx Cleaning Tablets (as required)
Cleaning Cloths
Paper Towels
Small Brush
Two Large Buckets
Disposable Gloves (to be worn throughout these procedures)
4.1 Bactericidal Cleaner
This can either be a liquid or powder agent which should be dissolved in water in accordance with the instructions on the product packaging. The solution should be used for cleaning machine components and wiping surfaces during the cleaning operation.
4.2 De-Staining Agent
This is a liquid or powder agent which should be dissolved in water and diluted in accordance with the manufacturer’s instructions. The solution can be used on heavily soiled or stained components such as buckets and drip trays. Items or surfaces cleaned with this solution must be rinsed in clean water to remove traces of the cleaning agent.
4.3 Liquid Destainer - Brewer Units
Crane Merchandising Systems recommends that a liquid de-staining product is used for cleaning the paper/paperless brewer units fitted to freshbrew machines. The product must be used in accordance with the manufacturer’s instructions, following all health and safety guidelines.
4.4 CoEx Cleaning Tablets – CoEx Brewer Units
Crane Merchandising Systems recommends that the correct cleaning tablets are used for cleaning the CoEx brewer. The product must be used in accordance with the manufacturer’s instructions, following all health and safety guidelines.
4.5 Daily Cleaning & Filling Procedure
Important: It is necessary to carry out the cleaning and maintenance procedure outlined on the following pages on a regular basis.
Operator’s Manual 15
A FRESH APPROACH TO VENDING
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
4.5.1 Ingredient Canisters - Removal and Clean
1. Rotate canister outlets to upright position. Remove the ingredient canister and place in the filling station located on the door. DO NOT place them on the floor.
2. With a clean, damp sanitised cloth wipe the exterior of the canisters. Ensure canister outlets are dried thoroughly after cleaning.
4.5.2 Mixing and Steam Extraction System
1. Remove the dispense pipe from the mixing bowl. Rotate the steam trap to clear the extract housing and remove from the mixing system.
2. Remove the mixing system by turning the green locking lever to the left and pull the mixing system away from the back plate.
3. Pull off the impeller and the rubber seal.
4. Clean all of the mixing system parts, including the steam traps, mixing bowls and dispense pipes thoroughly in the diluted bactericidal cleaner solution. Rinse all components with clean water and dry thoroughly.
5. Remove the extract tray from the machine. Using a dry brush, clean the area under the extract tray.
6. Clean the extract tray. Dry and refit to the machine. Wipe the canister shelf and the upper interior of the machine with a clean, damp sanitised cloth.
7. Fill the canister with ingredient, ensuring that the canister outlet is in the upright position.
8. Remove the canister from the filling station and replace in the machine. Rotate the canister outlet into the mixing bowl.
16 VOCE Media
VOCE Media
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
9. Refit the mixing system. Push the rubber seal onto the motor shaft and ensure it is pushed fully home into the recess in the base.
10. The impeller has a mark on the front face and a corresponding pip on the reverse. Line these marks up with the flat on the motor shaft and click the impeller onto the shaft.
11. Line up the mixing system to the base unit, ensure that the green lever is turned to the left. Press the mixing system home on to the base unit and press and turn the green locking mechanism to the right to lock in place.
Ensure the mixing system is locked securely in position.
12. Refit the steam traps to the mixing systems, ensuring that the outlet lines up with the extract housing.
13. Press the securing tabs on each side of the dispense block and slide the block off the dispense head.
Clean thoroughly in the diluted bactericidal cleaner solution.
14. Rinse the dispense block with clean water and dry thoroughly before refitting to the machine.
15. Ensure pipes are refitted to their correct outlet position on the dispense block (see Section. 8 – Depense Pipe Lengths for details).
4.5.3.a Oltre Brewer Cleaning Procedure
Daily Cleaning Procedure
Important: Cleaning and maintenance must be completed daily.
Fill a cleaning bucket with hot water and dilute the bactericidal cleaner in accordance with the manufacturer’s instructions.
Open the door of the machine.
The brewer will always return to its fully open position at the end of the vend cycle. In the unlikely event that the brewer chamber is closed: -
Press ‘2’ on the service keypad, the brewer will start to move and will stop at the open position. Disassemble the brewer as illustrated:
Operator’s Manual 17
A FRESH APPROACH TO VENDING
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
Clean the Oltre brewer chassis and mounting area.
Clean all of the Oltre brewer components.
Rinse all components with clean water, dry then refit to machine.
Weekly Cleaning Procedure
Important: Cleaning and maintenance outlined on the following pages must be carried out on a weekly basis.
Check that the Oltre brewer(s) are in an open position, if not then press ‘2’ on the service keypad, the brewer will move and will stop at the open position
Remove the brewer chamber & filter belt assembly, then remove the belt. Clean all components with the recommended mix of de-staining solution; soak for 5 to 10 minutes.
Rinse all parts thoroughly in clean water & re-assemble into the machine.
Press the service keypad Brewer Clean button (4) and the machine will flush the brewer.
Empty the brewer waste container. Wash the waste container thoroughly.
N.B. If the feature has been turned on when the brewer waste container is emptied the waste counter must be reset. To reset the waste counter press button 12 on the service keypad, two audible bleeps confirm that the counter has been reset to zero.
18 VOCE Media
VOCE Media
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
4.5.3.b CoEx® B2C Brewer - Cleaning Procedure
4.5.3.b.1 Daily Cleaning Procedure
1. Remove the dispense pipe from the brewer outlet. Holding the unit as shown in the photograph, lift the green lever and carefully pull the brewer unit out of the machine.
Fill a cleaning bucket with hot water and dilute the bactericidal cleaning agent in accordance with the manufacturer’s instructions.
2. Carefully place the CoEx® brewer unit into the diluted bactericidal solution and clean the unit thoroughly. Ensure all coffee ground deposits are removed, paying particular attention to the area around the top of the piston and waste chute.
Remove the unit from the solution and rinse thoroughly with clean water. Dry the unit using a clean cloth.
3. Remove the B2C coffee chute assembly. Unscrew the two knurled thumbscrews and remove the coffee chute and coffee chute cover.
With a clean, dry brush clean the area around and under the coffee dispense outlets.
4. With a clean, dry brush wipe away any coffee deposits from both the coffee chute and cover mouldings.
Refit the coffee chute lid to the chute ensuring that the lugs on the cover fit securely into their mounting holes.
Refit the assembly to the machine and secure using the two knurled thumbscrews.
5. Refit the CoEx® brewer unit into the machine. Slide the unit into place until it ‘clicks’ into position. Refit the coffee dispense pipe to the brewer outlet as shown.
Operator’s Manual 19
A FRESH APPROACH TO VENDING
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
N.B. Depending how the machine has been setup the waste counter may need to be reset when the brewer waste container is emptied. This is done by pressing button [12] on the service keypad. Two audible bleeps confirm that the counter has been reset to zero.
4.5.3.b.2 Weekly Cleaning Procedure
The VOCE Media has a routine cleaning cycle for the CoEx® brewer, with a warning message to indicate a clean is recommended or required. If the ‘required’ message is ignored B2C and freshbrew drinks cannot be selected until the brewer is cleaned, using the following procedure:
Caution: Ensure that a suitable container is placed under the dispense position. Keep hands away from the dispense area and brewer whilst the cleaning cycle is in operation.
1. Press and release button [11] on the service keypad and follow the instructions on the main display. i.e. Press Start Sanitation After rinsing and cycling the brewer the screen will display the message ‘Please Place Cleaning Tablet in Brewer’.
Take one cleaning tablet (supplied in packs of 30 - CMS part no. ZC10598000) and place it into the brewer chamber as shown.
2. Press the Start Cleaning key on the drink selection screen
3. The cleaning cycle lasts approximately 5 minutes and dispenses approximately 9 cups of water through the dispense head. The LCD will display the message ‘Cleaning in Progress’ throughout the cleaning cycle.
4. When the cleaning cycle is complete the LCD will display the message ‘Cleaning Completed’. Press the Finish key on the drink selection screen to return the machine to standby mode.
20 VOCE Media
VOCE Media
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
4.6 Waste Buckets & Syrup Containers
1. Remove the waste water bucket from the machine. Empty and clean.
2. If fitted; check the syrup levels in the syrup containers and replace if necessary
3. Clean the base, sides and back of the machine.
Refit the waste water bucket into the machine. Ensure that the level detector and overflow pipes are located correctly in the bucket.
4.7 Dispense Area Components
1. Remove the cup catcher moulding.
2. Pull out the two spring loaded pins and remove the drip tray.
3. Clean the cup catcher, pipe, drip tray and grille. Wash the drip tray and grille thoroughly, rinse and dry.
4. Wipe clean the interior of the door and the dispense area.
5. Refit the drip tray, cup catcher and the cup stand, ensuring that the drip tube from the cup catcher moulding is located correctly.
6. Remove and discard the drip catcher cup and replace with a new cup.
Note: A 7oz cup should be used on all models.
4.8 Cup Check
1. Check the levels of the cups in the cup turret and where necessary, refill with correct sized cups.
Important! Allow the cups to drop into the tubes directly from the packaging. DO NOT touch the cups with your hands. Do not fill the tube directly above the cup dispense position. Allow the cup turret motor to rotate a full tube to the cup dispense position when the machine is powered up. Rotating the cup turret by hand will damage the mechanism.
Note: If paper cups are being loaded, each pack of cups must first be inspected for damage to the cup rims. Damaged cups must not be used.
2. Replace the lid.
Operator’s Manual 21
A FRESH APPROACH TO VENDING
Section
4 – C
leanin
g and
Re
-filling P
roced
ures
4.9 Cash Box
1. Wipe the inside of the coin mechanism with a cloth.
2. Remove coins from the cashbox and refit the cashbox to the machine.
3. Check the coin tubes and refill if required.
4.10 Test
Using the service keypad located in the rear of the door, proceed as follows:
1. Press the Cup Test button [7] and check that a cup is ejected correctly from the Cup drop unit.
2. Press the Park Head button [8] to ensure that the dispense head operates correctly and that the dispense pipes are fitted correctly.
3. Place a suitable container under the dispense head and press the Rinse/Flush button [3]. The machine will flush the system. Check that all of the mixing stations are water tight.
4. Press the Test Vend button [6] and using the selection buttons on the front of the machine, vend a drink to ensure that the machine operates correctly. Exit from the Test Vend menu.
5. If required press the View Counters button [5] and record the audit information.
22 VOCE Media
VOCE Media
Section
5 – Service K
eypad
Fun
ction
s
Section 5 - Service Keypad Functions Your machine is fitted with a service keypad mounted on the rear of the door. This keypad allows the operator to carry out specific functions for routine cleaning and maintenance.
N.B. During certain operations e.g. View Counters it is necessary for the operator to utilise the screen on the front of the door to access data.
The service keypad allows the operator to carry out the following functions:
5.1 Button 1 - Not used
5.2 Button 2 - Brewer Open (Oltre Brewer)
Opens the brewer/s. Brewer will move and stop at the open position.
5.3 Button 3 - Rinse/Flush
The flush sequence operates automatically and rinses the mixing bowls and brewers. Before the sequence begins, the system waits until the water in the heater tank is at the correct temperature. In order to guarantee the highest standards of cleanliness, the boiler fill valve is disabled, ensuring that the water used in the sequence is delivered at the optimum temperature to kill any micro-organisms. Each hot water valve and the corresponding whipper are switched on in sequence for a pre-set flush time.
Caution: Ensure that a suitable container is placed under the dispense position. Keep hands away from the dispense area whilst the flushing cycle is in operation.
5.4 Button 4 - Brewer Clean (Oltre Brewer)
Rinses the Oltre brewer/s.
5.5 Button 5 - View Counters
This button enables the operator to access the Data Recall Menu where the operator is able to view Non-Resettable and Resettable Sales Data, data relating to Timed Events, Identification Numbers of installed components and SureVend™ information.
5.6 Button 6 - Test Vend
This button enables the operator to vend a drink from the machine to ensure correct operation after cleaning or maintenance.
1. When the button is pressed a drink can be selected from the menu displayed.
2. Exit from the Test menu by pressing the Up one level key-pad.
5.7 Button 7 - Cup Test
This button enables the operator to test the operation of the cup drop unit. When the button is pressed the cup drop motor is operated and a cup is dispensed.
Operator’s Manual 23
A FRESH APPROACH TO VENDING
Section
5 – Service K
eypad
Fun
ction
s
5.8 Button 8 - Park Head
When this button is pressed, the dispense head moves to its fully extended position and stops.
Press the button again to return it to its homed position.
5.9 Button 9 - Boiler Fill (B2C Machines Only)
When pressed, the machine pumps a measured amount of water through the system (approximately 400ml). This button should be used to purge any water left in the system after the machine has been moved or shut down for any length of time.
5.10 Button 10 - Machine Cool Down (B2C Machines Only)
Important! This button enables an engineer to work safely on the water system and should not be used by the operator.
5.11 Button 11 - CoEx® Tablet Clean (B2C Machines Only)
When pressed, initiates the CoEx® brewer tablet cleaning routine. Crane
Merchandising Systems recommends that this brewer cleaning routine should be carried weekly.
5.12 Button 12 - Reset Waste Counter (F/Brew & B2C Machines Only)
When the waste container is emptied the counter must be reset.
When pressed the counter is reset, it is confirmed by pressing the OK button on the front screen
Note: Only relevant if the feature is enabled in the program (it is disabled by default)
5.13 Button 13 - Syrup Prime (Still/Carbonated Machines Only)
This button enables the operator to prime the syrup selections.
5.14 Button 14 - Not used
5.15 Button 15 - Start
When weighing ingredients within service mode this button has the same functions as START on the drink selection keys.
5.16 Button 16 - Not used
24 VOCE Media
VOCE Media
Section
6 – P
rogram
min
g Mo
de
Section 6 - Programming Mode
6.1 Programming Interface
Programming mode allows the operator to view and change options within the machine.
6.2 Navigating through the Menu Display
1. Once you have gained access to the programming mode (see sub-section 6.4 Accessing the Programming Mode), the LCD displays the Operator’s Main Menu.
2. A menu item is selected by pressing the corresponding key.
N.B. The bottom of the screen will often show important information. In many configuration menus it will display the current value for the selected item.
3. When a menu, sub-menu or data-display is split across multiple screens, the Next Page and Previous Page icons will be displayed.
4. To return to a previous menu screen, e.g. from the Diagnostics sub-menu up to the Main Menu, use the Up one level option.
6.3 Entering or Updating Parameters
To enter or update parameters, key in the actual digits of the number required using the keys 0-9. Once the correct parameter has been entered, press Save to overwrite the previous value and store the new parameter in the machines memory.
To return to the previous screen press the Up one level key.
Certain programming functions require that the operator choose either one or multiple parameters. These can take the form of either check boxes or radio buttons.
1. Select the required option, a filled radio button indicates that it is selected.
2. Using the keys, select the day on which the Sanitation Event is to take place, a TICK appears in its adjacent box indicating that it is selected.
Operator’s Manual 25
A FRESH APPROACH TO VENDING
Section
6 – P
rogram
min
g Mo
de
3. Continue until all required days have been selected.
6.4 Accessing the Programming Mode
1. Open the door of the machine. The LCD will automatically display the PIN entry screen; enter the 4 digit operator’s entry pin code and press OK.
N.B. The factory default operator’s code is 2-2-2-2.
2 You may be issued with alternative code.
26 VOCE Media
VOCE Media
Section
7 – O
perato
r’s Pro
gram
Section 7 – Operator’s Program Once in the Operator’s Program, the LCD on the front of the machine will display the Main Menu (illustrated below).
7.1 Data Recall
Entry into this menu allows the operator to view Non-Resettable and Resettable Sales Data, data relating to Events and SureVend™ assisted vend information. The Re-settable Sales Data and SureVend™ data menus contain an extra sub-menu which allows the operator to delete the current data.
7.1.1 Non Resettable Sales Data
This menu allows the operator to view monetary and sales values. This data cannot be reset and will remain intact for the service life of the controller board.
1. Select Non Resettable Sales Data (Overall Totals, By Product, Cash, Cashless or Token Vends).
2. Select Overall Totals. This menu displays both the total monetary amount and total vend counts for the following data:
Operator’s Manual 27
A FRESH APPROACH TO VENDING
Section
7 – O
perato
r’s Pro
gram
Data fields on the Overall Totals screen:
Sales-£ Displays the total machine sales in £ (NOT including Test Vends or Free Vends).
Sales-# Displays the total number of machine vends. This value includes normal, discount and surcharge vend totals. (NOT including Test Vends or Free Vends).
Discount-£ Displays the total monetary value of all discounts in £. Discount-# Displays the total number of discounted vends. Test Vend-£ Displays the total monetary value of all test vends in £. Test Vend-# Displays the total number of test vends. Surcharge-£ Displays the total monetary value of all surcharges in £. Surcharge-# Displays the total number of surcharge vends. Free Vend-£ Displays the total monetary value of all free vends in £. Free Vend-# Displays the total number of free vends. Total-£ Displays the total machine sales in £. Total-# Displays the total number of machine vends.
N.B. All sales data is presented in a format required by the latest European Vending Association Data Transfer Standard (EVA DTS).
3. The operator can also view and record audit data by individual product: Select By Product on the Non Resettable Sales Data menu screen. This menu contains all of the drink selections available from the machine.
4. Select the required product, e.g. Chocolate. The LCD will display the screen as shown below.
N.B. Individual By Product screens also display the price set for the selection as shown.
28 VOCE Media
VOCE Media
Section
7 – O
perato
r’s Pro
gram
5. Press Previous Page to return to the By Product menu screen. The operator can then view data for more selections and also access further menus via the Non Resettable Sales Data menu relating to Cash, Cashless and Token audit data.
7.1.2 Resettable Sales Data
This menu contains similar data to that available from the Non Resettable Sales Data menu.
However, once viewed data from this menu can be cleared from the machine memory.
1. Select Resettable Sales Data (Overall Totals, By Product, Cash, Cashless or Token Vends).
2. Select Overall Totals. This menu displays both the total £ amount and total vend count (since the last time it was cleared) for the data fields shown.
N.B. See sub-section 7.1 Data Recall for detailed descriptions of these data fields.
3. Once the operator has viewed required information from these submenus, the data can be deleted by pressing Reset then Yes to confirm. Press Previous Page to exit the menu without clearing the data.
4. The operator can also view resettable monetary and vend data for individual product by entering the By Product menu, and also view and record data relating to Cash, Cashless and Token Vends using their relevant sub-menus.
7.1.3 SureVend™
This menu allows the operator to view and reset data relating to the SureVend™ feature.
1. Select SureVend™ (Cup Drop Failures, SV Assisted, Clear Data). The LCD will display the screen as shown. From this menu screen the operator can view the number of cup drop failures that SureVend™ has logged and also the number of SureVend™ assisted vends.
2. The data can be cleared by pressing Clear Data then Yes to confirm.
Operator’s Manual 29
A FRESH APPROACH TO VENDING
Section
7 – O
perato
r’s Pro
gram
7.1.4 Mug Vends
This menu allows the operator to view the number of vends that the machine has made without dropping a cup.
1. Select Mug Vends.
2. The data can be cleared by pressing Clear Data then Yes to confirm.
7.1.5 Cup Vends
This menu allows the operator to view the number of vends that the machine has made using a cup from within the machine.
1. Select Data Recall / Cup Vends.
2. The data can be cleared by pressing Clear Data then Yes to confirm.
7.2 Diagnostic
This menu allows the operator to view any current errors on the machine.
7.3 Price Menu
This menu allows the operator to view and change individual prices, one price for all drink selections, set a discount to be applied for customers who use their own cup/mug and view the currently set highest and lowest prices.
N.B. Values entered via this menu are only applicable to machines fitted with a monetary system.
30 VOCE Media
VOCE Media
Section
7 – O
perato
r’s Pro
gram
7.3.1 Individual Prices
This menu allows the operator to view and set an individual price for each drink selection available from the machine.
1. All drink selections available from the machine are listed along with the current drink price. The example shown illustrates an Instant Coffee selection with a price set currently at 35p.
2. To change the price of the Instant Coffee, select Instant Coffee. The LCD will change and display the screen as shown below. To update the price, e.g. increase to 45p, press 4-5 using the appropriate keys.
3. Press Save. The new price is now displayed. The operator can then update further selections.
7.3.2 Entire Machine
This menu allows the operator to view and set a single price for all selections available from the machine.
Operator’s Manual 31
A FRESH APPROACH TO VENDING
Section
7 – O
perato
r’s Pro
gram
1. The LCD will display the screen, with the current value (e.g. 40p), as shown.
2. To update the value, e.g. set a price of 50p, press the sequence 5-0 using the appropriate keys.
3. Press Save to keep the changes and return to the Price menu screen. The new price is now displayed.
Tip: If most selections are to be sold at the same price, use this menu to quickly set the entire machine to this price, then access the Individual Prices menu to adjust prices for individual selections. Entering a single price for the entire machine will over-ride any individual prices previously programmed.
7.3.3 Mug Discount
This menu allows the operator to view and set a discount value against all drink selections for customers who use their own cup/mug.
When a customer places their own cup into the dispense area and selects a drink, the SureVend™ sensors will detect the cup and disable the cup drop mechanism. The value set for Mug Discount is then subtracted from the price of the drink selected and the appropriate change/credit returned to the customer.
N.B. It is important to ensure that any value entered for a mug discount is supported by the coin mechanism fitted to the machine, e.g. if a mug discount is set at 2p but the lowest coin available from the coin mechanism is 5p, the machine will not return the discount to the customer.
1. The LCD will display the screen, with the current value (e.g. 5p), as shown.
2. To update the value, e.g. set a price of 10p, press the sequence 1-0 using the appropriate keys.
3. Press Save to keep the changes and return to the Price menu screen. The new mug discount is now displayed.
7.3.4 View High/Low Price
This allows the operator to view the highest and lowest values in force, programmed via the Individual Prices sub menu.
N.B. If a single price is currently in force, this value will be displayed in both fields.
32 VOCE Media
VOCE Media
Section
7 – O
perato
r’s Pro
gram
7.4 Product Configuration Menu
This menu allows the operator to view and change Heater Tank Setup, Selection Timers, Custom Selection Names, Jug Vend Configuration, Disable Selections, Token Enabled, SureVend™, Cup Mechanism, Brewer Waste Management and Water Filter Management.
7.4.1 Custom Selection Names
This menu allows the operator to change the type of soup or flavour of cold drink displayed to the customer on the main menu.
The following example describes how to update the machine to display Tomato Soup instead of Soup.
1. Select Soup
2. Select Tomato Soup
3. Press Up one level
Note: the cold drink flavour is adjusted in the same way.
Operator’s Manual 33
A FRESH APPROACH TO VENDING
Section
7 – O
perato
r’s Pro
gram
7.4.2 Disable Selections
This menu allows the operator to disable individual drink selections.
The following example describes how to disable drink selections Instant Coffee, Espresso and Cappuccino.
1. Select Disable Selections.
2. Press the touch key adjacent to the drinks selections to be disabled, a TICK appears in its adjacent box indicating that it is now disabled.
3. Press Up One Level.
Note: On the standby screen any drink selections that have been disabled appear greyed out with the word “Unavailable” underneath and the key not illuminated.
7.4.3 SureVend™
This menu allows the operator to turn the SureVend™ product delivery feature on or off.
SureVend™ Overview
SureVend™ ensures that a cup is always available in the cup station before any money is collected or product delivered. The sensing system is a beam of infra-red light across the cup station that is broken by a cup as it falls into position from the cup drop unit, or by a customer placing his own mug in the dispense area.
The SureVend™ software monitors the cup station sensor during the time that the cup ring is operated. If a cup is not detected the software will then attempt to drop a cup a second and if necessary, a third time if a cup has still not been dispensed the main screen will display “Product Not Dispensed”.
Customers can now get their money back by pressing the coin return button or removing their card.
If this happens on three consecutive occasions the main screen will display the message “Please Insert Mug”. The machine remains in service but will not vend a cup from the cup drop unit.
To clear the message and return to standby mode open the door, if necessary, remove the damaged cup from the cup drop unit.
Ensure correct operation before leaving the machine.
To configure SureVend™ proceed as follows:
1. Select SureVend™.
2. Press the key adjacent to the required option.
3. Press Up one level.
N.B. By default SureVend™ is factory set to Enabled as indicated by the status line at the bottom of the screen.
34 VOCE Media
VOCE Media
Section
7 – O
perato
r’s Pro
gram
7.4.4 Free Vend
This menu allows the operator to enable/disable Free Vend when the machine is fitted with a coin/card system. When Free Vend is enabled, all available drinks selections will be dispensed at no cost. To enable Free Vend, proceed as follows:
1. Select Free Vend.
2. Select Enabled or Disabled as required.
3. Press Up One Level.
7.4.5 Leave Service Application
Enables the operator to return the machine to Standby Mode.
1. Select Leave Service Application.
Operator’s Manual 35
Section
8 – D
ispen
se Pip
e Length
s
A FRESH APPROACH TO VENDING
Section 8 - Dispense Pipe Lengths The VOCE Media machine uses three sizes of dispense pipe (as shown below) all of which can be replaced by the Operator:
Oltre brewer – 8mm x 13mm
CoEx brewer – 4mm x 8mm
All others – 6mm x 10mm
To replace pipes:
1. Open cabinet door and extend the delivery head by pressing 8 on the service keypad.
2. Using the above information about pipe size connect the pipes to the dispense head; the numbers on the diagram below indicate which mixing bowl/brewer should be connected to which nozzle.
3. The pipes should be cut to such lengths that when the head is in this extended position they are not too taut and neither does the pipe sag below the delivery head.
36 VOCE Media
Section
9 – R
ecom
men
ded
Spare P
arts
VOCE Media
Section 9 – Recommended Spare Parts The spares items listed on the following pages are available from your machine supplier and will ensure long and trouble free service from your machine.
9.1 Hygiene Kits
Operator’s Manual 37
A FRESH APPROACH TO VENDING
Section
9 – R
ecom
men
ded
Spare P
arts
Hyg
ien
e K
it -
(&
item
qu
anti
ty p
er
kit)
P
art
No
. - V
CH
HYG
(+
cod
e b
elo
w)
TFB
6
1
6
6
6 4
5
1.9
5M
3M
2
2
2
1
1
1
1
SFB
T
6 6
6
6 4
5
1.3
M
3M
1
1
1
1 1
SFC
6 6
6
6 4
5
1.3
M
3M
1
1
1 1 1
R&
G
6 6
6
6 4
5
1.3
M
3M
1
1
1
1 1
INST
AN
T
6 6
6
6 4
5
0.6
5M
3M
DFB
6
1
6
6
6 4
5
1.9
5M
3M
2
2
2
2
2
2
2
B2
CFB
T
6 6
6
6 4
5
1.3
M
3M
1
1
1
1 1
B2
C
6 6
6
6 4
5
0.6
5M
3M
Item
Wh
ipp
er
bo
wl,
sngl
e in
let
Wh
ipp
er
bo
wl,
du
al in
let
Str
eam
tra
p
Imp
ello
r
Sea
l
Ch
ute
, can
iste
r ce
ntr
al
Ch
ute
, LH
, lo
ng
Ch
ute
, RH
, lo
ng
Sili
con
e, p
ipe
8m
m x
12
.5m
m
Sili
con
e, p
ipe
6m
m x
9.5
mm
Cle
arin
g ri
bb
on
Ste
am t
rap
Olt
re
Mix
ing
bo
wl O
ltre
Sp
ou
t ID
4 t
ea
Sp
ou
t ID
6 c
off
ee
Tea
ch
amb
er a
ssy
73
mm
Co
ffee
ch
amb
er a
ssy
83
mm
Ref
No
.
1
2
3
4
5
6
7
8
Not Illustrated
38 VOCE Media
VOCE Media
Section
9 – R
ecom
men
ded
Spare P
arts
9.2 Dispense Area Components
Part No. Item Description
1 PL13126000 Cup Catcher Moulding - Squat Cup 2 PL13125000 Cup Catcher Moulding - Tall Cup
3 PL13128000 Cup Catcher Moulding - 12oz Cup 4 S101142960 Silicon pipe - 16mm OD
5 PL04589000 Cup stand
6 PL13802000 Drip tray 7 PL10274000 Grille - drip tray
8 MT14064290 Drip Catcher Bracket
1, 2, 3
4
5
6
7
8
Operator’s Manual 39
Section
10
– Error M
essages and
Simp
le Pro
blem
Solvin
g
A FRESH APPROACH TO VENDING
Section 10 - Error Messages and Simple Problem Solving
10.1 Error Messages
The table below lists the error messages that may be encountered and, where applicable, offers the operator solutions for curing them.
Safety First! Should the solution given not cure the problem, or the fault requires the assistance of a trained service engineer, DO NOT ATTEMPT TO CURE THE FAULT YOURSELF. Contact your machine supplier for assistance.
Error message Cause Solution
Co-Ex® Clean Recommended
Co-Ex® brewer has not been routinely cleaned
Perform a tablet clean (button 10) using the service keypad at earliest opportunity
Co-Ex® Clean Required The cleaning routine has not been followed & the Co-Ex® brewer disabled
Perform a tablet clean (button 10) using the service keypad immediately
Co-Ex® Setup Required Co-Ex® brewer has not been setup
Call an engineer, Freshbrew and B2C drinks cannot be dispensed
Out Of Cups Please Insert Mug
Cup stacks empty SureVend™ has detected an error with the cup drop unit
Refill cup stacks with correct size and type of cup Check the CDU, if error remains call engineer
Please Remove Cup A cup or mug has been left in the vend area
Remove the cup or mug to cancel the error
Sorr
y O
ut
of
Serv
ice
Mug Sensor Error Fault with mug sensor
Switch off the power and call an engineer
No IO Comm Communications fault
Brewer Not Homed Brewer has not returned to its home position
Brewer Jam Brewer mechanism faulty
Head Not Homed Dispense head has not returned to its home position
Head Not Extended Dispense head has not moved to its extended position
No Monetary Device The monetary device is not connected or has been configured incorrectly
Invalid Temperature The temperature device is disconnected or faulty
Water Tank Leak The dispense valve is leaking
40 VOCE Media
VOCE Media
Section
10
– Erro
r Messages an
d Sim
ple P
rob
lem So
lving
Error message Cause Solution So
rry
ou
t o
f se
rvic
e
Low Water The machine is filling Wait for the machine to fill with water
Fill Timeout The machine has failed to fill with water
Check that the water supply to the machine is connected and turned on
Water Tank Heating
The water is heating to the correct operating temperature
Wait for the machine to heat up and enter standby mode
Waste Bucket Full The waste bucket is full Empty, clean and refit the waste bucket
Rinsing Operator/engineer running the rinse program
Wait until machine completes rinse cycle and returns
Out of Coffee Fresh beans canister and/or freshbrew canister empty (B2C machines) Bean canister shut-off closed
Refill bean canister with fresh beans and/or coffee canister with freshbrew coffee Fully open bean canister shutoff
10.2 Simple Problem Solving
In the unlikely event of the machine developing a problem, details are given in the table below on how to deal with common faults that can be easily remedied by the operator.
Safety First! Should the remedy given below not cure the problem, or the fault is not listed, DO NOT ATTEMPT TO CURE THE FAULT YOURSELF. Contact your machine supplier for assistance.
Fault Possible Cause Remedy
Waste bucket overflowing
Level sensor incorrectly located in the bucket
Ensure sensor is positioned correctly in the bucket
Incorrect drinks dispensed
Ingredient canisters located incorrectly
Refit canisters into their correct positions
Leaking from dispense area
Mixing system/ʻOʼ ring fitted incorrectly
Refit correctly and ensure that all mixing stations are water tight
Blank LCD display Electricity supply turned off Ensure electricity supply is turned on at the mains
Cups jamming Incorrect cup size Remove cups from cup stack and replace with correct size cups
No change given from change giver (where fitted)
Coin tubes jamming Coin tubes empty or below pre-set level
Clear coin tubes and check for blockage Check and refill coin tubes where necessary
Low water indicated on LCD display
Water supply turned off Ensure water supply is turned on at stop tap
Operator’s Manual 41
A FRESH APPROACH TO VENDING
Section
10
– Error M
essages and
Simp
le Pro
blem
Solvin
g
Fault Possible Cause Remedy
Carbonated drinks not “fizzy”
CO2 gas bottle empty Check and if necessary replace
Paper fed brewer unit jamming
Incorrect paper fitted Filter paper loaded incorrectly Paper fouling on brewer guard
Remove and fit correct 90mm filter paper Reload paper and ensure that it feeds correctly Adjust brewer guard DO NOT REMOVE
Brewer wiper arms not removing coffee/tea waste. (Paperless freshbrew only)
Brewer chambers refitted incorrectly after cleaning
Refit brewer chambers ensuring that wiper lugs are located correctly
ʻSelection Not Availableʼ on LCD and machine will not vend coffee based drinks (B2C machines)
Waste counter has reached maximum number of vends dispensed through CoEx® brewer
Empty coffee waste bin and reset waste counter (see sub-section 5.12 for details)
10.3 Machine Leaking
Should the machine develop a leak, switch off the mains water supply at the stop-tap and if safe to do so, switch off the mains electricity supply.
Safety First! Do not attempt to repair the machine yourself.
42 VOCE Media
Section
11
– D
ecom
missio
nin
g
VOCE Media
Section 11 - Decommissioning Your Machine
1. Should the machine need to be shut down for short periods, for example over a long weekend, no special treatment is required. The machine should be thoroughly cleaned before the site is closed down and on return it is advisable to vend each drink type to ensure correct operation and to “freshen up” the machine.
2. If the machine is to be moved or transported, remove all ingredients and thoroughly clean the machine. Contact the supplier of the machine as only fully trained service engineers are authorised to carry out the decommissioning of a machine.
Operator’s Manual
A FRESH APPROACH TO VENDING
Visit the Tech Zone on our website to find this and other manuals
and technical information for the Crane range
www.cranems.co.uk/technical/
Pipsmore Park, Bumpers Farm Industrial Estate, Chippenham, Wiltshire, SN14 6NQ
Tel: +44 (0)1249 444807 Fax +44 (0)1249 444819 Email: sales@cranems.co.uk
Website: www.cranems.co.uk
CRANE MERCHANDISING SYSTEMS ®
top related