Operator’s Maintenance Manual - Boat Service Haarlem · 2014-10-23 · Operator’s Maintenance Manual CALIFORNIA – Proposition 65 Warning: Diesel engine exhaust and some of its
Post on 05-Apr-2020
6 Views
Preview:
Transcript
Operator’s Maintenance
Manual
CALIFORNIA – Proposition 65 Warning: Diesel engine exhaust and some of its constituents are known to the state of
California to cause cancer, birth defects and other reproductive harm.
Heat Exchanger Cooled Small Diesel Engine Range
BD1005, BV1305 and BV1505
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 1
Engine Details
Engine Type: Power: bhp Speed: rpm
BETA WOC NO: K Engine Serial No:
Gearbox Type: Serial No: Ratio :1
Purchased from:
Invoice No: Date:
Date Commissioned:
Specification / Special Details
IMPORTANT – Please fill in details at moment of purchase – it really will help you! (and it will really help us specify the correct spare parts for you).
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 2
1
INTRODUCTION 2Engine identification 2
Initial receipt of the engine 2
Engine storage 2
SAFETY PRECAUTIONS 3
TECHNICAL SPECIFICATIONS 4
SECTION 1: GUIDELINES FOR OPERATION OF ENGINE
Important checks prior to initial use 5
Initial start-up and bleeding the fuel system 5
Starting/stopping 6
SECTION 2: MAINTENANCE AND SERVICE GUIDELINES
Maintenance schedule: 7
Lubrication – checking and changing oil 8
Fuel system - pumps, filter, fuel/water separator 9
Cooling - fresh water system, keel cooling, heat exchanger 11
Sea water pump, heat exchanger 11
Belt tensioning 12
Air filter 13
Electrical 13
Laying up - winterising 13
Troubleshooting 15
Torque settings 25
SECTION 3: INSTALLATION GUIDELINES
Engine mounting 26
Alignment - drives, flanges, flexible drives 26
Exhausts & mounting exhausts 27
Fuel supply 28
Cooling - sea water inlet system 29
Calorifier system 30
Electrical and installations 31
Appendices –wiring diagrams and general arrangements 32
Component identification at rear of manual. 62
Maintenance record 65
Contents
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 3
OPERATION AND MAINTENANCE MANUAL FOR THE FOLLOWING BETA MARINE ENGINES BASED ON KUBOTA SUPER 5 SERIES
BD1005, BV1305, BV1505
2
ENGINE IDENTIFICATION
NOTE: In all communications withthe distributor or Beta Marine, theengine number, type, and W.O.C.number must be quoted.
BD1005, BV1305,BV1505
The engine serial number is stampedabove starter motor on the port sideof the engine, and is shown on therocker cover label.
INITIAL RECEIPT OF THE ENGINEA full inspection of the engine mustbe made immediately on delivery toconfirm that there is no damage. Ifthere is any damage then write thisclearly on the delivery note andinform your dealer or Beta Marinewithin 24 hours.
ENGINE STORAGEThe engine must be stored in a dry,frost free area and this is best done inits packing case. If storage is to bemore than six months then theengine must be inhibited (contactyour dealer or Beta Marine). Failureto inhibit the engine may result in theformation of rust in the injectionsystem and the engine bores, thiscould invalidate the warranty.
This manual has been compiled toprovide the user with importantinformation and recommendationsto ensure a trouble free andeconomical operation of theengine.
For further advice or technicalassistance, application should bemade to BETA MARINE LIMITEDor its distributors.
All information andrecommendations given in thispublication are based on the latestinformation available at the time ofpublication, and are subject toalteration at any time. Theinformation given is subject to thecompany’s current conditions ofTender and Sale, is for theassistance of users, and is basedupon results obtained from tests
carried out at the place ofmanufacture and in vessels usedfor development purposes. We donot guarantee the same results willbe obtained elsewhere underdifferent conditions.
SAMPLE
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 4
3
A Keep the engine, gearboxand surrounding area clean,including the area immediatelybelow the engine
B DRIVES - Power Take OffAreas
i) Gearbox Output Flange
The purpose of a marine dieselpropulsion engine is to providemotive power to propel a vessel.Accordingly the gearbox outputshaft rotates at between 280 and2400 rev/min. This flange isdesigned to be coupled to apropeller shaft by the installerand steps must be taken toensure adequate guarding.
ii) Forward End Drive
Engines are supplied withunguarded vee belt drives topower the fresh water pump andbattery charging alternator. Theinstaller must ensure that it is notpossible for injury to occur byallowing accessibility to this areaof the engine. The three pulleysrun at high speed and can causeinjury if personnel or clothingcome in contact with the belts orpulleys, when the engine isrunning.
iii) Power Take Off Shaft (Engine Mounted Option)
Shaft extensions are available asan option and rotate at between850 and 3600 rev/min. Ifcontact is made with this shaftwhen the engine is running,injury can occur.
C EXHAUST OUTLET
Diesel marine propulsion enginesemit exhaust gases at very hightemperatures - around 400-500°C. Engines are supplied witheither wet exhaust outlet (waterinjection bend) or dry outlet (dryexhaust stub) - see option list. At
the outlet next to the heatexchanger/header tank, theexhaust outlet can become veryhot and if touched, can injure.This must be lagged or avoided byensuring adequate guarding. It isthe responsibility of the installer tolag the exhaust system if a drysystem is used. Exhaust gasesare harmful if ingested, theinstaller must therefore ensure thatexhaust lines are lead overboardand that leakage in the vesseldoes not occur.
D FUEL
i) Fuel Lines
Diesel engines are equipped withhigh pressure fuel injectionpumps, if leakages occur, or ifpipes fracture, fuel at a highpressure can harm personnel.Skin must be thoroughly cleanedin the event of contact with dieselfuel.
ii) Fuel Supply Connections
Engines are supplied with 8 mmcompression fittings. Theinstaller must ensure that whenconnections are made, they areclean and free of leaks.
E OIL
The Beta propulsion is suppliedwith 2 dipsticks, one for theengine and one for the gearbox.Ensure dipsticks are returned andsecure after checking, if not oilleaks can cause infection whentouched. All oil must beremoved from the skin to preventinfection.
F SCALDING
An engine running under load willhave a closed circuit fresh watertemperature of 85° to 95°C. Thepressure cap on the top of theheat exchanger must not beremoved when the engine isrunning. It can only be removedwhen the engine is stopped andhas cooled down.
G TRANSPORTATION/LIFTING
Engines are supplied ontransportable pallets. Lifting eyeson engines are used for liftingengine and gearbox assemblyonly, not the pallet andassociated kit.
GENERAL DECLARATION
This machinery is not intended tobe put into service until it has beenincorporated into or with othermachinery. It is the responsibility ofthe purchaser/installer/owner, toensure that the machinery isproperly guarded and that allnecessary health and safetyrequirements, in accordance withthe laws of the relevant country, aremet before it is put into service.
Signed:
J A Growcoot, C.E.O, Beta Marine Limited
NOTE: Recreational Craft
Where applicable, thepurchaser/installer/owner and operatormust be responsible for making surethat the Recreational Craft Directive94/25/EC is complied with.
SAFETY PRECAUTIONS!
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 5
TEC
HN
ICA
L SP
EC
IFIC
ATIO
NS
Max
imum
Ang
le o
f Ins
talla
tion:
Trim
15°
, Rol
l 30°
(inte
rmitt
ent),
20°
cont
inuo
usR
otat
ion:
ANTI
CLO
CK O
N F
LYW
HEE
L, C
LOCK
WIS
E O
N O
UTP
UT
GEA
RBO
X FL
ANG
E FO
R U
SEW
ITH
RIG
HT
HAN
D P
RO
P IN
AH
EAD
, on
mec
hani
cal g
earb
oxes
. Hyd
raul
ic g
earb
oxes
can
be le
ft or
rig
ht h
ande
d.D
iese
l fue
l mus
t con
form
to B
S286
9-19
70 c
lass
A1
or A
2.
The
fuel
mus
t be
a di
still
ate
and
not a
res
idua
l oil
or b
lend
.Lu
bric
ant:
Engi
ne -
Engi
ne o
il m
ust m
eet M
IL-L
-210
4C (s
ee s
ectio
n 2
for d
etai
ls)
Gea
rbox
- se
e op
erat
or’s
man
ual f
or th
e ge
arbo
x oi
l typ
e an
d ca
paci
tyO
il pr
essu
re –
min
imum
(tic
kove
r) 0.
5 ba
rPo
wer
out
puts
: The
se c
ompl
y w
ith B
S EN
ISO
866
5:19
96 c
rank
shaf
t pow
erN
ote:
Dec
lare
d Po
wer
s to
ISO
8665
:199
51.
The
dec
lare
d po
wer
s ar
e at
the
sam
e en
gine
spe
ed a
s th
e IS
O 3
046
figur
es. T
his
spee
d is
the
spee
d re
late
d to
the
outp
uts
/ pow
ers
show
n.2.
Dec
lare
d po
wer
s ar
e at
the
gear
box
coup
ling
(cou
plin
g to
the
prop
elle
r sha
ft) a
s pe
r cla
use
3.2.
1 w
ith s
tand
ard
spec
ifica
tions
as
per o
ur c
urre
nt p
rice
lists
.Ad
ditio
nal a
cces
sorie
s or
alte
rnat
ive
gear
boxe
s m
ay a
ffect
the
decl
ared
pow
ers.
3. O
pera
tion
at p
aram
eter
s ou
tsid
e th
e te
st p
aram
eter
s m
ay a
ffect
the
outp
uts
/ pow
ers
whi
ch in
any
cas
e ar
e su
bjec
t to
the
ISO
tole
ranc
e ba
nds.
Stan
dard
En
gine
sB
D10
05B
V130
5 B
V 15
05
Cylin
der
34
4B
ore
(mm
) 76
7678
St
roke
(mm
) 73
.6
73.6
74.8
D
ispl
acem
ent (
cc)
1001
1335
1498
Com
bust
ion
Cool
ing
Star
ter
volta
ge (V
) St
arte
r ou
tput
(kW
)St
arte
r al
tern
ator
out
put (
Amps
) G
low
plu
g re
sist
ance
(eac
h)
Engi
ne s
peed
(RPM
) Po
wer
out
put t
o IS
O30
46 (B
HP)
28
.035
.037
.5D
ecla
red
pow
er IS
O86
65 (k
W)
19.2
25.7
27.1
Com
pres
sion
Rat
ioFu
el ti
min
g B
TDC
Capa
city
of s
tand
ard
sum
p ap
prox
(litr
es)
67.
57.
5Ca
paci
ty o
f sha
llow
sum
p ap
prox
(litr
es)
5 6.
5 6.
5N
ett d
ry w
eigh
t with
gea
rbox
(kg)
150
170
170
Fuel
Co
olan
t Co
olan
t cap
acity
app
rox
(H/E
litr
es)
5.5
77
Min
. rec
omm
ende
d ba
ttery
cap
acity
3 Vo
rtex
Wat
er12 1.
265
(sta
ndar
d)1Ω 22
:121
°
Die
sel f
uel o
il N
o.2D
33%
-50%
max
imum
ant
ifree
ze /
wat
er
12V
80Ah
(400
CCA
Min
)
4
3,60
0 3,
600
3,00
0
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 6
CAUTION
To avoid personal injury:• Do not bleed a hot engine as this
could cause fuel to spill onto a hotexhaust manifold creating a dangerof fire.
• Do not mix gasoline or alcoholwith diesel fuel. This mixture cancause an explosion.
• Do not get diesel on the flexiblemounts – they will deterioraterapidly if soaked in diesel.
• All fuel must be removed from skinto prevent infection.
5
SECTION 1GUIDELINES FOR OPERATION OF ENGINE
IMPORTANT CHECKS PRIORTO INITIAL USE
1. Generally, a new engine has theoil and anti-freeze removed afterthe works test. Fill the enginewith the correct oil and anti-freeze (see sections on ENGINEOIL and COOLING). Checkgearbox oil level - see separateoperator's hand book.
2. Ensure the engine is free to turnwithout obstructions.
3. Ensure battery is fully chargedand connected (the isolator is inthe 'ON' position).
4. Ensure Morse speed and gearboxcables are fitted correctly and thatcable travel lengths are correct.
Gear selection lever –allmechanical gearboxes: caremust be taken to ensure thatthe remote control cable isadjusted so that the selector leveron the gearbox moves FULLtravel and brought “hard up”against its end stop in bothdirections. Failure to achieve thecorrect adjustment will reduceefficiency of the clutch and maycause slippage at low revs.Warranty will not be accepted
on gearboxes returned in thewarranty period for failure dueto incorrect adjustment.
5. Ensure engine is out of gear with1/3 throttle - see single levercontrol instruction manual.
6. Open the fuel stopcock and bleedthe fuel water separator of air asshown in manufacturersliterature.
7. Fuel should now be at the fuel liftpump, see diagram 1a. Open thesea cock
INITIAL STARTUP ANDBLEEDING THE SYSTEM
(a) Open fuel bleed screw on fuelfilter assembly by 11/2 turns. Seediagrams 1a & 1b.
(b) Move hand priming lever on fuellift pump up and down until fuelwith no bubbles comes out of thebleed screw.
(c) Shut/tighten the bleed screw.Clean area thoroughly with tissuepaper.
(d) Continue to hand prime for 30seconds to push fuel through thefuel pump.
(e) Start engine (see normalstarting).
Note the engine may have to beturned over with the starter for afew seconds before it fires. Donot run the starter for more than20 seconds. If the engine has notstarted after 20 seconds thendisengage the starter andcontinue to hand prime for afurther 30 seconds, then repeat.
(f) If engine does not start after 3attempts then allow 5 minutesfor the starter to cool down beforerepeating (a) to (e).
Note: The starter windings can beburnt out with continuous cranking
Diagram 1a
Diagram 1b
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 7
6
STOPPINGEvery propulsion engine is fitted witha stop solenoid which is energised tostop. To stop engine simply pressstop push button, hold in until enginestops, then turn key from ‘RUN’ to‘OFF’ position.
When leaving the boat for anextended period,
• Turn off sea-cock (heat exchangercooled engines).
• Turn off battery isolator.
Do not turn the key to the offposition when the engine isrunning. This will damage thealternator.
*WARNINGDo not leave the key in ‘HEAT’position for more than 15 seconds -this will damage the heater plugsand eventually lead to poor starting.
Do not depress stop button for morethan 10 seconds as this will lead tooverheating and failure of thesolenoid.
The Super 5 range of engines areequipped with a mechanical stoplever in the event of electrical systemfailure. This lever is located on thestarboard side of the engine abovethe speed control lever. See Fig 2e:
Stop lever
Speed lever
NORMAL STARTING (BETAPANELS WITH SILVER KEYSWITCH,FOR KEYLESS SEE PAGE 23)
With the engine out of gear, set speedcontrol lever to 1/3 throttle. Turn key anti-clockwise to HEAT* (A) position and holdfor ten seconds, turn key clockwise toRUN (C) position. At this stage theinstrument panel should illuminate, analarm buzzer will sound and two (orthree*) red warning lights will illuminate:
STARTER BATTERY CHARGEDOMESTIC BATTERY CHARGE (D inbattery symbol - AB & C Deluxepanels only)*(Note: this will only illuminate if2nd alternator is fitted)
OIL PRESSURE and green POWER ON / RUN LIGHT(this will stay on)
Turn to START (D) position and enginewill motor, hold in position untilengine fires (see initial start-up sectionfor maximumtime starter canbe used).Release key(when enginehas started) toRUN position.Ensure alarmbuzzer is not sounding and thatwarning lights are extinguished. If oneor both of the alternator warning lights
are still on, then increase enginespeed to excite the alternator - thenreturn to idle. The battery chargelights should then go out. The runlight will remain on (green lamp).
Check for sea water flow. If no flowthen SWITCH OFF IMMEDIATELYAND CHECK SEA WATER SYSTEM.
Note: for some deluxe panel with theblack keyswitch, they operateclockwise as legend on panel (OFF –RUN – HEAT – START). Operation forengine start procedure is the same asstandard apart from this.
RUNC
STARTD
OFFB
HEATA
Fig. 2e
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 8
7
SECTION 2MAINTENANCE SCHEDULE
DAILY OR EVERY 8 HOURSRUNNING
• Check engine oil level.• Check gearbox oil level.• Check coolant level.• Check battery fluid.• Check drive belt tension• Ensure raw water inlet strainer is
clear.• Check stern gland lubrication.• Drain off any water in fuel water
separator.
AFTER THE FIRST 25 HOURSRUNNING
• Change gearbox lubricant (Seeseparate gearbox manual).
• Check that all external nuts,bolts and fastenings are tight.See table for torque values.Special attention should be paidto the flexible mount lock nuts,these should be checked fortightness, starting with lower nutfirst in each case. If the lowernuts are found to be very loose,then the alignment of the shaftto the gearbox half couplingshould be re-checked. Pooralignment due to loose flexiblemount nuts will cause excessivevibration and knocking.
• Check the belt tension on anysecond alternators fitted andadjust –see page 12.
• Check ball joint nyloc nuts fortightness on both gearbox andspeed control levers. Greaseboth fittings all over.
AFTER FIRST 50 HOURS
• Change engine lubricating oil.
• Change oil filter.
• Check for leaks on header tanktubestack. Tighten end cap boltif required.
• Drain off any water in fuel/waterseparator.
EVERY 150 HOURS
• If shallow sump (option) isfitted, change engine lubricatingoil and filter.
EVERY YEAR – OR EVERY 250HOURS IF SOONER
• Change engine lubricating oil(standard sump)
• Change lubricating oil filter • Check air cleaner element• Check sea water pump impeller
and change if worn.• Check wasting anode condition,
replace when necessary. Insome environments this may be6 montly or less.
• Remove heat exchanger tubestack, by undoing the bolt eachend of the tube stack. Removeend cover, pull out tube stackand clean. Replace rubber ‘O’rings and re-assemble.Immediately engine is startedcheck for leaks.
• Spray the key switch withWD40 or equivalent to lubricatethe barrel.
• Check that all external nuts,bolts and fastenings are tight.See table for torque values.
• Check ball joint nyloc nuts fortightness on both gearbox andspeed control levers. Greaseboth fittings all over.
EVERY 750 HOURS – As every250 hours plus the following:-
• Change air cleaner element.• Change fuel filter.• Change antifreeze.• Change gearbox oil.• Check electrical equipment,
condition of hoses and belts,replace as necessary.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 9
LUBRICATION
8
Engine oil: Engine oil should be MIL-L-2104C or have properties of APIclassification CC/CD/CE grades. Thefollowing table gives grades of oilrequired for various ambienttemperatures.
Note: A good quality 15W/40mineral or multigrade oil as used inmost diesel car engines will meetthese requirements. Do not use‘Turbo Diesel Oil’ or additives.
CHECKING ENGINE OILLEVEL
For quantities of oil required seesection marked ‘TechnicalSpecification’, Page 4When checking the engine oil level,do so before starting, or more thanfive minutes after stopping.
1. To check the oil level, draw outthe dipstick, wipe it clean, re-insert it, and draw it out again.Check to see that the oil level liesbetween the two notches.
2. If the level is too low, add new oilto the specified level - Do notoverfill.
IMPORTANT
When using an oil of different makeor viscosity from the previous one,drain old oil. Never mix two differenttypes of oil. Engine oil should bechanged after first 50 hours runningtime and then every year or every250 hours if sooner. Oil filter is acartridge type mounted on the portside of the engine.
(1) Run the engine for 10 minutes towarm up the oil.
(2) Your engine is provided with asump drain pump. Unscrew theend cap on the end of the pump,turn the tap to ‘on’. Use the handpump as shown to pump out theoil into a bucket. Turn the tap tooff position and replace end cap.See diagram 2c.
(3) Unscrew the oil filter and replacewith a new one. See diagram 2d.
Note: It is best to have a plasticbag wrapped round the filter tocatch any oil left in the system.(Always keep your bilges clean!)Before screwing in the new filterspread a thin film of oil round therubber gasket to ensure a goodseal and screw in – hand tight.
(4) Fill the engine with new oil asdescribed above.
(5) Run the engine and check for oilleaks
AMBIENT TEMP SINGLE GRADE MULTI GRADE
-30°C TO 00°°CC SAE 10W SAE 10W/30
-15°C TO +15°C SAE 20W SAE 15W/40
0°C TO +30°C SAE 30 SAE 15W/40
25°C AND ABOVE SAE 30 SAE 15W/40
CHANGING ENGINE OIL
Fig. 2d
Oil filter
Fig. 2b. Dip stickFig. 2a
Sump pump
Oil goesin here
End Cap
Fig. 2c
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 10
9
CHECKING GEARBOX OIL LEVEL
(1) The gearbox is fitted with a dip-stick and oil filler plug, see fig 2e.
(2) Each engine is supplied with agearbox operators manual whichspecifies the type of lubricatingoil to be used, the capacity andfrequency of changing of the oil.
(3) New engines are normallysupplied with the gearbox toppedup with lubricant but Check thelevel before starting the enginefor the first time.
(4) The oil can be changed via thedrain plug at the bottom of the
box or sucked out with a handpump via the filler plug.
(5) A guide to the type of oil to beused is as follows:
IMPORTANT
• Always fit a fuel/water separatorin the fuel supply system. Waterin the fuel can seriously damagethe injection system.
• If a fuel supply shutoff valve isfitted do not use a taper tap, onlyuse a ball valve tap. The ballvalve type are more reliable andless likely to let air into the fuelsystem.
• Be sure to use a strainer whenfilling the fuel tank. Dirt or sandin the fuel may cause trouble inthe fuel injection pump.
• Always use diesel fuel.
• Do not use kerosene, which isvery low in cetane rating, andadversely affects the engine.
• Be careful not to let the fuel tankbecome empty, or air can enterthe fuel system, necessitatingbleeding before next engine start.
• The fuel lift pump will only liftfuel through 0.25 metres. If thisis insufficient then an electric fuellift pump must be fitted. Drawing202-06421, illustrating thewiring of a typical electric fuel liftpump with ignition switchedrelay can be supplied uponrequest..
FUEL FILTER REPLACEMENT
1. The fuel filter is a spin on type.Remove by turning anti-clockwisewhen viewed from below.
2. Replace the fuel filter cartridgeevery 750 hours. See fig. 2g.
3. Apply fuel oil thinly over thegasket and tighten into position -hand tight.
4. Bleed as detailed - see initialstart up.
5. Check for leaks.
6. Do not get fuel on the flexiblemounts.
FUEL SYSTEM (see page 28 for a typical installation)
Fig. 2g
Gearbox Lubricant Capacity (approx)
TMC40M Use ATF Oil 0.2 litres
TMC60M Use ATF Oil 0.8 litres
PRM 80 Use Engine Oil 15W40 0.6 litres
PRM 120 Use Engine Oil 15W40 0.8 litres
PRM 150 Use Engine Oil 15W40 1.4 litres
PRM 260 Use Engine Oil 15W40 1.5 litres
ZF10M Use ATF Oil 0.35 litres
ZF15M Use ATF Oil 0.55 litres
TTMC 35A-2 Use Engine Oil 15W40 0.65 litres
Note: ATF is Automatic Transmission Fluid
Fig 2e
Dipstick
Oil drainplug
Oilfillerplug
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 11
10
COOLING
BD1005, BV1305 and BV1505engines are normally fresh watercooled. This water circulates throughthe engine and on to a heatexchanger where it is cooled by seawater which is pumped through thecooling tubes. The sea water is theninjected into the exhaust system (seediagram).
FILLING THE FRESHWATER SYSTEM
New engines are supplied with thefreshwater drained off. The followinginstructions must be followed to fillthe system.
(a) Mix up in a clean bucket a 33 to50% antifreeze to fresh watersolution. For the volume requiredsee technical specification page 4.
(b) Check that the drain tap or plugis turned off. (see fig 2l)
(c) Fill engine with freshwater/antifreeze solution through the top ofthe heat exchanger or headertank with the filler cap removed.(see fig 2m).
(d) Fill header tank to the top of thefiller neck and replace cap. Pressdown firmly on filler cap andhand tighten in a clockwisedirection.
(e) Run the engine for 5 minutes onno load (out of gear) and checkcoolant level. Top up asnecessary.
(f) Check system for leaks.
(g) If a calorifier is fitted care mustbe taken to see that this is alsofull of coolant and all the air isexpelled. (See calorifier fittingnotes under Section 3).
(h) Run the engine on one third loadfor 15 minutes, preferably withthe boat tied up. As the systemwarms up coolant may beexpelled from the overflow pipeinto the bilge. Stop the engineand allow the engine to cooldown before removing thepressure cap and top up thecoolant to one inch below thefiller neck.
Fig. 2mFig. 2l
DrainTap orplug
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 12
11
It is essential that a 33% to 50%anti-freeze/water mixture is used.This not only stops freezing up inwinter, but it prevents overheatingand corrosion.
The warranty is invalid unless thecorrect ratio is used.
Concentration of ethylene should notexceed 50%.
The anti-freeze in the fresh watersystem enables the boiling point ofwater to rise to 124°C with a 13 psipressure cap fitted. The water
temperature alarm switch willhowever be activated at 95° to100°C. If no anti-freeze or a veryweak solution is used, then the watertemperature switch may not beactivated before coolant is lost.
IMPORTANT
Removal of the pressure cap whenthe engine is hot can cause severeinjury from scalding hot water underpressure. Always allow the engine tocool and then use a large cloth whenturning the cap anti-clockwise to thestop. This allows the pressure to bereleased. Press firmly down on thecap and continue to turnanticlockwise to release the cap.
(i) Repeat (h) if coolant level is morethan one inch below the base ofthe filler neck when the enginehas cooled down.
(j) Run engine on 2/3 full load for 20minutes, check for leaks andrepeat (i).
(k) Anti-freeze solutions should bedrained off every 2 years andreplaced with a new solution.
Note: When draining fresh watersystem, ensure the engine has cooledsufficiently to prevent scalding fromhot pressurised water. Prior todraining a cold engine, remove thefiller cap from the header tank andthen open the water drain tap. Thisallows the water to drain freely fromthe system.
YACHTS AND LAUNCHES WITH HEAT EXCHANGER COOLING
SEA WATER PUMP AND COOLING SYSTEM
(HEAT EXCHANGER-COOLEDENGINES)
CAUTION
Before working on the sea watersystem ensure that the sea cock is inthe off position.
(1) It is very important that thecorrect sea water flow ismaintained to cool the closedcircuit system of the engine. Thekey component in this system isthe sea water pump impeller.This should be checked everyyear by removing the circularplate (see fig. 2h).
(2) Withdraw the rubber impellerfrom its drive shaft as shown.See diagram 2i.
(3) Check impeller for cracks in therubber, excessive wear or lostvanes. Replace with a newimpeller as necessary.
Note: If any pieces of rubberimpeller are missing then theymust be found as they are mostlikely to be trapped in theentrance to the heat exchangercooling stack. See ‘Cleaning TubeStack’. Fig. 2h
Fig. 2I
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 13
12
CLEANING THE HEAT EXCHANGER TUBE STACK AND REPLACING WASTING ZINC ANODE
(1) The wasting zinc anode shouldbe checked every six months andreplaced every year or asnecessary. The anode is attachedto the bolt inserted in the aft endcap of the heat exchanger. Seefig. 2j.
(2) Unscrew the bolt and replace thecomplete unit with a new one.
(3) Check for leaks.
(4) It is possible for fine sea weedand other debris to get past theinlet filter and into the tube stack.This should be removed andcleaned. See fig. 2k.
(5) Drain off coolant into a bucket.(6) Unscrew the 2 end cap retaining
bolts (one each end of the tubestack). Remove the ‘O’ rings and
pull out tube stack. Clean tubestack and end caps.
(7) Re-assemble using new ‘O’ rings.Do not overtighten end cap boltsand make sure the tube stack isthe right way round.
(8) Re-fill engine with water/anti-freeze solution and run engine upto temperature to check for leaks.
BELT TENSION
65 AMP ALTERNATOR (HEAT EXCHANGER COOLED)
100 AMP ALTERNATOR (OPTION)
Fig. 2j
ZincAnode
Fig. 2k
WARNING
Belt tension must only be checkedwith the engine switched off.
(1) On heat exchanger cooled enginesa single 65 amp is fitted asstandard. These alternators areadjusted as follows.
(2) The belt tension is adjusted byswinging the alternator outboardas it pivots on its power supportbolt.
(3) With the engine stopped, loosenthe support bolts and the linkadjusting bolt.
(4) Push alternator outboard totension and tighten link bolt.Check that the depression of thebelt at position shown isapproximately 1/2” or 12 mmwhen pushed down firmly bythumb. Tighten support bolts.
(5) Belt tension should be regularlychecked especially during thefirst 20 hours of running in anew belt, as stretchingoccurs.Belt tension must only bechecked with the engineswitched off.
Link adjust bolt
Support bolts
The same method, as outlined aboveapplies, but final tensioning must beby hand only. Over tensioning will
cause premature failure ofcomponents.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 14
13
AIR INTAKE FILTERThese engines are fitted with an air intake filter which should be checked every season and changed every 2 years orsooner if badly clogged. If badly clogged, check more often.
1 32
MAINTENANCE - ELECTRICAL
WARNING
Under no circumstances should thebattery be disconnected or switchedoff when the engine is running. Thiswill seriously damage the alternator
PANELS AND WIRING
See installation notes, page 31.
GENERAL MAINTENANCE
(1) The panel must be protected fromrain and sea water, see instal-lation. Sea water entering the keyswitch will eventually causecorrosion and could result in thestarter motor being permanentlyenergised and burning out. Spraykey switch every month with WD40 or equivalent.
(2) Check batteries for acid level andtop up if required. For lowmaintenance and ‘gel’ batteriessee manufacturers instructions.
(3) Loose spade terminalconnections are the mostcommon cause for electricalfaults - check on a regular bases(see maintenance instructions).
WINTERISING AND LAYING UP
HEAT EXCHANGER COOLEDENGINES LEFT AFLOAT ANDASHORE
(a) The engine oil and oil filtershould be changed at the end ofthe season rather than in thespring. See section 2.
(b) The closed circuit system shouldcontain a 50/50 solution of anti-freeze (this also applies to warmand tropical climates).
(c) For cold climates where the air orwater temperatures can fallbelow 3°C, the sea water circuitmust be protected in addition tothe fresh water system. This isbest achieved as follows:
(i) Close the inlet seacock to theengine (engine stopped).
(ii) Disconnect the sea waterinlet pipe and dip it into a smallbucket containing 50/50 anti-freeze solution.
(iii) Start the engine (out of gear)and run for 5 to 10 seconds untilthe anti-freeze is used up andcan be seen coming out of theexhaust outlet.
(iv) Shut engine off andreconnect the inlet pipe to theseacock.
The sea water or raw watercircuit is now protected by anti-freeze.
(d) Ensure instrument panel is wellprotected and give the key switcha spray of WD 40 or equivalent.
(e) With the engine stopped,disconnect the battery (alwaysdisconnect the negative cable firstand re-connect the negativecable last) and take it ashore fortrickle charging and top up asnecessary. If AC power isavailable then this can be doneon the boat.
(f) Fuel tanks should be kept fullduring the lay up period toeliminate water condensation inthe tank. Water entering the fuelinjection system can causeconsiderable damage.
LAYING UP ASHORE
(a) Change the engine oil before theboat is taken out of the water.
Warm engine oil is much easierto pump than cold!
(b) to (f) should be followed asabove.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 15
14
TROUBLE SHOOTINGBeta diesels are very reliable if installed and serviced correctly, but problems can occur and the following list gives themost common ones and their solution.
PROBLEM ENGINE DOES NOT START BUT STARTER MOTOR TURNS OVER OK
Possible Cause
No fuel:
Air in fuel system:
Water in fuel:
Blocked fuel pipe:
Fuel filter clogged:
Fuel lift pump blocked:
Blocked injector:
Fuel return not fed back to the tank:
Heater plugs not working:
Stop solenoid stuck in off position.
FUSE (If located by starter motor, usually it is positioned above flywheelhousing at rear of engine)
Note: For convenience, some engines are supplied with a spare fuse andholder attached onto the main engine fuse holder.
Solution
Turn fuel cock on and fill tank.
Vent air (see initial start-up)
Change fuel filter and bleed system.
Clean out and bleed system.
Change filter and bleed system.
Remove and replace.
Remove and clean.
Re-route fuel return pipe.
Check wiring to the plugs, and replace plugs if they are burnt out.
Check solenoid is free to return to run position.
PROBLEM: STARTER MOTOR WILL NOT TURN OR TURNS OVER VERY SLOWLY
Possible Cause
Battery discharged:
Starter motor flooded with sea water:
Wiring disconnected or loose:
Water in cylinders:
Engine harness fuse blown:
Solution
Charge battery or replace. Check alternator belt tension.
Remove and clean or replace.
Check circuit for loose connections.
Incorrect installation. This is serious - check engine oil for signs of water(creamy-coloured oil). Ring your dealer.
Replace fuse (located by starter motor or above flywheel housing) and checkfor wiring faults
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 16
PROBLEM: WHITE OR BLUE EXHAUST GAS
PROBLEM: BLACK EXHAUST GAS
Solution
Inspect and replace
Get the propeller re-pitched if necessary.
Inspect and clean if required
Possible Cause
Blocked air filter element:
Over pitched propeller - engine willnot reach its full rpm:
Accumulated debris on hull:
15
Possible Cause
Engine oil level too high:
Blocked injector:
Piston ring and bore worn, giving alow compression:
Check that the breather pipe is clearand not obstructed:
Solution
Reduce the level.
Service injectors.
Get compression checked by your dealer or Kubota service agent. He willadvise action to be taken.
Remove and clean out.
PROBLEM: ERRATIC RUNNING
Possible Cause
Air in fuel supply:
Fuel lift pump faulty:
Clogged fuel filter:
Fuel return not fed back to the fueltank, or blocked pipe:
Air filter blocked:
Worn or blocked injector:
Engine rpm in gear is too low, thismust be 850 min:
Faulty stop solenoid:
Broken fuel injection pump spring:
Solution
Check supply system for leaks and fix.
Replace.
Replace.
Re-route pipe or clean.
Replace.
Service injectors.
Increase engine tick over speed.
Disconnect wiring to solenoid. If running improves check for a wiring fault.
Replace.
PROBLEM: LOW POWER OUTPUT
Possible Cause
Propeller is too big:
Check gearbox reduction ratiorelative to propeller size:
Solution
Change or depitch.
Change.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 17
16
PROBLEM: LOW POWER OUTPUT
Possible Cause
Blocked fuel filter:
Blocked air filter:
Air in fuel system:
Governor spring incorrectly mounted:
Single lever control not operatingcorrectly:
The electrical load is too large on startup.
Solution
Replace.
Replace.
Check system.
Dealer to adjust.
Disconnect speed control cable and move the lever by hand. Adjust cable.
Disconnect or reduce the load.
PROBLEM: HIGH OIL CONSUMPTION
Oil leaks:
Piston rings worn:
Valve stem and guide worn:
Piston rings gap facing the samedirection:
Check for leaks.
Overhaul required.
Overhaul required.
Shift ring gap position.
Possible Cause Solution
Core plug pushed out due to frozenblock:
Water pump seal damaged:
Service Agent to check and replace.
Service Agent to check and replace.
Possible Cause Solution
PROBLEM: WATER IN LUBRICATING OIL - (Heat exchanger cooled)
Oil goes “milky” due to sea waterentering exhaust manifold:
Check installation - has anti-siphon valve been fitted? Change engine oil andrun engine for 10 minutes each time to eliminate any water. Get fuel injectionpump and compression checked by Service Agent.
Possible Cause Solution
PROBLEM: WATER IN LUBRICATING OIL - (Keel cooled)
Oil goes “milky” due to water enteringexhaust manifold and then into thesump:
Check installation – has dry exhaust system been fitted correctly, ensuring rainwater cannot enter the exhaust port and run back? (See DRY EXHAUSTSYSTEM) Change engine oil and run engine for 10 minutes each time toeliminate any water. Get fuel injection pump checked by Service Agent.
Possible Cause Solution
PROBLEM: WATER IN LUBRICATING OIL - (General)
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 18
17
PROBLEM: LOW OIL PRESSURE WARNING LIGHT COMES ON WHEN ENGINE SPEED REDUCED TO TICK OVER:
Faulty switch sender:
Engine running too hot:
Oil relief valve stuck partially openwith dirt:
Blocked oil filter:
Wiring fault:
Insufficient oil:
Replace.
Check cooling water flow (see section 2 Cooling).
Remove and clean.
Change.
Check circuit.
Top up and check for leaks.
Possible Cause Solution
PROBLEM: ENGINE OVERHEATS
Check coolant level:
Insufficient sea water flow:
Damaged or worn pump impeller:
Blocked tube stack in heatexchanger:
Zinc anode flakes blocking tube stack:
Pressure cap loose:
Switch sender faulty:
Inlet sea cock is too small:
High exhaust back pressure:
Air locks in cooling pipe work to keelcooler:
Keel cooler of insufficient size:
Possible Cause Solution
No W connection to alternator.
Wiring fault:
Check power output from ‘W’ connection. Should be about 9V AC.
Check circuit.
Possible Cause Solution
PROBLEM: PANEL REV COUNTER NOT WORKING (WHEN FITTED
Top up.
Clear blocked intake or filter.
Replace.
Remove tube stack and clean - replace ‘O’ rings.
Remove and clean tube stack as above.
Replace.
Replace.
Replace (see heat exchanger cooled seawater inlet system in section 3).
Must not exceed 3.1” of Hg.
Vent the system and top up coolant.
Contact boat builder.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 19
18
The most common cause ofoverheating is insufficient seawaterflow due to a blocked intake (weedor a plastic bag!). If this happensthen clear the blockage. If theproblem is not cured then check thesystem for sea water flow whichshould be 6.5 litres / minuteminimum at 1,000 rpm as follows:
(a) With the boat tied up and out ofgear run the engine up to 1000 rpm.*Hold a plastic bucket over the
exhaust outlet for 10 seconds andmeasure the amount of watercollected. Multiply this value by 6 togive the flow in litres/min. Repeattwice and take an average. If the flowrate is noticably less than the 6.5litre per minute minimum, then:
(b) Check impeller in sea waterpump - if worn replace.
(c) If impeller has a vane missingthen this will be lodged either in the
pipe to the heat exchanger or in theend of the exchanger. This must beremoved.
(d) Check flow again as in (a).
*Note: This operation must only bedone in safe conditions, in port andwith two assistants.
Working from a rubber dinghy isbest. The person holding the bucketshould take precautions againstbreathing in the exhaust gasses.
PROBLEM: KNOCKING NOISE
Propshaft touching gearbox outputcoupling through split boss or Type 16coupling:
Flexible mount stud touching enginebed:
Drive plate broken:
Engine touching engine bed:
Adjust, giving correct clearance (10mm) between gearbox and propeller shaft.
Adjust stud to clear.
Replace / repair.
Re-align engine / modify bed.
Possible Cause Solution
PROBLEM: BATTERY QUICKLY DISCHARGES
High load and insufficient running:
Low electrolyte level:
Fan belt slipping - black dust inengine compartment: Enginecompartment temperature too high:
Alternator defective:
Battery defective:
Poor wiring connection:
Reduce load or increase charging time. Large domestic battery banks subjectto high electrical loads will take a considerable time to recharge from a singlealternator.
Top up.
Adjust tension / replace belt with a high temperature and/or improve enginecompartment ventilation.
Check with Agent.
Replace.
Check wiring system.
Possible Cause Solution
GENERAL -HEAT EXCHANGE ONLY:
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 20
19
PROBLEM: MORSE CONTROL CABLE WILL NOT FIT
Fitting incorrectly Cables are being fitted the wrong way around, switch over and fit the oppositeway.
Possible Cause Solution
PROBLEM: VIBRATION
Poor alignment to shaft:
Flexible mounts not adjusted correctlyto take even weight:
Flexible mount rubber perished:
Loose securing nut on flexible mount:
Insufficient clearance between thepropeller tip and the bottom of theboat:
Loose zinc anode on the shaft:
Worn cutless bearing or shaft:
Weak engine support/bearers:
The alignment must be accurate even if a flexible coupling is used (see section3 ALIGNMENT).
Check relative compression of each mount.
Replace. (Diesel or oil will eventually perish most rubbers.)
Check alignment and then tighten the nuts.
There must be at least 10% tip clearance between propeller and bottom of theboat (ie 10% of the propeller diameter as clearance). Refer to boatbuilder.
Tighten or replace.
Replace.
Check for cracked or broken feet.
Possible Cause Solution
PROBLEM: TRANSMISSION NOISE
Check gearbox oil level:
“Singing” propeller:
Drive plate rattle at tickover:
Worn drive plate:
Propellor shaft hitting the gearboxhalf coupling:
Top up.
Check with supplier.
Check engine rpm (must be 850 rpm minimum in gear).
Change.
Move shaft back to give at least 5mm clearance (type 12/16 couplings only)
Possible Cause Solution
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 21
The following chart is compiled to aiddiagnosis of electrical faults, based onthe Beta 10-90hp range of engines. Ifyour engine was built before July2005, contact Beta Marine for therelevant electrical trouble shootingguide.
Standard sea specification engines(heat exchanger cooled) are suppliedwith a single alternator, mounted portside, supplying power to starter batteryand control panel.
Standard canal specification engines(keel cooled) are supplied with twinalternators:
• 1st alternator, mounted port side,supplying power to starter batteryand control panel
• 2nd alternator, the standardmounting position for this is abovethe engine on the starboard side(or below 1st alternator on 75 &90hp), supplying power to thedomestic battery system.
Both of these alternators workindependently, if the domestic batterysystem is disconnected, the enginewill still run correctly but:
• Domestic charge warning lampwill not function
• Warning buzzer will remain on atall times
Standard control panels are suppliedwith four or five lamps:
Four lamp panels:A, ABV, ABVW, B, these panels utilisebulbs inside sealed lamp holders
Five lamp panels:AB or Deluxe C, these panels alsoutilise bulbs inside sealed lampholders, having an additional lamp fordomestic battery charge
With keyswitch* in run position &engine off:
• Red lamp for no starter batterycharge should function
• Red lamp for no domestic batterycharge should function (Note: thiswill only function if a secondalternator is fitted to the engineand connected to a chargedbattery)
• Red lamp for high enginetemperature should not function(when engine is cold / cool /warm). This lamp will only everfunction if the engine is overtemperature.
• Red lamp for low oil pressureshould function
• Green lamp for panel power onshould function
• Buzzer should sound
* For operation of engines controlledwith keyless panels refer to ‘correctoperation of keyless panels’ later inthis section
When the engine is started, all the redwarning lamps should switch offleaving just the green power onindication lamp illuminated. The oilpressure lamp may take a fewseconds to switch off and the chargefail lamp may remain on until enginerpm is increased to approximately1,000rpm (if the engine was startedat tickover).
Before investigating any specificelectrical problem, always check:
• Connection between panelharness and panel loom. It mustbe clean, dry and secured with acable tie.
• Check the start battery isconnected to the correct terminalon the starter motor.
• Check the domestic battery is
switched on and connected to thecorrect terminals for the 2ndalternator.
• Battery connections, inspectingcondition of cables from battery toengine. If in doubt measure thevoltage at the engine.
• If alternator charge problem,measure battery voltage withengine off and again with enginerunning, if there is an increasealternator is functioning correctly, ifnot refer to check list.
Note: The two way plug on panelloom will only have a correspondingsocket to connect into from the engineif a 2nd alternator is fitted whichrequires this connection. Engines withonly one alternator do not utilise thisconnection.
20
ELECTRICAL FAULT FINDING & TROUBLE SHOOTING –ENGINES BUILT AFTER JULY 2005 ONLY
All Beta panels have the following warning lamps: (A, AB, ABV, ABVW, B and C Deluxe)
Starter battery charge warning lamp Red
• High engine temperature warning lamp Red
• Low engine oil pressure warning lamp Red
All panels also have:
• Panel power on (this is not a warning lamp) Green
In addition to above the domestic AB, C Deluxe panels also have a:
• Domestic battery charge warning lamp Red
Typical start battery positive
Typical start battery negative
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 22
21
PROBLEM POSSIBLE CAUSE & SOLUTION
No warning lamps or buzzer functioning, engine will not start or stop
• Battery isolation switch in off position –switch on• Starter battery discharged – charge• Engine fuse blown –check fuse (above starter motor or flywheel housing) &
replace if necessary. • Check for wiring faults.
Non function of warning lamp
THE WATER TEMPERATURE LAMPWILL NOT FUNCTION UNLESSENGINE IS OVERHEATING OR THEREIS A WIRING FAULT
• Disconnect switch wire to non-functioning lamp: green/blue –watertemperature, white/brown – oil pressure, brown/yellow –alternator charge.Reconnect wire temporarily to another warning lamp that is functioning; ifwire switches lamp on replace faulty lamp.
• Disconnect positive feed to non-functioning lamp. Reconnect temporarilywith wire from another warning lamp that is functioning, if wire switcheslamp on rewire with new connection.
• If none of the above, check continuity of connections from panel to engine.
Water temperature warning lamp on whenengine is not over temperature
(Not B or Deluxe C panel see table onfollowing page)
If engine is cold:
• Faulty wiring, check connection & continuity (small green / blue) from switchto panel lamp. Ensure this connection is not shorting to earth (ground).
• Faulty temperature switch –if lamp switches off on removal of connection toswitch unit, replace.
If engine is warm:
• Switch wire connected to large sender terminal of switch / sender unit.Remove and refit to smaller (switch) terminal
Buzzer not functioning
THE BUZZER WILL NOT SOUND FORGREEN POWER ON LAMP
• - If lamp is functioning but buzzer not sounding, check connection & continuityfrom illuminated warning lamp (red not green) to buzzer board.
• - Faulty warning panel buzzer board –replace.
Starter battery charge lamp not functioning
If tacho not functioning:• Alternator not connected properly, check continuity of small brown wire from
rear of alternator to ‘AC’ position on keyswitch.• alternator connected properly, faulty alternator –replaceIf tacho functioning correctly:• Check continuity of small brown/yellow wire from rear of alternator to no
charge warning lamp on rear of panel.• If alternator connected properly, faulty panel warning lamp –replace
Tacho not functioning
• -Check connections on rear of tacho, especially black/blue wire, terminal ‘4’• -Check connection of black/blue wire on rear of 1st alternator (W connection,
usually a bullet on flying lead, or lowest connection on alternators with 3 pincoupler)
• -Check continuity of black/blue wire from alternator to tacho• -Measure voltage from alternator W connection to earth (ground), should be
approx. 7.5 – 9.0 volts AC
Domestic charge lamp not functioning,buzzer remains on with engine running
• Domestic battery not connected• Domestic battery not connected correctly:B+ to domestic isolation block on starboard rail (port on 75 & 95hp)B- to engine earth (ground)• Domestic battery flat• Panel relay faulty / incorrectly wired:Check voltage at relay terminal 86, white wire is positive feed for warning lampfrom AC position of keyswitch.
Domestic charge lamp not functioning,buzzer switching off with engine running
THIS LAMP WILL NOT FUNCTION IF ASINGLE ALTERNATOR IS FITTED
• No second alternator fitted to engine, domestic lamp not used• D+ (charge indication) lamp connection at rear of alternator not connected• Two way plug & socket disconnected between engine harness & panel loom
ELECTRICAL FAULT FINDING – ALL LAMP PANELS
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 23
22
PROBLEM POSSIBLE CAUSE & SOLUTION
Oil pressure warning lamp not functioning,oil pressure gauge showing maximumdeflection. Engine off and keyswitch in runposition
• Faulty wiring –check wire connection & continuity (small white/brown) fromsender to panel lamp. Ensure this connection is not shorting to earth (ground).
Oil pressure gauge showing no movement -even when engine is started. Warning lampfunctioning correctly
• Faulty wiring –check oil pressure sender wire (small white / brown) is connected.
Oil pressure showing no movement,Warning lamp not functioning correctly
• Check connection to oil pressure gauge, if plug is not connected to socket on rear ofgauge reconnect.
• If all connections are correctly made, possible faulty sender unit –check resistance toearth (ground) approx. 50Ω. Replace if no reading or short-circuited.
• If adjusted correctly & buzzer still sounding, possible faulty switch gauge unit –replace.
Oil pressure showing normal operatingpressure (0.75–5 bar). Buzzer sounding &lamp illuminated.
Engine warm:
• Incorrectly calibrated switching point for warning lamp, adjust on rear of gauge to0.5 bar (minimum adjustment on gauge).
• If adjusted correctly & buzzer still sounding, faulty switch gauge unit – replace.
Water temperature gauge showing 120°C / 250°F
THIS ALSO APPLIES TO THE B PANELWITH MURPHY GAUGE
Engine cold / cool:
• Faulty wiring, check water temperature sender wire is not shorting to earth(ground)
• Faulty sender unit, –check resistance to earth, approx. 3.5kΩ (cold) – 0.5kΩ(warm). Replace if notably less.
Water temperature gauge showing normaloperating temperature (85°C). Buzzersounding & lamp illuminated.
THIS ALSO APPLIES TO THE B PANELWITH MURPHY GAUGE
Engine warm:
• Incorrectly calibrated switching point for warning lamp, adjust on rear of gauge to100°C/210°F.
• If adjusted correctly & buzzer still sounding, faulty switch gauge unit – replace.
Water temperature gauge showing nomovement, lamp not illuminated, enginewarm.
THIS ALSO APPLIES TO THE B PANELWITH MURPHY GAUGE
• Check connection to sender, if disconnected gauge will not function.• Check connection to temperature gauge, if plug is not connected to socket on
rear of gauge reconnect. • If all connections are correctly made, faulty sender unit –check resistance to
earth, approx. 3.5kΩ (cold) – 0.5kΩ (warm). Replace if no reading.
ELECTRICAL FAULT FINDING – DELUXE C & WATER TEMPERATURE FUNCTION ON B PANELSIn addition to the fault finding detailed on the previous table, the following is specific for the C deluxe panel (Alsoapplicable for the B panel with Murphy water temperature gauge)
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 24
23
ELECTRICAL FAULT FINDING –NON BETA PANELS
Engines can be supplied wired up tosuit VDO switch senders, usuallyfitted to a non-Beta control panel.
If so refer to our wiring diagram 200-60971/01 (also part number forreplacement harness)
• Loom is configured differently inthe 11-way plug toaccommodate the extra wiring.
• Small brown wire (batterysensed alternator feed) fitted withbullet connection beside harnessplug.
• Oil pressure & water temperatureswitch / senders fitted to engine,requiring individual connectionsfor driving gauges & warninglamps.
Note: Water temperature switch / sender (Part number 200-01133)
• large spade is sender connection (green / blue)
• small spade is switch connection (blue / yellow)
Oil pressure switch / sender (Part number 200-62680)
• G Gauge wire (white / brown)
• M Earth (black)
• WK Warning lamp (green / yellow)
ELECTRICAL FAULT FINDING –EXTENSION HARNESSESSome installations require one of thepanel extensions 11 way connectorsto be removed to allow the cable tobe passed through bulkheads etc. Ifany panel problems are experiencedafter this may have been carried out,visually check all 11 way connectionson engine harness to panel extension
(and panel extension to panel onDeluxe C) to ensure wire colours toeach terminal match up to the correctcolour in its corresponding terminal.Extra attention must be given to black(ground) and black/blue (tacho), alsobrown (switched positive to alternator)and brown/yellow (charge fail) as
these connections are harder todistinguish between in poorly litareas. Whilst doing this checkintegrity of each connection to ensureterminals have not becomedamaged. Once checked, re-fit cabletie around each connection to keepthem secure.
ELECTRICAL – CORRECT OPERATION OF KEYLESS PANELS
These panels control the engine withthree water resistant push buttonsinstead of a keyswitch, which are lessprone to damage and corrosion fromsea water spray than a keyswitch.To operate the engine:1. Press and hold ‘HEAT’ button for
ten seconds maximum• Red lamp for no starter battery
charge should function• Red lamp for high engine
temperature should not function(when engine is cold / cool /warm). This lamp will only everfunction if the engine is overtemperature.
• Red lamp for low oil pressureshould function
• Green lamp for panel power onshould function
• Buzzer should sound2. Press ‘START’ button and hold in
position until engine fires (seeinitial start-up section formaximum time starter can beoperated). Release button (whenengine has started)
• All red warning lamps shouldextinguish and buzzer should stopsounding. The oil pressure lampmay take a few seconds to switchoff and the charge fail lamp mayremain on until engine rpm isincreased to approximately1,000rpm if the engine wasstarted at tickover.
• Green lamp for panel power onshould still function
3. To stop the engine press the‘STOP’ push button, hold in untilengine stops. This button alsoswitches the power off to thegauges, engine and power onlamp.
4. To re-start the engine, simplyrepeat steps from ‘1’ above, thereis not need to switch batteryisolators off whilst remaining onboard.
5. If leaving the boat, isolate startbattery from engine and panel, toprevent accidental start up ofengine.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 25
24
BETA P/N’S FOR REPLACEMENT ITEMS:
Description Part number
40 amp blade fuse (all panels) 200-00959
Alarm board –all panels from June 05 200-04655
Oil pressure switch 1/8” BSP (not C panels) 600-62670
Oil pressure sender (C panels only) 200-94350
Oil pressure switch gauge (C panels only) 200-96190
Temperature switch with single terminal (on some BZ602 & BD902) 600-62820
Temperature switch / sender 1/8”BSP (not B or C panels) 200-01133
Temperature sender (B & C panels only) 200-94360
Water temperature switch gauge (B & C panels only) 200-96200
Voltmeter (C panels only) 200-96210
28Ra relay 12V 40A (fitted to rear of domestic panels) 200-87020
Keyswitch, silver bezel 600-00057
Panel stop button (all panels) –Also heat and start on ABVW 200-00072
Tacho, 0-4000rpm with digital hour counter (all panels but A) 200-02373
Standard engine harness Mini Series 200-98380/01
Standard engine harness S5 Series 200-60973/05
Standard engine harness S3 series 200-05267
Iskra 65 amp sub loom 200-01196
1m panel extension loom 200-04588/01
2m panel extension loom 200-04588/02
3m panel extension loom 200-04588/03
4m panel extension loom 200-04588/04
Domestic charge engine sub loom (top mounted alternators) 200-01197
Green power on indicator lamp & retaining clip 200-04656
Red warning indicator lamp & retaining clip 200-04657
Note: the above part numbers aresuitable for earth return installationsonly (where battery negative cable isconnected directly to engine ground).For insulated earth (where batterynegative cable is isolated from engineground) different harnesses,
alternators, switches for oil pressureand engine temperature will berequired. If your application is wiredas insulated earth return and theengine will not operate correctly,always check starter battery negativeis connected to the correct terminal
on the isolating solenoid. It should beconnected to the terminal which isalso used for all the small blackwires, NOT the terminal with thesingle black wire connecteddirectly to engine ground.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 26
25
Spanner torque settingsTightening Torques for general use bolts and nuts
ITEM Size x Pitch kgf .m ft .lbs N.m
M6 (7T) : 6mm (0.24in) – 1.0~1.15 7.2~8.3 9.8~11.3
M8 (7T) : 8mm (0.31) – 2.4~2.8 17.4~20.3 23.5~27.5
M10 (7T) : 10mm (0.39in) _ 5.0~5.7 36.2~41.2 49.0~55.9
M12 (7T) : 12mm (0.47in) _ 7.9~9.2 57.1~66.5 77.5~90.5
Tightening Torques for special use bolts and nuts
ITEM Size x Pitch kgf.m ft.lbs N.m
Head Bolts M10 x 1.25 6.5 ~7.0 47.0~50.6 63.7~68.6
Bolts, Connecting Bolts M8 x 1.0 4.2~4.7 30.4~34.0 41.2~46.1
Bolts, Flywheel M10 x 1.25 5.5~6.0 39.8~43.4 53.9~58.8
Bolts 1, Bearing Case M8 x 1.0 3.0~3.5 21.7~25.3 29.4~34.3
Bolts 2, Bearing Case M9 x 1.25 5.0~5.5 36.2~39.8 49.0~53.9
Nozzle Holder Assembly M20 x 1.5 5.0~7.0 36.2~50.6 49.0~68.6
Caps Nuts, Head Cover M7 x 1.0 0.7~0.9 5.1~6.5 6.9~8.8
Glow Plugs M10~1.25 2.0~2.5 14.5~18.1 19.6~24.5
Oil Switch PT 1/8 1.5~2.0 10.8~14.5 14.7~19.6
Nuts, Rocker Arm Bracket M7 x 1.0 2.2~2.7 15.9~19.5 21.6~26.5
Bolts, Idle Gear Shaft M6 x 1.0 1.0~1.15 7.2~8.3 9.8~11.3
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 27
ALIGNMENT
Alignment must be checked forparallel (A) and concentric (B)misalignment using a set of feelergauges.
To obtain accurate alignment theflexible mountings must be adjusteduntil alignment is attained, and themountings must be locked inposition.
Once mounts are tightened,alignment must be re-checked.Coupling can now be fitted inaccordance with instructionssupplied with coupling.
• All engines shall be placed withinan enclosure separated fromliving quarters and installed so asto minimise the risk of fires orspread of fires as well as hazardsfrom toxic fumes, heat, noise orvibrations in the living quarters.
• Unless the engine is protected bya cover or its own enclosure,exposed moving or hot parts ofthe engine that could causepersonal injury shall be effectivelyshielded.
• Engine parts and accessories thatrequire frequent inspection and /or servicing must be readilyaccessible.
• The insulating materials insideengine spaces shall be notcombustible.
26
Section 3INSTALLATION RECOMMENDATIONSThe installation details contained herewith are basic guidelines to assist installation, due to great diversity of marine craft itis impossible to give definitive instructions. Therefore Beta Marine can accept no responsibility for any damage or injuryincurred during the installation of a Beta Marine Engine whilst following these guidelines.
To ensure vibration free operation, theengine must be installed on substan-tial beds, extending as far forwardand aft as possible and well bracedto form an integral part of the hull.
The engine must be installed as lowas possible on the flexible mountpillar stud. This will limit vibration
and extend the life of the flexiblemount. If necessary, fit spacer blocksbelow the mounts.
A flexible coupling should be fitted.Flexible couplings do not accom-modate bad alignment. The matingfaces of the gearbox and tailshaftmust be checked for alignment, theymust be parallel and concentric towithin 0.005” (0.127mm).
WARNING
1. Do not set the engine feet highup the flexible mount pillar stud.This will cause excessive enginemovement and vibration. Packunder the flexible mount withsteel shims securely bolted intothe engine bearer.
2. The pillar stud on the flexiblemount is secured into position bythe lower locknut, do not forgetto tighten this. Also ensure thatthe stud is not screwed too farthrough the mounting body sothat it can touch the bearer.This will cause vibration andknocking noises which are veryhard to find!!
Flexible Mount
ENGINE MOUNTING
A B
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 28
27
(a) A correctly installed engine asdescribed in this handbook will meetthe exhaust emission requirements ofDirective 2003/44/EC amending theRecreational Craft Directive94/25/EC.
(b) For compliance with exhaustemissions requirements, enginesmust have correctly installed exhaustsystems. To ensure exhaustemissions are kept within permissiblelimits it is most important to reduceexhaust back pressure to aminimum, whilst ensuring exhaust isadequately muffled. Back pressureincreases as exhaust length increasesand from bends in the exhaustsystem. The exhaust back pressure,
measured with the exhaust systemconnected and the engine running atfull speed, must not exceed 80mmHg(3.1 inches Hg / 42 inches WG).The correct measuring point is at theposition where the exhaust connectsto the exhaust manifold. That is
before the water injection elbow ordry exhaust bellows.
Wet Exhaust hose should bematched to the injection bend sizes,see above.
BD1005 BV1305 BV1505
Standard 50mm 50mm 50mm
Option 1 5/8” is available in SS 1 5/8” N/A N/A
High rise water injection bend SS 50mm 50mm 50mm
Option high rise water injection bend SS 1 5/8” N/A N/A
Cross over injection bend SS 50mm 50mm 50mm
to suit Volvo replacement engines.
EXHAUSTS
TYPICAL YACHT INSTALLATION
Anti syphon valveor T piece fitted here
300mmminimum
WaterlockSilencer
Sea water Level X
a
Allow at least10% of propellerdiameter for tipclearance to hull
If a rope cutter is fitted, allow approximately 1/2”Û for movement of engine, seemanufacturer’s literature
WARNING:
(1) One of the most commonproblems with engine installation iswater entering the exhaust manifoldfrom the exhaust system bysyphoning. This can occur when thepoint of water injection (X) on theengine is close to or below the waterline. Water entering the pistons cancause bent con rods, emulsified
engine oil and a wrecked fuel pump!Its best avoided!
(2) The diagram shows a typicalinstallation. It is essential that thesmall black rubber hose connectingthe heat exchanger with the injectionbend is removed and replaced by ahose marked ‘a’. This must be ofsufficient length to
supply either a T piece or an antisyphon valve sited at least 300mm(12 inches) above the water line andon the centre line of the boat. Thepipe then returns to the injectionbend and the sea water is pumpeddown the exhaust pipe.
(3) The exhaust back pressure shouldnot exceed 3.1 inches of Hg.
Maximum sea water level when healed(on the centre line of the boat)
Normal sea water level
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 29
Notes:
1. The mechanical fuel lift pump isfitted to all engines as standard,but if a suction head of 0.25m isrequired then an electric fuel liftpump must be fitted (ask yourdealer or Beta Marine).
2. It is very important that theexcess fuel from the injectors isfed back to the fuel tank and notback to any point on the supplyline. This will help prevent airgetting into the system.
4. Any fuel leaks in the system arelikely to cause poor starting anderratic running and must becorrected immediately.
5. A fuel/water separator must beinstalled.
6. The fuel return (leak off) pipemust loop down to be level with the bottom of the tank before itenters the top of the tank - see12. This prevents fuel ‘draindown’.
7. Fuel lines and hoses must besecured and separated orprotected from any source ofsignificant heat. The filling,storage, venting and fuel supplyarrangements and installationsmust be designed and installedso as to minimise the risk of fireand explosion. Flexible fuel hosesconnecting the engine to fueltank supply and return linesmust meet the requirements setin standard ISO7840:1995/A1:2000 and asrequired by your surveyor /authority.3. Fuel pipe sizes are: Supply (mm) Leak off (mm)
8 8
1
9
117
5
6
102
3
8 4
12
FUEL SUPPLY & LEAK OFF - A typical system is shown below
(1) Fuel tank
(2) Injection pump
(3) Injection nozzle
(4) Injection pipe
(5) Mechanical fuel feedpump with priming lever
(6) Fuel filter
(7) Fuel water separator
(8) Overflow/leak off
(9) Drain plug
(10) Air vent
(11) Stop cock
(12) Fuel pipe loop
28
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 30
29
SEAWATER INLET SYSTEM (HEAT EXCHANGER COOLED ENGINES)
Your engine is fitted with a geardriven sea water pump which sucksin seawater or raw water to cool theclosed circuit system via the heatexchanger.
1. It is very important that theseawater inlet should have astrainer system either built intothe sea cock or a high levelsystem with visual inspectionglass, as shown, mounted justabove the water line.
Water Level
2. The inlet sea cock and pipe workto the sea water pump should be22mm ID or 3/4” minimum.
3. Good access to the inlet seacockis essential so that plastic bags orsea weed trapped in the intakecan be poked out!
4. All pipe work should haveapproved marine grade stainlesssteel hose clips. Any looseclamps or bad connections can
cause flooding and sinking of thevessel.
5. If water is required for stern tubelubrication then this should betaken from a ‘T’ piece in the pipegoing from the heat exchangeroutlet to the water injection bend.
6. Scoop type water pickups shouldnever be used, as water will beforced through the pump andinto the exhaust system whilst
the vessel is in motion. This isvery dangerous as the exhaustwill eventually fill and raw waterwill back up into the enginethrough the exhaust valve.Catastrophic failure will result assoon as the engine is restarted.
Note: The maximum lift of the seawater pump is 2m
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 31
30
CALORIFIER SYSTEMAll Beta engines can be fitted withthe engine tappings to allow the hotwater from the closed freshwater/antifreeze system to circulatethrough a calorifier tank which inturn heats up domestic water.
Calorifier tappings on this range ofengine are shown.
1. The big problem with a calorifieris to remove all the air from thesystem. If this is not achievedthen they don’t work!
2. Try and keep the supply andreturn pipes either horizontal orsloping down in a continuous falltowards the calorifier. This avoidsair pockets being created.
3. Extra care must be taken whenfirst filling the calorifier circuitsystem with 50% antifreeze towater solution as the engine mayappear to be full but it soondisappears into the calorifier pipework. Run the engine off load for10 minutes then check the levelas described in ‘Filling The FreshWater System’.
Also check to see if the pipegoing to the calorifier is gettingwarm after 15 mins. Top up thewater level as required and runfor another 10 minutes thenrepeat.
4. If the water level is steady but nowarm water is getting to thecalorifier then very carefully openthe calorifier bleed valve (seemanufacturers instructions) or ifnone is provided then verycarefully loosen the jubilee clipsecuring the supply pipe to thecalorifier . Air should escape.Refasten securely when nofurther bubbles are seen.
CAUTION
Do not do this when the engine ishot as scalding hot water may beforced out of the pipe under pressure.
Calorifierreturn (heatexchangeonly)
Calorifiersupply(BD1005)
Calorifiersupply(BV1305 &BV1505)
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 32
31
ELECTRICAL INSTALLATIONS
Beta has 6 panels: A -standardAB or ABV or ABVWBC
The engine harness is common to all.1. These panels must not be
installed where sea water spraycan get at them. A suitable flap orcover must be fitted.
2. Panels must be fitted in a locationwhere the helmsman can eithersee or hear the alarm system.
3. For standard wiring diagrams seefollowing pages.
4. Extension looms longer than 3m(10 feet): As an option, Beta canprovide various lengths ofextension looms for runs of over3m, but this kit includes a start
relay to overcome the voltagedrop. (See drawing 300-58520)
5. All electrical equipment must beprotected from sea water. Seawater or rust in the starter willinvalidate the warranty.Care must be taken whenpushing the two halves of theplug together to ensure thatindividual pins do not fall out. Toprevent corrosion and assist inassembly we recommend that theplug is packed with petroleumjelly (Vaseline) and then carefullypushed together. The plastic bootsshould cover both halves andoverlap. A cable tie is then putaround to hold the two halves inposition and help prevent anyingression of water.
6. All cables must be adequately
clipped and protected fromabrasion.
7. Electrical systems shall bedesigned and installed so as toensure paper operation of the craftunder normal conditions of useand shall be such as to minimiserisk of fire and electric shock.
8. Attention shall be paid to theprovision of overload and short-circuit protection of all circuits,except engine starting circuits,supplied from batteries.
9. Ventilation shall be provided toprevent the accumulation ofgases, which might be emittedfrom batteries. Batteries shall befirmly secured and protected fromingress of water
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 33
32
APPENDICES –WIRING DIAGRAMS & GENERAL ARRANGEMENTS
1. Typical starter motor ratings
2. Suggested engine starter battery size Page 33
3. Keyswitch terminations Page 33
4. Standard harness (65 Amp) 200-05452 Page 34
5. Standard harness (100 Amp) 200-06077 Page 35
6. Diagram of A panel & cut-out 200-06516 Page 36 & 37
7. Diagram of AB panel & cut-out 200-06517 Page 38 & 39
8. Diagram of ABV panel & cut-out 200-06519 Page 40 & 41
9. Diagram of ABVW panel & cut-out 100-06333 Page 42 & 43
10. Diagram of B panel & cut-out 200-06520 Page 44 & 45
11. Diagram of C Deluxe panel & cut-out 200-06518 Page 46 & 47
12. Split charge diagram –65 Amp alternator 300-62210 Page 48
13. Starter booster relay 300-58520 Page 49
14. GA of BD1005 H/E – PRM 80 100-99550 Page 50
15. GA of BD1005 H/E – TMC 40 100-01939 Page 51
16. GA of BD1005 H/E – PRM 80 Atomic 100-05009 Page 52
17. GA of BV13/1505 H/E – PRM 120 100-98915 Page 53
18. GA of BV13/1505 H/E – TTMC35A 100-06375 Page 54
19. GA of BV13/1505 H/E – PRM 150 100-99660 Page 55
20. 100 Amp alternator information 100-05471 Page 56
21. Beta Controller information Page 57 & 58
22. Wiring 100 Amp & Beta Controller 100-05475 Page 59
23. Declaration of Conformity for Recreational Craft Page 60 & 61
24. Maintenance record and service items Page 65
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 34
Engine (cc) Typical Battery Capacity (AH) Typical C.C.A. (A)at a 20hr Rate Cold Cranking Amperage
BD1005 65 ~ 75 450 ~ 540
BV1305 70 ~ 75 450 ~ 540
BV1505 70 ~ 75 450 ~ 540
33
Engine Starter capacity (kW)
1000cc to 1500cc 1.2
KEYSWITCH TERMINATIONS
The standard panel keyswitch can beused to tap off a switched positiveignition feed to power additionalgauges. In this way these gauges willonly be live whilst the engine isrunning, the engine is starting or theheaters are being used.
For silver keyswitches, the terminalto achieve this ignition switchedpositive is marked ‘AC’.
For black keyswitches, the terminalto achieve this ignition switchedpositive is marked ‘15/54’.
For panels without any keyswitch,gauges can be driven from the 1mm2
brown wire which terminates at 11way connector terminal 4. This is alow power switched positive, anyadditional power required from thisconnection must be fed through arelay, as noted below.
Note: these terminals are rated at 10amps maximum, since they arealready utilised for panel andalternator feeds Beta Marinerecommend any additionalrequirements from these terminalsmust be fed through a relay. Thisrelay should then be connected to it’sown fused positive supply directlyfrom the engine battery. Beta drawing202-06421 illustrating the wiring ofa typical electric fuel lift pump withignition switched relay can besupplied upon request.
SUGGESTED MINIMUM ENGINE STARTER BATTERY SIZE:
TYPICAL STARTER MOTOR RATINGS:-
Starters used in Kubota engines have the following standard capacities
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 35
34
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 36
35
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 37
36
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 38
37
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
515
/11/
2004
2A P
AN
EL
TW LT
MA
TL:
00
10.0
010
.00
150.
00
10.0
0
10.0
0
90.0
0
5.00
140.
00
5.00
80.0
0
50.3
2AD
D 30
mm
FOR
WIR
ES
20.12 36
.68
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 39
38
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 40
39
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
415
/11/
2004
2AB
PA
NE
L
TW LT
MA
TL:
01
10.0
010
.00
195.
00
10.0
0
10.0
0 180.
00
50.3
2AD
D 30
mm
FOR
WIR
ES
22.6
2
36.6
8
5.00
185.
00
5.00
170.
00
O 5
.00
THRU
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 41
40
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 42
41
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0632
0/01
23/1
1/20
04
AB
V P
AN
EL
TW LT
MA
TL:
00
140.
0
10.0
180.
0
10.0
10.0
O 5
.0 T
HRU
5.0
5.0
170.
0
130.
0
20.0
20.0
22.6
50.3
ALLO
W30
mm
FOR
WIR
ES36
.7
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 43
42
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 44
43
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0633
101
/12/
2004
AB
VW
WA
TER
PR
OO
FP
AN
EL
TW LT
MA
TL:
AS U
SED
ON K
1474
4
00
180.
00
10.0
016
0.00
5.00
20.0
0
5.00
10.0
0
120.
0014
0.00
5.00
20.0
0
5.00
50.5
0AL
LOW
30m
m F
OR W
IRES
22.6
2
O 5
.00
THRU
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 45
44
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 46
45
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
315
/11/
2004
2B P
AN
EL
TW LT
MA
TL:
00
210.
00
10.0
010
.00
10.0
0165.
00
5.00
200.
00
5.00
155.
00
50.3
2AL
LOW
30m
m F
OR W
IRES
22.6
236
.68
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 47
46
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 48
47
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
615
/11/
2004
2CP
AN
EL
TW LT
MA
TL:
DE
LUXE
00
10.0
010
.00
298.
00
10.0
0166.
00
10.0
0
5.00
288.
00
5.00
156.
00
50.3
2AD
D 30
mm
FOR
WIR
ES
22.6
2
36.6
8
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 49
48
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 50
49
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 51
50
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 52
51
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 53
52
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 54
53
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 55
54
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 56
55
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 57
56
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 58
57
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 59
58
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 60
59
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 61
60
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 62
61
Emission durability. IN RESPECT TO THE RECREATIONAL CRAFT DIRECTIVE 94/25/EC AND AMENDMENT2003/44/EC ANNEX 1, B3.
The engine must be installed, maintained and operated within the parameters detailed in theOperator’s Maintenance Manual. Maintenance must use approved materials, parts andconsumables. Should the engine lie unused for a period in excess of 6 months it must beinhibited otherwise it will deteriorate with resulting decrease in performance. See also theWinterising and Laying Up procedures in the Operator’s Maintenance Manual.
The fuel settings of the diesel injection system must not be tampered with otherwise theguarantee will be invalid and the performance may fall outside prescribed limit. Suchadjustment cannot be allowed under the terms of the emission certification.
Performance of the engine depends upon the use of correct fuels, lubricants and inhibitors.These are fully detailed in the Operator’s Maintenance Manual.
Particular attention must be paid to the installation with respect to the exhaust system. Thesystem must be designed so that water cannot back feed into the engine. The run must besuch that the back pressure at the engine manifold does not exceed the level detailed in theOperator’s Maintenance Manual. Wet, water injected, exhaust systems must be at least thebore mentioned in the Operator’s Maintenance Manual and should the run be excessive thisbore must be increased accordingly. Back pressure is measured at the outlet of the enginemanifold before the water injection bend or dry bellows.
Our experience over 14 years has shown that properly installed and maintained engines holdtheir performance without major mishap even when running hours exceed those mentioned inthe Recreational Craft Directive. It is the owners / users responsibility to ensure that the enginecontinues to function properly and any malfunction must be immediately investigated. TheTrouble Shooting section as detailed in the Operator’s Maintenance Manual is particularlyhelpful in this respect. Engine performance, especially with respect to erratic running, exhaustcondition, low power output and high oil consumption are indications of engine conditionsthat may result in emissions outside the prescribed limits and must therefore be investigatedand rectified immediately.
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 63
62
NOTES
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 64
63
NOTES
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 65
Quick Reference Parts ListingHEAT EXCHANGER COOLED BD1005, BV1305 AND BV1505
In all cases please quote the Beta Marine WOC “K” number and engine number.
Description Part Number Qty per Engine
Heat Exchanger “O” Ring 209-80110 2
Wasting Zinc Anode 209-61840 1
Lubricating Oil Filter 211-60390 1
Fuel Filter – Heat Exchanger cooling 211-60210 1
Fuel Lift Pump 600-67830 1
Fuel Lift Pump Gasket 600-00065 1
Air Filter Element – BD1005 only 211-62950
Air Filter Element – BV1305 & BV1505 only 211-61831
Sea Water Pump Service Kit (includes *) 207-61470 1
Sea Water Pump Impellor * 207-79630 1
Sea Water Pump Cover Plate “O” Ring * 207-04206 1
Sea Water Pump Cover Plate 207-05305 1
Sea Water Pump Cover Plate Bolt 207-04207 3
Sea Water Pump Seal * 207-02239 1
Thermostat 600-72450 1
Thermostat Gasket 600-80490 1
40 Amp Blade Fuse - engine wiring harness 200-00959 1
Control Panel Key Switch 600-00057 1
Control Panel standard Key 600-00058 1
Water Temperature Switch (Panel A, ABV, ABVW) 200-01133 1
Water Temperature Sender (Panel C & B) 200-94360 1
Oil Pressure Switch (Panel A, ABV, ABVW) 600-62670 1
Oil Pressure Sender (Panel C & B) 200-94350 1
Vee Belt – standard 65 Amp alternator 214-63090/Q 1
Optional Polyvee Belt – 100 Amp alternator 214-00493 1
64
1
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 66
65
Service Record
Service Date Responsible
1 Commissioned
2 First 25 hours
3 First 50 hours
4 Every 150 hours with Shallow sump
5 Every Year / Every 250 hours if sooner
6
7
8
9
10
11
12
13
14
15
beta small engine ref 1640.qxd 15/9/06 1:59 pm Page 67
Beta Marine Limited, Davy Way, WaterwellsQuedgeley, Gloucester, GL2 2AD, United Kingdom
Tel: +44 (0)1452 723492 Fax: +44 (0)1452 883742
email: sales@betamarine.co.uk www.betamarine.co.uk
Keel Cooled 10 to 90bhp Beta Marine Generating Sets 3.7 to 40kVA
Beta Marine Generating Sets 30 to 900kVA
Sail Drives 13.5 to 50bhp
Heat Exchanger Cooled 10 to 90bhp
BM Doc Ref: 1640 28-37.5bhp H/E
ww
w.m
ono-
stud
io.c
o.uk
beta small engine ref 1640.qxd 15/9/06 2:00 pm Page 68
top related