Installing Deadbolt a. b. Tools Needed: Deadbolt A B Apdf.lowes.com/installationguides/723079894348_install.pdf · Place the Collar over the hole, and insert the Cylinder into the

If you have a new door that is notpre-bored, follow these instructions.If your door is pre-bored, proceed toSingle Cylinder or Double CylinderInstallation. The template providedmust be taped to the door as shownto mark locations for drilling holes.To position the template, fold thetemplate on line and locate on doorat specified height (about 40” fromthe floor). If the door is beveled,place the folded edge on the lowside of the bevel as shown in theillustration. Determine the doorthickness and backset (2-3/8” or 2-3/4”). Mark the door for face and edge bores.

Tools Needed: Door Preparation

Tools Needed: Deadbolt Installation

Exploded View Single Cylinder Deadbolt

Exploded View Double Cylinder Deadbolt

Parts Enclosed:

If your door is not pre-bored, see Door Preparation section.1. Pencil2. Measuring Tape or Rule3. 2-1/8” Diameter Hole Saw4. 1/2” or 3/4” Wood Chisel5. Drill and assorted bits 1/8”,

5/32” and 1”

1. 2 each #8 - 32 Oval Head Machine Screw 2. 1 Turnpiece Trim3. 2 each #10 -32 x 1-7/8” Pan Head Machine Screw4. 1 Turnpiece Mounting Plate5. 1 Adjustable Backset Deadbolt6. 4 each #8 x 3/4” Flathead Combination Screws7. 1 Outside Cylinder Collar8. 1 Outside Cylinder9. Screw Guide

Parts Enclosed:1. 1 Inside Cylinder Collar2. 1 Cylinder Cover3. 2 each #10 -32x2-1/4” Flat Head

Machine Screws4. 1 Inside Cylinder5. 1 Threaded Collar

Note: See Strike Installation section for strike parts listing.

Note: See Strike Installation section for strike parts listing.

6. 1 Adjustable Backset Deadbolt7. 4 each #8 x 3/4” Flathead

Combination Screws8. 1 Outside Cylinder Collar9. 1 Outside Cylinder10. Screw Guide

1. Measuring Tape or Rule2. One pair needle-nose pliers3. One pair slip joint or lineman’s

pliers4. No. 2 and No. 3 Phillips Head

Screwdrivers5. 1/8” Allen Wrench (supplied)6. Flat Head Screwdriver

Chisel out the area marked for thefaceplate to a depth of 5/32” oruntil the faceplate is flush withthe door edge. Proceed to the“Installing the Deadbolt” section.

Insert deadbolt into edge of door.While holding faceplate, trace theoutline of the faceplate onto thedoor edge. Mark screw holecenters and drill pilot holes with a1/8”drill.

Drill the 2-1/8” diameter face bore (A) through the door.Drill 1” diameter edgebore (B) 3-1/2” deepfor 2-3/8” backset, or3-7/8” deep for 2-3/4”backset. To ensure thecorrect depth of hole Bmark your drill bitusing masking tape asshown in the illustra-tion.

Caution: Re-checkhole locationsbefore drilling.

A- 2-1/8” DIAMETERB- 1” DIAMETER Face bore

Edge bore

A

B

Door Preparation

b. Place the Turnpiece MountingPlate over the bore on the inside ofthe door. When positioned properlythe word “Top” will be at the 12o’clock position and against thedoor ( not visible). Insert two #10-32 x 1-7/8” pan head machinescrews through the two holes inthe Mounting Plate, through thedeadbolt, and into the threadedholes on the back side of theCylinder. Check that the MountingPlate is centered on the bore in thedoor and rests flat against thedoor. Tighten the screws.

Installing Deadbolt

Double Cylinder Assembly

a. Extend the deadbolt using a flat headscrewdriver as shown. From the outsideof the door, place the Screw Guide in thebored hole so that it fits around theDeadbolt. Note: The screw guidemust be mounted from the exteriorside of the door. The arrow on thescrew guide must be visible andpointing up. Place the Collar over thehole, and insert the Cylinder into theCollar and Deadbolt. Note: Cylinder tailpiece must be vertical when installingcylinder. Hold in place while moving tostep b. Do not insert key into theCylinder during this procedure.

b. Insert deadbolt. Secure with two #8 x 3/4" flathead combination screws provided (see diagramfor proper positioning). Ensure deadbolt head isextended throughout installation procedure.

a. Carefully break off cylindertailpiece at required mark for yourdoor thickness.Caution; use twopairs of pliers as shown or tailpiece will be damaged.

b. Align tailpiece with slot.Keep tailpiece vertical andcurved toward right side ofthe hole as illustrated.

c. Place the TurnpieceTrim over the MountingPlate. The turnpiecemust be horizontal asshown in the illustration.The cylinder tailpiece, inthe vertical position,must slide into the turn-piece slot. Attach theTurnpiece Trim to theMounting Plate with two#8-32 x 5/8” oval headmachine screws. Tightenthe screws.

a. Extend the deadbolt using a flathead screwdriver as shown. Fromthe outside of the door, place theScrew Guide in the bored hole sothat it fits around the Deadbolt.Note: The screw guide mustbe mounted from the exteriorside of the door. The arrow onthe screw guide must be visible and pointing up. Placethe Collar over the hole, andinsert the Cylinder into the Collarand Deadbolt. Note: Cylinder tailpiece must be vertical wheninstalling cylinder. Hold in placewhile moving to step b. Do notinsert key into the Cylinderduring this procedure.

b. Insert the Inside Cylinder into thehole in the Threaded Collar. The slot inthe top of the Inside Cylinder engagesthe notch in the Threaded Collar. Placethese two components into the bore onthe inside of the door so that the tail-piece from the Inside Cylinder engagesthe slot in the Deadbolt. Insert two #10-32 x 2-1/4” flat head machinescrews into the two holes on the InsideCylinder and tighten them down to connect the components on the outsideof the door. Note: the tailpiece on thecylinder must be vertical and towardsthe right side of the hole during this procedure. Do not insert the key intoeither cylinder during this step.Tailpiece

OUTSIDE

INSIDE

Install deadbolt withboth long slots on latchbody in upper position.

Cylinder

Slot

Single Cylinder Assembly

OUTSIDE

Rotate toadjust backset.

INSIDE

a. The deadbolt supplied withthis unit has an adjustable back-set feature. When removed fromthe box it will be set at 2-3/8”backset. To adjust the deadbolt to2-3/4” backset, grasp the bodyand twist thefaceplate / boltheadassembly 180 degrees until itstops. The unit is now ready forinstallation in 2-3/4” backset.

TEAR HERE FOR ENGLISH.TEAR HERE FOR ENGLISH.

INSIDE

TOP VIEW

OUTSIDECYLINDER

CYLINDERTAILPIECES

MUST MEET EACHOTHER AS

SHOWN

c. Align the cylinder cover overthe inside cylinder. Screw on theinside cylinder collar.

INSIDE

Tailpiece

Break withthis plier

Cylinder

Hold withthis plier

INSIDE

Top view of door

Template

AB

Low side of bevel

DoorThickness

backset

2-1/8” Deadbolt Preparation

TEAR HERE FOR ENGLISH.

PK-1229E (08/10)

Tahoe 2-1/8” CollarAuxiliary DeadboltInstallation Instructions

Logotype: Builders Hardware Manufacturers

consider using it on your company stationery, brochures, and print advertising.

Congratulations!

Remember Baldwin

With your purchase of The Images Collection solid brass deadbolt, you’re among a groupof discerning individuals who know the intrinsic value of selecting the finest – Baldwin.

Images entrance locksets, interior latchsets, and deadbolts coordinate beautifully, enabling youto carry a specific design theme throughout your home.

Our step-by-step installation instructions will help guide you through yourproject quickly and easily.

Before you begin your installation, read and understand theinstallation instructions and marking templates. If you have anyquestions, please do not hesitate to contact our Baldwin Technical Services Department,1-800-566-1986. We’re here to help!

NOTE: Failure to use all recommended components will void Grade 1 rating.

We thank you for your Baldwin purchase and wish you the fullestenjoyment of your Baldwin Handleset.

With the completion of your project, remember that Baldwin qualityhardware products are available for all your decorating and remodel-ing needs. Matching knob and leversets for interior doors, beautifulbath accessories, and a complete selection of cabinet and doorenhancing hardware are all available from your Baldwin retailer.

©2010 Baldwin Hardware CorporationLake Forest, California, 92610

Technical Services Support1-800-566-1986

Hours: 8 a.m. to 8 p.m. E.S.T - Monday - Friday 10 a.m. to 6 p.m. E.S.T - Saturday

Strike Installation

Complete deadboltinstallation beforeinstalling the strike.Install weather stripping before setting the strike. Closethe door and extend thedeadbolt several timesagainst the door frame.The strike centering indicator will leave a center mark on the doorframe to aid in locatingthe strike. (fig. 1)

Using reinforcing strike as a template, marklocations for reinforcing screws. (fig 3) Drilltwo 5/32" dia. pilot holes for the 3" longscrews and two 1/8" dia. pilot holes for the#8 x 3/4" screws. Mark drill points 5/16"above and below centering point. Bore two1" dia. holes 1-1/4" deep at these points.Chisel out holes for dust box. (fig. 4)

Position strike plate on centermark. Align and trace outsideof strike and mounting screwsonto the door frame. (fig. 2)

Chisel out thearea marked instep (2) 7/32"deep or until thestrike box, reinforcing strikeand strike platefits inside mortiseand flush withthe door frame.(fig. 5)

5 Install strike as illustrated.

Bore 1" dia. holeabove and belowcentering point.

Drill 1/8" dia. pilot holesfor # 8 screws.

Drill 5/32" dia. pilotholes for 3" screws.

5/16" abovecenter point.

5/16" below center point.

fig. 4

fig. 51. Dust Box2. Reinforcing Strike3. #8 x 3/4" Combination Screws (2)4. 3" Reinforcing Screws* (2)5. Strike Plate6. #8-32 x 1/4" Machine Screws (2)

*Note:Lubricant recommendedwhen installing 3" reinforcing screws.

TEAR HERE FOR ENGLISH.

OUTSIDE

INSIDE INSIDE

center line