HU 121 History of Engineering and Technology Prof. Dr. Abdelsamie Moet Fall 2013/14 Pharos University in Alexandria Faculty of Engineering Steam and Internal.
Post on 16-Dec-2015
218 Views
Preview:
Transcript
HU 121 History of Engineering and Technology
Prof. Dr. Abdelsamie MoetFall 2013/14
Pharos University in AlexandriaFaculty of Engineering
Steam and Internal Combustion Engines
Lect6
HU121_Lect6_SteamEngines 2
Steam Engine: Definition
• A steam engine is a heat engine that converts steam energy into mechanical motion.
• Steam may be produced by combustion or no-combustion heat.
• Combustion heat sources include:– Hydrocarbon (Oil, Gas and Coal), – Biomass.
• Non-combustion heat sources include:
– Solar, – Nuclear or – Geothermal.
HU121_Lect6_SteamEngines 3
Evolution of Steam Engines
100 BC: the Aeolpile
1629 Giovanni Branca1551
Taqi al-Din600 Years
2010Steam Turbine
HU121_Lect6_SteamEngines 4
100 BC: the Aeolpile• Hero of Alexandria, developed
the "aeolipile”.
• It consisted of a boiler, two bent tubes mounted to a sphere.
• Steam coming from the boiler entered through the two tubes.
• The steam then exited through the bent tubes on the sphere, causing it to rotate.
HU121_Lect6_SteamEngines 5
Steam Engines by Taqi al-din and Branca
• In 1551, Taqi al-Din was the first to describe steam turbine device in his book “Al-Turuq al-saniyyafi al-alat al-ruhaniyya” (The Sublime Methods of Spiritual Machines).
• Later in 1629 Giovanni Branca described a related device.
HU121_Lect6_SteamEngines 6
• Taqi al-Din Muhammad ibn Ma'ruf al-Shami الشامي معروف بن محمد الدين ,تقي
• (1526–1585) was an Ottoman Muslim polymath: He received his education in Cairo, Egypt where he studied astronomy, mathematics, medicine, and Islamic law.
• Lived in Damascus, Cairo and Istanbul. • He was the author of more than 90 books on a wide
variety of subjects, including astronomy, clocks, engineering, mathematics, mechanics, optics and philosophy
HU121_Lect6_SteamEngines 7
Taqi al-din Steam Engine: as described in his book “Al-Turuq al-saniyyafi al-alat al-ruhaniyya”
• One of these methods is to have at the end of the spit a wheel with vanes,
• Opposite the wheel place a hollow pitcher made of copper with a closed head and full of water.
• The nozzle of the pitcher is placed opposite the vanes of the wheel.
• Kindle fire under the pitcher and steam will exit from its nozzle in a restricted form and it will turn the vane wheel.
• When the pitcher becomes empty of water bring close to it cold water in a basin and let the nozzle of the pitcher dip into the cold water.
• The heat will cause all the water in the basin to be attracted into the pitcher and the [the steam] will start rotating the vane wheel again.”
HU121_Lect6_SteamEngines 8
1629: Branca’s
• In 1629 an Italian engineer, Giovanni Branca, described a stamping mill.
• A jet nozzle directed steam onto a horizontally mounted turbine wheel, which then turned an arrangement of gears that operated the stamping mill.
HU121_Lect6_SteamEngines 9
1687: Newton’s Wagon• Newton attempted to
put his newly formulated laws of motion to the test.
• He tried to propel a wagon by directing steam through a nozzle pointed rearward
• Steam was produced by a boiler mounted on the wagon.
• Due to lack of power from the steam, this vehicle didn't operate.
But he conceived “moving” engine
HU121_Lect6_SteamEngines 10
The London Steam Carriage
• was an early steam-powered road vehicle constructed by Richard Trevithick in 1803
• The world's first self-propelled passenger-carrying vehicle.
• Trevithick later developed a steam locomotive on rails.
HU121_Lect6_SteamEngines 11
Concept of Uniflow Steam Engine
• Schematic animation of a uniflow steam engine.
• The valves are controlled by the rotating camshaft at the top.
• High pressure steam enters, and exhausts.
HU121_Lect6_SteamEngines 12
Internal combustion engine• converts the energy of a fuel-air mixture
burning within a combustion chamber into mechanical energy.
Reciprocating internal combustion engine is an engine, in which burning process occurs within a cylinder equipped with a piston driven by the pressure of the combustion gases.
• The gas pressure force is transmitted to the crankshaft linked to the piston by means of a connecting rod.
• The crank mechanism transforms the alternating linear motion of the piston into the rotation of the shaft.
HU121_Lect6_SteamEngines 13
The four-stroke cycle1. Intake: sucking the fuel-air mixture into the
cylinder.
2. Compression: compressing the gaseous fuel-air mixture. The compression causes pressure and temperature increase of the gas in the cylinder.
3. Ignition fuel-air mixture is ignited and fuel combustion starts. Combustion increases the gas pressure and temperature. In the gasoline (petrol) engines ignition is as a result of a spark produced by the spark plug.
4. Exhaust: forcing the combustion gases out of the cylinder.
HU121_Lect6_SteamEngines 14
HU121_Lect6_SteamEngines 15
Steam Turbine• A steam turbine consists of one or
more rotors (rotating discs) mounted on a drive shaft, alternating with stators (static discs) fixed to the turbine casing.
• The rotors have a blades at the outer edge.
• Steam acts upon these blades, producing rotary motion.
• The stator blades redirect the steam flow onto the next rotor stage.
HU121_Lect6_SteamEngines 16
Jet Engine
• A fan in the front sucks air in.
• A compressor raises the pressure of the air.
• The compressed air is then sprayed with fuel and an electric spark lights the mixture.
• The burning gases expand and blast out through the nozzle, at the back of the engine.
• As the jets of gas shoot backward, the engine and the aircraft thrust forward.
HU121_Lect6_SteamEngines 17
Jet Engine Animation
HU121_Lect6_SteamEngines 18
Review Question
1. Present a brief timeline of the steam engine.2. Specify the design concept used by Taqi al-din in his
steam engine.3. Describe “Newton’s steam wagon, identify its limitation
and its contribution to the development of engines.4. Compare steam engine and internal combustion
engine.5. Outline the concept of “uniflow” steam engine. 6. Describe the basic components of a historical steam
engine, modern steam engine and a jet engine.
HU121_Lect6_SteamEngines 19
top related