Erection drawing details Assembly instructions / spare ... · Erection drawing details Assembly instructions / spare parts list for pillar-mounted slewing cranes, type M Meister Main
Post on 20-Apr-2020
37 Views
Preview:
Transcript
1 / 42 M_Meister_Hauptanleitung_EN10.06
Erection drawing details Assembly instructions / spare parts list
for pillar-mounted slewing cranes, type M Meister
Main instructions, issue 10.2006 EN Scope of a pillar-mounted slewing crane of standard / basic design:
Slewing range max. 360° (infinite) or limited mechanically by stops Manual slewing Power supply by means of cable supporting tube or round trailing cable
Note: When the slewing crane features other accessories such as an electrical slewing drive, the power supply is modified and additional components are required. For such case supplementary instructions are provided.
Table of content
1. General.....................................................................................................................2 2. Pillar assembly ......................................................................................................8 3. Pre-assembly of jib.............................................................................................11 4. Jib completion .....................................................................................................13 5. Assembly instructions for trolley end stops..............................................14 6. Round power supply cable (with cable supporting tube) ....................22 7. Round power supply cable (with cable tensioning rope) .....................23 8. Final jib assembly...............................................................................................25 9. Precise alignment of pillar and jib ...............................................................27 10. Installation of electrics without slip-ring unit..........................................28 10. Installation of electrics with slip-ring unit ................................................29 12. Assembly of the slip-ring unit ........................................................................30 13. Electrical installation of the mains connection switch ..........................32 14. Slewing end stop .................................................................................................33 15. Undergrouting and anchorage (system ANKERFIX)...........................36 16. Putting into operation.......................................................................................38 17. Technical information ......................................................................................39 18. Spare parts list.....................................................................................................40
2 / 42 M_Meister_Hauptanleitung_EN10.06
1. General
1.1 Standard / basic crane design - schematic diagram (Execution: design with chain hoist and round trailing cable power supply)
For customized slewing cranes this documentation will be completed by a layout drawing and a circuit diagram, if required. For the exact type of crane, please refer to the order acknowledgement and the documentation included in the supply. Slewing cranes, models M and TS shall only be equipped with hoist units with a rated capacity of max. 1.6 times the crane’s SWL (load capacity). The total weight shall not exceed the permissible total weight as specified in the master data sheet. The illustrations in the present manual are symbolic and may deviate from the actually supplied equipment.
Pos./Item Benennung Designation Standsäule Pillar
S1 Säule Pillar S2 Fußflansch Foot flange S3 Säulenring Pillar ring S4 Kopfplatte Top plate
Ausleger Jib
A1 Trägerprofil Girder profile A2 Auslegerstütze Jib support A3 Rollenkasten mit
Lagerung Roller box with bearing
M Mittelzapfen mit Lagerung
King pin with bearing
A15 Hebezeug Hoist
M A1
A15 A2
A3
S4
S3
S1
S2
3 / 42 M_Meister_Hauptanleitung_EN10.06
1.2 General information for crane installation
1.2.1 The cranes and crane components are designed for single shift operation under normal
operating conditions. These instructions refer to the first assembly of the crane at its place of destination. Dismantling and re-erection of the crane are subject to additional inspection works. Please contact the manufacturer!
1.2.2 Field of application The cranes and crane components are designed for single shift operation under normal operating conditions. In case of higher demands on the cranes or special ambient conditions (i.e. higher frequency of use, high ambient temperature, radiation and explosion hazards, aggressive or abrasive atmosphere), the use of the crane and its components must be checked!
1.2.3 Requirements on supporting structures for slewing cranes
o Slewing cranes only work perfectly on a horizontal surface of sufficient strength and rigidity.
o Deformations of the supporting surface provided by the customer shall not exceed 1/1000 the distance of the surface in all slewing end positions with nominal load. Open sections such as double tee booms are subject to torsion and, if necessary, have to be reinforced.
o Important: The effective direction of cutting forces changes in the slewing positions!
o Contact or supporting surfaces must be even in the horizontal and vertical direction, respectively. The admissible deviation shall not exceed 1/1000 of the largest distance.
o Even floor bases must be available if crane pillars are mounted on anchor plates, top
and compact anchor pads, intermediate plates, machines or steel structures! Generally, cranes designed for concrete footing (standard design) do not provide an even surface!
o The supporting structure must not be subject to vibrations and oscillations.
o We are not liable for supports, columns, walls, bracings, floors, etc. provided by the
customer. Therefore, the supporting structure must be checked by the customer prior to the crane installation. Cutting forces are specified in our data sheets, catalogues, offers and order confirmation or are available on request.
o We will refuse any claims resulting from an insufficient supporting structure or from imperfect fastening.
o We expressly refer to the national and regional building regulations, the directives of building authorities etc..
4 / 42 M_Meister_Hauptanleitung_EN10.06
1.2.4 The installation has to be carried out by experienced expert companies or qualified
technicians (see BGV D6, § 26). In case of questions, please contact your supplier.
1.2.5 Slewing cranes only work perfectly, if they are erected in accordance with this manual and on
the condition that inspections and maintenance works are executed on a regular basis.
1.2.6 The non-observance of the assembly instructions, operating instructions and regulations of the Industrial Employers' Mutual Insurance Association present a risk to the safety of the operation and result in a refusal of claims.
1.2.7 Only use factory-supplied spare parts.
1.2.8 Prior to start the assembly, check centrelines and heights at site and compare same with the
crane design. Observe the specified safety distances.
1.2.9 Observe the manufacturer’s instructions for hoist units and slewing drives as well as for any other accessories.
1.2.10 For the outdoor use, hoists and slewing drives must be weather-protected. Appropriate shielding is available from the manufacturer/supplier.
1.2.11 The electrical installation works must only be carried out by a qualified specialist.
1.2.12 The assembly shall only be carried out when the power is off.
1.2.13 For cranes operated outdoors, the cable openings for earth and supply cables in the jib need additional sealing.
1.2.14 Install hoist unit and trolley strictly in compliance with the manufacturer’s/supplier’s
instructions.
1.2.15 Observe manufacturer’s instructions in respect of electrical protection.
1.2.16 Follow the inspection instructions according to § 19 of EN 60204-32.
1.2.17 After completion of assembly, carefully check all functions. The direction of motions must match the symbols of the control panel.
1.2.18 Crane operating instructions have to be attached on the crane, e.g. on the pillar, and shall be easily perceptible.
1.2.19 Prior of the start-up of motorized cranes and cranes with a capacity of more than 1000 kg, carry out the inspections according to the applicable regulations, e.g. UVV-Cranes BGV D6 , §25.
1.2.20 Observe manufacturer’s instructions for the operation and maintenance of cranes, hoists, slewing drives and other items. Please ask us for missing manuals/instructions prior to start the installation or start-up activities.
5 / 42 M_Meister_Hauptanleitung_EN10.06
1.3 Parts list (applicable to all crane designs; for parts marked grey see separate instructions)
Mechanical equipment
Pillar King pin bearings S1 Pillar M1 King pin S2 Foot flange M2 Bearing cover plate or S3 Pillar ring Nilos ring S4 Top plate M3 King pin bearing S5 Gear ring M4 Supporting washer S6 Access opening/cover M5 Retaining ring S7 Slip ring assembly retaining plate M6 Support section S8 Mains connection switch opening for slip-ring assembly Mains connection switch retaining
plate
Trolley end stops Jib K1 UNI-trolley end stops K2 Inner end stop A1 Jib profile K3 Bottom end stop A2 Jib support A3 Roller plate Roller box A4 Roller Base plate fastening A5.1 Steel roller cover V1 M27 anchor bolt A5.2 Plastic roller cover V2 M27 adjusting nut A5.3 Cap for HT screw V3 Washer 28 A6 Front end plate V4 Supporting ring A7 Rear end plate V5 M27 hex. nut A8 M16/M20 hex. screw V6 M16 locknut A9 Spring washer A16/A20 V7 Compact anchor A10 Motor support plate V8 M27 HT screw A11.1 Safety ring V9 HT washer A11.2 Safety tape V10 M27 threaded rod A12 Hex. screw V11 98 x 6 washer A13 Spring washer V12 Top bolt A14 Hex. nut V13 Hexa. screw M27 A15 Hoist V14 Washer 28
Information plates Auxiliary items (by others)
B1 Type plate H1 Supply line provided by the customer
B2 UVV – plate H2 Bearing block B3 Name plate H3 Strip of timber approx.
100 x 500 B4 Load capacity H4 Wooden wedge B5 Danger strip H5 G clamp H6 Round steel/screwdriver H7 Spacer ring
6 / 42 M_Meister_Hauptanleitung_EN10.06
Slewing drive A Slewing drive B AA1 Hollow shaft gearbox
with motor AB1 Solid shaft gearbox
with motor AA2 Connecting element AB2 Pinion AA3 Thick washer (t=10mm) AB3 Cover plate AA4 Spring washer AB4 Spring washer AA5 Hex. screw (l=40mm) AB5 Hex. screw AA6 M8 hex. screw AB6 Hex. screw, long AA7 A8 spring washer AB7 Hex. screw, short AA8 Torque bracket AB8 Spring washer AA9 Hex. screw AB9 Hex. nut AA10 Washer AB10 Split sleeve AA11 Hollow shaft AB11 Pinion cover AA12 Slotted nut AB12 Washer AB13 Hex. nut, flat AB14 Solid shaft gearbox
with manual drive element
AB15 Adjusting screw AB16 Distance washer AB 17 Spacer sleeve AB18 Locknut AB 19 Cover Mechanical slewing stop SM1 Slewing stop, welded
type, complete with rubber buffer
SM2 Slewing stop, screw-type, complete with rubber buffer
SM3 M12 hex. screw SM4 A12 spring washer SM5 End stop cam Slewing limit switch SE1 Slewing limit switch cpl.
with support bracket
SE2 T section SE3 C-rail SE4 M8 hex. screw SE5 Washer 8,4 SE6 M8 locknut SE7 M6 hex. screw SE8 A6 spring washer SE9 Square nut SE10 M6 pin SE11 Hexagonal nut M6
7 / 42 M_Meister_Hauptanleitung_EN10.06
Electrical equipment E1 Supply cable E2 Flush-mounted mains
connection switch E3 Slip-ring assembly E4 Twist-type cable entry gland E5 Earthing lead E6 Cable ties with eye E7 Cable tube E8 Cable supporting tube E9 Clips 1 E10 Clips 2 E11 Clips 3 E12 Supporting arm E13 Supporting arm (alt. mount.) E14 Clamp, flat E15 Cable ties E16 Eye bolt E17 Rope E18 Ferrule E19 Round cable carriage E20 Supporting arm E21 Supporting arm (alt. mount.) E22 C-rail E23 Connector E24 Clamp, round E25 Fixed suspension E26 Flat cable trolley E27 Flat cable end clamp E28 Towing trolley E29 Engaging stirrup E30 Terminal box E31 On-board terminal box E32 Ideal control carriage with
terminal box E33 Ideal control carriage with
plug-type connection E34 End stop E35 Control panel E36 Contactor control box E37 Filler plates
We reserve the right to pre-assemble individual components! Due to the variety of products (different crane models) some electrical accessories included items may not be required for the assembly of your crane!
8 / 42 M_Meister_Hauptanleitung_EN10.06
2. Pillar assembly
Pillars may be fastened as follows:
Fastening on ANCHOR BOLTS / foundation Fastening on COMPACT ANCHORS / foundation *) Fastening on TOP ANCHORS / foundation Fastening on RESIN BOLTS / concrete floor *) Special fastening methods *)
2.1 Installation on anchor bolts (system ANKERFIX)
2.1.1 Note: Please check prior to the installation whether the foundation has been executed in accordance with foundation instructions and preset minimum dimensions. Remove the anchor bolt template if still in place! Anchor bolts shall not be dressed by heat treatment! Caution! Pillars featuring screw pitch circle DL shall not be directly fastened with resin bolts, dowels or equivalent fastening material! Compound anchor bolts require larger plates of a special type (Please contact us for details). In case of non-observance the crane risks to turn over!
2.1.2 Place pillar (S1) next to the foundation, lead the cable (H1) internally through the pipe and pull it out from the switch opening (S8).
2.1.3 Screw in an adjusting nut (V2) on every anchor bolt (V1), put in place a steel washer (V3) and a supporting ring (V4). Make sure that all rings (V4) are exactly on the same level! The difference in height between a top edge of the ring and another must not exceed 1/1000 of the respective distance!
It is not allowed to set up the pillar on just a few (e.g. 4) adjusted rings!
2.1.4 Position pillar (S1) onto adjusting nuts (V2), apply washers (V3) and rings (V4). 2.1.5 Secure pillar (S1) by means of washers (V3) and nuts (V5). Tighten lower adjusting nuts
(V2) as well.
2.1.6 Align pillar vertically (S1) by using a level, align it with the adjusting nuts (V2) and tighten the bolts (V5). Attention: In order to avoid that only one anchor bolt gets under excessive strain during the alignment, adjust the neighbouring nuts (V2) accordingly! The alignment of the pillar with the water level is only preliminary and rough. The crane is precisely aligned when the jib is fitted. This alignment is described in chapter 9.
2.1.7 Remove adhesive tapes on the pillar ring (S3), if any. *) Refer to separate assembly instructions
9 / 42 M_Meister_Hauptanleitung_EN10.06
When setting up the pillar (S1) please provide easy access to the main switch opening (S8) and the main switch (E2), respectively!
10 / 42 M_Meister_Hauptanleitung_EN10.06
Illustration: Fastening with anchor bolts (prior to undergrouting): Detail X
Detail Supporting ring
Supporting ring
flexible ring
11 / 42 M_Meister_Hauptanleitung_EN10.06
3. Pre-assembly of jib
3.1 Components (A1) Jib(profile) (H2) Bracket (A2) Jib support (H3) Timber strip min. 100 x 500 (A3) Roller plate / box (H4) Wooden wedge (A4) Roller (H5) G clamp (A5) Roller cover (M1) King pin (A6) Front end plate (M2)-(M5) Bearings, cpl. (A7) Rear end plate (E3.2) Slip-ring assembly, centre part (A8,A9) Hex. screw, spring washer (E7) Cable tube (A15) Hoist (E8) Cable supporting tube (E10) Clips 2 Note: In order to safely position the jib, use two trestles (H2). If necessary,
additionally use squared timber (H3).
3.2 Jib pre-assembly
A8,A9
E3.2
A3
M4
M1
M2
A7
A4
M3
M5
H3
A2
H2
H5 K1
A6
A8,A9
H2
12 / 42 M_Meister_Hauptanleitung_EN10.06
3.2.1 Align the jib (A1) in the horizontal position.
3.2.2 Place jib (A1) on suitable trestles (H2) and / or (H3)
3.2.3 Secure the jib (A1) with a clamp (H5) or similar tools against tilting.
3.2.4 Remove front plate (A6), insert hoist unit (A15), and attach front plate (A6).
3.2.5 Mount the trolley end stops (K1)
- Observe instructions (refer to item 5)
- Precisely adjust runways. - Do not exceed rated outreach.
3.2.6 Position hoist unit (A15) in the front trolley area.
3.2.7 Remove any dirt from king pin (M1), put on bearing cover (M2), bearing (M3) and shim (M4) onto the king pin (M1) and secure by means of the retaining ring (M5) . (Items (M1) - (M5) are factory-assembled and packed in oiled paper.)
3.2.8 Mount the body of the slip ring assembly (E3.2) (see also item 12).
Note: For the pre-assembly of the jib and the completing works, the hoist unit can also be positioned at the other jib end next to the jib supporting beam.
13 / 42 M_Meister_Hauptanleitung_EN10.06
4. Jib completion 4.1 Items:
(B3) Type plate (E7) Cable tube (B4) SWL plate (E8) Cable supporting tube (B5) Danger strip (E10) Clips 2
4.2 Jib completion
4.2.1 Attach type plate (B3), SWL plate (B4) and danger strip (B5) on both sides of the jib.
4.2.2 Fasten the cable tube (E7) and cable supporting tube (E8) with clips (E10) on the jib (A1) (only for crane model with round power cable).
4.2.3 Fasten cable tube (E7) with clips (E10) on the bottom flange of the jib (A1) and on
the front plate of the jib support (A2) with clips (E10) (only for crane model featuring drive A).
4.2.4 Attach roller cover (A5), if any.
A1M6
E4
B3 B4 B5
E8,E10E7,E10
H3
H5
H2
A3
A4
A8,A9
A7
E3.2
E7,E10
A2
K1
A5.1: Dl<=430mm
A5.2: Dl>=530<=730mm
A5.3: Dl>=830<=1100mm
14 / 42 M_Meister_Hauptanleitung_EN10.06
5. Assembly instructions for trolley end stops
5.1 UNI trolley end stop (K1)
The UNI trolley end stop (trolley end stop) is exclusively suitable for: Girder sections featuring parallel flanges with thicknesses from 8 - 25 mm and
girder widths from 91 to 300 mm Load capacities as specified Travel speeds as specified
Load capacity (kg)
Max. perm. hoist weight (kg) Max. perm. approach speeds m/min
125 through 2000 180 28 2500 225 25 3200 225 22 4000 325 20 5000 600 16 6300 600 14 8000 1500 12 10000 1500 10
All components of the UNI trolley buffer are galvanized, the frame plates and clamping sections are additionally passivated and do not need any other corrosion protection.
For each slewing crane, two UNI trolley end stops (K1) are supplied. 5.1.1 Screw 2 locknuts (K1.7), 2 nuts (K1.5) and 2 washers (K1.6) onto threaded rod
(K1.4) towards the centre. Ensure even distribution on the right and on the left. 5.1.2 Place two frame plates (K1.1) on the right and on the left, as shown in the figure, on
threaded rod (K1.4) and push them into the girder section. 5.1.3 Push 2 clamping sections (K1.2), each, from the outside onto threaded rod (K1.4) and
tighten by hand, use washers (K1.6), nuts (K1.5) and locknuts (K1.7).
5.1.4 Attach the rubber end stops (K1.3) to the frame plate (K1.1), use hexagonal nuts (K1.3.1) and clamps (K1.3.2). If it is possible, position the end stops at the interface of frame and crossbeam of the hoist unit. (At this end 5 optional holes are available). Rubber end stops (K.1.3) are not required if trolleys are already fitted with rubber buffers. In such a case the trolley buffers may directly run against the frame plates of the UNI end stops (K1).
15 / 42 M_Meister_Hauptanleitung_EN10.06
5.1.5 When positioning the UNI-end stops (K1) on the boom, never exceed the nominal
outreach (=centre of the pillar up to final hook position). In any case, keep the minimum clearance of 10 mm between end of the jib and end stop.
5.1.6 Evenly tighten outer nuts (K1.5) on either side. Make sure that the frame plates (K1.1) are in contact with the girder edge.
5.1.7 Slightly tighten the inner nuts (K1.5) towards frame plate (K1.1). 5.1.8 Tighten outer nuts (K1.5) with a tightening torque of 35 Nm and secure with locknuts
(K1.7). 5.1.9 Tighten inner nuts (K1.5) with the same tightening torque and secure them as
described above. 5.1.10 If necessary, cut off protruding threaded rod (K1.4).
5.1.11 In order to test the fastening, move the hoist against UNI trolley buffer (K1).
Important!
The UNI safety end stop is important for safe operation. Therefore, regularly check the fastening of all items. If it is necessary, replace the fastening elements. In any case, the fastening of the end stop must be replaced when the end stop has reached the jib end.
Safety note:
If the failure of the UNI end stops presents a risk of personal injury, an additional safety item must be mounted (e.g. stop plate)!
A15
A1 K1
16 / 42 M_Meister_Hauptanleitung_EN10.06
Illustration: UNI end stops
Option: In order to reduce the length of projection of the beam, the frame plate can be deleted so that the front end stop can be directly attached to the jib end plate (A6). The special plate for this mounting option will be factory-preassembled.
K1.1
K1.2
K1.3 K1.3.1 K1.3.2
K1.4
K1.5-K1.7K1.5
K1.6K1.7 K1.6K1.1
K1.5
K1.7
K1.2
K1.3 K1.3.1 K1.3.2
A6
17 / 42 M_Meister_Hauptanleitung_EN10.06
5.2 Trolley end stops (K2) mounted on the bottom side of the beam
The trolley end stop (K2) is suitable for the following applications:
o Girder sections with parallel flanges of any thickness o Carrying capacity up to 10000 kgs o Travel speeds up to 20 m/min.
5.2.1 Attach both rubber stops (K2.5) by means of the spring washer (K2.6) and the nut
(K2.7) to the angle iron (K2).
5.2.2 Fasten the angle irons in the front and rear area, use screws (K2.1), washers (K2.2) and nut (K2.3) and secure screws with the locking nut (K2.4).. Note: The trolley end stops are factory-mounted on the beam! Option: In order to reduce the length of projection of the beam, the frame plate can be deleted so that the front end stop can be directly attached to the jib end plate (A6). The special plate for this mounting option will be factory-preassembled.
5.2.2
Katzfahrendanschlag unter dem Trägergurt
Trolley buffer attached to the bottom flange of the beam
K2 Winkelprofil K2 Angle
K2.1 Skt.-Schraube M16 K2.1 Hex.-screw M16
K2.2 Scheibe 17 K2.2 Washer 17
K2.3 Skt.-Mutter M16 K2.3 Hex.-nut M16
K2.4 Sicherungsmutter M16 K2.4 Securing nut M16
K2.5 Gummipuffer K2.5 Buffer
K2.6 Federring A10 K2.6 Spring washer A10
K2.7 Skt.-Mutter M10 K2.7 Hex.-nut M10
A6
K2.6 K2.7
K2.5
A6
K2.1
K2.2
K2
K2.2
K2.3
K2.4
K2.5-K2.7
18 / 42 M_Meister_Hauptanleitung_EN10.06
5.3 Trolley end stop (K3) attached to the beam web
5.4 The trolley end stop (K3) is suitable for the following applications:
o Girder sections with parallel flanges of any thickness o Carrying capacity up to 10000 kgs o Travel speeds up to 20 m/min.
5.4.1 Attach both rubber stops (K3.5) by means of the spring washer (K3.6) and the nut (K3.7) to the angle iron (K3).
5.4.2 Fasten both front angle irons (K3) with screws (K3.1), washers (K3.2) and nuts
(K3.3) and secure the screws with counternuts (K3.4). (The angle irons in the rear area are already factory-welded). Note: The trolley end stops on the beam are factory-assembled).
Option: In order to reduce the length of projection of the beam, the frame plate can be deleted so that the front end stop can be directly attached to the jib end plate (A6). The special plate for this mounting option will be factory-assembled.
Katzfahrendanschlag im Trägergurt
Trolley end stop mounted at the web
K2 Winkelprofil K2 Angle K3.1 Skt.-Schraube M16 K2.1 Hex.-screw M16 K3.2 Scheibe 17 K2.2 Washer 17 K3.3 Skt.-Mutter M16 K2.3 Hex.-nut M16 K3.4 Sicherungsmutter M16 K2.4 Securing nut M16 K3.5 Gummipuffer K2.5 Buffer K3.6 Zyl.-Schraube M10 K3.6 Cyl.-screw M10 K3.7 Federring A10 K2.6 Spring washer A10 K3.8 Skt.-Mutter M10 K2.7 Hex.-nut M10
K3.1
K3.2
K3.3
K3
K3.2
K3.4
K3.5-K3.8
K3.5K3.6 K3.7 K3.8
A6
19 / 42 M_Meister_Hauptanleitung_EN10.06
Overview of electrical components General E1
Supply cable, round – Round power supply cable – Round trailing power supply cable – Flat trailing power supply cable (or ideal control) with slip-ring
assembly – Flat trailing power supply cable (or ideal control) with limit
switches for limited slewing range
E1
Supply cable, flat – Flat trailing power supply cable (or ideal control) for limited
slewing range E2
Flush-mounted mains connection switch – 400 / 500 V 50 Hz – 20 A / 32 A / 100 A (depending on hoist) – lockable in 3 positions
E3
Slip-ring assembly – For infinite slewing range – 400 / 500 V 50 Hz – 16 A / 25 A / 100 A (depending on hoist)
E4
Twist-type cable entry gland – Protection of the supply cable for leading it through the king
pin
E5
Earthing lead – Earthing lead of pillar and jib
E6
Cable ties with eye
Support of the supply cable for infinite slewing range
20 / 42 M_Meister_Hauptanleitung_EN10.06
Round power supply cable E7
Cable tube – Guide for the supply cable parallel in jib up to cable
supporting tube – Length adapted to jib
E8
Cable supporting tube – Return of supply cable vertically to jib fitted on the
jib – Length: 500 mm
E9
Clips 1 – Fastening of cable tube on upper flange of jib
(application in jib) – for girders up to IPE 360
E10
Clips 2 – Fastening of cable tube on upper flange of jib – Application either in jib or on girder flange – for girders from IPE 400
E10
Clips 2 (option for cranes featuring slewing drives) – Fastening of cable tube on bottom flange of jib or jib
support – Application optionally in the jib or on girder flange – Power supply cable for drive type A
E11
Clips 3 – Fastening of cable supporting tube on jib Cable supporting tube projects the girder at both sides
21 / 42 M_Meister_Hauptanleitung_EN10.06
Round trailing power supply cable E12
Supporting arm – Bracket for rope guide – Fastening with clamp, flat on end plates
E13
Supporting arm (alternative mounting) – Bracket for rope guide – Fastening in rear jib area with hex. screws – Arrangement in girder
E14
Clamp, flat – Fastening of supporting arms on front and rear end
plates – 2 off/supporting arm
E15
Cable ties – Fastening of supply cable on supporting arms
E16
Eye bolt – Fastening of rope on supporting arm
E17
Rope – Running rope for round cable carriage, dia. 3 mm
E18
Ferrule – Fastening of rope on eye bolt
E19
Round cable carriage Guide of supply cable Max. SWL: 3 kg/carriage
The delivery of electrical items is customized to the crane design. It may deviate from the components specified in this list. Electrical installation works must be done by qualified personnel. In case of questions related to the installation of the electrical equipment, please contact your supplier.
22 / 42 M_Meister_Hauptanleitung_EN10.06
6. Round power supply cable (with cable supporting tube)
6.2 The cable tubes (E7) supplied must be cut to length to suit the jib.
Cable tube (E7) and cable supporting tube (E8) are mounted on the right-hand
side on the jib, viewed from the pillar in the direction of the jib end.
6.3 Pull supply cable (E1) with twist-type cable entry gland (E4) through the king pin hole.
6.4 Fix clips (E9 or E10) on the upper girder flange.
6.5 Insert cable tube (E7).
6.6 Fasten the cable supporting tube (E8) with clips (E11) in the middle between the
trolley end stops on the upper girder flange.
6.7 Pull the supply cable (E1) through the cable tube (E7) and the cable supporting tube (E8).
6.8 Leave the cable long enough, so it will not restrict the travel path of the hoist.
Note: Cable supporting tube (E11) must be arranged so that the supply cable (E1) does not rub against the jib or the hoist!
6.8 Connect supply cable (E1) with the hoist (A15) as shown on the circuit diagram.
E1
E9,E10
E7
E8
E11
E11
23 / 42 M_Meister_Hauptanleitung_EN10.06
7. Round power supply cable (with cable tensioning rope)
7.1 Fasten support brackets (E12) on the front end plate (11) and on the rear plate (12) with clamps (E14).
The support brackets (E12) are arranged on the right-hand side on the jib, viewed
from the pillar in the direction of the jib end. The support brackets (E12) are situated on the top of the jib. For a travel mechanism featuring a motorized trolley, mount the motor on the left-
hand side of the jib, i.e. opposite to the support brackets.
7.2 Pull supply cable (E1) with twist-type cable entry gland (E4) through the king pin hole and slide into rear supporting arm (E12).
Fasten supply cable (E1) on rear supporting arm (E12) by means of cable ties (E15).
7.3 Slide round cable carriages (E19) onto rope (E17).
Place the rope (E17) parallel to the jib.
7.4 Lead rope (E17) on both ends through ferrule (E18), the eye of eye bolt (E16) and through ferrule (E18). Compress ferrules (E18) with pliers.
7.5 Tension rope (E17) between front and rear supporting arms (E12) with eye bolt (E16).
7.6 Pull supply cable (E1) through round cable carriages (E19).
7.7 Fix supply cable (E1) and apply in loops through round cable carriages (E19) so that
the hoist can be travelled up to the tip of the jib. It must still be possible to move supply cable (E1) in this position.
Note: Rope (E17) must be arranged so that neither round cable carriages (E19) nor supply cable (E1) wear against the jib or the hoist!
7.8 Connect supply cable (E1) with the hoist unit (A15) as shown on the circuit diagram.
24 / 42 M_Meister_Hauptanleitung_EN10.06
A6
A7
E12
E14
E14
E14E12
E17E19
E18 E16
E12
E15
E16E18
E19
E1 E17
E12E17
E1
A15
25 / 42 M_Meister_Hauptanleitung_EN10.06
8. Final jib assembly
8.1 Loosen the rear end plate (A7).
8.2 Clean and grease the bearing seat in the top plate (S4) and the bearing (M3).
8.3 Attach the jib (A1) with a gradient of approx. 1 – 2° and position it above the pillar (S1).
8.4 Slowly lower the jib (A1).
Insert the bearing (M3) and position it onto the bearing seat by hand. Observe exact vertical line. Make sure that the bearing (M3) is not skewed. If it is necessary, use the pointed tool or other auxiliary means to correctly position the bearing. Avoid any contact of the slip ring assembly (E3) (if available) with structural items.
8.5 Fasten the rear end plate (A7) with a screw (A8) and a spring washer (A9).
A7
A8
A9
S1
A2
A15
H4 H5
A1
H1
Depending on the design and the features of the slewing crane, the assembly of the jib (A1) and the installation of the bearing (A3) can be facilitated by changing the position of the hoist unit (A15), i. e. the centre of gravity on the jib. Secure the hoist (A15) against any displacement during these installation activities!
26 / 42 M_Meister_Hauptanleitung_EN10.06
8.6 Fastening of the safety ring/strip (A11)
Note:
A safety ring or safety belt must be applied if the crane features a slewing drive "A". a jib locking device is provided. special mechanical slewing end stops are provided. the crane is used outdoors. the crane is located in the area of a bridge crane.
We recommend using this safety device if the crane is located below a bridge crane and the risk of collision exists due to improper handling of the bridge crane.
Option 1 Safety ring
Option 2 Safety strip
A12
A13 A12
A13A14 A12
A13A11.2
A11.1
27 / 42 M_Meister_Hauptanleitung_EN10.06
9. Precise alignment of pillar and jib
9.1 The pillar and the jib are precisely aligned by adjusting nuts (V2) and (V5) (see illustration
page 9). Attention: In order to avoid that only one anchor bolt gets under excessive strain during the alignment, adjust all neighbouring adjusting nuts (V2) accordingly!
9.2 Jib (A1) and pillar (S1) shall be aligned in such a way that the jib stops automatically in any
slewing position, it shall not slew on its own. (As a result of this alignment, the pillar may no longer stand vertically).
9.3 After the alignment, tighten upper nuts (V5) with a torque of Ma=100 Nm.
Note: Once proper alignment has been achieved, immediately proceed to underfill the foot flange! (see also item 14)
9.4 How to proceed to check crane alignment
9.4.1 Travel the hoist in the final front position.
9.4.2 Lower the hook to a specific height and provide a horizontal mark on the hook fittings (During the
entire measuring session, the position of hoist and load hook remains unchanged to not alter the measurement).
9.4.3 Perform a complete slewing motion to determine any deviation of the laser on the marking.
The admissible height deviation is maximum:
adm HA = 2 x outreach 1000
This means that for an outreach A being A = 4000 mm , the determined height for a slewing range being 180° may be max. 8 mm between highest and lowest point.
28 / 42 M_Meister_Hauptanleitung_EN10.06
10. Installation of electrics without slip-ring unit
10.1 Leave supply cable (E1) hanging loose in the tube.
10.2 Fasten the earthing wire / protective earth conductor (E5) on the retaining plate (S7).
10.3 Fasten the supply cable (E1) without the strain on retaining plate (S7) with cable ties with eye (E6) and leave it hanging in the tube.
10.4. Cover the opening (S6).
E1
E5
E1
S6
S7
29 / 42 M_Meister_Hauptanleitung_EN10.06
11. Installation of electrics with slip-ring unit
11.1 Connect the supply cable (E1) on the slip-ring side part (E3.1).
11.2 Fasten the slip-ring side part (E3.1) onto the centre of the the slip-ring unit (E3.2) through the access hole and bolt to retaining plate (S7).
11.3 Attach the supply cable (E1) without the strain on retaining plate (S7) with cable ties
with eye (E6) and leave it hanging in the tube.
11.4 Cover the opening (S6).
E1
E3
E6
E1
S6
S7
M6
30 / 42 M_Meister_Hauptanleitung_EN10.06
12. Assembly of the slip-ring unit
A slip-ring unit is used for an unlimited slewing range (the jib slewing motion is infinite).
12.1 Dismantle the centre part (E3.2) of the slip-ring unit (E3).
12.2 Lead the supply cable (E1) and the earthing cable (E5) through the centre part of slip-
ring (E3.2).
12.3 Strip the insulation from supply cable (E1) for approx. 100 mm.
12.4 Fasten the earthing cable (E5) 1 x 4 mm² as well as the protective earth conductor on the protective earth ring (E3.8).
12.5 Connect the other three pole rings (E3.9).
12.6 Re-assemble centre part of slip-ring (E3.2).
E3.8
E3.9
E3.2 Insulator
Pole ring E3.9
Disc
Washer
Spring washer
Hexagonal nut
Insulator
Threaded rod
Tube
31 / 42 M_Meister_Hauptanleitung_EN10.06
12.7 Pull supply cable (E1) and earthing cable (E5) through the king pin (M1) and twist-type cable entry gland (E4).
12.8 Fasten the centre part of slip-ring (E3.2) on the king pin (M1).
The centre part of the slip-ring unit (E3.2) is attached to a special tube (M6) on
the king pin (M1). Fasten the two grub screws (E3.7) to the centre part of slip-ring (E3.2). Secure the two grub screws (E3.7) with an hexagonal nut (E3.6).
12.9 Screw the hexagonal nuts (E3.4) onto eye bolts (E3.3) and tighten up to the middle.
12.10 Slide the isolating sections (E3.5) onto the eye bolts (E3.3) and fasten eye bolts
(E3.3) in the side part of slip-ring (E3.1).
Note: The thread of eye bolts (E3.3) must not project from the side part!
Position/ Item
Anzahl/ Amount
Benennung Designation
Schleifringkörper Slipring collector
E3.1 1 Seitenteil Side part E3.2 1 Mittelteil Middle part E3.3 2 Augenschraube
M8x60 Eye screw M8x60
E3.4 2 Skt.-Mutter M8 Hex.-nut M8 E3.5 2 Isolierstück Isolator E3.6 2 Skt.-Mutter M6 Hex.-nut M6 E3.7 2 Madenschraube
M6x16 Set screw M6x16
E3.8 1 Schutzleiterring Earthing ring E3.9 3 Polring Pole ring
E3.1
E3.2E3.3 E3.4 E3.5 E3.7 E3.6
E3.8
E3.9
E3.1E3.2
E3.3E3.4 E3.5
E3.6 E3.7
E3.2
E3.1
32 / 42 M_Meister_Hauptanleitung_EN10.06
13. Electrical installation of the mains connection switch 13.1 Pull cable (H1) and supply cable (E1) through the switch opening (S8). 13.2 Fix the earthing wire onto the earthing terminal (E2.1) on the tube and of the flush-
mounted mains connection switch (E2). 13.3 Pull cables (E1 and H1) through the protecting sleeve (E2.3). 13.4 Strip the insulation from the cable wires and connect them to the switch terminal (E2.2). 13.5 Fit the mains connection switch (E2). 13.6 For cranes operated outdoors, the cable openings of the earth and supply cables in the jib
must be sealed additionally. 13.7 Carefully check all crane functions without load after the completion of the installation.
Ensure that the rotating field of the crane turns clockwise.
E1
S8
E2.3
E2.1
E2.2 E2
H1
33 / 42 M_Meister_Hauptanleitung_EN10.06
14. Slewing end stop
If it is necessary, mechanical end stops (SM1/SM2) can be provided to limit the slewing range.
14.1 Installation of the end stops - standard slewing range
14.1.1 Attach the rubber buffers to the end stops (SM1/SM2). The mounting bracket (SM5) situated on the jib support (A2) is factory-assembled.
14.1.2 Slew the jib (A1) in the end positions, keep end stop (SM1) in contact with the mounting
bracket (SM5) on the jib boom (A2) and mark the position. 14.1.3 Return the jib (A1) in its initial position. 14.1.4 Weld the end stop (SM1) on the pillar (S1)
(If it is necessary, remove the rubber buffers!)
14.1.5 Optionally, the end stop (‚SM2) can be fastened on the pillar (S1) with screws: o Proceed as described under 14.1.1 through 14.1.3 o Cut thread M12 in the pillar (S1) o Fasten end stop (SM2) with the hexagonal screw (SM3) and a spring washer (SM4)
14.1.6 Test the end stops (SM1/SM2) by slewing the jib (A1), check fastening and position of the
end stops, if it is necessary, re-align the end stops.
Unit / Pitch circle Dl
Slewing rang maximum
200 / 330 mm approx. 245° 300 / 430 mm approx..280° 400 / 530 mm approx. 280° 500 / 630 mm approx. 295° 600 / 730 mm approx. 295° 700 / 830 mm approx. 295° 800 / 930 mm approx. 305°
1000 / 1100 mm approx. 315°
A2
SM5
S1SM1 SM2
SM1
SM5
SM2
SM3
SM4
34 / 42 M_Meister_Hauptanleitung_EN10.06
14.2 Installation of the end stops - maximum slewing range
The mechanical slewing end stops (SM1/SM2) can be positioned in such a way that the maximum slewing rang is utilized.
Proceed to the mounting of the slewing end stops (SM1/SM2) as follows:
o Attach two mounting brackets (SM5), one above the other, to the pillar o Position the end stops (SM1/SM2), one above the other, and align them with
the mounting brackets (SM5)
14.2.1 Fasten the rubber buffers on the end stops (SM1/SM2). The mounting brackets (SM5) are factory-assembled on the jib support (A2).
14.2.2 Slew jib (A1) in the end positions of end stop (SM1) on the upper bracket (SM5) and
end stop (SM2) on the bottom bracket (SM5) on the pillar (A2) and mark the positions.
14.2.3 Return the jib (A1) in its initial position. 14.2.4 Weld end stops (SM1) to the pillar (S1)
(if it is necessary, remove the rubber buffers!)
14.2.5 Optionally, the end stop (SM2) can be fastened on the pillar (S1) with screws: o Proceed as described under 14.2.1 through 14.2.3 o Cut thread M12 in the pillar (S1) o Fasten end stop (SM2) with hexagonal screw (SM3) and spring washer (SM4)
14.2.6 Test the end stops (SM1/SM2) by slewing the jib (A1), check fastening and position of the end stops, if it is necessary, re-align the end stops.
35 / 42 M_Meister_Hauptanleitung_EN10.06
Unit / Pitch circle Dl
Slewing range maximum
200 / 330 mm approx. 300° 300 / 430 mm approx. 320° 400 / 530 mm approx. 320° 500 / 630 mm approx. 330° 600 / 730 mm approx. 330° 700 / 830 mm approx. 330° 800 / 930 mm approx. 340°
1000 / 1100 mm approx. 345°
36 / 42 M_Meister_Hauptanleitung_EN10.06
15. Undergrouting and anchorage (system ANKERFIX)
For slewing jib base plates which are fastened with anchor bolts concrete footing must be provided!
15.1 Only proceed to pour the concrete after complete assembly and precise alignment of the jib (see item 9). Underfill the foot flange immediately after the precise alignment of the slewing crane!
15.2 The foot flange undergrouting must be done with utmost care:
o The entire surface of the crane base must be underfilled (pouring the material just around the crane base is insufficient and inadmissible)
o The crane base shall not be completely covered in order to still allow the inspection of anchor bolts.
o Minimum concrete quality: class B25 (DIN1045) or C20/25 (DINEN206-1)
15.3 ATTENTION! Only tighten the anchor nuts (V5), test the load capacity and put the crane into operation after complete concrete hardening (after 28 days according to DIN standards). The use of fast drying binder (e. g. PCI grouting mortar 50) may reduce the time before the crane’s acceptance test, if it is provided.
In case the concrete hardening time will not be respected, it may result in an excessive deflection and overloading of crane components.
15.4 When the undergrouting is drying, a small air gap (not perceptible in most of the cases) may form between the crane’s foot flange (S2) and the undergrouting due to the concrete shrinking U-shaped plates (V4) under the foot flange (S2) help filling this gap and help producing a direct tension load on the anchor bolts (V1) keeping them free of alternating stress.
15.5 How to proceed - Leave crane jib unloaded - Position hoist close to the pillar
15.5.1 Tighten all anchor nuts (V5) with a torque of Ma=400Nm by means of a torque key (A)
15.5.2 Consistently and slightly loosen the anchor nuts (V5) (approx. by 30° to 45°) (B)
15.5.3 Tighten all anchor nuts (V5) with a torque of Ma=300Nm by means of a torque key (C)
15.5.4 In a second turn re-tighten again all anchor nuts (V5) with a torque of Ma=300Nm (D)
15.5.5 Additionally, secure all anchor nuts (V5) with locking nuts (V6)
15.5.6 Outdoors, the perimeter of the crane base (S2) shall be permanently sealed (e. g. with silicone)!
A 400 Nm B 30°-45° C 300 Nm
D 300
37 / 42 M_Meister_Hauptanleitung_EN10.06
Illustration: Fixation with anchor bolts; after completing the undergrouting
38 / 42 M_Meister_Hauptanleitung_EN10.06
16. Putting into operation
16.1 Once the installation is completed and prior to start the crane operation the following tests need to be performed in compliance with §19 of the EN 60204-32 have to be carried out: 1. test run 2. test of earthing conductors 3. measurement of the insulating resistance
16.2 The crane and its fastening elements must remain permanently accessible for inspections. 16.3 When putting the crane into operation, coating material (zinc, paint) may accumulate on
the running surfaces of the jib beam which prevent the smooth run of the trolleys. The dirt must be removed.
16.4 Inspections prior to putting the crane into operation (in compliance with the accident prevention regulations UVV BGV D6)
An inspection has to be performed on cranes before putting them into operation.
The owner (operator) must ensure that cranes are inspected before being put into service for the first time by:
a) Expert engineers (authorized crane expert engineers)
Acceptance test of crane installations in acc. with DIN 15030 and UVV BGV D6 (BGG 905) cranes, test load and lifting attachments must be provided by the customer. The following crane models are subject to inspections by expert engineers:
all cranes with a capacity 1000 kg all cranes with two or more powered motions.
b) Qualified technicians The following cranes must be checked by qualified technicians:
all other cranes not checked by expert engineers
16.5 Routine inspections
Depending on the local and on the operating conditions, the owner must ensure that cranes are inspected as required, at least once a year, by a qualified crane expert.
39 / 42 M_Meister_Hauptanleitung_EN10.06
17. Technical information
17.1 Tightening torques for fastening elements
The fastening elements for the crane base must be pre-tensioned with specified tightening torques.
The following table shows the most important tightening torques.
17.1.1 M27 anchor bolt, to DIN 1045, greased (special production of special quality for crane foundation)
Tightening torque: 300 Nm
17.1.2 HT bolts to DIN 6914, black, slightly greased
Thread size Screw quality Tightening torque
M 16 10.9 284 Nm M 20 10.9 554 Nm M 24 10.9 958 Nm M 27 10.9 1420 Nm
17.1.3 Hex. bolts to DIN 931, DIN 933 and threaded rods DIN 976, galvanized, lubricated with MoS2
Thread size Screw quality Tightening
torque M 16 8.8 179 Nm M 20 8.8 350 Nm M 24 8.8 604 Nm M 27 8.8 900 Nm
17.1.4 M16 anchor bolt, galvanized, lubricated with MoS2
17.1.5 M12 anchor bolts a) UVM dyn 100 M12/50: tightening torque: 40 Nm b) HVZ dynamic M12/50: tightening torque: 50 Nm
17.2 Safety distances (As specified in the relevant accident prevention regulations)
Safety distances in accordance with UVV Cranes BGV D6), §11 and §32 A minimum distance of 150 mm is required for the installation.
40 / 42 M_Meister_Hauptanleitung_EN10.06
18. Spare parts list
Please provide the following information with your spare parts order:
Crane type Serial number of the crane Year of manufacture.
The spare parts listed below are only some of the standard components For spare parts of the hoist and the electrical slewing drives, please refer to the separate spare parts lists.
18.1 Mechanical components
Component pitch circle Dl
200 / dia. 330
King pin bearing Dl 330
Support washer Dl 330
Seeger ring Dl 330
Nilos ring Dl 330
Thrust roller Dl 330
Thrust roller bearing Dl 330
Seeger ring inside Dl 330
Seeger ring outside Dl 330
- Thrust roller cover sheet metal box Dl 330
Access hole cover dia. 125
300 / dia. 430
King pin bearing Dl 430
Support washer Dl 430
Seeger ring Dl 430
Nilos ring Dl 430
Thrust roller Dl 430
Thrust roller bearing Dl 430
Seeger ring inside Dl 430
Seeger ring outside Dl 430
- Thrust roller cover sheet metal box Dl 430
Access hole cover dia. 160
400 / dia. 530
King pin bearing Dl 530
Support washer Dl 530
Seeger ring Dl 530
Bearing cover plate Dl 530
Thrust roller Dl 530
Thrust roller bearing Dl 530
Seeger ring inside Dl 530
Seeger ring outside Dl 530
Support washer Dl 530
Thrust roller cover Plastic Dl 530
Access hole cover dia. 160
500 / dia. 630
King pin bearing Dl 630
Support washer Dl 630
Seeger ring Dl 630
Bearing cover plate Dl 630
Thrust roller Dl 630
Thrust roller bearing Dl 630
Seeger ring inside Dl 630
Seeger ring outside Dl 630
Support washer Dl 630
Thrust roller cover Plastic Dl 630
Access hole cover dia. 160
600 / dia. 730
King pin bearing Dl 730
Support washer Dl 730
Seeger ring Dl 730
Bearing cover plate Dl 730
Thrust roller Dl 730
Thrust roller bearing Dl 730
Seeger ring inside Dl 730
Seeger ring outside Dl 730
Support washer Dl 730
Thrust roller cover Plastic Dl 730
Access hole cover dia. 160
700 / dia. 830
King pin bearing Dl 830
Support washer Dl 830
Seeger ring Dl 830
Bearing cover plate Dl 830
Thrust roller Dl 830
Thrust roller bearing Dl 830
Seeger ring inside Dl 830
Seeger ring outside Dl 830
Support washer Dl 830
Thrust roller cover Plastic cap Dl 830
Access hole cover dia. 160
800 / dia. 930
King pin bearing Dl 930
Support washer Dl 930
Seeger ring Dl 930
Bearing cover plate Dl 930
Thrust roller Dl 930
Thrust roller bearing Dl 930
Seeger ring inside Dl 930
Seeger ring outside Dl 930
Support washer Dl 930
Thrust roller cover Plastic cap Dl 930
Access hole cover dia. 160
1000 / dia. 1100
King pin bearing Dl 1100
Support washer Dl 1100
Seeger ring Dl 1100
Nilos ring Dl 1100
Thrust roller Dl 1100
Thrust roller bearing Dl 1100
Seeger ring inside Dl 1100
Seeger ring outside Dl 1100
Support washer Dl 1100
Thrust roller cover Plastic cap Dl 1100
Access hole cover dia. 160
Qty. fitted 1 1 1 1 2 Dl330-430: 2
Dl530-1100: 4 2 2 2 Sheet metal box: 1
Plastic: 2 1
Item as in erection instructions
M3 M4 M5 M2 A4 Fitted in A4 Fitted in A4 Fitted in A4 Fitted in A4 A5 S6
41 / 42 M_Meister_Hauptanleitung_EN10.06
18.2 Mechanical slewing stop
Component Pitch circle 200 / dia. 330
Round buffer dia. 30 x 30 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
300 / dia. 430
Round buffer dia. 30 x 30 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
400 / dia. 530
Square buffer 30 x 40 x 60 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
500 / dia. 630
Square buffer 30 x 40 x 60 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
600 / dia. 730
Square buffer 30 x 40 x 60 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
700 / dia. 830
Square buffer 60 x 60 x 150 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
800 / dia. 930
Square buffer 60 x 60 x 150 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
1000 / dia. 1100
Square buffer 60 x 60 x 150 cpl. with fastening elements
Slewing stop angle bracket, weldable
Slewing stop angle bracket, screw-type cpl. with fastening elements
Qty. fitted 2 2 2 Item as in erection instructions
Fitted on SM1,SM2 SM1 SM2
42 / 42 M_Meister_Hauptanleitung_EN10.06
18.3 Electrical components
Component Pitch circle
All Mains connection switch
Slip-ring assembly
C-rail S1 (1,5 mm) C-rail S1 (2,0mm) Fixed suspension
Connector Rail end cable clamp
Flat cable carriage
Towing trolley
Clamp, round End cap
Qty. fitted 1 1 Depends on outreach
Depends on outreach
Depends on outreach
Depends on outreach
1 Depends on outreach
1 Depends on outreach
1
Item as in erection instructions
E2 E3 E12,E13,E20,E21 E12,E13,E20,E21 E25 E23 E27 E36 E28 E24 -
All End stop Ideal control
carriage for direct control
Ideal control carriage for contactor control
Wire rope with ferrules
Round cable carriage
Cable supporting tube cpl.
Clips Clamp, flat
Qty. fitted 1 1 1 1 Depends on outreach
1 Various Various
Item as in erection instructions
E34 E32 E33 E17,E18 E19 E8 E9,E10,E11 E14
top related