Transcript
7/30/2019 Electrical Circuits Simulation
1/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 1
VERIFICATION OF
SUPERPOSITION AND
RECIPROCITY THEOREMS
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
2/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 2
Experiment no: Batch no: Date:
VERIFICATION OF SUPERPOSITION
& RECIPROCITY THEOREMS
AIM : To verify Superposition & Reciprocity theorems for the given network.
APPARATUS :
THEORY:-
I. Superposition Theorem Statement:
In a linear network with several independent sources which includeequivalent sources due to initial conditions and linear dependent sources, the overallresponse in any part of the network is equal to the sum of the individual responses due
to each independent source, considered separately, with all other independent sourcesreduced to zero.
Note: 1. The sources which are considered one at a time making all other sources zero,
are the independent sources including sources due to initial conditions only. Thedependent sources are retained as they are in the network.
2. When one independent source is considered & all other independent sourcesare reduced to zero means that all the other independent voltage source are replaced with
short circuit and all the other independent current sources are replaced with open circuit.If the sources contain internal impedances, that sources are replaced by their internal
impedances.
II. Reciprocity Theorem Statement:
The Reciprocity theorem states that the ratio of response to excitation isinvariant to an interchange of the position of the excitation and response in a singlesource network. However if the excitation is a voltage source, the response should be acurrent and vice versa.
S. No Name of Apparatus Type Range Quantity
1 Voltmeter PMMC 0-300V 2
2 Ammeter PMMC 0-2.5A 1
3 RheostatWWWW
WW
WW
50/5A110/2A
300/1.7A
300/2A
21
1
24. Fuse TCC 5A 4
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
3/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 3
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
4/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 4
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
5/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 5
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
6/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 6
PROCEDURE:-
I. SUPERPOSITION THEOREM:
1. Connect the circuit as per the Circuit diagram.
2. Close Switch S1 on to the Supply mains & remain Switches S2 & S3 open and
Switch S4 closed.3. Note down the Voltmeter readings V1 ,V2 & Ammeter reading as I' in the S.No1
of Table14. Now close Switch S2 on to the Supply mains & remain Switches S1 & S4 open and
Switch S3 closed.5. Note down the Voltmeter readings V1 ,V2 & Ammeter reading as I" in the S.No2
of Table16. Now Close Switches S1 & S2 on to the Supply mains & remain Switches S3 &
S4 open.7. Note down the Voltmeter readings V1 ,V2 & Ammeter reading as I in the S.No3
of Table1
8. Finally disconnect the circuit from the Supply mains by open all the Switches.
II. RECIPROCITY THEOREM:
CASE : I
1. Connect the circuit as per the Circuit diagram.
2. Close Switch S1 on to the Supply mains3. Note down the Voltmeter V1& Ammeter A1 readings in S. No. 1 of Table 2
4. Disconnect the circuit from the Supply mains by opening the Switch S1.
CASE : II
1. Connect the circuit as per the Circuit diagram.2. Close Switch S2 on to the Supply mains
3. Note down the Voltmeter V2 Ammeter A2 readings in S. No. 2 of Table 24. Disconnect the circuit from the Supply mains by opening the Switch S2.
OBSERVATION TABLE:-
TABLE 1
S.No. Voltmeter Reading Voltmeter Reading Ammeter Reading
1. V1 = V2 = I' =
2. V1 = V2 = I" =
3. V1 = V2 = I =
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
7/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 7
TABLE 2
S.No. Voltmeter Reading Ammeter Reading
1. V1 = I1 =
2. V2 = I2 =
PRECAUTIONS:
1. Avoid Loose Connections.2. Readings must be taken without parallax error.
3. Before switching on the supply for the circuit, ensure that all rheostats are at maximumposition and during the experiment these should not be disturbed.
RESULTS:
I. SUPERPOSITION THEOREM:
Theoretical Practical1. I' =
2. I" =
3. I =
II. RECIPROCITY THEOREM:
Theoretical Practical
1. V1/ I1 =
2. V2/ I
2=
CONCLUSIONS:
VIVA QUESTIONS:
1) What are the Statements of the above theorems?2) What is a linear network?
3) Where the above theorems are used practically?4) What are the practical applications of the above theorems?
5) What is a bilateral network? Give examples.6) What are the limitations of above theorems?
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
8/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 8
VERIFICATION OF THEVENINS
NORTONS &MAXIMUM POWER
TRANSFER THEOREMS
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
9/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUTE OF ENGINEERIN G & TECH NOLOGY 9
Experiment no: Batch no: Date:
A) VERIFICATION OF THEVENINS
& NORTONS THEOREMS
AIM : To verify Thevenins & Nortons theorems for the given circuit.
APPARATUS:
S. No Name of Apparatus Range Type Quantity
1 Voltmeters 0-300V MI 2
2 Ammeter 0-2A MI 2
3 Rheostats
50 , 5A110 , 2A200 , 2A
WW
WWWW
2
11
4 1- Variac 230V / (0-270)V,15A
---- 1
5. SPST ---- ---- 2
6. Fuse 5A TCC 2
THEORY:-
I) Thevenins Theorem Statement:
Any combination of linear bilateral circuit elements and active sources,regardless of the connection or complexity, connected to a given load RL, may be
replaced by a simple two terminal network consisting of a single voltage source of Vthvolts and single resistance Rth in series with the voltage source, across the two
terminals of the load RL . The Vth is the open circuit voltage measured at the twoterminals of interest, with load resistance RL removed. This voltage is also called
Thevenins equivalent voltage. The Rth is the Thevenins equivalent resistance of thegiven network as viewed through the open terminals with RL removed and all the activesources are replaced by their internal resistances. I f the internal resistances are notknown then independent voltage sources are to be replaced by the short circuit whilethe independent current sources must be replaced by open circuit.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
10/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITU TE OF ENGIN EERING & TECH NOLOGY 10
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
11/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 11
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
12/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 12
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
13/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 13
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
14/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 14
II) Nortons Theorem Statement :
Any combination of linear bilateral circuit elements and active sources,regardless of the connection or complexity, connected to a given load RL, can bereplaced by a simple two terminal network, consisting of a single current source of I Namperes and a single resistance RN in parallel with it, across the two terminals of the
RL.The IN is the short circuit current flowing through the short circuited path, replacedinstead of RL. It is also called Nortons current. The RN is the equivalent resistance ofthe given network as viewed through the load terminals, with RL removed and all theactive sources are replaced by their internal resistances. If the internal resistances areunknown then the independent voltage sources must be replaced by short circuit whilethe independent current sources must be replaced by open circuit.
PROCEDURE:-
I) FOR CIRCUIT 1:
1. Connect the circuit as per the circuit diagram.2. Apply 230 V AC Supply to the Variac (with its variable position at 3C) by closing the
DPST Switch.
3. Gradually vary the variable position of the Variac until the Voltmeter1 reads 200 V.4. Note down the corresponding readings of Ammeter & Voltmeter2 in Table 1 with theconditions
i) SPST 1 Closed & SPST 2 Openii) SPST 1 Open & SPST 2 Open
iii) SPST 1 Closed & SPST 2 Closed5. Gradually vary the variable position of the Variac until the Voltmeter1 reads 0 volts
6. Disconnect the Variac from the supply by opening the DPST Switch.
II) FOR CIRCUIT 2:
1. Connect the circuit as per the circuit diagram.2. Apply 230 V AC Supply to the Variac (with its variable position at C ) by closing the
DPST Switch.3. Gradually vary the variable position of the Variac until the Voltmeter reads 150 V &
note down the corresponding reading of Ammeter in Table 2.4. Gradually vary the variable position of the Variac until the Voltmeter reads 0 volts
5. Disconnect the Variac from the supply by opening the DPST Switch
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
15/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 15
III) FOR CIRCUIT 3:
1. Connect the circuit as per the circuit diagram.
2. Apply 230 V AC Supply to the Variac (with its variable position at C ) by closing theDPST Switch.
3. Gradually vary the variable position of the Variac until the Voltmeter reads Vth , as
obtained in Table 14. Close the SPST Switch & vary the rheostat until the Ammeter reads current I forwhich Vth / I gives Rth , the value as obtained in Table 2 .
5. Once the Rheostat set to Rth , open the SPST Switch & note down the reading of theAmmeter in Table 3
6. Gradually vary the variable position of the Variac until the Voltmeter reads 0 volts7. Disconnect the Variac from the supply by opening the DPST Switch
IV) FOR CIRCUIT 4:
1. Connect the circuit as per the circuit diagram.
2. Use the same Rheostat which set to Rth as in the Circuit 33. Apply 230 V AC Supply to the Variac (with its variable position at C) by closing the
DPST Switch.4. After closing the SPST switch gradually vary the variable position of the Variac until
the Ammeter1 reads current IN as obtained in Table 1 & note down the correspondingreading of the Ammeter2 in Table 4.
5. Gradually vary the variable position of the Variac until the Voltmeter reads 0 volts6. Disconnect the Variac from the supply by opening the DPST Switch
OBSERVATION TABLE:-
TABLE 1 (For Circuit 1)
S.No Switch conditions Voltmeter V1 Voltmeter V2 Ammeter
1. SPST 1 ClosedSPST 2 Open
VS = VL = IL =
2. SPST 1 OpenSPST 2 Open
VS = Vth = IL = 0
3. SPST 1 ClosedSPST 2 Closed
VS = VL = 0 IN =
TABLE 2 (For Circuit 2)
S.No Voltmeter Ammeter Rth = VS / IS
1. VS = IS = Rth =
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
16/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 16
TABLE 3 (For Circuit 3)
S.No Voltmeter Ammeter
1. Vth = IL =
TABLE 4 (For Circuit 4)
S.No Ammeter I1 Ammeter I21. IN = IL =
PRECAUTIONS:-
1. Avoid loose connections.
2. Avoid Parallax error.3. Before switching on the supply for each circuit, ensure that all rheostats are at
maximum position and during the experiment these should not be disturbed.4. Variable position of the Variac (auto transformer) should be at minimum position
before switching on the power supply.
RESULTS:-Theoretical Practical
1. IL from the Main circuit =
2. IL from the Thevenins Equivalent Circuit =
3. IL from the Nortons Equivalent circuit =
CONCLUSIONS:-
VIVA QUESTIONS:-
1) What is the Statement of Thevenins theorem?
2) What is a linear network?3) What is a bilateral network?
4) What are Active & Passive elements?5) What are the applications of the above theorem?
6) What are the limitations of application of this theorem?
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
17/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 17
B) VERIFICATION OF MAXIMUM POWER
TRANSFER THEOREM
AIM : To verify Maximum Power transfer theorem for the given circuit.
APPARATUS:
S. No Name of Apparatus Type Range Quantity
1Voltmeter
MCMC
0-300V0-150V
11
2 Ammeter MC 0-2A 1
3 RheostatWWWW
WW
100/5A50/5A200/2A
21
1
4. Fuse TCC 5A 2
THEORY:
Statement: The Maximum Power transfer theorem states that A Resistance load RL,
being connected to a DC network, receives maximum power when it is
equal to the internal resistance of the source network as seen from the
load terminals i.e. Rth
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
18/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 18
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
19/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 19
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
20/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITU TE OF ENGIN EERING & TECH NOLOGY 20
With reference to Fig (B)
Lth
thL
RR
VI
+=
While the power delivered to the resistive load is
( )
( )L
Lth
thLLL R
RR
VRIP
+==
2
2
2
PL can be maximized by varying R and hence, maximum power can be delivered when
(dPL/dRL) = 0
( ) ( ) ( )
( )0
4
2222
=+
++
Lth
Lth
L
LthLth
L
Lth
RR
RRdR
dRVRV
dR
dRR
( ) ( ) ( )( )
02
4
222
=+
++
Lth
LthLththLth
RR
RRRVVRR
( ) 02 =+ LLth RRR
thL RR =
Hence it has been proved that power transfer from a dc source network to a resistivenetwork is maximum when the load resistance of the network is equal to the internal
resistance of the dc source
Again with RL=Rth, the system being perfectly matched for load and source,power transfer becomes maximum and this amount of power (Pmax) can be obtained as
( ) th
th
thth
thth
R
V
RR
RVP
4
2
2
2
max =+
=
The total power supplied is thus
th
th
th
th
inRV
RVP
242
22
==
During maximum power transfer the efficiency of the circuit becomes,.
%50100max ==in
P
P
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
21/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 21
PROCEDURE:-
I) TO FIND POWER VARIATIONS WITH RL
1. Connect the circuit as per the Circuit diagram 1.
2. Apply 220 V DC Supply to the circuit by closing the DPST Switch.
3. Note down the readings of Ammeter & Voltmeter in Table 1 which are connectedacross the load after keeping the load rheostat, RL at its minimum value.4. Increase the load resistance in steps and for each step, note down the corresponding
Ammeter and Voltmeter readings in Table 1.5. Disconnect the circuit from the supply by opening the DPST Switch.
II) TO FIND Rth
1. Connect the circuit as per the Circuit diagram 2.
2. Apply 220 V DC Supply to the circuit by closing the DPST Switch.3. Note down the readings of Ammeter & Voltmeter in Table 2.
4. Disconnect the circuit from the supply by opening the DPST Switch.
OBSERVATION TABLE:-
TABLE 1
S No VL (volts) IL (amps) RL = VL/ IL () PL = IL RL
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
22/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 22
TABLE 2
S No VS (volts) IS (amps) R th = VS/IS
1.
MODEL GRAPH:-
PRECAUTIONS:-
1. Avoid loose connections.
2. Avoid Parallax error.3. Take more number of readings for a better plot
RESULTS:-
1. Pmax = ----------
2. RL = ---------
3. Rth = ---------
4. = ---------
CONCLUSIONS:-
VIVA QUESTIONS:-
1) What is the Statement of Maximum Power Transfer theorem?2) What is a linear network?
3) What is a bilateral network?4) What are the applications of the above theorem?
5) What are the advantages & disadvantages of the above theorem?
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
23/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 23
DETERMINATION OF TWO
PORT NETWORK PARAMETERS
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
24/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 24
Experiment no: Batch no: Date:
DETERMINATION OF TWO PORT
NETWORK PARAMETERS
AIM: To determine Z, Y, ABCD and H parameters of a given two port Network.
APPARATUS:
S.No Specification Range Type Quantity
1 Voltmeter (0-300)V PMMC 2
2 Ammeter (0-5)A PMMC 2
3 Rheostat (50 , 5A) Wire Wound 3
4 Switches ------ DPDT 2
5 Fuses 5ATin Coated
Copper 2
6 Connecting Wires 1 Square mmInsulatedcopper
As perRequirement
THEORY:
A network containing two pairs of terminals is called as two port network.Normally one pair of terminals coming together to supply power or to withdraw power or
to measure the parameters, are called as port. To achieve simplicity, the whole network isshown with a single block.
A typical two port network is as shown below in fig (a)
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
25/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 25
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
26/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 26
OPEN CIRCUIT IMPEDANCE PARAMETERS (Z-parameters):
Z-parameters can be defined by the following equations
V1 = Z11I1 + Z12I2 (1)
V2 = Z21I1 + Z22I2 (2)
Matrix form:
( )3...............................2
1
2221
1211
2
1
=
I
I
ZZ
ZZ
V
V
If port 2-21
is open circuited, i.e. I2 = 0 then
Z11 = V1/I1 & Z21 = V2/I1
If port 1-11 is open circuited, i.e. I1 = 0, then
Z12 = V1/I2 & Z22 = V2/I2.
Here,
Z11 is the driving point impedance at port 1-11
with 2-21
open circuited. It can
also be called as open circuit input impedance.
Z21 is the transfer impedance at port 1-11
with 2-21
open circuited. It can also becalled as open circuit forward transfer impedance.
Z12 is the transfer impedance at port 2-21
with 1-11
open circuited. It can also be
called as open circuit reverse transfer impedance and
Z22 is the driving point impedance at port 2-21
with 1-11
open circuited. It can alsobe called as open circuit output impedance.
Z-parameter representation for a two port network, shown above, will be as
shown below in fig (b)
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
27/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 27
If the
Network is
a) Reciprocal then V1/I2 (where I1 = 0) = V2/I1 (where I2 = 0) i.e. Z12 = Z21
b) Symmetrical then V1/I1 (where I2 = 0) = V2/I2 (where I1 = 0) i.e. Z11 = Z22
SHORT CIRCUIT ADMITTANCE PARAMETERS (Y-parameters):
Y-parameterscan be defined by the following equations
I1 = Y11V1 + Y12V2 . (1)
I2 = Y21V1 + Y22V2 . (2)
In matrix form
( )3...............................2
1
2221
1211
2
1
=
V
V
YY
YY
I
I
If port 2-21 is short circuited, i.e. V2 = 0 then
Y11 = I1/V1 & Y21 = I2/V1
If port 1-11
is short circuited, i.e. V1 = 0 then
Y12 = I1/V2 & Y22 = I2/V2
1
2
I2I1
Z11
+
_
Z22
Z12I2 Z21I1
2
11
V2V1
Fig (b) Open circuit impedance parametric representation of a two port net work.
+
_
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
28/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 28
Here,Y11 is the short circuit driving point admittance at port 1-11
with 2-21
short circuited. It will also be called as short circuit input admittance.
Y21 is the Transfer admittance at port 1-11
with 2-21
short circuited. It willalso be called as short circuit forward transfer admittance.
Y12 is the Transfer admittance at port 2-21
with 1-1
1
short circuited. It willalso be called as short circuit reverse transfer admittance and
Y22 is the driving point admittance at port 2-21
with 1-11
short circuited. Itcan also be called as short circuit output admittance.
Y-parameter representation for a two port network, shown above, will be as
shown below
If the network is
a) Reciprocal then I2/V1 (where V2 = 0) = I1/V2 (where V1 = 0) i.e. Y21 = Y12
b) Symmetrical then I1/ V1 (where V2 = 0) = I2/ V2 (where V1 = 0) i.e. Y11 = Y22
Hybrid Parameters (h-Parameters):
h-parameters can be defined by the following equations
)2.....(..............................
)1......(..............................
2221212
2121111
VhIhI
VhIhV
+=
+=
1
21
I2I1
Y11 Y22Y12V2 Y21V1
2
1
1
V2V1
Fig(c) Short circuit admittance parameter representation of a two port net work.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
29/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 29
In matrix form
)3(..............................2
1
2221
1211
2
1
=
V
I
hh
hh
I
V
If port 2-21
is short circuited, i.e. V2 = 0 then
1
221
1
111 &
I
Ih
I
vh ==
h11 is called input impedance and h21 is called forward current gain.
If port 1-11 is open circuited, i.e., I1=0 then
2
222
2
112
&v
Ih
v
vh ==
h22 is called output admittance and h12 is called reverse voltage gain.
ABCD Parameters:
ABCD parameters can be defined by the following equations
)2..(....................).........()1.(....................).........(
221
221
IDCVIIBAVV+=+=
In matrix form
)3.........(....................2
2
1
1
=
I
V
DC
BA
I
V
h22
1I1
h11
+
-h12V2
1
V1
Fig (d) Hybrid parametric representation of a two port net work.
2
I2
h21I1
2
V2
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
30/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITU TE OF ENGIN EERING & TECH NOLOGY 30
If port 2-21
is open circuited i.e., I2=0 then
2
1
2
1 &V
IC
V
VA ==
A is called reverse voltage ratio and C is known as transfer admittance.
If port 2-21
is short circuited i.e., V2=0 then
2
1
2
1 &I
ID
I
VB
=
=
B is called transfer impedance and D is called reverse current ratio.
PROCEDURE:-
1. Connect the circuit as per circuit diagram.2. With the Switches S2 open, S3 close to 11' and S4 open, note down the
corresponding readings of voltmeter and ammeter in S.No 1 in Tabular form afterclosing the Switch S1 to supply mains
3. With the Switches S1 open, S4 close to 33' and S3 open, note down thecorresponding readings of voltmeter and ammeter in S.No 2 in Tabular after
closing the Switch S2 to supply mains4. With the Switches S2 open, S3 close to 11' and S4 close to 44', note down the
corresponding readings of voltmeter and ammeter in S.No 3 in Tabular afterclosing the Switch S1 to supply mains
5. With the Switches S1 open, S3 close to 22' and S4 close to 33 ', note down thecorresponding readings of voltmeter and ammeter in S.No 4 in Tabular after
closing the Switch S2 to supply mains
OBSERVATION TABLE:-
S.NO Test Condition V1 (V) I1 (A) V2 (V) I2 (A)
1
Port 2 Open
(I2 = 0) andPort-1 Active
2
Port 1 Open
(I1=0) andPort-2 Active
3Port 2 Short (4 - 4)
(V2=0) and
port-1 active
4
Port 1 Short (2 - 2)
(V1=0) andPort-2 active
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
31/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 31
PRECAUTIONS:
1. Note down the readings of voltmeter and ammeter without parallax error.
2. The current through a particular element should be maintained below its currentrating.
3. The conditions of switches should be thoroughly checked before making the
circuit live
RESULTS:
Name of the
ParameterTheor Pract Theor Pract Theor Pract Theor Pract
Z-parameter Z11= Z12= Z21= Z22=
Y-parameter Y11= Y12= Y21= Y22
h-parameter h11= h12= h21= h22
ABCD-
parametersA= B= C= D=
CONCLUSIONS:
VIVA QUESTIONS:
1) What is the significance of the two port parameters?2) How you know the admittance parameters from impedance parameters?
3) What are the application of Z& Y parameters?4) What is the condition for reciprocal network?
5) What is the condition for symmetrical network?6) What is a Lattice network?
7) What is a Ladder network?
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
32/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 32
DETERMINATION OFSELF, MUTUAL
INDUCTANCES AND
COEFFICIENT OF
COUPLING
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
33/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 33
Experiment no: Batch no: Date:
DETERMINATION OF SELF, MUTUAL AND
COEFFICIENT OF COUPLINGAIM:
To determine the self inductance of a given transformer windings.To determine the mutual inductance and coefficient of coupling of a given transformer.
APPARATUS:
S.NOCOMPONENTS
REQUIREDRATING TYPE QUANTITY
1. Voltmeter (0-300)V PMMI 2
2. Ammeter (0-5)A PMMI 2
3. Switches ---- DPST 2
4. Fuse 10A Tin coated copper 2
5. Connecting wires 1mm2
---- As per required
THEORY:
The property of the coil which opposes any change in the current passing
through it is called self inductance or only inductance. It is analogous to electrical inertiaor electromagnetic inertia.
MAGNITUDE OF SELF INDUCED EMF: From Faradays law of electromagneticinduction, self induced emf can be expressed as
E= - Nd/dt
Negative sign indicate the direction of emf opposing change in current due to which it
exists.
The flux can be expressed as
= (flux/ampere)*ampere = (/I)*I
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
34/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 34
Now as long as permeability is constant, ratio of flux to current remains constant.
Rate of change of flux= (/I)*rate of change of current
d/dt= (/I)*(dI/dt)
e= (-N/I)*(dI/dt)
e= - (N/I) dI/dt
The constant N/I in this expression is nothing but the quantitative measure of theproperty due to which coil opposes any change in current. So this constant is calledcoefficient of self inductance and denoted by L.
L= N/I where its units are henry (H)
MUTUAL INDUCTANCE: The mutual inductance between the two circuits isdefined as the flux linkage of one circuit to the current in the other circuit. Thus the
inductance M12 is given by
M12=flux linkage in circuit 1/current in circuit 2= (N121)/I2
Similarly mutual inductance M21 is given by M21=flux linkage in circuit 2/current incircuit 1= (N212)/I1
If the medium surrounding two circuits in linear without ferromagnetic material, thenmutual inductance represented in equation are equal, thus for linear medium around, two
circuits we can write
M12=M21=M where units are Henry (H)
COEFFICIENT OF COUPLING: When two magnetic circuits kept closed to eachother interact with each other magnetically through flux linkage in the circuit, due tocurrent in other circuit then the circuits are called magnetically coupled circuits.
M=K*[ (L1*L2)]
Where K is called coefficient of coupling between two coils.
When two magnetic circuits are coupled together in series aiding and if M is the mutualinductance between them, then effective inductance of system is given by
Leq= (L1+L2+2M) H
Similarly two magnetic circuits with inductance L1 and L2 are magnetically coupled inseries opposing then effective inductance is given by
Leq= (L1+L2-2M) H
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
35/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 35
APPLICATIONS:
Transformer being a static with full load efficiency around 98% areextensively used in various applications. The various applications may cause under any
one of the following categories.
(1)Steeping up of voltage: Electrical energy in generating like hydro power stations,situated fart away from consumers, is generating at a voltage around 11kv.Fortransmitting the power from generating stations to the place of use by long transmission
lines, it is more economical to raise the level of voltage of transmission of 230kv or400kvs.This steeping up of voltage is carried by installing transformer.
(2) Steeping down of voltage: High tension consumers are provided with electrc powers
at 11kv or 6.6kv, 3-phase.The consumers at his/her cost has to install transformer to stepdown the voltage to 415v,3-phase to shift their requirement.
(3)Instrument extension: To measure high current in the order of several hundreds ampereand voltage of several kilowatt measurements transformers are used along with ammeter
and voltmeter of lower range.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
36/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 36
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
37/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 37
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
38/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 38
PROCEDURE:
SELF INDUCTANCE:
1. Connect the circuit as per the circuit diagram.
2. Give the supply and connect switch to 1-1 and note down the readings of
V1 and I1 which gives Z1.
3. Connect switch to z-z1
and note down the readings of V2 and I2 which gives Z2.
4. By using the multimeter calculate the resistance of primary and secondary.
5. Using the formula Z=R+jXc, calculate L1 and L2.
MUTUAL INDUCTANCE:
1. Connect the circuit as per circuit diagram.
2. Adjust the variac voltage 230v and note the readings of voltmeter and ammeter and
find mutual inductance.
OBSERVATION TABLE:
SELF INDUCTANCE:
S.NOSWITCH S
POSITION
VOLTMETER
READING(V)
AMMETER
READING(A)RESISTANCE()
MUTUAL INDUCTANCE:
S.NOVOLTMETER
READING(V)
AMMETER
READING(A)RESISTANCE()
PRECAUTIONS:
1. Note down the readings from ammeter and voltmeter without parallax errors.
2. Care should be taken that the ammeter reading should not exceed the rated value.
RESULT:
Hence the mutual inductance of a given transformer is verified.
Hence the self inductance of a given transformer is verified.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
39/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 39
DETERMINATION OFFORM FACTOR OF A
NON-SINUSOIDAL
WAVEFORM
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
40/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITU TE OF ENGIN EERIN G & TECH NOLOGY 40
Experiment no: Batch no: Date:
DETERMINATION OF FORM FACTOR OF NON-
SINUSOIDAL WAVEFORM
AIM:To determine the form factor of a non-sinusoidal waveform.APPARATUS:
S.NO Name of Apparatus RANGE TYPE QUANTITY
1 Voltmeter (0-300)V PMMI 1
2 Ammeter (0-5)A PMMI 1
3 Rheostat 12/5A WW 14 Fuse 5A TCC 2
5 CRO 20MHZ 1
6 Connecting wires 1mm As required
NAME PLATE DETAILS:
S.NO RATING TRANSFORMERAUTO
TRANSFORMER
1 KVA 2 2.7
2 Voltage 115/230V (0-270)V
3 Current 17.4A/8.7A 10A
4 Frequency 50HZ 50HZ
THEORY:
AVERAGE VALUE: In a.c circuit applications we are interested in finding out value of a
waveform, that wave could be sinusoidal, triangular or any other shape.
DEFINITION: The value of a cycle of a waveform in the area under the waveform
divided by length of one cycle.
Mathematically vavg= (1/T) 0TVdt where T is time period
Vavg= (v1+v2+v3++vn)/n
THEORITICAL VALUE: Vavg = RVm/n = 0.6366vm for sine waveform
ROOT MEAN SQUARE VALUE (RMS VALUE): In mathematics, the root mean
square also known as quadratic mean. It is a statistical measure of the magnitude of a
varying quantity especially useful when variants are positive and negative.
Eg: sinusoid
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
41/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITUT E OF ENGINEERIN G & TECH NOLOGY 41
It can be calculated for a series of discrete values or continuously varying function. The
name comes from the fact that it is the square root of the mean of the square of the value.
It is a special case of power mean with the exponent, p=2.
DEFINITION: The rms or effective value of a wave is defined as that dc value whichallowed to flow through a particular resistance for a certain time would produce the same
heating effect as that produced by the wave.
Mathematically ==T
effrms dttVT
II0
2)(1
The rms of collection of n values is given by
nVVVV nrms )(
22
2
2
1 +++=LLL
=0.707vm (sinusoidal wave)
The RMS value of a periodic function is equal to the rms of one period of one function.The RMS value of a continuous function or signal can be approximately calculated by
taking the rms of a series of equally spaced samples. It is used to get average electricpower. It is used to find RMS value of a given waveform.
FORM FACTOR: The form factor of an alternating current waveform (signal) is theratio of rms values to the average value (mathematically) mean of absolute value of all
points on the waveform.
In case of sinusoidal waveform, the form factor is approximately equal to 1.11
Mathematically form factor = Vrms/Vavg
Theoretical value: 1107.122
=
m
m
V
V
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
42/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITUT E OF ENGINEERIN G & TECH NOLOGY 42
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
43/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITUT E OF ENGINEERIN G & TECH NOLOGY 43
PROCEDURE:
1. Connect the circuit as per circuit diagram.
2. Plot the graph that appears on CRO connected to the resistor i.e., non sinusoidal wave
form.
3. Divide the waveform into n-parts.
4. Calculate the Vrms using the formula( )
voltsn
VVVV nrms
22
2
2
1 +++=LLLL
5. Calculate the form factor asavg
rms
V
V
PRECAUTIONS:
1.Note down the readings from ammeter and voltmeter without parallax errors.
2.Care should be taken that the ammeter reading should not exceed the rated value.
3.Trace the waveform carefully from CRO.
RESULT:
The theoretical and practical values for form factor are
Theoretical value Practical value
CONCLUSION: Theoretical and practical values of a form factor are found to beapproximately equal.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
44/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUT E OF ENGINEERIN G & TECH NOLOGY 44
VERIFICATION OF
COMPENSATION
THEOREM
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
45/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITUT E OF ENGINEERIN G & TECH NOLOGY 45
Experiment no: Batch no: Date:
VERIFICATION OFCOMPENSATION THEOREM
AIM:-To verify compensation theorem.
APPARATUS:-
S.No APPARATUS RANGE TYPE QUANTITY
1 Voltmeter 0-300V MI 1
2 Ammeter 0-1A MI 1
3 Rheostats290/2.8A WW 155/1.7A WW 1
4 1- Variac 230/0-270V,8A ----- 1
THEORY:-
In a linear, network N, if the current in the branch is I and the impedance Zof the branch is increased by Z, then the increment of voltage and current in each branchof network is that voltage and currents that would be produced by an opposing voltage
source of value VC = IZ introduced into the altered branch after the modification.
EXPLANATION:-Consider network N in figure (A), having branch impedance Z. Let the
current through Z be I and its voltage be V.
Let Z be the change in Z. Then I (the new current) can be written as,
I= VOC / (Z+ Z+Zs)
I = I I = V0C/ (Z+ Z+Zs) - VOC / (Z+ Zs)= - (VOC / (Z+ Zs)) (Z/ (Z+ Z+Zs))
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
46/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUT E OF ENGINEERIN G & TECH NOLOGY 46
= -IZ/ (Z+ Z+Zs)
= - Vc/ (Z+ Z+Zs)
Where, Vc = IZThe equation shown above follows the shown below in which I has the
same direction as I.
This shows that the change in current I due to change in any branch in a linearnetwork can be can be calculated by determining the current in that branch in a network
obtained from the original network, by nulling all the independent sources and placing avoltage source called the compensation source in series with the branch whose value is Vc= IZ, where I is the current through the branch before its impedance is changed and Zis the change in the impedance. The direction of Vc is opposite to that of I.
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
47/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITUT E OF ENGINEERIN G & TECH NOLOGY 47
CIRCUIT DIAGRAM -1:-
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
48/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUT E OF ENGINEERIN G & TECH NOLOGY 48
CIRCUIT DIAGRAM -2:-
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
49/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITUT E OF ENGINEERIN G & TECH NOLOGY 49
CIRCUIT DIAGRAM -3:-
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
50/58
DEPARTM ENT OF EEE EC&S LAB
LENDI INSTITU TE OF ENGIN EERING & TECH NOLOGY 50
TABULAR FORM 1:-
S.NO. Voltage (V) Current I (Amps)
TABULAR FORM -2:-
S.No. Voltage (V) Current I(Amps)
TABULAR FORM-3:-
S.No. Voltage (V) Current I (Amps)
PROCEDURE:-
1. Connections are made as per the circuit diagram.2. With the help of 1 - Variac apply 200V to the circuit.3. Note down the corresponding ammeter readings (I).4. Apply 200V to the circuit 2 and note the corresponding ammeter readings(I
).
5. Apply compensating Voltage (VC) to the circuit 3 and note down thecorresponding ammeter readings (I).
PRECAUTIONS:-
1. Before switching on the supply for each circuit it should be ensured that allrheostats at maximum position and during the experiment this should not be
disturbed.2. It is also to be ensured that the auto transformer should be at minimum position
before switching on the power supply.
RESULT:-
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
51/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 51
MEASUREMENT OF 3-PHASE
POWER BY 2-WATTMETER
METHOD
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
52/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 52
Experiment no: Batch no: Date:
Measurement of 3-phase Power by two Wattmeter MethodAIM: To measure 3-phase power by two wattmeter method for the given load.
APPARATUS :
THEORY:-
In a three phase three wire system we require 3 elements, but if we make thecommon points of the pressure coils coincide with one of the lines, then we will require
only n-1=2 elements.
Let us consider two wattmeters connected to measure power in three phase circuitas shown in figure. The sum of the two wattmeter readings is equal to the power
consumed by the load. This is irrespective of the load is balanced or unbalanced.
Total Active power is given by P = W1+W2
Total Reactive power is given by Q = 3 (W1-W2)
Power factor is given by
Where W1 & W2 are two wattmeter readings, they can be expressed mathematically as
W1 = VL IL cos (30-)
W2 = VL IL cos (30+)
When power factor is unity both the wattmeter show same reading. As the power
factor decreases, up to 0.5 both the meters read positive values but unequal. If the powerfactor decreases below 0.5 one of the wattmeter shows negative reading. In such case we
have to inter change either current coil or pressure coil connections.
S. No Name of Apparatus Type Range Quantity
1 Voltmeter PMMC 0-600V 1
2 Ammeter PMMC 0-10A 1
3 Rheostat WW 50/5A 3
4 Wattmeter -- 600V, 10A, UPF 2
5 Fuse TCC 10A --
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
53/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 53
0-600V
MI
50 / 5A
50/ 5A
50
/5A
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
54/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 54
0-600V
MI
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
55/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 55
0-600V
MI
RBY
CBY
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
56/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 56
0-600V
MI
RBY
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
57/58
DEPARTM ENT OF EEE EC&S LAB
LENDI IN STITU TE OF ENGIN EERING & TECH NOLOGY 57
PROCEDURE:-
1. Connect the circuit as per circuit diagram.
2. Initially variac should be in minimum position.
3. Close the TPST switch and slowly vary the variac until voltmeter reads line voltage of
415 V.
4. Note down the readings of Wattmeter, Voltmeter and Ammeter and tabulate.
OBSERVATION TABLE:-
S.NO. VL (V) IL (A) W 1(watt) W2 WT=W1+W2
PRECAUTIONS:
1. Avoid Loose Connections.
2. Readings must be taken without parallax error.3. Before switching on the supply for the circuit, ensure that all rheostats are at maximum
position and during the experiment these should not be disturbed.
RESULTS:
CONCLUSIONS:
w.jntuworld.com
www.jntuworld.com
www.jw
7/30/2019 Electrical Circuits Simulation
58/58
DEPARTM ENT OF EEE EC&S LAB
VIVA QUESTIONS:
1. What is active power?2. What are the different powers available?
3. What is the difference between balanced load & un balanced load?
4. Draw the Phasor diagram.5. What is the active power consumed for a purely inductive and capacitive loads.6. What is the apparent power for a resistive load.
w.jntuworld.com www.jw
top related