Electonic Wireless and Wired Voting Machine
Post on 08-Aug-2018
225 Views
Preview:
Transcript
8/22/2019 Electonic Wireless and Wired Voting Machine
1/65
1 | P a g e
I hereby certify that the work which is being presented in the B.Tech. Major Project Report
entitled Design ofElectronic Voting Machine (Wired & Wireless), in partial fulfillment of
the requirements for the award of the Bachelor of Technology in Electronics & Communication
Engineering and submitted to the Department of Electronics & Communication Engineering of
Arni University is an authentic record of our own work carried out during a period from March
2013 to June 2013 (8th
semester) under the supervision of Mr.,ECE Department.
The matter presented in this Project Report has not been submitted by us for the
award of any other degree elsewhere.
Signature of Student (S)KHEM RAJ
BHARAT BHUSHAN SANKHYAN
GAURAV SHARMA
ABHISHEK SAMBYAL
VIVEK SHARMA .
This is to certify that the above statement made by the student(s) is correct to the best ofmy knowledge.
Signature of Supervisor(s)MR. Sharad Prasad .
HOD,
8/22/2019 Electonic Wireless and Wired Voting Machine
2/65
2 | P a g e
ACKNOWLEDGEMENT
I take this opportunity to express my profound gratitude and deep
regards to our guide Mr. Sarad Parsad for his exemplary guidance,
monitoring and constant encouragement throughout the course of
this project. The blessing, help and guidance given by him time to
time shall carry us a long way in the journey of life on which we areabout to embark.
I also take this opportunity to express a deep sense of gratitude to
our University management team to provide us such a platform
where we can give directions to our ideas.The success of this project
is one of the the result of this platform..
We have immense pleasure in expressing our thanks and deep sense
of gratitude to my rpp
I am obliged to staff members of Electronics and communication, forthe valuable information provided by them in their respective fields.
I am grateful for their cooperation during the period of myassignment.
Lastly, we thank almighty, our parents and friends for their
constant encouragement without which this assignment would not
be possible.
BHARAT BHUSHAN SANKHYAN
ABHISHEK SAMBYAL
GAURAV SHARMA
VIVEK SHARMA
KHEM RAJ
8/22/2019 Electonic Wireless and Wired Voting Machine
3/65
3 | P a g e
ABSTRACT
According to Election Data Services the percentage of electronic voting machines per
county doubled between 1998 and 2002 to 16 percent-, yet a full replacement of the traditional
voting procedure is very unlikely. In its essence, an electronic voting machine is a computer
assisted self-interviewing device (CASI) giving the voter the opportunity to review and change
his/her vote before submitting it. The different types of voting machines allow for different kinds
of interaction, such as using a touch screen technology, using a dial wheel, touching a paper
panel, or pressing a button on an LCD screen. Each machine provides feedback for blank ballots
and under-voting and prevents selecting more choices than the maximum allowed. Some
machines even have advanced functions such as increasing the font for visually impaired votersand/or allowing for listening of the voting options rather than reading. The common features
electronic voting machines share with CASI and ACASI devices allow for theoretical and
empirical predictions of the advantages and disadvantages this technology can provide. The
paper presents an overview of the different types of voting machines and based on established
theories and results from CASI and ACASI studies, examines and compares characteristics of the
machines currently used and computer-human interaction mechanisms, their potential effects,
and unexplored applications. Furthermore, possibilities such as prediction of candidates name
order effect, already existing in the literature, and computer literacy effect on voting are
discussed.
8/22/2019 Electonic Wireless and Wired Voting Machine
4/65
4 | P a g e
Table of Contents Certificate
1 Acknowledgement
..2 Abstract
...3
Contents...4
1.INTRODUCTION..61.1 The Electronic Voting Machine An Electronic Marvel.6
1.2History6
1.3Description8
1.4 Pictorial description of working of electronic votingmachine..9
1.5Challenges for Electronic Voting inIndia..9
2. TOOLSUSED ..11
8/22/2019 Electonic Wireless and Wired Voting Machine
5/65
5 | P a g e
2.1 HardwareTools11
2.2 SoftwareTools..12
3. FLOW DIAGRAM..144. BLOCKDIAGRAM .154.1.Description Of BlockDiagram.....16
5.COMPONENTSUSED..19 5.1 BriefDescription ofComponents20
6.OPERATION 6.1 Operation or Working ofProject..
7.SOFTWARECODE.. 7.1code
7.2 Proteusfile...
8.HARDWAREDESIGN. 9.ADVANTAGES ANDAPPLICATIONS10. CONCLUSION &FUTURE SCOPE OF WORK..
8/22/2019 Electonic Wireless and Wired Voting Machine
6/65
6 | P a g e
11.REFERENCE.
8/22/2019 Electonic Wireless and Wired Voting Machine
7/65
7 | P a g e
INTRODUCTION1.1The Electronic Voting MachineAn Electronic Marvel
Electronic Voting Machine (EVM) retains all the characteristics of voting by ballot papers,
while
making polling a lot more expedient. Being fast and absolutely reliable, the EVM saves
considerable time, money and manpower. And, of course, helps maintain total voting
secrecy
without the use of ballot papers. The EVM is 100 per cent tamper proof. And, at the end of
the
polling, just press a button and there you have the results.
1.2 History
The EVMs were devised and designed by Election Commission of India in collaboration
with two Public Sector undertakings viz., Bharat Electronics
Limited, Bangalore and Electronics Corporation of India Limited, Hyderabad. The EVMs
are now manufactured by the above two undertakings.
EVMs were first used in 1982 in the by-election to North ParavurAssembly ConstituencyofKerala for a limited number of polling stations (50 polling stations).
1.2.1 Electronic Voting in India
The Election Commission of India developed the countrys EVMs in partnership with two
government-owned companies, the Electronics Corporation of India (ECIL) and Bharat
Electronics Limited (BEL) Though these companies are owned by the Indian government,
they are not under the administrative control of the Election Commission. They are profit-
seeking vendors that are attempting to market EVMs globally.
The first Indian EVMs were developed in the early 1980s by ECIL. They were used in
certain parts of the country, but were never adopted nationwide .They introduced the style
of system used to this day (see Figure 1.1), including the separate control and ballot units
and the layout of both components.
These first-generation EVMs were based on Hitachi 6305 microcontrollers and used
firmware stored in external UV-erasable PROMs along with 64kb EEPROMs for storing
votes. Second-generation models were introduced in 2000 by both ECIL and BEL. These
machines moved the firmware into the CPU and upgraded other components. They were
gradually deployed in greater numbers and used nationwide beginning in 2004. In 2006, the
http://en.wikipedia.org/wiki/Election_Commission_of_Indiahttp://en.wikipedia.org/wiki/Bharat_Electronicshttp://en.wikipedia.org/wiki/Bharat_Electronicshttp://en.wikipedia.org/wiki/Bangalorehttp://en.wikipedia.org/wiki/Electronics_Corporation_of_India_Limitedhttp://en.wikipedia.org/wiki/Hyderabad,_Indiahttp://en.wikipedia.org/wiki/North_Paravurhttp://en.wikipedia.org/wiki/Keralahttp://en.wikipedia.org/wiki/Keralahttp://en.wikipedia.org/wiki/North_Paravurhttp://en.wikipedia.org/wiki/Hyderabad,_Indiahttp://en.wikipedia.org/wiki/Electronics_Corporation_of_India_Limitedhttp://en.wikipedia.org/wiki/Bangalorehttp://en.wikipedia.org/wiki/Bharat_Electronicshttp://en.wikipedia.org/wiki/Bharat_Electronicshttp://en.wikipedia.org/wiki/Election_Commission_of_India8/22/2019 Electonic Wireless and Wired Voting Machine
8/65
8 | P a g e
manufacturers adopted a third-generation design incorporating additional changes
suggested by the Election Commission.
.
According to Election Commission statistics, there were 1,378,352 EVMs in use in July
2009. Of these, 448,000 were third-generation machines manufactured from 2006 to 2009,
with 253,400 from BEL and 194,600 from ECIL. The remaining 930,352 were the second-
generation models manufactured from 2000 to 2005, with 440,146 from BEL and 490,206
from ECIL [26]. (The first generation machines are deemed too risky to use in national
elections because their 15-year service life has expired [1], though they are apparently still
used in certain state and local contests.) In the 2009 parliamentary election, there were
417,156,494 votes cast, for an average of 302 votes per machine .The EVM we tested is
from the largest group, a second-generation ECIL model. It is a real machine that was
manufactured in 2003, and it has been used in national elections. It was provided by a
source who has requested to remain anonymous. Photographs of the machine and its inner
workings appear throughout this paper. Other types and generations of machines have
certain differences, but their overall operation is very similar. We believe that most of our
security analysis is applicable to all EVMs now used in India.
8/22/2019 Electonic Wireless and Wired Voting Machine
9/65
9 | P a g e
1.3Description:
Electronic voting machine has now days become an effective tool for voting. It ensures
flawless
voting and thus has become more widespread. It ensures people about their vote being
secured. It
avoids any kind of malpractice and invalid votes. Also such kind of system becomes more
economical as consequent expenditure incurred on man power is saved. It is also
convenient on
the part of voter, as he has to just press one key whichever belongs to his candidates.
voting machines are the total combination of mechanical, electromechanical,
or electronic equipment (including software, firmware, and documentation required to
program
control, and support equipment), that is used to define ballots; to cast and count votes; to
report
or display election results; and to maintain and produce any audit trail information. The
first
voting machines were mechanical but it is increasingly more common to use electronic
voting machines.A voting system includes the practices and associated documentation used to identify
system
components and versions of such components; to test the system during its development
and
maintenance; to maintain records of system errors or defects; to determine specific changes
made
after initial certification; and to make available any materials to the voter (such as notices,
8/22/2019 Electonic Wireless and Wired Voting Machine
10/65
10 | P a g e
instructions, forms, or paper ballots).
Traditionally, a voting machine has been defined by the mechanism the system uses to cast
votes
and further categorized by the location where the system tabulates the votes.
Voting machines have different levels of usability, security, efficiency and accuracy.
Certainsystems may be more or less accessible to all voters, or not accessible to those voters with
certain
types of disabilities. They can also have an effect on the public's ability to oversee
elections.
1.4 Pictorial description of working of electronic voting machine
8/22/2019 Electonic Wireless and Wired Voting Machine
11/65
11 | P a g e
The control unit/MCU and the ballot unit are discussed in detail in chapter 2 under section
2.1.
1.5Challenges for Electronic Voting in India
Indian voting machines must be designed to function under more challenging
environmental conditions and operational constraints than other electronic voting systems
studied in previous security reviews. These requirements have influenced the simple design
of the current machines and impact our security analysis. Among the challenges are:
Cost: With well over a million EVMs in use, the cost of the system is a major concern.
The current EVMs are built from inexpensive commodity parts and cost approximately
$200 for each set of units,far less than many DREs used in the U.S., which cost several
thousand dollars.
Power: Many polling places are located in areas that lack electricity service or have onlyintermittent service .Thus, the EVMs operate entirely from battery power, rather than
merely using a battery as a backup.
Natural Hazards: Indias varied climate has great extremes of temperature, as well as
other environmental hazards such as dust and pollution. EVMs must be operated under
these adverse conditions and must be stored for long periods in facilities that lack climate
control. An Election Commission report cites further dangers from attack by vermin, rats,
fungus or due to mechanical danger, [that might cause] malfunction .
Illiteracy :Though many Indian voters are well educated, many others are illiterate. The
countrys literacy rate in 2007 was 66% , and only about 55% among women, so handling
illiterate voters must be the rule rather than the exception. Thus, ballots feature graphical
party symbols as well as candidate names, and the machines are designed to be used
without written instructions.
Unfamiliarity with Technology: Some voters in India have very little experience with
technology and maybe intimidated by electronic voting. For example, Fifty-year-old
Hasulal Topno impoverished Oraon tribal, who gathers firewood from the forest outlying
the Palamau Tiger Reserve, a Maoist hotbed 35 km from Daltonganj town told a reporter,
I am scared of the voting machine, prior to its introduction in his village . Nirmal Ho, a
tribal and a marginal farmhand in the Chatarpur block ofPalamau district, said he wasmore scared of the EVMs than the Maoists on account of his unfamiliarity with
technology. To avoid further intimidating voters like these, Indias EVMs require the voter
to press only a single button.
Booth Capture: A serious threat against paper voting before the introduction of EVMs
was booth capture, a less-than-subtle type of electoral fraud found primarily in India,
wherein party loyalists would take over a polling station by force and stuff the ballot box.
8/22/2019 Electonic Wireless and Wired Voting Machine
12/65
12 | P a g e
Better policing makes such attacks less of a threat today, but the EVMs have also been
designed to discourage them by limiting the rate of vote casting to five per
minute .Any voting system proposed for use in India must be able to function under these
constraints.
***************
TOOLS USED
2.1 HARDWARE TOOLS:
2.1.1 The control Unit : In Total control of the pollingConduction of polling, display of total votes polled, sealing at the end of the poll, and
finally,
declaration of resultsthese are the various accomplishments ofjust one gadget : the
control
unit. In total control of the polling, this electronic unit gives you all necessary information
at a
press of a few buttons. For instance, if you need to know the total number of votes, you just
have
to press the Total switch. Candidates-wise results can be had only at the end of polling.
2.1.2 The Ballot Unit : An electronic ballot box.
A simple voting device, it displays the list of candidates. A facility to incorporate party
names
and symbols is in-built. All the voter has to do ispress the desired switch located next to thename of each candidate. The main advantage is the speed, apart from the simplicity of
operation,
which requires no training at all. A single ballotunit takes in the names of 16 candidates.
And
thus, by connecting four ballot units the EVM can accommodate a total of 64 candidates in
a
single election.
8/22/2019 Electonic Wireless and Wired Voting Machine
13/65
13 | P a g e
2.2 SOFTWARE TOOLS:
2.2.1 KEIL SOFTWARE:
The Keil 8051 Development Tools are designed tosolve the complex problems facing
embedded
software developers. When starting a new project, simply selectthe microcontroller you use from the Device
Database and the Vision IDE sets all compiler,assembler, linker, and memory options for
you.
Numerous example programs are included to help you get started with the most popular
embedded 8051 devices.
The Keil Vision Debugger accurately simulates on-chip peripherals (IC, CAN, UART,
SPI, Interrupts, I/O Ports, A/D Converter, D/A Converter, and PWM Modules) of your
8051
device. Simulation helps you understand hardware configurations and avoids time wasted
onsetup problems. Additionally, with simulation, you can write and test applications before
target hardware is available.
8/22/2019 Electonic Wireless and Wired Voting Machine
14/65
14 | P a g e
2.2.2 PROTEUS SOFTWARE:
Proteus 7.0 is a Virtual System Modelling (VSM) that combines circuit simulation,
animated components and microprocessor models to co-simulate the complete
microcontroller based designs. This is the perfect tool for engineers to test theirmicrocontrollerdesigns before constructing a physical prototype in real time. This program
allows users to interact withthe design using on-screen indicators and/or LED and LCD
displays and, ifattached to the PC, switches and buttons.
One of the main components of Proteus 7.0 is the Circuit Simulation -- a product that uses
a SPICE3f5analogue simulatorkernel combined with an event-driven digital simulator that
allow users to utilize any SPICE model by any manufacturer.
Proteus VSM comes with extensive debugging features, including breakpoints, single
stepping and variable display for a neat design prior to hardware prototyping.
In summary, Proteus 7.0 is the program to use when you want to simulate the interaction
between software running on a microcontroller and any analog or digital electronic device
connected to it.
2.2.3 Advantages:
Real time simulation.
Time and money saving.
8/22/2019 Electonic Wireless and Wired Voting Machine
15/65
15 | P a g e
***************
FLOW DIAGRAM
8/22/2019 Electonic Wireless and Wired Voting Machine
16/65
16 | P a g e
***************
BLOCK DIAGRAM OF ELECTRONIC VOTING MACHINE
8/22/2019 Electonic Wireless and Wired Voting Machine
17/65
17 | P a g e
4.1 Description in detail:
The Electronic Voting Machine basically consists of three main blocks;
these are
Micro controller LCD Display
LED
Controlswitches & Keypad Buzzer
8/22/2019 Electonic Wireless and Wired Voting Machine
18/65
18 | P a g e
1)Micro controller:Micro controller senses the signal given from switches and d the mode of operation voting
mode it increments the data for corresponding key i.e. respective candidate as well as it
sends signal to display block to indicate one key is pressed. In counting mode micro
controllers fetches data from memory location and send it to display devices.
2) LCD:Liquid Crystal Display which is commonly known as LCD is an Alphanumeric Display it
means that it can display Alphabets, Numbers as well as special symbols thus LCD is a
user friendly Display device which can be used for displaying various messages unlike
seven segment display which can display only numbers and some of the alphabets. The
only disadvantage of LCD over seven segment is that seven segment is robust display and
be visualized from a longer distance as compared to LCD. Here I have used 16 x 2
Alphanumeric Display which means on this display I can display two lines with maximum
of 16 characters in one line.
3)LED:A light-emitting diode (LED) is a semiconductor light source. LEDs are used as indicator
lamps in many devices and are increasingly used for other lighting.Light-emitting diodes
8/22/2019 Electonic Wireless and Wired Voting Machine
19/65
19 | P a g e
are used in applications as diverse as replacements for aviation lighting, automotive
lighting (particularly
brake lamps, turn signals and indicators) as well as in traffic signals.
4)Control switches:There are three control switches:
I. Clear Votes.
II. Controller switch.
III. Total Votes
5)Buzzer:
8/22/2019 Electonic Wireless and Wired Voting Machine
20/65
20 | P a g e
An electric signaling device, such as a doorbell, that makes a buzzing sound. Also we can
say it is an audio signaling device, which may be mechanical, electromechanical,
orpiezoelectric. Typical uses of buzzers and beepers include alarm devices, timers and
confirmation of user input such as a mouse click or keystroke.
***************
http://en.wikipedia.org/wiki/Soundhttp://en.wikipedia.org/wiki/Machinehttp://en.wikipedia.org/wiki/Electromechanicshttp://en.wikipedia.org/wiki/Piezoelectricityhttp://en.wikipedia.org/wiki/Alarm_deviceshttp://en.wikipedia.org/wiki/Timerhttp://en.wikipedia.org/wiki/Timerhttp://en.wikipedia.org/wiki/Alarm_deviceshttp://en.wikipedia.org/wiki/Piezoelectricityhttp://en.wikipedia.org/wiki/Electromechanicshttp://en.wikipedia.org/wiki/Machinehttp://en.wikipedia.org/wiki/Sound8/22/2019 Electonic Wireless and Wired Voting Machine
21/65
21 | P a g e
LIST OF COMPONENT USED FOR DESIGNING ELECTRONIC
VOTING MACHINE
Component name Quantitiy
1. Microcontroller(AT 89v59) 1
2. Transistor
a. 7805 23. Lcd 16x2 1
4. Switches (push to on) 11
5. Resistances
a. 10k 7b. 330 1c. 270k 1d. 220k 2e. 55k 1f. 33k 1
6. Capacitor
a. 33pf 2b. 10f 1
7. Buzzer 2
8. LED 5
1) Multicolor 22) Green 3
9. Crystal 12 Mhz 1
10.Encoder HT-12E 1
11.Decoder HT-12D 1
12.Burg connector 8
13.Reciver Trasmitter pair( A -434) 1
14.Diode 4007 8
8/22/2019 Electonic Wireless and Wired Voting Machine
22/65
22 | P a g e
15.Antenna (wire FM) 1 pair
16.Battery 9v 2
BRIEF DESCRIPTION OF COMPONENTS USED
1) Microcontroller 89v511.1 FEATURES
compatible with mcs-51products
4k bytes of in-system reprogrammable flash memoryendurance: 1,000 write/erasecycles
fully static operation: 0 hz to 24 mhz
three-level program memory lock
128 x 8-bit internal ram
32 programmable i/o lines
two 16-bit timer/counters
six interrupt sources
programmable serial channel
low-power idle and power-down modes
1.2 DESCRIPTION
The at89v51 is a low-power, high-performance cmos 8-bit microcomputer with 4k Bytes offlash programmable and erasable read only memory . The device Is manufactured usingatmels high-density nonvolatile memory technology and is Compatible with the industrystandard mcs-51 instruction set and pin out. The on-chip Flash allows the program memoryto be reprogrammed in-system or by a conventional nonvolatile memory programmer. Bycombining a versatile 8-bit cpu with flash On a monolithic chip, the atmel at89v51 is apowerful microcomputer which provides A highly-flexible and cost-effective solution tomany embedded control applications.
8/22/2019 Electonic Wireless and Wired Voting Machine
23/65
23 | P a g e
8/22/2019 Electonic Wireless and Wired Voting Machine
24/65
24 | P a g e
1.3 PIN DESCRIPTION
1) VccSupply voltage.
2) GndGround.
3) Port 0
8/22/2019 Electonic Wireless and Wired Voting Machine
25/65
25 | P a g e
Port 0 is an 8-bit open-drain bi-directional i/o port. As an Output port, each pin can sinkeight ttl inputs. When 1s Are written to port 0 pins, the pins can be used as high-impedanceinputs. Port 0 may also be configured to be the multiplexed low-order address/data busduring accesses to external pro-gram and data memory. In this mode p0 has internal Pullups.
Port 0 also receives the code bytes during flash programming , and outputs the code bytesdu ring program Verification. External pull ups are required during program Verification.
4) Port 1Port 1 is an 8-bit bi-directional I/O port with internal pull ups. The Port 1 output bufferscan sink/source four TTL inputs. When 1s are written to Port 1 pins they are pulled high by
the internal pull ups and can be used as inputs. As inputs, Port 1 pins that are externallybeing pulled low will source current (IIL) because of the internal pull ups. Port 1 alsoreceives the low-order address bytes during Flash programming and verification.
5) Port 2Port 2 is an 8-bit bi-directional I/O port with internal pull ups. The Port 2 output bufferscan sink/source four TTL inputs. When 1s are written to Port 2 pins they are pulled high bythe internal pull ups and can be used as inputs. As inputs, Port 2 pins that are externallybeing pulled low will source current (IIL) because of the internal pull ups. Port 2 emits thehigh-order address byte during fetches from external program memory and during accessesto external data memory that use 16-bit addresses (MOVX @DPTR). In this application, ituses strong internal pull ups when emitting 1s. During accesses to external data memorythat use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 SpecialFunction Register .Port 2 also receives the high-order address bits and some control signalsduring Flash programming and verification.
6) Port 3Port 3 is an 8-bit bi-directional I/O port with internal pull ups .The Port 3 output bufferscan sink/source four TTL inputs .When 1s are written to Port 3 pins they are pulled high bythe internal pull ups and can be used as inputs. As inputs, Port 3 pins that are externallybeing pulled low will source current (IIL) because of the pull ups. Port 3 also serves thefunctions of various special features of the AT89C51 as listed below:
8/22/2019 Electonic Wireless and Wired Voting Machine
26/65
26 | P a g e
Port 3 also receives some control signals for Flash pro-gramming and verification.
7) RSTReset input. A high on this pin for two machine cycles while the oscillator is running resetsthe device.
8) ALE/PROG
Address Latch Enable output pulse for latching the low byte of the address during accessesto external memory. This pin is also the program pulse input (PROG) during Flashprogramming.In normal operation ALE is emitted at a constant rate of 1/6 the oscillator frequency, and
may be used for external timing or clocking purposes. Note, however, that one ALE pulseis skipped during each access to external Data Memory .If desired, ALE operation can bedisabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during aMOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has noeffect if the microcontroller is in external execution mode.
9) PSENProgram Store Enable is the read strobe to external pro-gram memory. When the AT89C51is executing code from external pro-gram memory, PSEN is activated twice each machinecycle, except that two PSEN activations are skipped during each access to external data
memory.10) EA/VPP
External Access Enable. EA must be strapped to GND in order to enable the device to fetchcode from external pro-gram memory locations starting at 0000H up to FFFFH .Note,however, that if lock bit 1 is programmed, EA will be internally latched on reset. EAshould be strapped to VCC for internal program executions .This pin also receives the 12-volt programming enable volt-age (VPP) during Flash programming, for parts that require12-volt VPP.
8/22/2019 Electonic Wireless and Wired Voting Machine
27/65
27 | P a g e
11.a) XTAL1Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
11.b) XTAL2Output from the inverting oscillator amplifier.
Absolute Maximum Ratings*
*notice:
Stresses beyond those listed under absolute Maximum ratings may cause permanentdam-age to the device. This is a stress rating only and Functional operation of the device atthese or anyOther conditions beyond those indicated in the Operational sections of this specification isnotImplied. Exposure to absolute maximum rating Conditions for extended periods may affectdevice Reliability.
1.4 DC Characteristics
8/22/2019 Electonic Wireless and Wired Voting Machine
28/65
28 | P a g e
Notes:1. Under steady state (non-transient) conditions, iol must be externally limited as follows:Maximum Iol per port pin: 10 mAMaximum Iol per 8-bit port: port 0: 26 mAPorts 1, 2, 3: 15 mAMaximum total Iol for all output pins: 71 mAIf iOl exceeds the test condition, vol may exceed the related specification. Pins are notguaranteed to sink current greater Than the listed test conditions.2. Minimum vcc for power-down is 2v.
1.5 AC CHARACTERISTICS
Under operating conditions, load capacitance for port 0, ale/prog, and psen= 100 pf; loadcapacitance for all other Outputs = 80 pf.
8/22/2019 Electonic Wireless and Wired Voting Machine
29/65
29 | P a g e
8/22/2019 Electonic Wireless and Wired Voting Machine
30/65
30 | P a g e
2) LM7805
2.1 PACKAGING INFORMATION
40-lead,0.600wide,plastic dual inline package.
3-Terminal 1A Positive Voltage Regulator
2.2 Features
Output Current up to 1A Output Voltages of 5v Thermal Overload Protection
8/22/2019 Electonic Wireless and Wired Voting Machine
31/65
31 | P a g e
Short Circuit Protection Output Transistor Safe Operating Area Protection.
2.3 General Description
The LM7805 series of three terminal positive regulators are available in the TO-220package and with several fixed output voltages, making them useful in a wide range of
applications. Each type employs internal current limiting, thermal shut down and safe
operating area protection, making it essentially indestructible. If adequate heat sinking is
provided, they can deliver over 1A output current. Although designed primarily as fixed
voltage regulators, these devices can be used with external components to obtain adjustable
voltages and currents.
2.4 Block Diagram
2.5 Pin Assignment
8/22/2019 Electonic Wireless and Wired Voting Machine
32/65
32 | P a g e
2.6 Absolute Maximum Ratings
Absolute maximum ratings are those values beyond which damage to the device may
occur. The datasheet specifications should be met, without exception, to ensure that the
system design is reliable over its power supply , temperature, and output/input loadingvariables. Fairchild does not recommend operation outside datasheet specifications.
2.7 Electrical Characteristics(LM7805)
8/22/2019 Electonic Wireless and Wired Voting Machine
33/65
33 | P a g e
Notes:
1. Load and line regulation are specified at constant junction temperature. Changes in VOdue to heating effects must
be taken into account separately. Pulse testing with low duty is used.2. These parameters, although guaranteed, are not 100% tested in production.
3) HT12E3.1Features
Operating voltage 2.4V~12V
Low power and high noise immunity
CMOS technology
Low standby current: 0.1A
VDD=5V
Minimum transmission word : Four words for the HT12E
Built-in oscillator needs only 5% resistor
Data code has positive polarity
Minimal external components
HT12E: 18-pin DIP/20-pin SOP package
3.2 Applications
Burglar alarm system
Smoke and fire alarm system
Garage door controllers
Car door controllers
Car alarm system
Security system
Cordless telephones
Other remote control systems
3.3 General Description
HT12E is an encoder integrated circuit of 212 series of encoders. They are paired with212 series of decoders for use in remote control system applications. It is mainly used ininterfacing RF and infrared circuits. The chosen pair of encoder/decoder should have samenumber of addresses and data format.
8/22/2019 Electonic Wireless and Wired Voting Machine
34/65
34 | P a g e
Simply put, HT12E converts the parallel inputs into serial output. It encodes the 12 bitparallel data into serial for transmission through an RF transmitter. These 12 bits aredivided into 8 address bits and 4 data bits.HT12E has a transmission enable pin which is active low. When a trigger signal isreceived on TE pin, the programmed addresses/data are transmitted together with the
header bits via an RF or an infrared transmission medium. HT12E begins a 4-wordtransmission cycle upon receipt of a transmission enable. This cycle is repeated as long asTE is kept low. As soon as TE returns to high, the encoder output completes its final cycleand then stops.
3.4 Block Diagram
3.5 Pin Assignment
8/22/2019 Electonic Wireless and Wired Voting Machine
35/65
35 | P a g e
3.6 Pin Description
8/22/2019 Electonic Wireless and Wired Voting Machine
36/65
36 | P a g e
Note: D8~D11 are all data input and transmission enable pins of the HT12A.
TEis a transmission enable pin of the HT12E.
8/22/2019 Electonic Wireless and Wired Voting Machine
37/65
37 | P a g e
3.7 Approximate internal connections
3.8 Absolute Maximum Ratings
Supply Voltage (HT12A) ..............0.3V to 5.5VSupply Voltage (HT12E) ...............0.3V to 13VInput Voltage....................VSS0.3 to VDD+0.3VStorage Temperature.................50Cto125COperating Temperature...............20Cto75C
Note: These are stress ratings only. Stresses exceeding the range specified under AbsoluteMaximum Ratings may cause substantial damage to the device. Functional operation of thisdevice at other conditions beyond those listed in the specification is not implied andprolonged expo-sure to extreme conditions may affect device reliability.
3.9 Electrical Characteristics:
8/22/2019 Electonic Wireless and Wired Voting Machine
38/65
38 | P a g e
3.10 Functional Description
OperationThe 2^12 series of encoders begin a 4-word transmission cycle upon receipt of atransmission enable (TE for the HT12E, active low). This cycle will repeat itself as long asthe transmission enable (TE) is held low. Once the transmission enable returns high theencoder output completes its final cycle and then stops as shown below.
3.11 Flowchart HT12E:
8/22/2019 Electonic Wireless and Wired Voting Machine
39/65
39 | P a g e
8/22/2019 Electonic Wireless and Wired Voting Machine
40/65
40 | P a g e
3.12 Oscillator frequency vs supply voltage
The recommended oscillator frequency is fOSCD(decoder)=50 x fOSCE(HT12E encoder).
4) HT12D (2 12 Series of Decoders)
4.1 General Description
HT12D is a decoder integrated circuit that belongs to 212 series of decoders. This series of
decoders are mainly used for remote control system applications, like burglar alarm, cardoor controller, security system etc. It is mainly provided to interface RF and infraredcircuits. They are paired with 212 series of encoders. The chosen pair of encoder/decodershould have same number of addresses and data format.
In simple terms, HT12D converts the serial input into parallel outputs. It decodes the serial
addresses and data received by an RF receiver, into parallel data and sends them to output
8/22/2019 Electonic Wireless and Wired Voting Machine
41/65
41 | P a g e
data pins. The serial input data is compared with the local addresses three times
continuously. The input data code is decoded when no error or unmatched codes are found.
A valid transmission is indicated by a high signal at VT pin.
HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. The
data on 4 bit latch type output pins remain unchanged until new is received..
4.2 Block Diagram
4.3Pin Diagram
8/22/2019 Electonic Wireless and Wired Voting Machine
42/65
42 | P a g e
4.4 Pin Description
8/22/2019 Electonic Wireless and Wired Voting Machine
43/65
43 | P a g e
4.5 Approximate internal connection circuits
4.6 Absolute Maximum Ratings
Supply Voltage ..........................................0.3V to 13VStorage Temperature ............................50Cto125C
Input Voltage ................................VSS0.3 to VDD+0.3V
Operating Temperature...........................20Cto75C
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute
Maximum Ratings may cause damage to the device. Functional operation of this device at
other conditions beyond those listed in the specification is not implied and prolonged
exposure to extreme conditions may affect device reliability.
4.7 Operation
The 212 series of decoders provides various combinations of addresses and data pins indifferent packages so as to pair with the 2 12 series of encoders .The decoders receive datathat are transmitted by an encoder and interpret the first N bits of code period as addressesand the last 12N bits as data, where N is the address code number. A signal on the DIN pinactivatesthe oscillator which in turn decodes the incoming address and data. The decoders will thencheck the received address three times continuously. If the received address codes allmatch the contents of the decoder local address, the 12N bits of data are decoded to activatethe output pins and the VT pin is set high to indicate a valid transmission. This will lastunless the addresscode is incorrect or no signal is received. The output of the VT pin is high only when thetransmission is valid. Otherwise it is always low.
4.8 Features
Operating voltage: 2.4V~12V
Low power and high noise immunity
8/22/2019 Electonic Wireless and Wired Voting Machine
44/65
44 | P a g e
CMOS technology
Low standby current
Capable of decoding 12 bits of information
Binary address setting
Received codes are checked 3 times
Address/Data number combination
HT12D: 8 address bits and 4 data bits
HT12F: 12 address bits only
Built-in oscillator needs only 5% resistor
Valid transmission indicator
Easy interface with an RF or an infrared transmission medium
Minimal external components
4.9 Applications
Burglar alarm system
Smoke and fire alarm system
Garage door controllers
Car door controllers
Car alarm system
Security system
Cordless telephones
Other remote control systems
5) PRINTED CIRCUIT BOARD (PCB)It is used to mechanically support and electrically connect Electricalcomponents using conductive pathways, tracks or signal traces etched fromcopper sheets laminated onto a non-conductivesubstrate. It is also referred toas printed wiring board (PWB) or etched wiring board. A PCB populated withelectronic components is a printed circuit assembly (PCA), also known asa printed circuit board assembly (PCBA). Printed circuit boards are used invirtually all but the simplest commercially-produced electronic devices.
PCBs are inexpensive, and can be highly reliable. They require much morelayout effort and higher initial cost than either wire wrap or point-to-point
construction, but are much cheaper and faster for high-volume production; theproduction and soldering of PCBs can be done by totally automated equipment.Much of the electronics industry's PCB design, assembly, and quality controlneeds are set by standards that are published by the IPC organization.
8/22/2019 Electonic Wireless and Wired Voting Machine
45/65
45 | P a g e
6) CAPACITORCapacitors are components that are used to store an electrical charge and areused in timer circuits. A capacitor may be used with a resistor to produce atimer. Sometimes capacitors are used to smooth a current in a circuit as theycan prevent false triggering of other components such as relays. When power issupplied to a circuit that includes a capacitor - the capacitor charges up. Whenpower is turned off the capacitor discharges its electrical charge slowly.Thereare two types of capacitors that are
6.1CERAMIC CAPACITOR
A ceramic capacitor is a fixed value capacitorwith the ceramic material acting as
the dielectric. It is constructed of two or more alternating layers ofceramic and
a metal layer acting as the electrodes. The composition of the ceramic material defines the
electrical behavior and therefore the application of the capacitors, which are divided into
two stability classes:
Class 1 ceramic capacitors with high stability and low losses for resonant circuit
application.
Class 2 ceramic capacitors with high volumetric efficiency for buffer, by-pass and
coupling applications.
Ceramic capacitors, especially the multilayer version (MLCC), are the most produced and
used capacitors in electronic equipment with a produced quantity of approximately 1000
billion pieces per year.
http://en.wikipedia.org/wiki/Capacitorhttp://en.wikipedia.org/wiki/Dielectrichttp://en.wikipedia.org/wiki/Ceramichttp://en.wikipedia.org/wiki/Metalhttp://en.wikipedia.org/wiki/Electrodehttp://en.wikipedia.org/wiki/Volumetric_efficiencyhttp://en.wikipedia.org/wiki/Volumetric_efficiencyhttp://en.wikipedia.org/wiki/Electrodehttp://en.wikipedia.org/wiki/Metalhttp://en.wikipedia.org/wiki/Ceramichttp://en.wikipedia.org/wiki/Dielectrichttp://en.wikipedia.org/wiki/Capacitor8/22/2019 Electonic Wireless and Wired Voting Machine
46/65
46 | P a g e
6.2 MYLAR CAPACITOR
A mylar capacitor uses mylar, which is a type of high temperature polyester film, as itsdielectric. It is typically very stable and able to operate over a wide range of temperatures,usually up to 125 degrees Celsius. As such therefore this type is a common choice forinstrumentation equipment, also high quality audio and communications equipment. Theremay be various shapes, sizes and styles of construction but possibly the longest lived andmost recognisable style is the green or brown resin-dipped radial type, which coupled witha small physical size makes it readily suitable for circuit boards.
6.3 Capacitor Code Information
This table is designed to provide the value of alphanumeric coded ceramic, mylar and micacapacitors in general. They come in many sizes, shapes, values and ratings; many differentmanufacturers worldwide produce them and not all play by the same rules. Most capacitorsactually have the numeric values stamped on them, however, some are color coded and
8/22/2019 Electonic Wireless and Wired Voting Machine
47/65
47 | P a g e
some have alphanumeric codes. The capacitor's first and second significant number IDsand are the first and second values, followed by the multiplier number code, followed bythe percentage tolerance letter code. Usually the first two digits of the code represent thesignificant part of the value, while the third digit, called the multiplier, corresponds to thenumber of zeros to be added to the first two digits. After that, the differences may show up.
Use this information as a guideline and at your own risk. If you are in question, try tolocate the original manufacturer and seek information from that source.
VALUE TYPE VALUE TYPE CODE
1.5pF Ceramic 1,000pF / .001uF Ceramic/ Mylar 102
3.3pF Ceramic 1,500pF / .0015uF Ceramic / Mylar 152
10pF Ceramic 2,000pF / .002uF Ceramic / Mylar 202
15pF Ceramic 2,200pF / .0022uF Ceramic / Mylar 222
20pF Ceramic 4,700pF / .0047uF Ceramic / Mylar 472
30pF Ceramic 5,000pF / .005uF Ceramic / Mylar 502
33pF Ceramic 5,600pF / .0056uF Ceramic / Mylar 562
47pF Ceramic 6,800pF / .0068uF Ceramic / Mylar 682
56pF Ceramic .01 Ceramic / Mylar 103
68pF Ceramic .015 Mylar
75pF Ceramic .02 Mylar 203
82pF Ceramic .022 Mylar 223
91pF Ceramic .033 Mylar 333
8/22/2019 Electonic Wireless and Wired Voting Machine
48/65
48 | P a g e
VALUE TYPE CODE VALUE TYPE CODE100pF Ceramic 101 .047 Mylar473
120pF Ceramic 121 .05 Mylar503
130pF Ceramic 131 .056 Mylar563
150pF Ceramic 151 .068 Mylar683
180pF Ceramic 181 .1 Mylar104
220pF Ceramic 221 .2 Mylar204
330pF Ceramic 331 .22 Mylar224
470pF Ceramic 471 .33 Mylar334
560pF Ceramic 561 .47 Mylar474
680pF Ceramic 681 .56 Mylar564
750pF Ceramic 751 1 Mylar105
820pF Ceramic 821 2 Mylar
205
7) Crystal 12 Mhz
An oscillator is something that produces an output that repeats regularly. In theelectronics field this will be an electrical waveform, often but not always a sine
8/22/2019 Electonic Wireless and Wired Voting Machine
49/65
49 | P a g e
wave.
The most important property of an oscillator is its frequency : the rate at which theoutput repeats. This is measured in Hertz (Hz for short). One Hertz is one repetition(aka cycle) per second. One MegaHertz (MHz) is one million repetitions per second.
One of the problems in designing a high quality oscillator is maintaining the outputfrequency at the value required. One method is to control it by a quartz crystal; this iscut so that it vibrates mechanically at the design frequency, and is coupled to theelectronics by the piezo-electric effect.
A 12 MHz crystal oscillator is an electronic circuit, whose output frequency iscontrolled by a quartz crystal to repeat 12 million times per second. Note. Oscillatorsdon't have to be electronic. Other examples are a guitar string, a flute or a pendulum.An electronic oscillator is the only one that can be crystal controlled.)
8) LIQUID CRYSTAL DISPLAY (LCD)
8/22/2019 Electonic Wireless and Wired Voting Machine
50/65
50 | P a g e
A liquid crystal display (LCD) is a thin, flat electronic visual display that uses the light
modulating properties of liquid crystals (LCs). LCs do not emit light directly .They are
used in a wide range of applications, including computer monitors, television, instrument
panels, aircraft cockpit displays, signage, etc. They are common in consumer devices such
as video players, gaming devices, clocks, watches, calculators, and telephones. LCDs have
displaced cathode ray tube (CRT) displays in most applications. They are usually more
compact, lightweight, portable, less expensive, more reliable, and easier on the eyes. They
are available in a wider range of screen sizes than CRT and plasma displays, and since theydo not use phosphors, they cannot suffer image burn-in. LCDs are more energy efficient
and offer safer disposal than CRTs. Its low electrical power consumption enables it to be
used in battery-powered electronic equipment.
LCD (Liquid Crystal Display) screen is an electronic display module and find a wide range
of applications. A 16x2 LCD display is very basic module and is very commonly used in
various devices and circuits. These modules are preferred overseven segments and other
multi segment LEDs. The reasons being: LCDs are economical; easily programmable; have
no limitation of displaying special & even custom characters (unlike in seven
segments), animations and so on.
A16x2 LCDmeans it can display 16 characters per line and there are 2 such lines. In thisLCD each character is displayed in 5x7 pixel matrix. This LCD has two registers, namely,
Command and Data.
The command register stores the command instructions given to the LCD. A command is
an instruction given to LCD to do a predefined task like initializing it, clearing its screen,
setting the cursor position, controlling display etc. The data register stores the data to be
http://www.engineersgarage.com/content/seven-segment-displayhttp://www.engineersgarage.com/content/ledhttp://www.engineersgarage.com/content/ledhttp://www.engineersgarage.com/microcontroller/8051projects/create-custom-characters-LCD-AT89C51http://www.engineersgarage.com/microcontroller/8051projects/display-custom-animations-LCD-AT89C51http://www.engineersgarage.com/microcontroller/8051projects/display-custom-animations-LCD-AT89C51http://www.engineersgarage.com/microcontroller/8051projects/create-custom-characters-LCD-AT89C51http://www.engineersgarage.com/content/ledhttp://www.engineersgarage.com/content/seven-segment-display8/22/2019 Electonic Wireless and Wired Voting Machine
51/65
51 | P a g e
displayed on the LCD. The data is the ASCII value of the character to be displayed on the
LCD. Click to learn more about internal structure of a LCD.
8.1 Pin Description:
9) LIGHT EMITTING DIODES (LED)
http://www.engineersgarage.com/insight/how-lcd-workshttp://www.engineersgarage.com/insight/how-lcd-workshttp://www.engineersgarage.com/insight/how-lcd-works8/22/2019 Electonic Wireless and Wired Voting Machine
52/65
52 | P a g e
A light-emitting diode (LED) is a semiconductor light source. LEDs are usedas indicator lamps in many devices, and are increasingly used for lighting.Introduced as a practical electronic component in 1962, early LEDs emittedlow-intensity red light, but modern versions are available acrossthe visible, ultraviolet and infrared wavelengths, with very high brightness.
When a light-emitting diode is forward biased (switched on), electrons are ableto recombine with electron holes within the device, releasing energy in the formof photons. This effect is called electroluminescence and the color of the light(corresponding to the energy of the photon) is determined by the energy gap ofthe semiconductor. An LED is often small in area (less than 1 mm2), andintegrated optical components may be used to shape its radiation pattern. LEDspresent many advantages over incandescent light sources including lowerenergy consumption, longer lifetime, improved robustness, smaller size, fasterswitching, and greater durability and reliability. LEDs powerful enough forroom lighting are relatively expensive and require more precise current and heat
management than compact fluorescent lamp sources of comparable output.
Light-emitting diodes are used in applications as diverse as replacementsfor aviation lighting, automotive lighting (particularly brake lamps, turn signalsand indicators) as well as in traffic signals. The compact size, the possibility ofnarrow bandwidth, switching speed, and extreme reliability of LEDs hasallowed new text and video displays and sensors to be developed, while theirhigh switching rates are also useful in advanced communicationstechnology. Infrared LEDs are also used in the remote control units of manycommercial products including televisions, DVD players, and other domesticappliances.
10) Buzzer:An electric signaling device, such as a doorbell, that makes a buzzing sound. Also we can
say it is an audio signaling device, which may be mechanical, electromechanical,
orpiezoelectric. Typical uses of buzzers and beepers include alarm devices, timers and
confirmation of user input such as a mouse click or keystroke.
http://en.wikipedia.org/wiki/Soundhttp://en.wikipedia.org/wiki/Machinehttp://en.wikipedia.org/wiki/Electromechanicshttp://en.wikipedia.org/wiki/Piezoelectricityhttp://en.wikipedia.org/wiki/Alarm_deviceshttp://en.wikipedia.org/wiki/Timerhttp://en.wikipedia.org/wiki/Timerhttp://en.wikipedia.org/wiki/Alarm_deviceshttp://en.wikipedia.org/wiki/Piezoelectricityhttp://en.wikipedia.org/wiki/Electromechanicshttp://en.wikipedia.org/wiki/Machinehttp://en.wikipedia.org/wiki/Sound8/22/2019 Electonic Wireless and Wired Voting Machine
53/65
53 | P a g e
11) Diode 1N4007
11.1 Features
Diffused Junction
High Current Capability and Low Forward Voltage DropSurge Overload Rating to 30A Peak
Low Reverse Leakage CurrentMechanical DataCase: DO-41Case Material: Molded Plastic. UL Flammability Classification
Rating 94V-0Moisture Sensitivity: Level 1 per J-STD-020DTerminals: Finish - Bright Tin. Plated Leads Solderable per MIL-STD-202,Method 208Polarity: Cathode BandMounting Position: Any
Marking: Type Number
Weight: 0.30 grams (approximate)
8/22/2019 Electonic Wireless and Wired Voting Machine
54/65
54 | P a g e
11.2 Maximum Ratings
Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, deratecurrent by 20%.
Notes:1. Leads maintained at ambient temperature at a distance of 9.5mm from the case.2. Measured at 1.0 MHz and applied reverse voltage of 4.0V DC.3. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied, seeEU Directive 2002/95/EC Annex Notes.
IMPORTANT NOTICE
8/22/2019 Electonic Wireless and Wired Voting Machine
55/65
55 | P a g e
Diodes Incorporated and its subsidiaries reserve the right to make modifications,enhancements, improvements, corrections or other changes without further notice toany product here in. Diodes Incorporated does not assume any liability arising out ofthe application or use of any product described herein; neither does it convey anylicense under its patent rights, nor the rights of others. The user of products insuch
applications shallassume all risks of such use and will agree to hold Diodes Incorporated and all thecompanies whose products are represented onour website, harmless against alldamages.
11.3 LIFE SUPPORT
Diodes Incorporated products are not authorized for use as critical components in lifesupport devices or systems without the expressed written approval of the President ofDiodes Incorporated .
11.4 ELECTRICAL CHARACTERISTICS
8/22/2019 Electonic Wireless and Wired Voting Machine
56/65
56 | P a g e
12) RANDOM WIRE ANTENNA
8/22/2019 Electonic Wireless and Wired Voting Machine
57/65
57 | P a g e
A random wire antenna is a radio antenna consisting of a long wire suspended above the
ground, whose length does not bear a relation to the wave length of the radio waves used,
but is typically chosen more for convenience. The wire may be straight or it may be strung
back and forth between trees or walls just to get enough wire into the air; this type of
antenna sometimes is called a zig-zag antenna. Such antennas are usually not as effective as
antennas whose length is adjusted to resonate at the wavelength to be used. Random wireantennas are a type ofmonopole antenna and the other side of the receiver or transmitter
antenna terminal must be connected to an earth ground.They are widely used as receiving
antennas on the long wave, medium wave, and short wavebands, as well as transmitting
antennas on these bands for small outdoor, temporary or emergency transmitting stations,
as well as in situations where more permanent antennas cannot be installed.
Often random wire antennas are also referred to as long-wire antenna. Long-wire antennas
require a length greater than a quarter-wavelength (/4) of the radio waves.
13)BERG CONNECTORA Berg connector is a device used to join electrical and electronics circuits .
http://en.wikipedia.org/wiki/Antenna_(radio)http://en.wikipedia.org/wiki/Wavelengthhttp://en.wikipedia.org/wiki/Resonancehttp://en.wikipedia.org/wiki/Wavelengthhttp://en.wikipedia.org/wiki/Monopole_antennahttp://en.wikipedia.org/wiki/Ground_(electricity)http://en.wikipedia.org/wiki/Long_wavehttp://en.wikipedia.org/wiki/Medium_wavehttp://en.wikipedia.org/wiki/Short_wavehttp://en.wikipedia.org/wiki/Short_wavehttp://en.wikipedia.org/wiki/Medium_wavehttp://en.wikipedia.org/wiki/Long_wavehttp://en.wikipedia.org/wiki/Ground_(electricity)http://en.wikipedia.org/wiki/Monopole_antennahttp://en.wikipedia.org/wiki/Wavelengthhttp://en.wikipedia.org/wiki/Resonancehttp://en.wikipedia.org/wiki/Wavelengthhttp://en.wikipedia.org/wiki/Antenna_(radio)8/22/2019 Electonic Wireless and Wired Voting Machine
58/65
58 | P a g e
These connectors typically have either two pins or four, and are used for many purposes.Computers in the late 1980s often had dozens of Berg connectors completing circuits inseveral different areas. On the other hand, more recent computers primarily use other typesof connectors, such as Molex, SATA, or P1.Most connectors are keyed to prevent incorrect mating. In other words, a physical
component prevents people from connecting it backwards or to a different plug. This isimportant because improper connections can break or bend the pins or damage thecomputer. Nevertheless, high amounts of pressure can break the key mechanism and forcea bad connection.
*********
8/22/2019 Electonic Wireless and Wired Voting Machine
59/65
59 | P a g e
OPERATION6.1 Operation or Working of Project:
1] Power on: When supply is turned on RED LED glows.
2] Mode selection:
i. Voting mode: toggle switch on VCC
ii. Counting mode: toggle switch on GND.
Voting Mode: When toggle switch is in voting mode Voting mode is displayed followed
by
Please vote. After a vote being given, Please wait for authority switch is displayed andagain
enable for voting after Control switch being pressed by the voting Authority.
Counting Mode: When toggle switch is in counting mode Counting mode in displayed
on the
screen, and total number of votes to respective candidate can be displayed on the screen by
pressing the respective key assigned to them.
3] Clear mode: Press clear switch when all entries are required to be erased. Clear switch
shouldbe pressed before voting procedure.
4] Buzzer indication: Pressing of key in voting mode is indicated by a buzzer sound.
5] Controller switch: This switch is provided for enabling the keypad in voting mode. This
switch is under the control of voting authority.
8/22/2019 Electonic Wireless and Wired Voting Machine
60/65
60 | P a g e
***************
8/22/2019 Electonic Wireless and Wired Voting Machine
61/65
61 | P a g e
***************
8/22/2019 Electonic Wireless and Wired Voting Machine
62/65
62 | P a g e
***************
ADVANTAGES AND APPLICATIONS
8/22/2019 Electonic Wireless and Wired Voting Machine
63/65
63 | P a g e
9.1 ADVANTAGES:
1.It is economical
2. Less manpower required
3. Time conscious, as less time required for voting & counting4. Avoids invalid voting
5. Saves transportation cost due to its compact size
6. Convenient on the part of voter
9.2 APPLICATIONS:
This could be used for voting purpose at any required place
***************
8/22/2019 Electonic Wireless and Wired Voting Machine
64/65
64 | P a g e
CONCLUSION AND FUTURE WORK
In this report, we have described the specification and architecture of a ELECTRONIC
VOTING
MACHINE .Various fault-tolerance and security issues are delegated to the platform itself,
therefore relieving the application designer from accommodating these features in the
application
design itself. This approach allows for the easy development and deployment of
applications.
For quite some time, voting equipment vendors have maintained that their systems are
secure,
and that the closed-source nature makes them even more secure. Our glimpse into the code
of
such a system reveals that there is little difference in the way code is developed for voting
machines relative to other commercial endeavors. In fact, we believe that an open processwould
result in more careful development, as more scientists, software engineers, political
activists, and
others who value their democracy would be paying attention to the quality of the software
that is
used for their elections. (Of course, open source would not solve all of the problems with
electronic elections. It is still important to verify somehow that the binary program images
running in the machine correspond to the source code and that the compilers used on the
source
code are non-malicious. However, open source is a good start.) Such open design processes
haveproven successful in projects ranging from very focused efforts, such as specifying the
Advanced
Encryption Standard (AES) [23], through very large and complex systems such as
maintaining
the Linux operating System. Australia is currently using an open source voting
system10Alternatively, security models such as the voter-verified audit trail allow for
electronic
voting systems that produce a paper trail that can be seen and verified by a voter. In such a
system, the correctness burden on the voting terminals code is significantly less as voters
cansee and verify a physical object that describes their vote. Even if, for whatever reason, the
machines cannot name the winner of an election, then the paper ballots can be recounted,
either
mechanically or manually, to gain progressively more accurate election results. Voter-
verifiable
audit trails are required in some U.S. states, and major DRE vendors have made public
8/22/2019 Electonic Wireless and Wired Voting Machine
65/65
statements that they would support such features if their customers required it. The EVM
project
an ambitious attempt to create an open-source voting system with a voter-verifiable audit
trail
a laudable goal The model where individual vendors write proprietary code to run our
electionsappears to be unreliable, and if we do not change the process of designing our voting
systems,
we will have no confidence that our election results will reflect the will of the electorate.
We owe
it to ourselves and to our future to have robust, well-designed election systems to preserve
the
bedrock of our democracy.
REFERENCE
top related