Transcript
A complete range of professional
hydraulic and mechanical tools
for the bolting industry
Bolting SolutionsE410
www.enerpac.comiviv
212
Enerpac Bolting Tools
Joint AssemblyFrom simple pipe alignment to complex joint positioning of large structural assemblies, our comprehensive line of joint assembly products range from hydraulic and mechanical alignment tools to PLC-controlled multi-point positioning systems.
Controlled TighteningEnerpac offers a variety of controlled tightening options to best meet the requirements of your application. From mechanical torque multipliers to hydraulically driven square drive wrenches, and from low profile torque wrenches to inter-connectable bolt tensioning tools; we offer the products you need for accurate and simultaneous tightening of multiple bolts.
Joint SeparationEnerpac also provides hydraulic nut splitters and a variety of mechanical and hydraulic spreading tools for joint separation during inspection, maintenance and decommissioning operations.
High quality bolting solutions from the brand you can trust. See how Enerpac can make your bolting work-flow more accurate, safer and efficient.
ENERPAC'S Bolting Solutions caters to the complete bolting work-flow, ensuring joint integrity in a variety of applications throughout industry:
Bolting Integrity Software
Visit www.enerpac.com to access our free on-line bolting software
application and obtain information on tool selection, bolt load calculations and tool pressure settings. A combined application data sheet and joint completion report is also available.
All information in this catalog can be changed due to product improvements without prior notice.
1
�
���� �
��
���
�
��
���
����
���
���
2
4 6 12 20 24 28 29 30 34 36 41 42 43 44
4647
48495051
5455586061
ESWSQDHXD
PMUZU4PTAZA4T
GT
ATPHPT
SCESSATM
NCNCFSM/FSHFSA, WR
Table of Contents
INTRODUCTION AND CAPABILITIES
Bolting Solutions – Product Range Overview
CONTROLLED TIGHTENING AND LOOSENING
Torque Tools
• Manual Torque Wrench Multipliers
• Hydraulic Square Drive Wrenches and Accessories, Steel
• Hydraulic Hexagon Wrenches and Accessories, Steel
• Hydraulic Square Drive Wrenches, Aluminum
• Hydraulic Hexagon Cassette Wrenches, Aluminum
Torque Pumps
• Selection Matrix
• Portable Electric Torque Wrench Pump
• Electric Torque Wrench Pumps
• Compact Pneumatic Torque Wrench Pumps
• Air Driven Torque Wrench Pumps
Tensioning Tools
• Hydraulic Bolt Tensioners
Tensioning Pumps
• Air Pump
• Portable Hand Pump
JOINT ASSEMBLY AND POSITIONING
Cylinder Sets
Synchronized Positioning
Flange Alignment Tools
JOINT SEPARATION
Hydraulic Nut Cutters
Industrial Spreaders
Flange Spreaders
Wedgies and Spread Cylinders
YELLOW PAGES, TECHNICAL INFORMATION
Bolting Theory
Torque Tightening
Tensioning
Nut and Bolt Sizes
Key to Measurement
Tool Type and Functions Series Page
2
ATM – Flange Alignment Tools
E-Series, Manual Torque Multipliers
S and W Series Torque Wrenches
SQD and HXD Series Torque Wrenches
2 www.enerpac.com
Misaligned joints
Joints must be pulled together and correctly aligned prior to tightening. Current methods of manipulation tend to be dangerous and involve a high degree of manual lifting using slings, hooks and lifting gear. These methods can damage joint components, are time consuming in setup and disassembly, operational time and the amount of manpower required.
Solution: Flange Alignment Tools
The Enerpac ATM series Flange Alignment Tools are developed to rectify twist and rotational misalignment without additional stress in pipelines. Hydraulic cylinders, jacks and lifting wedges can also be used to assist in positioning and aligning.
Industrial Application
Controlled Tightening of Multiple sized fasteners for industrial applications.
Solution: Hydraulic Torque Wrenches
Professional tools for industrial applications. Truly versatile tools which utilize standard Impact Sockets, optional direct Allen Drives or Interchangeable cassettes to provide controlled tightening of multiple sized fasteners per tool. Optional accessories further extend the application range of these products.
General Applications
Controlled Tightening of Multiple sized fasteners.
Solution: Hydraulic Torque Wrenches
Lightweight aluminum tools for controlled bolting.
Controlled tightening when external power is unavailable
Applications are often located where external power sources to drive air or electric powered tools are unavailable but controlled bolting is required, typically at values higher than an operator can generate using manual wrenches.
Solution: Manual Torque Multipliers
Enerpac E-series manual torque multipliers offer a range of output torques from manual inputs that can easily be achieved by an operator, providing accurate, effi cient torque multiplication for make-up or break-out of joint fasteners.
Bolting Solutions
3
GT Series – Bolt Tensioners
Pumps and Accessories
NC – Hydraulic Nut Cutters
FSH, FSM – Parallel Wedge Spreaders
3
Controlled Bolting
Increasing Health and Safety, Environmental and Productivity requirements demand even and parallel joint closure to ensure a sound assembly, especially on pressure containing vessels. This often requires the simultaneous tightening of multiple fasteners.
Solution: Bolt Tensioners
Enerpac GT Series Bolt Tensioners can achieve accurate preload in single or multiple fastener applications simultaneously, without inducing rotational twist or contending with the uncertainties of friction and lubrication.
Pumps and AccessoriesA wide range of Pumps and Accessories are available including: Manual, Air and Electrically operated pump units, hoses, gauges, manifolds and fi ttings.
For Bolting SolutionsThink Enerpac
Frozen or Corroded Nuts
Often nuts are diffi cult to remove, while loosening using tightening tools is possible it generally requires larger equipment and is time consuming. The use of cutting torches or hammers and chisels can cause damage to the joint components, requires signifi cantly longer setup and operational time and can present a potential safety risk.
Solution: Hydraulic Nut Cutters
Nut splitting with the NC Series Hydraulic Nut Cutters is the safest method. It takes less time and avoids costly damage to joint components. The angled head design fi tted with heavy-duty chisels permits the splitting of nuts on a wide variety of applications.
Joint Separation
Separation of stubborn joints for inspection and maintenance particularly those fi tted with ring grooves or those with external forces acting on them are often diffi cult to separate. The use of hammers and wedges, chain blocks and lever bars can damage joint components and present a potential safety risk.
Solution: Parallel Wedge Spreaders
The FSH, FSM-Series parallel wedge spreaders offer controlled separation without bending or risk of slipping from the joint. The FS series spreaders are ideally suited to fl anged joint applications.
Bolting Solutions
www.enerpac.com
�
4
E290PLUSE291E391E392E393E492E493E494E495
E-Series, Manual Torque Multipliers
• High-efficiency planetary gear sets achieve high output torque from low input torque
• Most models operator protected by anti-backlash device
• Multiplier output accuracy ± 5% of input torque
• Reversible, tighten or loosen bolts
• Reaction bar or reaction plate type
• Angle-of-turn protractor standard on E300 models
• Reaction plate models offer increased versatility with reaction point locations
• E300 and E400 series replaceable shear drives provide overload protection of internal power train (one replacement shear drive is included)
Accurate, Efficient Torque MultiplicationWhen accurate make-up or break-out of stubborn fasteners requires high torque
Shown from left to right: E291, E393, E494
Typical Torque Multiplier Applications
• Locomotives• Power plants
• Pulp and paper mills • Refineries• Chemical plants• Mining and construction• Off-road equipment• Shipyards• Cranes
MTW-250 Manual Torque Wrench
Available to power manual torque multipliers.
Technical information: • 1/2" Square Drive• 45-250 Ft.lbs. (60-330 Nm)
� Enerpac Reaction Bar Torque Multiplier E393 used to manually torque bolts up to 3,200 ft-lbs.
ModelNumber
Torque Multiplier
Type
Reaction Bar
Multiplier
Output Torque Capacity
(Nm)(Ft.lbs)
Reaction Plate
Multiplier
� SELECTION CHART
10151355162529804340298043406780
10845
75010001200220032002200320050008000
5
H
L
D
S1
S2
L
L1 L2
H
D
S1
S2
R
E290PLUSE291E391E392E393E492E493E494E495
6
Manual Torque Multipliers
Wt.
ESeries
Maximum Output Torque:
750-8000 Ft.lbsTorque Ratio:
3:1-52:1
� Angle-of-Turn Protractor
E391, E392 and E393 models include an angle-of-turn protractor (scale) to tighten fasteners using a “torque turn” method. Allows accurate measuring a specific number of degrees of rotation.
� Shearable Square Drive
Provides overload protection on E300- and E400-series multiplier’s power train by shearing at 103-110% of rated capacity. Internal shear pin prevents tool from falling off bolt.
� Selector Pawl Models with anti-backlash
protection have directional selector pawls. Set the pawl for clockwise or counter-clockwise rotation.
Manual Torque Multipliers
Enerpac manual torque multipliers provide efficient
torque multiplication in wide clearance applications and when external power sources are not available. Manual torque multipliers are used in most industrial, construction, and equipment maintenance applications. Hydraulic torque wrenches are better suited for tight tolerance, flange and repetitious bolting applications.
Use Reaction Bar Models:
• where space is limited• where multiple reaction points
are available• when portability is desirable
Use Reaction Plate Models:• above 3200 Ft-lbs. output torque• on flanges and applications
where neighboring bolt or nut is available to react against
• when extreme reaction forces are generated
Reaction Bar Type 1)
CAUTION!
Never use impact type air tools for power driving torque multipliers. Torque multiplier drive train damage will occur.
Multiplier Output Ratio Accuracy:
± 5 %
Input Torque
(Ft.lbs)
Torque Ratio
InputFemaleSquareDrive
S1 (in)
Over-load
Protec-tion
Anti-Back-lash
Dimensions (in)
(lbs)
ModelNumber
Reaction Plate Type 1)
1) E200 and E400-series do not have an Angle-of-Turn Protractor (scale).User must verify manual torque wrench accuracy prior to use to ensure accurate final output torque.
Hydraulic Torque Wrenches
Enerpac offers a complete range of square drive and hexagon cassette torque wrenches.
Output MaleSquare Drive
ReplaceableShear DriveModel No.
NoNoYesYesYesYesYesYesYes
NoNoNoYesYesYesYesYesYes
(Nm) L1 L2 RLD H
Reaction Bar Type 1) Reaction Plate Type 1)
Page:
S2 (in)
308411271219234219234256208
227303200162173162173189154
3 : 13 : 16 : 1
13.6 : 118.5 : 113.6 : 118.5 : 126.5 : 152 : 1
½
½
½
½
½
½
½
½
½
¾
¾
¾
1
1
1
1
1½
1½
2.82.83.94.14.14.94.95.65.8
3.33.34.05.76.55.56.48.7
10.7
8.617.419.619.619.614.014.014.915.2
–––––
5.55.57.07.0
–––––
4.94.93.53.5
–––––
1.31.31.71.9
45.59.018.315.217.219.434.050.3
––E391SDKE392SDKE393SDKE392SDKE393SDKE494SDKE495SDK
www.enerpac.com
�
6
9
Square Drive Hydraulic Torque Wrenches
Rigid Steel Design
The Professional Square Drive Solution
S-Series, Square Drive WrenchesThis product range has been designed using state-
of-the-art CAD techniques to bring you the most advanced square drive torque wrench on the market. To ensure that the tools you buy meet our own exacting requirements, during the design process every prototype was put through finite element stress analysis, photo-elastic modeling, rigorous cyclic testing and strain gauging.
Simplicity• 360° click-on, multi-position reaction arm• Push button square drive release for quickly reversing the
square drive for tightening or loosening• Fine tooth ratchet prevents tool “lock-on”• Single 360° hydraulic swivel manifold, complete with screw
lock couplings, increases wrench and hose maneuverability
Design• Compact, high-strength uni-body construction for a small
operating radius• Robust design with minimal parts enables easy on-site
maintenance without special tools• Lightweight, ergonomic design for easy handling and an
easy fit, even in applications where access is limited• Optimised strength-to-weight ratio• Fast operation due to the large nut rotation per wrench
cycle (35 degree rotation angle) and rapid return stroke
Reliability• All wrenches are nickel-plated for excellent corrosion
protection and improved durability in harsh environments
Accuracy• Constant torque output provides high accuracy across the
full stroke• Uni-body construction ensures accuracy by reducing
internal deflections
From left to right: S3000, S6000, S1500
Torque Wrench Hoses
Use Enerpac THQ-700 Series torque wrench hoses with S-Series torque wrenches to ensure the
integrity of your hydraulic system.
19.5 feet long, 2 hoses39 feet long, 2 hoses
TSP - Pro Series Swivel
Featuring Tilt & Swivel technology the TSP provides 360° X-axis rotation and 160° y-axis rotation.
How to Order
Order an accessory which can be fitted to existing S-Series wrenches.
Factory fitted to new S-Series wrenches: Suffix the wrench model number with "-P" e.g.: S1500-P.
Page:
THQ-706TTHQ-712T
7
A F
D
BC H
G
E
S25000
S3000
S6000
S11000
S1500 28
250%
Double-Acting Square Drive Hydraulic Torque Wrenches
SSeries
Maximum Torque at 10,000 psi:
25,140 Ft.lbsSquare Drive Range:
¾-2½ inchesNose Radius:
.99-2.50 inchesMaximum Operating Pressure:
10,000 psi
Torque Wrench and Pump Selection Matrix
For optimum speed and performance see the torque wrench and pump matrix.
Torque WrenchModel No.Size
(in)
(Ft.lbs)
Maximum Torque
at 10,000 psi
Dimensions (in)
See “Yellow Pages “ section for torque conversions.To order a S-series wrench fitted with the TSP swivel, suffix the model number with "-P". e.g., S1500-P.
(lbs)
Page:
Model No.(included with
wrench)
Square Drive
*TORQUE WRENCH SELECTION (based on socket size range)
�
The rigid steel design of S-Series torque wrenches
guarantee durability, reliability and safety. These wrenches can be powered
by the portable ZU4T-Series pumps.
To
rque
Ran
ge
(Ft.
lbs)
�
Socket Size Range (inch) �
Weight
* Additional socket sizes available upon request.
� Drive Unit� Pro Series Swivel � Reaction Arm� Extended Reaction Arm
� Square Drive� Allen Drive� Short Reaction Arm
Select the Right TorqueChoose your Enerpac Torque Wrench using the untightening rule of
thumb: Loosening torque equals about 250% of tightening torque.
Nm
140032006010
11,00025,140
SD15-012SD30-100SD60-108SD110-108SD250-208
¾"
1"1½"1½"2½"
1.541.892.242.803.43
2.483.033.554.375.63
4.335.287.057.229.61
3.744.966.387.299.46
5.366.787.928.90
11.50
0.991.301.661.952.50
5.9411.0018.7033.0068.20
S1500S3000S6000S11000S25000
2.723.554.415.207.17
4.696.277.378.94
11.50
A B C D FE G H
3690
7380
11,070
14,760
18,450
22,140
25,830
3/4 13/8 23/82 37/8 45/8 61/8
189843398144
14,91434,079
8 www.enerpac.com8
B1
H1
C1
SDA-Series, Allen Drives
For
SSeries
Model Number
Model Number
TORQUE WRENCH
OPTIONAL ALLEN DRIVES,
IMPERIAL
MaximumTorque
(Ft.Lbs)
HexagonSize
(in)
� SELECTION CHART
Dim.
B1(in)
Model Number
OPTIONAL ALLEN DRIVES,
METRIC
SHORT REACTION ARM FOR
ALLEN DRIVES
MaximumTorque
(Ft.lbs)
HexagonSize
(mm)
Model Number
Dim.
B1(in)
Dimensions(in)
S1500(1400 Ft-lbs)
S3000(3200 Ft-lbs)
S6000(6000 Ft-lbs)
S11000(11,000 Ft-lbs)
S25000(25,000 Ft-lbs)
Maximum Torque at 10,000 psi:
25.140 Ft.lbs.
Hexagon Size Allen Drive:
14-85 mm
� Drive Unit� Pro Series Swivel � Reaction Arm� Extended Reaction Arm� Square Drive� Allen Drive� Short Reaction Arm
Square Drive Range:
¾-2½ inches
SDA15-008SDA15-010SDA15-012SDA15-014SDA15-100
355690119514001400
½
⅝
¾
7�8
1
2.62.62.82.93.0
SDA30-010SDA30-012SDA30-014SDA30-100SDA30-102SDA30-104–
69011951895282532003200
–
⅝
¾
7�8
11⅛
1¼
–
3.03.13.33.43.53.5–
SDA60-010SDA60-012SDA60-014SDA60-100SDA60-102SDA60-104–
69011951895282540255520
–
⅝
¾
7�8
11⅛
1¼
–
3.33.53.63.73.83.9–
SDA110-104SDA110-106SDA110-108SDA110-110SDA110-112
552073459535
11,00011,000
1¼
13/8
1½
1⅝
1¾
4.54.64.64.84.9
SDA250-108SDA250-110SDA250-112SDA250-114SDA250-200SDA250-204––––
953512,12015,13518,62022,59525,150
––––
1½
1⅝
1¾
17�8
22¼
––––
5.55.75.85.95.96.0––––
SDA15-14SDA15-17SDA15-19SDA15-22SDA15-24
SRA15
475850
118413991399
1417192224
2.602.682.762.872.91
2.66 2.56
C1 H1
SDA30-17SDA30-19SDA30-22SDA30-24SDA30-27SDA30-30SDA30-32
SRA30
850118518352385320032003200
17192224273032
3.033.113.233.313.353.433.46
3.15 2.91
SDA60-17SDA60-19SDA60-22SDA60-24SDA60-27SDA60-30SDA60-32
SRA60
850118518352385339546555650
17192224273032
3.393.463.583.663.703.783.82
3.60 3.50
SDA110-30SDA110-32SDA110-36SDA110-41SDA110-46
SRA110
465556508040
11,00011,000
3032364146
4.414.494.614.765.00
5.02 4.17
SDA250-36SDA250-41SDA250-46SDA250-50SDA250-55SDA250-60SDA250-65SDA250-70SDA250-75SDA250-85
SRA250
8040118801677521,54525,15025,15025,15025,15025,15025,150
36414650556065707585
5.515.675.835.946.066.226.346.466.616.89
6.24 5.31
99
BA DC
DAS1500S3000S6000S11000S25000
SRS151SRS152SRS153SRS301SRS302SRS303SRS601SRS602SRS603SRS1101SRS1102SRS1103SRS2501SRS2502SRS2503
CD
B
A
A
D
RTE15RTE30RTE60 RTE110 RTE250
S1500, S3000S6000, S11000, S25000
TSP100TSP200
S1500
S3000
S6000
S11000
S25000
A C DB
°B
C
D
1/4" - 18 NPTF
°
S-Series Accessories
• Pro Series Swivel featuring Tilt and Swivel technology• 360 degree X-axis and 160 degree Y-axis rotation• 10,000 psi / 700 bar maximum working pressure• Increases tool fit in restricted access areas• Simplifies hose placement
• Reaction Tube Extension for S-Series Wrenches• Full torque rated• Increases tool fit in restricted access areas
• Extended Reaction Arms• Lightweight interchangeable design• Can be used with Long Reach Sockets
Model Number
Dimensions (in) Weight
(lbs)
Model Number
Max. Torque(Ft-lbs)
Wrench Model
Weight(lbs)
Dimensions (in) Weight
(lbs)
Wrench Model
Model Number
Wrench Model
Dimensions (in)
TSP Series
RTE Series
SRS Series
To order a S-series wrench fitted with the TSP swivel, suffix the model number with "-P". e.g., S1500-P.
2.522.64
.41.43
1 .061.06
.911.02
1.601.65
25.0025.4725.9526.5826.98
10.1912.1517.0024.7138.12
2.282.242.562.993.94
2.24
2.57
3.11
3.70
4.84
5.596.597.596.617.618.618.079.07
10.079.15
10.1511.1511.3012.3013.30
132812101131289027382636578454985292
10805102949877
247362363822680
1.21.51.92.42.93.44.24.95.57.58.79.8
13.615.417.1
1.45
2.89
3.91
5.24
5.82
1.48
1.89
2.30
2.86
3.44
23.62
5.91
www.enerpac.com10
A/F
8
250%
BSH7519BSH75088BSH75094BSH7527BSH7530BSH75125BSH75131BSH7535BSH75144BSH7538BSH75156BSH75163BSH7543BSH75175BSH7546BSH75188BSH75194BSH75200
¾"7�8"
15�16"1 1�16"1 3�16"1 ¼"1 5�16"1 ⅜"1 7�16"1 ½"1 9�16"1 ⅝"
1 11�16"1 ¾"
1 13�16"1 7�8"
1 15�16"2"
BSH1019BSH10088BSH10094BSH1027BSH1030BSH10125BSH10131BSH1035BSH10144BSH1038BSH10156BSH10163BSH1043BSH10175BSH1046BSH10188BSH10194BSH10200BSH10206BSH10213BSH10219BSH10225
¾"7�8"
15�16"1 1�16"1 3�16"1 ¼"1 5�16"1 ⅜"1 7�16"1 ½"1 9�16"1 ⅝"
1 11�16"1 ¾"
1 13�16"1 7�8"
1 15�16"2"
2 1�16"2 ⅛"2 3�16"2 ¼"
BSH10231BSH10238BSH10244BSH10250BSH1065BSH10263BSH10269BSH1070BSH10281BSH10288BSH1075BSH10300BSH10306BSH10313BSH10319BSH10325BSH10338BSH10350BSH10363BSH1095BSH10388
2 5�16"2 ⅜"2 7�16"2 ½"2 9�16"2 ⅝"
2 11�16"2 ¾"
2 13�16"2 7�8"2 15�16
3"3 1�16"3 ⅛"3 3�16"3 ¼"3 ⅜"3 ½"3 5�8"3 ¾"3 7�8"
BSH15144BSH1538BSH15156BSH15163BSH1543BSH15175BSH1546BSH15188BSH15194BSH15200BSH15206BSH15213BSH15219BSH15225BSH15231BSH15238BSH15244BSH15250BSH1565BSH15263BSH15269BSH1570
1 7�16"1 ½"1 9�16"1 5�8"
1 11�16"1 ¾"
1 13�16"1 7�8"
1 15�16"2"
2 1�16"2 ⅛"2 3�16"2 ¼"2 5�16"2 3�8"2 7�16"2 ½"2 9�16"2 ⅝"
2 11�16"2 ¾"
BSH15281BSH15288BSH1575BSH15300BSH15306BSH15313BSH15319BSH15325BSH15338BSH15350BSH15363BSH1595BSH15388BSH15100BSH15400BSH15105BSH15419BSH15425BSH15110BSH15438BSH15450BSH15463
2 13�16"2 7�8"
2 15�16"3"
3 1�16"3 ⅛"3 3�16"3 ¼"3 ⅜"3 ½"3 ⅝"3 ¾"3 7�8"
3 15�16"4"
4 ⅛"4 3�16"4 ¼"4 5�16"4 ⅜"4 ½"4 ⅝"
BSH25244BSH25250BSH2565BSH25263BSH25269BSH2570BSH25281BSH25288BSH2575BSH25300BSH25306BSH25313BSH25319BSH25325BSH25338BSH25350BSH25363BSH2595BSH25388BSH25100BSH25400BSH25105
BSH25419BSH25425BSH25110BSH25438BSH25450BSH25463BSH25475BSH25488BSH25500BSH25513BSH25519BSH25525BSH25538BSH25140BSH25575BSH25150BSH25600BSH25613
4 13�16"4 ¼"4 5�16"4 3�8"4 ½"4 ⅝"4 ¾"4 7�8"
5"5 1�8"5 3�16"5 ¼"5 ⅜"5 ½"5 ¾"5 7�8"
6"6 1�8"
2 7�16"2 ½"2 9�16"2 ⅝"
2 11�16"2 ¾"
2 13�16"2 7�8"
2 15�16"3"
3 1�16"3 ⅛"3 3�16"3 ¼"3 ⅜"3 ½"3 ⅝"3 ¾"3 7�8"
3 15�16"4"
4 ⅛"
BSH7519BSH7524BSH7527BSH7530BSH7532BSH7536BSH75163BSH7546BSH7550
BSH1019BSH1024BSH1027BSH1030BSH1032BSH1036BSH10163BSH1046BSH1050BSH1055BSH1060BSH1065BSH1070BSH1075BSH1080BSH1085BSH1090BSH1095BSH10100
BSH1536BSH15163BSH1546BSH1550BSH1555BSH1560BSH1565BSH1570BSH1575BSH1580BSH1585BSH1590BSH1595BSH15100BSH15105BSH15110BSH15115
BSH2565BSH2570BSH2575BSH2580BSH2585BSH2590BSH2595BSH25100BSH25105BSH25110BSH25115BSH25120BSH25125BSH25135BSH25140BSH25145BSH25150BSH25155
65
70
75
80
85
90
95
100
105
110
115
120
125
135
140
145
150
155
36
41
46
50
55
60
65
70
75
80
85
90
95
100
105
110
115
19
24
27
30
32
36
41
46
50
55
60
65
70
75
80
85
90
95
100
19
24
27
30
32
36
41
46
50
A/F(in)
IMPERIAL SOCKETS
3/4" Square Drive 1" Square Drive 1 1/2" Square Drive
Model Number
2 1/2" Square Drive
A/F(in)
Model Number
A/F(in)
Model Number
A/F(in)
Model Number
A/F(in)
Model Number
A/F(in)
Model Number
A/F(in)
Model Number
A/F(mm)
3/4" Square Drive 1" Square Drive 1 1/2" Square Drive
Model Number
2 1/2" Square Drive
A/F(mm)
Model Number
A/F(mm)
Model Number
A/F(mm)
Model Number
METRIC SOCKETS
BSH-Series Sockets
BSH Series Sockets• Heavy-duty impact sockets• Supplied with "Pin and Ring"
Optional Allen Drives
Expanded versatility with a wide range of metric and imperial Allen drives.
Page:
Pin and RingAll sockets are supplied with a "Pin and Ring" to hold the socket in place on the square
drive of the tool.
Select the Right Torque
Choose your Enerpac Torque Wrench using the untightening rule of thumb:
Loosening torque equals about 250% of tightening torque.
Square Drive
11
F
D
H
G
E
C
H
A
G
F
E
B
FD
HG
E
Bolting Application Ideas
S6000 on a High Volume Pump Unit
High vibration requires long studs to be accurately tightened to the calculated preload.
During maintenance quick turnaround times are essential; S Series wrenches are chosen as they provide a large
angle of nut rotation per stroke, offering speed and accuracy in compact ergonomic tool.
ENERPAC professional series steel torque
wrenches provide reliable controlled tightening
solutions across Industry.
S3000 Square Drive Torque Wrench on Wind Tower erection and maintenance
S3000 used to connect wind tower segments during assembly and maintenance. A robust but compact solution
is required for tightening of bolts on wind tower sections. Large numbers of fasteners require precise application of
torque to ensure joint integrity is achieved and maintained.
The Enerpac S-Series wrench was selected as it offers simple and reliable operation while providing accurate
and repeatable results.
W4000 Low Profile Torque Wrench on an ANSI Pipe Flange
Throughout the Oil and Gas, Petrochemical and Processing Industries, pipeline joints, valves, pumps and machinery present challenges for controlled bolting.
The restricted access on this pipeline elbow was easily overcome by the selection of an Enerpac W-Series Torque Wrench. A member of the professional series steel torque wrench family the W Wrenches offer reliability and control ensuring even and consistent torque is applied to all bolts.
www.enerpac.com
�
12
19
W-Series, Low Profile Hexagon Wrenches
Rigid Steel Design
The Professional Low Profile Solution
Shown: Drive units with interchangeable cassettes
Simplicity• No tools are needed for changing the hexagon cassettes• Innovative, pinless wrench construction incorporates quick
release cylinder and automatic crank engagement• Single 360° hydraulic swivel manifold complete with screw lock
couplings increases wrench and hose manueverability
Design• Cylinders and low profile cassettes have been engineered to give
ultra slim, compact low clearance tooling with a small nose radius• Robust design with minimal parts enables easy on-site
maintenance without special tools• Nut sizes covered range from 1⅛ - 4⅝ inch (30 - 115 mm)• Optimized strength-to-weight ratio• Fast operation due to the large nut rotation per wrench cycle
(30 degree rotation angle) and rapid return stroke
Reliability• All wrenches are nickel-plated for excellent corrosion protection
and improved durability in harsh environments• All wrenches are fitted with bronze bushings to ensure the ratchet
will never seize in the sideplates, thus eliminating costly repairs
Accuracy• Constant torque output provides high accuracy across
the full stroke• In-line reaction foot ensures accuracy by reducing
internal deflections
W-Series, Low Profile Torque WrenchesThis product range has been designed using state-of-the art
CAD techniques to bring you the most advanced low profile torque wrench on the market. Safety, quality, toughness and reliability are built in.
During the design process every prototype was put through finite element stress analysis, photo-elastic modelling, rigorous cyclic testing and strain gauging.
Torque Wrench Hoses
Use Enerpac THQ-700 Series hoses with W-Series torque wrenches to ensure the integrity of your hydraulic system.
19.5 feet long, 2 hoses39 feet long, 2 hoses
TSP - Pro Series Swivel
Featuring Tilt and Swivel technology the TSP provides 360° X-axis rotation and 160° Y-axis rotation.
How to Order
Order an accessory which can be fitted to existing W-Series wrenches.
Factory fitted to new W-Series wrenches: Suffix the wrench model number with "-P" e.g.: W2000-P.
Page:
THQ-706TTHQ-712T
13
D CH
A
G
F E
B
S
W2000
W4000
W8000
W15000
28
14
18
Double-Acting Hydraulic Hexagon Torque Wrenches
Hexagon Cassettes and Reducer Inserts
Maximum versatility with the full range of interchangeable hexagon cassettes
and hexagon reducing inserts is available in metric and inch sizes.
WSeries
Maximum Torque at 10,000 psi:
15,000 Ft.lbsHexagon Range:
1⅛ -4⅝ inchesNose Radius:
1.22-3.44 inchesMaximum Operating Pressure:
10,000 psi
Torque Wrench Pump Selection Matrix
For optimum speed and performance see the torque wrench and pump matrix.
� SELECTION CHART
Hexagon Range * Maximum Torque
at 10,000 psi
(mm)(in) (Ft.lbs)
Drive Unit Model Number
MinimumTorque
(Ft.lbs)
Dimensions (see pages 14-18 for dimensions H, G and S)
(in)
WeightDrive unitwithout hexagoncassette
(lbs)
* With in-line reaction foot. To order a W-series wrench fitted with the TSP swivel, suffix the model number with "-P". e.g., W2000-P.
Page:
Page:
� These rigid steel wrenches with low profile interchangeable hexagon cassettes guarantee durability and maximum versatility in bolting applications.
To
rque
Ran
ge
(Ft.
lbs)
�
Hexagon Size Range (inch) �
DRIVE UNIT AND INTERCHANGEABLE CASSETTE SELECTION
� Hexagon Cassette� Drive Unit � Pro Series Swivel
� Extended Reaction Arm� Reducer Insert� Reaction Paddle
Page:
(Nm) (Nm)
30 - 6036 - 8550 - 10565 - 115
1⅛ - 2⅜
15�16 - 3⅜
17⁄8 - 4⅛
27�16 - 4⅝
200040008000
15,000
W2000W4000W8000W15000
200400800
1500
4.295.356.778.15
5.556.578.079.45
5.837.018.199.96
1.261.612.072.48
3.094.416.6111.02
A B C D
.941.291.651.97
E
.79
.79
.98
.79
F
0
1475
2950
4425
5900
7375
8850
10,325
11,800
13,275
14,750
16,225
17/16 23/423/16 31/8 37/8 45/8
27125423
10,84620,337
271542
10842033
www.enerpac.com14
W2102W2103W2104W2105W2106W2107W2108W2109W2110W2111W2112W2113W2114W2115W2200W2201W2202W2203–W2204W2205W2206–
H GS
–––––W2107R102––W2110R104––W2113R107––W2200R110––W2203R113–––W2206R200W2206R108
––––––––W2110R103––W2113R104––W2200R107––W2203R110–––W2206R114W2206R107
–––––––––––––––––W2203R107–––W2206R113–
W20
00WSeries
Maximum Torque at 10,000 psi:
2000 Ft.lbsHexagon Range:
1⅛-2⅜ inchesMaximum Operating Pressure:
10,000 psi
Optional Hexagon Reducing Insert (see pages 14-18)
Drive Unit
Interchangeable Hexagon Cassette
W2000 Series Imperial Cassettes & Reducer Inserts
� SELECTION CHART
HexagonSize
S
(in)
Drive Unit Model
Number
Model Number
Nose Radius
H
(in)
Weight
(lbs)
HexagonReducer
(in)
Model Number
Model Number
HexagonReducer
(in)
Model Number
HexagonReducer
(in)
G
(in)
1.221.221.221.221.221.221.321.321.321.441.441.441.541.541.541.651.651.65
–1.751.751.75
–
1⅛
13�16
1¼
15�16
1⅜
17�16
1½
19/16
1⅝
111�16
1¾
113�16
17�8
115/16
2
21⁄16
2⅛
23�16
–2¼
25�16
2⅜–
2.112.112.112.112.112.112.292.292.292.382.382.382.482.482.482.702.702.70
–2.552.552.55
–
–––––
17�16 - 1⅛
––
1⅝ - 1¼
––
113�16 - 17/16
––
2 - 1⅝
––
23�16 - 113�16
–––
2⅜ - 22⅜ - 1½
––––––––
1⅝ - 13�16
––
113�16 - 1¼
––
2 - 17/16
––
23�16 - 1⅝
–––
2⅜ - 17�8
2⅜ - 17�16
–––––––––––––––––
23�16 - 17�16
–––
2⅜ - 113�16
–
0.950.950.950.950.950.950.990.990.990.990.990.990.990.990.991.041.041.04
–1.001.001.00
–
15
W4105W4106W4107W4108W4109W4110W4111W4112W4113W4114W4115W4200W4201W4202W4203W4204W4205W4206–W4207W4208W4209–W4210W4211W4212W4213W4214W4215–W4300W4301W4302––W4303W4304W4305W4306
––––––––
––W4200R107––W4203R110––W4206R200R4206R106W4207R200W4208R200W4209R203W4209R200––W4212R206––W4215R209W4215R200W4300R203–W4302R212W4302R205W4302R202––––
––––––––––––––W4203R107––W4206R113––W4208R113W4209R202W4209R113––W4212R203––W4215R206–––W4302R209W4302R204W4302R200 ––––
–––––––––––
––W4203R104––W4206R107–––W4208R201–––W4212R202––W4215R203–––W4302R206W4302R203
––––
W40
00
H GS
� SELECTION CHART
W4000 Series Imperial Cassettes & Reducer Inserts
WSeries
Maximum Torque at 10,000 psi:
4000 Ft.lbsHexagon Range:
15�16-3⅜ inchesMaximum Operating Pressure:
10,000 psi
HexagonSize
S
(in)
Drive Unit Model
Number
Model Number
Weight
(lbs)
HexagonReducer
(in)
Model Number
Model Number
HexagonReducer
(in)
Model Number
HexagonReducer
(in)
Nose Radius
H
(in)
G
(in)
1.461.461.461.461.461.461.561.561.561.631.631.631.731.731.731.831.831.83
–1.951.951.95
–2.072.072.072.182.182.18
–2.302.302.30
––
2.442.442.442.44
15�16
1⅜
17�16
1½
19�16
1⅝
111/16
1¾
113�16
17�8
115�16
2
21/16
2⅛
23⁄16
2¼
25�16
2⅜
–27/16
2½
29�16
–2⅝
211/16
2¾
213/16
27�8
215�16
–3
31/16
3⅛
––
33�16
3¼
35�16
3⅜
2.402.402.402.402.402.402.522.522.522.632.632.632.892.892.892.782.782.78
–3.003.003.00
–3.083.083.083.213.213.21
–3.293.293.29
––
3.373.373.373.37
–––––––––––
2 - 17�8
––
23�16 - 1⅝
––
2⅜ - 22⅜ - 1⅜
27�16 - 22½ - 2
29�16 - 23�16
29�16 - 2
––
2¾ - 2⅜
––
215/16 - 29�16
215/16 - 23 - 23�16
–3⅛ - 2¾
3⅛ - 25�16
3⅛ - 2⅛
––––
––––––––––––––
23�16 - 17�16
––
2⅜ - 113⁄16
––
2½ - 113�16
29�16 - 2⅛
29�16 - 213�16
––
2¾ - 23�16
––
215/16 - 2⅜
–––
3⅛ - 29�16
3⅛ - 2¼
3⅛ - 2––––
––––––––––––––
23�16 - 1¼
––
2⅜ - 17�16
–––
29�16 - 21�16
–––
2¾ - 2⅛
––
215�16 - 23�16
–––
3⅛ - 2⅜
3⅛ - 23/16
–––––
1.681.681.681.681.681.681.721.721.721.771.771.771.811.811.811.861.861.86
1.861.861.86
1.911.911.911.951.951.95
2.002.002.00
2.042.042.042.04
www.enerpac.com16
W8114W8115W8200W8201W8202W8203W8204W8205W8206W8207W8208W8209W8210W8211W8212W8213W8214W8215W8300W8301W8302–W8303W8304W8305W8306W8307IW8308W8309W8310W8311W8312W8313W8314W8315W8400W8401IW8402
–––––––––––W8209R200––W8212R203––W8215R206––W8302R209W8302R200–––––W8308R300–––W8312R302–W8314R302––––
–––––––––––––––––W8215R203––W8302R206––––––W8308R215–––W8312R215–W8314R215––––
–––––––––––
––
––
––W8302R203
–––––W8308R212–––W8312R212––––––
W80
00
www.enerpac.com
H GS
� SELECTION CHART
HexagonSize
S
(in)
W8000 Series Imperial Cassettes & Reducer Inserts
Maximum Torque at 10,000 psi:
8000 Ft.lbsHexagon Range:
17�8 -4⅛ inchesMaximum Operating Pressure:
10,000 psi
Drive Unit Model
Number
Model Number
Weight
(lbs)
HexagonReducer
(in)
Model Number
Model Number
HexagonReducer
(in)
Model Number
HexagonReducer
(in)
WSeries
Nose Radius
H
(in)
G
(in)
1.771.771.771.891.891.892.012.012.012.072.072.072.202.202.202.282.282.282.382.382.38
–2.602.602.602.602.602.602.912.912.912.912.912.913.133.133.133.13
17/8
115/16
2
21/16
2⅛
23/16
2¼
25�16
2⅜
27�16
2½
29�16
2⅝
211�16
2¾
213/16
27�8
215�16
3
31/16
3⅛
–33�16
3¼
35/16
33/8
37⁄16
3½
39/16
35�8
311�16
3¾
313/16
37�8
315/16
441/16
4⅛
–––––––––––
29�16 - 2––
2¾ - 23�16
––
215/16 - 2⅜
––
3⅛ - 29�16
3⅛ - 2–––––
3½ - 3–––
3¾ - 3⅛
–37�8 - 3⅛
––––
–––––––––––
––
––
215�16 - 23�16
––
3⅛ - 2⅜
––––––
3½ - 215�16
–––
3¾ - 215�16
–37�8 - 215�16
––––
–––––––––––
––
–––––
3⅛ - 23/16
––––––
3½ - 2¾
–––
3¾ - 2¾
––––––
3.683.683.683.683.683.683.683.683.683.683.683.683.683.583.583.583.583.583.633.633.63
–3.723.723.723.723.723.723.993.993.993.993.993.994.224.224.224.22
3.083.083.083.153.153.153.253.253.253.383.383.383.343.343.343.353.353.353.523.523.52
–3.633.633.633.633.633.634.054.054.054.054.054.054.334.334.334.33
17
W15207W15208W15209W15210W15211W15212W15213W15214W15215W15300W15301W15302W15303W15304W15305W15306W15307IW15308W15309W15310W15311W15312W15313W15314W15315W15400W15401IW15402W15403IW15404W15405W15406W15407W15408IW15409IW15410I–
–––––––––W15300R202–W15302R209–––––W15308R215–––W15312R302–W15314R302–––W15402R308–W15404R308–––––W15410R315W15410R308
–––––––––––––––––W15308R212–––W15312R215–W15314R215–––W15402R305–W15404R302–––––W15410R314–
–––––––––––
–––––––––––––––W15402R304–––––––W15410R312–
W15
000
H GS
� SELECTION CHART
W15000 Series Imperial Cassettes & Reducer Inserts
WSeries
Maximum Torque at 10,000 psi:
15,000 Ft.lbsHexagon Range:
27�16-4⅝ inchesMaximum Operating Pressure:
10,000 psi
HexagonSize
S
(in)
Drive Unit Model
Number
Model Number
Weight
(lbs)
HexagonReducer
(in)
Model Number
Model Number
HexagonReducer
(in)
Model Number
HexagonReducer
(in)
Nose Radius
H
(in)
G
(in)
2.322.322.322.322.322.322.442.442.442.542.542.542.742.742.742.742.742.742.952.952.952.952.952.953.173.173.173.173.173.173.443.443.443.443.443.44
–
27�16
2½
29�16
2⅝
211�16
2¾
213/16
27/8
215�16
3
31�16
3⅛
33/16
3¼
35⁄16
3⅜
37/16
3½
39�16
3⅝
311/16
3¾
313�16
37�8
315�16
4
41�16
4⅛
43�16
4¼
45�16
4⅜
47�16
4½
49�16
45�8
–
3.493.493.493.493.493.493.563.563.563.663.663.663.803.803.803.803.803.804.014.014.014.014.014.014.064.064.064.064.064.064.524.524.524.524.524.52
–
–––––––––
3 - 2⅛
– 3⅛ - 29�16
–––––
3½ - 215�16
–––
3¾ - 3⅛
–37�8 - 3⅛
–––
4⅛ - 3½
–4¼ - 3½
–––––
4⅝ - 315/16
4⅝ - 3½
–––––––––––
–––––
3½ - 2¾
–––
3¾ - 215�16
–37�8 - 215/16
–––
4⅛ - 35/16
–4¼ - 31⁄8
–––––
4⅝ - 37�8
–
–––––––––––
–––––
–––
–––––
4⅛ - 3¼
–––––––
4⅝ - 3¾
–
6.176.176.176.176.176.176.226.226.226.266.266.266.406.406.406.406.406.406.626.626.626.626.586.586.726.726.726.726.726.726.856.856.856.856.856.85
–
www.enerpac.com18
W20
00W
4000
W80
00W
1500
0
W2103W2104W2107W2108W2110W2113W2200W2203W2206–W4107W4110W4113W4200W4203W4206W4209W4212W4215W4215W4302W4302W4085MW8200W8203W8206W8209W8212W8215W8302–W8085M–W8090MW8312W8315W8402W15209W15212W15215W15302W15085MW15090MW15312
W15315W15402W15405W15115M
––––W2110R104W2113R107W2200R110W2203R113W2206R200W2206R107–––W4200R107W4203R110W4206R200W4209R203W4212R206W4215R209W4215R203W4302R215W4302R203––––W8209R200W8212R203W8215R206W8302R209W8302R200W8085R070MW8085R055MW8090R075MW8312R302–––––W15302R209W15085R070MW15090R75MW15312R302
–W15402R090MW15110R095MW15115R100M
––––W2110R103W2113R104W2200R107W2203R110W2206R113–––––W4203R107W4206R113W4209R200W4212R203W4215R206W4215R200W4302R212W4302R200––––––W8215R203W8302R206–W8085R065M––W8312R215––––––
–W15312R215
––––
––––W2110R024M––W2203R107W2206R110–––––W4203R104W4206R107W4209R113–––W4302R209––––––––W8302R203–W8085R060M––––––––––––
––––
H GS
W Series Metric Cassettes and Reducer Inserts
Drive Unit Model
Number
Model Number
HexagonSize
S
(mm)
Weight
(lbs)
HexagonReducer
(mm)
Model Number
Model Number
HexagonReducer
(mm)
Model Number
HexagonReducer
(mm)
Nose Radius
H
(in)
G
(in)
� SELECTION CHART
Maximum Torque at 10,000 psi:
8000 Ft.lbsHexagon Range:
30-115 mmMaximum Operating Pressure:
10,000 psi (700 bar)
WSeries
1.221.221.221.321.321.441.541.651.75
–1.461.461.561.631.731.831.952.072.18
–2.30
–2.441.771.892.010.092.072.282.38
–2.60
–2.912.913.133.132.322.322.442.542.742.952.95
3.173.173.443.44
30
3236384146505560–
364146505560657075–
80–
8550556065707580–
85–
909510010565707580859095
100105110115
2.112.112.112.292.292.382.482.702.55
–2.402.402.522.632.892.783.003.083.21
–3.29
–3.373.083.153.253.383.343.353.52
–3.63
–4.054.054.334.333.493.493.563.663.804.014.01
4.064.064.524.52
––––
41 - 3246 - 3650 - 4155 - 4660 - 5060 - 36
–––
50 - 3655 - 4160 - 5065 - 5570 - 6075 - 6575 - 5580 - 7580 - 55
––––
65 - 5070 - 5575 - 6080 - 6580 - 5085 - 7085 - 5590 - 7595 - 80
–––––
80 - 6585 - 7090 - 7595 - 80
––
105 - 90110 - 95115 - 100
––––
41 - 3046 - 3250 - 3655 - 4160 - 46
–––––
55 - 3660 - 4665 - 5070 - 5575 - 6075 - 5080 - 7080 - 50
––––––
75 - 5580 - 60
85 - 65––
95 - 75––––––––
95 - 75–––––
––––
41 - 24––
55 - 3660 - 41
–––––
55 - 3260 - 3665 - 46
–––
80 - 65
–––––––
80 - 55–
85 - 60–––––––––––––––––
0.950.950.951.001.001.001.001.041.00
–1.681.681.721.771.811.861.861.911.95
–2.00
–2.043.683.683.683.683.583.583.63
–3.72
–3.993.994.224.226.176.176.226.266.406.586.62
–6.726.726.856.85
19
BA DC
CW2000W4000W8000W15000
WRP20WRP40WRP80WRP150
B
D
C
A E
°
B
C
D
1/4" - 18 NPTF
°
WTE20WTE40WTE80WTE150
W2000, W4000W8000, W15000
TSP100TSP200
A C DB
W2000W4000W8000W15000
BA
E
B
CA
W-Series Accessories
• Pro Series Swivel featuring Tilt and Swivel technology• 360 degree X-axis and 160 degree Y-axis rotation• 10,000 psi / 700 bar maximum working pressure• Increases tool fit in restricted access areas• Simplifies hose placement
• Extended reaction arm for W-series wrench• Full torque rated• Increases tool fit in restricted access areas
• Low profile reaction paddle• Lightweight interchangeable design• Provides greater flexibility in areas with restricted access
Model Number
Dimensions (in)
Model Number
Wrench Model
Weight(lbs)
Dimensions (in) Weight
(lbs)
Wrench Model
Model Number
Wrench Model
Dimensions (in)
TSP Series
WTE Series
WRP Series
Weight
(lbs)
To order a W-series wrench fitted with the TSP swivel, suffix the model number with "-P". e.g., W2000-P.
18.6020.7321.4824.26
1.502.002.503.00
2.192.583.354.00
2.522.64
.41.43
1 .061.06
.911.02
1.601.65
3.755.156.107.34
3.314.295.376.50
1.001.251.782.00
.821.834.308.69
2.503.314.085.93
.641.101.041.25
0.811.834.308.69
www.enerpac.com
�
20
22
28
�
• Very high torque-to-weight ratio• High speed, double-acting operation• High degree of rotation angle for increased productivity• Never-jam mechanism• High repeatability, with accuracy ± 3%• Slim nose radius and 360˚ swivel hose connection allow
easier positioning in confined areas• Few moving parts means durability and low maintenance• Push-button drive release; no tools needed to reverse
square or Allen drives for tightening or loosening• Storage case (included) protects from damage,
water and dirt• Lock-ring couplers are standard on all torque
wrenches, pumps and hoses
Lightweight Aluminum High-Power Wrench for Sockets or Allen Drives
� Easy and reliable service in the field using Enerpac SQD-series torque wrenches.
Swivel Hose Connection
All Enerpac torque wrenches feature a 360˚ swivel connection to allow easy access in all positions.
Twin 3.5:1 Safety Hoses
Use only Enerpac THC-700 series twin 3.5:1 safety hoses with SQD double-acting wrenches to ensure
the integrity of your system.
Optional Allen Drives
Expanded versatility with a wide range of metric and imperial Allen drives.
Page:
Page:
SQD-Series, Square Drive Wrenches
Shown: SQD-50-I
21
B
H
D NJ
C LK
G
EA
M
60
28
10
TORQUE WRENCH SELECTION (based on socket size range)
Double-Acting, Square Drive Wrenches
Torque WrenchModel No.
Square Drive
(in)
Max.Torque
@ 11,600 psi
Dimensions (in) Weight(incl.
reaction arm and
square drive)
(lbs)
SQDSeries
Maximum Torque:
19,875 Ft.lbs Square Drive Range:3⁄4-21⁄2 inchesMaximum Operating Pressure:
11,600 psi
Use only heavy-duty Impact Sockets for power driven torquing equipment, according to ISO 2725 and
ISO 1174; DIN 3129 and DIN 3121 or ASME-B107.2/1995.
Torque Wrench Pumps and Hoses
Enerpac system matched air and electric torque wrench pumps provide control to
operate hydraulic torque wrenches.
To
rque
Ran
ge
(x 1
000
Ft.
lbs)
�
Socket Size Range (inch) �
Hexagon Bolt and Nut Sizes
See the table for hexagon sizes of bolts, nuts and related thread diameters.
Page:
� All wrenches come standard with swivel coupler, square drive and reaction arm.
Page:
Page:
(Ft.lbs) (Nm)
6.578.058.899.9610.7113.45
2.833.624.214.535.286.46
2.092.672.953.313.944.69
.941.221.411.541.892.32
4.255.316.026.467.008.58
3.744.534.805.125.917.87
1.381.381.381.381.971.97
.24
.59
.47
.50
.44
.69
1.081.301.691.551.762.97
1.041.341.541.692.132.48
1.442.072.522.683.213.90
¾
1
1½
1½
1½
2½
5.529.35
11.9017.6426.5554.00
¾
1
1½
1½
1½
2½
1735355055707360
11,83519,875
SQD-25-ISQD-50-ISQD-75-ISQD-100-ISQD-160-ISQD-270-I
A B C D E G H K L M NJ
3/4 13/82
23/8 31/8 37/8 45/8 61/80
5
10
15
SQD-75-I
SQD-100-I
SQD-160-I
SQD-270-I20
SQD-25-I
SQD-50-I
235048007560
10,00016,00027,000
www.enerpac.com22
48
28
60
Model Number
Nut Cutters
Remove rusted or corroded nuts easily with Enerpac Nut Cutters. Hexagon nut capacities up to 2.88 in.
� SQD-100-I with RAH-100 Reaction Arm and Allen drive used for loosening hexagon socket head cap screws.
Model Number
(max. capacity)
TORQUE WRENCH OPTIONAL ALLEN DRIVES, IMPERIAL
REACTION ARM FOR ALLEN
DRIVE
MaximumTorque 1)
(Ft.lbs)
NoseRadius
D
(in)
HexagonSize
(in)
Model Number
� SELECTION CHART
1) Determine maximum torque according to the bolt size and grade.
ForSQDSeries
Maximum Torque at 11,600 psi:
19,875 Ft.lbs Allen Drive Range:1⁄2-21⁄4 inchesNose Radius:
0.94-2.32 inches
Torque Wrench Pumps and Hoses
Enerpac system matched air and electric torque wrench pumps provide control to
operate hydraulic torque wrenches.
Hexagon Bolt and Nut Sizes
See the table for hexagon sizes of bolts, nuts and related thread diameters.
Page:
Page:
SQD-25-I(1735 Ft.lbs)
SQD-50-I(3550 Ft.lbs)
SQD-100-I(7360 Ft.lbs)
SQD-160-I(11,835 Ft.lbs)
SQD-270-I(19,875 Ft.lbs)
SQD-75-I(5570 Ft.lbs)
SQD-Series, Imperial Allen Drives
Page:
25A-05025A-06325A-07525A-08825A-100
RAH-25
390735132517351735
0.94
½
⅝
¾
7�8
1
50A-06350A-07550A-08850A-10050A-11350A-125–
RAH-501.22
⅝
¾
7/8
1
1⅛
1¼
–
73513252065309535503550
–
100A-088100A-100100A-113100A-125100A-138100A-150
RAH-100
206530954350627073607360
1.54
7�8
1
1⅛
1¼
1⅜
1½
160A-125160A-138160A-150160A-163160A-175
RAH-160
62707745
10,32511,83511,835
1.89
1¼
1⅜
1½
1⅝
1¾
270A-150270A-163270A-175270A-188270A-200270A-225––
RAH-2702.32
1½
1⅝
1¾
17�8
2
2¼
––
10,32513,27516,22519,87519,87519,875
––
75A-06375A-07575A-08875A-10075A-11375A-125–
RAH-751.41
⅝
¾
7�8
1
11�8
11�4
–
73513252065309543505570
–
23
250%
50
Model Number
(max. capacity)
Model Number
TORQUE WRENCH OPTIONAL ALLEN DRIVES, METRIC
REACTION ARM FOR ALLEN
DRIVE
MaximumTorque
(Ft.lbs)
NoseRadius
D(in)
HexagonSize
(mm)
Model Number
ForSQDSeries
Maximum Torque at 11,600 psi:
19,875 Ft.lbs Allen Drive Range:
14-70 mmNose Radius:
0.94-2.32 inches
Flange Spreaders
Separates pipe flanges with ease, enabling efficient maintenance tasks.
Optional Allen Drives and Reaction Arm
The RAH-Reaction Arm for Allen drives must be used instead of reaction arm for square drives.
� SELECTION CHART
Page:
Select the Right Torque
Choose your Enerpac Torque Wrench using the loosening torque rule of thumb:
Loosening torque may require 250% of tightening torque depending on the condition of the fastener.
SQD-25-I(1735 Ft.lbs)
SQD-50-I(3550 Ft.lbs)
SQD-100-I(7360 Ft.lbs)
SQD-160-I(11,835 Ft.lbs)
SQD-270-I(19,875 Ft.lbs)
SQD-75-I(5570 Ft.lbs)
� SQD-50-I with 50A-22 Allen drive with RAH-50 Reaction Arm for Allen drives.
SQD-Series, Metric Allen Drives
25A-1425A-1725A-1925A-2225A-24
550955132517351735
0.94
1417192224
50A-1750A-1950A-2250A-2450A-2750A-3050A-32
1.22
17192224273032
955132520652580355035503550
100A-22100A-24100A-27100A-30100A-32100A-36
206525803685516062707360
1.54
222427303236
160A-30160A-32160A-36160A-41160A-46
516062708850
11,83511,835
1.89
3032364146
270A-36270A-41270A-46270A-50270A-55270A-60270A-65270A-70
2.32
3641465055606570
885013,27518,44019,87519,87519,87519,87519,875
RAH-751.41
17192224273032
955132520652580368551605570
75A-1775A-1975A-2275A-2475A-2775A-3075A-32
RAH-25
RAH-50
RAH-100
RAH-160
RAH-270
www.enerpac.com
�
24
250%
28
48
�
HXD-Series, Hexagon Cassette Wrenches
• High torque-to-weight ratio, slim nose radius and flat design• High speed, high degree of rotation angle• Snap in, interchangeable cassettes, no tools required• 360˚ swivel hose connection allows easier positioning in
confined areas• High repeatability, with accuracy ± 3%• Strong unibody design, integrated reaction arm and few
moving parts make wrenches durable and reliable• Extensive range of metric and imperial hexagon cassettes
and reducers• Drive unit and cassette come in storage case to protect from
damage, water and dirt• Lock-ring couplers are standard
Shown from left to right: HXD-60 with CC-680, HXD-30 with CC-360
Twin 3.5:1 Safety Hoses
Use only Enerpac THC-700 series twin 3.5:1 safety hoses with HXD double-acting wrenches to ensure the integrity of your system.
Nut Cutters
Remove rusted or corroded nuts easily with Enerpac Nut Cutters. Hexagon nut capacities up to 2.88 in.
Aluminum, Low Profile
� The HXD-30 drive unit combined with cassette CC-3238 is the best solution for this turbine application. The slim nose radius and swivel couplers allow easy access in all positions.
� An Enerpac HXD hydraulic wrench brings safety and efficiency to this flange maintenance job at a refinery.
Select the Right Torque
Choose your Enerpac Torque Wrench using the loosening torque rule of thumb:
Loosening torque may require 250% of tightening torque depending on the condition of the fastener.
Page:
Page:
25
CAF
E
B
D
H
�
21
28
12
60
26
Drive Unit *Model Number
Double-Acting Hydraulic Torque Wrenches
HXDSeries
Maximum Torque:
17,860 Ft.lbs
Nose Radius:
1.12-3.78 inches
Hexagon Range:
11⁄4-5 inches
Maximum Operating Pressure:
11,600 psi
Torque Wrench Pumps
System matched air and electric pumps provide control to operate Enerpac HXD Torque Wrenches.
Page:
Page:
DRIVE UNIT AND INTERCHANGEABLE CASSETTE SELECTION
� QUICK SELECTION CHART
Drive Unit with Cassette
Cassette Range
Metric and Imperial Sizes
Expanded versatility with the full range of metric and imperial Reducer Inserts and Holding Rings.
Page:
C(mm)(in) E FB HA D
Drive Unit and Cassette Dimensions
(in)
* With integrated reaction arm.
Weight(including smallest cassette)
(lbs)
MaximumTorque
at 11,600 psi
(Ft.lbs)
Shown from left to right: CC-3238, HXD-30
Torque Wrench Selection in 2 steps:
1. Drive UnitSelect the HXD-drive Unit using the quick selection chart below.
2. CassetteSelect the appropriate CC-cassette from pages 26 and 27.
To
rque
Ran
ge
(Ft.
lbs)
�
Hexagon Size Range (inch) �
Hexagon Bolt and Nut Sizes
See the table for hexagon sizes of bolts, nuts and related thread diameters.
Page:
1.101.381.852.20
1.571.972.563.22
3.58 - 4.064.53 - 5.125.55 - 6.146.80 - 7.95
1.501.501.502.00
5.316.147.8710.20
1.12 - 1.871.36 - 2.381.83 - 2.892.44 - 3.78
4.68.1
16.328.9
2.362.953.784.92
24254565922017860
HXD-30HXD-60HXD-120HXD-240
32 - 6041 - 8055 - 10080 - 130
1¼ - 2⅜
1⅝ - 3⅛
23⁄16 - 37�8
3⅛ - 5
0
HXD-30
HXD-60
HXD-120
HXD-240
9800
11/4 13/4 23/16 29/16 25/16 33/8 33/4 41/8 41/2 5
1400
2800
4200
5600
7000
8400
2600
1200
4000
6800
5400
8200
26
CCINHRSeries
Maximum Torque at 11,600 psi:
17,860 Ft.lbsHexagon Range:
1.25-5 inches
Model Number
(max. capacity)
Model Number
DRIVE UNIT
� SELECTION CHART
INTERCHANGEABLE CASSETTE, IMPERIAL
Max.Torque
(Ft.lbs)
Hex.Size 1)
(in)
Nose Radius
D
(in)
Weight
(lbs)
HexagonSize
(in)
Model Number
HOLDINGRINGS
OPTIONAL ADD-ON REDUCER INSERTS, IMPERIAL
Model Number
HexagonSize
(in)
Model Number
Other Reducer Insert dimensions available upon request.1) See the table of hexagon bolt and nut sizes and related thread diameters on page 60.2) Additional imperial Reducer Insert: 31�8"–29/16" IN24313-256 fits CC-24313 Cassette. Use HR-80 Holding Ring.3) Additional imperial Reducer Insert: 33�4"–29/16" IN24375-313 fits CC-24388 Cassette. Use HR-100 Holding Ring.
� The optional Reducer Insert must be secured in the Cassette with a Holding Ring.
HXD-60(4565 Ft.lbs)
HXD-30(2425 Ft.lbs)
HXD-120(9220 Ft.lbs)
HXD-240(17860 Ft.lbs)
HXD-Series, Imperial Cassettes and Inserts
CC-6163CC-6181CC-6200CC-6219CC-6238CC-6256CC-6275CC-6293CC-6313
28303540
3990
4565
1.361.561.711.831.912.072.192.262.38
2.62.93.23.33.44.14.24.34.4
CC-3125CC-3144CC-3163CC-3181CC-3200CC-3219CC-3238
1250154518402130
2425
1.121.241.361.521.651.771.87
1.21.41.51.82.12.22.3
–HR-36HR-41HR-46HR-50HR-55HR-60
–IN3144-125IN3163-144IN3181-163IN3200-181IN3219-200IN3238-219
––IN3163-125IN3181-144IN3200-163IN3219-181IN3238-200
5900
7225
8010
9220
1.831.912.072.192.262.262.382.542.662.782.89
5.85.86.16.26.36.36.57.88.08.28.3
CC-12219CC-12238CC-12256CC-12275CC-12293CC-12300CC-12313CC-12338CC-12350CC-12375CC-12388
HR-55HR-60HR-65HR-70HR-75HR-75HR-80HR-85HR-90HR-95HR-100
IN12219-200IN12238-219IN12256-238IN12275-256IN12293-275IN12300-275IN12313-293IN12338-300IN12350-313IN12375-350IN12388-350
IN12219-181IN12238-200IN12256-219IN12275-238IN12293-256IN12300-256IN12313-275IN12338-293IN12350-300IN12375-338IN12388-338
–HR-46HR-50HR-55HR-60HR-65HR-70HR-75HR-80
–IN6181-163IN6200-181IN6219-200IN6238-219IN6256-238IN6275-256IN6293-275IN6313-293
––IN6200-163IN6219-181IN6238-200IN6256-219IN6275-238IN6293-256IN6313-275
CC-243132)
CC-24338CC-24350CC-24375CC-243883)
CC-24413CC-24425CC-24463CC-24500
103251168512225127751331515490
17860
2.442.602.712.832.993.153.303.543.78
11.211.411.411.912.312.514.916.016.3
HR-80HR-85HR-90HR-95HR-100HR-105HR-110HR-120HR-130
IN24313-293IN24338-313IN24350-313IN24375-350IN24413-388IN24425-388IN24463-425IN24500-463
IN24313-275IN24338-300IN24350-300IN24375-338IN24388-338IN24413-375IN24425-375IN24463-413IN24500-425
1⅝
113�16
2
23�16
2⅜
29�16
2¾
215�16
3⅛
–113�16 – 1⅝
2 – 113�16
23�16 – 2
2⅜ – 23�16
29/16 – 2⅜
2¾ – 29/16
215�16 – 2¾
3⅛ – 215�16
1¼
17�16
1⅝
113�16
2
23�16
2⅜
–17�16 – 1¼
1⅝ – 17�16
113�16 – 1⅝
2 – 113�16
23�16 – 2
2⅜ – 23�16
––
1⅝ – 1¼
113�16 – 17�16
2 – 1⅝
23�16 – 113�16
2⅜ – 2
23�16
2⅜
29�16
2¾
215�16
3
3⅛
3⅜
3½
3¾
37�8
23�16 – 2
2⅜ – 23�16
29�16 – 2⅜
2¾ – 29�16
215�16 – 2¾
3 – 2¾
3⅛ – 215�16
3⅜ – 3
3½ – 3⅛
3¾ – 3½
37�8 – 3½
23�16 – 113�16
2⅜ – 2
29�16 – 23�16
2¾ – 2⅜
2115�16 – 29�16
3 – 29�16
31�8 – 23�4
33�8 – 215�16
3½ – 3
3¾ – 3⅜
37�8 – 3⅜
––
2 – 1⅝
23�16 – 113�16
2⅜ – 2
29�16 – 23�16
2¾ – 2⅜
215�16 – 29�16
3⅛ – 2¾
3⅛
3⅜
3½
3¾
37�8
4⅛
4¼
4⅝
5
3⅛ – 215�16
3⅜ – 3⅛
3½ – 3⅛
3¾ – 3½
4⅛ – 37�8
4¼ – 37�8
4⅝ – 4¼
5 – 4⅝
3⅛ – 2¾
3⅜ – 3
3½ – 3
3¾ – 3⅜
37�8 – 3⅜
4⅛ – 3¾
4¼ – 3¾
4⅝ – 4⅛
5 – 4¼
27
CCINHRSeries
Maximum Torque at 11,600 psi:
17,860 Ft.lbsHexagon Range:
30-130 mm
Model Number
(max. capacity)
Model Number
DRIVE UNIT
� SELECTION CHART
INTERCHANGEABLE CASSETTES, METRIC
Max.Torque
(Ft.lbs)
Hex.Size 1)
(mm)
Nose Radius
D(in)
Weight
(lbs)
HexagonSize
(mm)
Model Number
HOLDINGRINGS
OPTIONAL ADD-ON REDUCER INSERTS, METRIC
Model Number
HexagonSize
(mm)
Model Number
HexagonSize
(mm)
Model Number
� The optional Reducer Insert must be secured in the Cassette with a Holding Ring.
Other Reducer Insert dimensions available upon request.1) See the table of hexagon bolt and nut sizes and related thread diameters on page 60.
HXD-120(9220 Ft.lbs)
HXD-60(4565 Ft.lbs)
HXD-30(2425 Ft.lbs)
HXD-240(17860 Ft.lbs)
HXD-Series, Metric Cassettes and Inserts
CC-1255CC-1260CC-1265CC-1270CC-1275–CC-1280CC-1285CC-1290CC-1295CC-12100
5900
7225
8010
9220
5560657075–
80859095100
1.831.912.072.192.26
–2.382.542.662.782.89
5.85.86.16.26.3–
6.57.88.08.28.3
HR-55HR-60HR-65HR-70HR-75–HR-80HR-85HR-90HR-95HR-100
IN12-5541IN12-6046IN12-6550IN12-7055IN12-7560–IN12-8065IN12-8570IN12-9075IN12-9580IN12-10085
IN12-5546IN12-6050IN12-6555IN12-7060IN12-7565–IN12-8070IN12-8575IN12-9080IN12-9585IN12-10090
IN12-5550IN12-6055IN12-6560IN12-7065IN12-7570–IN12-8075IN12-8580IN12-9085IN12-9590IN12-10095
55/5060/5565/6070/6575/70
–80/7585/8090/8595/90
100/95
55/4660/5065/5570/6075/65
–80/7085/7590/8095/85
100/90
55/4160/4665/5070/5575/60
–80/6585/7090/7595/80
100/85
CC-641CC-646CC-650CC-655CC-660CC-665CC-670CC-675CC-680
28303540
3990
4565
414650556065707580
1.361.561.711.831.912.072.192.262.38
2.62.93.23.33.44.14.24.34.4
HR-41–HR-50HR-55HR-60HR-65HR-70HR-75HR-80
––IN6-5036IN6-5541IN6-6046IN6-6550IN6-7055IN6-7560IN6-8065
IN6-4136–IN6-5046IN6-5550IN6-6055IN6-6560IN6-7065IN6-7570IN6-8075
41/36–
50/4655/5060/5565/6070/6575/7080/75
––IN6-5041IN6-5546IN6-6050IN6-6555IN6-7060IN6-7565IN6-8070
––
50/4155/4660/5065/5570/6075/6580/70
––
50/3655/4160/4665/5070/5575/6080/65
CC-332CC-336CC-341CC-346CC-350CC-355CC-360
1250154518402130
2425
32364146505560
1.121.241.361.521.651.771.87
1.21.41.51.82.12.22.3
––HR-41HR-46HR-50HR-55HR-60
––IN3-4136IN3-4641IN3-5046IN3-5550IN3-6055
––
41/3646/4150/4655/5060/55
––IN3-4132IN3-4636IN3-5041IN3-5546IN3-6050
––
41/3246/3650/4155/4660/50
––IN3-4130IN3-4632IN3-5036IN3-5541IN3-6046
––
41/3046/3250/3655/4160/46
CC-2480CC-2485CC-2490CC-2495CC-24100CC-24105CC-24110CC-24115CC-24120CC-24125CC-24130
102451182012215126101340015370
17860
80859095100105110115120125130
2.442.602.722.832.993.153.313.433.543.663.78
11.211.411.411.912.312.512.815.616.116.116.3
HR-80HR-85HR-90HR-95HR-100HR-105HR-110HR-115HR-120HR-125HR-130
IN24-8065IN24-8570IN24-9075IN24-9580IN24-10085IN24-10590IN24-11095IN24-115100IN24-120105IN24-125110IN24-130115
IN24-8075IN24-8580IN24-9085IN24-9590IN24-10095IN24-105100IN24-110105IN24-115110IN24-120115IN24-125120IN24-130125
80/7585/8090/8595/90
100/95105/100110/105115/110120/115125/120130/125
IN24-8070IN24-8575IN24-9080IN24-9585IN24-10090IN24-10595IN24-110100IN24-115105IN24-120110IN24-125115IN24-130120
80/7085/7590/8095/85100/90105/95110/100115/105120/110125/115130/120
80/6585/7090/7595/80100/85105/90110/95115/100120/105125/110130/115
28 www.enerpac.com
29 34
6
12
30 36
20
24
Selection Matrix
PMU-Series
ELECTRIC PUMPS
10,000 psiTorqueWrenches Model No.
Page:
ZU4-Series
Page:
AIR DRIVEN PUMPS
PTA-Series
Page: Page:
TWINHOSES
THQ-SeriesTHC-Series
Optimum Torque Wrench and Pump Combinations
For optimum speed and performance Enerpac recommends the following system set-up with wrench-pump-hose combinations.
IMPORTANT!
Always make sure that the torque scale on the pump matches the torque wrench size for accurate torque settings.
ZA4T-Series
Flow at rated
pressure:20 in3/min115V, 1 ph
Flow at rated
pressure:20 in3/min230V, 1 ph
Flow at rated
pressure:60 in3/min115V, 1 ph
Flow at rated
pressure:60 in3/min230V, 1 ph
Flow at rated
pressure:20 in3/min
Flow at rated
pressure:60 in3/min
Call Enerpac!
For other combinations, consult your Enerpac bolting expert or your
authorized Enerpac distributor.
THQ-706T (19.5 ft)THQ-712T (39.0 ft)
11,600 psi Torque Wrenches Model No.
THC-7062 (19.5 ft)THC-7122 (30.0 ft)
Select the right torque
Choose your Enerpac torque wrench using the untightening rule of thumb:
• Be aware that when loosening a nut or bolt more torque is usually required than when tightening.
• Do not apply more than 75% of the maximum torque output of the tool when loosening nuts or bolts.
Conditions of bolted joints• For fully threaded UNC nuts and
bolts do not exceed 1½ times nominal torque for a friction coefficient of 0,1.
• Humidity corrosion (rust) requires up to 2 times the torque required for tightening.
• Sea water and chemical corrosion requires up to 2½ times the torque required for tightening.
• Heat corrosion requires up to 3 times the torque required for tightening.
Any ZU4-Series pump may be used.
Any ZU4-Series pump may be used.
Any ZA4T-Series pump may be used.
Any ZA4T-Series pump may be used.
PMU-10427-Q
PMU-10427-Q
–
PMU-10422-Q
PMU-10422-Q
–
S1500S3000S6000S11000S25000W2000W4000
W8000W15000
PTA-1404-Q
PTA-1404-Q
–
–
SQD-25-ISQD-50-ISQD-75-ISQD-100-ISQD-160-ISQD-270-IHXD-30HXD-60HXD-120HXD-240
PMU-10427
PMU-10427
–
–
PMU-10422
PMU-10422
–
–
PTA-1404
–
PTA-1404
–
– –
29
�
19.5 feet long, 2 hoses
39 feet long, 2 hoses
10,000 psi19.5 pies de longitud, 2 mangueras19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THC-7062THC-712239 pies de longitud, 2 manguerasTHC-7062THC-7122THQ-706TTHQ-712T
19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THC-7062THC-7122
19.5 pies de longitud, 2 mangueras
19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THQ-706TTHQ-712T
39 pies de longitud, 2 manguerasTHC-7062THC-7122
19.5 feet long, 2 hoses
39 feet long, 2 hoses
11,600 psi
10,000 psi
19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THQ-706TTHQ-712TTHC-7122
THQ-706TTHQ-712T
THC-7062
S1500 W2000 S3000 W4000
SQD-25-I HXD-30 SQD-50-I HXD-60
PMU-10427-Q
PMU-10447-Q
PMU-10422-Q
PMU-10442-Q
PMU-10427
PMU-10447
PMU-10422
PMU-10442
Portable Electric Torque Wrench Pumps
� PERFORMANCE CHART
• Powerful two-speed pump is lightweight and easy to carry• Standard heat exchanger package keeps pump cool under
extreme use• Glycerin filled gauge with scales reading in psi and bar• Transparent overlays in Ft.lbs and Nm for all Enerpac
torque wrenches provide a quick torque reference• Universal motor for a high power-to-weight ratio;
generates full pressure on as little as 50% of the rated line voltage
• Adjustable pressure relief valve for accurate torque adjustments and precise repeatability
Shown: PMU-10427
Reservoir Capacity:
0.5-1 gal.Flow at 10,000 psi:
20 in3/min.
Maximum Operating Pressure:
10,000 and 11,600 psi
Motor Size:
0.5 hp
PMUSeries
Oil Flow Rate
(in3/min) 1st stage 2nd stage
Useable Oil
Capacity
(gal)
ModelNumber
Electric Motor
DimensionsL x W x H
(in)
Weight
(lbs)
Maximum Pressure Rating
(psi) 1st stage 2nd stage
115V- 1 ph -50/60Hz
115V- 1 ph -50/60Hz
230V- 1 ph -50/60Hz
230V- 1 ph -50/60Hz
115V- 1 ph -50/60Hz
115V- 1 ph -50/60Hz
230V- 1 ph -50/60Hz
230V- 1 ph -50/60Hz
For Use With Torque Wrenches
Twin Torque Wrench Hoses
Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps, or use
THC-700 series twin hoses with 11,600 psi pumps.
19.5 feet long, 2 hoses
39 feet long, 2 hoses
19.5 feet long, 2 hoses39 feet long, 2 hoses
11,600 psi
10,000 psi
Pump Ratings
-Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers.
-E suffix pumps are for use with Enerpac SQD and HXD 11,600 psi torque wrenches, and include polarized lock-ring safety couplers.
200
200
200
200
200
200
200
200
.50
1.0
.50
1.0
.50
1.0
.50
1.0
17 x 11 x 15
17 x 13 x 15
17 x 11 x 15
17 x 13 x 15
17 x 11 x 15
17 x 13 x 15
17 x 11 x 15
17 x 13 x 15
53
60
53
60
53
60
53
60
20
20
20
20
20
20
20
20
700
700
700
700
700
700
700
700
10,000
10,000
10,000
10,000
11,600
11,600
11,600
11,600
30 www.enerpac.com
�
ZU4-Series Electric Torque Wrench Pumps
� Any brand of hydraulic torque wrench can be powered by the portable ZU4-Series torque wrench pump.
• Features Z-CLASS high-efficiency pump design; higher oil flow and bypass pressure, cooler running and requires 18% less current draw than comparable pumps
• Powerful 1.7 hp universal electric motor provides high power-to-weight ratio and excellent low-voltage operating characteristics
• High-strength, molded composite shroud protects motor and electrical components, while providing an ergonomic, non-conductive handle for easy transport
• Low-voltage pendant provides additional safety for the operator
• Valve technology reduces oil operating temperatures and withstands contaminants to increase pump reliability
• LCD readout provides pressure and torque display and a number of diagnostic and readout capabilities never before offered on a portable electric pump
• Auto cycle feature provides continuous cycle operation of the torque wrench as long as the advance button is pressed. (Pump can be used with or without auto cycle feature)
Shown: ZU4204TB-Q and ZU4204BB-Q
Classic Electrical
Basic electrical package includes mechanical contactor, ON/OFF toggle switch, pendant with electro-mechanical
pushbuttons, 24V transformer timer and operator accessible circuit breaker.
Back-lit LCD, for Pro-Series
• Pump usage information, hour and cycle counts
• Low-voltage warning and recording
• Self-test and diagnostic capabilities
• Information can be displayed in English, French, German, Italian, Spanish and Portuguese
• Pressure transducer is more accurate and durable than analog gauges
FIRMWARE 7.0, for Pro-Series
• Display torque in Ft.lb. or Nm• Display pressure in bar, MPa
or psi• Torque wrench model is selectable• “Auto cycle” setting easily
programmable
31
115V
230V
ZU4204TB-QZU4208TB-QZU4204TE-Q 2)
ZU4208TE-Q2)
ZU4204TI-Q3)
ZU4208TI-Q3)
ZU4204BB-QHZU4204BB-QZU4208BE-QH2)
ZU4204BE-Q2)
ZU4208BI-QHZU4208BI-Q
28
32
ZU4 Torque Wrench Pumps
Cur
rent
(am
ps)
�
OIL FLOW AND CURRENT vs PRESSURE
Oil
Flo
w (
in3 /
min
) �
Pressure (psi) �
Reservoir Capacity:
1 and 1.75 gal.Flow at 10,000 psi:
60 in3/min.Motor Size:
1.7 hp
ZU4Series
Maximum Operating Pressure:
10,000 and 11,600 psi
Oil FlowCurrent
1) All models meet CE safety requirements and all TÜV requirements 2) European plug and CE EMC directive compliant3) With NEMA 6-15 plug4) Select -E suffixed pumps for Enerpac SQD and HXD 11,600 psi torque wrenches
Model Number 1) 4)
Usable Oil Capacity
(gal)
Weight with Oil
(lbs)
Motor Electrical Specification
Z-CLASS – A Pump For Every Application
Patented Z-CLASS pump technology provides high by-pass pressures for increased productivity—important in applications using long hose runs and high pressure-drop circuits, like heavy
lifting or certain double-acting tools.
Enerpac ZU4 Hydraulic Pumps are built to power small to large torque wrenches. Choosing the right ZU4 torque wrench pump for your application is easy.
Classic Electric Torque Wrench Pump• The Classic has an analog gauge and traditional electro-mechanical
components (transformers, relays and switches) in place of solid-state electronics. The Classic delivers durable, safe and effi cient hydraulic power.
Pro Series Electric Torque Wrench Pump• Digital (LCD) display features a built-in hour meter, pressure and torque
display, and shows self-diagnostic, cycle-count and low voltage warning information. These premium features are not available on any other pump—anywhere!
AutoCycle feature provides continuous cycle operation of the torque wrench as long as the advance button is pressed. (Pump can be used with or without AutoCycle feature).
� COMMON PUMP MODELS
For Use With Torque Wrenches
115 VAC, 1-ph115 VAC, 1-ph
208-240 VAC, 1-ph208-240 VAC, 1-ph208-240 VAC, 1-ph208-240 VAC, 1-ph
115 VAC, 1-ph115 VAC, 1-ph
208-240 VAC, 1-ph208-240 VAC, 1-ph208-240 VAC, 1-ph208-240 VAC, 1-ph
Pro
Ser
ies
Cla
ssic
All wrenches
All wrenches
Page:
Torque Wrench Pump Selection Matrix
For optimum speed and performance see the torque wrench pump and hose
selection matrix.
Pump Ratings
-Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers.
-E suffix pumps are for use with Enerpac SQD and HXD 11,600 psi torque wrenches, and include polarized lock-ring safety couplers.
Gauge Overlay Kit
Gauge overlay kits are also available separately. GT-4015 includes overlays for all SQD and HXD torque wrenches. GT-4015-Q
includes overlays for all S- and W-Series torque wrenches.
Page:
1.01.751.0
1.751.0
1.751.01.01.751.01.751.75
707670767076827383748879
0 2000 4000 6000 8000 10,0000
100
200
300
400
500
600
700 25
20
15
10
5
0
32 www.enerpac.com
Z 4 2 08 T E - Q H MU
28
19.5 feet long, 2 hoses
39 feet long, 2 hoses
10,000 psi19.5 pies de longitud, 2 mangueras19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THC-7062THC-712239 pies de longitud, 2 manguerasTHC-7062THC-7122THQ-706TTHQ-712T
19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THC-7062THC-7122
19.5 pies de longitud, 2 mangueras
19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THQ-706TTHQ-712T
39 pies de longitud, 2 manguerasTHC-7062THC-7122
19.5 feet long, 2 hoses
39 feet long, 2 hoses
11,600 psi
10,000 psi
19.5 pies de longitud, 2 mangueras39 pies de longitud, 2 mangueras
THQ-706TTHQ-712TTHC-7122
THQ-706TTHQ-712T
THC-7062
* 50/60 Hz** Pump type (-Q) shown, (-E) range is 1,800 - 11,600 psi.
Page:
8Options
ZU4 Ordering Matrix and Specifications
How to order your ZU4-Series torque wrench pump
Ordering Example 1
Model No. ZU4208TB-QMHK10,000 psi pump for use with Enerpac S- and W-Series and other 10,000 psi torque wrenches, 115V motor, 1.75 gallon reservoir, 4-wrench manifold, heat exchanger and skidbar.
Refer to the torque wrench pump selection matrix for optimum wrench, pump and hose combinations.
1Product
Type
2Motor Type
3Flow
Group
4Valve Type
5Reser voir
Size
6Valve
Operation
7Voltage
� This is how a ZU4 Series pump model number is built up:
1 Product Type
Z = Pump series
2 Motor Type
U = Universal electric motor
3 Flow Group
4 = 60 in3/min @ 10,000 psi
4 Valve Type
2 = Torque wrench valve
5 Reservoir Size (useable capacity)
04 = 1.0 gallon 08 = 1.75 gallons
6 Valve Operation
T = Solenoid valve with pendant, LCD Electric and pressure
transducer. B = Solenoid valve with pendant,
classic electrical
7 Voltage
B = 115V, 1 ph, 50/60 Hz E = 208-240V, 1 ph, 50/60 Hz (with
European plug CE RF compliant) I = 208-240V, 1 ph, 50/60 Hz (with
NEMA 6-15 plug)
8 Factory installed features and options
E = 11,600 coupler for use with HXD-,SQD-Series or other wrenches
Q = 10,000 coupler for use with S- and W-Series or other wrenches
H = Heat exchanger K = Skidbar M = 4-wrench manifold R = Roll cage
MotorSize
(hp)
*Motor ElectricalSpecification
Output Flow Rate
(in3/min)
Relief ValveAdjustment
Range
(psi)
SoundLevel
(dBA)100 psi
5,000 psi
700 psi
10,000 psi
ZU4 Performance
8Options
8Must be E or Q
▼ Most hydraulic torque wrenches can be powered by the Enerpac ZU4-Series torque wrench pump.
Twin Torque Wrench Hoses
Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps, or use THC-700
series twin hoses with 11,600 psi pumps.
115 VAC, 1-ph208-240 VAC, 1-ph
19.5 feet long, 2 hoses
39 feet long, 2 hoses
19.5 feet long, 2 hoses39 feet long, 2 hoses
11,600 psi
10,000 psi
Dimensions shown in inches
Reservoir Size(useable gallons)
� User adjustable relief valve� Heat exchanger (optional)� Skidbar (optional)� 4-wrench manifold (optional)� Roll cage (optional)
ZU4-Series Torque Wrench Pumps
A(in)
85-90535 761.7 1,800-10,000**700 60
11.75
6.08.1
9.00
19.4025.75
5.60 5.60
1.00 20.5
0
17.0
01.
19.5
0
16.29
25.0019.00
23.40
3.75
9.46A11.00
10.5012.50
4.63
1.63
2.75
5.76
33
SBZ-4L
ZTM-E
SBZ-4
ZHE-U4
ZRC-04ZRC-04H
ZTM-Q
Btu/h
ZU4 Torque Wrench Pump Options
Heat Exchanger• Removes heat from the bypass oil
to provide cooler operation
• Stabilizes oil viscosity, increasing oil life and reduces wear of pump and other hydraulic components
ThermalTransfer *
Max.Pressure
(psi)
Max.Oil Flow
(gpm)
Vol-tage
(VDC)
* At 5 gpm at 70 °F ambient temperature.
Do not exceed maximum oil flow and pressure ratings. Heat exchanger is not suitable for water-glycol or high water-based fluids.
4-Wrench Manifold• For simultaneous operation of
multiple torque wrenches
• Can be factory installed or ordered separately
Skidbar • Provides greater pump stability
on soft or uneven surfaces
• Provides easy two-handed lift
Accessory Kit No. *
Can be used on ZU4-Seriestorque wrench pumps
* Add suffix M to pump model number for factory installation.
Ordering Example: Model No. ZU4208TB-QM
for 11,600 psi torque wrenches
Accessory Kit No. *
Can be used on ZU4-Series torque wrench pumps
* Add suffix K to pump model number for factory installation.
1) Without heat exchanger 4.9 lbs.2) With heat exchanger 7.0 lbs.
Ordering Example: Model No. ZU4208TB-QK
1 and 1.75 gallon1)
ZU4 Series
Reservoir Capacity:
1 and 1.75 gal.Flow at 10,000 psi:60 in3/min.Motor Size:
1.7 hpMaximum Operating Pressure:
10,000 and 11,600 psi
Accessory Kit No. *
Can be used on ZU4-Series torque wrench pumps
* Add suffix H to pump model number for factory installation.
Heat Exchanger adds 9.1 lbs. to pump weight.
Ordering Example: Model No. ZU4208TE-H
1 and 1.75 gallon reservoir 1 and 1.75 gallon2)
Roll Cage • Protects pump
• Provides greater pump stability
Accessory Kit No. *
Can be used on ZU4-Series torque wrench pumps
1 and 1.75 gallon reservoir1)
1 and 1.75 gallon reservoir2)
* Add suffix R for factory installation.1) Without heat exchanger2) With heat exchangerOrdering Example: Model No. ZU4208BB-QR
for 10,000 psi torque wrenches
900 300 7.0 12
34 www.enerpac.com
�
Compact Pneumatic Torque Wrench Pump
Shown: PTA-1404
• Compact and portable • Handle located directly over pump’s center of
gravity for greater ease in carrying• High bypass (1800 psi) for faster torque cycles• High power-to-weight ratio suits all Enerpac
torque wrenches• Glycerine filled pressure gauge with scales
reading in psi/bar• Transparent overlays in Ft.lbs and Nm for all Enerpac
torque wrenches provide a quick torque reference• Internal safety relief valve, factory preset • 15 ft. air pendant assembly enables easy
maneuvering at the job site• Fitted with polarized safety lock-ring couplers
Two-Stage Power in a Portable Design
Gauge Overlay Kit
Gauge overlay kits are also available separately. GT-4015 includes overlays for all SQD and HXD torque
wrenches. GT-4015-Q includes overlays for all S- and W-Series torque wrenches.
Twin Torque Wrench Hoses
Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps, or use THC-700 series twin hoses with 11,600 psi pumps.
19.5 feet long, 2 hoses
39 feet long, 2 hoses
THC-7062THC-7122
11,600 psi
19.5 feet long, 2 hoses
THQ-706TTHQ-712T
10,000 psi
39 feet long, 2 hoses
Pump Ratings
-Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers.
-E suffix pumps are for use with Enerpac SQD and HXD 11,600 psi torque wrenches, and include polarized lock-ring safety couplers.
35
28
FLOW CHARTO
il flo
w in
3 /m
in �
Pressure (psi) �
Compact Pneumatic Torque Wrench Pump
Reservoir Capacity:
1 gal.Flow at 10,000 psi:
20 in3/min.Maximum Operating Pressure:
10,000 and 11,600 psi
PTASeries
Pump Flow Rates
(in3)
1st stage 2nd stage
Air Consumption
@ 100 psi
(scfm)
� PERFORMANCE CHART
ModelNumber
Reservoir Capacity
(gal)
Useable Oil
Capacity
(gal)
Air Pressure
Range
(psi)
Weight with Oil
(lbs)
Vent/Fill Plug
Hydraulic Ports1/4"-18 NPTF
Externally Adjustable
Relief Valve
Air Inlet3/8"-
18 NPTF
15' Air Control Pendant Assembly
Dimensions shown in inches.
Pressure Rating
(psi)
For Use With Torque Wrenches
Torque Wrench Pump Selection Matrix
For optimum speed and per-formance see the torque wrench pump and hose selection matrix.
Page:
1.0
1.0
PTA-1404-Q
PTA-1404
240
240
0.5
0.5
40
40
54
54
10,000
11,600
49-101
49-101
20
20
S1500 W2000 S3000 W4000
SQD-25-I HXD-30 SQD-50-I HXD-60
11.3
5
17.6
712
.09
5.88
2.64
1.28
6.82
10.1
0
6.33
19.52
11.24
10.91
.27
3.238.89
12.21
1.79
0 3000 6000 9000 120000
61
122
183
244
325
366
427
488
549
610
36 www.enerpac.com
�
ZA4T Air Driven Torque Wrench Pumps
• Features Z-CLASS high-efficiency pump design; higher oil flow and bypass pressure
• Two-speed operation and high by-pass pressure reduces cycle time for improved productivity
• Heat exchanger warms exhaust air to prevent freezing and cools the oil
• Ergonomic pendant allows remote operation up to 20 feet• Glycerin filled pressure gauge with transparent overlays
in Ft.lbs and Nm for Enerpac torque wrenches provide a quick torque reference
• Regulator-Filter-Lubricator with removeable bowls and auto drain is standard
Shown: ZA4204TX-ER
Pump Ratings
-Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers.
-E suffix pumps are for use with Enerpac SQD and HXD 11,600 psi torque wrenches, and include polarized lock-ring safety couplers.
� Most hydraulic torque wrenches can be powered by the Enerpac ZA4T-Series torque wrench pump.
Twin Torque Wrench Hoses
Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps, or use THC-700 series twin hoses with 11,600 psi pumps.
19.5 feet long, 2 hoses
39 feet long, 2 hoses
THC-7062THC-7122
11,600 psi19.5 feet long, 2 hoses
THQ-706TTHQ-712T
10,000 psi
39 feet long, 2 hoses
37
28
II 2 GD ck T4
39
KEMA 0602
� COMMON PUMP MODELS
Page:
ZA4T Specifications
ZA4T Series
Reservoir Capacity:
1 and 1.75 gal.Flow at 10,000 psi:
60 in3/min.Maximum Operating Pressure:
10,000 and 11,600 psi
Torque Wrench Pump Selection Matrix
For optimum speed and performance see the torque wrench, pump and hose selection matrix.
ZA4T-Series Pump Applications
The ZA4T-Series pump is best suited to power medium to large size torque wrenches.
Patent-pending Z-CLASS technology provides high by-pass pressures for increased productivity. Its high power to
weight ratio and compact design make it ideal for applications which require easy transport of the pump.
For further application assistance contact your local Enerpac office.
Accessory OptionsAvailable by placing the following additional suffix at the end of the model number:
K = SkidbarM = 4-wrench manifoldR = Roll cage
ATEX Certified
The ZA-series pumps are tested and certified according to the Equipment Directive 94 / 9 / EC “ATEX Directive”. The explosion protection is for equipment group II, equipment category 2 (hazardous area zone 1), in gas and/or dust atmospheres. The ZA-series pumps are marked with: Ex II 2 GD ck T4.
Model Number 1)
MaximumOperatingPressure
(psi)
Usable Oil Capacity
(gal)
Weight with Oil
(lbs)
For Use With Torque Wrenches
1) All models meet CE safety requirements and all CSA requirements.
Oil
Flo
w (i
n3 /m
in)
�
Pressure (psi) �
100 psi dynamic air pressure at 70 scfm
Flow Chart
Page:
1.01.751.01.01.751.0
ZA4204TX-QZA4208TX-QZA4204TX-QRZA4204TX-EZA4208TX-EZA4204TX-ER
10,00010,00010,00011,60011,60011,600
SQD-75-I SQD-100-I SQD-160-I SQD-270-I
HXD-120 HXD-240
S1500S3000S6000S11000S25000
W2000 W4000 W8000 W15000
9410010194
100101
600
500
400
300
200
100
38 www.enerpac.com
Z 4 2 08 T X - Q M RA
* Pump type (-Q) shown.
Air Consumption
(scfm)
Dynamic Air
Pressure Range
(psi)
Relief ValveAdjustment
Range
(psi)
Sound Level at 100 psi Dynamic
(dBA)
ZA4T Performance
1Product
Type
2Motor Type
3Flow
Group
4Valve Type
5Reser voir
Size
6Valve
Operation
7Voltage
� This is how a ZA4T-Series pump model number is built up:
1 Product Type
Z = Pump Series
2 Motor Type
A = Air motor
3 Flow Group
4 = 60 in3/min @ 10,000 psi
4 Valve Type
2 = Torque Wrench Valve 5 Reservoir Size (useable capacity)
04 = 1.0 gallon 08 = 1.75 gallons
8Options
6 Valve Operation
T = Air operated valve with pendant
7 Voltage
X = Not applicable
8 Factory installed features and options
E = 11,600 psi coupler for use with HXD- and SQD-Series wrenches
Q = 10,000 psi coupler for use with S- and W-Series or other wrenches
K = Skidbar M = 4-wrench manifold R = Roll cage
8Options
8Must be E or Q
How to order your ZA4T-Series torque wrench pump
Ordering Example 1
Model No. ZA4208TX-QMR
10,000 psi pump for use with Enerpac S- and W-Series and other 10,000 psi torque wrenches, 1.75 gallon reservoir, 4-wrench manifold, and roll cage.
Refer to the torque wrench pump selection matrix for optimum wrench, pump and hose combinations.
ZA4T Ordering Matrix and Specifications
Output Flow Rate(in3/min)
A
(in)
Dimensions shown in inches.
Reservoir Size
(useable gallons)
ZA4T-Series Torque Wrench Pumps
� User adjustable relief valve� Roll bar cage (optional)� Gauge with overlays� Filter/lubricator/regulator� Oil level sight gauge� Air input 1/2" NPTF� Standard handle Oil drain
100 psi
5,000 psi
700 psi
10,000 psi
80-9560-100600 1,400-10,000*20-100500 80 60
11.75
6.08.1
11,800 psi
55
.7711.00 .5
0
3.00
5.90
1.19
5.60
16.28 2.06
9.00
19.40
11.6
0
A9.46
1.00
20.5
0
.25
M8 X 123.75
12.50
39
ZTM-EZTM-Q
SBZ-4
ZRC-04
ZA4T Series
Reservoir Capacity:
1 and 1.75 gal.Flow at 10,000 psi:
60 in3/min.Maximum Operating Pressure:
10,000 and 11,600 psi4-Wrench Manifold• For simultaneous operation of
multiple torque wrenches
• Can be factory installed or ordered separately
Skidbar • Provides greater pump stability
on soft or uneven surfaces
• Provides two-handed lift
Accessory Kit No. *
Can be used on ZA4T-Seriestorque wrench pumps
* Add suffix M for factory installation.Ordering Example: Model No. ZA4208TX-QM
for 11,600 psi torque wrenches
Accessory Kit No. *
Can be used on ZA4T-Series torque wrench pumps
* Add suffix K for factory installation. Skidbar weight 4.9 lbs.Ordering Example: Model No. ZA4208TX-QK
1 and 1.75 gallon reservoir
ZA4T Torque Wrench Pump Options
Gauge Overlay Kit
Gauge overlay kits are also available separately. GT-4015 includes overlays for all SQD and HXD torque
wrenches. GT-4015-Q includes overlays for all S- and W-Series torque wrenches.
Roll Cage • Protects pump
• Provides greater pump stability
* Add suffix R for factory installation. Roll bar cage weight 7.5 lbs.Ordering Example: Model No. ZA4208TX-QR
Accessory Kit No. *
Can be used on ZA4T-Series torque wrench pumps
1 and 1.75 gallon reservoir
for 10,000 psi torque wrenches
Twin Torque Wrench Hoses
Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps, or use THC-700 series twin hoses with 11,600 psi pumps.
19.5 feet long, 2 hoses
39 feet long, 2 hoses
THC-7062THC-7122
11,600 psi19.5 feet long, 2 hoses
THQ-706TTHQ-712T
10,000 psi
39 feet long, 2 hoses
40 www.enerpac.com
�
N
C
80˚
D
A B
E
GT1-LCBGT2-LCBGT3-LCBGT4-LCBGT5-LCBGT6-LCB
42
• Six load cells from ⅝" to 3¾" or from M16 to M95• Twin ports for quick connection of multiple tools• Only one size of bridge per size of load cell• Detachable and rotational bridge simplifi es
tool positioning• Full bridge window• Piston stroke indicator• Black surface treatment protects against corrosion• Anti-slip grip for more secure handling• Universal and multi-use tool
GT-Series Hydraulic Bolt Tensioners
Range
(in) (mm)
Load Celland BridgeReference
Technical DataCylinder Effective
Area (in2)
Dimensions (in)
A
Stroke
(in)
Load Capacity
(ton) B C D
Shown: GT-Series bolt tensioners
Nearest obstruction.
Minimum stud protrusion
= 1x nut height minimum
Pumps and accessories
High pressure pumps, hoses and fi ttings matched for use with the Enerpac GT Bolt Tensioning system.
Accurate & Reliable
Extreme PerformanceBolt Tensioner
▼ GT2 Bolt Tensioner on a flange joint.
Page:
Weight
(lbs)
5.315.356.307.097.958.62
⅝"-1"1⅛"-1½"1½"-2"2"-2½"
2½"-3¼"3¼"- 3¾"
M16-M30M30-M39M39-M52M52-M68M68-M80M80-M95
2.324.157.95
15.1623.3729.41
25.245.186.4
164.9254.1319.8
0.390.390.390.390.390.39
4.454.374.965.556.186.81
1.061.381.812.443.073.23
3.394.215.436.858.279.45
6.609.02
15.4026.8441.1461.16
41
GT1-LCB
GT2-LCB
GT3-LCB
GT4-LCB
GT5-LCB
GT6-LCB
GT1PM-NRS01620 GT1PM-NRS01825 GT1PM-NRS02025 GT1PM-NRS02430 GT1PM-NRS02730 GT1PM-NRS03035 GT1P-NRS0625U11 GT1P-NRS0750U10 GT1P-NRS0875U09 GT1P-NRS1000U08 GT1P-NRS1125U08 GT2PM-NRS03035 GT2PM-NRS03335 GT2PM-NRS03640 GT2PM-NRS03940 GT2P-NRS1125U08 GT2P-NRS1250U08 GT2P-NRS1375U08 GT2P-NRS1500U08 GT3PM-NRS03940 GT3PM-NRS04245 GT3PM-NRS04545 GT3PM-NRS04850 GT3PM-NRS05250 GT3P-NRS1500U08 GT3P-NRS1625U08 GT3P-NRS1750U08 GT3P-NRS1875U08 GT3P-NRS2000U08 GT4PM-NRS05250 GT4PM-NRS05655 GT4PM-NRS06055 GT4PM-NRS06460 GT4PM-NRS06860 GT4P-NRS2000U08 GT4P-NRS2250U08 GT4P-NRS2500U08 GT5PM-NRS06860 GT5PM-NRS07260 GT5PM-NRS07660 GT5PM-NRS08060 GT5P-NRS2500U08 GT5P-NRS2750U08 GT5P-NRS3000U08 GT5P-NRS3250U08 GT6PM-NRS08060 GT6PM-NRS08560 GT6PM-NRS09060 GT6PM-NRS09560 GT6P-NRS3250U08 GT6P-NRS3500U08 GT6P-NRS3750U08 www.enerpac.com
GT-Series Hydraulic Bolt Tensioners
GTSeries
Bolt Range:
⅝"-3¾" | M16-M95Load:
0-319.8 tonsMaximum Operating Pressure
21,750 psi
How to Order
To provide maximum fl exibility Load Cell and Bridges are ordered separately from
Adaptor Kits.
Example, to order a complete tensioner for a 1" threaded bolt order:
1 x Load Cell and Bridge: GT1-LCB
1 x Adaptor Kit: GT1P-NRS1000U08
Load Celland BridgeReference
ThreadSize
Adaptor KitModel Number
PitchBetween
BoltsN (in)
MinimumHeight
E (in)
Bolting Integrity Software
A comprehensive on-line software solution for Bolted Joint integrity.
Integral databases hold data for:
• BS1560, MSS SP44, API 6A and 17D fl anged joints
• Common gasket materials and confi gurations
• Comprehensive range of bolt materials
• Comprehensive range of lubricants
• Enerpac's Controlled Bolting Equipment including: Torque Multipliers, Hydraulic Wrenches and Bolt Tensioning tools
Custom Joint information can also be entered.
The software offers Tool selection, Bolt Load calculations and Tool pressure settings, as well as, a combined Application data sheet and Joint completion report.
Weight
(lbs)
(224 kN)
(401 kN)
(769 kN)
(1467 kN)
(2261 kN)
(2845 kN)
2.172.202.242.322.442.562.172.202.322.442.562.802.913.033.152.802.913.033.153.623.783.904.134.253.623.783.904.134.254.654.764.885.005.124.654.765.005.715.875.986.385.675.875.986.386.656.657.017.136.657.017.13
6.656.506.506.466.576.696.656.506.466.576.696.816.856.977.096.816.856.977.098.358.468.588.508.668.358.468.588.508.669.459.619.769.92
10.089.459.619.92
10.9411.1011.2611.5410.7911.1011.2611.5412.2812.2812.4812.6812.2812.4812.68
3.483.323.152.882.552.223.453.172.862.682.315.685.214.774.255.815.324.844.29
12.5011.7710.9610.259.20
12.5611.7010.8910.109.17
23.6322.2220.7719.3217.8023.6321.2318.6338.0236.0634.0332.0139.1635.8432.4528.8649.0246.2042.5739.6945.5641.4336.94
M16 x 2M18 x 2.5M20 x 2.5M24 x 3M27 x 3
M30 x 3.55/8" 11UN
¾" 10UN
7/8" 9UN
1" 8UN
11/8" 8UN
M30 x 3.5M33 x 3.5M36 x 4M39 x 411/8" 8UN
1¼" 8UN
13/8" 8UN
1½" 8UN
M39 x 4M42 x 4.5M45 x 4.5M48 x 5M52 x 51½" 8UN
15/8" 8UN
1¾" 8UN
17/8" 8UN
2" 8UN
M52 x 5M56 x 5.5M60 x 5.5M64 x 6M68 x 62" 8UN
2¼" 8UN
2½" 8UN
M68 x 6M72 x 6M76 x 6M80 x 62½" 8UN
2¾" 8UN
3" 8UN
3¼" 8UN
M80 x 6M85 x 6M90 x 6M95 x 63¼" 8UN
3½" 8UN
3¾" 8UN
42 www.enerpac.com
�
43
ATP-Series Air Pump
Shown: ATP-1500
Flo
w (i
n3 /m
in) �
Flow (in3/min) at 90 psi air input
Pressure (psi) �
FLOW CHART
ATPSeries
Air Pressure
Range
(psi)
Pressure Rating
(psi)
Output Flow Rate at
0 psi
(in3/min)
ModelNumber
UseableOil
Capacity
(gal)
PumpType
High pressure
Reservoir Capacity:
1 gallonFlow at Rated Pressure:
4 in3/min. Maximum Operating Pressure:
21,750 psi
Air Consumption
(sfcm)
Sound Level
(dBA)
Weight
(lbs)
Output Flow Rate at
21,750 psi
(in3/min)
� HPT Shut-off Valve� HPT Out Port
� Filter/Regulator� Air On/Off Valve
• General purpose, high pressure air driven pump unit for products requiring up to 21,750 psi hydraulic pressure
• Compact, lightweight, rugged steel frame for protection and easy handling
• Prelubricated pump element, does not require an airline lubricator
• Easily adjustable output pressure control• Integrated and protected easy to read glycerin fi lled gauge• Safety relief valve limits output pressure
These products operate at ultra-high pressure, use only the specified fittings and hoses designed for these pressures.
Page:
ATP-1500 21,755 80-901.0 70 70 7026 4
0
5
10
15
20
25
30
500 1000 1500 2000 25000
15.0015.75
15.3
0
43
�
40
50°
HPT Pump and Accessories
High Pressure Hand Pump with Gauge
DescriptionModelNumber
Pressure Rating (psi)
Oil Displacement per Stroke
(in3)
UsableOil
Capacity
(in3)
HPT-1500
HPTSeries
Reservoir Capacity:
155 in3
Flow at 10,000 psi:
.037-.99 in3/strokeMaximum Operating Pressure:
21,750 psi (1500 bar)
Shown: HPT-1500
ModelNumber
HT-1503
HT-1510
HT-1503HR*
HT-1510HR*
End 1 Length
(ft)
End 2 Description CompleteSet
MaleHalf
FemaleHalf
Quick Disconnect Coupler*
Quick Disconnect Coupler and Adaptor Kit*
Quick Disconnect Blanking Coupler Set*
1/4 BSPM 120º Cone1/4 BSPM 120º Cone
BH150
BH150
3.28
9.84
3.28
9.84
B150
BW150AW
B150B
BR150
—
—
BH150
—
—
� HOSES
• Lightweight and portable high-pressure hand pump• Two-speed operation displaces a larger volume of oil per
stroke, reducing cycle times for many testing applications• Includes a gauge and coupler for direct connection to
GT-Series bolting tools• Integrated relief valve set at 21,750 psi
1/4 BSPM 120º Cone1/4 BSPM 120º Cone
BR150
BR150
* Includes dust caps * Includes dust caps
Applications
The Enerpac HPT high-pressure Hand Pump is ideally suited for use with hydraulic bolt tensioning
tools and hydraulic nuts.
1st stage
1st
stage2nd
stage2nd
stage
� FITTINGS
These products operate at ultra-high pressure, use only the specified fittings and hoses designed for these pressures.
Page:
Weight
(lbs)
155 .99 0.037 200 21,750
1.24
8.341.61
1.75
9.00
2.80
.49 22.08.57
20.75.29
4.74
19
�1
44 www.enerpac.com
�
Single-Acting, Cylinder Pump Sets
Shown cylinder-pump set: SCR-1010H
RC-Series, Single-acting, General Purpose Cylinders: For maximum versatility.• Collar and plunger threads along with base mounting holes
enable easy fixturing for use on specialized positioning tools• Can be used in all positions• Heavy-duty return springs• Baked enamel finish for corrosion resistance• Multiple stroke lengths and tonnages to match many joint
positioning and assembly applications
RCH-Series, Single-acting, Hollow Cylinders: For pushing and pulling applications.• Hollow plunger design is ideal for both pull and push joint
assembly applications• Heavy-duty return springs• Nickel-plated, floating center tube on models over 20 tons
increase product life• Center-hole diameters match-up to many threaded rods and
strands for use in joint assembly applications
Nominal Set Capacity
(ton)
Collapsed Height
(in)
Stroke
(in)
CylinderModel No.
Portable Hydraulic Power to Ease Joint Assembly
Cylinder Selection
• Optimum match of individual components• Sets include 6 foot safety hose, calibrated gauge with
gauge adaptor• All hand pumps are two-speed for increased productivity
RC-102RC-106RC-1010RC-154RC-156RC-252RC-254RC-256RC-2514RC-506RCH-202RCH-302RCH-603RCH-1003–––––
10
15
25
50203060
100–––––
2.136.13
10.134.006.002.004.006.25
14.256.252.002.503.003.00
–––––
4.789.75
13.757.88
10.696.508.50
10.7518.7511.136.317.039.75
10.00–––––
�1��32
�2
�3
45
Single-Acting, Cylinder Pump Sets
Hand Pump
P-392
Hand Pump
P-80
XA-Series Air Pump
XA-11
HoseModel No.
GaugeModel No.
Gauge AdaptorModel No.
Pump selection Accessories Included
SELECTION EXAMPLE
Selected cylinder:
• RC-106, Single-acting cylinder with 6.13” stroke
Selected pump:
• P-392, Lightweight hand pump
Set model number:
• SCR-106H
Included:• HC-7206 hose• GF-10P gauge • GA-2 adaptor
SC Series
Capacity:
5-95 tonsStroke:
1.50-14.25 inchesMaximum Operating Pressure:
10,000 psi
SET SELECTION:
Select the cylinder
Select the pump
Find the set model number in the blue field of the matrix
SCR-102HSCR-106HSCR-1010HSCR-154HSCR-156HSCR-252HSCR-254HSCR-256H––SCH-202HSCH-302H–––––––
––––––––SCR-2514HSCR-506H––SCH-603HSCH-1003H
––––
SCR-102ASCR-106ASCR-1010ASCR-154ASCR-156ASCR-252ASCR-254ASCR-256ASCR-2514ASCR-506ASCH-202ASCH-302ASCH-603A
–––––
HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206HC-7206
––––
GF-10PGF-10PGF-10PGP-10SGP-10SGF-20PGF-20PGF-20PGF-20PGF-50P
GF-813PGF-813PGF-813PGP-10S
–––––
GA-2GA-2GA-2GA-2GA-2GA-2GA-2GA-2GA-2GA-2GA-3GA-3GA-3GA-2
–––––
46 www.enerpac.com
�
ESSSeries
Capacity per lifitng point:
9-910 tonsMaximum Stroke:
200 inchesAccuracy:
± .040 inchMaximum Operating Pressure:
10,000 psi
Synchronous Positioning Applications
The Synchronous Positioning system uses feedback
from multiple sensors to control the positioning of any large, heavy or complex structure, regardless of weight distribution. Synchronous positioning reduces the risk of bending, twisting, tilting or mis-alignment due to uneven weight distribution or load-shifts between the positional points.
A PLC controller monitors each position and optional load sensor located at each point. By varying the oil flow to each point, the system maintains a very accurate positional control. This control maintains structural integrity and can increase productivity and safety of the job, by eliminating manual intervention in the event of a load-shift or other problem.
ESS-Series Synchronous Positioning Systems
Typical layout for a 4 point synchronous positioning system
• Multiple points, 9 to 910 tons capacity per point• High accuracy (+/- .040 in.)• PLC-control, user friendly touch screen• Automatic data storage, reporting and
graphical presentation• Secure system with warning and stop features
System Options:• Precise load and force measurement up to 1%
of full scale• Digital sensors provide:
- load read-out by positional point and system total- two axis differential control to level structures
• Oil heater or heat exchanger for extreme conditions
� Positioning a 3500 ton dragline was successfully done with an Enerpac synchronous system. This operation provided for exact alignment of the bearing on the rail, prior to torque tightening of the slew ring bolts.
Precise Positioning System for Assembly and Separation of Large Structures
�
. ..
.
...
TW-22
ATM-1
ATM-5 ATM-3
47
• Rectifi es twist and rotational misalignment without additional stress in pipe lines
• For most commonly used ANSI, API, BS and DIN fl anges• No slings, hooks, or lifting gear. Extremely safe, high precision• ATM-1 supplied with three bushings for different bolt hole
sizes. Can be used in reversed position.• ATM-3 fi ts when fl ange joint is: – between 1.18 - 5.23 inches apart and – bolt hole size 0.95 inches or greater• ATM-5 fi ts when fl ange joint is: – between 3.75 - 9 inches apart and – bolt hole size 1.25 inches or greater• Can be installed and used in any position and any location• Stays stable in position under full load
ATMSeries
Bolt Hole Range:
11/16-2⅛ inches Flange Wall Thickness:
11/16-8 inches Maximum Force:
0.3-5 tons
Adjustable Reach-on ATM-3
The highly adjustable reach of the wing, the reversible lift hook and manual
torque wrench TW-22 (3/8" drive) allow precise alignment.
* At 10,000 psi maximum operating pressure. ATM-5 weight including hydraulic cylinder. Total set weight 62 lbs.
ATM-5 Including Hydraulics
Including 10,000 psi hydraulics: RC-53 single-acting cylinder, P-142 two-
speed hand pump and 6 ft. long safety hose (HC-7206C).
All dimensions shown in inches.
(mm)(in)
Model Number
MaximumLifting Force
(ton)
Bolt Hole Range
(mm)(in)
Flange Wall Thickness Weight
� The Enerpac ATM-3 used to align a large ANSI fl ange.
(lbs)
From left to right: ATM-3, ATM-1, ATM-5
Flange Alignment Tools
0.3 3.35.5
ATM-1ATM-3ATM-5 *
4.421.435.7
11/16 - 11/8
1 - 21/8
≥ 11/4
17 - 27,225 - 54≥ 31,5
11/16 - 213/16 - 41/2
31/8 - 8
17 - 5030 - 11580 - 203
18.72
1.77 ø .834.13
3.94
2.22
3.16
ø .95
ø 1.07ø.663
14.82
14.5018.72
5.85
1.17
5.66
1.76
8.97
13.2
6
.86Ø
4.17
4.02
2.99
1.26
10.6
312
.09
9.45
20.7125.98
12.2
05.
12
D
F
B
H
3/8"-18NPTF
A
C
J
48 www.enerpac.com
�
Hydraulic Nut Cutters
Shown from left to right: NC-3241, NC-1319, NC-1924
• Compact and ergono mic design, easy to use• Unique angled head allows flush access• Single-acting, spring return cylinder• Heavy-duty chisels can be reground• Applications include servicing trucks, piping industry, tank
cleaning, petrochemical, steel construction and mining
Bolt Range
(in)
Hexagon Nut Range
(in)
Capa city
(ton)
OilCapa city
(in3)
Weight
(lbs)
ModelNumber
Capacity:
5-90 tons
NC Series
Hexagon Nut Range:
0.5-2.88 inchesMaximum Operating Pressure:
10,000 psi
Ordering Notes: Maximum allowable hardness to split is HRc-44. Not to be used on square nuts.Larger sizes available upon request.
Dimensions (in)
Enerpac Nut Cutters
Nut Cutters include a spare chisel, a spare set screw and the wrench used to secure the chisel. A CR-400 coupler is standard.
ReplacementChiselModelNumber
Nut Cutter Sets
Hydraulic Nut Cutters are
available as sets (pump, tool and hose).
Splitter Model Number
Set Model Number
Pump Model Number
� Easily removing rusty nuts during railroad construction is just one of many application examples for the Enerpac Nut Cutters.
A B C D F H J
NC-1319NC-1924NC-2432NC-3241NC-4150NC-5060NC-6075
.31-.50
.50-.63
.63-.88.88-1.131.13-1.381.38-1.501.50-1.88
.50-.75
.75-.94.94-1.131.13-1.561.56-2.002.00-2.252.38-2.88
5101520355090
.921.223.664.889.4614.6430.00
1.892.802.993.504.294.967.09
1.84.46.69.7
18.026.075.1
1.101.501.932.602.873.634.33
.75
.981.221.381.772.132.95
.24
.32
.39
.59
.831.061.06
7.878.94
10.2411.2612.8014.4114.43
1.572.172.602.953.784.176.14
NCB-1319NCB-1924NCB-2432NCB-3241NCB-4150NCB-5060NCB-6075
NC-1924NC-2432NC-3241
STN-1924HSTN-2432HSTN-3241H
P-392P-392P-392
.831.001.301.692.132.383.07
�
FSH-14 FSM-8SB-1
49
Tip Clearance / Maximum Spread*:
0.24/3.16 inches
FSM/FSHSeries
Maximum Spread Force:
8-14 tonsMaximum Operating Pressure:
10,000 psi (FSH-14)
Stepped Blocks FSB-1
Use this pair of stepped blocks to increase wedge opening up to 3.16 in.
(81 mm). Fits both FSH-14 and FSM-8.
Hydraulic and Mechanical Industrial Spreaders
Shown: FSH-14 and FSM-8 with safety blocks SB1
• Integrated wedge concept: friction-free, smooth, parallel wedge movement eliminates flange damage and spreading arm failure
• Unique interlocking wedge design: no first step bending and risk of slipping out of joint
• Requires very small access gap of only .24 in. (6 mm)• Stepped spreader arm design: each step can spread
under full load• Few moving parts means durability and low maintenance• Safety block SB-1 and ratchet spanner SW-22 included
with FSM-8 • Safety block and Enerpac RC-102 cylinder
included with FSH-14
▼ Two FSH-14 spreaders used simultaneously with Enerpac handpump, hoses and AM-21 split-flow manifold. stepped
blocksFSB-1
Flange Spreader Sets
Hydraulic FSH-14 is available as a set (pump,
tool, gauge, adaptor and hose).
Set Includes: Set Model Number
Closed OpenedSafety Block Closed Opened
MechanicalHydraulic
Max. Spreading
Force(ton)
Tip Clearance
(in)
ModelNumber
Max. Spread*
(in)
Type Weight
(lbs)
Oil Capacity
(in3)
* Using stepped blocks FSB-1
814
.24
.24FSM-8FSH-14
3.163.16
14.315.7
FSH-14 P-392 HC-7206
STF-14HGA-2 GP-10S –
-4.76
.24
.98
.98
12.09
.86
1.21
1.33
2.38
10.7
3
11.3
1
.24
.59
1.211.21
1.33
2.38
11.3
1
12.7
9
.24
.59
1.21
3.90
.78
1.091.481.872.263.04
2.6 2.60
J
H
F
C
E
D
B
A
I
49
50 www.enerpac.com
�
Page:
Pipe Size (in)
FS-56 FS-109
Pin Type Hydraulic Flange Spreaders
Shown: FS-56
• Lightweight, ergono mic design for ease of use• Adjustable jaw widths from 2.75" to 8.50" for a wide
range of applications• Single-acting, spring return RC Series cylinders for fast
trouble-free operation
FS Series
Capacity:
5-10 tonsMaximum Operating Pressure:
10,000 psi
Maximum Flange
Thickness
(in)
Stud Size
(in)
Standard Wedge
(in)
Cap.
(tons)
Stroke
(in)
Oil Cap.
(in3)
Model Number
Min. Max.
Dimensions (in) Weight
(lbs)
Flange Spreader Matching Chart
ASA Rating
(psi)
Flange Spreader Sets
Both Hydraulic Flange Spreaders are available as sets (includes pump, tool, gauge, adaptor and hose).
Spreader Model Number
Set Model Number
Pump Model Number
Wedge Spreaders
Friction-free, smooth and parallel wedge movement with unique interlock wedge design. Eliminates
flange damage and risk of spreading arm failure.
2 x 2.252 x 3.63
.75-1.131.25-1.63
.13-1.13
.13-1.13510
1.502.13
1.504.80
2.754.10
6.108.50
7.716.00
3.454.50
1.001.50
8.1010.75
.751.25
2640
8.2511.00
3.004.25
FS-56FS-109
150300400500900
15002500
5-202.50-142.50-122.50-10.50-6
.50-3.50
.50-2.50
22-4216-2814-2412-208-164-83-4
1.281.98
FS-56FS-109FS-109
STF-56HSTF-109HSTF-109A
P-142P-392PATG-1102N
A B E F H I JD
C
�
WR-5 WR-15
48
51
A-92
• Single-acting, spring return• WR-15: For long stroke spreading applications• WR-5: For use in very confined work areas• A-92: Spreader attachment screws onto RC-Series
10 ton cylinders (except RC-101)
Hydraulic Wedgie and Spread Cylinders
Spreader Capacity
(tons)
Tip Clear ance
(in)
Cylinder Effective
Area
(in2)
Oil Capacity
(in3)
Wt.
(lbs)
Model Number
Shown clockwise from top: WR-15, WR-5, A-92
Capacity:
0.75-1 tonTip Clearance:
0.50-1.38 inchesMaximum Spread Range:
3.70-11.50 inchesMaximum Operating Pressure:
10,000 psi
A, WR Series
A WR-5 wedgie cylinder is used
to position a concrete block on
a construction site. �
Page:
Best Match Hand Pump
To power your Wedgie and Spreader attachment the P-392 Hand Pump is an ideal choice.
See the Enerpac E326 catalog for the full range of hand pump options.
MaximumSpread
(in)
Nut Cutters
Remove rusted or corroded nuts easily with Enerpac Nut Splitters. Hexagon nut capacities up to 2.88 in.
1.00.751.00
.501.261.38
1.002.25
–
.613.91
–
3.7011.506.25
5.025.08.0
WR-5WR-15A-92
2.00
2.75
9.63
1.38
6.25
21/4"-14UNS
3.62
2.01
.38
3.70
1.138.78
2.01
3/8"-18NPTF
3/8"-18NPTF
21.65
11.5
0
6.18
2.01
1.26
1.692.24
52 www.enerpac.com
�
�
�
�
�
Behavior of Bolts and Nuts
Elasticity is defined in Hooke’s Law of
physics: The stress in a bolt is directly
proportional to it’s strain. The stress-
strain of a bolt has an elastic range
and a plastic range. In the elastic
range Hooke’s Law is true.
All of the elongation applied within the
elastic range is relieved when the load
is removed. The amount of elongation
increases when more load is applied.
When a bolt is stressed beyond its
proof load (maximum load under
which a bolt will behave in elastic
manner), the elastic deformation
changes to plastic deformation and the
strain will no longer be proportional to
the stress.
In the plastic deformation a part of
the elongation will remain after the
load is removed. The point where
this permanent elongation occurs is
called the yield strength. The further
application of load takes the bolt to
a point where it begins to fail this is
termed it’s ultimate tensile strength
(UTS). At this UTS-point, if the bolt
continues to elongate with additional
force, it will finally break. The point
at which the bolt breaks is called the
tensile point.
Careful attention must be paid to
the grade of bolt being used as bolt
grades differ in the elastic range.
ke’s Law of Physics
Preload
The main purpose of the bolt and nut
is to clamp parts together with the
correct force to prevent loosening in
operation. The term preload refers to
the loading in a bolt immediately after
it has been tightened.
The amount of preload (residual load)
is critical as the joint can fail if the load
in the bolt is too high, too low or not
uniform in every bolt.
Uneven bolt loads can result in:
• Some bolts being loose while oth
are overloaded.
• Crushing of gasket at one side,
leakage on other side.
Preload is normally dictated by th
joint design, see Enerpac Informa
information on common joint type
contact your local representative
Uniform preload (residual load)
ElasticRange
Tensile Point
Strain
PlasticRange
BoltFailure
UltimateTensile
Point
Proof Load
Str
es
1. Bolt loosens due to cycle loads of
vibration.
2. Sealing face surface damage.
3. No compression.
4. Cracking.
5. Flange rotation.
6. Yielding of bolts.
7. Over compresion of gasket.
Over tight
Under tight
It iacto
WTurning movement
Torque Tightening
Stretch of Fastener
(Pre-load)
Force
Pressure:
1 psi = 0,069 bar
1 bar = 14,50 psi
= 10 N/cm2
1 kPa = 0,145 psi
1 MPa = 145 psi
Weight:
1 pound (lb) = 0,4536 kg
1 kg = 2,205 lbs
1 metric ton = 2205 lbs
= 1000 kg
1 ton (short) = 2000 lbs
= 907,18 kg
Temperature:
To Convert °C to °F:
T°F = (T°C x 1,8) + 32
To Convert °F to °C:
T°C = (T°F – 32) ÷ 1,8
1 in3
1 cm3 = 0,061 in
1 liter = 61,02 in3
= 0,264 gal
1 USgal = 3,785 cm3
= 3,785 l
= 231 in3
Other measurements:
1 in = 25,4 mm
1 mm = 0,039 in
1 ft = 0,3048 m
1 m = 3,2808 ft
1 in2 = 6,452 cm2
1 cm2 = 0,155 in2
1 hp = 0,746 kW
1 kW = 1,340 hp
1 Nm = 0,738 Ft.lbs
1 Ft.lbs = 1,356 Nm
1 kN = 224,82 lbs
1 lb = 4,448 N
to measurements
apacities and measurements in the
alog are expressed in uniform values.
conversion chart provides helpful
ormation for their translation into
uivalent systems.
l ton values specified in this catalogue
re metric tonnes and are for cylinder
class identification only.
Please refer to the kN data for
calculations.
Free Conversion Calculator
Visit enerpac.com and
download the free conversion
calculator.
Units to be
converted
International
System - S.I.
Nm
Imperial
Lbf.ft
M
Torque Conversion Factors
Key T
1 Lbf.ft1,356
1,000
1 Nm1,000
0,738
1 kgf.m9,807
7,233
D
SJ
D
SJ
METRIC SIZES
ThreadSize
D(mm)
HexagonSize
S(mm)
HexagonSize
J(mm)
instructio
recomme
bolted c
Individ
befor
DIB1
* Heavy hexagon nuts.
IMPERIAL SIZES
ThreadSize
D(inch)
Hexagon
Size *S
(inch)
HexagonSize
J(inch)
M 10
M 12
M 14
M 16
M 18
M 20
M 22
M 24
M 27
M 30
M 33
M 36
M 39
M 42
M 45
M 48
M 52
M 56
M 60
M 64
M 68
17
19
22
24
27
30
32
36
41
46
50
55
60
65
70
75
80
85
90
95
100
8
10
12
14
14
17
17
19
19
22
24
27
27 (30)
32
-
36
36
41
46
46
50
55
5/8"3/4"7/8"
1"
11/8"
11/4"
13/8"
11/2"
15/8"
13/4"
17/8"
2"
21/4"
21/2"
23/4"
3"
31/4"
11/16"
11/4"
17/16"
15/8"
113/16"
2"
23/16"
23/8"
29/16"
23/4"
215/16"
31/8"
31/2"
37/8"
41/4"
45/8"
5"
1/2"5/8"3/4"3/4"7/8"7/8"
1"
1"
-
11/4"
13/8"
15/8"
13/4"
17/8"
2"
21/4"
21/4"
54
56
58
60
61
Section
Bolting Theory
Torque Tightening
Tensioning
Bolt and Nut Sizes
Key to measurement
If selecting bolting tools is not your daily
routine, then you will appreciate these pages.
The ‘Yellow Pages’ are designed to help you
work with hydraulics. They will help you to
better understand the basics of bolting system
set-ups and of the most commonly used
bolting techniques. The better your choice of
equipment, the better you will appreciate these
tools. Take the time to go through these ‘Yellow
Pages’ and you will benefit even more from
Enerpac Bolting Solutions.
Enerpac ‘Yellow Pages’stand for
Technical Information!
Enerpac products are warranted to be free of defects in materials and work-manship. Any product that does not conform to specification will be repaired or replaced at Enerpac’s expense, anywhere in the world; simple as that !!
This warranty does not cover ordinary wear and tear, abuse, misuse, alterations, or the use of improper fluids. Determination of the authenticity of a warranty claim will be made only by Enerpac or its Authorized Service Centers.
www.enerpac.com
Visit our web site for the complete Global Lifetime Warranty or call your Authorized Service Center.
GLOBAL LIFETIME WARRANTY STATEMENT
Bolting Yellow Pages
Enerpac is certified for several quality standards. These standards require compliance with standards for management, administration, product development and manufacturing.
Enerpac works hard to maintain the ISO 9001 quality rating, in its ongoing pursuit of excellence.
CE Marking & Conformity
Enerpac provides Enerpac provides Declarations of Conformity, Declarations of Incorporation, and CE marking for products that conform to
the European Community Directives.
Where specified, Enerpac electric pump assemblies meet the design,
assembly and test requirements of the TÜV German Body.
EMC Directive 2004/108/ECWhere specified, Enerpac electric power pumps meet the requirements for Electro-magnetic Compatibility per EMC Directive 2004/108/EC.
II 2 GD ck T4
The ZA-series pumps are tested and certified according to the Directive 94 / 9 / EC“ATEX Directive”. The explosion protection is for equipment group II, equipment category 2 (hazardous area zone 1), in gas and/or dust atmospheres. The ZA-series pumps are marked with: Ex II 2 GD ck T4.
ASME B30.1–2004Our cylinders fully comply with the criteria set forth by the American Society of Mechanical Engineers (except RD series).
DIN 20024Enerpac thermoplastic hoses are related to the criteria set forth in Deutsche Industrie Norm 20024.
Product Design CriteriaAll hydraulic components are designed and tested to be safe for use at maximum 10,000 psi unless otherwise specifically noted.
ISO 9001REGISTERED
ENERPAC, 720 W. James St., Columbus, WI 53925 USA
KEMA 0602
53
A
D
E
C B
Bolting Solution and Application Worksheet
� Please complete the following information prior contacting Enerpac for your bolting proposal:
Requested By: ________________________________________________________________ Requested Date: ______________________
Company: ____________________________________________________ Industry: ______________________________________________
Contact: _____________________________________________________ Title: __________________________________________________
Phone: _________________________ Fax: ________________________ Email: _________________________________________________
Description of Application (provide drawings if possible):_______________________________________________________________________________________________________________________
_______________________________________________________________________________________________________________________
_______________________________________________________________________________________________________________________
_______________________________________________________________________________________________________________________
Type of Application:
_______________________________________________________________________________________________________________________
_______________________________________________________________________________________________________________________
APPLICATION TECHNICAL DATA
Bolt Quantity: _____________________
Bolt Diameter: ____________________
Bolt Threads per Inch/Pitch: _______
Bolt Grade: _______________________
Bolt Coating: _____________________
Gasket Type: _____________________
App. Operating Temp., °C or °F:
__________________________________
Known Bolting Values:
� Load(Lbs. / kN) ________________________% of Yield (psi/Nmm2)
� Stretch-Bolt Length(In. / mm) _________________________
� Turn of Nut(Preload / Degrees) ________________
� Torque(Ft.lbs / Nm / Kgm) _________________
Application Position:
� Top-side � Vertical � Inverted
Specify Dimensions: INCH MM (Metric)
A _________ B __________ C ___________ D __________ E ___________
Distance to Closure: __________________________________________________
Current Lubrication: Type _______________ Brand _________________
54 www.enerpac.com
Bolting Theory
Function of Bolts and Nuts
Threaded fasteners are used across industry to assemble products ranging from pipelines to heavy-duty earth movers and from cranes to bridges and many more. Their principle function is to create a clamping force across the joint which is able to sustain the operating conditions without loosening.
Correctly tightened bolts make use of their elastic properties, to work well they must behave like springs. When load is applied, the bolt stretches and tries to return to its original length. This creates compressive force across the joint members.
Behavior of Bolts and Nuts
Elasticity is defined in Hooke’s Law of physics: The stress in a bolt is directly proportional to its strain. The stress-strain of a bolt has an elastic range and a plastic range. In the elastic range Hooke’s Law is true.
All of the elongation applied within the elastic range is relieved when the load is removed. The amount of elongation increases when more load is applied. When a bolt is stressed beyond its proof load (maximum load under which a bolt will behave in an elastic manner), the elastic elongation changes to plastic deformation and the strain will no longer be proportional to the stress.
In the plastic deformation a part of the elongation will remain after the load is removed. The point where this permanent elongation occurs is called the yield strength. The further application of load takes the bolt to a point where it begins to fail this is termed its ultimate tensile strength (UTS). At this UTS-point, if additional force is applied to the bolt it will continue to elongate until it finally breaks. The point at which the bolt breaks is called the tensile point.
Careful attention must be paid to the grade of bolt being used as bolt grades differ in the elastic range.
Hooke’s Law of Physics
Preload
The main purpose of a bolt and nut is to clamp parts together with the correct force to prevent loosening in operation. The term preload refers to the loading in a bolt immediately after it has been tightened.
The amount of preload (residual load) is critical as the joint can fail if the load in the bolt is too high, too low or not uniform in every bolt.
Uneven bolt loads can result in:• Some bolts being loose while others
are overloaded. • Crushing of the gasket on one side,
leakage on the other side.
Preload is normally dictated by the joint design, (see Enerpac Bolted Joint Integrity) for information on common joint types or contact your local representative.
Uniform preload (residual load)
ElasticRange
Tensile Point
Strain
PlasticRange
Bolt Failure
UltimateTensile Point
Proof Load
Str
ess
1. Bolt loosens due to cycle loads of vibration.
2. Sealing face surface damage.3. No compression.4. Cracking.5. Flange rotation.6. Yielding of bolts.7. Over compression of gasket.
Over tightUnder tight
55
Bolting Theory
Tightening Methods
Advantages of Controlled Tightening
Known, controllable and accurate bolt loads
Employs tooling with controllable outputs and adopts calculation to determine the required tool settings.
Uniformity of bolt loading
Especially important on gasketed joints as an even and consistent compression is required for the gasket to be effective.
Safe operation following prescribed procedures
Eliminates the dangerous activities of manual uncontrolled tightening and requires that the operators be skilled and follow procedures.
Reduces operational time resulting in increased productivity
Reduces tightening time and operator fatigue by replacing manual effort with the use of controlled tooling.
Reliable and repeatable results
Using calibrated, tested equipment, following procedures and employing skilled operators achieves known results consistently.
The right results first time
Many of the uncertainties surrounding in-service joint failures are removed by ensuring the correct assembly and tightening of the joint are carried out the first time.
Principally there are two modes of tightening: "Uncontrolled" and "Controlled".
Uncontrolled tightening Uses equipment and/or procedures
that cannot be measured. Preload is applied to a bolt and nut assembly using a hammer and spanner or other types of impact tools.
Controlled tightening Employs calibrated and measurable
equipment, follows prescribed procedures and is carried out by trained personnel. There are two main techniques: Torque tightening and Bolt tensioning.
1) Torque tightening - Achieves preload in a bolt and nut assembly via the nut in a controlled manner using a tool.
2) Bolt tensioning - Achieves preload in a bolt and nut assembly by stretching the bolt axially using a tool.
Bolting Integrity Software
A comprehensive on-line software solution for Bolted Joint Integrity.
Integral databases hold data for:
• BS1560, MSS SP44, API 6A and 17D fl anged joints
• Common gasket materials and confi gurations
• Comprehensive range of bolt materials
• Comprehensive range of lubricants
• Enerpac's Controlled Bolting Equipment including: Torque Multipliers, Hydraulic Wrenches and Bolt Tensioning tools
Custom Joint information can also be entered.
The software offers Tool selection, Bolt Load calculations and Tool pressure settings, as well as, a combined Application data sheet and Joint completion report.
Visit www.enerpac.com to access our free on-line bolting software application and obtain information on tool selection, bolt load calculations and tool pressure settings. A combined application data sheet and joint completion report is also available.
56 www.enerpac.com
What is Torque?
It is a measure of how much force acting on an object which causes that object to rotate.
What is Torque Tightening?The application of preload to a fastener by the turning of the fastener’s nut.
Torque Tightening and Preload
The amount of preload created when torqueing is largely dependant on the effects of friction.
Principally there are three different “torque components”: • torque to stretch the bolt• torque to overcome the friction in
bolt and nut threads• torque to overcome friction at the
nut spot face (bearing contact surface).
Torque Tightening
Friction points should always be lubricated when using the torque tightening method.
Preload (residual load) = Applied Torque minus Frictional Losses
Lubrication Reduces Friction
Lubrication reduces the friction during tightening, decreases bolt failure during installation and increases bolt service life. Variation in friction coefficients affect the amount of preload achieved at a specified torque. Higher friction results in less conversion of torque to preload. The value for the friction coefficient provided by the lubricant manufacturer must be known to accurately establish the required torque value.
Lubricant or anti-seizure compounds should be applied to both the nut bearing surface and the male threads.
Frictional Losses
Example of how a lubricant can reduce the effect of friction and convert more torque to bolt preload.
Frictional Losses (dry steel bolt)
Turning movement
Torque Tightening
Stretch of Fastener(Pre-load)
Force
10% convertedto preload
50% at nut face
Lubricated with Moly grease (µ = 0.1) Light oil (µ = 0.15) Dry unlubricated (µ = 0.2)
Res
idua
l Bo
lt L
oad
(ton
s) �
Torque (ft.lbs) �(Applied load)
Lubrication Reduces Friction40% in threads
11
10
9
8
7
6
5
4
3
2
1
00 20 40 60 80 100 120
57
15
59
333
7
711
2226
610
4
8
11
44
812
��yy
��yy
Step 1 Spanner tight ensuring that 2-3 threads extend above nut
Step 2 Tighten each bolt to one-third of the final required torque following the pattern as shown above.
Step 3 Increase the torque to two-thirds following the pattern shown above.
Step 4 Increase the torque to full torque following the pattern shown above.
Step 5 Perform one final pass on each bolt working clockwise from bolt 1, at the full final torque.
Read Instruction Manuals
Please refer to the product Instruction Sheets for safe use guidelines and detail on the
correct set up and operation of the equipment.Breakout Torque
When loosening bolts a torque value higher than the tightening torque is normally required. This is mainly due to corrosion and deformations in the bolt and nut threads.
Breakout torque cannot be accurately calculated, however, depending on conditions it can take up to 2½ times the input torque to breakout.
The use of penetrating oils or anti-seize products is always recommended when performing breakout operations.
Manufacturer’s rating of pressure and torque are maximum safe limits. Good practice encourages using only 80% of these ratings!
Select the Right Wrench
Choose your Enerpac torque wrench using the untightening rule of thumb:
• When loosening a nut or bolt more torque is usually required than when tightening.
• For general conditions it can take up to 2½ times the input torque to breakout.
• Do not apply more than 75% of the maximum torque output of the tool when loosening nuts or bolts.
Conditions of bolted joints• Humidity corrosion (rust) requires up
to twice the torque required for tightening.
• Sea water and chemical corrosion requires up to 21⁄2 times the torque required for tightening.
• Heat corrosion requires up to 3 times the torque required for tightening.
Torque Tightening
Torque Procedure
When torquing it is common to tighten only one bolt at a time, this can result in Point Loading and Load Scatter. To avoid this, torque is applied in stages following a prescribed pattern:
Torque Sequence
58 www.enerpac.com
Tensioning
Tensioning requires longer bolts
What is Bolt Tensioning
Tensioning is the direct axial stretching of the bolt to achieve preload. Inaccuracies created through friction are eliminated. Massive mechanical effort to create torque is replaced with simple hydraulic pressure. A uniform load can be applied by tensioning multiple studs simultaneously.
Tensioning requires longer bolts, and a seating area on the assembly around the nut. Tensioning can be done using detachable Bolt Tensioners or Hydraulic Nuts.
What is Load Loss
Load loss is a loss of bolt elongation depending on factors such as thread deflections, radial expansion of the nut, and embedding of the nut into the contact area of the joint. Load loss is accounted for in calculation and is added to the preload value to determine the initial Applied Load.
The preload depends on Applied Load and Load Loss (load loss factor).
INCORRECT
CORRECT
L Minimum = 1 X D
Preload (residual load) = Applied Load minus Load Losses
GLOSSARY OF TERMS
Applied Load: The load applied to a bolt during tensioning which includes an allowance for Load Loss.
Bolt Tensioning: A method of controlled tightening which applies preload to a bolt by stretching it axially.
Breakout Torque: The amount of torque required to loosen a tightened bolt. (Usually more torque is required to loosen a bolt than was used to tighten it.)
Elastic Range: The range on a bolt's stress / strain curve where stress is directionally proportional to strain.
Load Loss: The losses in a bolt which occur on transfer of load from a tensioning device to the bolt assembly (these may arise from phenomena such as thread deflection and embedding of
the nut to the contact area of the joint, and is calculated as a factor of the length to diameter ratio of the bolt).
Load Scatter: The spread of differing loads in a sequence of bolts after they have been loaded. It is mostly due to the elastic interaction of the bolts and the joint member; as subsequently tightened bolts further compress the joint, previously tightened bolts are subject to some relaxation.
Plastic Range: The range on a stress/strain curve where the tensile load applied to a bolt results in permanent deformation.
Preload: The load in a bolt immediately after it has been tightened.
Proof Load: Proof load is often used interchangeably with Yield Strength but is usually measured at 0.2% plastic strain.
Tensile Point: The point at which the tensile loading on a bolt causes the bolt to rupture.
Torque Tightening: The application of Preload to a bolt by turning of the bolt's nut.
Ultimate Strength: The maximum tension which can be created by tensile load on a bolt.
Yield Strength: The point at which a bolt begins to plastically deform under tensile loading.
NOTE: Bolt is used as a generic term for a threaded fastener.
59
��yy
��yyTensioning
Step 1 Step 2 Step 3 Step 4
General Procedure
Step 1: The bolt Tensioner is fitted over the stud
Step 2: Hydraulic pressure is applied to the tensioner which then stretches the stud.
Step 3: The Stud’s nut is wound down against the joint face
Step 4: Pressure is released and the tool removed.
The bolt behaves like a spring, when the pressure is released the bolt is under tension and attempts to contract, creating the required clamping force across the joint.
Read Instruction Manuals
Please refer to the product Instruction Sheets for safe use guidelines and detail on the
correct set up and operation of the equipment.
Less than 100% Tensioning
Not all applications allow for the simultaneous fit of a tensioning device on each bolt, in these cases at least two tensioning pressures are applied. This is to account for a load loss in those bolts already tensioned as the next sets are tightened. The load losses are accounted for in calculation and a higher load is applied to allow the first sets to relax back to the target preload.
Tensioning Operation
Tensioning permits the simultaneous tightening of multiple bolts; the tools are connected in sequence via a high-pressure hose assembly to a single pump unit. This ensures each tool develops the exact same load and provides a uniform clamping force across the joint. This is especially important for pressure containing vessels requiring even gasket compression to affect a seal.
Set-up using a 100% tensioning procedure
All bolts are tensioned simultaneously.
Set-up using a 50% tensioning procedure
Half the bolts are tensioned simultaneously, the tools are relocated on the remaining bolts and they are subsequently tensioned.
Manufacturer’s rating of pressure and load are maximum safe limits. Good practice encourages using only 80% of these ratings!
60 www.enerpac.com
D
S J
D
S J
METRIC SIZES
ThreadSize
D(mm)
HexagonSize
S(mm)
HexagonSize
J(mm)
Determine the maximum torque according to the bolt (nut) size and grade. Always consult the manufacturers
instructions or engineering recommendations when making bolted connections.
IMPORTANT
The hexagon sizes shown in the tables should be used as a guide only. Individual sizes
should be checked before specifying any equipment.
Use only Heavy Duty Impact Sockets for power driven torquing equipment, according to ISO2725 and ISO1174;
DIN3129 and DIN3121 or ASME-B107.2/1995.
* Heavy hexagon nuts.
IMPERIAL SIZES
ThreadSize
D(in)
HexagonSize *
S(in)
HexagonSize
J(in)
Hexagon Nut and Bolt Sizes
M 10M 12M 14M 16M 18M 20M 22M 24M 27M 30M 33M 36M 39M 42M 45M 48M 52M 56M 60M 64M 68M 72M 76M 80M 85M 90M 95M 100M 105M 110M 115M 120M 125M 130M 140M 150
1719222427303236414650556065707580859095100105110115120130135145150155165170180185200210
81012141417171919222427
27 (30)32-
36364146465055606570
70 (75)-
85--------
5/8"3/4"7/8"1"
11/8"11/4"13/8"11/2"15/8"13/4"17/8"2"
21/4"21/2"23/4"3"
31/4"
11/16"11/4"17/16"15/8"
113/16"2"
23/16"23/8"29/16"23/4"
215/16"31/8"31/2"37/8"41/4"45/8"5"
1/2"5/8"3/4"3/4"7/8"7/8"1"1"-
11/4"13/8"15/8"13/4"17/8"2"
21/4"21/4"
61
AA . . . . . . . . . . . . 51 ATM . . . . . . . . . . 47ATP . . . . . . . . . . 42
BBSH . . . . . . . . . 10
EE . . . . . . . . . . . 4-5ESS . . . . . . . . . . 46
FFS . . . . . . . . . . . 50FSH . . . . . . . . . . 49FSM . . . . . . . . . 49
GGT . . . . . . . . 40-41
HHPT . . . . . . . . . 43HT . . . . . . . . . . . 43HXD . . . . . . 24-27
NNC . . . . . . . . . . 48
PPMU . . . . . . 28-29PTA . . . . 28, 34-35
RRTE . . . . . . . . . . . 9
SS . . . . . . . . . . 7, 28SCH . . . . . . . . . 45SCR . . . . . . . . . 45SDA . . . . . . . . . . 8SRS . . . . . . . .9, 19SQD . . . 20-23,28
TTHC . . . . . . . . . 28THQ . . . . . . . . . 28TSP . . . . . . . . 9, 19
WW . . . . . 12-18, 28WTE . . . . . . . . . 19WR . . . . . . . . . . 51
ZZA4T . . . 28, 36-39ZU4 . . . . 28, 30-33
�
Pressure:1 psi = 0,069 bar1 bar = 14,50 psi = 10 N/cm2
1 kPa = 0,145 psi1 MPa = 145 psi
Force:1 lbf = 4.45 N1 klbf = 1000 lbf1 kN = 1000 N
Weight:1 pound (lb) = 0,4536 kg1 kg = 2,205 lbs1 metric ton = 2205 lbs = 1000 kg1 ton (short) = 2000 lbs = 907,18 kg
Temperature:To Convert °C to °F:T°F = (T°C x 1,8) + 32
To Convert °F to °C:T°C = (T°F – 32) ÷ 1,8
Volume:1 in3 = 16,387 cm3
1 cm3 = 0,061 in3
1 liter = 61,02 in3
= 0,264 gal1 US gal = 3,785 cm3
= 3,785 l = 231 in3
Other measurements:1 in = 25,4 mm1 mm = 0,039 in1 ft = 0,3048 m1 m = 3,2808 ft1 in2 = 6,452 cm2
1 cm2 = 0,155 in2
1 hp = 0,746 kW1 kW = 1,340 hp1 Nm = 0,738 Ft.lbs1 Ft.lbs = 1,356 Nm1 kN = 224,82 lbs1 lb = 4,448 N
Key to measurements
All capacities and measurements in the catalog are expressed in uniform values.
The conversion chart provides helpful information for their translation into equivalent systems.
Free Conversion Calculator
Visit enerpac.com and download the
free conversion calculator.
Units to beconverted
InternationalSystem - S.I.Nm
Imperial
Lbf.ft
Metric
kgf.m
Torque Conversion Factors
Key To Measurements
Inches Decimal mm
Model Number Index
Page(s) � Page(s) � Page(s) � Page(s) �
FDM Conversion Chart
1 Ft.lbs
1 Nm
1 kgf.m
1,356 1,000 0,138
1,000 0,738 0,102
9,807 7,233 1,000
1,59 3,18 4,76 6,35 7,94 9,53 11,11 12,70 14,29 15,88 17,46 19,05 20,64 22,23 23,81 25,40
0.06 0.13 0.19 0.25 0.31 0.38 0.44 0.50 0.56 0.63 0.69 0.75 0.81 0.88 0.94 1.00
1⁄16
⅛
3⁄16
¼
5⁄16
⅜
7⁄16
½
9⁄16
⅝
11⁄16
¾
13⁄16
7�8
15⁄16
1
e-mail: info@enerpac.com
Internet: www.enerpac.com
AfricaENERPAC Middle East FZEOffice 423, JAFZA 15P.O. Box 18004Jebel Ali, DubaiUnited Arab EmiratesTel: +971 (0)4 8872686Fax: +971 (0)4 8872687
Australia and New ZealandActuant Australia Ltd. Block V Unit 3Regents Park Estate391 Park RoadRegents Park NSW 2143(P.O. Box 261) AustraliaTel: +61 297 438 988Fax: +61 297 438 648
Brazil Power Packer do Brasil Ltda.Rua dos Inocentes, 58704764-050 - Sao Paulo (SP)Tel: +55 11 5687 2211Fax: +55 11 5686 5583Toll Free: 0800 891 5770vendasbrasil@enerpac.com
CanadaActuant Canada Corporation6615 Ordan Drive, Unit 14-15Mississauga, Ontario L5T 1X2Tel: +1 905 564 5749Fax: +1 905 564 0305Toll Free:Tel: +1 800 268 4987Fax: +1 800 461 2456Technical Inquiries:techservices@enerpac.com
ChinaActuant Industries Co. Ltd.No. 6 Nanjing Road,Taicang Economic Dep ZoneJiangsu, ChinaTel: +86 0512 5328 7529 +86 0512 5328 7500 7529 Fax: +86 0512 5335 9690
Actuant China Ltd. (Peking)709B Diyang BuildingXin No. 2, Dong San Huan North Rd. Beijing City, 100028 China Tel: +86 10 845 36166 Fax: +86 10 845 36220
France, Switzerland francophoneENERPAC Une division de ACTUANT France S.A.ZA de Courtaboeuf32, avenue de la Baltique 91140 VILLEBON /YVETTEFranceTel: +33 1 60 13 68 68Fax: +33 1 69 20 37 50
Germany, Austria, Switzerland, Greece, Baltic States, Central and Eastern EuropeENERPAC GmbHP.O. Box 300113D-40401 DüsseldorfWillstätterstrasse 13D-40549 Düsseldorf GermanyTel: +49 211 471 490Fax: +49 211 471 49 28
IndiaENERPAC Hydraulics Pvt. Ltd.No. 1A, Peenya Industrial AreaIInd Phase, Bangalore, 560 058IndiaTel: +91 80 40 792 777Fax: +91 80 40 792 792
ItalyENERPAC S.p.A.Via Canova 420094 Corsico (Milano)Tel: +39 02 4861 111Fax: +39 02 4860 1288
JapanApplied Power Japan LTD KKBesshocho 85-7Kita-ku, Saitama-shi 331-0821JapanTel: +81 48 662 4911Fax: +81 48 662 4955
Middle East, Turkey and Caspian SeaENERPAC Middle East FZEOffice 423, JAFZA 15P.O. Box 18004Jebel Ali, DubaiUnited Arab EmiratesTel: +971 (0)4 8872686Fax: +971 (0)4 8872687
Russia and CIS (excl. Caspian Sea Countries) Actuant LLCAdmiral Makarov Street 8125212 MoscowRussiaTel: +7-495-9809091Fax: +7-495-9809092
SingaporeActuant Asia Pte Ltd.37C, Benoi Road Pioneer Lot,Singapore 627796Tel: +65 68 63 0611Fax: +65 64 84 5669Toll Free:Tel: +1800 363 7722Technical Inquiries:techsupport@enerpac.com.sg
South KoreaActuant Korea Ltd.3Ba 717,Shihwa Industrial ComplexJungwang-Dong, Shihung-Shi, Kyunggi-DoRepublic of Korea 429-450Tel: +82 31 434 4506Fax: +82 31 434 4507
Spain and PortugalENERPAC SPAIN, S.L. Avda. Los Frailes, 40 – Nave C & DPol. Ind. Los Frailes28814 DAGANZO DE ARRIBA(Madrid) SpainTel: +34 91 661 11 25Fax: +34 91 661 47 89
Sweden, Denmark, Norway, Finland and IcelandEnerpac Scandinavia ABFabriksgatan 7412 50 GothenburgSwedenTel: +46 (0) 31 7990281Fax: +46 (0) 31 7990010Inquiries:Scandinavianinquiries@enerpac.com
The Netherlands, Belgium and LuxembourgENERPAC B.V.Galvanistraat 115, 6716 AE Ede P.O. Box 8097, 6710 AB EdeThe NetherlandsTel: +31 318 535 911Fax: +31 318 525 613 +31 318 535 848Inquiries:beneluxinquiries@enerpac.com
United Kingdom and IrelandENERPAC Ltd., Bentley Road SouthDarlaston, West MidlandsWS10 8LQ, EnglandTel: +44 (0)121 50 50 787Fax: +44 (0)121 50 50 799
USA, Latin America and CaribbeanENERPAC P.O. Box 32416100 N. Baker Road Milwaukee, WI 53209 USATel: +1 262 781 6600Fax: +1 262 783 9562User inquiries: +1 800 433 2766Distributor inquiries/orders: +1 800 558 0530Technical Inquiries:techservices@enerpac.com
Enerpac Worldwide Locations
Your Enerpac Distributor:
030101608-601 -R1 US © 2008 Enerpac - Subject to change without notice.
Bolting Solutions
Email: info@enerpac.comInternet: www.enerpac.com
top related