Transcript
Have ALWAYS been right behind the MIRACLE
Air-Cooled Type Screw Chiller
CLK Corporation
Keep on building our PRIDE ONLY through the TRUST
8th~9th Floor, E.C.F.C. Building, 19-7, Nonhyun-dong, Gangnam-gu Seoul, Korea [135-010]
Telephone: +82-2-3441-2586, 8850, 2582 / Fax: +82-2-544-2583 / E-mail: OverseasSales@carrier.co.kr
Copyrightⓒ2013 CLK Co. All rights reserved.
CLK Corporation
Air-Cooled Type Screw Chiller - 27.2 usRT
• Model : 12S002UH (27.2 usRT) • Dimension(Length x Width x Height)
- 2,210 x 1,900 x 2,175 mm
• Net Weight : 1,720 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 82,250 76,900
usRT 27.2 25
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 34.3 37.5
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 30ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 22 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 274 256
Pressure Drop mAq 2.3
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 1,040
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 0.75 kW x 4
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 80
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 33.2 usRT
• Model : 12S003UH (33.2 usRT) • Dimension(Length x Width x Height)
- 2,210 x 1,900 x 2,175 mm
• Net Weight : 1,760 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 100,250 94,000
usRT 33.2 31
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 41.3 45.3
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 40ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 30 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 334 313
Pressure Drop mAq 2.3
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 1,032
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 0.75 kW x 4
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 80
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 41.0 usRT
• Model : 12S004UH (41.0 usRT) • Dimension(Length x Width x Height)
- 2,210 x 1,900 x 2,175 mm
• Net Weight : 1,870 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 123,900 115,800
usRT 41.0 38
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 51.3 56.2
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 413 386
Pressure Drop mAq 2.3
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 1,280
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 4
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 80
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 50.3 usRT
• Model : 12S005UH (50.3 usRT) • Dimension(Length x Width x Height)
- 2,210 x 1,900 x 2,175 mm
• Net Weight : 1,950 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 152,100 142,300
usRT 50.3 47
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 62.0 68.3
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 507 474
Pressure Drop mAq 2.3
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 1,280
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 4
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 100
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 66.3 usRT
• Model : 12S007UH (66.3 usRT) • Dimension(Length x Width x Height)
- 4,140 x 1,900 x 2,200 mm
• Net Weight : 3,220 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 200,500 188,000
usRT 66.3 62
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 82.5 90.5
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 40ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 30 x 2
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 2, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 668 627
Pressure Drop mAq 2.0
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 2,064
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 0.75 kW x 8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 7.5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 81.9 usRT
• Model : 12S008UH (81.9 usRT) • Dimension(Length x Width x Height)
- 4,140 x 1,900 x 2,200 mm
• Net Weight : 3,420 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 247,800 231,500
usRT 81.9 77
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 102.5 112.4
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 2
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 2, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 826 772
Pressure Drop mAq 2.0
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 2,560
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 0.75 kW x 8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 7.5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 100.6 usRT
• Model : 12S010UH (100.6 usRT) • Dimension(Length x Width x Height)
- 4,140 x 1,900 x 2,200 mm
• Net Weight : 3,670 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 304,200 284,500
usRT 100.6 94
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 124.0 136.5
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 2
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,014 948
Pressure Drop mAq 2.0
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 2,560
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 7.5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 122.9 usRT
• Model : 12S012UH (122.9 usRT) • Dimension(Length x Width x Height)
- 6,065 x 1,900 x 2,200 mm
• Net Weight : 4,980 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 371,800 347,300
usRT 122.9 115
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 153.8 168.6
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 3
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 3, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,239 1,158
Pressure Drop mAq 3.3
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 3,840
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 12
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 150.9
• Model : 12S015UH (150.9) • Dimension(Length x Width x Height)
- 6,065 x 1,900 x 2,200 mm
• Net Weight : 5,340 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 456,300 426,800
usRT 150.9 141
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 186.0 204.8
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 3
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 3, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,521 1,423
Pressure Drop mAq 3.3
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 3,840
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 12
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 163.9 usRT
• Model : 12S016UH (163.9 usRT) • Dimension(Length x Width x Height)
- 7,990 x 1,900 x 2,200 mm
• Net Weight : 6,600 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller - Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 495,700 463,000
usRT 163.9 153
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 205.0 224.8
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 4
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 4, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,652 1,543
Pressure Drop mAq 3.5
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 5,120
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 16
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 3.75, 15 ~ 100%(Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 150
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Air-Cooled Type Screw Chiller – 201.2 usRT
• Model : 12S020UH (201.2 usRT) • Dimension(Length x Width x Height)
- 7,990 x 1,900 x 2,200 mm
• Net Weight : 7,070 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Outdoor Air Condition °C DB 35 40
Cooling Capacity kcal/h 608,300 569,000
usRT 201.2 188
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Total Input (Comp. + Fan) kW 248.0 273.0
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 4
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 4, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 2,028 1,897
Pressure Drop mAq 3.5
Condenser Type - Cross Fin Tube Type
Fan
Type - Propeller Fan
Air Flow Rate m3/min 5,120
Condensing
Pressure Control
Type - Controlling the Number of Operation Fans
Air Flow % 100 - 50 - 0
Motor Nom. Output x Q’ty - 1.12 kW x 16
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 3.75, 15 ~ 100%(Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 150
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
Have ALWAYS been right behind the MIRACLE
Water-Cooled Type Screw Chiller (Hitachi)
CLK Corporation
Keep on building our PRIDE ONLY through the TRUST
8th~9th Floor, E.C.F.C. Building, 19-7, Nonhyun-dong, Gangnam-gu Seoul, Korea [135-010]
Telephone: +82-2-3441-2586, 8850, 2582 / Fax: +82-2-544-2583 / E-mail: OverseasSales@carrier.co.kr
Copyrightⓒ2013 CLK Co. All rights reserved.
CLK Corporation
Water-Cooled Type Screw Chiller – 30.0 usRT
• Model : 13S003UH (30.0 usRT) • Dimension(Length x Width x Height)
- 2,170 x 1,045 x 1,460 mm
• Net Weight : 1,180 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 90,600
usRT 30.0
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 26.2
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 30ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 22 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 302
Pressure Drop mAq 2.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 377
Pressure Drop mAq 1.8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 80
Cooling Water Pipe mm 65
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 36.5 usRT
• Model : 13S004UH (36.5 usRT) • Dimension(Length x Width x Height)
- 2,170 x 1,070 x 1,510 mm
• Net Weight : 1,230 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 110,400
usRT 36.5
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 31.9
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 40ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 30 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 368
Pressure Drop mAq 2.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 459
Pressure Drop mAq 2.5
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 80
Cooling Water Pipe mm 80
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 45.1 usRT
• Model : 13S005UH (45.1 usRT) • Dimension(Length x Width x Height)
- 2,170 x 1,070 x 1,510 mm
• Net Weight : 1,330 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 136,300
usRT 45.1
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 38.9
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 454
Pressure Drop mAq 2.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 566
Pressure Drop mAq 1.8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 100
Cooling Water Pipe mm 80
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 55.4 usRT
• Model : 13S006UH (55.4 usRT) • Dimension(Length x Width x Height)
- 2,170 x 1,110 x 1,545 mm
• Net Weight : 1,400 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 167,500
usRT 55.4
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 48.3
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 1
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 558
Pressure Drop mAq 2.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 697
Pressure Drop mAq 1.8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 15 ~ 100% (Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 100
Cooling Water Pipe mm 100
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 73.0 usRT
• Model : 13S007UH (73.0 usRT) • Dimension(Length x Width x Height)
- 2,800 x 1,540 x 1,450 mm
• Net Weight : 2,150 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 220,800
usRT 73.0
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 63.9
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 40ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 30 x 21
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 2, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 736
Pressure Drop mAq 2.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 919
Pressure Drop mAq 4.5
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 7.5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 100
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 90.2 usRT
• Model : 13S009UH (90.2 usRT) • Dimension(Length x Width x Height)
- 2,800 x 1,565 x 1,450 mm
• Net Weight : 2,520 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 272,700
usRT 90.2
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 77.9
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 2
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 2, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 909
Pressure Drop mAq 2.0
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 1,132
Pressure Drop mAq 4.5
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 7.5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 100
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 110.8 usRT
• Model : 13S012UH (110.8 usRT) • Dimension(Length x Width x Height)
- 2,800 x 1,565 x 1,450 mm
• Net Weight : 2,700 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 335,700
usRT 110.8
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 96.8
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 2
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 2, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,117
Pressure Drop mAq 2.0
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 1,394
Pressure Drop mAq 4.5
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 7.5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 100
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 135.3 usRT
• Model : 13S014UH (135.3 usRT) • Dimension(Length x Width x Height)
- 3,600 x 1,575 x 1,450 mm
• Net Weight : 3,250 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 409,000
usRT 135.3
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 116.8
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 3
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 3, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,363
Pressure Drop mAq 3.6
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 1,698
Pressure Drop mAq 3.4
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 166.2 usRT
• Model : 13S017UH (166.2 usRT) • Dimension(Length x Width x Height)
- 3,600 x 1,575 x 1,450 mm
• Net Weight : 3,540 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 502,500
usRT 166.2
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 145.1
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 3
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 3, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,675
Pressure Drop mAq 3.6
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 2,091
Pressure Drop mAq 3.5
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 5, 15 ~ 100% (Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 180.3 usRT
• Model : 13S018UH (180.3 usRT) • Dimension(Length x Width x Height)
- 4,030 x 1,635 x 1,525 mm
• Net Weight : 4,500 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 545,300
usRT 180.3
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 155.8
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 50ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 37 x 4
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 4, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,818
Pressure Drop mAq 3.8
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 2,264
Pressure Drop mAq 3.8
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 3.75, 15 ~ 100%(Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 150
Cooling Water Pipe mm 150
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 221.6 usRT
• Model : 13S022UH (221.6 usRT) • Dimension(Length x Width x Height)
- 4,030 x 1,635 x 1,525 mm
• Net Weight : 4,800 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices - High performance Micro Process Controller
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 670,000
usRT 221.6
Power
Main Supply - 3Ph x AC 220 / 380 / 440V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 193.4
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - 60ASC-Z / Hitachi, Japan
Nominal Output x Q’ty kW 45 x 4
Starting Method - Y - △
Lubricating Oil ℓ 6 ℓ x 4, Freol UX300
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 2,233
Pressure Drop mAq 4.0
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 2,788
Pressure Drop mAq 4.0
Controller - Micro Process Controller
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 3.75, 15 ~ 100%(Number of Operating Comp. & Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 150
Cooling Water Pipe mm 150
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
Water-Cooled Type Screw Chiller (Refcomp)
Have ALWAYS been right behind the MIRACLE
Keep on building our PRIDE ONLY through the TRUST
CLK Corporation
8th~9th Floor, E.C.F.C. Building, 19-7, Nonhyun-dong, Gangnam-gu Seoul, Korea [135-010]
Telephone: +82-2-3441-2586, 8850, 2582 / Fax: +82-2-544-2583 / E-mail: OverseasSales@carrier.co.kr
CLK Corporation
Water-Cooled Type Screw Chiller – 70.7 usRT
• Model : 13S007UR (70.7 usRT) • Dimension(Length x Width x Height)
- 2,500 x 900 x 1,860 mm
• Net Weight : 1,780 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 213,660
usRT 70.7
Power
Main Supply - 3Ph x AC 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 61.5
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-255 / Refcomp
Nominal Output x Q’ty kW 60 x 1
Starting Method - Y - △
Lubricating Oil ℓ 11 ℓ, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 712
Pressure Drop mAq 2.7
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 889
Pressure Drop mAq 4.0
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 100
Cooling Water Pipe mm 100
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 85.5 usRT
• Model : 13S009UR (85.5 usRT) • Dimension(Length x Width x Height)
- 2,700 x 950 x 2,120 mm
• Net Weight : 2,040 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 258.660
usRT 85.5
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 74.0
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-305 / Refcomp
Nominal Output x Q’ty kW 75 x 1
Starting Method - Y - △
Lubricating Oil ℓ 11 ℓ, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 863
Pressure Drop mAq 3.4
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 1,075
Pressure Drop mAq 3.7
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 101.4 usRT
• Model : 13S010UR (101.4 usRT) • Dimension(Length x Width x Height)
- 3,350 x 950 x 2,120 mm
• Net Weight : 2,410 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 306.500
usRT 101.4
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 87.0
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-353 / Refcomp
Nominal Output x Q’ty kW 90 x 1
Starting Method - Y - △
Lubricating Oil ℓ 15 ℓ, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,022
Pressure Drop mAq 4.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 1,271
Pressure Drop mAq 4.5
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 125
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 125.7 usRT
• Model : 13S013UR (125.7 usRT) • Dimension(Length x Width x Height)
- 3,350 x 950 x 2,250 mm
• Net Weight : 2,670kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 380,080
usRT 125.7
Power
Main Supply - 3Ph x AC 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 108
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-463 / Refcomp
Nominal Output x Q’ty kW 120 x 1
Starting Method - Y - △
Lubricating Oil ℓ 16 ℓ, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,267
Pressure Drop mAq 3.9
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 1,577
Pressure Drop mAq 3.6
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 125
Cooling Water Pipe mm 150
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 171.1 usRT
• Model : 13S018UR (171.1 usRT) • Dimension(Length x Width x Height)
- 3,900 x 1,300 x 1,960 mm
• Net Weight : 3,710 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 517,330
usRT 171.1
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 148.0
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-305 / Refcomp
Nominal Output x Q’ty kW 75 x 1
Starting Method - Y - △
Lubricating Oil ℓ 11 ℓ x 2, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 1,724
Pressure Drop mAq 3.9
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 2,148
Pressure Drop mAq 3.6
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 150
Cooling Water Pipe mm 125 x 2
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 202.7 usRT
• Model : 13S020UR (202.7 usRT) • Dimension(Length x Width x Height)
- 3,950 x 1,300 x 2,100 mm
• Net Weight : 4,200 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 613,000
usRT 202.7
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 173.8
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-353 / Refcomp
Nominal Output x Q’ty kW 90 x 2
Starting Method - Y - △
Lubricating Oil ℓ 15 ℓ x 2, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 2,044
Pressure Drop mAq 4.1
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 2,542
Pressure Drop mAq 4.7
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 150
Cooling Water Pipe mm 125 x 2
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 252.1 usRT
• Model : 13S025UR (252.1 usRT) • Dimension(Length x Width x Height)
- 4,350 x 1,400 x 2,150 mm
• Net Weight : 4,850 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 762,280
usRT 252.1
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 216
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-463 / Refcomp
Nominal Output x Q’ty kW 120 x21
Starting Method - Y - △
Lubricating Oil ℓ 16 ℓ x 2, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 2,534
Pressure Drop mAq 3.5
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 3,153
Pressure Drop mAq 3.5
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 200
Cooling Water Pipe mm 150 x 2
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 295.7 usRT
• Model : 13S030UR (295.7 usRT) • Dimension(Length x Width x Height)
- 4,390 x 1,450 x 2,350 mm
• Net Weight : 5,500 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 894,250
usRT 295.7
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 254
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-553 / Refcomp
Nominal Output x Q’ty kW 150 x 2
Starting Method - Y - △
Lubricating Oil ℓ 19 ℓ x 2, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 2,980
Pressure Drop mAq 5.9
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 3,710
Pressure Drop mAq 4.7
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 200
Cooling Water Pipe mm 150 x 2
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
CLK Corporation
Water-Cooled Type Screw Chiller – 377.1 usRT
• Model : 13S038UR (377.1 usRT) • Dimension(Length x Width x Height)
- 3,800 x 2,600 x 2,260 mm
• Net Weight : 8,750 kg • Features
- Application of globally recognized high performance/high efficiency compressor and heat exchanger
- ‘ZERO’ ozone depletion by the environment friendly refrigerants
- Efficient operation enabled by Straight Stepless Capacity Control System
- Product safety/stability guaranteed by the reliable compressor and perfect protection devices
- Easy management/maintenance by a simple structure without pump oil
Specification
Cooling Capacity kcal/h 1,140,250
usRT 377.1
Power
Main Supply - 3Ph x 380V x 50Hz
Control Supply - 1Ph x AC 220 / 24V x 50Hz
Input kW 324
Compressor
Type - Semi Hermetic Screw Type
Model / Maker - SRC-S-463 / Refcomp
Nominal Output x Q’ty kW 120 x 3
Starting Method - Y - △
Lubricating Oil ℓ 16 ℓ x 3, CP-4214-320
Evaporator
Type - Shell & Tube Type
Chilled Water Inlet Temp. °C 12
Chilled Water Outlet Temp. °C 7
Chilled Water Flow Rate ℓ/min 3,800
Pressure Drop mAq 3.1
Condenser
Type - Shell & Tube Type
Cooling Water Inlet Temp °C 32
Cooling Water Outlet Temp °C 37
Cooling Water Flow Rate ℓ/min 4,730
Pressure Drop mAq 3.6
Refrigerant - R - 22
Refrigerant Control - Thermostatic Expansion Valve
Capacity Control Range % 25 ~ 100% ( Stepless)
Protection Device -
High/low Pressure Switch, Anti-Freezing Device,
Over Current Relay, Internal Thermostat,
Discharge Temp. Sensor, Safety Valve, Fusible Plug
Connection Chilled Water Pipe mm 250
Cooling Water Pipe mm 150 x 3
Note) 1. Fouling factor of water side: 0.0001m2h℃/kcal (Based on KS B 6275) 2. Electric power input is based on standard operation condition. If the operation condition is changed then the power consumption will be changed. The capacity of transformer and other electric equipment must be 130% higher than the standard power consumption. 3. Specifications are subject to change.
top related