Transcript
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 1/19
A Subject Seminar on
GEAR Prepared By:
Dhruv Upadhyay10EE57
Guided By:
A.B.SOLANKI. Sir
DJMIT MOGAR ANAND
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 2/19
Abstract
Power transmission is the movement of energy from its place of generation to alocation where it is applied to performing
usef ul work. A gear is a component within a
transmission device that transmitsrotational force to another gear or device .
Gear is very important drive in mechanicalpower transmission. Gear drive is positivedrive.
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 3/19
Contents Pages
1. Introduction
2. Nomenclature
3.
Types of G
ears4. Spur Gears
5. Helical Gears
6. Bevel gears
7. Worm and worm wheel
8. Rack & Pinion
9. Reference
10. Conclusion
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 4/19
Introduction
A gear is a toothed wheel with the teeth cut onthe periphery of a cylinder or a cone. It ismounted on the shafts with key. Gear drives is avery important drive in mechanical power
transmiss
ion. The rotat
ing of one gear w
ill ca
userotating of other in the opposite direction. Gear
drive is used to transmit power between shaftsthat are parallel, intersecting or neither parallelnor intersecting. It is transmitted the power whenthe axis of the shafts are not only parallel, but
even when non-parallel, intersecting and co-planer or non-co-planer. It is not suitable forshafts having centre distance.
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 5/19
NOMENCLATURE OF SPUR
GEARS
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 6/19
NOMENCLATURE«.
Pitch surface: The surface of the imaginary rolling cylinder (cone, etc.) that the toothed gear may be considered to replace.
Pitch circle: A right section of the pitch surface.
Addendum circle: A circle bounding the ends of the teeth, in
a right section of the gear. Root (or dedendum) circle: The circle bounding the spaces
between the teeth, in a right section of the gear.
Addendum: The radial distance between the pitch circle andthe addendum circle.
Dedendum: The radial distance between the pitch circle andthe root circle.
Clearance: The difference between the dedendum of one gear and the addendum of the mating gear.
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 7/19
NOMENCLATURE«.
Face of a tooth: That part of the tooth surface lying outsidethe pitch surface.
Flank of a tooth: The part of the tooth surface lying inside the pitch surface.
Circular thickness (also called the tooth thickness): Thethickness of the tooth measured on the pitch circle. It is thelength of an arc and not the length of a straight line.
Tooth space: pitch diameter The distance between adjacentteeth measured on the pitch circle.
Backlash: The difference between the circle thickness of onegear and the tooth space of the mating gear.
Circular pitch (Pc) : The width of a tooth and a space,measured on the pitch circle.
N
D P c
T
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 8/19
NOMENCLATURE«.
Diametral pitch (Pd): The number of teeth of a gear unit pitchdiameter. The diametral pitch is, by definition, the number of teeth divided by the pitch diameter. That is,
WherePd = diametral pitch
N = number of teeth
D = pitch diameter
Module (m): Pitch diameter divided by number of teeth. The pitch diameter is usually specified in inches or millimeters; inthe former case the module is the inverse of diametral pitch.
m = D/N
D
N P d !
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 9/19
Type of Gears
Spurs
Helical
Bevel
Worm and Worm Gears
Rack and pinion
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 10/19
Spur Gears
Are used in transmitting torque between parallel shafts
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 11/19
SPUR GEAR
Teeth is parallel toaxis of rotation
Transmit power from
one shaft to anotherparallel shaft
Used in Electricscrewdriver,
oscillating sprinkler,windup alarm clock,washing machine andclothes dryer
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 12/19
Helical Gears
Are used in transmitting torques between parallel or non
parallel shafts, they are not as noisy as spur gears
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 13/19
Bevel Gears
Are used to transmitrotary motion betweenintersecting shafts
Teeth are formed on conical
surfaces, the teeth could be
straight or spiral.
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 14/19
WORM AND WORM GEAR
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 15/19
WORM AND WORM GEAR
Worm gears are used when large gearreductions are needed. It is common forworm gears to have reductions of 20:1,
and even up to 300:1 or greater Worm gears are used widely in material
handling and transportation machinery,machine tools, automobiles etc
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 16/19
Rack and pinion
Rack and piniongears are used toconvert rotation (From
the pinion) into linearmotion (of the rack)
A perfect example of this is the steeringsystem on many cars
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 17/19
R eference
www.google.com
www.scribd.com
An text book of ³ELEMENTS OFMECHANICAL ENGINEERING´ by S. M.Bhatt , H. G. Katariya , J. P. Hadiya
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 18/19
CONCLUSION
From the above presentation we come to know the
importance of gear and where it is used.Gear is very
important in any machine and its main function of gear is to
for power transmission.
8/8/2019 Dhruv 10ee57
http://slidepdf.com/reader/full/dhruv-10ee57 19/19
top related