Chapter 10

Chapter 10

States of Matter

Section 1: The Kinetic-Molecular Theory of Matter

• Based on the idea that particles of matter are always in motion.

• Can be used to explain the properties of solids, liquids, and gases in terms of the energy of particles and the forces that act between them.

The Kinetic-Molecular Theory of Gases

• The theory provides an understanding of the behavior of ideal gas molecules and the physical properties.

• Ideal Gas- a hypothetical gas that perfectly fits all the assumptions of the kinetic-molecular theory.

The Kinetic-Molecular Theory of Gases

1. Gases consist of large numbers of tine particles that are far apart relative to their size– Gases are much farther apart than molecules of

liquids or solids– Most of the volume occupied by a gas is empty

space– Gases have lower density than liquids and solids– They are easily compressed

The Kinetic-Molecular Theory of Gases

2. Collisions between gas particles and between particles and container walls are elastic collisions (no loss of total kinetic energy as long as the temperature is constant).

– Kinetic energy is transferred between two particles during collisions.

The Kinetic-Molecular Theory of Gases

3. Gas particles are in continuous, rapid, random motion. They therefore possess kinetic energy, which is energy of motion.

4. There are no forces of attraction between gas particles, except near the temperature at which the gas condenses and becomes a liquid.

5. The temperature of a gas depend on the average kinetic energy of the particles of the gas. – Energy increases as temperature increases– Energy decreases as temperature decreases

Continued• Remember the Kinetic-Molecular Theory

only applies to IDEAL GASES• They are not found in nature; however,

there are many gases that behave nearly ideally

Expansion• Gases do not have a definite shape or

volume. They fill the container.• If a gas is transferred from a 2-L container

to a 3-L container, the gases will expand to fill the entire 3-L container.

Fluidity• Gas particles glide easily past one

another. • This ability to flow causes gases to behave

as liquids do; therefore, liquids and gases can be referred to fluids.

Low Density• The particles are so much farther apart in

the gas state causing low density.

Compressibility• During compression, the gas particles are

pushed closer together. The volume can be greatly decreased.

Diffusion and Effusion• Gases spread out and mix with one another,

even without being stirred (the air: not just oxygen)

• Diffusion-spontaneous mixing of two substances caused by their random motion (being able to smell perfume in the air after someone sprayed it)

• Effusion- process by which gas particles pass through a tiny opening (smelling perfume when inside a balloon)

Real Gases vs Ideal Behavior• A real gas is a gas that does not behave

completely according to the assumptions of the kinetic-molecular theory. – Noble gases and nonpolar gases react more

the ideal gases

Section 2: Liquids• Yes, I know it sounds crazy, but liquids are

the least common state of matter in the UNIVERSE. (On Earth they are extremely common)

• This is due to the fact that liquids only exist at a very small range of temperatures

Properties of Liquids and the Kinetic-Molecular Theory

• Definite volume and takes the shape of the container.

• Liquid particles are in constant motion. • They are closer together causing them not to

be able to move as fast as the gas particles. (more attractive forces)

• Fluids(liquids & gases)-a substance that can flow and therefore take the shape of the container

Properties of Liquids and the Kinetic-Molecular Theory

• Most liquids naturally flow downhill because of gravity (waterfalls)

• Some liquids can flow in other directions.– Liquid helium near absolute zero has the

unusual property of being able to flow uphill.

Relatively High Density• Most substances are hundreds of times

denser in the liquid state than gas state• The higher the density, the closer the

arrangement of particles (higher the attraction).

• Most substances are only about 10% less dense as a liquid than a solid.– Water is one of the few substances that

becomes less dense as a solid.

Density Column• The most dense on the bottom.• The least dense on the top

Relative Incompressibility• Liquids cannot be compressed very much

at all due to the closeness of particles.

Ability to Diffuse• Liquids can diffuse (food coloring in water)• Diffusion happens much slower in liquids• Higher temps increase rate of diffusion• Lower temps decreases the rate of

diffusion

• ***Again Kinetic Energy-energy of motion

Surface Tension• A force that tends to pull adjacent parts of

a liquid’s surface together, thereby decreasing surface area to the smallest possible size.

• Higher attraction, higher surface tension• Water is higher than most liquids

**Surface tension-Penny

Surface Tension• Capillary action- the attraction of the

surface of a liquid to the surface of a solid– Paper Chromatography (Y’all did this in the 8th

grade. You used markers and you made dots on a piece of chromatography paper. Then put the edge of paper in the water. It separated the ink into the colors it was made of.)

– Plant/Tree roots getting water– The meniscus to form on a graduation cylinder

Evaporation and Boiling• Vaporization- the process by which a liquid or

solid changes to a gas• Boiling – change of liquid to bubbles of vapor

which then go to a gas.• Evaporation- the process by which particles

escape from the surface of a nonboiling liquid and enter the gas state.– All water that falls to the Earth (rain, sleet, snow, etc..)

if from the evaporation of fresh water from the ocean– Evaporation of perspiration keeps you cool.

Formation of Solids• When liquids cool enough for the attractive

forces to become great enough to have order. This reduces the kinetic energy.

• Freezing (solidification) - physical change of a liquid to a solid by the removal of heat.– Liquid water to ice– Liquid Wax (burning a candle) to paraffin

Section 3: Solids• Definite shape and volume• Particles are packed more closely than in

liquids (stronger forces)• Constant motion (just can move very

much)

Crystalline solids & Amorphous solids

• Crystalline- consist of crystals (diamonds, quartz, salt, ice)

• Amorphous- particles are randomly arranged (plastics, glass)

Definite Melting Point• Melting Point- the temperature at which a

solids changes to a liquids by the addition of heat.

• The melting point (solid to liquid) and the freezing point (liquid to solid) are the same temperature.

• This point can be used to identify substances.

High Density & Incompressibility

• In general substances are most dense in the solid state (exception: water)

• Higher density is due to closeness of particles

• Considered to incompressible

Low Rate of Diffusion• Diffusion can occur. However, it is

extremely slow

Section 4: Changes of State• Phase (or state)- any part of a system that

has uniform composition and properties.• Look at Table 2 on page 342

Equilibrium• Dynamic condition in which two opposing

changes occur at equal rates in a closed system.

• Condensation is happing at the same rate as evaporation therefore no mass change

Volatile Liquids• Liquids that evaporate readily due to weak

forces of attraction.– Ether– Rubbing alcohol

Nonvolatile liquids do not evaporate readily-water

Boiling• Conversion of a liquid to a vapor within the liquid

as well as at its surface.• Boiling point- the temperature at which this

conversion happens• The lower the pressure, the lower the boiling point

– This is why on the back of a cake mix it says if you are at a certain elevation, then you need to bake it at a lower temp.

– Pressure cookers increase pressure; therefore they boil and cook quicker

Energy and Boiling• Energy must be added continuously in

order to keep a liquid boiling• The temperature at the boiling point

remains constant despite the continuous addition of energy. The temp will change when the conversion has finished.

Molar Enthalpy of Vaporization

• The amount of energy as heat that is needed to vaporize one mole of liquid at the liquid’s boiling point at constant temperature. – The stronger the attraction of molecules the

more energy will be needed to break those bonds.

– Water has an extremely high molar enthalpy. This is why it is such a great coolant.

Freezing and Melting• Freezing involves a loss of energy• Melting involves absorbing (gaining

energy)• Molar enthalpy of fusion- the amount of

energy as heat required to melt on mole of slid at the solid’s melting point

Sublimation and Deposition• Sublimation- solid going to gas phase,

skipping the liquid phase– Dry ice– Iodine– Ice can but slowly (snow disappearing even

when it has gotten above freezing)• Deposition- gas to solid phase, skipping

the liquid phase– Frost

Phase Diagrams: Look on page 347 in your book

• Triple point- indicates the temp and pressure in which a solid, liquid, and gas can all be present

• Critical point- critical temp and pressure• Critical temp- above this temp the substance

can’t exist as a liquid regardless of pressure• Critical pressure- the lowest pressure at

which the substance can exist as a liquid at the critical temp.

Section 5: Water• On Earth, water is the most abundant

liquid• Makes up about 75 % of Earth’s surface• Water is about 70-90% of all living things

mass

Physical Properties of Water• At room temperature: it is a liquid, transparent,

odorless, tasteless, almost colorless• Freezes and Melts at 0oC• Water expands as it freezes• Solid water is less dense than liquid water• Boils at 100oC• Molar enthalpy of fusion is 6.009 kJ/mol• Molar enthalpy of vaporization is 40.79 kJ/mol

Example• What quantity of energy is released when

506 grams of liquid water freezes?

• What mass of steam is required to release 4.97 x 105 kJ of energy on condensation?