Ca Ex S1 M05 Osi Network Layer

Post on 21-Oct-2014

3241 Views

Category:

Technology

0 Downloads

Preview:

Click to see full reader

DESCRIPTION

 

Transcript

CCNA – Semester1

Chapter 5 - OSI Network Layer

CCNA Exploration version 4.0

Objectives

• Identify the role of the Network Layer, as it describes

communication from one end device to another end

device

• Examine the most common Network Layer protocol,

Internet Protocol (IP), and its features for providing

connectionless and best-effort service

• Understand the principles used to guide the division or

grouping of devices into networks

• Understand the hierarchical addressing of devices and

how this allows communication between networks

• Understand the fundamentals of routes, next hop

addresses and packet forwarding to a destination

network

Introduction

• The protocols of the OSI model Network layer specify

addressing and processes that enable Transport layer data to

be packaged and transported. The Network layer encapsulation

allows its contents to be passed to the destination within a

network or on another network with minimum overhead.

IPv4

Network Layer – Communication from Host to

Host

• Layer 3 uses four basic processes:

– Addressing

– Encapsulation

– Routing: Intermediary devices that connect the networks

are called routers. The role of the router is to select paths

for and direct packets toward their destination. This

process is known as routing.

– Decapsulation

Network Layer – Communication from Host

to Host

Network Layer – Communication from Host

to Host

Network Layer Protocols

• Protocols implemented at the Network

layer that carry user data include:

– Internet Protocol version 4 (IPv4)

– Internet Protocol version 6 (IPv6)

– Novell Internetwork Packet

Exchange (IPX)

– AppleTalk

– Connectionless Network Service

(CLNS/DECNet)

The IPv4 Protocol – Example Network Layer

Protocol

• The Internet Protocol was designed as a protocol with low overhead. It

provides only the functions that are necessary to deliver a packet from

a source to a destination over an interconnected system of networks.

The protocol was not designed to track and manage the flow of

packets. These functions are performed by other protocols in other

layers. Basic characteristics:

The IPv4 Protocol – Connectionless

The IPv4 Protocol – Best Effort

• Since protocols at other layers can manage reliability, IP is

allowed to function very efficiently at the Network layer.

Best Effort Service (unreliable)

• Describe the implications for the use of the IP protocol as it is considered an unreliable protocol

• Unreliable means simply that IP does not have the capability to manage, and recover from, undelivered or corrupt packets.

The IPv4 Protocol – Media Independent

• One major characteristic of the media that the Network layer considers: the maximum size of PDU that each medium can transport: the Maximum Transmission Unit (MTU). Part of the control communication between the Data Link layer and the Network layer is the establishment of a maximum size for the packet.

• IPv4 and IPv6 operate independently of the media that carry the data at lower layers of the protocol stack

Packaging the Transport Layer PDU

• The process of encapsulating data by layer enables the services at the

different layers to develop and scale without affecting other layers.

• Routers can implement these different Network layer protocols to operate

concurrently over a network to and from the same or different hosts. The

routing performed by these intermediary devices only considers the

contents of the packet header that encapsulates the segment.

IPv4 Packet Header

Network Layer Fields

• 4 bits

• Indicates version of IP used

• IPv4: 0100; IPv6: 0110

Network Layer Fields

• 4 bits

• Indicates datagram header length in 32 bit words

Network Layer Fields

• 8 bits

• Specifies the level of importance that has been

assigned by upper-layer protocol

Network Layer Fields

• 16 bits

• Specifies the length of the entire packet in bytes,

including data and header

Network Layer Fields

• 16 bits

• Identifies the current datagram

Network Layer Fields

• 3 bits

• The second bit specifies if the packet can be fragmented; the last

bit specifying whether the packet is the last fragment in a series

of fragmented packets.

Network Layer Fields

• 13 bits

• Used to help piece together datagram

fragments

Network Layer Fields

• 8 bits

• Specifies the number of hops a packet may travel. This

number is decreased by one as the packet travels

through a router

Network Layer Fields

• 8 bits

• Indicates which upper-layer protocol, such as TCP(6) or

UDP(17), receives incoming packets after IP

processing has been completed

Network Layer Fields

• 16 bits

• Helps ensure IP header integrity

• Not caculated for the encapsulation data

Network Layer Fields

• 32 bits

• Specifies the sending node IP address

Network Layer Fields

• 32 bits

• Specifies the receiving node IP address

Network Layer Fields

• Variable length

• Allows IP to support various options, such as security

Network Layer Fields

• Variable length

• Extra zeros are added to this field to ensure that the IP

header is always a multiple of 32 bits.

Network Layer Fields

• Variable length up to 64 KB

• Contains upper-layer information

Networks –

Dividing Hosts into Groups

Separating Hosts into Common Groups

• Networks can be grouped based on factors that include:

– Geographic location

– Purpose

– OwnershipGeographic

Separating Hosts into Common Groups

Purpose: Users who have similar tasks typically use

common software, common tools, and have common

traffic patterns.

Separating Hosts into Common Groups

Purpose

Separating Hosts into Common Groups

Ownership: Using an organizational (company,

department) basis for creating networks assists in

controlling access to the devices and data as well as

the administration of the networks.

Separating Hosts into Common Groups

Ownership

Why separate hosts into networks

Common issues with large networks are: Performance

degradation, Security issues, Address Management

• Improving Performance:

Why separate hosts into networks

• Increase network security

Why separate hosts into networks

• Address management: To expect each host to know the

address of every other host would impose a processing

burden on these network devices that would severely

degrade their performance.

Why separate hosts into networks

• Hierarchical addressing: solves the problem of devices

communicating across networks of networks

Dividing the networks - Networks from networks

• If a large network has to be divided, additional layers of

addressing can be created. Using hierarchical addressing

means that the higher levels of the address are retained; with a

subnetwork level and then the host level.

Routing –

How Our Data Packets are Handled

Routing Protocols

• Routing is an OSI Layer 3

function. It is a hierarchical

scheme and allows individual

addresses to be group together.

• Routing is the process of finding

the most efficient path from one

device to another.

Routing Protocols

• Provides processes for sharing route information

• Allows routers to communicate with other routers to update and maintain

the routing tables

• Examples: Routing Information Protocol (RIP), Interior Gateway Routing

Protocol (IGRP), Open Shortest Path First (OSPF), Border Gateway

Protocol (BGP), and Enhanced IGRP (EIGRP)

Supporting communication outside our network

This is called the next-hop address. If a route is available to the router, the router will forward the packet to the next-hop router that offers a path to the destination network.

• To communicate with a device on another network, a host

uses the address of this gateway, or default gateway, to

forward a packet outside the local network.

• The router also needs a route that defines where to forward

the packet next.

Fundamentals of Routes, Next Hop Addresses and Packet

Forwarding

• If the destination host is in the same network as the source host, the packet is delivered between the two hosts on the local media without the need for a router.

• If the destination host and source host are not in the same network, the packet may be carrying a Transport layer PDU across many networks and through many routers.

IP Packet – Carrying Data End-to-End

IP Packet – Carrying Data End-to-End

IP Packet – Carrying Data End-to-End

IP Packet – Carrying Data End-to-End

IP Packet – Carrying Data End-to-End

A gateway – the way out of our network

A gateway – the way out of our network

A gateway – the way out of our network

• A router makes a forwarding decision for each packet that arrives at the

gateway interface. This forwarding process is referred to as routing. To

forward a packet to a destination network, the router requires a route to

that network. If a route to a destination network does not exist, the packet

cannot be forwarded.

Routing table

• The routing table stores information about connected and

remote networks. Routes in a routing table have three main

features:

– Destination network

– Next-hop

– Metric

A Route – The Path to a Network

Host Routing Table

• A host creates the routes used to forward the packets it originates. These routes are derived from the connected network and the configuration of the default gateway.

• Hosts automatically add all connected networks to the routes. These routes for the local networks allow packets to be delivered to hosts that are connected to these networks.

Route print

Routing table entries

Routing table entries

Default route

• A router can be configured to have a default route. A default route

is a route that will match all destination networks. In IPv4

networks, the address 0.0.0.0 is used for this purpose. The

default route is used to forward packets for which there is no entry

in the routing table for the destination network. Packets with a

destination network address that does not match a more specific

route in the routing table are forwarded to the next-hop router

associated with the default route.

Packet forwarding

• Routing is done packet-by-packet and hop-by-hop. Each

packet is treated independently in each router along the path.

• The router will do one of three things with the packet: Forward

it to the next-hop router; Forward it to the destination host;

Drop it.

Packet forwarding

• If the routing table does not contain a more specific route entry for an

arriving packet, the packet is forwarded to the interface indicated by a

default route, if one exists. The default route is also known as the

Gateway of Last Resort.

Packet forwarding

Routing Processes –

How Routes are Learned

Routing protocol – Sharing the route

• Routing protocols: static and dynamic routes

Static Routing

• Static route: routes to remote networks with the

associated next hops can be manually configured on the

router. A default route can also be statically configured.

Dynamic Routing

• Routing protocols are the set of rules by which routers

dynamically share their routing information.

Routing protocol

• Provides processes for sharing route information

• Allows routers to communicate with other routers to update and

maintain the routing tables

• Examples: Routing Information Protocol (RIP), Interior Gateway

Routing Protocol (IGRP), Open Shortest Path First (OSPF), Border

Gateway Protocol (BGP), and Enhanced IGRP (EIGRP)

IGP and EGP

• Autonomous system is a network or set of networks under common

administrative control. An autonomous system consists of routers that present

a consistent view of routing to the external world.

• Interior Gateway Protocols (IGP): route data within an autonomous system. Eg:

RIP and RIPv2; IGRP; EIGRP; OSPF; IS-IS;

• Exterior Gateway Protocols (EGP): route data between autonomous systems.

Eg: BGP

Link state and Distance Vector

• The distance-vector routing approach determines the

distance and direction, vector, to any link in the

internetwork. Routers using distance-vector algorithms send

all or part of their routing table entries to adjacent routers on

a periodic basis. This happens even if there are no changes

in the network. Eg: RIP, IGRP, EIGRP

• Link state routing protocols send periodic update at longer

time interval (30’), Flood update only when there is a

change in topology. Link state use their database to create

routing table. Eg: OSPF, IS-IS

Dynamic Routing: Example 5.4.3.2

Summary

top related