Transcript
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV.
8/3
/201
2 IN
ST-A
SWC
INSTALLATION INSTRUCTIONS FOR PART ASWC
IGNI
TION
TERM
INAL
S
WIR
ECU
TTERM3.
5
M2.
6M
3M
5
M4
ISO
62.
51.
5
KIT FEATURES
• OneInterfacedoesitall-Noadditionalinterfacesneeded• Designedtobecompatiblewithallmajorradiobrands• Autodetectsvehicletype,radioconnection,andpresetscontrols• Canbemanuallyprogrammedformostvehicles• Memoryretainssettingsevenafterbatterydisconnection
orinterfaceremoval• Connectionplacementsareallorganizedbehindtheradio• USBupdatable
INTERFACE COMPONENTS
•ASWCInterface•12-pinharnesswithmale3.5mmconnector•Female3.5mmconnectorwithBrownandBrown/Whitewires
•12k-ohmresistor
TOOLS REQUIRED
•Cuttingtool•Crimpingtool•Tape•Connectors(example:butt-connectors,bellcaps,etc.)
Axxess Steering Wheel Control Interface Installation Manual
ASWC
US.PAT.NOS.8014920and8214105
Table of Contents
Preface .............................................................................................. 3
Overview– IntroductiontotheASWCInterfaceandWiringHarness .................4-5
ASWC– Section1:Installation ....................................................................6-7
– Section2:Programming ................................................................8-9
– Section3:Troublshooting
AutoDetectMode ...................................................................... 10
ManualProgramming ...........................................................10-13
ChangingRadioType ............................................................13-14
ManualRadioTypeProgramming .........................................14-15
– Section4:Remapping
RemappingSWCButtons ........................................................... 16
ResettingOriginalSWCSettings ................................................ 17
ASWC Ledgend– VehicleLEDFeedback ..................................................................... 18
– RadioLEDFeedback ..................................................................18-19
– ButtonAssignment(remapping/manualprograming) ....................... 19
Caution: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the aftermarket radio.
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 AxxESSINTERfACE.COM
What you need to know before you begin
1) Knowthecorrectyear,make,andmodelofyourvehicle.
2) BesurethattheradioyouareinstallingiscompatiblewiththeAxxesssteeringwheelcontrol(ASWC)interface(refertotheaftermarketradioowner’smanual).
3) GototheAxxesswebsite(www.axxessinterface.com)andclickon“SteeringWheelControl”(SWC),whichislocatedontherightsideofthescreen.Onceyouputyourvehicleinformationinandhit“Submit”,anewpagewillcomeupwithtwosourcesofinformation.One,adocumentinPDFformlocatedbelowinthe“Documents”tab.Andsecond,detailedinformationonwhichcolor(s)thesteeringwheelcontrolwireswillbeinyourvehicleunderthe“VehicleInformation”tab.PrintthePDFdocumentsoyouhaveitinthevehicleduringtheinstallasitisthebestandeasiestsourceofinformation.
Note: Even though we have done extensive research and testing (to verify that the steering wheel control wire colors of the vehicle(s) we list are correct) it is still your responsibility to verify the steering wheel control wires with a multimeter. If you find a discrepancy please notify our Tech Department at 1-800-253-TECH. Please be in the vehicle when you call, with access to the interface and vehicle wiring.
Preface
3
4
Introduction to the ASWC Interfaceand Wiring Harness
OnthetopoftheASWCinterfacetherearethreepointsofinterest:
1) TheProgramming LED–Flashesrapidlywheninautodetectmode,flashesslowlyinmanualprogrammingmode.
2) TheReset Button–Holddownbuttonfor3secondstostartautodetectmode;holddownlongerthen10secondstostartmanualprogrammingmode.
3) TheSlide Cover(USBPortCover)–OpenthisuptorevealtheUSBupdateport.UsingtheUSB-CABupdatecableandtheAxxesswebsiteyoucanmakesureyoualwayshavethelatestupdatedinventory.
Overview
USBPortCover ResetButton ProgrammingLED
5
Overview
Pin-1 PinkPin-2 White/GreenPin-3 Yellow/GreenPin-4 Green/OrangePin-5 Gray/RedPin-6 BlackPin-7 Blue/Pink
Pin-8 Black/GreenPin-9 Red(tip of 3.5mm
connector)
Pin-10 White (ring of 3.5mm connector)
Pin-11 Gray/Blue Pin-12 Red
BelowarethewirecolorsfortheASWC.PleasevisittheAxxesswebsiteatwww.axxessinterface.comfordetailedinformationonyourspecificvehicleandforwhatcolorwire(s)tousewiththeASWCinterface.
6
Section 1: Installation
OnceyouhavecollectedorprintedouttheinformationsheetonyourparticularvehiclefromtheAxxesswebsite(www.axxessinterface.com)you’rereadytoinstalltheASWC.
Installing the ASWC
1) ConnecttheBlackwireoftheASWCtoground.Youmayusethesamegroundingpointastheaftermarketradio.
2) ConnecttheRedwireoftheASWCtoa12-voltaccessorywire,onethatturns“On”and“Off”withtheignitionkey.
3) LocatethecorrectSWCwire(s)inthevehicle’sradioprimaryorsecondaryharnessasdescribedinthevehicleinformationsheetfoundontheAxxesswebsite.Connectthecorrectwirecolor(s)fromtheASWCtothesteeringwheelcontrolwire(s)inthevehicle.
Note: Metra recommends that the wire(s) are soldered for the best and most secure connection. T-Taps or scotch locks are not recommended due to the higher chance of an intermitted connection or change in resistive values.
7
Section 1: Installation
4) IfyouareusinganEclipse,Kenwood,MetraOE,oranewerJVCradio,plugtheincludedfemale3.5mmconnectorwiththeBrownandBrown/Whitewiresintothemale3.5mmconnectoroftheASWCharness.
• For Kenwood and select JVC: ConnecttheSWCwire(normallyBlue/Yellow)totheBrownwireoftheASWC.IsolateandtapetheBrown/Whitewire,itwillnotbeused.
Note: Some newer Kenwood radios will auto detect as a JVC. If this is the case, you can use a 12k-ohm resistor (included) in line between the Blue/Yellow and Brown wire of the female 3.5mm jack during programming only. Or you can manually set the radio type which is in the radio programming section of this manual.
• For Eclipse:ConnecttheEclipseSWCwires(normallyBrown andBrown/Black)totheBrownandBrown/WhitewiresoftheASWC. BrowngoestoBrownandBrown/WhitegoestoBrown/Black.Sometimesthisisreversed,reversethewiresifneeded.
• For Metra OE: ConnecttheSWCKey1wire(Gray)totheBrown wireoftheASWC.
5) Forallotherradios,pluginthemale3.5mmconnectoroftheASWCintothebackoftheaftermarketradio,designatedforanexternalSWCcontrolinterface.Ifindoubtwherethe3.5mmconnectoroftheASWCgoespleaserefertotheaftermarketradiomanual.Onceallconnectionshavebeenmade,plugintheaftermarketradioifnotdonealready.
8
TheASWCcanbeprogrammedintwoways.(1)ItcandoitbyitselfthroughAutoDetectMode,or(2)itcanbemanuallyprogrammedinnon-datavehicles.ItisstronglyrecommendtostartwiththeAutoDetectModefirst.
Auto Detect Mode: Overview
TheASWChastheabilitytoautodetectcertainvehiclesandtoknowwhataftermarketradioitisconnectedto.ThevehicleinfosheetfromtheAxxesswebsite(www.axxessinterface.com)willindicateifyourvehiclewilllikelybeautodetectedandwhataction,ifany,isrequiredbyyouforthisprocesstotakeplace.
FortheAutoDetectfeaturetoworkthereare3possibleactions,howeveronlyoneactionwillberequiredbyyoudependingonyourvehicle:
• Turntheignitiononandnootheractionisrequired.
• Turntheignitionon,pressandholdthe“VolumeUp”buttononthesteeringwheel.
--- Or ---
• Turntheignitionon,pressandreleasethe“VolumeUp”buttonrepeatedlyonthesteeringwheel.
Asstatedbefore,onlyoneoftheseactionswillneedtobedonedependingonyourvehiclefortheAutoDetectfeaturetowork.PleaserefertothevehicleinfosheetprovidedontheAxxesswebsite.
Auto Detect Mode: Steps
1) Completeconnectionstothevehicleandtheaftermarketradio.
IfthisisthefirsttimetheASWCisbeinginstalledinavehicle:
Section 2: Programming
9
2) Turntheignitionon;theLEDwillstartflashingrapidlywhichmeanstheASWCislookingforthevehicleandtheradio.Gotostep4.
--- Or ---
IftheASWCwasinstalledinavehiclepreviously:
2) Turntheignitionon,theLEDwillflashonce,thengoout.
3) Holddowntheresetbuttonfor3secondsandthenreleaseit.
4) Performactionrequiredforyourparticularvehicleasnotedinthevehicleinfosheet.
5) AfteracoupleofsecondstheLEDshouldstopflashingandnotlightupfor2seconds.Atthispointdonotpushanybuttons.
6) Afterthe2secondstherewillbeaseriesof7flashes,someshortandsomelong.
7) TheLEDwillpauseforanother2secondsthenflashupto11times(refertoASWCledgend).
8) Thisistheendoftheautodetectionstage.IftheASWCdetectedthevehicleandtheradiosuccessfullytheLEDwilllightupsolidred.
9) ForvehicleswithOEBluetoothbuttonspleasepress“Hangup”or“Pickup”onyoursteeringwheelcontrolaftertheLEDontheASWCgoessolid.IftheOEBluetoothbuttonsareabletobeused,theLEDwillgooutafter3seconds.YourOEBluetoothbuttonsarenowprogrammedtoyouraftermarketradiosBluetoothbuttons(aftermarketradiomusthaveBluetoothcapabilities).
Tip: If the LED does not light up solid red refer to the troubleshooting section.
10)Makesurethesteeringwheelcontrolbuttonsfunctioncorrectlyinthevehicleandenjoy.
Section 2: Programming
10
Auto Detect Mode
SoyoutriedtheautodetectfeatureandattheendtheLEDdidnotstaysolidred.Insteaditstartedflashing,meaningthattheASWCdidnotdetectthevehicle.
Followthesestepstodeterminewhatmayhavehappened:
1) Verifythatyouhave12-voltaccessoryandagoodgroundtotheASWC.Sometimesthefactorygroundisnotsufficient,achassisgroundishighlyrecommended.IfyourvehiclehasaSWCreferencegroundwire,chassisgroundthataswell,alongwithyouraftermarketradio.
2) Validateusingthevehicleinformationsheet(Axxesswebsite)thatthecorrectsteeringwheelcontrolwire(s),inthevehicle,wereconnectedtothecorrectwire(s)totheASWC.
3) Confirmthatthe3.5mmconnectorisconnectedtoyourradiosecurelyandinthecorrectlocation.
4) Ifusingthefemale3.5mmconnectorinEclipse,Kenwood,selectJVC,orMetraOEradiosverifythattheradio’sSWCwireisconnectedtothecorrectwiretotheASWC.
Manual Programming Auto Detect Mode
IfyourvehicleisnotlistedforautodetectionbytheASWContheAxxesswebsite,www.axxessinterface.com,youcanmanuallyprogramanon-datavehiclebythefollowingsteps(haveASWClegendavailable).
Section 3: Troubleshooting
11
Note: Not every radio will have all the possible SWC commands on the steering wheel. Aftermarket radios that do not have Bluetooth will not recognize the PTT (Push To Talk) or “On/Off Hook” commands; however those buttons can be manually programmed to do other commands in some cases. Please refer to the radio owner’s manual or wireless remote for specific commands that the radio will recognize.
1) Completeconnectionstothevehicleandtotheaftermarketradio,makesurethe3.5mmconnectorisconnected.
IfthisisthefirsttimetheASWCisbeinginstalledinavehicle:
2) Turntheignitionon;theLEDwillstartflashingrapidly.
3) After10secondstheASWCwillgointotheLEDfeedbackmode.AftertheseriesofLEDflashestheLEDwillstayinaslowconstantflashstate.Gotostep4.
--- Or ---
IftheASWChasbeeninavehiclebefore:
2) Pressandholdtheresetbuttondownformorethen10seconds.
3) Afterthe10secondstheLEDwillbeginaslowconstantflash.
4) Atthispointpressandholdthe“VolumeUp”buttononthesteeringwheelfor7secondsuntiltheLEDgoessolidred.Nowreleasethe“VolumeUp”buttonandtheLEDgoes“Off”.“VolumeUp”hasnowbeenprogrammed.
Section 3: Troubleshooting
12
5) Nowpressandholdthe“VolumeDown”buttonuntiltheLEDgoessolidred.ReleasethebuttonandtheLEDwillturn“Off”.The“VolumeDown”hasnowbeenprogrammed.
6) AtthispointgototheASWCLegendButtonAssignment(remapping/manualprogramming)section,page19,andcontinuewith“SeekUp/Next”button.
7) Youcanendthishalfoftheprogrammingin2ways:
(1) Afterthelastbuttononyoursteeringwheelhasbeenprogrammed(youdonothavetogothroughthewholelist)holddownthe“VolumeUp”buttonforatleast 10seconds.TheLEDwillgointoaslowconstantblinkmode.
--- Or ---
(2) Afterthe18thbuttonisprogrammedorskippedtheLEDwillgobacktotheslowconstantblinkmode.
Note: If at any time an error is made hold down the reset button on the ASWC for 10 or more seconds. This will restart the manual programming. Go back to Step 4 and start again.
8) Pressandholdthe“VolumeDown”buttonfor5secondstilltheLEDstartstoflashquickly.
9) Releasethe“VolumeDown”button.
10) After4secondsoftheLEDflashingquicklytheLEDwillgooutfor2seconds.
Section 3: Troubleshooting
13
11) ThentheLEDwillflash,upto11times,dependingonwhatradiotheASWCthinksit’sconnectedto.
12) Makesurethenumberofflashesmatchwhatradioyouhaveinstalled.RefertotheChangingRadioTypesection,pages13-14.
13) IftheLEDflashesmatchtheradiothenholddownthe“VolumeDown”buttonuntiltheLEDgoessolidred.
14)Programmingforthevehicleandtheradioisnowcomplete.Testoutthesteeringwheelcontrolfunctionstomakesureitworkscorrectly.
Changing Radio Type
IftheLEDflashesdonotmatchtheradioyouhaveconnected,youmustmanuallyprogramtheASWCtotellitwhatradioitisconnectedto.
1) Tomanuallyprogramtheaftermarketradio,pressandholdthe“VolumeDown”buttononthesteeringwheelcontroluntiltheLEDgoessolidred,thenrelease“VolumeDown”.
2) AtthispointEclipseisprogrammed.IfyouareusinganEclipseradiogotostep3.Ifyouareusingadifferentradiogotostep4.
3) Pressandhold“VolumeDown”for5seconds.TheLEDwillflashoncethengosolidredindicatingtheprogramminghasfinished.Goenjoyyourradio.
4) IfyouhaveadifferentradiothenEclipse,presstheVolumeUpbuttonagaintilltheLEDgoessolidred,thenrelease“VolumeUp”.YouhavenowprogrammedKenwood.
Section 3: Troubleshooting
14
5) Hereisthecharttoshowhowmanypressesofthe“VolumeUp”buttonisneededforwhichradioyouaretryingtoprogram:
6) Oncetheradiomanufacturerhasbeenselectedhold “VolumeDown”foratleast5seconds.TheLEDwillflashthenumberoftimeswhichradiowasselectedthentheLEDwillremainontoindicatetheASWChasfinishedprogramming.
Manual Radio Type Programming
Ifonlychangingtheradiotypeisneededthenfollowthisprocedurebelow.
1) Withinthefirst25secondsofturningthekeyon,pressandholdthecar’s“VolumeDown”button.
2) After15secondsofholding“VolumeDown”,theASWC’sredLEDwillgoon.
3) Releasethe“VolumeDown”andtheLEDwillgo“Off”.Wearenowinradioprogrammingmode.
Section 3: Troubleshooting
1 Eclipse2 Kenwood3 Clarion“Type1”4 SonyandDual5 JVC 6 PioneerandJensen
7 Alpine8 Visteon9 Valor10 Clarion“Type2”11 MetraOE
15
4) Pressandreleasethe“VolumeUp”buttonforthedesiredradionumber(pleaserefertotheASWClegend).ForeachpresstheredLED.Itwillgo“On”andthen“Off”whenreleasedforfeedback.
5) Whenthedesiredradiotypehasbeenreached,Pressthe“VolumeDown”button.
6) TheLEDwillgoonandwillremainon(approximately3seconds).The ASWC is internally computing and storing this new information.
7) TheLEDwillgo“Off”indicatingitiscompleted.
Note: If at any time the user fails to press any button for a period of 10 seconds or more, this programing mode will abort.
Section 3: Troubleshooting
16
Remapping the SWC (Steering Wheel Control) Buttons
OnceyouhavetheASWCprogrammedyoucanthenchangethesteeringwheelcontrolbuttonassignment(s).Suchas,programingthe“SeekUp”buttonasa“Mute”function.FollowthestepsbelowtoremaptheSWCbuttons:
1) IdeallyhavetheASWCvisible,soyoucanseetheLEDflashestoconfirmbuttonrecognition.
2) Turning“Off”theradioisrecommended.
3) Withinthefirst20secondsofturningtheignitionon,pressandholddownthe“VolumeUp”buttonforatleast20seconds.
4) TheLEDwilllightupsolidred.Release“VolumeUp”andtheLEDwillgoout.“VolumeUp”hasnowbeenprogrammed.
5) FollowthelistintheButtonAssignmentsection,page19,toreferencetheorderofwhatbuttonsneedtobepressedand/orhowtobypassabutton.
6) Afterthelastbuttonisprogrammedonyoursteeringwheel(youdonothavetogothroughthewholelist),holddownthe“VolumeUp”buttonforatleast10secondsthentheLEDwillgoout.
--- Or ---
Afterthe18thbuttonisprogrammedorskippedtheLEDwillgooutandtheremappingiscompleted.
Section 4: Remapping
17
Resetting Orginal SWC Settings
Ifforanyreasonafterremappingthesteeringwheelcontrolsyouwanttorevertbacktotheoriginalsteeringwheelcontrolsettings,followthesesteps:
1) Withinthefirst20secondsofturningtheignitionon.Pressandholddowntheoriginal“VolumeDown”button(notthe“VolumeDown”buttonyoujustremapped)foratleast25seconds.
2) TheLEDwillturnonthenreleasethe“VolumeDown”buttonandtheLEDwillturn“Off”.
3) Theoriginalsteeringwheelcontrolsettingswillberestored.
Section 4: Remapping
18
For A and B: Short flashesrepresentthesteeringwheelcontrolwire(s)thatarenotconnectedtothevehiclefromtheASWC.Long flashesrepresentwire(s)thatareconnectedtothevehicle.
A. Vehicle LED Feedback 1stLEDflashistheWhite/GreenwireontheASWC
2ndLEDflashistheOrange/GreenwireontheASWC
3rdLEDflashistheGreen/OrangewireontheASWC
4thLEDflashistheGray/RedwireontheASWC
5thLEDflashistheBlack/GreenwireontheASWC
6thLEDflashistheGray/BluewireontheASWC
7thLEDflashisthePinkwireontheASWC
B. Radio LED Feedback 1stLEDflashisforEclipse
2ndLEDflashisforKenwood
3rdLEDflashisforClarion(“Type”1)
4thLEDflashisforSonyandDual
5thLEDflashisforJVC
6thLEDflashisforPioneerandJensen
7thLEDflashisforAlpine*
8thLEDflashisforVisteon
9thLEDflashisforValor
10thLEDflashisforClarion(“Type”2)
11thLEDflashisforMetraOE
ASWC Ledgend
19
C. Button Assignment(remapping/manualprogramming)
ASWC Ledgend
1.VolumeUp
2.VolumeDown
3.SeekUp/Next
4.SeekDown/Prev
5.Source/Mode
6.Mute
7.PresetUp
8.PresetDown
9.Power
10.Band
11.Play/Enter
12.PTT(PushToTalk)
13.OnHook
14.OffHook
15.FanUp
16.FanDown
17.TempUp
18.TempDown
Note: Not all radios will have all of these commands. Please refer to the radio owner’s manual or contact the radio vendor directly for specific commands recognized by that particular radio.
If the next function on the list is not on the steering wheel press the “Volume Up” button for 1 second, until the LED comes on, then release the button. This tells the ASWC that the function is not available will move on to the next function.
*Note (section B): If the ASWC flashes 7 times and you do not have an Alpine radio connected to it that means that the ASWC did not see any radio connected. Verify the 3.5mm connector is connected to the SWC input on the radio.
INSTALLATION INSTRUCTIONS FOR PART ASWC
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 AxxESSINTERfACE.COM
REV.
8/3
/201
2 IN
ST-A
SWC
KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians
IMPORTANT WARNING
Thisproductincludesinstructionsforinstallationwhichmustbecarefullyfollowed.Theinstructionsarewordedinsuchamannertoassumethattheinstalleriscapableofcompletingthesetypeofelectronicinstallations.Ifyouareunclearastowhatyouareinstructedtodoorbelievethatyoudonotunderstandtheinstructionssoastoproperlyandsafelycompletetheinstallationyou should consult a technician who does have this knowledge and understanding.
Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or to safety systems on the vehicle. Interference with certain safety systems could cause harm to persons as well. If you have any questions in this regard please call the Help line or Metra at 1-800-221-0932 for assistance.
US.PAT.NOS.8014920and8214105
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV.
8/1
7/20
12
INST
-ASW
C
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA ASWC
IGNI
TION
TERM
INAL
S
WIR
ECU
TTERM3.
5
M2.
6M
3M
5
M4
ISO
62.
51.
5
CARACTERÍSTICAS DEL KIT
• Unainterfasehacetodo-Noserequiereninterfasesadicionales• Diseñadoparasercompatiblecontodaslasmarcasprincipales
deradios• Detectaautomáticamenteeltipodevehículo,laconexiónde
radioypreconfiguraloscontroles• Sepuedeprogramarmanualmenteenlamayoríadelosvehículos• Lamemoriaretienelaconfiguracióninclusodespuésdequese
desconectelabateríaoseeliminelainterfase• Lasconexionesestánorganizadasparaquedardetrásdelradio• ActualizablemedianteUSB
COMPONENTES DE LA INTERFAZ
•InterfaseASWC•Arnésde12pinsconconectormachode3.5mm•Conectorhembrade3.5mmconcablesmarrón
ymarrón/blanco•Resistenciade12k-ohmios
HERRAMIENTAS REQUERIDAS
•Cortador•Pelacables•Cinta•Conectores(p.ej.,conectoresatope,tapasacampanadas,etc.)
Manual de instalaciónde la interfase de control
en volante Axxess
ASWC
US.PAT.NOS.8014920and8214105
Índice
Prefacio ............................................................................................. 3
Información general– IntroducciónalainterfaseASWCyalarnésdecableado ...............4-5
ASWC– Sección1:Instalación ....................................................................6-7
– Sección2:Programación ...............................................................8-9
– Sección3:Resolucióndeproblemas
Mododedetecciónautomática .................................................. 10
Programaciónmanual ..........................................................10-13
Cambiodetipoderadio........................................................13-14
Programacióndetipoderadiomanual .................................14-15
– Sección4:Remapeo
RemapeodebotonesSWC ........................................................ 16
RestablecimientodelosajustesoriginalesdeSWC .................... 17
Leyenda ASWC– RetroalimentaciónLEDdelvehículo ................................................ 18
– RetroalimentaciónLEDdelradio ................................................18-19
– Asignacióndebotones(remapeo/programaciónmanual) ................ 19
PRECAUCIÓN: Metra recomienda desconectar el terminal negativo de la batería antes de comenzar cualquier instalación. Todos los accesorios, interruptores y, especialmente, las luces indicadoras de airbag deben estar enchufados antes de volver a conectar la batería o comenzar el ciclo de ignición.
Nota: Remítase a las instrucciones incluidas con el radio de postventa.
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 AxxESSINTERfACE.COM
Lo que debe saber antes de empezar
1) Conozcaelaño,marcaymodelocorrectosdesuvehículo.
2) AsegúresedequeelradioqueestáinstalandoseacompatibleconlainterfasedecontrolenvolanteAxxess(ASWC)(consulteelmanualdelpropietariodelradiodemercadosecundario).
3) VayaalsitiowebdeAxxess(www.axxessinterface.com)yhagaclicen“SteeringWheelControl”(SWC,controlenvolante),localizadoenlapartederechadelapantalla.Despuésdeingresarlosdatosdesuvehículoyhacerclicen“Submit”(Enviar),apareceráunanuevapáginacondosfuentesdeinformación.Una, undocumentoenformatoPDFlocalizadodebajoenlapestaña“Documents”(Documentos).Ysegundo,informacióndetalladasobreloscoloresdecablesdecontrolenelvolantequetendrásuvehículobajolapestaña“VehicleInformation”(Informacióndelvehículo).ImprimaeldocumentoPDFparaquelotengaensuvehículodurantelainstalación,yaqueestaeslamejorfuentedeinformación,ademásdeserlamásfácil.
Nota: Aunque hemos llevado a cabo pruebas e investigación extensas (para verificar que los colores de los cables del control en el volante de los vehículos que enumeramos sean correctos), sigue siendo responsabilidad suya verificar los cables del control en el volante con un multímetro. Si encuentra alguna discrepancia, por favor notifique a nuestro Departamento Técnico al 1-800-253-TECH. Por favor llame desde su vehículo, cuando tenga acceso a la interfase y al cableado del vehículo.
Prefacio
3
4
Introducción a la interfase ASWC y al arnés de cableado
EnlapartesuperiordelainterfaseASWChaytrespuntosdeinterés:
1) El foco LED de programación –Parpadearápidamentecuandoestáenmododedetecciónautomática,parpadealentamenteenelmododeprogramaciónmanual.
2) El botón de restablecimiento–Mantengapresionadoelbotóndurante3segundosparainiciarelmododedetecciónautomática;manténgalopresionadomásde10segundosparainiciarelmododeprogramaciónmanual.
3) La cubierta deslizable(cubiertadelpuertoUSB)–ÁbralapararevelarelpuertodeactualizaciónmedianteUSB.UtilizandoelcabledeactualizaciónmedianteUSB-CAByelsitiowebdeAxxesspuedeasegurarsedesiempretenerelinventariomásactualizado.
Información general
CubiertadelpuertoUSB Botónderestablecimiento LEDdeprogramación
5
Información general
Pin- 1 Rosa
Pin- 2 Blanco/Verde
Pin- 3 Amarillo/Verde
Pin- 4 Verde/Anaranjado
Pin- 5 Gris/Rojo
Pin- 6 Negro
Pin- 7 Azul/Rosa
Pin- 8 Negro/Verde
Pin- 9 Rojo (punta de
conector 3.5mm)
Pin- 10 Blanco (aro de
conector 3.5mm)
Pin- 11 Gris/Azul
Pin- 12 Rojo
AcontinuaciónseindicanloscoloresdeloscablesparaelASWC.VisiteelsitiowebdeAxxessenwww.axxessinterface.comparaobtenerinformacióndetalladasobresuvehículoespecíficoyparavercuálescoloresdecablesusarconlainterfaseASWC.
6
Sección 1: Instalación
UnavezquehayarecolectadooimpresolahojadeinformaciónsobresuvehículoespecíficodelsitiodeAxxess(www.axxessinterface.com),estálistoparainstalarelASWC.
Instalación del ASWC
1) ConecteelcableNegrodelASWCatierra.Puedeutilizarelmismopuntodeaterrizadoqueelradiodemercadosecundario.
2) ConecteelcableRojodelASWCauncabledeaccesoriosde12-voltsqueseenciendayseapagueconlallavedeignición.
3) LocaliceloscablescorrectosdelSWCenelarnésprimarioosecundariodelvehículocomosedescribeenlahojadeinformacióndelvehículoqueseencuentraenelsitiowebdeAxxess.ConecteloscolorescorrectosdecabledesdeelASWCaloscablesdecontrolenelvolantedelvehículo.
Nota: Metra recomienda que el o los cables se suelden para lograr la mejor conexión, y la más segura. No se recomienda el uso de conectores tipo “T-Tap” o “Scotchlock” debido a que aumenta la probabilidad de intermitencia en la conexión o cambio en los valores de resistencia.
4) SiestáutilizandounradioEclipse,Kenwood,MetraOEounradioJVCmásnuevo,conecteelconectorhembrade3.5mmincluidoconloscablesMarrónyMarrón/Blancoenelconectormachode3.5mmdelarnésdeASWC.
Continúa en la página
7
Sección 1: Instalación
• Para Kenwood y algunos JVC: ConecteelcableSWC(normalmenteAzul/Amarillo)alcableMarróndelASWC.
AísleyencinteelcableMarrón/Blanco,noseutilizará.
Nota: Algunos de los radios Kenwood más nuevos se detectarán automáticamente como JVC. Si este es el caso, puede usar una resistencia de 12k ohmios (incluida) en línea entre el cable Azul/Amarillo y marrón del conector hembra de 3.5mm durante la programación únicamente. O puede configurar manualmente el tipo de radio que está en la sección de programación de este manual.
• Para Eclipse:ConecteloscablesSWCdelEclipse(normalmenteMarrónyMarrón/Negro)aloscablesMarrón yMarrón/BlancodelASWC.MarrónvaconMarrónyMarrón/BlancovaconMarrón/Negro.Enocasionesestoesalrevés;inviertaloscablessisenecesita.
• Para Metra OE: ConecteelcableSWCClave1(Gris)alcableMarróndelASWC.
5) Paratodoslosdemásradios,conecteelconectormachode3.5mmdelASWCenlaparteposteriordelradiodemercadosecundario,designadaparaunainterfasedecontrolexternoSWC.Sitienedudassobredóndevaelconectorde3.5mmdelASWC,consulteelmanualdelradiodemercadosecundario.Cuandohayahechotodaslasconexiones,conecteelradiodemercadosecundariosiaúnnolohabíahecho.
8
ElASWCpuedeprogramarsededosmaneras.(1)Puedehacerloautomáticamentemedianteelmododedetecciónautomática,o(2)puedeprogramarsemanualmenteenvehículosquenocuentancondatos.Serecomiendaempezarconel“Mododedetecciónautomática”primero.
Modo de detección automática: Información generalElASWCtienelacapacidaddedetectarautomáticamenteciertosvehículosydesaberacuálradiodemercadosecundarioestáconectado.LahojadeinformacióndelvehículodelsitiowebdeAxxess(www.axxessinterface.com)indicarásisuvehículoserádetectadoautomáticamenteyquéaccióndebeseguirustedparaqueesteprocesoselleveacabo.
Paraquelafuncióndedetecciónautomáticafuncione,hay3posiblesacciones.Sinembargo,soloserequiereunaaccióndesuparte,dependiendodesuvehículo.
• Enciendalaigniciónynoserequiereningunaotraacción.
• Enciendalaignición,presioneymantengapresionadoelbotóndesubirvolumenenelvolante.
--- O bien ---
• Enciendalaignición,presioneysuelteelbotóndesubirvolumenenelvolante.
Comoseexplicóanteriormente,solosenecesitaráunadeestasacciones,dependiendodesuvehículoparaquefuncionelafuncióndedetecciónautomática.ConsultelahojadeinformacióndelvehículoproporcionadaenelsitiowebAxxess.
Modo de detección automática: Pasos1) Realicelasconexionesalvehículoyalradiodemercadosecundario.
SiestaeslaprimeravezqueseinstalaelASWCenunvehículo:
2)Enciendalaignición;elfocoLEDempezaráaparpadearrápidamente,
Sección 2: Programación
9
Sección 2: Programación
loquesignificaqueelASWCestábuscandoelvehículoyelradio.Continúeconelpaso4.
--- O bien ---
SielASWCseinstalóenunvehículopreviamente:
2) Enciendalaignición,elfocoLEDparpadearáunavezyluegoseapagará.
3) Mantengapresionadoelbotónderestablecimientodurante3segundosyluegosuéltelo.
4) Realicelaacciónrequeridaparasuvehículoespecíficocomoseindicaenlahojadeinformacióndelvehículo.
5) Despuésdeunpardesegundos,elfocoLEDdebedejardeparpadearynoiluminarsedurantehasta2segundos.Enestemomento,nopresioneningúnbotón.
6) Despuésdelos2segundos,habráunaseriede7parpadeos,algunoscortosyalgunoslargos.
7) ElfocoLEDpausaráduranteotros2segundosyluegoparpadearáhasta11veces(consultelaleyendadelASWC).
8) Esteeselfinaldelaetapadedetecciónautomática.SielASWCdetectóelvehículoyelradiodeformaexitosa,elfocoLEDseiluminaráencolorrojosinparpadear.
9) ParavehículosconbotonesBluetoothdelfabricanteoriginal,presione“Colgar”o“Descolgar”enelcontroldesuvolantedespuésdequeelfocoLEDsehayailuminadosinparpadear.SilosbotonesdeBluetoothdelfabricantedeequipooriginalpuedenutilizarse,elfocoLEDseapagarádespuésde3segundos.SusbotonesdeBluetoothdelfabricantedeequipooriginalahoraestánprogramadosparalosbotonesBluetoothdesuradiodemercadosecundario(elradiodemercadosecundariodebesercompatibleconBluetooth).
Tip: Si el foco LED no se ilumina en color rojo sin parpadear, consulte la sección de resolución de problemas.
10)Asegúresedequelosbotonesdecontrolenelvolantefuncionencorrectamenteenelvehículoydisfrute.
10
Modo de detección automática
AsíqueyaprobólafuncióndedetecciónautomáticayalfinalelfocoLEDnosequedódecolorrojosinparpadear.Enlugardeello,empezóaparpadear,loquesignificaqueelASWCnodetectóelvehículo.
Sigaestospasosparadeterminarquépuedehaberocurrido:
1) Verifiquequetieneunaccesoriode12-voltsyunabuenatierraalASWC.Enocasioneslatierradefábricanoessuficiente,serecomiendaampliamenteunatierraachasís.SisuvehículotieneuncabledetierradereferenciadeSWC, póngaloatierratambiénconelchasís,juntoconsuradiodemercadosecundario.
2) Valideusandolahojadeinformacióndelvehículo(sitiowebAxxess)queeloloscablesdecontrolenelvolantedelvehículocorrectossehayanconectadoaeloloscablescorrectosdelASWC.
3) Confirmequeelconectorde3.5mmestéconectadofirmementeasuradioyqueestéenellugarcorrecto.
4) Siutilizaelconectorhembrade3.5mmenunradioEclipse,Kenwood,algunosJVCoMetraOE,verifiquequeelcableSWCdelradioestéconectadoalcablecorrectoalASWC.
Programación manual del modo de detección automática
SisuvehículonoestáenlalistadedetecciónautomáticadelASWCenelsitiowebAxxess,www.axxessinterface.com,puedeprogramarmanualmenteunvehículosindatossiguiendoestospasos(tengalaleyendaASWCdisponible).
Nota: No todos los radios tendrán todos los comandos SWC posibles en el volante. Los radios de mercado secundario que no tengan
Sección 3: Resolución de problemas
11
Bluetooth no reconocerán los comandos PPT (presionar para hablar) o de teléfono colgado o descolgado; sin embargo, estos botones pueden programarse manualmente para realizar otros comandos en algunos casos. Consulte el manual del propietario del radio o el control remoto para ver los comandos específicos que el radio puede reconocer.
1) Realicelasconexionesalvehículoyalradiodemercadosecundario,asegúresedequeelconectorde3.5mmestéconectado.
SiestaeslaprimeravezqueseinstalaelASWCenunvehículo:
2) Enciendalaignición;elfocoLEDempezaráaparpadearrápidamente.
3) Despuésde10segundos,elASWCentraráenmododeretroalimentacióndeLED.DespuésdequelaseriedeLEDparpadee,elfocoLEDsequedaráenunestadodeparpadeolentoconstante.Continúeconelpaso4.
--- O bien ---
SielASWCyasehausadoantesenotrovehículo:
2) Presioneymantengapresionadoelbotónderestablecimientodurantemásde10segundos.
3) Despuésdelos10segundos,elfocoLEDempezaráaparpadearlentayconstantemente.
4) Enestemomento,presioneymantengapresionadoelbotón“Subirvolumen”enelvolantedurante7segundoshastaqueelfocoLEDseilumineenrojosinparpadear.AhorasuelteelbotóndesubirvolumenyesperehastaqueelfocoLEDseapague.Conestoquedaprogramadoelbotóndesubirvolumen.
Sección 3: Resolución de problemas
12
5) Ahorapresioneymantengapresionadoelbotónde“Bajarvolumen”hastaqueelfocoLEDseiluminedecolorrojosinparpadear.SuelteelbotónyelfocoLEDseapagará.Conestoquedaprogramadoelbotóndebajarvolumen.
6) Enestemomento,vayaalaseccióndeasignacióndebotonesdelaleyendaASWC(remapeo/programaciónmanual),página19,ycontinúeconelbotón“Buscarsiguiente”.
7) Puedeterminarestamitaddelaprogramaciónde2maneras:
(1) Despuésdeprogramarelúltimobotóndesuvolante(notienequehacertodalalista),mantengapresionadoelbotónde“Subirvolumen”durantecuandomenos10segundos.ElfocoLEDseiluminaráenunmododeparpadeolentoyconstante.
--- O bien ---
(2) Despuésdequeprogrameosesalteelbotónnúmero18,elfocoLEDvolveráalmododeparpadeolentoyconstante.
Nota: Si en cualquier momento se equivoca, mantenga presionado el botón de restablecimiento en el ASWC durante 10 segundos o más. Esto reiniciará la programación manual. Vuelva al Paso 4 y empiece de nuevo.
8) Presioneymantengapresionadoelbotóndebajarvolumendurante5segundoshastaqueelfocoLEDempieceaparpadearrápidamente.
9) Suelteelbotóndebajarvolumen.
10) Despuésde4segundosdequeelfocoLEDparpadeerápidamente,esteseapagarádurante2segundos.
11) LuegoelfocoLEDparpadearáhasta11veces,dependiendodelradioalqueelASWCpiensequeestáconectado.
Sección 3: Resolución de problemas
13
12) Asegúresedequelacantidaddeparpadeoscorrespondaalradioquetieneinstalado.ConsultelasecciónCambiareltipoderadio,enlaspáginas13y14.
13) SilosparpadeosdelfocoLEDcorrespondenalradio,mantengapresionadoelbotóndebajarvolumenhastaqueelfocoLEDseilumineencolorrojosinparpadear.
14)Laprogramacióndelvehículoydelradiohafinalizado.Pruebelasfuncionesdelcontrolenelvolanteparaasegurarsedequefuncionencorrectamente.
Cambio de tipo de radio
SielparpadeodelfocoLEDnocorrespondealradioquetieneconectado,debeprogramarmanualmenteelASWCparaindicaracuálradioestáconectado.
1) Paraprogramarmanualmenteelradiodemercadosecundario,presioneymantengapresionadoelbotóndebajarvolumenenelcontroldelvolantehastaqueelfocoLEDsequedeenrojosinparpadear,luegosuelteelbotóndebajarvolumen.
2) Enestemomento,elEclipseestáprogramado.SiestáutilizandounradioEclipse,vayaalpaso3.Siestáutilizandootroradio,vayaalpaso4.
3) Presioneymantengapresionadoelbotóndebajarvolumendurante5segundos.ElfocoLEDparpadearáunavezyluegoseiluminarádecolorrojosinparpadear,indicandoquehafinalizado laprogramación.Disfrutedesuradio.
4) SisuradionoesEclipse,presioneelbotóndesubirvolumendenuevohastaqueelfocoLEDseilumineenrojosinparpadear,luegosuelteelbotóndesubirvolumen.HaprogramadoelradioKenwood.
Sección 3: Resolución de problemas
14
5) Estatablamuestracuántasvecesesnecesariopresionaralbotóndesubirvolumenparaelradioqueestátratandodeprogramar:
6) Unavezseleccionadoelfabricantedelradio,mantengapresionadoelbotóndebajarvolumencuandomenos5segundos.ElfocoLEDparpadearáelnúmerodevecesqueelradiosehayaseleccionadoyluegoelfocoLEDpermaneceráencendidoparaindicar queelASWChaterminadolaprogramación.
Programación de tipo de radio manual
Sisolorequierecambiareltipoderadio,sigaelprocedimientoindicadoacontinuación.
1) Enlosprimeros25segundosdespuésdeabrirlallave,presioneymantengapresionadoelbotóndebajarvolumendelauto.
2) Despuésde15segundosdepresionarelbotóndebajarvolumen,elfocoLEDrojodeASWCseencenderá.
3) SuelteelbotóndebajarvolumenyelfocoLEDseapagará.Ahoraestamosenmododeprogramaciónderadio.
Sección 3: Resolución de problemas
1 Eclipse2 Kenwood3 Clarion“Tipo1”4 SonyandDual5 JVC 6 PioneerandJensen
7 Alpine8 Visteon9 Valor10 Clarion“Tipo2”11 MetraOE
15
4) Presioneysuelteelbotóndesubirvolumenparaelnúmeroderadiodeseado(consultelaleyendadelASWC).Porcadavezquepresione,elfocoLEDrojoseencenderáyluegoseapagarácuandolosueltepararetroalimentación.
5) Cuandolleguealtipoderadiodeseado,presioneelbotóndebajarvolumen.
6) ElfocoLEDseencenderáypermaneceráencendido(aproximadamente3segundos).ElASWCestárealizandocálculosyalmacenamientointernodeestanuevainformación.
7) ElfocoLEDseapagará,indicandoquehaterminado.
Nota: Si en cualquier momento el usuario no presiona ningún botón durante 10 segundos o más, este modo de programación se abortará.
Sección 3: Resolución de problemas
16
Remapeo de los botones de SWC (control en el volante)
CuandoyatengaelASWCprogramado,puedecambiarlasasignacionesdelosbotonesdelcontrolenelvolante.Porejemplo,puedeprogramarelbotón“Buscarsiguiente”como“Silencio”.SigaestospasospararemapearlosbotonesSWC:
1) IdealmenteserecomiendatenerelASWC visible,paraquesepuedaverelparpadeodelfocoLEDparaconfirmarelreconocimientodelosbotones.
2) Serecomiendaapagarelradio.
3) Dentrodelosprimeros20segundosdespuésdeencenderlaignición,presioneymantengapresionadoelbotóndesubirvolumendurantecuandomenos20segundos.
4) ElfocoLEDseiluminaráenrojosinparpadear.SuelteelbotóndesubirvolumenyelfocoLEDseapagará.Conestoquedaprogramadoelbotóndesubirvolumen.
5) SigalalistaenlaseccióndeAsignacióndebotones,página19,paraconsultarelordendelosbotonesquedebenpresionarsey/ocómoomitirunbotón.
6) Despuésdeprogramarelúltimobotóndelvolante(notienequepasarportodalalista),mantengapresionadoelbotóndeaumentarvolumendurantealmenos10segundosyelfocoLEDseapagará.
--- O bien ---
Despuésdequeprogrameosesalteelbotónnúmero18,elfocoseapagaráyelremapeohabráterminado.
Sección 4: Remapeo
17
Restablecimiento de los ajustes originales de SWC
Siporalgúnmotivodespuésderemapearloscontrolesdelvolantequierevolveralosajustesoriginalesdelvolante,sigaestospasos:
1) Enlosprimeros20segundosdespuésdeencenderlaigniciónPresioneymantengapresionadoelbotónoriginaldebajarvolumen(noelbotóndebajarvolumenqueacabaderemapear)durantecuandomenos25segundos.
2) ElfocoLEDseencenderá;suelteelbotóndebajarvolumenyelfocoLEDseapagará.
3) Losajustesoriginalesdelcontroldelvolanteserestablecerán.
Sección 4: Remapeo
18
Para A y B: Los parpadeos cortosrepresentaneloloscablesdelcontrolenelvolantequenoestánconectadosalvehículodesdeelASWC.Los parpadeos largos representaneloloscablesqueestánconectadosalvehículo.
A. Retroalimentación LED del vehículo El1erparpadeodelfocoLEDeselcableBlanco/VerdedelASWC
El2oparpadeodelfocoLEDeselcableAnaranjado/VerdedelASWC
El3erparpadeodelfocoLEDeselcableVerde/AnaranjadodelASWC
El4oparpadeodelfocoLEDeselcableGris/RojodelASWC
El5oparpadeodelfocoLEDeselcableNegro/VerdedelASWC
El6oparpadeodelfocoLEDeselcableGris/AzuldelASWC
El7oparpadeodelfocoLEDeselcableRosadelASWC
B. Radio LED Feedback El1erparpadeodelfocoLEDesparaEclipse
El2oparpadeodelfocoLEDesparaKenwood
El3erparpadeodelfocoLEDesparaClarion(“Tipo”1)
El4oparpadeodelfocoLEDesparaSonyyDual
El5oparpadeodelfocoLEDesparaJVC
El6oparpadeodelfocoLEDesparaPioneeryJensen
El7oparpadeodelfocoLEDesparaAlpine*
El8oparpadeodelfocoLEDesparaVisteon
El9oparpadeodelfocoLEDesparaValor
Leyenda ASWC
19
C. Asignación de botones(remapeo/programaciónmanual)
Leyenda ASWC
1.Subirvolumen
2.Bajarvolumen
3.Buscarsiguiente
4.Buscaranterior
5.Fuente/Modo
6.Silencio
7.Subirprestablecido
8.Bajarprestablecido
9.Encendido
10.Banda
11.Reproducir/Aceptar
12.PTT(presionar para hablar)
13.Colgado
14.Descolgado
15.Aumentarventilador
16.Disminuirventilador
17.Aumentartemperatura
18.Disminuirtemperatura
Nota: No todos los radios tienen todos estos comandos. Consulte el manual del propietario del radio o comuníquese con el proveedor del radio directamente para obtener los comandos específicos reconocidos por ese radio en particular.
Si la siguiente función de la lista no está en el volante, presione el botón de subir volumen durante 1 segundo hasta que el foco LED se encienda, luego suelte el botón. Esto le indica al ASWC que la función no está disponible y pasará a la siguiente función.
El10oparpadeodelfocoLEDesparaClarion(“Tipo”2)
El11voparpadeodelfocoLEDesparaMetraOE
*Nota (sección B): Si el ASWC parpadea 7 veces y no tiene un radio Alpine conectado a él, esto significa que el ASWC no detectó ningún radio conectado. Verifique que el conector de 3.5mm esté conectado a la entrada de SWC en el radio.
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA ASWC
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 AxxESSINTERfACE.COM
REV.
8/1
7/20
12
INST
-ASW
C
KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians
IMPORTANT WARNING
Thisproductincludesinstructionsforinstallationwhichmustbecarefullyfollowed.Theinstructionsarewordedinsuchamannertoassumethattheinstalleriscapableofcompletingthesetypeofelectronicinstallations.Ifyouareunclearastowhatyouareinstructedtodoorbelievethatyoudonotunderstandtheinstructionssoastoproperlyandsafelycompletetheinstallationyou should consult a technician who does have this knowledge and understanding.
Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or to safety systems on the vehicle. Interference with certain safety systems could cause harm to persons as well. If you have any questions in this regard please call the Help line or Metra at 1-800-221-0932 for assistance.
US.PAT.NOS.8014920and8214105
top related