Apprenticeship Curriculum Standard Tool and Die Maker Tool ... · This curriculum revision for the Level 2 – Tool and Die Maker – Tool/Tooling Maker for is based upon the on-the-job
Post on 28-Feb-2020
0 Views
Preview:
Transcript
Apprenticeship Curriculum Standard
Tool and Die Maker Tool/Tooling Maker
Level 2 Intermediate
430A & 630T
2008
Please Note: Apprenticeship Training and Curriculum Standards were developed by the Ministry of Training, Colleges and Universities (MTCU). As of April 8th, 2013, the Ontario College of Trades (College) has become responsible for the development and maintenance of these standards. The College is carrying over existing standards without any changes. However, because the Apprenticeship Training and Curriculum Standards documents were developed under either the Trades Qualification and Apprenticeship Act (TQAA) or the Apprenticeship and Certification Act, 1998 (ACA), the definitions contained in these documents may no longer be accurate and may not be reflective of the Ontario College of Trades and Apprenticeship Act, 2009 (OCTAA) as the new trades legislation in the province. The College will update these definitions in the future. Meanwhile, please refer to the College’s website (www.collegeoftrades.ca) for the most accurate and up-to-date information about the College. For information on OCTAA and its regulations, please visit: www.collegeoftrades.ca/about/legislation-and-regulations.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
TABLE OF CONTENTS Introduction .............................................................................................................. 1 Program Summary of Reportable Subjects ........................................................... 2 S0649 Applied Trade Calculations, Charts, Tables ....................................... 3 S0649.1 Solve trade-specific problems involving the Pythagorean Theorem and solve for unknown values .................................................. 4 S0649.2 Solve trade-specific problems involving right angle triangle trigonometry and solve for unknown values ................................ 4 S0649.3 Solve trade-specific problems involving circles and solve for unknown values ................................................................................. 5 S0649.4 Perform tool and die trade-specific calculations ...................................... 5 S0650 Engineering Drawings/CAD Data ........................................................ 6 S0650.1 Describe the graphic language and symbols of engineering drawings/CAD data .................................................................................. 7 S0650.2 Describe dimensional terminology, symbols and practices...................... 8 S0650.3 Demonstrate sketching of revolved, removed, partial, and broken out sectional views ....................................................................... 9 S0650.4 Identify tolerance, allowance, and symbols as applied to the dimensioned features of a workpiece .............................................. 10 S0650.5 Describe elements and features of jig and fixture drawings and production drawings/CAD data .............................................................. 10 S0650.6 Identify the features, elements, types, and terminology of engineering drawings/CAD data for gears, cams, and bearings ............ 11 S0650.7 Develop an operational plan for machining jig and fixture components. .......................................................................................... 11 S0651 Metallurgy of Jig and Fixture Components ...................................... 12 S0651.1 Describe safe working procedures associated with heat-treating furnaces and hand held equipment .................................. 13 S0651.2 Describe ferrous metal heat-treating processes .................................... 14 S0651.3 Describe hardness testing methods ...................................................... 15 S0651.4 Describe elements and machinability of non-ferrous metals ................. 16
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
S0652 Metrology (Measuring and Checking) ................................................ 17 S0652.1 Identify the fundamentals of dimensional metrology .............................. 18 S0652.2 Describe the fundamentals of measuring, checking, and gauging equipment ........................................................................ 19 S0652.3 Demonstrate measuring techniques using direct/indirect reading linear measuring equipment...................................................... 20 S0652.4 Describe measuring techniques using inspection and checking gauges .................................................................................... 20 S0652.5 Describe measuring and checking procedures using indicating gauges and comparators ....................................................... 21 S0652.6 Describe surface roughness measurement procedures ........................ 21 S0653 Turning Technology ........................................................................... 22 S0653.1 Describe safe working procedures when setting up and operating a lathe .................................................................................... 23 S0653.2 Set up lathe workholding devices, attachments, and accessories ......... 23 S0653.3 Set up lathe thread and/or form cutting tools and tool holders .............. 24 S0653.4 Demonstrate turning techniques to produce jig and fixture components ........................................................................................... 24 S0654 Milling Technology ............................................................................. 25 S0654.1 Describe safe working procedures when setting up and operating milling machines .................................................................................... 26 S0654.2 Identify milling attachments to machine jig and fixture components ...... 26 S0654.3 Demonstrate set-up procedures for horizontal or vertical mill workholding devices and accessories .................................................... 27 S0654.4 Demonstrate the assembly of cutting tools and tool holders ................. 27 S0654.5 Develop a plan for milling and boring..................................................... 27 S0654.6 Perform milling and boring ..................................................................... 28 S0655 Grinding Technology .......................................................................... 29 S0655.1 Describe safe working procedures when setting up and operating grinders .................................................................................................. 30 S0655.2 Select surface or cylindrical grinder controls and coolant ...................... 31 S0655.3 Set up surface or cylindrical grinder workholding devices, accessories, and attachments ............................................................... 32 S0655.4 Demonstrate mounting, truing and dressing of grinding wheels ............ 33 S0655.5 Develop a plan for grinding flat surfaces, tapers, angles, and profiles ............................................................................................ 33 S0655.6 Perform grinding .................................................................................... 33
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
S0560 Ram/Sink Electrical Discharge Machining (EDM) Technology ........ 34 S0656.1 Describe safety procedures when setting up and operating EDM machines ...................................................................................... 35 S0656.2 Describe machine controls, dielectric fluid requirements, and settings of ram/sink type EDM machines ........................................ 36 S0656.3 Describe assembly of EDM electrodes and holders .............................. 36 S0656.4 Select ram/sink EDM techniques to spark erode jig and fixture components ........................................................................................... 37 S0656.5 Describe routine maintenance ............................................................... 37
S0657 Machining Centre Computerized Numerical Control (CNC) Technology .......................................................................................... 38 S0657.1 Describe safe working procedures when setting up and operating CNC machining centres ......................................................................... 40 S0657.2 Describe operating principles and applications of CNC machining centres ................................................................................................... 41 S0657.3 Describe the basics of CNC dimensioning ............................................. 42 S0657.4 Describe part programming methods, set-up sheets, tooling lists, part program manuscripts, and input media .......................................... 43 S0657.5 Describe manual operation systems for CNC machining centres .......... 44 S0657.6 Develop a plan for a CNC machining centre .......................................... 44 S0657.7 Demonstrate procedures for entering and verifying a program for a CNC machining centre to perform linear and circular machining exercises ................................................................................................ 45 S0658 Tooling Technology (Jigs and Fixtures) ............................................ 47 S0658.1 Describe the rationale for using jigs and fixtures when manufacturing components ................................................................... 48 S0658.2 Describe types and classifications of jigs ............................................... 48 S0658.3 Describe types and classifications of fixtures ........................................ 49 S0658.4 Describe jig and fixture tooling ............................................................... 49 S0658.5 Describe jig and fixture design characteristics ....................................... 50
S0659 Tooling Assembly Techniques for Jigs and Fixtures ...................... 51 S0659.1 Describe safe working habits when assembling tooling components ................................................................................ 52 S0659.2 Identify up equipment for fitting, positioning, and aligning tooling components and attachments .................................................... 53 S0659.3 Describe processes and techniques for the assembly of keyed components ................................................................................. 53 S0659.4 Describe processes and techniques for the assembly of dowelled components ............................................................................ 54 S0659.5 Describe final assembly processes and techniques .............................. 55
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
S0660 Jig and Fixture Building ..................................................................... 56 S0660.1 Interpret engineering, CAD data, part drawings, component prints, assembly, jig, and fixture prints.............................................................. 57 S0660.2 Interpret documentation ......................................................................... 58 S0660.3 Demonstrate detailed sketching of a component from engineering
drawings and CAD data ....................................................................... 58 S0660.4 Identify jig and fixture materials ............................................................. 58 S0660.5 Produce a plan for the jig and fixture building process .......................... 59 S0660.6 Demonstrate the machining, fitting, and assembling of jig and fixture components ................................................................................ 59 S0660.7 Demonstrate jig and fixture assembly procedures ................................. 60
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 1 - © Ontario College of Trades
INTRODUCTION This curriculum revision for the Level 2 – Tool and Die Maker – Tool/Tooling Maker for is based upon the on-the-job performance objectives, located in the industry-approved training standard. The curriculum is organized into 12 reportable subjects. The Program Summary of Reportable Subjects chart summarizes the training hours for each reportable subject. The curriculum identifies only the learning that takes place off-the-job. The in-school program focuses primarily on the theoretical knowledge and the essential skills required to support the performance objectives of the Apprenticeship Training Standards. Employers/Sponsors are expected to extend the apprentice’s knowledge and skills through practical training on the work site. Regular evaluations of the apprentice’s knowledge and skills are conducted throughout training to ensure that all apprentices have achieved the learning outcomes identified in the curriculum standard. It is not the intent of the in-school curriculum to perfect on-the-job skills. The practical portion of the in-school program is used to reinforce theoretical knowledge. Skill training is provided on the job.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 2 - © Ontario College of Trades
Program Summary of Reportable Subjects – Level 2
Number Reportable subjects Hours Total
Hours Theory
Hours Practical
S0649 Applied Trade Calculations, Charts, Tables 30 30 0
S0650 Engineering Drawings/CAD Data 30 12 18
S0651 Metallurgy of Jig and Fixture Components 12 8 4
S0652 Metrology (Measuring and Checking) 6 4 2
S0653 Turning Technology 6 2 4
S0654 Milling Technology 12 4 8
S0655 Grinding Technology 21 6 15
S0656 Ram/Sink EDM Technology 6 6 0
S0657 Machining Centre CNC Technology 24 12 12
S0658 Tooling Technology (Jig and Fixtures) 12 7 5
S0659 Tooling Assembly Techniques for Jig and Fixtures 18 6 12
S0660 Jig and Fixture Building 63 23 40
Total 240 120 120
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 3 - © Ontario College of Trades
Number: S0649 Reportable Subject: APPLIED TRADE CALCULATIONS, CHARTS &
TABLES Duration: Total 30 hours Theory 30 hours Practical 0 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0649.1 Solve trade-specific problems involving
Pythagorean Theorem and solve for unknown values. (4 hrs)
S0649.2 Solve trade-specific problems involving right angle triangle trigonometry and solve for unknown values. (10 hrs)
S0649.3 Solve trade-specific problems involving circles and solve for unknown values. (4 hrs)
S0649.4 Perform tooling and die trade-specific calculations. (12 hrs)
Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
100% 0% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 4 - © Ontario College of Trades
S0649.0 Applied Trade Calculations, Charts & Tables Duration: Total 30 hours Theory 30 hours Practical 0 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5268, U5269, U5270, U5271, U5272, U5273, U5274, U5275, U5276, U5277, U5278, U5279; 630T: U5555, U5556, U5557, U5558, U5559, U5560, U5561, U5562, U5563, U5564, U5565, U5566, U5567, U5568, U5569
GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to apply mathematical principles to trade-specific applications. LEARNING OUTCOMES AND CONTENT 49.1 Solve trade-specific problems involving the Pythagorean Theorem and solve
for unknown values. (4 hrs) Describe the application of the Pythagorean Theorem. Calculate the values of unknown sides of right angle triangles using the Pythagorean Theorem. 49.2 Solve trade-specific problems involving right angle triangle trigonometry and
solve for unknown values. (10 hrs) Describe the sides of a right angle triangle with reference to each of the
angles. Describe the six trigonometric functions of right angle triangles:
• sine • cosine • tangent • cotangent • secant • cosecant
Calculate the values of unknown sides and angles of a right angle triangle: • values of a trigonometric function • values of two sides • values of one side and one angle • ratio of sides
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 5 - © Ontario College of Trades
49.3 Solve trade-specific problems involving circles and solve for unknown values. (4 hrs)
Describe a circle and the parts of the circle: • circumference • chord • diameter • radius • arc • tangent • secant • segment • central angle • inscribed angle
Calculate the values of unknown parts of a circle involving:
• geometric shapes inside a circle • geometric shapes outside a circle
49.4 Perform tool and die trade-specific calculations. (12 hrs)
Perform trade-specific calculations to determine • tapers • bevels • distance between holes • distance between v slots • Vee-block applications • dovetails • draft angles • slide angles • cam angles • three-wire method • thread measurement
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 6 - © Ontario College of Trades
Number: S0650 Reportable Subject: ENGINEERING DRAWINGS/CAD DATA Duration: Total 30 hours Theory 12 hours Practical 18 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606,
S0607, S0608, S0609, S0610, S0611 Content: S0650.1 Describe the graphic language and symbols of
engineering drawings and CAD data. (2 hrs) S0650.2 Describe dimensional terminology, symbols
and practices. (2 hrs) S0650.3 Demonstrate sketching of revolved, removed,
partial, and broken out sectional views. (9 hrs) S0650.4 Identify tolerance, allowance, and symbols as
applied to the dimensioned features of a workpiece. (10 hrs)
S0650.5 Describe elements and features of jig and fixture drawings, production drawings, and CAD data. (2 hrs)
S0650.6 Identify the features, elements, and types of gears, cams, and bearings. (2 hrs)
S0650.7 Develop an operational plan for machining jig and fixture components. (3 hrs)
Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
40% 60% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Shop Text Books Interpreting Engineering Drawings Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 7 - © Ontario College of Trades
S0650.0 Engineering Drawings/CAD Data Duration: Total 30 hours Theory 12 hours Practical 18 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5268, U5269, U5270, U5271, U5272, U5273, U5274, U5275, U5276, U5277, U5278, U5279; 630T: U5555, U5556, U5557, U5558, U5559, U5560, U5561, U5562, U5563, U5564, U5565, U5566, U5567, U5568, U5569 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to sketch revolved, removed, partial, and broken out sectional views; identify GDT terminology; and, plan for machining jig and fixture components. LEARNING OUTCOMES AND CONTENT 50.1 Describe the graphic language and symbols of engineering drawings and CAD
data. (2 hrs)
Interpret types of graphic representations: • detail • views • components • sub-assembly • working assembly • assembly sequence • location • surface texture • positional tolerancing • machined surfaces • geometric symbols • not to scale • machining sequence
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 8 - © Ontario College of Trades
50.2 Describe dimensional terminology, symbols, and practices. (2 hrs)
Describe dimensional terms: • break line • (PCD) pitch circle diameter • (BCD) bolt circle diameter • across flats • pictorial • schematic • simplified
Describe dimensioning methods: • point-to-point • datum • tabular • arrowless Identify thread representations and designations: • acme • pipe • thread forms (ISO) • metric • unified • whitworth Identify screw thread designations for CSA, ANSI, MIL, and ISO forms: • nominal diameter • outside diameter (OD) • threads per inch • pitch • pitch diameter • class of fit • external • internal • left • right • thread forms Identify drawing elements related to workpiece processing techniques: • welding symbols • forging or casting draft angles • fillets • rounds • non-machined dimensional features • nominal dimensions
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 9 - © Ontario College of Trades
50.3 Demonstrate procedures for sketching revolved, removed, partial, and broken out sectional views. (9 hrs)
Identify types of sections views: • revolved • removed • partial • broken out Identify orthographic projections: • removed • partial • broken out Describe auxiliary views of orthographic projection.
Describe the basic function of an auxiliary view: • angular position • inclined surface • true shape • profile Describe the types of auxiliary views: • primary • secondary • sectional Describe types of sectional views: • partial • revolved • removed • offset • broken out Demonstrate sketching to scale section views: • offset • partial • revolved • removed • broken out
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 10 - © Ontario College of Trades
50.4 Identify tolerance, allowance, and symbols as applied to the dimensioned features of a workpiece. (10 hrs)
Identify geometric dimensioning and tolerancing terminology: • straightness • flatness • roundness (circularity) • cylindricity • profile of a line and a surface • angularity • perpendicularity • parallelism • position • concentricity • symmetry • feature control frame • general rules • virtual condition • total run-out • maximum material condition • regardless of feature size • least material condition • projected tolerance zone • basic dimension • datum feature and targets • circular run-out • correlative tolerance • datums
50.5 Describe elements and features of jig and fixture drawings, production
drawings, and CAD data. (2 hrs)
Identify details of jig and fixture drawings and production drawings for: • jigs/fixtures • gears • cams • bearings • bushings • gear, cam, and bearing drawings • simplified tool drawings (production drawings) • CAD data
Interpret features of a finished component using first or third angle projection.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 11 - © Ontario College of Trades
50.6 Identify the features, elements, and types of gears, cams, and bearings. (2 hrs)
Identify gear and cam symbols: • addendum • dedendum • circular pitch • diametral pitch • clearance • whole depth • tooth pressure angle • rise • fall • anti-friction • angular • sleeve • dwell • drop
Identify component parts of gears, cams, and bearings used in jig and fixture assembly: • helical springs • cams • roller bearings • retaining springs • “O” rings seals • swivel/universal joints
50.7 Develop an operational plan for machining jig and fixtures components. (3 hrs)
Interpret drawings/CAD data to identify machining methods and procedures. Describe ANSI, ISO & CSA standard limits and fits: • allowance • clearance • interference • tolerancing • interchangeability • nominal size • designation of fits • description of fits
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 12 - © Ontario College of Trades
Number: S0651 Reportable Subject: METALLURGY OF JIG AND FIXTURE COMPONENTS Duration: Total 12 hours Theory 8 hours Practical 4 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0651.1 Describe safe working procedures associated
with heat-treating furnaces and hand held equipment.
S0651.2 Describe ferrous metal heat-treating processes. (5 hrs)
S0651.3 Describe hardness testing methods. (5 hrs) S0651.4 Describe elements and machinability of non-
ferrous metals. (2 hrs) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
60% 40% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 13 - © Ontario College of Trades
S0651.0 Metallurgy of Jig and Fixture Components Duration: Total 12 hours Theory 8 hours Practical 4 hours Cross-Reference to Training Standards: 430A: U5267, U5268, U5276, U5277, U5278 U5279; 630T: U5557, U5558, U5567, U5568 U5569 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to describe the heat-treating and testing of ferrous and non-ferrous metals. LEARNING OUTCOMES AND CONTENT 51.1 Describe safe working procedures associated with heat-treating furnaces and
hand held equipment.
Identify potential safety hazards which may occur during the setting up and operating of heat-treating procedures. Identify heat-treating safe working habits and protective equipment including: • asbestos gloves • asbestos aprons • arm shields • face shields • checking workpieces • toxic fumes • good housekeeping • temperatures • ventilation • securing workpiece • stabilizing workpiece • fire hazards
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 14 - © Ontario College of Trades
51.2 Describe ferrous metal heat-treating processes. (5 hrs)
Describe flame hardening and tempering processes: • tempering colours • quenching media • surface preparation • workpiece holding/positioning • Describe the process and advantages for hardening of ferrous metals: • heat-treating specifications • quenching media • metallurgical structural change • hardness obtainable • strength • toughness • wear resistance • machinability • distortion • work preparation procedures • time-temperature cycle • depth of hardness • quenching procedures • pre-heating • cooling
Describe the process and advantages for pack and gas carburizing of steel: • heat-treating specifications • carbon content • hardenability • strength • toughness • wear resistance • machinability • type of furnace • carbonaceous mixtures • work preparation procedures • depth of case • selective areas to be carburized • time-temperature cycle
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 15 - © Ontario College of Trades
51.2 Continued
Describe the process and advantages for tempering of ferrous metals: • heat-treating specifications • metallurgical structural change • hardness • strength • toughness • wear resistance • machinability • time-temperature cycle • tempering colours
Describe the process and advantages for annealing of ferrous metals: • heat-treating specifications • internal stresses • machinability • type of furnace • cooling procedures Describe the process and advantages for normalizing of ferrous metals: • heat-treating specifications • internal stresses • grain refinement • machinability • cooling procedures
51.3 Describe hardness-testing methods. (5 hrs)
Describe hardness testing methods and procedures. Describe types and operating principles of hardness testers: • Rockwell • Brinell • Vickers • Scleroscope • Spark Describe the range and values of hardness tester scales. Describe the types of equipment for hardness testers: • penetrators • anvils • loads
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 16 - © Ontario College of Trades
51.4 Describe elements and machinability of non-ferrous metals. (2 hrs)
Describe the characteristics of non-ferrous metals: • smelting and shaping process • shapes • sizes • tolerances • surface conditions • UNS/SAE/ASTM code classifications • manufacturer=s code classifications • applications • properties
− chemical − physical − mechanical
• alloying elements • tensile strength • malleability • ductility • machinability • castability • weight comparison • hardness • corrosion resistance • wear resistance • colour • melting point
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 17 - © Ontario College of Trades
Number: S0652 Reportable Subject: METROLOGY (MEASURING AND CHECKING) Duration: Total 6 hours Theory 4 hours Practical 2 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0652.1 Identify the fundamentals of dimensional
metrology. (0.5 hrs) S0652.2 Describe the fundamentals of measuring,
checking, and gauging equipment. (0.5 hrs) S0652.3 Demonstrate measuring techniques using
direct/indirect reading linear measuring equipment. (1 hr)
S0652.4 Describe measuring and checking procedures using inspection and checking gauges. (2 hrs)
S0652.5 Describe measuring and checking procedures using indicating gauges and comparators. (1 hr)
S0652.6 Describe surface roughness measurement procedures. (1 hr)
Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
60% 40% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 18 - © Ontario College of Trades
S0652.0 Metrology (Measuring and Checking) Duration: Total 6 hours Theory 4 hours Practical 2 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5268, U5269, U5270, U5271, U5272, U5273, U5274, U5275, U5276, U5277, U5278, U5279; 630T: U5556, U5557, U5558, U5559, U5560, U5561, U5562, U5563, U5564, U5565, U5566, U5567, U5568, U5569 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to describe use of direct/indirect reading linear measuring equipment, inspection gauges, indicating gauges and comparators; describe surface roughness measurement procedures. LEARNING OUTCOMES AND CONTENT 52.1 Identify the fundamentals of dimensional metrology. (0.5 hrs)
Describe the fundamentals of dimensional metrology: • accuracy • precision • tolerances • reliability • limits • fits • datums • discrimination • lengths/widths • angular • straight • flat • square • round • surface texture • perpendicularity • parallel •
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 19 - © Ontario College of Trades
52.2 Describe the fundamentals of measuring, checking, and gauging equipment. (0.5 hrs)
Describe direct reading linear measuring equipment: • interchangeable anvil micrometer • bench micrometer • thread micrometer • indicating micrometer • deep throat micrometer • V-anvil micrometer • disc micrometer • blade micrometer • tube micrometer • wire micrometer • gear tooth vernier caliper • Describe indirect reading angular equipment: • sine plate • tool maker=s square • precision level Describe inspection and checking gauges: • plug gauges • ring gauges • snap gauges • profilometer • precision rollers • precision balls • thread wires • gear tooth rollers • Describe indicating gauges and comparators: • optical comparators • mechanical/electrical comparators • air gauges • optical flats Describe fundamentals and features of coordinate measuring machines (CMM).
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 20 - © Ontario College of Trades
52.3 Describe measuring techniques using direct/indirect reading linear measuring equipment. (1 hr)
Demonstrate measuring techniques using direct reading linear measuring equipment. Demonstrate measuring techniques using indirect reading angular equipment. Describe measuring techniques using inspection and checking gauges. Describe measuring techniques using indicating gauges.
52.4 Describe measuring and checking procedures using inspection and checking
gauges. (2 hrs)
Describe cleaning techniques of calibrated test specimen surfaces. Select inspection and checking gauges to check: • gear forms • profiles • pitch diameters • gear parts • gear teeth • angles • surface finishes • surface roughness • dimensions • contours Demonstrate inspection and recording techniques. Identify error sources in measurement techniques: • inherent instrument error • observational error • manipulative error • bias error • parallel error
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 21 - © Ontario College of Trades
52.5 Describe measuring and checking procedures using indicating gauges and comparators. (1 hr)
Describe cleaning techniques of calibrated test specimen surfaces. Describe features to be checked. Describe measuring techniques using indicating gauges and comparators: • optical comparators • mechanical comparators • air gauges • optical flats
Demonstrate inspection and recording techniques. 52.6 Describe surface roughness measurement procedures. (1 hr)
Describe cleaning techniques of calibrated test specimen surface. Describe surface roughness range. Identify surface roughness measuring equipment: • profilometer • surface texture gauge
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 22 - © Ontario College of Trades
Number: S0653 Reportable Subject: TURNING TECHNOLOGY Duration: Total 6 hours Theory 2 hours Practical 4 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0653.1 Describe safe working procedures when
setting up and operating a lathe. S0653.2 Set up lathe workholding devices,
attachments, and accessories. (0.5 hrs) S0653.3 Set up lathe thread and/or form cutting tools
and tool holders. (0.5 hrs) S0653.4 Demonstrate turning techniques to produce jig
and fixture components. (5 hrs) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
20% 80% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 23 - © Ontario College of Trades
S0653.9 Turning Technology Duration: Total 6 hours Theory 2 hours Practical 4 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5272, U5277, U5278; 630T: U5556, U5557, U5566, U5567, U5568 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to perform turning techniques to produce jig and fixture components. LEARNING OUTCOMES AND CONTENT 53.1 Describe safe working procedures when setting up and operating a lathe.
Identify potential safety hazards which may occur during the setting up and operating lathe. Demonstrate safe working habits including: • protective clothing • protective equipment and gear • good housekeeping • start-up • shut-off • securing workpiece/cutting tools • stabilizing workpiece/cutting tools • lubricants • lock-out procedures • tagging procedures
53.2 Set up lathe workholding devices, attachments, and accessories. (0.5 hrs)
Identify lathe workholding devices, attachments, and accessories: • taper attachment • tracing attachment • radius attachment • tool post grinder
Perform contact surface cleaning procedures.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 24 - © Ontario College of Trades
53.3 Set up lathe thread and/or form cutting tools and tool holders. (0.5 hrs)
Identify thread and tool geometry for lathe cutting tools. Describe lathe thread and/or cutting tools: • right • left • internal • external • form tools Demonstrate mounting, positioning, alignment, and securing procedures for form cutting tools and tool holders.
53.4 Perform turning techniques to produce jig and fixture components. (5 hrs)
Describe types of internal internal and external tapers and angles: • Jarno • Morse • Brown and Sharp Describe set-up procedures to produce an internal and external taper using: • tailstock offset • compound rest • taper turning attachments Describe methods of rough and finish turning. Describe methods of turning contoured surfaces: • external • internal • concave • convex • irregular Describe the finish allowance required by determining: • finish tolerance • surface finish Demonstrate turning of internal and external tapers and angles. Demonstrate turning of contours.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 25 - © Ontario College of Trades
Number: S0654 Reportable Subject: MILLING TECHNOLOGY Duration: Total 12 hours Theory 4 hours Practical 8 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0654.1 Describe safe working procedures when
setting up and operating milling machines. S0654.2 Identify milling attachments to machine jig and
fixture components. (2 hrs) S0654.3 Demonstrate set-up procedures for horizontal
or vertical mill workholding devices and accessories. (1 hr)
S0654.4 Demonstrate the assembly of cutting tools and tool holders. (2 hrs)
S0654.5 Develop a plan for milling and boring. (1 hr) S0654.6 Perform milling and boring. (6 hrs) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
30% 70% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 26 - © Ontario College of Trades
S0654.0 Milling Technology Duration: Total 12 hours Theory 4 hours Practical 8 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5273, U5276, U5277, U5278; 630T: U5556, U5557, U5563, U5566, U5567, U5568 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to mill and bore jig and fixture components. LEARNING OUTCOMES AND CONTENT 54.1 Describe safe working procedures when setting up and operating milling
machines.
Identify potential safety hazards which may occur during the setting up and operation of mills. Demonstrate safe working habits including: • protective clothing • protective equipment and gear • good housekeeping • start-up • shut-off • securing workpiece/cutting tool • stabilizing workpiece/cutting tool • lock-out procedures • tagging procedures
54.2 Identify milling attachments used to machine jig and fixture components. (2 hrs)
Identify milling attachments: • slotting head • horizontal attachment • vertical attachment • rack milling attachment • digital read-out
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 27 - © Ontario College of Trades
54.3 Demonstrate set up procedures for horizontal or vertical milling workholding devices and accessories. (1 hr)
Describe horizontal or vertical milling workholding devices and accessories: • dividing head • rotary table Demonstrate set up procedures. Demonstrate contact surface cleaning procedures.
54.4 Demonstrate the assembly of cutting tools and tool holders. (2 hrs)
Identify cutting tool geometry (nomenclature). Describe cutting tools and tool holders: • plain-milling • angular milling • form-milling • slitting saws • key seat milling • T-slot milling • dovetail milling • adaptors
Demonstrate cutting tool and tool holder assembly.
54.5 Develop a plan for milling and boring. (1 hr) Select milling procedures to mill types of surfaces: • horizontal • vertical • angular • contoured (form) Select milling procedures to bore holes. Select milling procedures to produce slots. Select milling workholding devices. Select cutting tools and tool holding devices and accessories.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 28 - © Ontario College of Trades
54.6 Perform milling and boring. (6 hrs)
Describe index milling using a dividing head. Describe index milling using a rotary table. Demonstrate milling horizontal, vertical, angular, and contoured surfaces. Demonstrate boring of holes.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 29 - © Ontario College of Trades
Number: S0655 Reportable Subject: GRINDING TECHNOLOGY Duration: Total 21 hours Theory 6 hours Practical 15 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0655.1 Describe safe working procedures when
setting up and operating grinders. S0655.2 Select surface or cylindrical grinder controls
and coolant. (1 hr) S0655.3 Set up surface or cylindrical grinder
workholding devices, accessories, and attachments. (1 hr)
S0655.4 Demonstrate mounting, truing and dressing of grinding wheels. (1 hr)
S0655.5 Develop a plan for grinding flat surfaces, tapers, angles, and profiles. (2 hrs)
S0655.6 Perform grinding. (13 hrs) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
30% 70% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 30 - © Ontario College of Trades
S0655 .0 Grinding Technology Duration: Total 21 hours Theory 6 hours Practical 15 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5271, U5276, U5277, U5278, U5279; 630T: U5556, U5557, U5561, U5566, U5567, U5568, U5269 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to grind jig and fixture components. LEARNING OUTCOMES AND CONTENT 55.1 Describe safe working procedures when setting up and operating grinders.
Identify potential safety hazards which may occur during grinder set-up and operational procedures. Demonstrate safe working habits including: • protective clothing and gear • good housekeeping • start-up • shut-off • securing workpiece • stabilizing workpiece • guards • dust extraction system • dressing wheel • inspecting wheel • ringing of wheel • maximum wheel rpm • lock-out procedures • tagging procedures
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 31 - © Ontario College of Trades
55.2 Select surface or cylindrical grinder controls and coolant. (1 hr) Describe functions and operating principles of cylindrical grinder.
Identify parts of cylindrical grinder: • in-feed control • table • bedways • base • wheelhead • table traverse mechanism • trip dogs • saddle • footstock • swivel table adjustment • work head Identify surface or cylindrical controls: • main switch • stop-start switch • table traverse • in-feed selection • cross-feed • wheel feed • cutting fluid • table dwell • workhead speed • feeds Describe cutting fluids: • soluble oils • synthetics • semi-synthetics
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 32 - © Ontario College of Trades
55.3 Set up surface or cylindrical grinder workholding devices, accessories, and attachments. (1 hr)
Describe grinder workholding devices, accessories, and attachments: • diamond dressing attachment • magnetic chuck • laminated blocks • fixtures • angular wheel dresser • radius dresser • collet chuck • centres • adhesives • demagnetizer
Select workholding devices, accessories, and attachments by determining: • type • size • function • holding/mounting characteristics • type of wheel • workpiece characteristics • handling, storing, and maintenance Demonstrate contact surface cleaning procedures. Demonstrate magnetizing procedures for permanent or electromagnetic chucks. Demonstrate mounting, positioning, aligning, and securing procedures. Demonstrate procedures for demagnetizing the workpiece.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 33 - © Ontario College of Trades
55.4 Demonstrate mounting, truing, and dressing of grinding wheels. (1 hr)
Demonstrate mounting, truing, balancing, and dressing of wheel. Describe balancing of wheel. Describe safe mounting of wheels on surface or cylindrical grinders. Demonstrate dressing for side grinding or form grinding. Demonstrate use of radius tangent wheel dresser.
55.5 Develop a plan for grinding flat surfaces, tapers, angles, and profiles. (2 hrs)
Select grinding procedures: • surface • plunge • cut off • inside diameter (ID)/outside diameter (OD) • profile • parallel/traverse • external taper
Identify grinder workholding devices and accessories. Select required surface or cylindrical grinder. Describe measuring and checking techniques.
55.6 Perform grinding. (13 hrs)
Describe profile grinding. Describe plunge grinding. Describe angular grinding. Describe combination angle and radius grinding. Demonstrate OD grinding. Demonstrate ID grinding.
Demonstrate taper O/D grinding.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 34 - © Ontario College of Trades
Number: S0656 Reportable Subject: RAM/SINK ELECTRICAL DISCHARGE MACHINING
(EDM) TECHNOLOGY Duration: Total 6 hours Theory 6 hours Practical 0 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0656.1 Describe safety procedures when setting up and operating EDM machines. S0656.2 Describe machine controls, dielectric fluid requirements, and settings of ram/sink type EDM machines. (1 hr) S0656.3 Describe assembly of EDM electrodes and holders. (1 hr) S0656.4 Select ram/sink EDM techniques to spark erode jig and fixture components. (3 hrs) S0656.5 Describe routine maintenance. (1 hr) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
100% 0% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 35 - © Ontario College of Trades
S0656.0 Ram/Sink Electrical Discharge Machining (EDM) Technology Duration: Total 6 hours Theory 6 hours Practical 0 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5275, U5276, U5277, U5278; 630T: U5556, U5557, U5565, U5566, U5567, U5568 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to describe ram/sink EDM procedures for producing jig and fixture components. LEARNING OUTCOMES AND CONTENT 56.1 Describe safe working procedures when setting up and operating EDM
machines. Identify potential safety hazards which may occur during the setting up and
operation of EDM machines.
Demonstrate safe working habits including: • protective clothing • protective equipment and gear • good housekeeping • securing workpiece • stabilizing workpiece • start-up • shut-down • dielectric fluids • excessive heat • lock out procedures • tagging procedures
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 36 - © Ontario College of Trades
56.2 Describe machine controls, dielectric fluid requirements, and settings of ram/sink type EDM machines. (1 hr)
Identify machine controls, dielectric fluid, and operating principles of the EDM by determining: • application • type • workholding devices • dielectric fluid • polarity • table travel • resistance capacity • pulse type • rotary impulse • table axis movements
Describe feed control values and the graduations of micrometer collars.
56.3 Describe the assembly of EDM electrodes and holders. (1 hr)
Describe the machining characteristics of electrode materials: • brass • copper • silver tungsten grades • graphite • premium graphite Identify machining or manual methods to produce electrodes by using: • part product prints • charts • templates Identify the electrode overburn allowances by determining: • electrode material • workpiece material • removal rate Describe flushing techniques. Describe holding requirements. Calculate the wear ratio of the electrode materials. Determine required number of electrodes.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 37 - © Ontario College of Trades
56.4 Select ram/sink EDM techniques to spark erode jig and fixture components. (3 hrs)
Describe machining sequence to spark erode component. Identify the number of electrodes to be used by determining: • amount of material to be removed • electrode material • workpiece material • surface finish • degree of accuracy • flushing conditions Describe overburn.
Describe EDM cutting arc conditions: • shorted arc • D/C arc • open arc • erratic cutting • transistor failure • excessive heat in power supply Describe ram/sink EDM machining procedures to produce a jig and fixture component: • flat • contours • angles • slots • holes • helical shapes • peripheries
56.5 Describe routine maintenance. (1 hr) Describe lubrication and cleaning procedures. Describe dismantling, handling, and storage of tools, tooling, workholding devices, and measuring instruments.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 38 - © Ontario College of Trades
Number: S0657 Reportable Subject: MACHINING CENTRE COMPUTERIZED NUMERICAL CONTROL (CNC) TECHNOLOGY Duration: Total 24 hours Theory 12 hours Practical 12 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0657.1 Describe safe working procedures when
setting up and operating CNC machining centres.
S0657.2 Describe operating principles and applications of CNC machining centres. (1 hr)
S0657.3 Describe the basics of CNC dimensioning. (2 hrs) S0657.4 Describe part programming methods, set-up
sheets, tooling lists, part program manuscripts, and input media. (4 hrs)
S0657.5 Describe manual operation systems for CNC machining centres. (2 hrs)
S0657.6 Develop a plan for a CNC machining centre. (2 hrs) S0657.7 Demonstrate procedures for entering and
verifying a program for a CNC machining centre to perform linear and circular machining exercises. (13 hrs)
Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
50% 50% 100%
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 39 - © Ontario College of Trades
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 40 - © Ontario College of Trades
S0657.0 Machining Centre Computerized Numerical Control (CNC) Technology
Duration: Total 24 hours Theory 12 hours Practical 12 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5274, U5276, U5277, U5278; 630T: U5556, U5557, U5564, U5566, U5567, U5568 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to read and interpret CNC documentation; and demonstrate procedures for entering and verifying a CNC program for drilling, linear interpolation, and circular interpolation. LEARNING OUTCOMES AND CONTENT 57.1 Describe safe working procedures when setting up and operating CNC
machining centres.
Identify potential safety hazards which may occur during the setting up and operating of CNC machining centres. Demonstrate safe working habits including: • protective clothing • protective equipment and gear • good housekeeping • operating procedures • start-up • shut-off • securing workpiece/machine-tools • stabilizing workpiece/machine-tools • lubricants • lock-out procedures • tagging procedures
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 41 - © Ontario College of Trades
57.2 Describe operating principles and applications of CNC machining centres. (1 hr)
Identify types of CNC machining centres: • vertical • horizontal • multi-axis
Describe the capabilities of CNC machining systems: • types of equipment • editing capability • program path ability • processing power • high speed machining
Identify the operating principles and applications of CNC machining centre controls:
• CNC controls • tapeless control • PC/DNC systems • conversational programming Describe the major features and functions of machining centres: • CPU • input devices • tool changer • work envelope • holding devices • safety interlocks • engineering drawing • CNC part program • input media • CNC machine tool • finished part • repeatability Describe the common means of producing part program files: • manual programming • CAM systems • conversational programming
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 42 - © Ontario College of Trades
57.3 Describe the basics of CNC dimensioning. (2 hrs)
Describe the Cartesian Coordinate System: • quadrant notation • point location in XY plane • point location in XYZ plane
Describe machine tool axis designations: • primary linear axis • secondary linear axis • primary rotary axis • secondary rotary axis • right hand rule • axis orientation Describe machine zero point locations: • fixed zero points • full zero shift • floating zero
Determine set-up point locations to establish: • machine home position • absolute zero position • Z axis touch off points Describe CNC machining centre capabilities of positioning and contouring: • linear interpolation • circular interpolation
Describe use of dimensioning practices: • baseline dimensioning (datum) • relative (chain) dimensioning Select coordinate systems for CNC machining centres: • type of machine • axis designation • typical specifications
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 43 - © Ontario College of Trades
57.4 Describe part programming methods, set-up sheets, tooling lists, part program manuscripts, and input media. (4 hrs)
Identify documentation used for the CNC machining process: • set-up sheet • tooling list • part program manuscript • input media
Describe the individual components of a part program manuscript: • sequence numbers • preparatory functions • miscellaneous functions • axis motions • feed rates • spindle speeds • tool numbers Describe additional word and block structures that exist within the part program code: • decimal point programming • block delete • comments
Describe the components of a set-up sheet: • part zero position • part location • clamp • fixture locations Describe the components of a tooling list: • tool type • tool number • diameter offset number • tool length offset number Describe the methods of producing part program files: • CAM systems • manual programming • conversational programming
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 44 - © Ontario College of Trades
57.5 Describe manual operation systems for CNC machining centres. (2 hrs)
Describe manual program interruption: • single block operation • feedhold • emergency stop Describe manual data input (MDI): • line command execution • set-up applications
Describe program data override: • rapid motion override • spindle speed override • feedrate override • dry run operation • manual absolute setting • practical applications Describe interfacing to peripherals: • RS-232C Interface • PC/DNC • USB • wireless
57.6 Develop a plan for a CNC machining centre. (2 hrs)
Interpret documentation to determine: • workpiece material specifications • method of routing instructions • special fixturing requirements Plan sequence of machining by identifying: • order of machining • tooling selection • workpiece set-up
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 45 - © Ontario College of Trades
57.7 Demonstrate procedures for entering and verifying a program for a CNC machining centre to perform linear and circular machining exercises.
(13 hrs)
Demonstrate the use of preparatory commands (G-codes): • modality of G-codes • recognize conflicting commands • order in a block
Demonstrate the use of M-codes:
• typical M-codes • M-codes in a block
Demonstrate the use of codes to specify dimensions: • metric/inch selection • absolute data input - G90 • incremental input - G91 • combination in the same program • radius programming
Demonstrate the use of codes to specify speeds and feeds: • spindle rotation direction • spindle stop • spindle orientation • spindle speed (RPM) • feedrate function • feedrate control • feedrate per minute • feedrate override and feedhold • feedrate override and functions
Demonstrate the use of codes to specify:
• tool number • tool length offset • tool radius offset.
Demonstrate the use of codes to establish reference points:
• machine reference point • manufacturers’ setting • workpiece reference point • tool reference point • position register command-G54 • fixture offsets
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 46 - © Ontario College of Trades
57.7 Continued Demonstrate the use of common machine function controls:
• mode selector • rapid, feedrate, and spindle overrides • single block • manual feed functions • soft keys • offset registers
Demonstrate the use of codes to produce a part.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 47 - © Ontario College of Trades
Number: S0658 Reportable Subject: TOOLING TECHNOLOGY (JIGS AND FIXTURES) Duration: Total 12 hours Theory 7 hours Practical 5 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0658.1 Describe rationale for using jigs and fixtures when manufacturing components. (1 hr) S0658.2 Describe types and classifications of jigs. (2 hrs) S0658.3 Describe types and classifications of fixtures. (2 hrs) S0658.4 Describe jig and fixture tooling. (3 hrs) S0658.5 Describe jig and fixture design characteristics.
(4 hrs) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
55% 45% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Basic and Advanced Tool and Die Making Jig & Fixture Making for Metal Working
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 48 - © Ontario College of Trades
S0658.0 Tooling Technology (Jigs and Fixtures) Duration: Total 12 hours Theory 7 hours Practical 5 hours Cross-Reference to Training Standards: 430A: U5276, U5277, U5278, U5279; 630T: U5566, U5567, U5568, U5569 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to describe jig types and classification, fixture types and classification, and operational principles and design characteristics of jigs and fixtures. LEARNING OUTCOMES AND CONTENT 58.1 Describe rationale for using jigs and fixtures when manufacturing components. (1 hr) Describe the rationale for using jigs and fixtures when manufacturing components:
• advantages • disadvantages
58.2 Describe types and classifications of jigs. (2 hrs) Identify types of jigs:
• template • plate • sandwich • channel • closed (box, leaf, tumble) • angle plate • indexing
Describe jig classifications: • drilling • boring
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 49 - © Ontario College of Trades
58.3 Describe types and classifications of fixtures. (2 hrs) Identify types of fixtures:
• plate • angle plate • vise jaw • indexing • assembly
Describe fixture classifications:
• milling • turning • boring • grinding • welding • inspection
58.4 Describe jig and fixture tooling. (3 hrs)
Describe jig and fixture tooling components: • tooling bodies • bushings • stop blocks • locators • supports • clamping devices • ejectors • arbors • mandrels • vises • magnetic chucks • keys • fasteners • springs • pads • feet • plugs • pins
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 50 - © Ontario College of Trades
58.5 Describe jig and fixture design characteristics. (4 hrs)
Describe jig and fixture characteristics: • planes • reference surfaces and points • workpiece location • locators
S fixed S adjustable
• supports S fixed S adjustable • clamps
S strap S screw S cam S toggle S wedge
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 51 - © Ontario College of Trades
Number: S0659 Reportable Subject: TOOLING ASSEMBLY TECHNOLOGY FOR JIGS &
FIXTURES Duration: Total 18 hours Theory 6 hours Practical 12 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0659.1 Describe safe working habits when
assembling tooling components. S0659.2 Identify set-up equipment and attachments
used for fitting, positioning, and aligning tooling components. (3 hrs)
S0659.3 Describe the assembly of keyed components. (4 hrs)
S0659.4 Describe the assembly of dowelled components. (5 hrs)
S0659.5 Describe final assembly processes and techniques. (6 hrs)
Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
30% 70% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Technology of Machine Tools Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 52 - © Ontario College of Trades
S0659.0 Tooling Assembly Technology for Jigs & Fixtures Duration: Total 18 hours Theory 6 hours Practical 12 hours Cross-Reference to Training Standards: 430A: U5276. U5277, U5278, U5279; 630T: U5566, U5567, U5568, U5569 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to describe fitting and assembly techniques and plan the assembly of tooling components. LEARNING OUTCOMES AND CONTENT 59.1 Describe safe working habits when assembling tooling components. Identify potential safety hazards which may occur during tooling assembly
procedures.
Demonstrate safe working habits including: • protective clothing • protective equipment and gear • good housekeeping • start-up • shut-down • securing workpiece/cutting tool • stabilizing workpiece/cutting tool • lubricants • hand and power tools • material handling equipment
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 53 - © Ontario College of Trades
59.2 Identify set-up equipment and attachments used for fitting, positioning, and aligning tooling components. (3 hrs)
Describe the application of equipment and attachments used for fitting, positioning, and aligning components: • lathes • mills • grinders • hones • jig borers • jig grinders • mandrels • vises • angle plates • sine bars • grinding chucks • files • reamers • stones
59.3 Describe the assembly of keyed components. (4 hrs) Describe the operating principles and design parameters for using keys in
assemblies. Describe the required keyed assemblies by identifying:
• application • design characteristics • components • types • sizes • fasteners • clearances • tolerances
Describe the keyed assembly process by determining:
• types of tools and equipment • sizes of tools and equipment • locations of components • relative positions of components • sequence of assembly • lubricants • key fits • workholding requirements • measuring and checking equipment
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 54 - © Ontario College of Trades
59.3 Continued Identify the types of keyed component assemblies:
• plain taper • gib head taper • square • rectangular • feathered • woodruff
59.4 Describe the assembly of dowelled components. (5 hrs) Describe the operating principles and design parameters of dowelling assemblies.
Describe the required dowel assemblies by identifying: • application • design characteristics • components • types • sizes • fits Describe the dowelled assembly process by determining: • types and sizes of tools and/or equipment • locations and relative positions of components • number of dowel pins • sequence of assembly • use of lubricants • dowel fits • workholding requirements Identify the type of pins used in assemblies: • dowelled • roll pin • tapered • groove
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 55 - © Ontario College of Trades
59.5 Describe final assembly processes and techniques. (6 hrs)
Describe types of fit: • running • sliding • locational • interference • clearance Describe the operating principles and design parameters of fits used in the assembly process. Describe the type of fit by identifying: • applications • design characteristics • clearances • tolerances • sizes • allowances • surface finish
Describe the assembly process by determining: • types and sizes of tools/equipment • locations and relative positions of components • sequence of assembly • use of lubricants • pressing and guiding requirements • heating or freezing media • workholding requirements Describe the assembly of components.
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 56 - © Ontario College of Trades
Number: S0660 Reportable Subject: JIG AND FIXTURE BUILDING Duration: Total 63 hours Theory 23 hours Practical 40 hours Prerequisites: L1 CC: S0601, S0602, S0603, S0604, S0605, S0606, S0607, S0608, S0609, S0610, S0611 Content: S0660.1 Interpret engineering, CAD data, part
drawings, component prints, assembly, jig, and fixture prints. (3 hrs)
S0660.2 Interpret documentation. (2 hrs) S0660.3 Demonstrate detailed sketching of a
component from engineering drawings and CAD data.
(6 hrs) S0660.4 Identify jig and fixture materials. (2 hrs) S0660.5 Develop a plan for the jig and fixture building
process. (4 hrs) S0660.6 Demonstrate the machining, fitting, and
assembling of jig and fixture components. (25 hrs) S0660.7 Demonstrate jig and fixture assembly
procedures. (24 hrs) Evaluation & Testing: Assignments related to theory and application skills Minimum of one mid-term test during the term Final test at end of term Periodic quizzes Mark Distribution:
Theory Testing
Practical Application Testing
Final Assessment
40% 60% 100%
Instructional and Delivery Strategies: Lecture Video Paper based material CBT Internet On-Line Reference Materials: Shop Text Books Jig & Fixture Making for Metal Working Basic and Advanced Tool and Die Making
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 57 - © Ontario College of Trades
S0660.0 Jig and Fixture Building Duration: Total 63 hours Theory 23 hours Practical 40 hours Cross-Reference to Training Standards: 430A: U5266, U5267, U5268, U5269, U5270, U5271, U5272, U5273, U5274, U5275, U5276, U5277, U5278, U5279; 630T: U5555, U5556, U5557, U5558, U5559, U5560, U5561, U5562, U5563, U5564, U5565, U5566, U5567, U5568, U5569 GENERAL LEARNING OUTCOMES Upon successful completion the apprentice is able to demonstrate jig and fixture component building; and perform fitting and assembly techniques. LEARNING OUTCOMES AND CONTENT 60.1 Interpret engineering and part drawings, CAD data, component prints,
assembly, jig, and fixture prints. (3 hrs) Interpret engineering drawings and CAD data to determine tooling construction procedures. Interpret part prints to identify dimensional sizes, tolerances, limits, finish
condition, and material type. Identify jig and fixture component features with engineering drawings and CAD
data: • tool bodies • bushings • pins • clamps • fasteners • keys • springs • locators
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 58 - © Ontario College of Trades
60.2 Interpret documentation. (2 hrs)
Interpret elements and features of engineering drawings and CAD data to determine: • clearances • slide travel • size • dimensions • tolerances • finishes • assembly
Interpret tables and charts to determine clearances, shapes, and dimensions. Interpret job specifications to determine the required clearances, fits, tolerances, and assembly methods. 60.3 Demonstrate detailed sketching of a component from engineering drawing
and CAD data. (6 hrs)
Develop sketches from piece-part specification for jig and fixture component details which includes: • shape • dimensions • tolerances • finishes
60.4 Identify jig and fixture materials. (2 hrs) Interpret engineering drawings and CAD data to identify materials by determining:
• type • grade • dimensions • surface condition • hardenability • heat-treatment
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 59 - © Ontario College of Trades
60.5 Develop a plan for the jig and fixture building process. (4 hrs)
Develop a jig and fixture build plan that identifies: • machine tools • machining procedures • machining processes • machine accessories • tooling aids • jig and fixture building sequence • fitting and assembly procedures • fabrication processes
60.6 Demonstrate the machining, fitting, and assembling of jig and fixture
components. (25 hrs)
Identify machining methods and attachments to be used in the fabrication of jig and fixture components: • turning • milling • surface grinding • cylindrical grinding • jig boring • jig grinding
Select workholding devices:
• grinding mandrel • precision vises • angle plates • sine bars • grinding chucks
Demonstrate the fabrication of jig and fixture components by:
• turning • milling • surface grinding • cylindrical grinding • jig boring
Demonstrate fitting, positioning, and aligning of components:
• running • sliding • locational • interference • clearance fits
TOOL AND DIE MAKER – TOOL/TOOLING MAKER - LEVEL 2
- 60 - © Ontario College of Trades
60.7 Demonstrate jig and fixture assembly procedures. (24 hrs) Identify the sequence of sub and final assembly. Perform holding and aligning of mating jig and fixture components. Perform the lay out, fit, and fastening of jig and fixture components. Perform the lay out, fitting, and fastening of jig and fixture sub-assemblies for
final assembly. Demonstrate the final assembly using completed sub-assemblies. Demonstrate procedures for testing, modifying, and adjusting of jig and fixture
assemblies. Identify the accuracy and mechanical functioning of jig and fixture assemblies.
top related