AC-47 Gunship interior S.A. 49 736 - Eduard · 1/4 49 736 ac-47 gunship interior s.a. 49 736 original kit parts pŮvodnÍ dÍly stavebnice photo-etched parts leptanÉ dÍly parts
Post on 27-Jul-2020
0 Views
Preview:
Transcript
1/4 49 736
AC-47 Gunship interior S.A.49 736
ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM
1 COLORED ETCHED PARTSLEPTANÉ BAREVNÉ DÍLY
1 ETCHED PARTSLEPTANÉ NEBAREVNÉ DÍLY
1 ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICE
detail set for 1/48 REVELL No. 04926 kit • sada detailů pro stavebnici 1/48 REVELL No. 04926
13,20
116
6
5
5
2 pcs.
18
kit part 3623
2 pcs.
2 pcs.
1617
19
36
kit part 36
20
13
kit part 36
kit part 34
kit part 34
37
27
2/4 49 736
2 pcs.
3 pcs.
22
32
24
35
kit part 68
2 pcs.
48
4
kit part 18
kit part 71
30 kit part 71
kit part 72
3410
12
1531
14
43
kit part 7240
42
41
41
51
49
2 sets
kit parts 203L,203R,204
40
42
41
41
53
kit parts 94 38 2
7
kit parts 94 38
A
kit parts 94 38
1
7
2829
3
50
A
do not use kit part 69
3/4 49 736
© EDUARD M.A. 2015 www.eduard.com Made in Czech Republic
2
1
3
kit part 70
l - 4mm
kit part 67
2 pcs. 52
54
kit part 67
2 pcs.
2 pcs.
46
46
47
47
38
39
45
26
2 pcs. 58
kit part 37
55
55
kit part 202
56
57
4444
3 sets
25
kit part 1
kit part 2
21
33
8
9
kit parts 1 2
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na části dílů, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will be permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne až po přimáčknutí, před přimáčknutím lze dílem opatrně manipulovat.
PARTS WITH GLUE DÍLY OPATŘENÉ LEPIDLEM
4/4 49 736
top related