Transcript
8/3/2019 2 - 4 Electrical Practical
http://slidepdf.com/reader/full/2-4-electrical-practical 1/6
TRAINING DEPARTMENT
College /Polytechnic
SyllabusYear
Branch Sem (x) IPT Session ID(xx)
Training Ref Number (xxx)
C 09 E 3 0 2 0 0 4
1) To execute Stair case wiring for G + 3 floors.
2) To prepare a wiring circuit to check the availability of R/Y/B phases using onelamp only by operating individual switches for each phase and test it.
3) To control 3 bells in series to ring together when any one of the 3 push button is pressed. (Emergency alarm circuit).
4) To connect a Single Phase Main Switch, Single Phase DOL Starter, and MCB(Miniature Circuit Breaker) to a Single phase motor load and run it.
5) To connect a 3 phase Main Switch, Star / Delta Starter, and ELCB (Earth LeakageCircuit Breaker) to a 3 phase motor load and run, with a provision for arrangement to trip the ELCB when a fault occurs.
6) To connect a 3 phase TPN main switch, 3 phase 4 way DB with a suitable load.
7) To prepare of Service Mains with single phase Energy Meter, Cutout, mainswitch, 4 way DB, indicator lamp, terminated with 3 sub-circuit mains.
8) To prepare a wiring circuit for connecting Sodium Vapour lamp and MercuryVapour lamp with single phase supply.
9) To execute a Fluorescent Tube light connection with Electronic Choke and test it,also measure the voltage across the tube light fitting.
10) To construct a simple model to know the working of Neon Tube circuit used inadvertising (With minimum 3 blocks).
11) To prepare a testing board to test electrical appliances with a necessary series, parallel supply provision, and indicator lamp, fuse unit.
13/03/13 1:53 a3/p3 1
8/3/2019 2 - 4 Electrical Practical
http://slidepdf.com/reader/full/2-4-electrical-practical 2/6
TRAINING DEPARTMENT
Winding To wind 230/12-0-12 volt, 500 ma transformer and test it.To design and wind No Volt Coil used in starter.To wind and insert the starting / running coils of a Single phase induction motor, for a
minimum of one pole.To wind and insert stator coils of a 3 phase induction motor (Single layer / Double
Layer), for a minimum of one pole.To give end connection for a 3 phase induction motor winding for a 2 pole / 4 pole
operations and run it. Measure the rotor speed, starting current and running current.To wind and insert the coils for ceiling fan motor (minimum 2 coils).
Electrical machines
Electrical machines are energy converters. If the machine input is mechanicalenergy and the output electrical energy then that machine is a generator,as shown in Fig. (a) .
Alternatively, if the machine input is electricalenergy and the output mechanical energy then the machine is a motor, asshown in Fig. (b)
An electrical machine may be used as a motor or a generator, although in
practice the machine will operate more effi ciently when operated in themode for which it was designed.
Simple a.c. generator or alternator
If a simple loop of wire is rotated between the poles of a permanent magnet, between thenorth and south poles. This fl ux cutting will induce an emf in the wire by Faraday’s law which states that when a conductor cuts or
13/03/13 1:53 a3/p3 2
8/3/2019 2 - 4 Electrical Practical
http://slidepdf.com/reader/full/2-4-electrical-practical 3/6
TRAINING DEPARTMENT
is cut by a magnetic fi eld, an emf is induced in that conductor . If the generatedemf is collected by carbon brushes at the slip rings and displayedon the screen of a cathode ray oscilloscope, the waveform will be seen to
be approximately sinusoidal. Alternately changing, fi rst positive and thennegative, then positive again, giving an alternating output.as shown in below fig., the loop of wire will cut the lines of magnetic flux
Simple d.c. generator or dynamo
If the slip rings of Fig. are replaced by a single split ring, called a commutator,the generated emf will be seen to be in one direction, as shownin Fig below . The action of the commutator is to reverse the generated emf every half-cycle, rather like an automatic change-over switch. However, this simple
arrangement produces a very bumpy d.c. output. In a practicalmachine, the commutator would contain many segments and many windingsto produce a smoother d.c. output. Similar to the unidirectional batterysupply shown in below fig
13/03/13 1:53 a3/p3 3
8/3/2019 2 - 4 Electrical Practical
http://slidepdf.com/reader/full/2-4-electrical-practical 4/6
TRAINING DEPARTMENT
13/03/13 1:53 a3/p3 4
8/3/2019 2 - 4 Electrical Practical
http://slidepdf.com/reader/full/2-4-electrical-practical 5/6
TRAINING DEPARTMENT
13/03/13 1:53 a3/p3 5
8/3/2019 2 - 4 Electrical Practical
http://slidepdf.com/reader/full/2-4-electrical-practical 6/6
TRAINING DEPARTMENT
Domestic Installers Workshop Course Content:
Ring main circuits (sockets)
Basic lighting circuits
2 way lighting circuits
2 way lighting and intermediate circuits
Radial power circuits (cooker points etc)
Earthing and bonding procedures
Zoning and selection of equipment
Selecting cable sizes and calculating load demands
Introduction to electrical regulations
Health & safety
Safe Isolation procedures
Identifying Three Phase Systems
Electrical calculations
13/03/13 1:53 a3/p3 6
top related