07MY Rav4(RHD) Installation Manual - Toyota-Tech.eu
Post on 26-Apr-2022
4 Views
Preview:
Transcript
VEHICLE SECURITY SYSTEMINSTALLATION INSTRUCTION
PART NUMBER
FOR : A*A30R-AW*G*W
TOYOTA MOTOR CORPORATION
RAV4 (RHD)
SECURITY KIT
08586-4A921FITTING KIT
1 07-2007
Precautions
2 07-2007
Fitting Kit Contents (08586-4A921)
[1] [2] [3]
[4] [5]
[6] [7] [8]
[6]
[1]
[2]
[3]
[4]
Pos. No. Q'tyDescription
1
1
1
1
[5]
2
[8]
Wire Harness
ECU Mounting Bracket
GLASS BREAKAGE CONTROL UNIT
Microphone
Bolt (M6x18)
Small Foam Tapes
Splicing Connector
1
[7] Wire Ties (150mm) 4
1
3 07-2007
Vehicle DisassemblySet the seat cover and floor mat before starting operation. Be careful do not scratch anddamage the vehicle.
1. Remove the luggage cover.
2. Remove the floor board.
3. Remove the floor box (A).
Luggage Cover
Fig. 1
Fig. 2
Fig. 3
Floor Board
Clips (x4)
Clips (x2)
Floor Box (A)
4 07-2007
Fig. 6
Fig. 5
5. Fold down driver and passenger rear seat back.
6. Remove the floor box (B).
7. Remove the driver side rear door scuff plate.
8. Pull up the driver side weather strip.
Rear Door Scuff Plate
Clips (x2)Weather Strip
Rear Seat Back
4. Remove the deck trim cover.
Clips (x6)
Deck Trim Cover
Fig. 4
Clips (x3)
Clips (x2)
Clips (x2)Floor Box (B)
Screws (x2)
Screws (x2)
5 07-2007
Fig. 8
12. Remove the seat belt anchor.
13. Remove two screws from the luggage side trim.
Fig. 7
9. Remove two hooks from the luggage side trim.
10. Remove the seat fold down lever cover.
11. Pull up the weather strip.
Luggage Side Trim
Hook
Hook
Bolt
Bolt
CoverClips (x2)
Clips (x2)
Weather Strip
Seat Fold DownLever Cover
Bolt
Cover
Fig. 9
14. Remove the driver side luggage side trim.
Claw (x4)
Clips (x5)
Luggage Side Trim
Screws (x2)
Luggage Side Trim
6 07-2007
Fig. 10
15. Remove front door scuff plate.
Fig. 11
12. Remove the seat belt anchor.
13. Remove the center pillar cover.
Fig. 12
14. Remove the clip from the cowl cover.
15. Remove the cowl cover.
Front Door Scuff Plate
Clips (x3)
Bolt
Cover
Clips (x4)
Clips (x2)
Clips (x2)
Clip
Center Pillar Cover
Cowl Cover
7 07-2007
GBS ECU/ Microphone and Wire Harness InstallationSet the seat cover and floor mat before starting operation. Be careful do not scratch anddamage the vehicle.
1. Turn the GBS adjustment screw on the GBS ECU to the "8" position.
Fig. 13
GBS ECU
Mounting Bracket
GBS ECU
Fig. 14
2. Insert the mounting bracket into the indicated bracket slot on the GBS ECU.
Insert the mounting bracket into thecorrect ECU's slot.
Cut!
Fig. 15
Small Foam Tape
Small Foam Tape(Half Cut)
3. Cut the small foam tape in half, then wrap it to the microphone harness as shown.
7 07-2007
Fig. 16
4. Install GBS ECU using the supplied kit's bolt, then install the GBS ECU to the driver side rear luggagearea as shown.
5. Use the existing vehicle bolt to secure the TVSS harness' the ground terminal.
6. Secure the TVSS harness's root of the ground terminal on vehicle harness with TVSS Wire Tie.
7. Route the TVSS harness toward the GBS ECU, Securing it to the vehicle harness with 2 wire ties.
8. Connect the TVSS harness' 8P white connector to GBS ECU.
9. Connect the TVSS harness' 2P white connector to microphone.
Press the microphone to the bracket firmly.
10. Secure the TVSS harness to vehicle harness with 3 wire ties.
11. Route the TVSS harness toward rear door scuff plate.
Bracket
Marker LineMicrophone
TVSS Harness
Wire TieBolt
Bolt
GBS ECU
TVSS Harness'8P
Wire Ties
Wire Ties (x3
TVSS Harness' 2PConnector (White)
Ground
8 07-2007
1
2
3
4
12. Route the TVSS harness toward therear door scuff plate , Securing it to thevehicle harness with 4 wire ties.
Fig. 17
Wire Ties (x4)
Fig. 18
Wire Ties (x2)
13. Route the TVSS harness toward thecenter pillar , Securing it to the vehicleharness with 2 wire ties.
Fig. 19
14. Route the TVSS harness toward thefront door scuff plate, Securing it to thevehicle harness with 2 wire ties.
Wire Ties
9 07-2007
Fig. 20
15. Route the TVSS harness toward thedriver's side cowl cover , Securing it to thevehicle harness with 4 wire ties.
Wire Ties
16. Remove vehicle's 16p connector from cowl side J/B
Fig. 21
Fig. 22
Vehicle's 16PConnector
Fig. 21
17. Locate the Vehicle's 16p connector'spink wire(2nd row, 3rd space from theleft). Attach the TVSS harness's pink wirewith splicing connector.
Vehicle's 16PConnector
Pink Wire
Splicing Connector Vehicle's Pink
Wire
TVSS's PinkWire
10 07-2007
REFIT THE REMOVED PARTS.
Fig. 23
18. Remove Vehicle's 14p connector fromcowl side J/B
19. Connect the TVSS 14p connector tothe Vehicle's 14p connector.
20. Secure the TVSS connector to vehicleharness with 1 wire tie.
Wire Tie
Vehicle's14P
TVSS 14PConnector
TVSS 14PConnector
Vehicle's14P
Fig. 24
11 07-2007
Accessory Function CheckChecklist - these points MUST be checked to ensure a quality installation.
Check: Look For:
The horn stops sounding.All the lights stop flashing and/ or turn off.The status monitor’s LED turn off, but animmobilizer’s LED remains on.
Insert the key into the driver’s door keycylinder and turn it toward the back of thevehicle to stop the alarm.
Fit the appropriate fuse before beginning.Close the hood before beginning.
Press and release the remote control’s lockbutton to start the system’s arming process.
The tail and marker lights flash once.The buzzer chirps once.All doors lock.The Security LED lights up.
Wait 30 seconds. After 30 seconds, the security indicator startsflashings; the system is now armed.
With the tip of key, tap the centerof the rear window to trigger the"warn away" alarm.
The horn sounds repeatedly.The interior lights turn on.The headlights flash repeatedly.The tail and marker lights flash repeatedly.The Security LED lights up.
9 07-2007
top related