YOU ARE DOWNLOADING DOCUMENT

Please tick the box to continue:

Transcript
Page 1: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

The process of Machining and Assembly of Engine

刘洋 Liu Yang

1251886

Page 2: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

The Main Part of Engine

(1) Cylinder block(2) Cylinder head (3) Connecting rod(4) crank shaft(5) Camshaft

So, how to make these parts? That’s talk about it.

Page 3: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.
Page 4: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

Cylinder BlockMaterial: gray cast iron, alloy cast iron, aluminum alloy, vermicular

cast iron and so on.Method of processing :(1) The processing of big plain: first, simple milling and then, accurate milling.(2) The processing of the bearing hole of the main shaft:

accurate boring using the multi-knife and the pull boring bar. The hole should be finished at only one time in order to make sure the vertical degree of the hole and thrust plain.

(3) The processing of the cylinder hole: simple boring, semi- accurate boring, accurate boring.

Page 5: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.
Page 6: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

Cylinder head

Material: gray cast iron, alloy cast iron, aluminum alloyMethod of processing: Since the requirement of accuracy is very high, and

take the difficulty into consideration, today, the company using the machining center manufacturing technology, manufacturing technology and other agile production line manufacturing technology to produce the cylinder head.

Page 7: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.
Page 8: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

Connecting rodMaterial: medium carbon steel, medium carbon alloy steel, powder

metallurgy, high-strength aluminum alloy and so on.Method of processing: (1) Blank: using the CAD\CAM technology to make the high quality

mould in order to maintain the high accuracy at the weight and the thickness of the blank. Then cast.

(2) Mechanical processing: first, take the processing on the end edge, using the

methods of grinding. Then treating the surface of combination. Finally, processing on the holes of the big edge and the small edge, using the methods of drilling and boring.

Page 9: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.
Page 10: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

Crank shaft

Material: Nodular cast iron, alloy steel.Method of processing: first, casting the blank. After the heat

treatment, we have to mill the two ends. Then, drill the center hole of the main shaft. After that, lathe the main journal and drill them. Finally, check the crank shaft.

Page 11: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.
Page 12: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

Camshaft

Material: nodular cast iron, alloy cast iron, chilled cast

iron, medium carbon steel, alloys steel.Method of processing: milling the end edge, lathing the main

journal, heat treatment, check, and then grind the cam and the journal.

Page 13: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.
Page 14: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

The process of Assembly

Before the assembly: we should pay attention to the following

points:(1) All the parts should be checked and conform to

the requirement.(2) All the parts should be cleaned and dried.(3) The part cannot be exchanged.(4) All the parts should be assembled correctly

according to the assembly drawing.

Page 15: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

The installation process (1) Install the cylinder (2) Install the crack shaft and the flywheels(3) Install the pistons and the connecting rod(4) Install the parts of the valve (5) Install the camshaft(6) Install the cylinder head(7) Install other parts, such as the pipe, the pump

and the belt.

Page 16: The process of Machining and Assembly of Engine 刘洋 Liu Yang 1251886.

Related Documents