Top Banner
XT500/XR100 HARWARE AND INSTALLATION Slide 1 XR500/XR100 Basic Training Hardware & Installation ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ Slide 2 Objectives After completing this course you will: 1) Perform a site evaluation 2) Understand the discipline of wiring 3) Install system hardware 4) Correctly wire the panel, keypads and system accessories 5) Address DMP keypads and expanders on the system 6) Achieve line seizure of the panel phone line 7) Pass the necessary exams to obtain your DMP Certificate of Completion for this course. ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ Slide 3 Basic Tools Installer friendly Basic tools needed for install – List ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________
32

XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

Mar 13, 2021

Download

Documents

dariahiddleston
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 1 XR500/XR100 Basic Training

Hardware & Installation

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 2 Objectives

After completing this course you will:– 1) Perform a site evaluation– 2) Understand the discipline of wiring– 3) Install system hardware– 4) Correctly wire the panel, keypads and system

accessories– 5) Address DMP keypads and expanders on the

system– 6) Achieve line seizure of the panel phone line– 7) Pass the necessary exams to obtain your DMP

Certificate of Completion for this course.

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 3 Basic Tools

• Installer friendly• Basic tools needed for install

– List

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 2: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 4 Site Evaluation

• Evaluate site and establish work plan– Site walk through– Consider location of various components

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 5 Panel Ground

• Terminal 4 grounding• Cold water pipe

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 6 Wire Routing

• Part of site evaluation is wire routing• While exploring site look for “pitfalls” and trouble

spots• Suitable locations for devices

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 3: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 7 Pre-drilling

• Pre drill before pulling wire– Door jambs, top plates, ceilings

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 8 Wire Type and Distances

• Wire type and distance– 18 or 22 AWG unshielded– DO NOT use twisted pair

• Maximum bus distance– 710 modules

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 9 Keeping Documentation

• Documentation– Finish site evaluation, then document the install– Programming sheet is supplied– Write down as much information as possible

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 4: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 10 Pulling Wire

• Pulling wire– Backbone of the system– Label wiring

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 11 Wire Tagging

• Wire tagging– Label or mark each wire pulled– One label on wire, matching label on box

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 12 Multiple Pulls

• Multiple pulls– Pay attention to labels– Consequences could be great

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 5: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 13 Documentation

• Documentation– Write down tag numbers – Wiring the panel will go faster– Keep at site for service

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 14 Pulling Spare Wires

• Pulling Spare Wires on difficult pulls– Use a spare wire or consider a wire with multiple

conductors– Save time later for expansion

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 15 Mounting the Enclosure

• Mounting the Enclosure– Dry and secure– Protected from tampering and elements

• Install tip on enclosure

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 6: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 16 Mounting Keypads*

• Mounting Keypads– Base and faceplate

• How to install-4 steps

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 17 Mounting Expanders

• Mounting Expanders– Molded housing with removable cover

• Cover contains module• 711 contained in base• Expanders include color coded wiring harness• Note on 718T

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 18 Pre-Install Review

The next 7 slides are a review for the Pre-Install Section

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 7: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 19 Question 1

1) The purpose of a site evaluation is to establish ______________________________.

A. all of theseB. a work planC. equipment placementD. familiarity with the site

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 20 Question 1

1) The purpose of a site evaluation is to establish ______________________________.

A. all of theseB. a work planC. equipment placementD. familiarity with the site

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 21 Question 2

2) Before pulling any wire, be sure to _______________________________.

A. all of theseB. pre-drillC. mark the wireD. document wire numbers

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 8: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 22 Question 2

2) Before pulling any wire, be sure to _______________________________.

A. all of theseB. pre-drillC. mark the wireD. document wire numbers

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 23 Question 3

3) To provide proper transient protection, terminal ____ must be connected to earth ground using ____ gauge or larger wire.

A. 4, 14B. 4, 18C. 10, 14D. 4, 22

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 24 Question 3

3) To provide proper transient protection, terminal ____ must be connected to earth ground using ____ gauge or larger wire.

A. 4, 14B. 4, 18C. 10, 14D. 4, 22

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 9: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 25 Question 4

4) The panel enclosure must be mounted with the PCB removed.

TrueFalse

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 26 Question 4

4) The panel enclosure must be mounted with the PCB removed.

TrueFalse

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 27 Question 5

5) On long or difficult to access LX-Bus or keypad bus runs, it's a good idea to ________________.

A. take a break B. pull the wire backwardsC. pull a spare wire D. get someone else to help

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 10: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 28 Question 5

5) On long or difficult to access LX-Bus or keypad bus runs, it's a good idea to ________________.

A. take a break B. pull the wire backwardsC. pull a spare wire D. get someone else to help

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 29 Question 6

6) Use no more than ____ feet of 16 gauge or ____ feet of 18 gauge wire between the transformer and the panel.

A. 40, 70 B. 70, 40C. 18, 22D. 2500, 500

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 30 Question 6

6) Use no more than ____ feet of 16 gauge or ____ feet of 18 gauge wire between the transformer and the panel.

A. 40, 70 B. 70, 40C. 18, 22D. 2500, 500

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 11: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 31 Question 7

7) Maximum cumulative distance for LX-Bus and keypad bus circuits is __________, regardless of wire gauge.

A. 500 feetB. 15,000 feetC. 2,500 feet D. 4,000 feet

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 32 Question 7

7) Maximum cumulative distance for LX-Bus and keypad bus circuits is __________, regardless of wire gauge.

A. 500 feetB. 15,000 feetC. 2,500 feet D. 4,000 feet

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 33 Control Panel Wiring

• Control Panel Wiring– Evaluation is complete

• Simple to wire, wiring diagram inside enclosure

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 12: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 34 AC Terminals 1 & 2

• AC Terminals 1 & 2– Connecting supplied transformer– Wire length limitations

• Note on grounding

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 35 Earth Ground

• Earth Ground– Proper ground is essential– Cold water pipe or ground rod

• Note on electrical grounds

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 36 Battery Terminals 3 & 4

• Battery Terminals – Connecting the battery with supplied leads– 318 Battery harness– Replacement period– No Gel Cell

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 13: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 37 Battery Supervision

• Battery Supervision– How the panel supervises the battery.– Battery Trouble condition

• New battery consideration• 10.2 VDC panel disconnects battery

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 38 Power Requirements

• What happens during AC power failure

• All devices must be considered

• Battery calculator can be found on the website

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 39 Bell Output Terminals 5 & 6

• Bell Output Terminals• May output steady, pulsed or temporal• Note supervised bell output

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 14: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 40 Keypad Data Bus Terminals 7-10

– Four Terminals• Terminal 7 (RED)• Terminal 8 (YELLOW)• Terminal 9 (GREEN)• Terminal 10 (BLACK)

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 41 J8 Programming Header

• J8 Programming Header– 4 pin connection for keypad (330 harness)

• Quick and easy• Alternative to 7-10• Location

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 42 Smoke Power Terminals 11 & 12

• Smoke Power– 12VDC for 4 wire smokes

• Sensor reset – unlatches• Total current shared

– Total draw 1.5A• Ground reference

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 15: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 43 Protection Zones

• Protection Zones– Zone numbers 1 to 8

• Note on ground fault

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 44 Zone Operational Parameters

• Zone Operational Parameters– 3 zone conditions

• Open, Normal and Short

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 45 Powered Zones

• Powered Zones– Zones 9 and 10

• Class B (Style A)**• Note on separate negative terminals• Typical use• Note on programming

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 16: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 46 Grounded Zones vs. Class 'B' Zones

• Panel zones 1-8– Common ground

• Zones 9 and 10– Positive and negative

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 47 Dry Contact Outputs

• Dry Contacts Outputs– 2 Auxiliary relays– 305 Relays

• Rated for 1Amp at 30 VDC’

• 431 harness needed.

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 48 Open Collector Outputs

• Open Collector Outputs– Switch to ground (no voltage)

• Uses• 4 total numbered 3 to 6• Note on connecting devices

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 17: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 49 860 Relay Module

• 860 Relay Module– To provide relays for outputs 3 to 6

• Includes ONE relay• Power for unit• 3 hole pattern

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 50 J22 LX-Bus Header

• J22 LX bus header-Zones -Wireless -Programming

• J23 Jumper setting• Devices that can be used• Note on functionality

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 51 XR500 Only

• XR500 Interface cards• Interface card connection and Model 461

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 18: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 52 XR500 LX-Bus Numbering

• XR500 LX-Bus Numbering scheme• Example• Note on J22 and interface cards

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 53 XR100 LX-Bus Numbering

• XR100 LX-Bus Numbering– 100 zones available from J22– Zone Range

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 54 J21 RS232 Connector (XR500 ONLY)

• J21 RS-232 connector– Allows direct programming– Allows serial connections

• J23 in “R” position• Note on J21 and J22

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 19: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 55 RS-232 Status LEDs (XR500)

• RS-232 Status LEDs– Transmit LED operation– Receive LED operation

• Note on J23 and LX-Bus activity

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 56 LX-Bus LEDs (XR100)

• LX-Bus LEDs– Top LED operation– Bottom LED operation

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 57 J1- Ethernet Connector(XR500N shown XR100N similar)

• J1 Ethernet Connector– XR500N and XR100N -10base-T half duplex speed

• Link LED• Activity LED

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 20: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 58 J3-Telephone Connector

• J3 Telephone Connector– Connection to public telephone

• Proper Line Seizure is vital• Note on built in line monitor

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 59 Proper Line Seizure Wiring

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 60 J16- Panel Reset Jumper

• J16 Panel Reset Jumper– Location– Processor restart

• Process of resetting the panel• Note on jumper location when shipped

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 21: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 61 J4-Tamper Header

• J4 Tamper Header– For Options harness

• Detects unauthorized panel access

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 62 Wiring the Panel Review

The next 10 slides are a review for the Wiring the Panel Section

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 63 Question 1

1) When the battery voltage measured is below 11.9 VDC, a _______________ is indicated.

A. Battery TroubleB. Battery AlarmC. Battery Restoral

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 22: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 64 Question 1

1) When the battery voltage measured is below 11.9 VDC, a _______________ is indicated.

A. Battery TroubleB. Battery AlarmC. Battery Restoral

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 65 Question 2

2) The panel's Yellow wire is the _______________ wire.

A. transmitB. groundC. receiveD. smoke power

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 66 Question 2

2) The panel's Yellow wire is the _______________ wire.

A. transmitB. groundC. receiveD. smoke power

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 23: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 67 Question 3

3) The panel's Green wire is the _______________________ wire.

A. transmitB. groundC. receiveD. smoke power

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 68 Question 3

3) The panel's Green wire is the _______________________ wire.

A. transmitB. groundC. receiveD. smoke power

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 69 Question 4

4) The total combined current draw of all auxiliary devices powered by the panel must not exceed _______.

A. 50 mAB. 500 mA C. 1 AmpD. 1.5 Amps

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 24: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 70 Question 4

4) The total combined current draw of all auxiliary devices powered by the panel must not exceed _______.

A. 50 mAB. 500 mA C. 1 AmpD. 1.5 Amps

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 71 Question 5

5) Zones 1 through 8 cannot detect _______________ conditions.

A. openB. shortedC. ground fault D. trouble

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 72 Question 5

5) Zones 1 through 8 cannot detect _______________ conditions.

A. openB. shortedC. ground fault D. trouble

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 25: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 73 Question 6

6) The XR500 PCB provides ____ relay outputs, which are rated for 1 Amp at

30 VDC.

A. threeB. twoC. sixD. four

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 74 Question 6

6) The XR500 PCB provides ____ relay outputs, which are rated for 1 Amp at

30 VDC.

A. threeB. twoC. sixD. four

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 75 Question 7

7) To use the J22 LX-Bus header, set the 3-position jumper (J23) to the ____

position.

A. XB. RC. LD. none of these

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 26: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 76 Question 7

7) To use the J22 LX-Bus header, set the 3-position jumper (J23) to the ____

position.

A. XB. RC. LD. none of these

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 77 Question 8

8) XR500 Zone numbers begin at _______ on LX-Bus™ number four.

A. 300B. 400C. 401D. 800

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 78 Question 8

8) XR500 Zone numbers begin at _______ on LX-Bus™ number four.

A. 300B. 400C. 401D. 800

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 27: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 79 Question 9

9) When the three position jumper (J23) is set to “R” ________________________.

A. all of theseB. the panel may be connected to a serial deviceC. on-board LX-Bus is disabledD. an Interface card must be used for LX-Bus

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 80 Question 9

9) When the three position jumper (J23) is set to “R” ________________________.

A. all of theseB. the panel may be connected to a serial deviceC. on-board LX-Bus is disabledD. an Interface card must be used for LX-Bus

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 81 Question 10

10)The J1 Ethernet Connector has two LEDs. The Activity LED indicates

________________.

A. panel activityB. network activityC. door access activityD. computer activity

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 28: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 82 Question 10

10)The J1 Ethernet Connector has two LEDs. The Activity LED indicates

________________.

A. panel activityB. network activityC. door access activityD. computer activity

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 83 Addressing Keypads

• All keypads must have a unique address if supervised• If unsupervised, keypads can have same address• The addressing procedure differs between keypad

models

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 84 7000/690/790 SeriesKeypad Addressing

• 7000/690/790 Series Keypad Addressing– There are 6 steps in addressing a DMP keypad

through INSTaller Options

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 29: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 85 Rotary Switches

• Rotary Switches– 714 and 715 Zone expanders – Range for keypad bus addresses– Range for LX-Bus addresses

• Note on KP/LX-Bus jumper setting

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 86 Answering Machine Bypass

• Answering Machine Bypass– Operation

• Note on Armed Rings and/or Disarmed Rings

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 87 Finishing Up Review

The next 4 slides are a review for the Finishing Up Section

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 30: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 88 Question 1

1) The 7000/690/790 series LCD keypads are addressed through the ________________.

A. keypad busB. Installer OptionsC. dip switchesD. all of these

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 89 Question 1

1) The 7000/690/790 series LCD keypads are addressed through the ________________.

A. keypad busB. Installer OptionsC. dip switchesD. all of these

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 90 Question 2

2) When addressing a 7000/690/790 series keypad, you enter ________ (INST) at the SET BRIGHTNESS prompt to access the installer options.

A. 6653 CommandB. 8144 CommandC. 3577 CommandD. 99 Command

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 31: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

Slide 91 Question 2

2) When addressing a 7000/690/790 series keypad, you enter ________ (INST) at the SET BRIGHTNESS prompt to access the installer options.

A. 6653 CommandB. 8144 CommandC. 3577 CommandD. 99 Command

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 92 Question 3

3) To configure a device address for address 3, set the TENS switch to ____ and the ONES switch to address _____.

A. one, tenB. 3,1C. 3,0D. 0,3

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 93 Question 3

3) To configure a device address for address 3, set the TENS switch to ____ and the ONES switch to address _____.

A. one, tenB. 3,1C. 3,0D. 0,3

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Page 32: XT500/XR100 HARWARE AND INSTALLATION Slide 1 · 2009. 1. 19. · XT500/XR100 HARWARE AND INSTALLATION Slide 19 Question 1 1) The purpose of a site evaluation is to establish _____.

XT500/XR100 HARWARE AND INSTALLATION

8/08

Slide 94 Question 4

4) To achieve line seizure, the panel's phone jack (RJ31X or RJ38X) must be installed ______ the premise phones and the telephone company network.

A. betweenB. in parallel withC. after

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 95 Question 4

4) To achieve line seizure, the panel's phone jack (RJ31X or RJ38X) must be installed ______ the premise phones and the telephone company network.

A. betweenB. in parallel withC. after

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

Slide 96 Congratulations!

You have completed the XR500/XR100 Hardware & Installation course.

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

___________________________________

LT-1009 © 2008 Digital Monitoring Products, Inc.