WRXLink (04) - Subaru WRX & STI V10 04-06 and WRXLink (07) - Subaru WRX …linkecu.com/documentation/WRX10X.pdf · 1.2.3.1 Subaru Impreza WRX V1-10 ECU The G4X Subaru V1-10 Plug-In

WRXLink (04) - Subaru WRX & STIV10 04-06 and WRXLink (07) -Subaru WRX & STI V10 06-07

LINK ENGINE MANAGEMENT LTD – LIMITED LIFETIME WARRANTY

All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management Ltd aresubject to the following LIMITED LIFETIME WARRANTIES, and no others.

Link Engine Management Ltd warrants only to the original purchaser of the ECU, for the lifetime ofthe ECU, (subject to the limitations set out below), that the ECU shall be free from defects ofmaterials and workmanship in the manufacturing process. This warranty ceases to apply and doesnot apply to ECUs that have not been manufactured or distributed by Link Engine Management Ltdfor a period of greater than one year.

An ECU claimed to be defective must be returned to the place of purchase. Link Engine ManagementLtd, at its sole option, may replace the defective ECU with a comparable new ECU or repair thedefective ECU.

This limited lifetime warranty is not transferable and does not apply to any ECU not properly installedor properly used by the purchaser or end user, or to any ECU damaged or impaired by externalforces. The above warranties are the full extent of the warranties available on the ECU. Link EngineManagement Ltd has no liability to the original purchaser or any other person for any loss, injury ordamage to persons or property resulting from the use of the ECU or any failure of or defect in theECU whether by general, special, direct, indirect, incidental, consequential, exemplary, punitive, orany other damages of any kind or nature whatsoever. Link Engine Management Ltd specificallydisclaims and disavows all other warranties, express or implied, including, without limitation, allwarranties of fitness for a particular purpose, warranties of description, warranties of merchantability,trade usage or warranties of trade usage.

For off-road use only, not intended for highway vehicles. This ECU contains a user-configurablesoftware programme, which is updated by Link Engine Management Ltd from time to time. The usermust ensure the current correct version of this programme is downloaded from the website of LinkEngine Management Ltd and installed in the ECU prior to use. This limited lifetime warranty does notapply where the ECU has been installed with the incorrect version of the software programme. Theuser is solely responsible for the setup and testing of all user-configurable features.

Link Engine Management Ltd License Agreement

The software programme in this ECU is licensed not sold. Link Engine Management Ltd grants theuser a license for the programme only in the country where the programme was acquired. No otherrights are granted under this license and the programme may only be used on one machine at atime. If the programme is transferred a copy of this license and all other documentation must betransferred at the same time. The license may be terminated by the user at any time. Link EngineManagement Ltd may terminate the licence if the user fails to comply with the terms and conditionsof this license. In either event the copy of the programme must be destroyed.

Product Warranty Statement

5Contents

© 2020 Link Engine Management Ltd

Table of ContentsPart I G4X Plug-In ECU Installation Manual 6

................................................................................................................................... 61 Introduction

.......................................................................................................................................................... 6Safety Notice

.......................................................................................................................................................... 6Disclaim er

.......................................................................................................................................................... 6Suppor t Options

................................................................................................................................... 62 Pre-Instal lation

.......................................................................................................................................................... 7Com patibility Check

......................................................................................................................................................... 7WRXLink (10)

.......................................................................................................................................................... 7Board Sw itch Sett ings

......................................................................................................................................................... 7WRXLink (10)

.......................................................................................................................................................... 7Injector Im pedance

......................................................................................................................................................... 7Subaru Impreza WRX V1-10 ECU

................................................................................................................................... 83 Instal lation

.......................................................................................................................................................... 8ECU Handling Procedures

.......................................................................................................................................................... 8Fitt ing the ECU

......................................................................................................................................................... 8WRXLink (04) and WRXLink (07)

................................................................................................................................... 94 Additional Sensors/Functions

.......................................................................................................................................................... 9MAP Sensor

......................................................................................................................................................... 9WRXLink (04) & WRXLink (07)

.......................................................................................................................................................... 10IAT Sensor


.......................................................................................................................................................... 10E-Thrott le Output


.......................................................................................................................................................... 10Expans ion Connector

................................................................................................................................... 115 PC Tuning

.......................................................................................................................................................... 11Ins talling USB Dr ivers

.......................................................................................................................................................... 11Ins talling PCLink Tuning Softw are

.......................................................................................................................................................... 11Com m unicating With Your ECU

................................................................................................................................... 126 Pre-Start Configuration

.......................................................................................................................................................... 12Firm w are Vers ion

.......................................................................................................................................................... 12Base Configuration

.......................................................................................................................................................... 12MAP Sensor Calibration

.......................................................................................................................................................... 12TPS Calibration

.......................................................................................................................................................... 13IAT Sensor Selection

.......................................................................................................................................................... 13Input and Output Setup

.......................................................................................................................................................... 13Tr igger Calibration

................................................................................................................................... 147 First Time Startup

.......................................................................................................................................................... 14Final Checks

.......................................................................................................................................................... 14Init ial Setup

.......................................................................................................................................................... 17Essential Tuning Adjus tm ents

................................................................................................................................... 178 Pinouts

.......................................................................................................................................................... 17WRXLink (04) and WRXLink (07)

................................................................................................................................... 219 CAN Information


................................................................................................................................... 2210 Known Issues


Link ECU Online Manual6


1 G4X Plug-In ECU Installation Manual

1.1 Introduction

Thank you for purchasing your Link Plug-In Engine Control Unit (ECU), an advanced, fully programmablemicroprocessor controlled Engine Management System.G4X software employs high resolution fuel and ignition tables with configurable load and RPM centres. Whencoupled with up to six dimensional fuel and ignition mapping, barometric pressure compensation and intakeair temperature correction this gives an unprecedented level of tuning accuracy. All Link G4X ECUs are in-fieldupgradeable, there is no need to return the unit for software updates.All Link G4X Plug-In Engine Management Systems are designed with flexibility and ease of installation inmind. Link Plug-In systems are designed to replace the circuit board inside the factory ECU enclosure. Thisprovides an invisible install that requires minimal modification to vehicle wiring and ECU mounting.Installing and tuning any after market engine management system is not to be taken lightly. G4X ECUs givethe tuner the control & flexibility that only top after-market engine management systems in the world canprovide. While every effort has been made to keep G4X ECUs as user friendly as possible, it should berecognised that added features bring added complexity.The complete setup of your ECU can be divided into two important tasks:1. This manual covers the installation of your G4X ECU. While it is not strictly essential that this work is

performed by an automotive electrician, the knowledge and tools available to these professionals makes ithighly recommended. Regardless of who does the installation, it is of utmost importance that instructionsprovided in this manual are followed exactly throughout the installation.

2. Once the G4X ECU has been installed it will need to be tuned using a laptop computer with PCLinksoftware. Information on the configuration and tuning of the G4X ECU is detailed in the help section ofPCLink. G4X ECUs are shipped pre-loaded with a base configuration that should be close enough to getmost engines running after a few application specific adjustments have been made. While hearing theengine running on the new ECU for the first time is always a satisfying feeling, it is important to realisethat the job is not complete. The amount of tuning performed and the experience of the tuner are the twomost important factors in determining how happy you will be with your engine management system.

1.1.1 Safety Notice

Your Link Plug-In ECU is designed to enhance the performance of your vehicle. However in all cases, yourvehicle must be operated in a safe manner. Do not tune your vehicle while operating it on public roads.

WARNING!Failure to follow all installation and operating instructions may result in damage to

the Link ECU, personal injury, or harm to property.

1.1.2 Disclaimer

All care has been taken to ensure the pin outs and interconnections of the ECU to the vehicles wiring harnessare correct. However due to variations between vehicle models it is the installers responsibility to check wiringconnections BEFORE installing the ECU. Link will not be held responsible for any damage caused by theincorrect installation of this product.

1.1.3 Support Options

Should any issues arise during installation, the following options exist for technical support:1. PCLink help, press F1 while running PCLink2. Contact your nearest Link dealer. A Link dealer list is available on our website.3. Link website: www.linkecu.com with Online Discussion Forum.4. Technical Support Email: [email protected] majority of questions received by the technical support team are clearly answered in the manuals. Pleaseconsult the manuals to make sure that your question has not already been answered.

1.2 Pre-Installation

Before installing the Link G4X ECU into the vehicle some pre-installation checks must be performed.

G4X Plug-In ECU Instal lation Manual 7


1.2.1 Compatibility Check

It is essential that a compatibility check is performed before installing the ECU into the vehicle. Failure to doso may void the warranty. There are some cases where the same ECU connector is used on very similarvehicle models but with a completely different pinout.

1.2.1.1 WRXLink (10)

There are two different Subaru Impreza WRX V10 ECUs available. These are categorised as 2004-20062500cc and 2007 2500cc. This maybe slightly misleading as some 2006 vehicles require a 2007 ECU.It is critical that the correct ECU for the vehicle is installed, failure to install the correct ECU canresult in engine component, engine wiring or ECU damage.The correct ECU can be verified by studying the wiring loom.If pins A1, A2 and A3 (see pinout section) contain no wires, then the correct ECU required is the 20072500cc version. If these pins contain wires, then the correct ECU is the 2004-2006 2500cc version.

1.2.2 Board Switch Settings

Some Link G4X ECUs require switches on the board to be set before installation.

1.2.2.1 WRXLink (10)

There are jumpers located on the circuit board inside the case. These jumpers configure changes Subarumade between years. The jumpers MUST be set before installing the adapter in the vehicle.

When the jumper consists of three pins in a row,correct selection is made by moving the jumper tothe appropriate end of the three pins.

When the jumper consists of four pins in asquare, correct selection is made by positioningthe two jumpers in either vertical or horizontalorientation.

Information regarding the correct jumper position for the vehicle is printed on the PCB. To access the jumpers, one end plate must be removed from the case and the PCB will slide out. Ensure theadapter is fully unplugged before removing the end plate.

1.2.3 Injector Impedance

Injector impedance is important and needs consideration before installing the ECU.

1.2.3.1 Subaru Impreza WRX V1-10 ECU

The G4X Subaru V1-10 Plug-In ECUs are NOT designed to be used directly with low impedance injectors.All models this ECU is designed for are fitted with high impedance injectors from factory. This ECU has beendesigned to be used with HIGH impedance (greater than 6 Ohms) injectors. Ballast resistors must be wired iflow impedance injectors are to be used. This means that the ECU is plug-in compatible with factory fittedinjector combinations on all models, however if fitting low impedance injectors then ballast resistors must bewired. Contact your nearest Link dealer to purchase a ballast resistor pack if required.



1.3 Installation

This guide provides information on correctly and safely installing your new Link G4X Plug-In ECU.

1.3.1 ECU Handling Procedures

WARNING!!!The following installation process will require handling of both the Link ECU and

factory ECU. Both of these are highly sensitive to electrostatic discharge and areeasily damaged. Follow the anti-static precautions given in this manual carefully

to avoid damaging electronic components. Warranty claims for ECUs damaged byelectrostatic discharge will NOT be accepted.

ANTI-STATIC HANDLING GUIDELINES

Your body builds up an electrical charge as you move around. This charge can reach very highvoltages. Whenever given the opportunity this energy will attempt to discharge (usually through

your finger tips!). This can be fatal to most electronic components. Most people haveexperienced an electrostatic discharge when they step out of their car or touch a metal bench

top. 1. The following guidelines describe precautions that can be taken to reduce the possibility of

damaging your ECU:2. Work only on a conductive surface. A clean steel bench is suitable.

3. Always wear a wrist strap that is electrically connected to the conductive working surface.4. Touch the working surface regularly.

5. Do NOT touch components on the circuit board.6. Where possible, only handle the ECU by its plastic header.

7. Do NOT carry the ECU around without anti-static packaging. 8. Do NOT touch the bare terminals in the ECU header.

Observing the above procedures will minimise the chance of damaging the ECU. Note thatfailure due to static damage often does not appear until well after it was caused.

1.3.2 Fitting the ECU

Information is provided to assist in fitting the ECU into the vehicle.

1.3.2.1 WRXLink (04) and WRXLink (07)

The following steps outline the installation procedure for Subaru Plug-In ECUs:1. Remove the factory ECU from the vehicle: Ensure the key is in the OFF position. The factory ECU is

located under a steel cover on the passengers side floor (below the passengers feet). Lift the carpet,remove the cover panel. Unplug the wiring harness from the factory ECU. Remove the 6mm bolts (10mmsocket) that retain the ECU and remove the ECU from the vehicle. DO NOT touch the exposed pins in thefactory ECU connector.

2. Remove the factory ECUs circuit board from its enclosure: Ensure you are following the given anti-staticguidelines and ARE WEARING A CONDUCTIVE WRIST STRAP connected to a conductive workingsurface. Remove the top and cover from the ECU enclosure by removing the side retaining screws.Remove the circuit board by removing the retaining screws. Hold it only by the plastic header and place itaside.

3. Fit the Link Plug-In ECU: Remove the ECU from its packaging and place it immediately in the factoryenclosure. Place the factory ECU in the packaging your Link ECU came in for its protection.



Note: The G4X WRXLink (04) Plug-in ECU can fit two case sizes. If the ECU PCB is too large for the case,carefully snap the PCB extensions off at the lines shown in the image below.

4. If the ECUs USB tuning cable is to be left permanently connected, a slot will need to be cut in the topcover. The best place to do this is usually beside the factory header.

5. Reassemble the enclosure and fit the ECU back to the vehicle.6. Connect the ECU to the factory wiring loom. 7. Do NOT attempt to start the vehicle. Proceed to read through the remaining sections of this manual first.

1.4 Additional Sensors/Functions

G4X Plug-In ECUs offer various options for the installation of additional sensors and devices. As a minimum itis recommended that all ECUs are installed with a Manifold Absolute Pressure (MAP) sensor and Intake AirTemperature (IAT) sensor. These parts can be purchased if required from your nearest Link dealer.

1.4.1 MAP Sensor

It is important that the pressure source for a MAP sensor be taken from a stable pressure source after thethrottle body. It is common to 'T' into the fuel pressure regulators pressure signal. Do NOT share this signalwith other devices such as boost gauges or blow off valves.

1.4.1.1 WRXLink (04) & WRXLink (07)

The Link G4X WRXLink (04) & WRXLink (07) plugins support several options for fitting of a MAP sensor, anyone of the following options can be used:1. Factory MAP Sensor – From factory, all models supported by this ECU are fitted with a factory MAP

sensor. The factory MAP sensor is wired to An Volt 1. The factory sensor is good for 160kPa (23psi) ofboost.

2. Factory MAP Sensor Upgrade – The factory MAP sensor can be upgraded by simply replacing the factoryMAP sensor. Contact your nearest Link dealer for upgrade options.

Make sure that the correct MAP sensor input has been selected in PCLink and a MAP calibration has beenperformed before attempting to start the vehicle.



1.4.2 IAT Sensor

It is highly recommended that an IAT sensor be fitted in all applications to provide an input for correction offuel and ignition based on the engines air charge temperature.An IAT sensor should be fitted in the intake system in a location that accurately represents intaketemperature. The most common location is just prior to the throttle body. Installing in the manifold is notrecommended due to heat soak issues. A fast response sensor must be used in all forced inductionapplications.


The AFM has a factory fitted IAT sensor. Due to its location this sensor is not suitable for tuning. A suitableIAT sensor can however be wired to the AFM wiring. The AFMs IAT signal is wired to An Temp 2. FactoryAFM wiring information follows:

1 +14V2 Ground3 Mass Air Flow Meter4 Intake Air Temperature5 Ground

Note: It is important that the factory IAT sensor is completely disconnected as not to affect the after marketIAT sensor signal.

An IAT sensor can also be wired in using any spare An Temp or An Volt pin (several are available on theexpansion connectors). Note spare An Volt channels require a pullup resistor (to +5V) to be added fortemperature input use.

1.4.3 E-Throttle Output

It is becoming more common to convert cable throttle vehicles to Electronic Throttle control, this sectionexplains how (if it is possible) to do this for each plugin.


This vehicle has E-Throttle from factory and so does not require any modifications.The E-Throttle Output pins are Aux 9 & 10 and the EThrottle Relay is Aux Ignition 8. If the EThrottle is foundto be operating in the wrong direction this can be rectified by changing the Aux 9 Active State (ElectronicThrottle -> E-Throttle 1 -> E-Throttle Setup or by swapping the +ve and -ve pins at the throttle plug.

1.4.4 Expansion Connector

Expansion connectors are provided to allow easy connection of additional ECU inputs. An “expansion cable”can be purchased from your Link dealer. Important points when wiring to the expansion connector:· Do not overload the +5V Out pin. Although this is protected against ECU damage the +5V out signal also

provides power for other sensors.· Do not connect the ground pin to chassis ground. This could cause ground loops and introduce

unnecessary interference. Use this pin only to ground external sensors that are isolated from chassisground.

The Expansion connectors available for each ECU can be found under the Pinouts Section.



1.5 PC Tuning

G4X ECUs require PC/laptop tuning using the PCLink Tuning Software application running on a Windowsbased computer. PCLink may be downloaded from www.linkecu.com. Note that when new versions of PCLinkare released they are posted on the website and may be downloaded at no cost. Also note that G4X ECUsmust be used with the correct version of PCLink.

IMPORTANT!The G4X ECU has on board USB.

BEFORE connecting the ECU to your laptop, the USB drivers must be installed.Failure to install the drivers on your laptop first may result in windows assigningincorrect drivers. These drivers will not work with the G4X ECU and are difficult touninstall. The correct USB drivers are installed as part of PCLink installation, asdescribed in the following section. Should internet download not be practical, a

copy of the drivers on CD can be obtained from your nearest Link dealer.

1.5.1 Installing USB Drivers

Before connecting the ECU to your laptop or PC, the ECU USB drivers must be installed. These drivers areinstalled as part of PCLink installation as described in the following section. Should internet download not bepractical, a copy of the drivers on CD can be obtained from your nearest Link Dealer.

1.5.2 Installing PCLink Tuning Software

Due to the frequent updates PCLink is no longer shipped with each ECU. You will be required to download thelatest version of PCLink from: linkecu.comShould access to an Internet connection be impractical, download the latest version of PCLink elsewhere to aUSB drive, and then install on your laptop.Installing from the web1. Go to the above website and navigate to the downloads and software updates section.2. Download the latest version of PCLink. When prompted to run or save the file, select save. It is

recommended to save this file on the desktop.3. Double click the saved file and follow on screen instructions.4. When prompted to install USB drivers, select yes. This may take some time.5. When installed, open PCLink by double clicking on the icon that has been placed on the desktop.

1.5.3 Communicating With Your ECU

After PCLink installation, you will be able to connect the G4X ECU to the laptop to perform set-up and tuningwork.1. Connect the ECU to your laptop using a Link G4X ECU USB Cable. If not supplied with the ECU, these

can be purchased from a Link dealer. No other adapter or cabling is required. Connect the cable to theconnector labelled USB.

2. If this is the first time you have connected a G4X USB ECU to your laptop follow the driver installationinstructions that appear. When prompted if you want to install drivers select 'Continue Anyway'.

3. Start PCLink by double clicking on the PCLink icon on the windows desktop.4. Switch the key to the ON position. This will provide power to the ECU.5. In PCLink, under the 'Options' menu, select 'Connection'. The connection options dialogue will open.

Select the correct COM Port number from the drop down list or select auto for automatic com portdetection.

6. PCLink offers both mouse and keyboard control. To establish a connection between the PC and ECUpress the F3 key. The same process can be used to disconnect. If a successful connection isestablished, PCLink will download settings from the ECU, otherwise you will be warned that an error hasoccurred.

7. Make sure the connection shows “ONLINE” in the top right corner of PCLink.8. To permanently STORE any changes made to the ECU press F4. If this is not done before turning the

ECUs power off all changes made will be lost.



1.6 Pre-Start Configuration

Before starting the vehicle, important pre-start configurations need to be made.

1.6.1 Firmware Version

It is recommended to ensure that the Link G4X ECU is running the most up to date firmware. Firmwareversion information can be obtained by connecting to the ECU with PCLink and selecting 'ECU Information'under the Help menu.The latest firmware can be downloaded from our website with PCLink. It is recommended that this is performed by an experienced Link dealer as new features may need to beproperly configured.The firmware can be updated by selecting 'Update Firmware' under the 'ECU Controls' menu in PCLink, followthe on screen instructions to complete the firmware update process.

1.6.2 Base Configuration

All G4X Plug-In ECUs are shipped with base configuration settings. Note that these are provided to reduceinitial setup and tuning times. They are NOT recommended tuning values. PCLink includes baseconfigurations for various models. Download the appropriate base configuration into your ECU with PCLink byconnecting to the ECU (described in the Connecting To PCLink section of this manual), then selecting 'Open'under the 'File' menu. Select the appropriate .pclx file and then select 'Open'. Downloading large configurationfiles can take up to a few minutes. Be patient and acknowledge any messages PCLink shows.

1.6.3 MAP Sensor Calibration

At key on and engine not running the Manifold Absolute Pressure (MAP) Sensor should always match theBarometric Absolute Pressure (BAP) Sensor. As well as providing altitude correction, the BAP sensor alsoallows the MAP sensor to be calibrated prior to tuning.Link G4X ECUs use an on-board barometric sensor that is calibrated prior to dispatch. This ensures that allPCLink Tuning Software programs (pclx Files) give a consistent state of tune throughout the ECU range. Thisallows a pclx file to be transferred between G4X based ECUs giving an equivalent state of tune providing allfactors affecting volumetric efficiency are equal.Without the ability to calibrate all the available types of MAP Sensors to the BAP Sensor there would besignificant affects on the accuracy of the resulting tune, especially when tuning with Manifold Gauge Pressure(MGP) as a load index.To calibrate the MAP sensor:1. Connect a laptop/notebook PC to the ECU and connect to the ECU using PCLink.2. Under the Analog Channels menu, select the An Volt channel that has been wired to the MAP sensor.

Select the correct MAP Sensor Type.3. Under the 'Options' menu, select 'MAP sensor calibration'.4. Follow the on screen instructions.5. Select the 'Analog Inputs' tab in the runtime values section of PCLink (lower part of the screen).6. Compare the MAP and BAP values and ensure they have a similar reading (within 1 kPa).7. Perform a 'Store' by pressing F4.

A more in depth explanation is provided in the PCLink help Manual under PCLink G4X Users Manual ->Tuning Operating Procedures -> ECU Controls -> MAP Sensor Calibration.

1.6.4 TPS Calibration

The Throttle Position Sensor (TPS) is used by the ECU to calculate various engine management parametersused by functions such as idle speed control,acceleration enrichment and motor sport features. It is importantthat the ECU knows when the throttle is open and closed (or part way in between). The following procedurecalibrates the ECU to match the TPS and is for engines using a cable driven throttle:1. Connect a laptop/notebook PC to the ECU and connect to the ECU using PCLink.2. Under the Analog Channels menu, ensure that the correct An Volt channel is set to 'TPS (Main)'. Refer to

the pin functions section of this manual for details.3. Under the 'Options' menu, select 'TPS calibration'.4. Follow the on screen instructions.5. Select the 'Analog Inputs' tab in the runtime values section of PCLink (lower part of the screen).



6. Ensure the Throttle Position value reads 0% when the throttle is closed and 100% when fully open.7. Perform a 'Store' by pressing F4.

For engine setups that use Electronic Throttle Control the Accelerator Position Sensor (APS) and ThrottlePosition Sensor (TPS) need to be calibrated.

For Link Plug-in ECUs see PCLink Help > G4X ECU Tuning Functions > Electronic Throttle Control

1.6.5 IAT Sensor Selection

This section only applies when an Intake Air Temperature (IAT) sensor has been wired and fitted to the intakesystem. It is important that the ECU is calibrated to match the sensor installed in the engine. This procedureis as simple as selecting the correct sensor type as follows:1. Connect a laptop/notebook PC to the ECU and connect to the ECU using PCLink.2. Click on 'Analog Channel' in the configuration tree.3. Select the An Temp channel the sensor has been wired to.4. Ensure that channel (and only that channel) is set to 'Inlet Air Temperature'.5. Select the correct 'Temp Sensor Type'.6. Select the 'Analog Inputs' tab in the runtime values section of PCLink (lower part of the screen).7. Ensure that IAT reads the correct temperature.8. Perform a 'Store' by pressing F4.

1.6.6 Input and Output Setup

As the Link G4X Plug-In ECUs are designed to run several models there are a few items that must be set-upto make the ECU specific to your model. The Pin Functions section of this manual gives a list of the functions of each channel based on the targetvehicle.It is the tuners responsibility to make sure that the following channels are set-up correctly for the vehiclemodel the ECU is fitted to:All Auxiliary Output Channels Use the 'Test On' or 'Test PWM' (at 10 Hz) functions to test the wiring of channels.All Digital InputsLook at the Digital Inputs runtime values (lower section of the PCLink screen) to confirm each channelsoperation.All Analog Volt and Temperature InputsLook at the Analog Inputs runtime values (lower section of the PCLink screen) to confirm each channelsoperation.

1.6.7 Trigger Calibration

The following instructions assume that all pre-start set-up instructions given in previous sections have beencompleted. Only after all pre-start checks have been made should an attempt be made to crank the engine.The following steps must be performed before an attempt is made to start the engine to ensure the G4X ECUis calibrated to precisely measure engine position.1. Connect the ECU to PCLink.2. Select 'Fuel', then 'Fuel Set-up':

a. Set ‘Injection Mode’ to OFF. This will prevent the engine from trying to start while the triggers arecalibrated.

b. Perform a Store (press F4) to make sure fuelling is not re-enabled if power to the ECU is lost.3. Click on ‘Triggers’ then ‘Calibrate Triggers’.4. Perform the correct trigger calibration procedure specific to your vehicle as described in the PCLink help

(Press F1).Note that trigger calibration must be performed again once the engine is running. Due to the acceleration anddeceleration of the crankshaft at low speeds, an inaccurate measurement of engine timing is usually made.Also it is often harder to see timing marks with a timing light at slow engine speeds. Trigger calibration shouldbe checked again at between 2000-4000 RPM where engine speed is stable and a more consistent timingreading can be obtained.



A more in depth explanation is provided in the PCLink help Manual under G4X ECU Tuning Functions ->Triggers -> Calibration.

1.7 First Time Startup

After performing all set-up instructions given in previous sections, including trigger calibration, the engine isnow ready to be started. The following procedure should be used for first time start-up.1. Turn the ignition key OFF then ON. The fuel pump should prime momentarily upon power up.2. Connect the ECU to PCLink.3. Access the runtimes values by pressing the F12 Key, click the 'Analog' tab:

a. TPS – spans from 0 to 100% when throttle is pressed. If not, perform a TPS Calibration.b. MAP – should read approx 101 kPa (at sea level) with the engine not running. If not, check the MAP

Sensor Type setting and perform a MAP Calibration.c. ECT – should read current engine temperature.d. IAT – should read current intake air temperature.e. Digital Inputs (click the 'Digital' tab) – Operate switches connected to any digital inputs while watching

the runtime value to ensure they operate as expected.4. Rectify any faults found in Step 3.5. Locate the 'Master Fuel' setting. This can be found in the ECU Settings Menu under: Fuel > Fuel Setup >

Fuel Main.a. This will need to be adjusted during or just after start-up.

6. Crank the engine until it starts. Some throttle may be required for first time start-up due to imperfecttuning. If necessary adjust the Master setting to enrich/lean the engine (increase to enrich).

7. If the engine fails to start after several attempts, do not crank it endlessly. Stop and determine theproblem before continuing.

8. Check the Trigger Error Counter (found under the Triggers runtime values tab). If this value increasesduring cranking/running then there is a trigger setup fault. It is not unusual for this number to count one ortwo on the first engine revolution.

9. Once the engine starts, adjust the ‘Master’ (under fuel settings) setting to achieve best possible running.10. The engine should now be allowed to fully warm up. It may be necessary to readjust ‘Master’ several

times to maintain smooth running. Don’t forget to keep an eye on engine temperature.11. Once the engine is warmed up and running well, perform another trigger calibration (known “as setting the

base timing”).12. Perform a Store by pressing F4.

1.7.1 Final Checks

To avoid potential engine damage and wasted time, the adjustments presented in the following sections mustbe made before attempting to start the engine.For further help on any of the settings discussed below, consult the Help in PCLink Tuning Software. Helpcan be invoked by pressing F1, or right clicking any item and selecting ‘What’s this?’.

Pre-set-up ChecksBefore attempting to configure the ECU, ensure the following tasks have been completed:1. Ensure the ECU and all associated components are connected and correctly wired/installed.2. Fully charge the vehicle’s battery, as the engine will be required to be cranked during the set-up

procedure.3. Check all oil and water levels are correct.Connecting to PCLink Tuning SoftwareUse the following procedure to establish a connection between your Link ECU and PCLink Tuning Softwaretuning software.1. Make sure your laptop battery is fully charged or plugged in to mains power.2. Connect the ECU to your laptop and connect to PCLink as described in the 'Communicating with your

ECU' section of this manual.

1.7.2 Initial Setup

After all checks described in previous sections have been performed, the ECU is ready to be configured for aparticular application. The following set-up procedure should be used on all installations as a minimum:Configuration and Fueling Set-up



If the ECU is to be used to control fuel injection, all of the following steps must be performed. If the ECU willnot be controlling fuel injection, then only steps 1 and 2 are required.

1. If you have a .pclx file containing a base configuration, thisis the time to load it into the ECU. To do this, select ‘Open’form the ‘File’ menu. Select the required .pclx file and thenselect ‘Ok’. When prompted if you want to load the file intothe ECU, select ‘Yes’.

2. Click on the ‘Configuration’ heading in the ECU Settingsfunction tree (top left of PCLink Tuning Software screen):a. Select the correct engine typeb. Select the correct number of cylinders/rotors.c. Enter the engines firing order.

3. Click on Fuel > Fuel Setup > Fuel Main:a. Select the desired Injection Mode (e.g. Sequential or

Group).b. Select 'Fuel Table1' from under the 'Fuel' heading. Right

click on the table, select 'Axis Setup'. Set the Y Axis(Load) to the appropriate option (e.g. MGP or TPS).

4. Click on ‘Accel Enrichment’:a. Turn Accel Mode OFF for first time set-ups.

5. Click on Fuel Corrections > IAT Fuel Correction:a. If air temperature correction is to be used and an air

temperature sensor is fitted, set the ‘IAT Mode’ to ON.Then select and fill in the IAT Fuel Trim Table.

b. Turn OFF air temp correction (under ‘IAT Mode’) if airtemperature correction is not going to be used

6. Click on Fuel > Fuel Setup > Injector Setup:a. Select '2D Table' or '3D Table'. Fill in the dead-time table

with the information from your injector data-sheet.7. Click on ‘Overrun Fuel Cut’:

a. Set ‘Fuel cut Mode’ to OFF.8. Click on Fuel Corrections > Dual Fuel Table:

a. Set Table 2 Mode' to OFF.9. Click on Fuel Corrections > 4D Fuel Table:

a. Set ‘4D Fuel Mode’ to OFF.10. Click on Fuel Setup > Injector Test:

a. Turn each injection channel on one by one and checkthat the correct cylinders injector clicks. Fix anyproblems now if the injectors do not operate.

11. Perform a Store to permanently save changes to the ECUby pressing F4.

Ignition Set-upIf the ECU is to be used to control ignition, all of the following steps must be performed. If the ECU will not becontrolling ignition, then only the first step is required.

1. Click on Ignition > Ignition Set-up > Ignition Main:a. Select the correct type of ‘Ignition Mode’ for the

application. Set to 'OFF' if ignition is not controlled bythe ECU.

b. Set ‘Maximum Advance’ to a suitable value.c. Enter appropriate values for coil dwell time in the

‘Ignition Dwell Time’ table.2. Click on Ignition Corrections > ECT Ign Trim:

a. Set ECT Trim Mode to OFF (for now).3. Click on ‘IAT Ign Trim’:

a. Set IAT Trim Mode to OFF (for now).4. Click on Individual Cyl Ign Trim > Individual Cyl Ign Trim:

a. Set ‘Indiv Ign Mode’ to OFF (for now).5. Click on Ignition Corrections > Dual Ign Table:

a. Set Table 2 Mode to OFF (for now).



6. Click on ‘4D Ign Table':a. Set ‘4D Ign Mode’ to OFF (for now).

7. Click on Ignition Setup > Ignition Test:a. Turn each ignition channels test function on one by one.b. Check for a quiet clicking sound from each coil or

alternately connect a spark gap and check for spark onthe correct cylinders.

c. Correct any problems before continuing.8. Perform a Store to permanently save changes to the ECU

by pressing F4.Limits Set-upAt this stage it is not necessary to precisely set all limits. However, it is essential to ensure they are set tovalues that will not interfere with tuning procedures. It is advisable to err on the conservative side when settinglimit values.

1. Click on Limits > RPM Limit > RPM Limit:a. Select the desired ‘RPM Limit Mode’ b. Select the RPM Limit Table, enter the required RPM

limiting value for each engine temperature in the ‘RPMLimit Table’.

2. Click on Limits > MAP Limit > MAP Limit:a. Select the desired ‘MAP Limit Mode’ b. Select the MAP Limit Table, enter the required MAP

limiting value for each engine temperature in the ‘MAPLimit Table’.

3. Click on Limits > Speed Limit:a. Set 'Speed Limit Switch' and 'Speed Limit Switch 2' to

'OFF' to ensure it is not invoked during tuning. Note thatthis limit will only be effective if a vehicle speed sensoris correctly wired and configured.

4. Perform a Store to permanently save changes to the ECUby pressing F4.

Trigger Set-upTrigger set-up requires entering information regarding the way in which engine speed and position ismeasured. Consult the PCLink Tuning Software online help for further information on functions.

WARNING!These are probably the most critical set-up values. Do not attempt to startthe engine unless you are 100% confident that these values are correct.

If trigger information is unknown, consult your nearest Link dealer for further assistance.1. Click on ‘Triggers’ then ‘Trigger Set-up’:

a. Configure triggers as required.2. Click on ‘Trigger1’:

a. Select correct trigger type and set-up completely.3. Click on ‘Trigger2’:

a. Select correct trigger type and set-up completely.4. Perform a Store to permanently save changes to the ECU

by pressing F4.Additional Set-upIt is important that all features not required for initial tuning are either disabled or correctly set-up. It isrecommended that features be initially disabled to ensure they do not complicate tuning.

1. Click on ‘Motorsport’ then ‘Antilag’:a. Set ‘Antilag Mode’ to OFF.

2. Click on ‘Launch Control’:a. Set ‘Launch Control Mode’ to OFF..

3. Click on 'Gear Cut Control’:a. Set 'Gear Cut Control Mode’ to OFF.

4. Click on Boost Control > Boost Set-up:a. Configure Boost Control as described in the PCLink

Tuning Software online help.5. Click on 'Multiple Boost Tables':



a. Set 'Active Tables' to 1 Table.6. Perform a Store to permanently save changes to the ECU

by pressing F4.

1.7.3 Essential Tuning Adjustments

It is assumed that at this stage all set-up procedures described in previous sections have been completedand the engine is running.The following steps detail correct set-up procedures for some of the more criticalECU parameters (note that MAP Sensor Calibration should have already been completed by now):

Injector Voltage (Dead-time) CorrectionThere is always a delay between the injector being energised and the injector actually opening. Likewise,there is a small delay between the injector being de-energised and the injector closing. The opening time isconsiderably longer than the closing time, however the overall result is that less fuel will flow for a given pulsewidth than would be expected with an 'ideal injector'. To compensate for this the injector pulse widths areincreased to compensate for this 'dead-time'. The dead-time for a given injector is a function of the batteryvoltage, differential fuel pressure and the type of injector driver (saturated or peak and hold). A typical dead-time at 3 Bar differential fuel pressure and 14 volts is just under 1ms (ms = millisecond = 1 thousandth of asecond). In applications with a linear 1:1 fuel pressure regulator (i.e. not a rising rate regulator), the differential fuelpressure (difference between manifold pressure and fuel pressure) will be constant. Therefore the only variablethat is changing will be the battery voltage (this changes with electrical load and sometimes engine speed).Without correction, the changes in dead-time will cause the engine to run lean when the voltage drops. If theInjector Voltage Correction is properly set-up then changes in the battery voltage will not affect the air/fuelratio.The injector dead-time table allows the dead-time for different battery voltages to be entered. The valuesrepresent the dead-time in milliseconds. These should increase with falling system voltage.Injector dead-time for a particular set of injectors can be determined using a flow bench or on a runningengine. To determine the injector dead-time using a flow bench, the injectors need to be operated at the intendedoperating pressure (normally three bar) and at a constant duty cycle as well as a set voltage. Vary the supplyvoltage to the injector and measure minimum pulse width at which the injectors will flow for a particularvoltage. This is the required dead-time for that injector at that tested voltage. To determine injector dead-time on a running engine, with the engine fully warmed and operating at stableair/fuel ratios (a very precise AFR meter is required – a narrow band O2 sensor will not suffice), electricaldrain needs to be applied to the system; the preferred method is disconnecting the alternator main fuse.Battery load testers are also useful here too.Watching the air fuel ratios change while the battery voltage drops, the dead-time table can be trimmed tomaintain the same stable air/fuel ratio. Injector dead-time can be viewed as a row graph. A smooth curveneeds to be maintained at all times.NOTE: any change to the fuel pressure or injectors will require a recalibration of the injector dead-times.

MasterMaster should be set so that the numbers in the middle of the fuel table end up around a value of 50. This isto allow sufficient span of the numbers in the main fuel table.

1.8 Pinouts

Pin information is provided to assist when troubleshooting. All pinouts are looking into the ECU (wire side).

1.8.1 WRXLink (04) and WRXLink (07)

The following pin diagram is provided as a support reference. Please contact your nearest Link dealer forspecific pin information.



2004 - 2006 ECU Function

Pin ECU Pin Function Pin ECU Pin Function

A1 DI 4 Clutch Switch C3 Injector 4 Injection

A2 nc C4 Injector 3 Injection



A5 nc C7 DI10

A6 Ground C8 nc (Brake NO)

A7 nc C9 DI 5 Brake Switch (NC)

A8 Aux 8 Tumble Valves Close C10 DI 6 Cruise Cancel OR Resume

A9 Linked to A9TGV wired in series

C11 DI 7 Cruise Set OR Cancel

A10 Linked to A8 C12 An Temp 3 Fuel Temperature

A11 Aux 7 Tumble Valves Open C13 An Temp 2 IAT from MAF

A12 nc C14 An Temp 1 ECT

A13 nc C15 +5V Out

A14 Injector 5 (Aux) Purge Solenoid C16 +5V Out

A15 Injector 6 (Aux) Cruise Light C17 An Volt 10 APS (Main)

A16 nc (Cruise SetLight)

C18 An Volt 2 TPS (Main)

A17 Injector 8 (Aux) CE Light C19 nc

A18 +14V Out AVCS Solenoid C20 nc

A19 +14V Out AVCS Solenoid C21 nc

A20 nc C22 An Volt 1 MAP

A21 nc C23 An Volt 8 MAF Signal

A22 nc C24 nc

A23 Aux 3 Tacho C25 Knock 1 Knock

A24 nc C26 An Volt 4 Left TGV Position

A25 Ground C27 An Volt 5 Right TGV Position

A26 nc C28 An Volt 9 APS (Sub)

A27 nc C29 An Volt 3 TPS (Sub)

A28 Aux 2 Bank 1 (RH) AVCSSolenoid

C30 nc

A29 Aux 1 Bank 2 (LH) AVCSSolenoid

C31 Ground (AFM)

A30 nc C32 Ground (AFMShield)

A31 nc C33 Ground (KnockShield)

A32 Aux 5 Wastegate Solenoid C34 Ground (APS)

A33 nc C35 Ground (Signal)

A34 Ground (Signal)

D1 Ground (Signal)

B1 Ground D2 Ground (Signal)

B2 Injector 7 (Aux) Rear Oxy Heater D3 Ground

B3 nc D4 Aux 9 EThrottle Motor +

B4 Ground D5 Aux 10 EThrottle Motor -

B5 +14V Main Relay ECU Power D6 +14V EThrottle From EThrottle Relay

B6 +14V Main Relay ECU Power D7 Ground

B7 nc D8 DI 8 Start Signal



B8 Trig 2 Bank 2 (LH) CamPosition

D9 DI 9 Neutral Signal

B9 DI 2 Bank 1 (RH) CamPosition

D10 An Volt 6 Power Steer Switch

B10 Trig 1 Trig 1 (Crank) D11 nc

B11 nc D12 nc

B12 Ground D13 nc

B13 nc D14 Ignition Switch (05-06)

Controls Main Relay (05-06)

B14 nc D15 Ignition Switch (04) Controls Main Relay (04)

B15 Ignition 4 Ignition D16 DI3 (04) / MainRelay (05-06)

AC Request (04) / Groundwhen on (05-06)

B16 Ignition 3 Ignition D17 Main Relay (04) /DI3 (05-06)

Ground when on (04) / ACRequest (05-06)

B17 Ignition 2 Ignition D18 nc

B18 Ignition 1 Ignition D19 nc

B19 nc D20 nc

B20 nc D21 nc

B21 nc D22 nc

B22 Ground (Cams) D23 nc

B23 nc D24 nc

B24 Ignition 5 (Aux) AC Fan D25 An Volt 7 Rear Oxy Signal

B25 Ignition 7 (Aux) Engine Fan D26 nc

B26 Aux 6 (04) / DI 1(05-06)

FP Speed (04) / VehicleSpeed (05-06)

D27 nc

B27 DI 1 (04) / Aux 6(05-06)

Vehicle Speed (04) / FPSpeed (05-06)

D28 nc

B28 nc D29 nc

B29 nc D30 nc

B30 nc D31 Ground (Shield)

B31 Ground (CrankShield)

Expansion 1

Ground (Signal)

B32 nc Expansion 2

+5V Out

B33 Ignition 6 (Aux) AC Relay Expansion 3

nc

B34 nc Expansion 4

nc

B35 Ignition 8 (Aux) E-Throttle Relay Expansion 5

An Volt 12

Expansion 6

nc

C1 nc Expansion 7

An Temp 4

C2 nc Expansion 8

An Volt 11

2006-2007 ECU Function

Pin ECU Pin Function Pin ECU Pin Function

A1 nc C3 nc (Front O2Heater)

A2 nc C4 Injector 7 (Aux) Rear Oxy Heater



A3 nc C5 nc

A4 nc C6 Ground (Shield)

A5 Ground C7 nc

A6 An Volt 1 MAP (Factory) C8 nc

A7 +14V Main Relay ECU Power C9 Ignition 6 (Aux) AC Relay

A8 nc C10 nc

A9 nc C11 Injector 8 (Aux) CE Light

A10 nc C12 nc (06) / Aux 6 (07) FP Speed (07)

A11 DI 2 Bank 1 (RH) CamPosition

C13 DI 1 Vehicle Speed

A12 nc C14 nc

A13 Trig 1 Trig 1 (Crank) C15 Ground (Signal)

A14 Ground (Crank) C16 nc

A15 Knock 1 Knock C17 nc

A16 An Volt 4 Left TGV Position C18 Ignition 7 (Aux) Engine Fan

A17 nc C19 nc

A18 An Volt 2 TPS (Main) C20 nc

A19 +5V Out C21 Ignition 8 (Aux) E-Throttle Relay

A20 nc C22 Aux 3 Tacho

A21 Trig 2 Bank 2 (LH) CamPosition

C23 DI 3 (06) / MainRelay (07)

A/C Request (06) / Groundwhen on (07)

A22 Ground (Cams) C24 Main Relay (06) / DI3 (07)

Ground when on (06) / A/CRequest (07)

A23 nc C25 DI 4 Clutch Switch

A24 Ground (CrankShield)

C26 nc

A25 Ground (KnockShield)

C27 CAN 2 High

A26 An Volt 5 Right TGV Position C28 nc

A27 nc C29 Ignition 5 (Aux) AC Fan

A28 An Volt 3 TPS (Sub) C30 nc

A29 Ground (Signal) C31 DI 9 Neutral Signal

A30 nc C32 DI 8 Start Signal

A31 nc C33 nc

A32 nc C34 nc

A33 An Volt 6 Power Steer Switch C35 CAN 2 Low

A34 An Temp 1 ECT

D1 Ground

B1 Ground (O2 Shield) D2 Ground

B2 +14V Main Relay ECU Power D3 Ground

B3 nc (Cruise SetLight)

D4 Aux 9 EThrottle Motor +

B4 An Volt 7 Rear Oxy Signal D5 Aux 10 EThrottle Motor -

B5 nc (+12V constant) D6 nc

B6 Injector 6 (Aux) Cruise Light D7 Ground

B7 nc D8 Injector 1 Injection

B8 nc (Front O2 Signal-)

D9 Injector 2 Injection

B9 nc (Front O2 Signal+)




B10 nc (Fuel LevelSensor)


B11 nc D12 Linked to D23 TGV wired in series

B12 DI 10 Cruise Main D13 Aux 8 Tumble Valves Close

B13 DI 6 Cruise Cancel ORResume

D14 Aux 1 Bank 2 (LH) AVCS Solenoid

B14 nc D15 +14V Out AVCS Solenoid

B15 nc D16 Aux 2 Bank 1 (RH) AVCS Solenoid

B16 nc D17 +14V Out AVCS Solenoid

B17 An Temp 3 Fuel Temperature D18 Ignition 1 Ignition

B18 An Temp 2 IAT from MAF D19 Ignition 2 Ignition

B19 Ignition Switch Controls Main relay D20 Ignition 3 Ignition

B20 DI 5 Brake (NC) D21 Ignition 4 Ignition

B21 +5V Out (APSMain)

D22 Aux 7 Tumble Valves Open

B22 +5V Out (APSSub)

D23 Linked to D12 TGV wired in series

B23 An Volt 10 APS (Main) D24 nc

B24 DI 7 Cruise Set ORCancel

D25 nc

B25 nc D26 Ground

B26 An Volt 8 MAF Signal D27 Aux 5 Wastegate Solenoid

B27 nc D28 nc

B28 nc (brake NO) D29 Injector 5 (aux) Purge Solenoid

B29 Ground (APS Main) D30 nc

B30 Ground (Signal) D31 nc

B31 An Volt 9 APS (Sub) Expansion 1

Ground (Signal)

B32 nc (Fuel TankPressure)

Expansion 2

+5V Out

B33 Aux 6 (06) / nc (07) FP Speed (06) Expansion 3

DI 11

B34 Ground (AFM) Expansion 4

Aux13

B35 Ground (AFMShield)

Expansion 5

An Volt 11

Expansion 6

Aux 12

C1 +14V EThrottle From EThrottleRelay

Expansion 7

An Temp 4

C2 nc (Front O2Heater)

Expansion 8

Aux 11

1.9 CAN Information

The following CAN (Controller Area Network) information is provided:


The G4X WRXLink (04) and WRXLink (07) Plug-in ECU has two CAN buses. These CAN buses exist tosupport aftermarket CAN devices.

CAN bus 1 uses a 5 pin connector and is labeled on the ECU as 'CAN 1/RS232'.If using this connector for CAN ensure the cable being used doesn't have Serial wires connected as this can



act as an aerial and prevent USB communications from working.

CAN 1/RS232 Connector

Pin Function Colour

1 Comms GND Brown

2 CAN1 L Green

3 CAN1 H White

4 RS232-RX Grey

5 RS232-TX Yellow

CAN bus 2 uses a 5 pin connector and is labeled on the ECU as 'CAN 2/OBD'.

CAN 2/OBD Connector

Pin Function Colour

1 GND Brown

2 CAN2 L Green

3 CAN2 H White

4 NC Grey

5 +14V Yellow

To learn more about CAN see PCLink help.

1.10 Known Issues

All plug-in ECUs are fully tested on a range of relevant vehicles, although there are often variations that havenot been tested. For this reason issues can arise.

WARNING: Always download the latest Installation Manual from linkecu.com and check the latest status ofknown issues before installing the ECU.

Please contact your nearest Link dealer when suspecting a compatibility issue.


Some vehicles don't have fuel temp sensors, if this is the case for your vehicle then turn off the fuel sensorinput or it's incorrect temperature reading will affect your fuelling.

WRXLink (04) - Subaru WRX & STI V10 04-06 and WRXLink (07) - Subaru WRX …linkecu.com/documentation/WRX10X.pdf · 1.2.3.1 Subaru Impreza WRX V1-10 ECU The G4X Subaru V1-10 Plug-In

Documents