Top Banner
CAT#3 . ADJUSTABLE FILLET WELD GAGE With unequal leg measurement feature Adjustable fillet weld gage is easy to use Measure fillet welds Measure weld throat thickness CAT#6 . AUTOMATIC WELD SIZE WELD GAGE For accurate calibration of butt and fillet type weld Check reinforcement Check the throat of fillet weld To determine the leg size of the fillet weld CAT#2. ECONOMY SINGLE PURPOSE HI-LO WELDING GAGE Available in standard or metric . Specify when ordering Root weld space-Internal misalignment Eliminates rejects, improves productivity CAT#9C. SKEW-T FILLET WELD GAGE Gage measures in English -metric Check acute size, obtuse side Check angle of vertical member Check obtuse size CAT#14. “MINI SUB” SOCKET WELD GAGE Check throat dimensions Check leg length Check all pipe schedule All stainless steel PIPE GAP – CLAMPS Pipe gap – clamps are designed to position and hold Open Butt pipe spools to one another while those pieces are tack welded The clamps are made of stainless steel and brass Interchangeable heads , shoes Brass stem to resist weld spatter Strictly inside alignment CAT18#. COMBO-WELDING GAGE Measure butt weld height Fillet weld leg- Root size Angle of preparation Fillet weld throat CAT#1. HI-LO WELDING GAGE INTERNAL ALIGNMENT Of pipe after fit-up/alignment, cuts radiographic rejects . Measures internal misalignment of pipe before and after tacking . Measurements read in standard one side ,metric opposite side CAT#10. PRE INSPECTION POCKET FILLET WELD GAGE New pocket measures 8 size fillets Throat size, plus allowable convexity All increments permanently engraved Available in standard and metric Handy key chain holes set together Material anodized aluminum Checks leg length CAT#8. 7PIECE FILLET WELD SET Gage now available with markings on both sides Made from stainless steel Check fillet throat size Check fillet leg size Upon request TAPER GAGES Check plate fit-up , flange fit- up Front size – standard Back size – metric There are many size-type taper gages 28A (1/32 to 5/8 ) 28B (5/8 to 1 3/16 ) 28C (1 3/16 to 2 ) CAT#12-1. WELDS, CWI INSPECTORS, INSTRUCTORS 13 essential tools in briefcase with lock& key size:18" x 12 1/2" x 3" Single purpose/economy Hi-Lo gage AWS gage - Adjustable fillet weld Skew T Fillet weld gage /Calculator Telescoping inspection mirror Magnifying glass with light Starrett micrometer w/ball. V-WAC gage-7PC Fillet weld set WTPS gage with block Standard Hi-Lo gage 6”starrett ruler –Bridge cam gage CAT#12-3. WELDS, CWI INSPECTORS, INSTRUCTORS 5 essential tools in wrap-around pouch size : 9" x 6 1/2" open Size : 6 1/2" x 4 1/4" closed Economy single Purpose Hi-Lo gage V-WAC plus 7 pc fillet combo set 6”generic (flexible/metal ) ruler Telescoping inspection mirror Penlight CAT#12-4. WELDS, CWI INSPECTORS, INSTRUCTORS 7 essential tools in AWS tool kit 6’’generic ruler V-WAC gage Micrometer Magnifying glass Dial caliper AWS gage 7 PC fillet weld gage CAT#4A . POCKET BRIDGE CAM GAGE Measure in metric or inch following Angle of preparation ,0 to 60 0 Excess weld metal(capping size) Depth of pitting, undercut by 1/32 Fillet weld throat, leg length Misalignment(high-low) CAT#4. BRIDGE CAM GAGE Measure in metric or inch following Angle of preparation ,0 to 60 0 Fillet weld throat size , length Excess weld metal Depth of undercut Depth of pitting, of pitting Misalignment (High Low ) CAT#13. COMBINATION 0"- 10" DIAL/PIT DEPTH GAGE Measuring range 0"-10". Graduations 0.001" Accuracy meets or exceeds federal specs Continuous dial for ½" travel Uniform pressure over full range Revolution Counter Interchangeable bases CAT#16. MINI FILLET WELD KEYS 11 different sizes in standard sizes with metric equivalent markings -1/8” to 1” Check weld leg size, dimension of skewed member Checking throat dimension CAT#12-2. WELDS, CWI INSPECTORS, INSTRUCTORS 7 essential tools in medium size kit with lock & key size: 3" x 8" x 3" Telescoping inspection mirror Standard Hi-Lo gage 6”starrett ruler V-WAC gage Starrett micrometer W/ball CAT#7. GAGE WTPS GAGE Measure Undercut 0.010” Deep undercut shall be no more than 0.010 in. (0.25 mm) deep when the weld is transverse to the primary stress in the part that is undercut.
11
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: Welding Gauge

CAT#3. ADJUSTABLE FILLET WELD GAGE With unequal leg measurement feature Adjustable fillet weld gage is easy to use Measure fillet welds Measure weld throat thickness

CAT#6. AUTOMATIC WELD SIZE WELD GAGE For accurate calibration of butt and fillet type weld Check reinforcement Check the throat of fillet weld To determine the leg size of the fillet weld

CAT#2. ECONOMY SINGLE PURPOSE HI-LO WELDING GAGE Available in standard or metric . Specify when ordering Root weld space-Internal misalignment Eliminates rejects, improves productivity

CAT#9C. SKEW-T FILLET WELD GAGE Gage measures in English -metric Check acute size, obtuse side Check angle of vertical member Check obtuse size

CAT#14. “MINI SUB” SOCKET WELD GAGE Check throat dimensions Check leg length Check all pipe schedule All stainless steel

PIPE GAP – CLAMPS Pipe gap – clamps are designed to position and hold Open Butt pipe spools to one another while those pieces are tack welded The clamps are made of stainless steel and brass Interchangeable heads , shoes Brass stem to resist weld spatter Strictly inside alignment

CAT18#. COMBO-WELDING GAGE Measure butt weld height Fillet weld leg- Root size Angle of preparation Fillet weld throat

CAT#1. HI-LO WELDING GAGE INTERNAL ALIGNMENT Of pipe after fit-up/alignment, cuts radiographic rejects . Measures internal misalignment of pipe before and after tacking . Measurements read in standard one side ,metric opposite side

CAT#10. PRE INSPECTION POCKET FILLET WELD GAGE New pocket measures 8 size fillets Throat size, plus allowable convexity All increments permanently engraved Available in standard and metric Handy key chain holes set together Material anodized aluminum Checks leg length

CAT#8. 7PIECE FILLET WELD SET Gage now available with markings on both sides Made from stainless steel Check fillet throat size Check fillet leg size Upon request

TAPER GAGES Check plate fit-up , flange fit- up Front size – standard Back size – metric There are many size-type taper gages 28A (1/32 to 5/8 ) 28B (5/8 to 1 3/16 ) 28C (1 3/16 to 2 )

CAT#12-1. WELDS, CWI INSPECTORS, INSTRUCTORS 13 essential tools in briefcase with lock& key size:18" x 12 1/2" x 3" Single purpose/economy Hi-Lo gage AWS gage - Adjustable fillet weld Skew T Fillet weld gage /Calculator Telescoping inspection mirror Magnifying glass with light Starrett micrometer w/ball. V-WAC gage-7PC Fillet weld set WTPS gage with block Standard Hi-Lo gage 6”starrett ruler –Bridge cam gage

CAT#12-3. WELDS, CWI INSPECTORS, INSTRUCTORS 5 essential tools in wrap-around pouch size : 9" x 6 1/2" open Size : 6 1/2" x 4 1/4" closed Economy single Purpose Hi-Lo gage V-WAC plus 7 pc fillet combo set 6”generic (flexible/metal ) ruler Telescoping inspection mirror Penlight

CAT#12-4. WELDS, CWI INSPECTORS, INSTRUCTORS 7 essential tools in AWS tool kit 6’’generic ruler V-WAC gage Micrometer Magnifying glass Dial caliper AWS gage 7 PC fillet weld gage

CAT#4A. POCKET BRIDGE CAM GAGE Measure in metric or inch following Angle of preparation ,0 to 600

Excess weld metal(capping size) Depth of pitting, undercut by 1/32 Fillet weld throat, leg length Misalignment(high-low)

CAT#4. BRIDGE CAM GAGE Measure in metric or inch following Angle of preparation ,0 to 600 Fillet weld throat size , length Excess weld metal Depth of undercut Depth of pitting, of pitting Misalignment (High – Low )

CAT#13. COMBINATION 0"- 10" DIAL/PIT DEPTH GAGE Measuring range 0"-10". Graduations 0.001" Accuracy meets or exceeds federal specs Continuous dial for ½" travel Uniform pressure over full range Revolution Counter Interchangeable bases

CAT#16. MINI FILLET WELD KEYS 11 different sizes in standard sizes with metric equivalent markings -1/8” to 1” Check weld leg size, dimension of skewed member Checking throat dimension

CAT#12-2. WELDS, CWI INSPECTORS, INSTRUCTORS 7 essential tools in medium size kit with lock & key size: 3" x 8" x 3" Telescoping inspection mirror Standard Hi-Lo gage 6”starrett ruler V-WAC gage Starrett micrometer W/ball

CAT#7. GAGE WTPS GAGE Measure Undercut 0.010” Deep undercut shall be no more than 0.010 in. (0.25 mm) deep when the weld is transverse to the primarystress in the part that is undercut.

Page 2: Welding Gauge

CAT# 4A . Pocket Bridge Cam Gage

ALL STAINLESS CONSTRUCTION

The following measurements are possible either in inches or millimeters . • Angle of preparation, 0º to 60º • Excess weld metal (capping size) • Depth of undercut by 1/32 • Depth of pitting by 1/32 • Fillet weld throat size ( 1/64 or .5 mm ) (Theoretical and Actual ) • Fillet weld length • Misalignment (high-low)

Excess Weld Metal Fillet Weld Throat Angle of Preparation

CAT# 4. Bridge Cam Gage The following measurements are possible either in inches or millimeters • Angle of preparation, 0º to 60º • Excess weld metal (capping size) • Depth of undercut • Depth of pitting • Fillet weld throat size • Fillet weld length • Misalignment (high-low)

Excess Weld Metal Fillet Weld Throat Angle of Preparation

Page 3: Welding Gauge

Check reinforcement of butt weld Check the throat of fillet weld

Check leg size of fillet weld

CAT# 3. Adjustable Fillet Weld Gage with unequal leg measurement feature

Adjustable Fillet Weld Gage is easy to use

To measure fillet welds place irregular curve edge flush to horizontal toe of weld so the straight edge is in line with the horizontal member.

To measure weld throat thickness place the 45º angle end flush to the horizontal and vertical members. Loosen the thumb screw and slide the pointer until it touches the face of the weld.

CAT# 6. Automatic Weld Size Weld Gage For Accurate Calibration of Butt And Fillet Type Welds.

Page 4: Welding Gauge

CAT# 9C. Skew-T Fillet Weld Gage with Calculator

Calculator: A handy compilation of mathematical relationships between leg length, throats, skew angles and inspection dimensions. A must for designers and inspectors. The perfect companion to the Skew-T Fillet Weld Gage

Checking angle of vertical member Checking weld acute side Checking weld obtuse side

Skew-T Fillet Weld Gage (Gage measures in English & Metric.)

CAT#18. Combo-Welding Gage

.Butt weld height

.Fillet weld throat

.Root size

.Fillet weld leg

.Angle of preparation

Gage is constructed from heavy gage 304 stainless

Fillet weld throat Root size Angle of preparation

The Combo-Welding Gage Can Measure in Metric Or Inch The Following

Page 5: Welding Gauge

CAT#14. "Mini Sub" Socket Weld Gage

CAT#7. Gage WTPS Gage Measure Undercut 0.010 Deep

Undercut shall be no more than 0.010 in. (0.25 mm) deep when the weld is transverse to the primary stressin the part that is undercut.

WTPS Gage is precision made from stainless steel all markings and dimensions are laser engraved for ease and clarity when reading. Gage set comes with a precision ground calibration block as shown above, each block has been surface ground to 0.0005 tolerance for exceptional accuracy.

Page 6: Welding Gauge

CAT#16. Mini Fillet Weld Keys

Checking Weld Leg Size Checking Throat Size Dimension Of Skewed Member

Checking Throat Size Dimension

CAT#8. 7 Piece Fillet Weld Set

Checking fillet throat size

Checking Fillet Leg SizeINDIVIDUAL BLADE SIZES/METRIC ONLY (WE ALSO SELL THE BLADES INDIVIDUALLY)

. 3mm -- 25mm . 4mm -- 22mm . 5mm -- 19mm . 10mm -- 11mm

. 6mm -- 16mm . 8mm -- 14mm . 9mm -- 12mm

Page 7: Welding Gauge

CAT# 2. Economy Single Purpose HI – LO Welding Gage

CAT#1. HI-LO Welding Gage Measures Internal Alignment Hi-Lo Welding Gage Measures Internal Alignment Of pipe after Fit-up/alignment, Cuts radiographic rejects. Measures internal Misalignment of pipe Before and after tacking.

Taper Gages

FRONT SIDE – STANDARD BACK SIDE - METRIC

There are many size-type taper gages

Page 8: Welding Gauge

.Checks Leg Length

.All Increments Permently Engraved

.Each Welder can Carry Set for Pre Inspection

.Material Anodized Aluminum

.New Pocket Size – Measures 8 Size Fillets

.Throat Size , Plus Allowable Convexity

.Available in Standard and Metric

.Handy Key Chain Holes Set Together

Measures throat (Allowable Convexity) Measures throat (theoretical) Measures leg length

CAT#10. PRE Inspection Pocket Fillet Weld Gage

CAT#13. Combination 0" - 10" Dial/Pit Depth Gage

• Measuring Range 0" – 10” • Graduations 0.001" • Accuracy meets or exceeds federal specs • Continuous dial for ½" travel • Revolution Counter • Uniform pressure over full range of travel • Complete with 6 extensions rods in fitted case • Micro probes for small diameter pits 0.062 to 0.025 • Interchangeable bases

Measures undercut socket weld

Measures undercut butt weld

Measures crown height butt weld

Page 9: Welding Gauge

Pipe Gap – Clamps

All Mini Pipe Gap-Clamps are designed to position and hold Open Butt pipe spools to one another while those pieces are tack welder. All are designed for use by a welder working alone. After tacking, the clamps Are loosened and removed by turning the handle to the right 900 and removing from between the pipe spools, the final weld can be achieved. These Mini Gap-Clamps have been redesigned for ease in aligning and gapping at the same time . The Mini Gap-Clamps come four to a set , which includes a handy belt pouch for ease in carrying the set to the work place, scaffolding , etc. The four clamps are positioned at equal intervals around the circumference of the pipe, the number required varies with the pipe diameter. Specification are shown below for each of the 3 types of clamps . Height is measured over the handle while thickness is that of the thickness component, front to rear , regardless of location. The design is field-proven , clamps are sturdy and with a minimum of maintenance , can be used over and over for years . The clamps are made of stainless steel and brass.

FEATURES .Interchangeable heads . Strictly inside alignment . Interchangeable shoes .Brass stem to resist weld spatter

SPECIFICATIONS TYPE1 TYPE2 Weight 1 lb .50 lb (1,8 kg) (0,45 kg) Height 5.25 in 3 in (216mm) (76mm) Width 3.5 in 1.5 in (89 mm) (38mm) Thickness 1 in 0.5 in (25 mm) (13 mm) Material: Stainless Steel & Brass Clamping Force: 1000 lb (454 kg) Application : Pipe and elbows up to in 8 in .(203 mm ) diameter .

TO USE PIPE CLAMPS 1. Select clamp size- Type 1 is designed for larger pipe up to 8 in (200 mm) diameter. And Type 2 for pipe up to 4

in(102mm) diameter. 2. Position pipes or pipe and elbow sections to be welded; slip head through gap between sections. 3. Pull upward with clamp handle. Keep handle parallel to outer pipe surface to insure proper alignment. 4. Tighten clamp with torque lever. CAUTION: DO NOT TIGHTEN WITH HANDLE NEVER EXCEED HAND TIGHT. TO REMOVE CLAMPS ALWAYS TURN KNURLED HANDLE TO THE RIGHT. 5. Install additional clamps as needed. Normally , the 4 clamps in a set are placed at 900 intervals but fewer may be used for smaller pipe and more may be used for larger pipe . 6. Tack weld to secure pipe section , turn knurled handle to the right to loosen and remove clamps.

With or Without Holders

NEW FEATURES • Brass Stem to Resist Weld Spatter • Strictly Inside Alignment • Interchangeable Shoes • Interchangeable Heads • All Stainless Steel

Page 10: Welding Gauge

Pipe Gap – Clamps

PARTS AND ACCESSORY LIST

Stem brass long , short. S/S top knurled handle. S/S knurled torque lever. S/S shoes. S/S shoes interchangeable. 1/8 replaceable head S/S. 3/32 replaceable head S/S. Canvas belt pouch small, large

Page 11: Welding Gauge

CAT#12-3. WRAP-AROUND POUCH 5 essential tools in wrap-around pouch size : 9" x 6 1/2" open - size : 6 1/2" x 4 1/4" closed V-WAC plus 7 pc fillet combo set. Single purpose/Economy Hi-Lo gage (either standard or metric ) 6”generic (flexible/metal ) ruler (metric or English) Telescoping inspection mirror (oval or round) Penlight

CAT#12-4. AWS TOOL KIT 7 essential tools in AWS tool kit ( Used by American welding society ) 6” generic (flexible / metal ) ruler Dial caliper/made in China (metric or standard ) Magnifying glass ( 2” DIA. – 1.5 power ) Micrometer / made in China 7 PC fillet weld gage V-WAC gage (standard or metric) AWS gage (standard or metric)

CAT#12. Welds, CWI Inspectors, Instructors Now You Can Design Your Inspection Tool Kit

CAT#12-2. MEDIUM SIZE KIT 7 essential tools in medium size kit with lock & key size: 3" x 8" x 3" V-WAC gage (metric or English) AWS gage (metric or English) Standard (All S/S ) Hi-Lo gage Starrett micrometer W/ball (metric or English) Telescoping inspection mirror (oval or round) 6”starrett ruler (metric or English) Magnifying glass with light.

CAT#12-1. BRIEFCASE WITH LOCK & KEY 13 essential tools in briefcase with lock & key size: 18" x 12 1/2" x 3" Single purpose/Economy Hi-Lo gage (comes either standard or metric) Magnifying glass with light - AWS gage (metric or English) V-WAC gage (metric or English) – Bridge cam gage 7PC. Fillet weld set - WTPS gauge with block Starrett micrometer w/ball (metric or English) Telescoping inspection mirror (oval or round) Adjustable fillet weld (metric or English) Skew-T-Fillet weld gage W/Calculator 6”starrett ruler (metric or English) Standard (All S/S ) Hi-Lo gage