Top Banner

Click here to load reader

User Guide - · PDF fileXAMPLE DEFINITION OF CORBEL REINFORCEMENT ... IRE FABRICS IN CROSS SECTION ... AutoCAD Structural Detailing - Reinforcement - User Guide page: v

Mar 19, 2018

ReportDownload

Documents

trantruc

  • User Guide

    Autodesk March 2010

  • 2010 Autodesk, Inc. All Rights Reserved. Except as otherwise permitted by Autodesk, Inc., this publication, or parts thereof, may not be reproduced in any form, by any method, for any purpose. Certain materials included in this publication are reprinted with the permission of the copyright holder. Disclaimer THIS PUBLICATION AND THE INFORMATION CONTAINED HEREIN IS MADE AVAILABLE BY AUTODESK, INC. AS IS. AUTODESK, INC. DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE REGARDING THESE MATERIALS. Trademarks The following are registered trademarks of Autodesk, Inc., in the USA and/or other countries: Autodesk Robot Structural Analysis, Autodesk Concrete Building Structures, Spreadsheet Calculator, ATC, AutoCAD, Autodesk, Autodesk Inventor, Autodesk (logo), Buzzsaw, Design Web Format, DWF, ViewCube, SteeringWheels, and Autodesk Revit. All other brand names, product names or trademarks belong to their respective holders. Third Party Software Program Credits ACIS Copyright 1989-2001 Spatial Corp. Portions Copyright 2002 Autodesk, Inc. Copyright 1997 Microsoft Corporation. All rights reserved. International CorrectSpell Spelling Correction System 1995 by Lernout & Hauspie Speech Products, N.V. All rights reserved. InstallShield 3.0. Copyright 1997 InstallShield Software Corporation. All rights reserved. PANTONE and other Pantone, Inc. trademarks are the property of Pantone, Inc. Pantone, Inc., 2002. Portions Copyright 1991-1996 Arthur D. Applegate. All rights reserved. Portions relating to JPEG Copyright 1991-1998 Thomas G. Lane. All rights reserved. Portions of this software are based on the work of the Independent JPEG Group. Portions relating to TIFF Copyright 1997-1998 Sam Leffler. Copyright 1991-1997 Silicon Graphics, Inc. All rights reserved. Government Use Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in FAR 12.212 (Commercial Computer Software-Restricted and DFAR 227.7202 (Rights in Rights)Technical Data and Computer Software), as applicable.

  • AutoCAD Structural Detailing - Reinforcement - User Guide page: i

    TABLE OF CONTENTS

    1. PROGRAM DESCRIPTION ......................................................................................................... 1 1.1. GENERAL DESCRIPTION OF THE PROGRAM .................................................................................. 1 1.2. STAGES OF WORK ON STRUCTURE PROJECT DRAWINGS .............................................................. 1 1.3. EXAMPLE OF LOADING A DRAWING CREATED IN ROBOT ............................................................ 2 1.4. OPTIONS AVAILABLE IN THE MENU ............................................................................................. 4 1.5. RIBBON .................................................................................................................................... 20

    2. CONFIGURATION ...................................................................................................................... 21 2.1. JOB PREFERENCES .................................................................................................................... 21

    2.1.1. Job preferences ................................................................................................................ 21 2.1.2. Units ................................................................................................................................ 22 2.1.3. Codes / Materials ............................................................................................................. 23 2.1.4. Options ............................................................................................................................ 25 2.1.5. Display (bars) .................................................................................................................. 26 2.1.6. Distributions (bars) ......................................................................................................... 28 2.1.7. Options (bars) .................................................................................................................. 28 2.1.8. Styles (bars) ..................................................................................................................... 30 2.1.9. Display (wire fabrics) ...................................................................................................... 30 2.1.10. Styles (wire fabrics) ......................................................................................................... 32 2.1.11. Styles (steel profiles) ........................................................................................................ 32 2.1.12. Styles (symbols) ............................................................................................................... 33

    2.2. PREFERENCES ........................................................................................................................... 34 2.2.1. Preferences ...................................................................................................................... 34

    3. OBJECT INSPECTOR ................................................................................................................. 37 3.1. OBJECT INSPECTOR DESCRIPTION ............................................................................................ 37 3.2. MODEL ..................................................................................................................................... 38 3.3. POSITIONS ................................................................................................................................ 40 3.4. STRUCTURAL DETAILING CENTER ............................................................................................ 41 3.5. PRINTOUTS ............................................................................................................................... 41

    4. TYPICAL STRUCTURES ........................................................................................................... 42 4.1. REINFORCEMENT / FORMWORK OF TYPICAL RC STRUCTURE ELEMENTS ................................... 42

    5. RULES APPLIED WHILE DEFINING REINFORCEMENT ................................................. 44 5.1. LOCATION OF A REINFORCING BAR IN A DRAWING ................................................................... 44 5.2. ANGLE OF HOOK BENDING ........................................................................................................ 44

    6. DEFINITION OF REINFORCEMENT - LONGITUDINAL REINFORCEMENT .............. 45 6.1. DEFINITION OF BAR REINFORCEMENT - LONGITUDINAL REINFORCEMENT ................... 45 6.2. STRAIGHT BAR ......................................................................................................................... 46 6.3. DEFINITION OF A STRAIGHT BAR (LONGITUDINAL REINFORCEMENT) ........................................ 47 6.4. STRAIGHT BAR WITH ANCHOR ELEMENT ................................................................................... 47 6.5. DEFINITION OF A STRAIGHT BAR WITH ANCHORS (LONGITUDINAL REINFORCEMENT) ............... 48 6.6. BENT BAR - TYPE 1 ................................................................................................................... 49 6.7. DEFINITION OF A BENT BAR (TYPE 1) - LONGITUDINAL REINFORCEMENT .................................. 50 6.8. BENT BAR - TYPE 2 ................................................................................................................... 50 6.9. BAR FROM DATABASE .............................................................................................................. 51 6.10. ARBITRARY SHAPE OF A BAR ................................................................................................ 53 6.11. REINFORCEMENT DESCRIPTION ............................................................................................ 54 6.12. USER DESCRIPTION - AUTOCAD PROGRAM MECHANISMS .................................................... 55 6.13. COMMANDS FROM THE COMMAND LINE - DEFINITION OF LONGITUDINAL REINFORCEMENT . 56 6.14. EXAMPLE OF DEFINITION OF LONGITUDINAL REINFORCEMENT ............................................. 57

    2010 Autodesk, Inc. All rights reserved

  • page: ii AutoCAD Structural Detailing - Reinforcement - User Guide

    7. DEFINITION OF REINFORCEMENT - TRANSVERSAL REINFORCEMENT ................ 59 7.1. DEFINITION OF BAR REINFORCEMENT - TRANSVERSAL REINFORCEMENT .................... 59 7.2. RECTANGULAR (CLOSED) STIRRUP ........................................................................................... 60 7.3. ROUND STIRRUP ....................................................................................................................... 61 7.4. PIN ........................................................................................................................................... 62 7.5. SHACKLE .................................................................................................................................. 63 7.6. BAR FROM DATABASE .............................................................................................................. 64 7.7. ARBITRARY BAR SHAPE ............................................................................................................ 66 7.8. DESCRIPTION OF REINFORCEMENT ........................................................................................... 67 7.9. COMMANDS FROM THE COMMAND LINE - DEFINITION OF TRANSVERSAL REINFORCEMENT ...... 68 7.10. EXAMPLE OF DEFINITION OF TRANSVERSAL REINFORCEMENT ...........................

Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.