Top Banner
1 The Indexing or Dividing Head Session 14
58
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: The Indexing or Dividing Head

1

The Indexing or Dividing Head

Session 14

Page 2: The Indexing or Dividing Head

2

Indexing (Dividing) Head• One of the important attachments for

milling machine

• Used to divide circumference of work piece into equally spaced divisions when milling gear teeth, squares, hexagons, and octagons

• Also used to rotate work piece at predetermined ratio to table feed rate

Page 3: The Indexing or Dividing Head

3

Index Head Parts

• Headstock with index plates• Headstock change gears• Quadrant

• Universal chuck• Footstock• Center rest

Page 4: The Indexing or Dividing Head

4

Index Head Parts

Page 5: The Indexing or Dividing Head

5

Section view of a dividing head

Page 6: The Indexing or Dividing Head

6

Index Head Parts• Universal chuck

• Threaded onto end of spindle

Page 7: The Indexing or Dividing Head

7

Index Head Parts• Footstock

• Used in conjunction with headstock to support work held between centers or in chuck

• May be adjusted longitudinally, raised or lowered off center, and tilted out of parallel

Page 8: The Indexing or Dividing Head

8

Index Head PartsAdjustable center rest

• Holds long, slender work between centers

Page 9: The Indexing or Dividing Head

9

Methods of Indexing

1. Direct

2. Simple

3. Compound

4. Differential

5. Angular

Page 10: The Indexing or Dividing Head

10

Direct Indexing

• Simplest form of indexing

• Performed by disengaging worm shaft from worm wheel by means of eccentric device in dividing head

• Used for quick indexing of workpiece when cutting flutes, hexagons, squares, etc.

Page 11: The Indexing or Dividing Head

11

Direct Indexing Divisions• Direct indexing plate usually contains three

sets of hole circles or slots: 24, 30, and 36• Number of divisions possible to index limited

to numbers that are factors of 24, 30, 36

Slots Direct indexing divisions

24 2 3 4 _ 6 8 _ __ 12 __ __ 24 __ __

30 2 3 _ 5 6 _ _ 10 __ 15 __ __ 30 __

36 2 3 4 _ 6 _ 9 __ 12 __ 18 __ __ 36

Page 12: The Indexing or Dividing Head

12

Example: Direct Indexing

• What direct indexing is necessary to mill eight flutes on a reamer blank?

Slots Direct indexing divisions

24 2 3 4 _ 6 8 _ __ 12 __ __ 24 __ __

30 2 3 _ 5 6 _ _ 10 __ 15 __ __ 30 __

36 2 3 4 _ 6 _ 9 __ 12 __ 18 __ __ 36

Since the 24-hole circle is the only one divisible by 8 (the required number of divisions), it is the only circle that can be used in this case.

Never count the hole or slot in which the index pin is engaged.

Page 13: The Indexing or Dividing Head

13

Milling a Square with Direct Indexing

1. Disengage worm and worm shaft by turning worm disengaging shaft lever if dividing head is so equipped

2. Adjust plunger behind index plate into the 24-hole circle or slot

3. Mount workpiece in dividing head chuck or between centers

4. Adjust cutter height and cut first side

Page 14: The Indexing or Dividing Head

14

5. Remove plunger pin using plunger pin lever

6. Turn plate attached to dividing head spindle one-half turn and engage plunger pin

7. Take second cut

Milling a Square with Direct Indexing

Page 15: The Indexing or Dividing Head

15

8. Measure work across flats and adjust work height if required

9. Cut remaining sides by indexing every six holes until all surfaces cut

10.Check for finish size

Milling a Square with Direct Indexing

Page 16: The Indexing or Dividing Head

16

Simple Indexing

• Work positioned by means of crank, index plate, and sector arms

• Worm attached to crank must be engaged with worm wheel on dividing head spindle

• 40 teeth on worm wheel • One complete turn on index crank cause

spindle and work to rotate one-fortieth of a turn (ratio of 40:1)

Page 17: The Indexing or Dividing Head

17

Simple Indexing

• Calculating the indexing or number of turns of crank for most divisions, simply divide 40 by number of divisions to be cut or,

40Indexing =

N

Page 18: The Indexing or Dividing Head

18

Simple Indexing

• The indexing required to cut eight flutes:

crankindex of turns full 58

40

• The indexing required to cut seven flutes:

crankindex of turns 7

55

7

40

The five-sevenths turn involves use of an index plate and sector arms.

Page 19: The Indexing or Dividing Head

19

Index Plate and Sector Arms

• Index plate• Circular plate provided with series of

equally spaced holes into which index crank pin engages

• Sector arms• Fit on front of plate and may be set to any

portion of a complete turn

Page 20: The Indexing or Dividing Head

20

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /21

So, 5 full turns plus15 holes on 21 holecircle!

15

Page 21: The Indexing or Dividing Head

21

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /49

So, 5 full turns plus35 holes on 49 holecircle!

35

Page 22: The Indexing or Dividing Head

22

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /28

So, 5 full turns plus20 holes on 28 holecircle!

20

Page 23: The Indexing or Dividing Head

23

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /42

So, 5 full turns plus30 holes on 42 holecircle!

30

Page 24: The Indexing or Dividing Head

24

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /49

So, 5 full turns plus35 holes on 49 holecircle!

35

Page 25: The Indexing or Dividing Head

25

Cutting Seven Flutes

1. Mount B&S Plate 2 index plate on dividing head

2. Loosen index crank nut and set index pin into hole on 21-hole circle

3. Tighten index crank nut and check to see that the pin enters hole easily

4. Loosen setscrew on sector arm5. Place narrow edge of left arm against

index pin

Page 26: The Indexing or Dividing Head

26

6. Count 15 holes on 21-hole circle• Do not include hole in which index crank

pin is engaged.

7. Move right sector arm slightly beyond fifteenth hole and tighten sector arm setscrew

8. Align cutter with work piece

9. Start machine and set cutter to top of work by using paper feeler

Cutting Seven Flutes

Page 27: The Indexing or Dividing Head

27

10.Move table so cutter clears end of work

11.Tighten friction lock on dividing head before making each cut and loosen lock when indexing for spaces

12.Set depth of cut and take first cut

13.After first flute has been cut, return table to original starting position

Cutting Seven Flutes

Page 28: The Indexing or Dividing Head

28

14.Withdraw index pin and turn crank clockwise five full turns plus the 15 holes indicated right sector arm

• Release index pin between 14th and 15th holes and gently tap until it drops into 15th hole

15.Turn sector arm farthest from pin clockwise until it is against index pin

Cutting Seven Flutes

Page 29: The Indexing or Dividing Head

29

16.Lock dividing head; continue machining and indexing for remaining flutes

Cutting Seven Flutes

The arm farthest from the pin is held and turned. If the arm next to the pin were held and turned, the spacing between both sector arms could be increased when the other arm hits the pin. This could result in an indexing error not noticeable until the work was completed.

Page 30: The Indexing or Dividing Head

30

Angular Indexing

• Setup for simple indexing may be used• Must calculate indexing with angular

distance between divisions instead number of divisions

• One complete turn of index crank turns work 1/40 of a turn• 1/40 of 360º equals 9 degrees

9

required degrees of no. degrees in Indexing

Page 31: The Indexing or Dividing Head

31

Angular Indexing

Calculate indexing for 45º

59

45 Indexing

5 complete turns

Page 32: The Indexing or Dividing Head

32

Angular Indexing

Calculate indexing for 60º

3

26

9

60 Indexing

6 full turns plus 12 holes on 18 hole circle

Page 33: The Indexing or Dividing Head

33

Angular Indexing

Calculate indexing for 24'

Divide 24'/540' = 4/90 4/90 = 1/22.5

1 hole on a 22.5 hole circle

The nearest is a 23 hole circle. Indexing would be 1 hole on a 23 hole circle with a slight error (approximately 1/2 minute). A need for higher accuracy requires differential indexing.

Page 34: The Indexing or Dividing Head

34

Angular Indexing

Calculate indexing for 24º30'• First, convert angle into minutes

(24 x 60') = 1440' now add 30' = 1470‘Convert 9° to minutes 9°x60’ = 540’

Divide 1470'/540' = 2 13/18

2 full turns and 13 holes on 18 hole circle

Page 35: The Indexing or Dividing Head

35

Differential Indexing

• Used when 40/N cannot be reduced to a factor of one of the available hole circles

• Index plate must be revolved either forward or backward part of a turn while index crank turned to attain proper spacing (indexing)• Change of rotation effected by idler gear or

gears in gear train

Page 36: The Indexing or Dividing Head

36

Differential Method• Number chosen close to required

divisions that can be indexed by simple indexing

• Example: Assume index crank has to be rotated 1/9th of a turn and only 8-hole circle• Crank moved 1/9th, index pin contacts plate

at spot before first hole• Exact position would be the difference

between 1/8th and 1/9th of a revolution of the crank

Page 37: The Indexing or Dividing Head

37

Differential Method cont.

72

1

72

8

72

9

9

1

8

1

one-seventy-second of a turn short of first hole

Since there is no hole at this point, it is necessary to cause plate to rotate backward by means of change gears one-seventy-second of a turn of pin will engage in hole.

Page 38: The Indexing or Dividing Head

38

Method of Calculating the Change Gears

gear (worm) driven

gear (spindle) driver

A

40 x N) -(A ratio gear Change

A = approximate number of divisionsN = required number of divisions

If A is greater than N, resulting fraction is positive andthe index plate must move in same direction as crank (clockwise). This positive rotation uses an idler gear.

If N is greater than A, resulting fraction is negative andindex plate must move counterclockwise. This negativerotation required use of two idler gears.

Page 39: The Indexing or Dividing Head

39

Gearing

• Simple• One idler for positive rotation of index

plate and two idlers for negative rotation

• Compound• One idler for negative rotation of index

plate and two idlers for positive rotation

Page 40: The Indexing or Dividing Head

40

Example:

Calculate the indexing and change gears requiredfor 57 divisions. The change gears supplied with the dividing head are as follows: 24, 24, 28, 32, 40, 44, 48, 56, 64, 72, 86The available index plate hole circles are as follows:Plate 1: 15, 16, 17, 18, 19, 20Plate 2: 21, 23, 27, 29, 31, 33Plate 3: 37, 39, 41, 43, 47, 49

57

40

N

40 Indexing

No 57 hole circle so selectnumber close to 57

7

5

56

40

5/7 would be 15 holes on 21-hole circle

Choose plate 2: 21 holes

Page 41: The Indexing or Dividing Head

41

Example: continued

The fraction is negative and simple gearing is to be used, the index plate rotation is counterclockwise and two idlers must be used.

gear) (worm 56

gear) (spindle 40

8

8x

7

5- gears Change

7

5

56

40 x

56

40x 57) - (56

A

40x N) -(A ratio Gear

1

Page 42: The Indexing or Dividing Head

42

• For indexing 57 divisions, a 40-tooth gear is mounted on the dividing head spindle and a 56-tooth gear is mounted on the worm shaft.

• Index idlers must be used. plate rotation is negative and two

• After proper gears installed, the simple indexing for 56 divisions should be followed

Example: continued

Page 43: The Indexing or Dividing Head

43

Wide-Range Dividing Head• Possible for 2 to 400,000 divisions• Large index plate contains 11 hole

circles on each side• Small index plate mounted in front of

large, contains a 54 hole and a 100-hole circle

• 40:1 ratio between worm and dividing head spindle

Page 44: The Indexing or Dividing Head

44

A – large index plate

B - crank

C – small index plate

D - crank G – gear housing

Page 45: The Indexing or Dividing Head

45

Indexing for Divisions

• One turn of small crank drives index head spindle 1/100 of 1/40, or 1/4000 of a turn• Ratio of large index crank to dividing head

40:1• Ratio of small index crank 100:1

Page 46: The Indexing or Dividing Head

46

Indexing for Divisions

• One hole on 100-hole circle of small index plate C = 1/100 x 1/4000 • 1/400,000 of a turn

• Formula for indexing divisions = 400,000/N

Page 47: The Indexing or Dividing Head

47

Indexing for Divisions

No. of turns of large index crank

No. of holes on 100-hole circle of large plate

No. of holes on 100-hole circle of small plate

4 0  0 0  0 04 04 0  0 0

NNumber of Divisions

x x

Page 48: The Indexing or Dividing Head

48

Indexing for Divisions

For 1250 divisions 400000/1250

40|00|00 1250

Since ratio of large index crank is 40:1 , any number that divides into 40 (first two numbers) represents full turns of large index crank

No. of turnsof large Index Crank = 0

One hole on 100-holecircle produces 1/4000of a turn; any numberdivides into 4000 are

indexed on large plate

20

No. turns100-hole=Large plate

3 20 holes on the 100-hole circle

small plate

4 0  0 0  0 04 04 0  0 0

N

30

Zero turns of large crank, 3 turns of 100-hole large plate and 20 holes on 100-hole small plate

Page 49: The Indexing or Dividing Head

49

Angular Indexing with the Wide-Range Divider

• Indexing in degrees, minutes, and seconds easily accomplished

• Both large and small index cranks set on 54-hole circle of each plate• Each space on 54-hole large plate will

cause dividing head spindle to rotate 10'• Each space on 54-hole small plate will

cause work to rotate 6"

Page 50: The Indexing or Dividing Head

50

Angular Indexing: cont.

plate) small on (indexed 6

N Seconds

plate) large on (indexed 10

N Minutes

plate) large on (indexed9

N Degrees

Example: Index for an angle of 17º36'18"

turns 9

81

9

17

One full turn + 48 holes on large plate

6' of r with3 10

36

3 holes on large plate

636

378

6

18x60)(6'

One full turn + 9 holes on small plate

One full turn + 51 holes on large plate

Page 51: The Indexing or Dividing Head

51

Linear Graduating

• Operation of producing accurate spaces on piece of flat or round stock

• Align workpiece parallel with table travel

• Dividing head spindle geared to lead screw of milling machine for accurate longitudinal movement of table• 1 revolution of index crank = 1/40th

revolution of spindle and lead screw

Page 52: The Indexing or Dividing Head

52

Linear Graduating: cont.• Rotation of lead screw (4 threads per

inch) would cause table to move 1/40th x 1/4th or 1/160th = .0025 in.

• Formula for calculating indexing for linear graduations in thousandths of an inch

.00625

N Example: Movement of table .001 in

turns

41

6

1

.00625

.001

4 holes on 25-hole circle

Page 53: The Indexing or Dividing Head

53

• If lead screw of metric milling machine has pitch of 5mm, 1 turn of index crank would move table 1/40th of 5 mm or 0.125 mm

• Point of toolbit used for graduating generally ground to V-shape

Linear Graduating: cont.

Page 54: The Indexing or Dividing Head

54

• Uniformity of line length controlled by accurate movement of crossfeed handwheel

• Uniformity of line width maintained if work held absolutely flat and table height never adjusted

Linear Graduating: cont.

Page 55: The Indexing or Dividing Head

Compound Indexing

Used when no. of div. is out of range of S.I.

It involves in 2 stages

1 By turning crank in one dirn.

2 by turning index plate& crank both in same or reverse direction

55

Page 56: The Indexing or Dividing Head

Procedure

56

Page 57: The Indexing or Dividing Head

57

Page 58: The Indexing or Dividing Head

58

Index Head Parts• Swiveling block

• Mounted in base enables headstock to be tilted from 5º below horizontal to 10º beyond vertical

• Spindle• Mounted in swiveling block with 40-tooth

worm wheel, meshes with worm• Worm

• Right angle to spindle, connected to index crank

• Direct indexing plate• Engaged by pin and attached to front of

spindle