Tastatura Lcd Cerber Kp 16lcdl b w

8/15/2019 Tastatura Lcd Cerber Kp 16lcdl b w

http://slidepdf.com/reader/full/tastatura-lcd-cerber-kp-16lcdl-b-w 1/60

Ce r b e r C6 1 21 2 - Z o n e a n d 2 - P a r t i t i o n B u r g l a r y Co n t r o l Pa n e l

for y o u r h o m e a n d o f f i ce

Hook-Up & Programming Book[draft]25.10.2006/ version 1.9 B











6

1.4. ConnectorsThe following connectors can be found on the control panel PCB:

AUX-, AUX+Connectors for auxiliary power supply

These terminals are the power supply for keypads, PIR detectors and other active devices in the system, which require power from a 13.8Vcc supply).

The maximum load on these terminals cannot exceed 2 A . P a y a t t e n t i o n t o p o l a r i t y ! Y (yellow), G (green)Keypad communication connectors

PGM1, PGM2PGM1 - “ open collector ” output 1 with negative trigger (NPN); maximum current capability: 50mA (at +13.8Vcc).

PGM2 - “ open collector ” output 2 with negative trigger (NPN); maximum current capability: 50mA (at +13.8Vcc).

BELL +

Siren output “BELL+” is a positive trigger output (PNP), with 2K2 EOL supervision resistor .

Z1, COM, Z2, Z3, COM, Z4, Z5, COM, Z6.Terminals for control panel hardwired zones; see the general mounting diagram and the zones wiring diagrams.

PHONEPhone set connectors.

LINETelephone line connectors



















15

After choosing the first set of attributes, press [#] key to confirm and the keypad buzzer will sound 3 beeps. Then, the ATTRIBUTES 2 set is displayed. Press[1] to [8] keys and the related attributes will be activated/deactivated.

After choosing second attribute set, press [#] key again to confirm and the keypad buzzer will sound 3 beeps. Then, the ATTRIBUTES 3 set is displayed. Press[1] and [2] keys and the related attributes will be activated/deactivated.

After choosing the third set of attributes, press [#] key to confirm , the keypad buzzer will sound 6 confirmation beeps and the panel exits the section, waiting

for a new command to enter another section or [#] key to exit the main programming menu. Section [02] - Definitions for zone 2Follow the same procedure as for zone 1 (section [01]).

Section [03] - Definitions for zone 3Follow the same procedure as for zone 1 (section [01]).








Section [11] - Definitions for zone 11

Follow the same procedure as for zone 1 (section [01]).


Section [17]: Zone descriptors programming

Edit zone: , type one 2 digit numberfor zone (i.e. zone 12)

Edit zone: 12 _



16

For each zone you can enter up to 16 characters descriptor. Some general rules for how to use the keypad and the caracters associated to the keys are the following:

- Press a number key, [0] to [9], repetedly until the desired character appears.All the characters available under a number key are printed on the key(except for the symbols) and are presented in the next table;

- if the next letter you want is located on the same key as the present one, waituntil the cursor moves one position to the right, or press the [>] key and thenkey in the letter;

- if you make a mistake, press the [<] key to remove the character to the leftof the cursor;

- if you want to program one descriptor with a length of less than 16characters, by pressing the key [#] the word is stored in the KP’s memoryand on the screen you can see the “Edit zone: “ message. By pressing onceagain the [#] key you can end zone descriptors programming (section 17). Byentering a 2 digit zone number you can continue by editing the zonedescriptor that you indicated.

Keypressed Characters associated to the keys

[1] , . : > = < ? 1

[2] A B C 2[3] D E F 3[4] G H I 4[5] J K L 5[6] M N O 6[7] P Q R S 7[8] T U V 8[9] W X Y Z 9[0] (space) ! “ 0[*] not used for descriptors editing

[#] used to confirm the descriptor and save it intothe keypad memory

[CODE] change between capital and small letters[<] used to delete one character (Backspace)

[STAY] not used for descriptors editing[BYPS] not used for descriptors editing[INST] not used for descriptors editing

[>] not used for descriptors editing

Section [018]: Playback of voice messages (MPV16/DTMF module must be installed and one speaker connected to SPEAKER terminals)

After selecting the programming section [018] KP126P LED are the following: ARMED A – ON, READY A – ON, SYSTEM – flashing, and zone LED 11 – ON. Message number that isplayed, consisting of 2 the 2 digits are displayed on LED keypads one short flash of zone LEDs for tens, and 2 short flashes for the units.

There are 94 voice messages that can be played using programming section [018]. While the message is played, the red BUSY LED is ON. The English voice message text transcriptionand the maximum length of these are presented in the following table:

Play msg ? , type one 2 digit numberfor message number

(i.e. 07)

Play msg 7



















































Notes:

1. By default, the second panel account is 0000.



42

1st Rep.FormatDTMF AdemcoCID

Choice Sect:2nd Rep.FormatDTMF AdemcoCID

2. In order to identify itself to CS2, the control panel will use the second panel account, which is set in this section, only if the split (or double) reporting option was set and only while thecontrol panel is dialing the 2 -nd CS phone number.

Section [49]: 1 st Reporting Format / 2 nd Reporting FormatEnter 2 groups of 2 digits, the first 2-digit group being the type of the format for CS1 transmission and the second 2-digit group being the type of the format for CS2 transmission.

Formatcode 2 nd line message Description

[00] 10pps4x2p1.4/1.8 10PPS,4x2 with parity,1400Hz kisson,1800Hz data


[02] 10pps4x2 1.4/1.8 10PPS,4x2 no parity,1400Hz kisson,1800Hz data








[22] 20pps4x2 1.4/1.8 20PPS,4x2 no parity,1400Hz kisson,1800Hz data[23] 20pps4x2 2.3/1.8 20PPS,4x2 no parity,2300Hz kisson,1800Hz data













[10] DTMF4x2 AdemcoEx DTMF, 4x2 Ademco Express

[90] DTMF AdemcoCID DTMF Ademco ContactID

, type one 2 digit numberor[#]


Notes:

1. Switching format types between Contact ID and 4x2 formats is recommended to be performed without any active CS transmission.st st



43

PGM1 TypeReset Monost


Choice Sect:

2. Any time when the control panel is dialing the 1 -st CS phone number, the panel will report in the 1 -st reporting format which is set in this section, irrespective of way the alternate or splitreporting option was set.

3. The panel will report in the 2 -nd reporting format which is set in this section, only if the split (or double) reporting option was set and only while the control panel is dialing the 2 -nd CS phonenumber.

Section [50]: “Ding Time” / “Ding Pause”Enter 2 digits (HEX digits may be used) in order to set the “ding time and pause”, the first digit multiplied by 65ms being “ding time” and the second digit multiplied by 65msbeing “ding pause”.

The keypad buzzer will sound 6 confirmation beeps after the 2-digit group and the panel exits the section, waiting for a new command to enter another section.

To exit the “main programming menu”, press [#] key.

Section [51]: Types for PGM1 to PGM6 OutputsWhile system is being within “main programming menu” , to set the type of programmable PGM1 to PGM6 outputs, select section [51] and then enter 6 groups of 2 digits each:

T h e f i r st g r o u p i s s et t i n g t h e P GM 1 t y p e ; t h e s e c o n d g r o u p i s s et t i n g t h e P G M 2 t y p e and so on.

After the first 2 digits were entered, the keypad buzzer will sound 3 beeps and after the last 2 digits were entered, the keypad buzzer will sound 6 confirmation beeps and the panelexits the section, waiting for a new command to enter another section.

Press [#] key instead of the 2 corresponding digits if the type of one of the programmable outputs isn’t to be changed.


Ding time9

Ding pause9


Choice Sect:, type one 1 digit numberor[#]







, type one 2 digit numberor

[#]



, type one 2 digit numberor

[#]



















The keypad buzzer will sound 3 beeps after each 3-digit group and 6 beeps after the last one.

Note: For each these times any value from 000 to 999 may be entered, but the panel will automatic adjust the introduced value by modulo 256 and will record the result in memory asprogrammed value. If any result of adjustment is 0, then the „guardian round period” and/or the „warning guardian round time” will be as they were set for 1 minute!



53

AutoArmTime AUnprogrammed

AutoDisarmTime AUnprogrammed

Choice Sect:

AutoArmTime BUnprogrammed AutoDisarmTime BUnprogrammed Choice Sect:

RoundStartTimeUnprogrammed

RoundFinishTimeUnprogrammed

Choice Sect:

Section [78]: Autoarming / Autodisarming Moments for Partition A (hour: minute / hour: minute)In order to establish the daily moments when the partition A is arming/disarming automatically, enter the hour (00 to 23) and minute (00 to 59) for arming moment and the hour (00to 23) and minute (00 to 59) for disarming moment.

The keypad buzzer will sound 3 beeps after each 2-digit group and 6 beeps after the last one. Then the panel exits the section and will wait for a new command.


Section [79]: Autoarming / Autodisarming Moments for Partition B (hour: minute / hour: minute)In order to establish the daily moments when the partition B is arming/disarming automatically, enter the hour (00 to 23) and minute (00 to 59) for arming moment and the hour (00to 23) and minute (00 to 59) for disarming moment.



Section [80]: Moments for Starting / Finishing the Guardian Rounds (hour: minute / hour: minute)In order to establish the daily moments when the guardian rounds are starting/finishing automatically, enter the hour (00 to 23) and minute (00 to 59) for starting moment and thehour (00 to 23) and minute (00 to 59) for finishing moment.



, type two 2 digit numbersor[#]











To exit the “main programming menu” press [#] key



56

1st PerTST01:00

Choice Sect:

InactivityTime A

03:00

InactivityTime B

03:00

Choice Sect:

UP/DW C612 psw0000

UP/DW PC psw0000

To exit the main programming menu , press [#] key.

Section [89]: Hour / Minute for First Periodical testEnter 2 groups of 2 digits, the first 2 digits for hour (00 to 23) and the second 2 digits for minute (00 to 59) when the system will send the first periodical test.



Section [90]: “Inactivity Time” after that the partitions will autoarm (hours & minutes / hours & minutes)Enter 4 groups of 2 digits:

- the first 2 digits for number of hours (00 to 99) and the second 2 digits for number of minutes (00 to 99) after that the partition A will auto arm if no motion will be detectedin the area;

- the third 2 digits for number of hours (00 to 99) and the fourth 2 digits for number of minutes (00 to 99) after that the partition B will auto arm if no motion will be detectedin the area;



Note: If in this section, one of the 2 groups of 2 digits are set both with value 0, then the corresponding partition will try to auto arm after every second if no activity will be detected in the area.

Section [91]: Panel Identification Code within upload/downloadEnter 4 digits (HEX digits are NOT allowed), to identify the control panel within upload/download process.

[x][x][x][x] (default value is [0000] )

After entering the 4 digits, keypad buzzer will sound 6 beeps and the panel will exit the section, waiting for a new command to enter anothersection.


Section [92]: PC Identification Code within upload/downloadEnter 4 digits (HEX digits are NOT allowed), to identify the control panel within upload/download process.

[x][x][x][x] (default value is [0000] )










59

Stop CommSection [99]: Cancellation of any Phone Line Communication[* ][ 8 ][ Installer’s programming code ][ 99] Command allows to the installer to cut-off any phone communication when he is carrying out a test.

[*][8][Master Code][99][#] Command allows to the “master” user to stop the voice/sound reporting and communication between panel and PC,without stopping communication to the “ central station ”.



Tastatura Lcd Cerber Kp 16lcdl b w

Documents