STR-K700 · SERVICE MANUAL Sony Corporation Home Audio Division Published by Sony Techno Create Corporation US Model Canadian Model FM STEREO FM-AM RECEIVER 9-887-073-01 2006A1678-1
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SERVICE MANUAL
Sony CorporationHome Audio DivisionPublished by Sony Techno Create Corporation
• STR-K700 is the tuner and the amplifiersection in HT-DDW700.
Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol are trademarks ofDolby Laboratories.“DTS” and “DTS Digital Surround” are registered trademarks ofDigital Theater Systems, Inc.
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:(Models of area code US only)With 6 ohm loads, both channels driven, from 120 – 20,000 Hz; rated 85 watts per channel minimum RMS power, with no more than 0.7% total harmonic distortion from 250 milliwatts to rated output.
Amplifier sectionPower Output1)
Models of area code US(6 ohms 1 kHz, THD 10%)FRONT2) : 133 W/chCENTER2): 133 WSUR2) : 133 W/ch(6 ohms 100 Hz, THD 10%)SUB WOOFER2): 135 W
3) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down DIMMER, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.
SA-CD/CD, DVD, VIDEO 1, 2
Sensitivity: 800 mVImpedance: 50 k ohms
DVD (Coaxial) Sensitivity: –Impedance: 75 ohms
VIDEO 2 (Optical) Sensitivity: –Impedance: –
Gain levels ±6 dB, 1 dB step
— Continued on next page —
2
STR-K700
Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 °C.Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
About area codesThe area code of the receiver you purchased is shown on the lower right portion of the rear panel (see the illustration below).
Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”.
CENTER FRONTLR
LR
+ +
Area code
MODEL IDENTIFICATION– Rear Panel –
Model Part No.
US model 2-661-458-0[]
Canadian model 2-661-458-1[]
Parts No.
GeneralPower requirements
Power consumption
Power consumption (during standby mode)0.2 W
Dimensions (w/h/d) (Approx.)17 × 5 6/8 × 12 1/8 inches including projecting parts and controls
Mass (Approx.) 16 lb 9 oz
120 V AC, 60 Hz
Area code Power consumption
US 210 W
Canadian 290 VA
Design and specifications are subject to change without notice.
3
STR-K700
TABLE OF CONTENTS
1. GENERAL ................................................................... 4
2. TEST MODE ............................................................... 10
3. DIAGRAMS3-1. Block Diagram – MAIN Section – .................................. 123-2. Block Diagram – DISPLAY/POWER Section – ............. 133-3. Printed Wiring Board – DIGITAL Board (Side A) – ...... 143-4. Printed Wiring Board – DIGITAL Board (Side B) – ...... 153-5. Schematic Diagram – DIGITAL Board (1/3) – .............. 163-6. Schematic Diagram – DIGITAL Board (2/3) – .............. 173-7. Schematic Diagram – DIGITAL Board (3/3) – .............. 183-8. Printed Wiring Board – MAIN Board – ......................... 193-9. Schematic Diagram – MAIN Board (1/3) – ................... 203-10. Schematic Diagram – MAIN Board (2/3),
5. ELECTRICAL PARTS LIST .................................. 36
SAFETY CHECK-OUTAfter correcting the original service problem, perform the followingsafety check before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage.Check leakage as described below.
LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes.).Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers’ instructions to use theseinstruments.
2. A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63Trd are examplesof a passive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2 V AC range are suitable. (SeeFig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 kΩ0.15 µFACvoltmeter(0.75 V)
To Exposed MetalParts on Set
Earth Ground
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SURLES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DESPIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DEFONCTIONNEMENT. NE REMPLACER CES COM- POSANTSQUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONTDONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTSPUBLIÉS PAR SONY.
4
STR-K700SECTION 1GENERAL This section is extracted
from instruction manual.
Front panel
Receiver
?/1
2 6 7 8
qf qd
3 4 51
qs 90qa
Name FunctionA ?/1 Press to turn the receiver
on or off.
BDIMMER Press to adjust the brightness of the display.
CSLEEP Press to activate the Sleep Timer function and the duration which the receiver turns off automatically.
D 2CH Press to select 2CH STEREO mode.
EDisplay The current status of the selected component or a list of selectable items appears here.
FDISPLAY Press to select information displayed on the display.
G INPUT MODE Press to select the input mode when the same components are connected to both digital and analog jacks.
HMASTER VOLUME
Turn to adjust the volume level of all speakers at the same time.
I INPUT SELECTOR
Turn to select the input source to playback.
JRemote sensor Receives signals from remote commander.
KMOVIE,MUSIC
Press to select sound fields (MOVIE, MUSIC).
LA.F.D. Press to select A.F.D. mode.
M PHONES jack Connects to a headphone.
NAUTO CAL MIC jack
Connects to the supplied ECM-AC2 optimizer microphone for the Auto Calibration function.
Name Function
5
STR-K700
About the indicators on the display
L C RSL S SR
LFE SP DIGITAL PRO LOGIC II DTSD.RANGE STEREO MONOSLEEP OPT COAX
; ; MEMORYSW
0 9qd
qf
qaqs
21 43 5 6 7
8
Name Function
A SW Lights up when audio signal is output from the SUB WOOFER jack.
B LFE Lights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced.
C SP Lights up when the receiver is turned on. This indicator does not light up if a headphone is connected to the PHONES jack.
D;DIGITAL Lights up when Dolby Digital signals are input.NoteWhen playing a Dolby Digital format disc, be sure that you have made digital connections and that INPUT MODE is not set to “ANALOG”.
E; PRO LOGIC (II)
“; PRO LOGIC” lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. “; PRO LOGIC II” lights up when the Pro Logic II Movie/Music decoder is activated.NoteDolby Pro Logic and Dolby Pro Logic II decoding do not function for DTS format signals.
FDTS Lights up when DTS signals are input. NoteWhen playing a DTS format disc, be sure that you have made digital connections and that INPUT MODE is not set to “ANALOG”.
GMEMORY Lights up when a memory function, such as Name Input, Preset Memory , etc., is activated.
H Preset station indicators
Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations.
I Tuner indicators
Lights up when using the receiver to tune in radio stations,
etc.
JD.RANGE Lights up when dynamic range compression is activated.
KCOAX Lights up when INPUT MODE is set to “AUTO” and the source signal is a digital signal being input through the COAXIAL jack, or when INPUT MODE is set to “COAX IN” .
LOPT Lights up when INPUT MODE is set to “AUTO” and the source signal is a digital signal being input through the OPTICAL jack, or when INPUT MODE is set to “OPT IN”.
M SLEEP Lights up when the Sleep Timer function is activated.
Name Function
NPlayback channel indicators
LRCSLSRS
The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound.Front LeftFront RightCenter (monaural)Surround LeftSurround RightSurround (monaural or the surround components obtained by Pro Logic processing)Example:Recording format (Front/Surround): Dolby Digital 3/2.1Sound Field: A.F.D. AUTO
L C RSL SR
SW LFE
6
STR-K700
Rear panel
SUBWOOFER SURROUND
DVD IN
SPEAKERSSAUDIO IN
DVDAUDIO IN
VIDEO 2AUDIO IN
VIDEO 1AUDIO IN LR
LR
+ +
DIGITALOPTICAL
VIDEO 2IN
COAXIAL
AM
ANTENNA
CENTER FRONTLR
LR
+ +
R R
LL
L
R
1 33 442
ADIGITAL INPUT section
OPTICALIN jack
Connects to a DVD player, etc. The COAXIAL jack provides a better quality of loud sound .
COAXIAL IN jack
BANTENNA section
FMANTENNA
Connects to the FM wire antenna supplied with this receiver .
AM ANTENNA
Connects to the AM loop antenna supplied with this receiver .
CAUDIO INPUT section
AUDIO IN jack
Connects to a CD player, etc.
DSPEAKER section
Connects to the speakers and sub woofer.
White (L)
Red (R)
7
STR-K700
You can use the supplied remote RM-AAU006 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate.
Remote commander
AV ?/1 (on/standby) switch
TV ?/1, ?/1 (on/standby) switch
1 2 3
4 6
7 8
0/10 ENTER
9
SYSTEM STANDBY
TV/VIDEOSLEEP
AUTOCAL
AV?/1
VIDEO 1 VIDEO 2 DVD SA-CD/CD
2CH A.F.D.
RETURN/EXITTV CH –
PRESET –TV CH +
PRESET +
TUNING –
TV
TUNING +
REPLAY ADVANCE
MENU
MOVIE MUSIC
MEMORY DVD MENU
CLEAR
TOOLSDISPLAY MUTING
TV VOLMASTER VOL
FM MODE
D.TUNING
DUAL MONO
TUNER AMP MENU
TV ?/1?/1
-
F
G g
f
.
Hm M
X x
< < >
5
D.SKIP>10/
1
3
2wfwg
5
6
7
8
q;9
qs
qd
qf
qg
qj
qk
qh
qlqa
4
w;
wa
ws
wd
Name Function
A AV ?/1 Press to turn on or off the Sony audio/video components that the remote is assigned to operate.If you press ?/1 (B) at the same time, it will turn off the receiver and other components (SYSTEM STANDBY).NoteThe function of the AV ?/1 switch changes automatically each time you press the input buttons (C).
B TV ?/1 Press TV ?/1 and TV (P) at the same time to turn the TV on or off.
?/1 Press to turn the receiver on or off.To turn off all components, press ?/1 and AV ?/1 (A) at the same time (SYSTEM STANDBY).
C Input buttons Press one of the buttons to select the component you want to use. When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components as follows. You can change the button assignments following the steps in “Changing button assignments” .
D AMP MENU Press to display the menu of the receiver. Then, use the control buttons to perform menu operations.
E MOVIE, MUSIC
Press to select sound fields (MOVIE, MUSIC).
Button Assigned Sony component
VIDEO 1 VCR (VTR mode 3)
VIDEO 2 VCR (VTR mode 2)
DVD DVD player
SA-CD/CD Super Audio CD/CD player
TUNER Built-in tuner
8
STR-K700
F DUAL MONO Press to select the language you want during digital broadcast.
G FM MODE Press to select FM monaural or stereo reception.
H D.TUNING Press to enter direct tuning mode.
D.SKIP Press to skip disc of the CD player or DVD player (multi-disc changer only).
I ENTER Press to enter the value after selecting a channel, disc or track using the numeric buttons.
MEMORY Press to store a station.
J DVD MENU Press to display the menu of the DVD player on the TV screen. Then, use the control buttons to perform menu operations.
K TOOLS Press to display options applicable to the entire disc (e.g. disc protection), recorder (e.g. audio settings during recording), or multiple items on a list menu (e.g. erasing multiple titles).
L MUTING Press to mute the sound.
M TV VOL +*/–
Press TV VOL +/– and TV (P) at the same time to adjust the TV volume level.
MASTER VOL +*/–
Press to adjust the volume level of all speakers at the same time.
N MENU Press to display the menus of the VCR, DVD player, or satellite tuner on the TV screen. Then, use the control buttons to perform menu operations.
Name Function
O ./> Press to skips tracks of the CD player, DVD player, or tape deck.
REPLAY /ADVANCE
Press to replay the previous scene or fast forward the current scene of the VCR or DVD player.
m/M Press to search tracks in the forward/backward direction of the DVD player or to fastforward/rewind of the VCR, CD player, or tape deck.
H* Press to start playback of the VCR, CD player, DVD player, or tape deck.
X Press to pause playback or recording of the VCR, CD player, DVD player, or tape deck. (Also starts recording with components in recording standby.)
x Press to stop playback of the VCR, CD player, DVD player, or tape deck.
TV CH +/– Press TV CH +/– and TV (P) at the same time to select preset TV channels.
PRESET +/– Press to select preset stations or preset channels of the VCR or satellite tuner.
TUNING +/– Press to scan a station.
P TV Press TV and the button you want at the same time to activate the buttons with orange printing.
Q RETURN/EXIT O
Press to return to the previous menu or exit the menu while the menu or on-screen guide of the VCR, DVD player, or satellite tuner is displayed on the TV screen.
R Control buttons
After pressing AMP MENU (D), DVD MENU (J), or MENU (N), press the control button V, v, B or b to select the settings. When you press DVD MENU or MENU, press the control button to enter the selection.
Name Function
<
<
9
STR-K700
* The number 5, MASTER VOL +, TV VOL +, and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.
Notes Some functions explained in this section may not
work depending on the model. The above explanation is intended to serve as an
example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.
S DISPLAY Press to select the information displayed on the TV screen of the VCR, satellite tuner, CD player or DVD player.
T -/-- Press -/-- and TV (P) at the same time to select the channel entry mode, either one or two digits of the TV.
>10/x Press to select track numbers over 10 of the VCR, satellite tuner or CD player or to select channel numbers of the Digital CATV terminal.
CLEAR Press to clear a mistake when you press the incorrect numeric buttons or to return tocontinuous playback, etc. of the satellite tuner or DVD player.
U Numeric buttons (number 5*)
Press to preset/tune to preset stations or to select track numbers of the CD player or DVD player or to select channel numbers of the VCR or satellite tuner. Press 0/10 to select track number 10. Press the numeric buttons and TV (P) at the same time to select the TV channels.
V 2CH Press to select 2CH STEREO mode.
W A.F.D. Press to select A.F.D. mode.
X AUTO CAL Press to activate the Auto Calibration function.
Y TV/VIDEO Press TV/VIDEO and TV (P) at the same time to select the input signal (TV input or video input).
SLEEP Press to activate the Sleep Timer function and the duration which the receiver turns off automatically.
Name Function
10
STR-K700
FACTORY PRESET MODEAll preset contents are reset to the default setting.Procedure:
1. While depressing the 2CH and the DISPLAY buttonssimultaneously, press the power ?/1 button to turn on themain power.
2. The message “FACTORY” appears and the present contentsare reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHzSELECTION MODEEither the 9 kHz step or 10 kHz step can be selected for the AMchannel step.Procedure:
1. Set the FUNCTION to AM. Turn off the main power.2. While depressing the DIMMER button, press the power
?/1 button to turn on the main power.3. Either the message “9 k STEP” or “10 kSTEP” appears. Select
the desired step.
FLUORESCENT INDICATOR TUBE TEST MODEAll fluorescent segments are tested. When this test is activated, allsegments turn on at the same time, then each segment turns on oneafter another.Procedure:
1. While depressing the 2CH and the MUSIC buttonssimultaneously, press the power ?/1 button to turn on themain power.
2. All segments turn on.
3. Turn the INPUT SELECTOR dial.
4. Turn the INPUT SELECTOR dial once again.
5. Turn the INPUT SELECTOR dial once again. All segmentsturn off.
6. Every turning of the INPUT SELECTOR dial turns on eachsegment one after another in the same order.
SOUND FIELD CLEAR MODEThe preset sound field is cleared when this mode is activated. Usethis mode before returning the product to clients upon completionof repair.Procedure:
1. While depressing the MUSIC button, press the power ?/1button to turn on the main power.
2. The message “SF. CLR.” appears and initialization isperformed.
SOFTWARE VERSION DISPLAY MODEThe software version is displayed.Procedure:
1. While depressing the A.F.D. and the MOVIE buttonssimultaneously, press the power ?/1 button to turn on themain power.
2. The model name, destination and the software version aredisplayed.
KEY CHECK MODEButton checkProcedure:
1. While depressing the A.F.D. and the DISPLAY buttonssimultaneously, press the power ?/1 button to turn on themain power.“REST 08” appears.
2. Every pressing of any button other than ?/1 counts downthe buttons. The buttons which are already counted once arenot counted again.
3. When all buttons are pressed “REST 00” appears.
CHANGE COMMON MODEThis mode is command mode changed to AV 1 or AV2.Procedure:
1. While depressing the MOVIE button, press the power ?/1button to turn on the main power.
2. Either the message “C.MODE.AV 1” or “C.MODE.AV 2”appears.
SHIPMENT MODEAll preset contents are reset to the default setting.Procedure:
1. While depressing the SLEEP and the MOVIE buttons si-multaneously, press the power ?/1 button to turn on themain power.
2. “CLEARED” appears and switch off the set.
PROTECTORProcedure:
1. While depressing the DIMMER and the MUSIC buttonssimultaneously, press the power ?/1 button to turn on themain power.
2. “PROT. EVER” appears and switch off the set.
DECODE AUTO ALLProcedure:
1. While depressing the SLEEP and the INPUT MODE but-tons simultaneously, press the power ?/1 button to turn onthe main power.
2. “DEC. TEST” appears and switch off the set.
L
SW
C R
SL S SR
SBL SB SBR
LFE SP A SP B SLEEP OPT COAX MULTI CH IN 96/24
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDSD.RANGE EQ STEREO MONO
D D D D
dBkHzmft.MHz
MEMORY
DIRECT
L
SW
R
S
SB
LFE SP A SP B SLEEP OPT COAX MULTI CH IN 96/24
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDSD.RANGE EQ STEREO MONO
D D D D
dBkHzmft.MHz
MEMORY
DIRECT
C
SL SR
SBL SBR
SP A SP B SLEEP OPT COAX MULTI CH IN 96/24
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDSD.RANGE EQ STEREO MONO
D D D D
kHzmft.MHz
MEMORY
DIRECT
SECTION 2TEST MODE
1111
STR-K700
STR-K700
• Waveforms
– DIGITAL Board –
For Schematic Diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics andtantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
• A : B+ Line.• B : B+ Line.• Voltages and waveforms are dc with respect to ground un-
der no-signal (detuned) conditions.No mark : FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).Voltage variations may be noted due to normal productiontolerances.
• Waveforms are taken with a oscilloscope.• Circled numbers refer to waveforms.• Signal path.
F : FMJ : ANALOGc : DIGITAL
For Printed Wiring Boards.Note:• X : parts extracted from the component side.• a : Through hole.• f : internal component.• : Pattern from the side which enables seeing.
• Indication of transistor.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)
Caution:Pattern face side: Parts on the pattern face side seen from(Side A) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Side B) the parts face are indicated.
1 IC1501 9 (MCLK1)
1 V/DIV, 40 ns/DIV72 ns
3.4 Vp-p
2 IC1101 id (X1)
1 V/DIV, 20 ns/DIV41.6 ns
4.2 Vp-p
3 IC1301 ws (XIN)
1 V/DIV, 40 ns/DIV81 ns
4.4 Vp-p
C
B
These are omitted.
E
Q
B
These are omitted.
C E
Note:The components identi-fied by mark 0 or dot-ted line with mark 0 arecritical for safety.Replace only with partnumber specified.
Note:Les composants identifiéspar une marque 0 sont cri-tiques pour la sécurité.Ne les remplacer que par unepiéce por tant le numérospécifié.
SECTION 3DIAGRAMS
• Circuit Boards Location
DIGITAL board
MAIN board
STANDBY boardPOWER board
ADCC board
HEADPHONE board
DISPLAY board
1212
STR-K700
STR-K700
3-1. BLOCK DIAGRAM – MAIN SECTION –
• Signal Path
: FM
: ANALOG
: DIGITAL
• R-CH is omitted due to same as L-CH.
AUDIO IN
AUDIO IN
AUDIO IN
AUDIO IN
PROCESSOR
49LOUT
40SLOUT
33COUT
DATA24
CLK25
21
VOL_
CLK
VOL_
DATA
_LAT
CH SDA
SCL
22
IC1101(2/3)
DVDIN
VIDEO 2IN
J1301
3 5 6 2IC1303(1/2)
DIGITAL AUDIOI/F RECEIVER
IC1301
L
+7V
DISPLAY/POWERSECTION(Page 13)
DIN25
DO35
DI36
CLK38
CE37
ERROR34
XSTATE17
XMODE48
13CK OUT
20XMCK
14BCK
15LRCK
16DATAO
IC1303(2/2)
5 7 3 1
IC2000(1/2) IC2000(2/2)
X130112.288MHz
AUDIO DSP
IC1503SELECTOR
IC1501
KFSI0
SYSCLK
LRCK
BCK
DOUT
22
16
13
14
15
SDI230
LRCK019
HCLK34
HCS36
HACN32
PM113BST56
XRST2
23SDO1
24SDO2
25SDO3
BCKI229
LRCKI228
BCKII17
LRCKII15
IC1502
SRAM
AUDIO CODECIC1452
AD CONVERTERIC1401
MCLKI38
RST37
ML36
MC35
MDI34
MDO33
10VOUT5
BCK40
LRCK41
DATA347
DATA145
DATA246
14VOUT1
12VOUT3
11VOUT4
ANALOG SOUND
SL
ADFL13
LIN16
19
20
21
SL
C
32SWOUT SBL
SLIN
CIN
SWIN
A
98 97 95 96 99 100 94 1
DO DI
CLK CE
ERRO
R
XSTA
TE
CKSE
L1
DATA
092
LRCK
_SW
20
HCLK
4
HCS
5
HACN
7
PM
3
BST
6
XRST
8
GP12
10
PCM
1608
_RST
ADCC
_DSP
_IN
45
ADCC
_ANA
_OGU
E_IN
12
PCM
1608
_ML
13
PCM
1608
_MC
14
PCM
1608
_MDI
15
PCM
1608
_MDO
5 6
29 30
J402
J2000
J400
VIDEO 1
VIDEO 2
SA-CD/CD
DVD
OPTICALIN
IC1353
DIN14
22 21XIN XOUT
93
XMOD
E
CKSEL147
GP968
HD OUT35
HD IN33
2
GP9
18
HD O
UT
19
HD IN
9MCLK1
12MCLK2
X150213.9MHz
14SCK OUT
1LIN
6RST
20BCKO
19LRCKO
18SDI1
24
6
1 5
2
AUDIO GP869
EXLOCK59
GP1237
INL110
TN1TUNER PACK
FM75 Ω
COAXIAL
AM
R-CH
ST-DI
ST-DO
CLK
CE
STEREO
TUNED
MUTING
FM
AM
R CH
L CH
TUNER +10V10V SYSTEM CONTROLLER
SYSTEM CONTROLLER
IC1101(1/3)
DO73
SLATCH74
TUNER-DATA17
T.SERIAL CLK16
STEREO76
TUNED75
MUTE78
COAXIAL
OPTICAL
DIGITAL
ANTENNA
AUTO CAL MIC
D1301
D1113 D1114
D1112
IC400
SDA SCL
EEPROM
IC1131
IC502WOOFER AMP
Q471+3.3V REG
INL44
INL52
26DVDD
S BA Y
INL36
INL28
9
PCM
1608
_RST
3 7
57
1313
STR-K700
STR-K700
3-2. BLOCK DIAGRAM – DISPLAY/POWER SECTION –
• R-CH is omitted due to same as L-CH.• Signal Path
: FM
IN28
12+V OUT2
POWER AMPIC501
POWER AMPIC601
9NF2
LIMITERQ501,502
11-V OUT2
IN2
12+V OUT2
9NF2
11-V OUT2
BOOSTERQ503
BOOSTERQ504 CURRENT
DETECT
Q505,506
AF POWERPROTECT
Q507
LIMITERQ601,602
BOOSTERQ603
BOOSTERQ604 CURRENT
DETECT
Q605,606
IN28
12+V OUT2
POWER AMPIC701
9NF2
LIMITERQ701,702
11-V OUT2
BOOSTERQ703
BOOSTERQ704 CURRENT
DETECT
Q705,706
2+V OUT1
5NF1
LIMITERQ571,572
3-V OUT1
BOOSTERQ754
BOOSTERQ753 CURRENT
DETECT
Q755,756
D883
D529
D729
PROTECTSWITCH
Q881-883
RELAYDRIVE
Q509RY502
RELAYDRIVE
Q508RY501
RELAYDRIVE
Q608RY601
RELAYDRIVE
Q708RY701
L
R
R
L
R-CH
R-CH
R-CH
PHONES
TM600(1/2)
TM601(1/2)
TM601(2/2)
TM600(2/2)
61
PROT
ECTO
R
62
HP R
Y
66
FRON
T RY
68
REAR
RY
67
C/SB
RY
46
VACS
RV102
ENCODER3 1
VOL_
ENC(
B)
65
VOL_
ENC(
A)
64
POW
ER K
EY
56
?/1
S152
77RSTX
48STOP
54SIRCS
63FUSE DETECT
REMOTECONTROLRECEIVER
1
IC102
D910-913
ACIN
T902
RY901
D915D914
RELAYDRIVE
Q901
D920-923
23VCC5
84VCC3
–7VREG
3 2
+7VREG
1 3AUDIO+7V
IC821
IC822
POW
ER R
Y
58
RELAY+B
D804-807
82 83
X0 X1
X110124MHz
F1
F2
L
SLSL
C
A
IN16SBL
J700
FLUORESCENTINDICATOR TUBE
FL101
59
FL_D
ATA
60
FL_C
LK
47
FL_L
AT
7
DIN
8
CLK
9
STB
14 29
SEG1-16
42 31
GRID1-12
F1 F2
FL DRIVEIC100
FUNCTIONKEY
A/D0
38
S100,101,118,119S114-117
FUNCTIONKEY
A/D1
39
SYSTEM CONTROLLERIC1101(3/3)
AF POWERPROTECT
Q607
AF POWERPROTECT
Q707
IC850(1/2)2 1
FRONT
SURROUND
IC850(2/2)5 7
55
HP D
ETEC
TBUFFERIC101
35AVCC
+3.3VREG
3 1
IC1904
AUDIO–7V
+10VREG
3 1TUNER+10V
IC1902
T901
Q911AC DET
1 2
IC1111
D811
R803
+B
–B
–BSWITCH
Q851,852
–20V REGQ801FL101
–20V
+B SWITCH
Q860-862POWER AMP+B
POWER AMP–B
+5VREG
3 1
IC1031
+5V
+2.5VREG
5+2.5V
+3.3VREG
2
4
IC1901
+3.3V
+5VREG
3 1
IC1001AUDIO+5V
SPEAKERSIMPEDANCE USE 6-16Ω
MASTERVOLUME
RV103
ENCODER3 1
I/P_S
EL(B
)
32
I/P_S
EL(A
)
31
INPUTSELECTOR
8
RESET
+3.3V(STBY)
MAINSECTION(Page 12)
CENTER
SUBWOOFER
1414
STR-K700
STR-K700
3-3. PRINTED WIRING BOARD – DIGITAL BOARD (SIDE A) – :Uses unleaded solder.
:Uses unleaded solder.• See page 11 for Circuit Boards Location.
VIDEO 2IN
DVD INCOXIAL
DIGITAL
1
2
35
1
1
4
5
1
5
6
8
1 2
A
B
C
D
E
F
3 4 5 6 7 8 9
D E
STANDBYBOARDCNP801
(Page 24)
G MAINBOARDCNP501
(Page 19)
F
C
MAINBOARDCNP502
(Page 19)
DISPLAYBOARDCNS100
(Page 25)
BMAIN
BOARDCNP503
(Page 19)
AMAIN
BOARDCNP503
(Page 19)
MAINBOARDCN504
(Page 19)TN1
TUNER UNIT
IC1901
IC1904
IC1031 IC1902
IC1353
IC1001
1616
STR-K700
STR-K700
3-5. SCHEMATIC DIAGRAM – DIGITAL BOARD (1/3) – • See page 11 for Waveforms. • See page 27, 28 for IC Block Diagrams.
17
18
18
No mark : FM
X1301
R1574
R151
7
R151
8
R151
9
R152
0
R152
1
R15
22
R152
5
R152
6
R154
6
R154
7
R154
8
R154
9
R155
0
R155
1
R155
2
R155
3
R155
4
R1514
R1508
R1503
R1356
R1358
R1357
R130
7
R130
9
R1303
R1301
R1528
R1527
R1355
C1310
C1304
C1302
C1360
R1556
C1359
C1517
R1313
R1304
R1501
R1502
R1504
R1505
R1506
R1509
R1149
R1044
R1161
R1160
R1121
R1310
R1515
R1318
C1357
R1302
C1356
C1306
TP1003
TP1005
TP1018
C1314
C1315
C1301
C1303
C1305C1362
C1308
C1516
C1518
C1520
C1519
C1510
C1501
C1503
C1506
C1504C1505
C1355
C1511
X1502
JR1502
R1305
R130
6
C1004
C1005
IC1501
JR1511
R1353
IC1353
R1311
TP10
04
R1308
R136
0
FB1302
R1544
C1313 R1316
FB1502
R1315
R1312
R1314
C1312
FB1306
C135
8
C130
9FB1305
FB1501
R1512
C1522
C1521
R1523
R1513
C1523R1198
R1555
TP10
09
TP10
08
TP10
10 TP1012
TP10
15
R1510
C1525
R1534
C1507
R1573
R1531
R1545
C1508
R1543
R1542
R1571
R1572
R1570
R1136
C1515
C151
3
C1514
R1041
R1042
R1140
R1134
R1135
C1353
C1361
R1359
R1150
R1541
C1502
R1511
R1533
R1532
C1509
R1540
R1539
R1538
R1537
R1536
R1535
C1352
J1301
IC1301
D1004
D1003
IC13
03
D1302
D1301
JR10
20
IC1502
IC1503
FB1503
D1112 D1113 D1114
R1363
TP1011
12.288MHz
10k
220
220
220
220
220
220
220
220 22
0
220
220
220
220
22022
0
220
220
10k
100
220
1k
560k
22k
100
100
33k
5.6k
220
220
75
18p
0.01
0.01
47p
100
10006.3V
47010V
100
100
100
100
100
100
100
100
100
100
100
100
100
1M
1M
10k
1p
4.7k
0.01
4716V
XX
XX
XX
0.1
0.1
0.1
0.1
0.10.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.10.1
2225V
0.1
13.9MHz
0
680
22
0.022
0.1
CXD9862R
0UH
100TORX141L
100
XX
100
100
220
100p 100
100
100
10k
0.1
0.1
18p
1k
27p
27p
220
10k
0.110k
220
100
47010V
220
0.1
10k
220
220
0.1
220
220
10k
10k
10k
100
47010V
0.1
0.1
100
100
100
100
100
0.1
0.1
100
100
220
0.1
100
220
220
0.1
220
220
220
220
220
220
0.1
LC89056W-E
1SS367-T3SONY
1SS367-T3SONY
TC7W
U04
F(TE
12R
)
1SS355TE-17
1SS355TE-17
0
IS61LV6416-10TL8-759-714-49
TC7WH157FU (TE12R)
1SS367-T3SONY
1SS367-T3SONY 1SS367-T3
SONY
100
1717
STR-K700
STR-K700
3-6. SCHEMATIC DIAGRAM – DIGITAL BOARD (2/3) –
20
18
16
No mark : FM
C1001C1002
C1460
C1457
C1438
C1428
C1448
R1486
R1446
R1476
R1466
C1487
C1547
C1566C1569 C1567
C1403
C1407
C1491
R1474
TP1
R1403
R1484
R1435 R1464
R1425
R1407
C1422C1462
C1432
C1472C1441C1483
C1454
C1494
C1405
C1408
C1409
R1402
R1401
C1404
C1402
FB1405
C1401
C1568
FB1452
C1450
FB14
53
C1468
R1436
C1458
CNS501
R1475
R1472
R1471
R1493
R1494
R1495
IC1452
IC1401
R1445
R1460
R1492
R1461
R1491
R1470
R1426 C1418
IC1001
C1406
47010V
0.1
1050V
10
1050V
10 50V
1050V
1k
1k
1k
1k
0.0022
0.0022
0.00220.0022 0.0022
10 50V
4.750V
1050V
10k
10k 100
0.1
0.1
470p
470p
0.1
2.2k
1k
0.1
4716V
0.1
0.0022
0.1
10 50V
1k
10 50V
15P
PCM1602APT
PCM1800E/2K
1k10 50V
TA7805S
4.7 50V 0
0 0
0
00
0
000
0
0
0
0
0
0
0
0
0
0
0
0
• See page 28, 29 for IC Block Diagrams.
1818
STR-K700
STR-K700
3-7. SCHEMATIC DIAGRAM – DIGITAL BOARD (3/3) – • See page 11 for Waveform. • See page 27 for IC Block Diagram. • See page 31 for IC Pin Function Description.
Q503 6-702-390-01 IC MN2488-OPY-MKQ504 6-702-391-01 IC MP1620-OPY-MK
4-2. CHASSIS SECTION
Q553 6-702-390-01 IC MN2488-OPY-MK
Q554 6-702-391-01 IC MP1620-OPY-MKQ603 6-702-390-01 IC MN2488-OPY-MKQ604 6-702-391-01 IC MP1620-OPY-MKQ653 6-702-390-01 IC MN2488-OPY-MKQ654 6-702-391-01 IC MP1620-OPY-MK
Q703 6-702-390-01 IC MN2488-OPY-MKQ704 6-702-391-01 IC MP1620-OPY-MKQ753 6-702-390-01 IC MN2488-OPY-MKQ754 6-702-391-01 IC MP1620-OPY-MK
IC1001 8-759-231-53 IC TA7805SIC1031 6-705-464-01 IC BA50BC0TIC1101 6-806-145-01 IC MB90488BPF-G-174E1IC1111 6-702-913-01 IC S-80929CNMC-G8ZT2GIC1131 6-704-004-01 IC BR24L16F-WE2
IC1301 8-759-825-15 IC LC89056W-EIC1303 8-759-242-70 IC TC7WU04FIC1353 6-600-014-01 IC TORX141L (VIDEO 2 IN)IC1401 8-759-560-56 IC PCM1800E/2KIC1452 6-708-784-01 IC PCM1602APT
IC1501 6-707-754-01 IC CXD9862RIC1502 6-704-832-01 IC IS61LV6416-10TLTIC1503 8-759-546-74 IC TC7WH157FU (TE12R)IC1901 6-707-168-01 IC SI-3008KWFEIC1902 8-759-701-59 IC NJM78M09FA
IC1904 6-705-463-01 IC BA33BC0T
< JACK >
J1301 1-794-972-11 JACK, PIN 1P (DVD IN/COAXIAL)
< JUMPER RESISTOR >
JR1020 1-216-864-11 SHORT CHIP 0JR1202 1-216-864-11 SHORT CHIP 0JR1502 1-216-864-11 SHORT CHIP 0JR1511 1-400-862-11 BEAD, FERRITE
< RESISTOR >
R1035 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1039 1-216-833-11 METAL CHIP 10K 5% 1/10WR1041 1-216-809-11 METAL CHIP 100 5% 1/10WR1042 1-216-809-11 METAL CHIP 100 5% 1/10WR1044 1-216-809-11 METAL CHIP 100 5% 1/10W
R1049 1-216-833-11 METAL CHIP 10K 5% 1/10WR1071 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1072 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1073 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1076 1-216-809-11 METAL CHIP 100 5% 1/10W
R1077 1-216-809-11 METAL CHIP 100 5% 1/10WR1078 1-216-809-11 METAL CHIP 100 5% 1/10WR1082 1-216-809-11 METAL CHIP 100 5% 1/10WR1083 1-216-833-11 METAL CHIP 10K 5% 1/10WR1088 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1094 1-216-833-11 METAL CHIP 10K 5% 1/10WR1095 1-216-833-11 METAL CHIP 10K 5% 1/10WR1096 1-216-833-11 METAL CHIP 10K 5% 1/10WR1097 1-216-845-11 METAL CHIP 100K 5% 1/10WR1105 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1106 1-216-809-11 METAL CHIP 100 5% 1/10WR1107 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1108 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1109 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1112 1-216-809-11 METAL CHIP 100 5% 1/10W
R1113 1-216-809-11 METAL CHIP 100 5% 1/10WR1115 1-216-809-11 METAL CHIP 100 5% 1/10WR1117 1-216-821-11 METAL CHIP 1K 5% 1/10WR1118 1-216-821-11 METAL CHIP 1K 5% 1/10WR1119 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1120 1-216-821-11 METAL CHIP 1K 5% 1/10WR1121 1-216-809-11 METAL CHIP 100 5% 1/10WR1122 1-216-809-11 METAL CHIP 100 5% 1/10WR1123 1-216-809-11 METAL CHIP 100 5% 1/10WR1124 1-216-809-11 METAL CHIP 100 5% 1/10W
R1127 1-216-809-11 METAL CHIP 100 5% 1/10WR1128 1-216-809-11 METAL CHIP 100 5% 1/10WR1129 1-216-809-11 METAL CHIP 100 5% 1/10WR1134 1-216-809-11 METAL CHIP 100 5% 1/10WR1135 1-216-809-11 METAL CHIP 100 5% 1/10W
R1136 1-216-809-11 METAL CHIP 100 5% 1/10WR1137 1-216-809-11 METAL CHIP 100 5% 1/10WR1140 1-216-809-11 METAL CHIP 100 5% 1/10WR1142 1-216-809-11 METAL CHIP 100 5% 1/10WR1143 1-216-809-11 METAL CHIP 100 5% 1/10W
R1144 1-216-809-11 METAL CHIP 100 5% 1/10WR1149 1-216-809-11 METAL CHIP 100 5% 1/10WR1150 1-216-809-11 METAL CHIP 100 5% 1/10WR1151 1-216-809-11 METAL CHIP 100 5% 1/10WR1152 1-216-809-11 METAL CHIP 100 5% 1/10W
R1153 1-216-809-11 METAL CHIP 100 5% 1/10WR1154 1-216-809-11 METAL CHIP 100 5% 1/10WR1155 1-216-809-11 METAL CHIP 100 5% 1/10WR1156 1-216-864-11 SHORT CHIP 0R1157 1-216-864-11 SHORT CHIP 0
R1159 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1160 1-216-809-11 METAL CHIP 100 5% 1/10WR1161 1-216-809-11 METAL CHIP 100 5% 1/10WR1162 1-216-809-11 METAL CHIP 100 5% 1/10WR1163 1-216-841-11 METAL CHIP 47K 5% 1/10W
R1164 1-216-864-11 SHORT CHIP 0R1167 1-216-809-11 METAL CHIP 100 5% 1/10WR1168 1-216-809-11 METAL CHIP 100 5% 1/10WR1179 1-216-833-11 METAL CHIP 10K 5% 1/10WR1180 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1186 1-216-833-11 METAL CHIP 10K 5% 1/10WR1187 1-216-833-11 METAL CHIP 10K 5% 1/10WR1189 1-216-833-11 METAL CHIP 10K 5% 1/10WR1190 1-216-833-11 METAL CHIP 10K 5% 1/10WR1191 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1192 1-216-833-11 METAL CHIP 10K 5% 1/10WR1194 1-216-864-11 SHORT CHIP 0R1198 1-216-833-11 METAL CHIP 10K 5% 1/10WR1201 1-216-837-11 METAL CHIP 22K 5% 1/10WR1251 1-216-840-11 METAL CHIP 39K 5% 1/10W
R1252 1-216-840-11 METAL CHIP 39K 5% 1/10WR1260 1-216-821-11 METAL CHIP 1K 5% 1/10WR1261 1-216-821-11 METAL CHIP 1K 5% 1/10WR1301 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR1302 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
DIGITAL
39
STR-K700
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R1303 1-216-839-11 METAL CHIP 33K 5% 1/10WR1304 1-216-809-11 METAL CHIP 100 5% 1/10WR1305 1-216-819-11 METAL CHIP 680 5% 1/10WR1306 1-216-801-11 METAL CHIP 22 5% 1/10WR1307 1-216-809-11 METAL CHIP 100 5% 1/10W
R1308 1-216-809-11 METAL CHIP 100 5% 1/10WR1309 1-216-809-11 METAL CHIP 100 5% 1/10WR1310 1-216-857-11 METAL CHIP 1M 5% 1/10WR1311 1-216-809-11 METAL CHIP 100 5% 1/10WR1312 1-216-809-11 METAL CHIP 100 5% 1/10W
R1313 1-216-809-11 METAL CHIP 100 5% 1/10WR1314 1-216-833-11 METAL CHIP 10K 5% 1/10WR1315 1-216-809-11 METAL CHIP 100 5% 1/10WR1316 1-216-809-11 METAL CHIP 100 5% 1/10WR1318 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1353 1-216-809-11 METAL CHIP 100 5% 1/10WR1355 1-218-285-11 METAL CHIP 75 5% 1/10WR1356 1-216-821-11 METAL CHIP 1K 5% 1/10WR1357 1-216-837-11 METAL CHIP 22K 5% 1/10WR1358 1-216-854-11 METAL CHIP 560K 5% 1/10W
R1359 1-216-809-11 METAL CHIP 100 5% 1/10WR1360 1-216-809-11 METAL CHIP 100 5% 1/10WR1363 1-216-809-11 METAL CHIP 100 5% 1/10WR1401 1-216-821-11 METAL CHIP 1K 5% 1/10WR1402 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1403 1-216-833-11 METAL CHIP 10K 5% 1/10WR1407 1-216-809-11 METAL CHIP 100 5% 1/10WR1425 1-216-864-11 SHORT CHIP 0R1426 1-216-821-11 METAL CHIP 1K 5% 1/10WR1435 1-216-864-11 SHORT CHIP 0
R1436 1-216-821-11 METAL CHIP 1K 5% 1/10WR1445 1-216-864-11 SHORT CHIP 0R1446 1-216-821-11 METAL CHIP 1K 5% 1/10WR1458 1-216-833-11 METAL CHIP 10K 5% 1/10WR1459 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1460 1-216-864-11 SHORT CHIP 0R1461 1-216-864-11 SHORT CHIP 0R1464 1-216-864-11 SHORT CHIP 0R1466 1-216-821-11 METAL CHIP 1K 5% 1/10WR1470 1-216-864-11 SHORT CHIP 0
R1471 1-216-864-11 SHORT CHIP 0R1472 1-216-864-11 SHORT CHIP 0R1474 1-216-833-11 METAL CHIP 10K 5% 1/10WR1475 1-216-864-11 SHORT CHIP 0R1476 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1484 1-216-864-11 SHORT CHIP 0R1486 1-216-821-11 METAL CHIP 1K 5% 1/10WR1491 1-216-864-11 SHORT CHIP 0R1492 1-216-864-11 SHORT CHIP 0R1493 1-216-864-11 SHORT CHIP 0
R1494 1-216-864-11 SHORT CHIP 0R1495 1-216-864-11 SHORT CHIP 0R1501 1-216-809-11 METAL CHIP 100 5% 1/10WR1502 1-216-809-11 METAL CHIP 100 5% 1/10WR1503 1-216-813-11 METAL CHIP 220 5% 1/10W
R1504 1-216-809-11 METAL CHIP 100 5% 1/10WR1505 1-216-809-11 METAL CHIP 100 5% 1/10WR1506 1-216-809-11 METAL CHIP 100 5% 1/10W
R1508 1-216-809-11 METAL CHIP 100 5% 1/10WR1509 1-216-809-11 METAL CHIP 100 5% 1/10W
R1510 1-216-809-11 METAL CHIP 100 5% 1/10WR1511 1-216-809-11 METAL CHIP 100 5% 1/10WR1512 1-216-821-11 METAL CHIP 1K 5% 1/10WR1513 1-216-833-11 METAL CHIP 10K 5% 1/10WR1514 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1515 1-216-857-11 METAL CHIP 1M 5% 1/10WR1517 1-216-813-11 METAL CHIP 220 5% 1/10WR1518 1-216-813-11 METAL CHIP 220 5% 1/10WR1519 1-216-813-11 METAL CHIP 220 5% 1/10WR1520 1-216-813-11 METAL CHIP 220 5% 1/10W
R1521 1-216-813-11 METAL CHIP 220 5% 1/10WR1522 1-216-813-11 METAL CHIP 220 5% 1/10WR1523 1-216-813-11 METAL CHIP 220 5% 1/10WR1524 1-216-864-11 SHORT CHIP 0R1525 1-216-813-11 METAL CHIP 220 5% 1/10W
R1526 1-216-813-11 METAL CHIP 220 5% 1/10WR1527 1-216-813-11 METAL CHIP 220 5% 1/10WR1528 1-216-813-11 METAL CHIP 220 5% 1/10WR1531 1-216-813-11 METAL CHIP 220 5% 1/10WR1532 1-216-813-11 METAL CHIP 220 5% 1/10W
R1533 1-216-813-11 METAL CHIP 220 5% 1/10WR1534 1-216-813-11 METAL CHIP 220 5% 1/10WR1535 1-216-813-11 METAL CHIP 220 5% 1/10WR1536 1-216-813-11 METAL CHIP 220 5% 1/10WR1537 1-216-813-11 METAL CHIP 220 5% 1/10W
R1538 1-216-813-11 METAL CHIP 220 5% 1/10WR1539 1-216-813-11 METAL CHIP 220 5% 1/10WR1540 1-216-813-11 METAL CHIP 220 5% 1/10WR1541 1-216-813-11 METAL CHIP 220 5% 1/10WR1542 1-216-813-11 METAL CHIP 220 5% 1/10W
R1543 1-216-813-11 METAL CHIP 220 5% 1/10WR1544 1-216-813-11 METAL CHIP 220 5% 1/10WR1545 1-216-813-11 METAL CHIP 220 5% 1/10WR1546 1-216-813-11 METAL CHIP 220 5% 1/10WR1547 1-216-813-11 METAL CHIP 220 5% 1/10W
R1548 1-216-813-11 METAL CHIP 220 5% 1/10WR1549 1-216-813-11 METAL CHIP 220 5% 1/10WR1550 1-216-813-11 METAL CHIP 220 5% 1/10WR1551 1-216-813-11 METAL CHIP 220 5% 1/10WR1552 1-216-813-11 METAL CHIP 220 5% 1/10W
R1553 1-216-813-11 METAL CHIP 220 5% 1/10WR1554 1-216-813-11 METAL CHIP 220 5% 1/10WR1555 1-216-813-11 METAL CHIP 220 5% 1/10WR1556 1-216-809-11 METAL CHIP 100 5% 1/10WR1570 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1571 1-216-833-11 METAL CHIP 10K 5% 1/10WR1572 1-216-833-11 METAL CHIP 10K 5% 1/10WR1573 1-216-833-11 METAL CHIP 10K 5% 1/10WR1574 1-216-833-11 METAL CHIP 10K 5% 1/10WR1635 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
IC400 6-707-169-01 IC M61542FPIC501 6-600-450-01 IC STK350-530-EIC502 8-759-167-88 IC NJM4565DIC601 6-600-450-01 IC STK350-530-EIC701 6-600-450-01 IC STK350-530-E
IC821 8-759-071-48 IC TA7807SIC822 8-759-071-47 IC TA79007SIC850 8-759-167-88 IC NJM4565D
Q504 6-702-391-01 IC MP1620-OPY-MKQ553 6-702-390-01 IC MN2488-OPY-MKQ554 6-702-391-01 IC MP1620-OPY-MKQ603 6-702-390-01 IC MN2488-OPY-MKQ604 6-702-391-01 IC MP1620-OPY-MK
Q653 6-702-390-01 IC MN2488-OPY-MKQ654 6-702-391-01 IC MP1620-OPY-MKQ703 6-702-390-01 IC MN2488-OPY-MKQ704 6-702-391-01 IC MP1620-OPY-MKQ753 6-702-390-01 IC MN2488-OPY-MK
Q754 6-702-391-01 IC MP1620-OPY-MK0T901 1-443-909-11 POWER TRANSFORMER (MAIN)
TN1 1-693-675-21 TUNER
STR-K700
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.