Top Banner
Tel 208.788.3631 • Toll Free 866.788.3631 • Fax 208.788.1306 • www.sunvalleybronze.com 16-1 PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Revised 02/08/16 Right Hand (RH) Left Hand (LH) OUTSIDE INSIDE Right Hand Reverse (RHR) Left Hand Reverse (LHR) OUTSIDE INSIDE CONTENTS This section contains complete passage latch/mortise bolt privacy sets, trim only passage latch/mortise bolt privacy sets, complete auxiliary mortise bolt sets and trim only auxiliary mortise bolt sets. Complete sets include bronze trim, latches, spindle, fasteners and installation instructions. All complete set part numbers begin with CS. Trim only sets include bronze trim, spindle, fasteners and installation instructions. No latches are included. All trim only passage latch/mortise bolt privacy set part numbers begin with TS. Passage latch/mortise bolt privacy trim sets can be machined to be compatible with most high quality tubular latches. The latch manufacturer, model number and function must be specified when ordering trim only sets. Note: Escutcheon plates under 2 1/4” wide will not cover a 2 1/8” bore. Hand Peened and Inlay orders do NOT qualify for return and are non-refundable. Sun Valley Bronze does not warranty tubular latch set doors 1 7/8” and thicker. TABLE OF CONTENTS: Emergency Release Keys Page 16-2 Privacy Indicator Bolts Page 16-3 Auxiliary Mortise Bolt Sets Pages 16-4 – 16-30 Bevel Edge Passage Latch/Mortise Bolt Privacy Sets Pages 16-31 – 16-39 Arch Passage Latch/Mortise Bolt Privacy Sets Pages 16-40 – 16-48 Oval Series Passage Latch/Mortise Bolt Privacy Sets Page 16-49 Contemporary Passage Latch/Mortise Bolt Privacy Sets Pages 16-50 – 16-60 Fleur de Lis Passage Latch/Mortise Bolt Privacy Sets Pages 16-61 – 16-63 Ridge Passage Latch/Mortise Bolt Privacy Sets Pages 16-64 – 16-71 Corrugated w/Band Passage Latch/Mortise Bolt Privacy Sets Pages 16-72 – 16-73 Hampton Passage Latch/Mortise Bolt Privacy Sets Pages 16-74 – 16-76 Trellis Passage Latch/Mortise Bolt Privacy Sets Pages 16-77 – 16-79 Deco Passage Latch/Mortise Bolt Privacy Sets Pages 16-80 – 16-81 Corrugated Passage Latch/Mortise Bolt Privacy Sets Pages 16-82 – 16-84 Bandbox Passage Latch/Mortise Bolt Privacy Sets Pages 16-85 – 16-89 Hand Peened Passage Latch/Mortise Bolt Privacy Sets Pages 16-90 – 16-94 Horizontal Inlay Passage Latch/Mortise Bolt Privacy Sets Page 16-95 Vertical Inlay Passage Latch/Mortise Bolt Privacy Sets Page 16-96 Circles Passage Latch/Mortise Bolt Privacy Sets Page 16-97 Squares Passage Latch/Mortise Bolt Privacy Sets Page 16-98 Corduroy Passage Latch/Mortise Bolt Privacy Sets Pages 16-99 – 16-103 Mesa Passage Latch/Mortise Bolt Privacy Sets Pages 16-104 – 16-109 Burlap Passage Latch/Mortise Bolt Privacy Sets Pages 16-110 – 16-112 Novus Passage Latch/Mortise Bolt Privacy Sets Pages 16-113 – 16-122 Ridge Burlap Passage Latch/Mortise Bolt Privacy Sets Pages 16-123 – 16-125 ORDERING INSTRUCTIONS: Complete Sets and Trim Sets: See Ordering Instructions in Binder 1/ Dealer Information. Custom Sets: See Custom Ordering Instructions in Binder 1/ Dealer Information. DOOR HANDING GUIDE:
125

Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Jul 25, 2016

Download

Documents

 
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m16-1

PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Revised 02/08/16

Right Hand (RH)Left Hand (LH)OUTSIDE

INSIDE

Right Hand Reverse (RHR)Left Hand Reverse (LHR)OUTSIDE

INSIDE

CONTENTSThis section contains complete passage latch/mortise bolt privacy sets, trim only passage latch/mortise bolt privacy sets, complete auxiliary mortise bolt sets and trim only auxiliary mortise bolt sets. Complete sets include bronze trim, latches, spindle, fasteners and installation instructions. All complete set part numbers begin with CS. Trim only sets include bronze trim, spindle, fasteners and installation instructions. No latches are included. All trim only passage latch/mortise bolt privacy set part numbers begin with TS. Passage latch/mortise bolt privacy trim sets can be machined to be compatible with most high quality tubular latches. The latch manufacturer, model number and function must be specified when ordering trim only sets. Note: Escutcheon plates under 2 1/4” wide will not cover a 2 1/8” bore.Hand Peened and Inlay orders do NOT qualify for return and are non-refundable.Sun Valley Bronze does not warranty tubular latch set doors 1 7/8” and thicker.

TABLE OF CONTENTS:Emergency Release Keys Page 16-2Privacy Indicator Bolts Page 16-3Auxiliary Mortise Bolt Sets Pages 16-4 – 16-30 Bevel Edge Passage Latch/Mortise Bolt Privacy Sets Pages 16-31 – 16-39Arch Passage Latch/Mortise Bolt Privacy Sets Pages 16-40 – 16-48Oval Series Passage Latch/Mortise Bolt Privacy Sets Page 16-49Contemporary Passage Latch/Mortise Bolt Privacy Sets Pages 16-50 – 16-60Fleur de Lis Passage Latch/Mortise Bolt Privacy Sets Pages 16-61 – 16-63Ridge Passage Latch/Mortise Bolt Privacy Sets Pages 16-64 – 16-71Corrugated w/Band Passage Latch/Mortise Bolt Privacy Sets Pages 16-72 – 16-73Hampton Passage Latch/Mortise Bolt Privacy Sets Pages 16-74 – 16-76Trellis Passage Latch/Mortise Bolt Privacy Sets Pages 16-77 – 16-79Deco Passage Latch/Mortise Bolt Privacy Sets Pages 16-80 – 16-81Corrugated Passage Latch/Mortise Bolt Privacy Sets Pages 16-82 – 16-84Bandbox Passage Latch/Mortise Bolt Privacy Sets Pages 16-85 – 16-89Hand Peened Passage Latch/Mortise Bolt Privacy Sets Pages 16-90 – 16-94Horizontal Inlay Passage Latch/Mortise Bolt Privacy Sets Page 16-95Vertical Inlay Passage Latch/Mortise Bolt Privacy Sets Page 16-96Circles Passage Latch/Mortise Bolt Privacy Sets Page 16-97Squares Passage Latch/Mortise Bolt Privacy Sets Page 16-98Corduroy Passage Latch/Mortise Bolt Privacy Sets Pages 16-99 – 16-103Mesa Passage Latch/Mortise Bolt Privacy Sets Pages 16-104 – 16-109Burlap Passage Latch/Mortise Bolt Privacy Sets Pages 16-110 – 16-112Novus Passage Latch/Mortise Bolt Privacy Sets Pages 16-113 – 16-122Ridge Burlap Passage Latch/Mortise Bolt Privacy Sets Pages 16-123 – 16-125

ORDERING INSTRUCTIONS:Complete Sets and Trim Sets: See Ordering Instructions in Binder 1/ Dealer Information. Custom Sets: See Custom Ordering Instructions in Binder 1/ Dealer Information. DOOR HANDING GUIDE:

Page 2: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-2

Revised 02/08/16

Illustrations are for demonstration purposes only.

Emergency release keys.

EMERGENCY RELEASE KEYS

ERK-302 – Emergency release key.

1 1/2"

1 1/

4"

ERK-900 – Emergency release key.

1 3/8"

1 1/

4"

ERK-741 – Emergency release key.

1 3/8"

1 3/

8"

ERK-306 – Ridge emergency release key.

1 3/8"

1 5/

16"

ERK-HP306 – Hand Peened emergency

release key.

1 3/8"

1 5/

16"

1"

ERK-326 – Emergency release key.

15/16"

1 1/

2"

ERK-761 – Emergency release key.

1 3/8"1

3/8"

ERK-767 – Emergency release key.

1 3/8"

13/1

6"

ERK-W1600 – Inlay emergency

release key.

1 3/8"

1 1/

4"

3/8"

ERK-W1601 – Inlay emergency

release key.

1 3/8"

1 3/

8"

3/16"

3/8"

3/16"

ERK-302 1 1/2” x 1 1/4” Emergency release key.

ERK-306 1 3/8” x 1 5/16” Ridge emergency release key.

ERK-HP306 1 3/8” x 1 5/16” Hand Peened Emergency release key.

ERK-326 1 5/16” x 1 1/2” Emergency release key.

ERK-741 1 3/8” x 1 3/8” Emergency release key.

ERK-761 1 3/8” x 1 3/8” Emergency release key.

ERK-767 1 3/8” x 13/16” Emergency release key.

ERK-900 1 3/8” x 1 1/4” Emergency release key.

ERK-W1600 1 3/8” x 1 1/4” Inlay emergency release key.

ERK-W1601 1 3/8” x 1 3/8” Inlay emergency release key.

Page 3: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-3

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

I-925 - I-926 PRIVACY INDICATOR AUXILIARY MORTISE BOLT SETS

Complete sets with tubular mortise bolt.

Trim sets with tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of mortise bolt to be used.

CS-I-RP926MB – Complete vacant-occupied indicator

set with mortise bolt. OR TS-I-RP926MB – Trim set only. No latch.

2 1/2"

2 1/

2"

2 1/2"2 1/2"

2 1/

2"

2 1/2"

CS-I-926MB – Complete vacant-occupied indicator

set with mortise bolt. OR TS-I-926MB – Trim set only. No latch.

2 1/4"

2 1/

4"

2 1/4"

CS-I-925MB – Complete vacant-occupied indicator

set with mortise bolt. OR TS-I-925MB – Trim set only. No latch.

OCCUPIED OC

CUPIED OCCUPIED

CS-I-925MB 2 1/4” Square privacy indicator bolt. I-925MB (ext) I-925MB-TPC (int)

CS-I-926MB 2 1/2” Square privacy indicator bolt. I-926MB (ext) I-926MB-TPC (int)

CS-I-RP926MB 2 1/2” Round privacy indicator bolt. I-RP926MB (ext) I-RP926MB-TPC (int)

TS-I-925MB 2 1/4” Square privacy indicator bolt. I-925MB (ext) I-925MB-TPC (int)

TS-I-926MB 2 1/2” Square privacy indicator bolt. I-926MB (ext) I-926MB-TPC (int)

TS-I-RP926MB 2 1/2” Round privacy indicator bolt. I-RP926MB (ext) I-RP926MB-TPC (int)

Page 4: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-4

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

157/158 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

CS-157/158MB – Complete set with mortise bolt. OR TS-157/158MB – Trim set only. No latch.

CS-158MB – Complete set with mortise bolt. OR TS-158MB – Trim set only. No latch.

1 5/8"1

5/8"

1 5/8" 1 5/8"

1 5/

8"

CS-158MB/RC-4 – Complete set with mortise bolt. OR TS-158MB/RC-4 – Trim set only. No latch.

3/4" 1 5/8"

1"

CS-157/158MB Privacy bolt. 157MB-ERC (ext) 158MB-TPC (int)

CS-158MB/RC-4 Privacy bolt. RC-4 (ext) 158MB-TPC (int)

CS-158MB Privacy bolt. Interior only. 158MB-TPC (int)

TS-157/158MB Privacy bolt. 157MB-ERC (ext) 158MB-TPC (int)

TS-158MB/RC-4 Privacy bolt. RC-4 (ext) 158MB-TPC (int)

TS-158MB Privacy bolt. Interior only. 158MB-TPC (int)

Page 5: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-5

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

174/175 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

CS-174/175MB – Complete set with mortise bolt. OR TS-174/175MB – Trim set only. No latch.

CS-175MB – Complete set with mortise bolt. OR TS-175MB – Trim set only. No latch.

1 3/4"1

3/4"

1 3/4" 1 3/4"

1 3/

4"

CS-175MB/RC-4 – Complete set with latch and spindle. OR TS-175MB/RC-4 – Trim set only. No latch.

1 3/4"3/4"

1"

CS-174/175MB Privacy bolt. 174MB-ERC (ext) 175MB-TPC (int)

CS-175MB/RC-4 Privacy bolt. RC-4 (ext) 175MB-TPC (int)

CS-175MB Privacy bolt. Interior only. 175MB-TPC (int)

TS-174/175MB Privacy bolt. 174MB-ERC (ext) 175MB-TPC (int)

TS-175MB/RC-4 Privacy bolt. RC-4 (ext) 175MB-TPC (int)

TS-175MB Privacy bolt. Interior only. 175MB-TPC (int)

Page 6: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-6

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options..

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

199/200 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

CS-199/200MB – Complete set with mortise bolt. OR TS-199/200MB – Trim set only. No latch.

CS-200MB – Complete set with mortise bolt. OR TS-200MB – Trim set only. No latch.

2"2"

2" 2"

2"

CS-200MB/RC-4 – Complete set with latch and spindle. OR TS-200MB/RC-4 – Trim set only. No latch.

2"3/4"

1"

CS-199/200MB Privacy bolt. 199MB-ERC (ext) 200MB-TPC (int)

CS-200MB/RC-4 Privacy bolt. RC-4 (ext) 200MB-TPC (int)

CS-200MB Privacy bolt. Interior only. 200MB-TPC (int)

TS-199/200MB Privacy bolt. 199MB-ERC (ext) 200MB-TPC (int)

TS-200MB/RC-4 Privacy bolt. RC-4 (ext) 200MB-TPC (int)

TS-200MB Privacy bolt. Interior only. 200MB-TPC (int)

Page 7: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-7

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

442/443 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-442/443MB – Complete set with mortise bolt. OR TS-442/443MB – Trim set only. No latch.

CS-443MB – Complete set with mortise bolt. OR TS-443MB – Trim set only. No latch.

2 1/4"2

1/4"

2 1/4" 2 1/4"

2 1/

4"

CS-443MB/RC-4 – Complete set with mortise bolt. OR TS-443MB/RC-4 – Trim set only. No latch.

2 1/4"3/4"

1"

CS-442/443MB Privacy bolt. 442MB-ERC (ext) 443MB-TPC (int)

CS-443MB/RC-4 Privacy bolt. RC-4 (ext) 443MB-TPC (int)

CS-443MB Privacy bolt. Interior only. 443MB-TPC (int)

TS-442/443MB Privacy bolt. 442MB-ERC (ext) 443MB-TPC (int)

TS-443MB/RC-4 Privacy bolt. RC-4 (ext) 443MB-TPC (int)

TS-443MB Privacy bolt. Interior only. 443MB-TPC (int)

Page 8: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-8

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

RP157/RP158 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-RP157/RP158MB Privacy bolt. RP-157MB-ERC (ext) RP-158MB-TPC (int)

CS-RP158MB/RC-4 Privacy bolt. RC-4 (ext) RP-158MB-TPC (int)

CS-RP158MB Privacy bolt. Interior only. RP-158MB-TPC (int)

TS-RP157/RP158MB Privacy bolt. RP-157MB-ERC (ext) RP-158MB-TPC (int)

TS-RP158MB/RC-4 Privacy bolt. RC-4 (ext) RP-158MB-TPC (int)

TS-RP158MB Privacy bolt. Interior only. RP-158MB-TPC (int)

CS-RP157/RP158MB – Complete set with mortise bolt. OR TS-RP157/RP158MB – Trim set only. No latch.

CS-RP158MB/RC-4 – Complete set with mortise bolt. OR TS-RP158MB/RC-4 – Trim set only. No latch.

1 5/8"1

5/8"

1 5/8" 1 5/8"

CS-RP158MB – Complete set with mortise bolt. OR TS-RP158MB – Trim set only. No latch.

1 5/8"

1 5/

8"

3/4"

1"

Page 9: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-9

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

RP174/RP175 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-RP174/RP175MB – Complete set with mortise bolt. OR TS-RP174/RP175MB – Trim set only. No latch.

CS-RP175MB/RC-4 – Complete set with mortise bolt. OR TS-RP175MB/RC-4 – Trim set only. No latch.

1 3/4"1

3/4"

1 3/4" 1 3/4"

CS-RP175MB – Complete set with mortise bolt. OR TS-RP175MB – Trim set only. No latch.

1 3/4"

1 3/

4"

3/4"

1"

CS-RP174/RP175MB Privacy bolt. RP-174MB-ERC (ext) RP-175MB-TPC (int)

CS-RP175MB/RC-4 Privacy bolt. RC-4 (ext) R-P175MB-TPC (int)

CS-RP175MB Privacy bolt. Interior only. RP-175MB-TPC (int)

TS-RP174/RP175MB Privacy bolt. RP-174MB-ERC (ext) RP-175MB-TPC (int)

TS-RP175MB/RC-4 Privacy bolt. RC-4 (ext) RP-175MB-TPC (int)

TS-RP175MB Privacy bolt. Interior only. RP-175MB-TPC (int)

Page 10: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-10

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

CS-RP199/RP200MB Privacy bolt. RP-199MB-ERC (ext) RP-200MB-TPC (int)

CS-RP200MB/RC-4 Privacy bolt. RC-4 (ext) RP-200MB-TPC (int)

CS-RP200MB Privacy bolt. Interior only. RP-200MB-TPC (int)

TS-RP199/RP200MB Privacy bolt. RP-199MB-ERC (ext) RP-200MB-TPC (int)

TS-RP200MB/RC-4 Privacy bolt. RC-4 (ext) RP-200MB-TPC (int)

TS-RP200MB Privacy bolt. Interior only. RP-200MB-TPC (int)

RP199/RP200 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

CS-RP199/RP200MB – Complete set with mortise bolt. OR TS-RP199/RP200MB – Trim set only. No latch.

CS-RP200MB/RC-4 – Complete set with mortise bolt. OR TS-RP200MB/RC-4 – Trim set only. No latch.

2"2"

2" 2"

CS-RP200MB – Complete set with mortise bolt. OR TS-RP200MB – Trim set only. No latch.

2"

2"

3/4"

1"

Page 11: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-11

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

440/441 BEVEL EDGE AUXILIARY MORTISE BOLT SETS

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-440/441MB – Complete set with mortise bolt. OR TS-440/441MB – Trim set only. No latch.

CS-441MB – Complete set with mortise bolt. OR TS-441MB – Trim set only. No latch.

2 1/4"2

1/4"

2 1/4" 2 1/4"

2 1/

4"

CS-441MB/RC-4 – Complete set with mortise bolt. OR TS-441MB/RC-4 – Trim set only. No latch.

2 1/4"3/4"

1"

CS-440/441MB Privacy bolt. RP-440MB-ERC (ext) RP-441MB-TPC (int)

CS-441MB/RC-4 Privacy bolt. RC-4 (ext) RP-441MB-TPC (int)

CS-441MB Privacy bolt. Interior only. RP-441MB-TPC (int)

TS-440/441MB Privacy bolt. RP-440MB-ERC (ext) RP-441MB-TPC (int)

TS-441MB/RC-4 Privacy bolt. RC-4 (ext) RP-441MB-TPC (int)

TS-441MB Privacy bolt. Interior only. RP-441MB-TPC (int)

Page 12: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-12

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options..

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

444/445 OVAL AUXILIARY MORTISE BOLT SETS

CS-444/445MB – Complete set with mortise bolt. OR TS-444/445MB – Trim set only. No latch.

CS-445MB – Complete set with mortise bolt. OR TS-445MB – Trim set only. No latch.

1 3/4"3"

1 3/4" 1 3/4"

3"

CS-445MB/RC-4 – Complete set with mortise bolt. OR TS-445MB/RC-4 – Trim set only. No latch.

1 3/4"3/4"

1" 3"

CS-444/445MB Privacy bolt. OP444MB-ERC (ext) OP445MB-TPC (int)

CS-445MB/RC-4 Privacy bolt. RC-4 (ext) OP445MB-TPC (int)

CS-445MB Privacy bolt. Interior only. OP445MB-TPC (int)

TS-444/445MB Privacy bolt. OP444MB-ERC (ext) OP445MB-TPC (int)

TS-445MB/RC-4 Privacy bolt. RC-4 (ext) OP445MB-TPC (int)

TS-445MB Privacy bolt. Interior only. OP445MB-TPC (int)

Page 13: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-13

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

9157/9158 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-9157/9158MB – Complete set with mortise bolt. OR TS-9157/9158MB – Trim set only. No latch.

CS-9158MB – Complete set with mortise bolt. OR TS-9158MB – Trim set only. No latch.

1 5/8"1

5/8"

1 5/8" 1 5/8"

1 5/

8"

CS-9158MB/RC-9 – Complete set with mortise bolt. OR TS-9158MB/RC-9 – Trim set only. No latch.

3/4" 1 5/8"

1"

CS-9157/9158MB Privacy bolt. 9157MB-ERC (ext) 9158MB-TPC (int)

CS-9158MB/RC-9 Privacy bolt. RC-9 (ext) 9158MB-TPC (int)

CS-9158MB Privacy bolt. Interior only. 9158MB-TPC (int)

TS-9157/9158MB Privacy bolt. 9157MB-ERC (ext) 9158MB-TPC (int)

TS-9158MB/RC-9 Privacy bolt. RC-9 (ext) 9158MB-TPC (int)

TS-9158MB Privacy bolt. Interior only. 9158MB-TPC (int)

Page 14: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-14

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-9492/9493MB – Complete set with mortise bolt. OR TS-9492/9493MB – Trim set only. No latch.

CS-9493MB – Complete set with mortise bolt. OR TS-9493MB – Trim set only. No latch.

2 1/4"2

1/4"

2 1/4" 2 1/4"

2 1/

4"

CS-9493MB/RC-9 – Complete set with mortise bolt. OR TS-9493MB/RC-9 – Trim set only. No latch.

2 1/

4"

2 1/4"3/4"

1"

CS-9492/9493MB Privacy bolt. 9492MB-ERC (ext) 9493MB-TPC (int)

CS-9493MB/RC-9 Privacy bolt. RC-9 (ext) 9493MB-TPC (int)

CS-9493MB Privacy bolt. Interior only. 9493MB-TPC (int)

TS-9492/9493MB Privacy bolt. 9492MB-ERC (ext) 9493MB-TPC (int)

TS-9493MB/RC-9 Privacy bolt. RC-9 (ext) 9493MB-TPC (int)

TS-9493MB Privacy bolt. Interior only. 9493MB-TPC (int)

9492/9493 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

Page 15: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-15

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

9494/9495 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

CS-9494/9495MB – Complete set with mortise bolt. OR TS-9494/9495MB – Trim set only. No latch.

CS-9495MB – Complete set with mortise bolt. OR TS-9495MB – Trim set only. No latch.

2"

2"

2" 2"

2"

CS-9495MB/RC-9 – Complete set with mortise bolt. OR TS-9495MB/RC-9 – Trim set only. No latch.

2"

2"3/4"

1"

CS-9494/9495MB Privacy bolt. 9494MB-ERC (ext) 9495MB-TPC (int)

CS-9495MB/RC-9 Privacy bolt. RC-9 (ext) 9495MB-TPC (int)

CS-9495MB Privacy bolt. Interior only. 9495MB-TPC (int)

TS-9494/9495MB Privacy bolt. 9494MB-ERC (ext) 9495MB-TPC (int)

TS-9495MB/RC-9 Privacy bolt. RC-9 (ext) 9495MB-TPC (int)

TS-9495MB Privacy bolt. Interior only. 9495MB-TPC (int)

Page 16: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-16

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

9496/9497 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

CS-9496/9497MB – Complete set with mortise bolt. OR TS-9496/9497MB – Trim set only. No latch.

CS-9497MB – Complete set with mortise bolt. OR TS-9497MB – Trim set only. No latch.

1 3/4"

1 3/

4"

1 3/4" 1 3/4"

1 3/

4"

3/4"

1"

CS-9497MB/RC-9 – Complete set with mortise bolt. OR TS-9497MB/RC-9 – Trim set only. No latch.

1 3/

4"

1 3/4"

CS-9496/9497MB Privacy bolt. 9496MB-ERC (ext) 9497MB-TPC (int)

CS-9497MB/RC-9 Privacy bolt. RC-9 (ext) 9497MB-TPC (int)

CS-9497MB Privacy bolt. Interior only. 9497MB-TPC (int)

TS-9496/9497MB Privacy bolt. 9496MB-ERC (ext) 9497MB-TPC (int)

TS-9497MB/RC-9 Privacy bolt. RC-9 (ext) 9497MB-TPC (int)

TS-9497MB Privacy bolt. Interior only. 9497MB-TPC (int)

Page 17: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-17

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

RP9157/RP9158 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

CS-RP9157/RP9158MB – Complete set with mortise bolt. OR TS-RP9157/RP9158MB – Trim set only. No latch.

CS-RP9158MB/RC-9 – Complete set with mortise bolt. OR TS-RP9158MB/RC-9 – Trim set only. No latch.

1 5/8"

1 5/

8"

1 5/8" 1 5/8"

1 5/

8"

CS-RP9158MB – Complete set with mortise bolt. OR TS-RP9158MB – Trim set only. No latch.

1 5/8"

1 5/

8"

3/4"

1"

CS-RP9157/RP9158MB Privacy bolt. RP-9157MB-ERC (ext) RP-9158MB-TPC (int)

CS-RP9158MB/RC-9 Privacy bolt. RC-9 (ext) RP-9158MB-TPC (int)

CS-RP9158MB Privacy bolt. Interior only. RP-9158MB-TPC (int)

TS-RP9157/RP9158MB Privacy bolt. RP-9157MB-ERC (ext) RP-9158MB-TPC (int)

TS-RP9158MB/RC-9 Privacy bolt. RC-9 (ext) RP-9158MB-TPC (int)

TS-RP9158MB Privacy bolt. Interior only. RP-9158MB-TPC (int)

Page 18: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-18

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

RP9490/RP9491 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

CS-RP9490/RP9491MB – Complete set with mortise bolt. OR TS-RP9490/RP9491MB – Trim set only. No latch.

CS-RP9491MB – Complete set with mortise bolt. OR TS-RP9491MB – Trim set only. No latch.

2 1/4"

2 1/

4"

2 1/4" 2 1/4"

2 1/

4"

CS-RP9491MB/RC-9 – Complete set with mortise bolt. OR TS-RP9491MB/RC-9 – Trim set only. No latch.

2 1/

4"

2 1/4"3/4"

1"

CS-RP9490/RP9491MB Privacy bolt. RP-9490MB-ERC (ext) RP-9491MB-TPC (int)

CS-RP9491MB/RC-9 Privacy bolt. RC-9 (ext) RP-9491MB-TPC (int)

CS-RP9491MB Privacy bolt. Interior only. RP-9491MB-TPC (int)

TS-RP9490/RP9491MB Privacy bolt. RP-9490MB-ERC (ext) RP-9491MB-TPC (int)

TS-RP9491MB/RC-9 Privacy bolt. RC-9 (ext) RP-9491MB-TPC (int)

TS-RP9491MB Privacy bolt. Interior only. RP-9491MB-TPC (int)

Page 19: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-19

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

RP9494/RP9495 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-RP9494/RP9495MB – Complete set with mortise bolt. OR TS-RP9494/RP9495MB – Trim set only. No latch.

CS-RP9495MB – Complete set with mortise bolt. OR TS-RP9495MB – Trim set only. No latch.

2"2"

2" 2"

2"

3/4"

1"

CS-RP9495MB/RC-9 – Complete set with mortise bolt. OR TS-RP9495MB/RC-9 – Trim set only. No latch.

2"

2"

CS-RP9494/RP9495MB Privacy bolt. RP-9494MB-ERC (ext) RP-9495MB-TPC (int)

CS-RP9495MB/RC-9 Privacy bolt. RC-9 (ext) RP-9495MB-TPC (int)

CS-RP9495MB Privacy bolt. Interior only. RP-9495MB-TPC (int)

TS-RP9494/RP9495MB Privacy bolt. RP-9494MB-ERC (ext) RP-9495MB-TPC (int)

TS-RP9495MB/RC-9 Privacy bolt. RC-9 (ext) RP-9495MB-TPC (int)

TS-RP9495MB Privacy bolt. Interior only. RP-9495MB-TPC (int)

Page 20: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-20

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

RP9498/RP9499 CONTEMPORARY AUXILIARY MORTISE BOLT SETS

CS-RP9498/RP9499MB – Complete set with mortise bolt. OR TS-RP9498/RP9499MB – Trim set only. No latch.

CS-RP9499MB – Complete set with mortise bolt. OR TS-RP9499MB – Trim set only. No latch.

1 3/4"

1 3/

4"

1 3/4" 1 3/4"

1 3/

4"

CS-RP9499MB/RC-9 – Complete set with mortise bolt. OR TS-RP9499MB/RC-9 – Trim set only. No latch.

1 3/

4"

1 3/4"3/4"

1"

CS-RP9498/RP9499MB Privacy bolt. RP-9498MB-ERC (ext) RP-9499MB-TPC (int)

CS-RP9499MB/RC-9 Privacy bolt. RC-9 (ext) RP-9499MB-TPC (int)

CS-RP9499MB Privacy bolt. Interior only. RP-9499MB-TPC (int)

TS-RP9498/RP9499MB Privacy bolt. RP-9498MB-ERC (ext) RP-9499MB-TPC (int)

TS-RP9499MB/RC-9 Privacy bolt. RC-9 (ext) RP-9499MB-TPC (int)

TS-RP9499MB Privacy bolt. Interior only. RP-9499MB-TPC (int)

Page 21: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-21

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

19157/19158 CORDUROY AUXILIARY MORTISE BOLT SETS

CS-19157/19158MB – Complete set with mortise bolt. OR TS-19157/19158MB – Trim set only. No latch.

CS-19158MB – Complete set with mortise bolt. OR TS-19158MB – Trim set only. No latch.

1 5/8"1

5/8"

1 5/8" 1 5/8"

1 5/

8"

CS-19158MB/RC-7 – Complete set with mortise bolt. OR TS-19158MB/RC-7 – Trim set only. No latch.

3/4" 1 5/8"

1"

Trim sets for tubular mortise bolt. No mortise bolt included.

Complete sets with tubular mortise bolt.

Specify manufacturer of mortise bolt to be used.

2 3/8” or 2 3/4” backset standard. Please specify.

CS-19157/19158MB Privacy bolt. 19157MB-ERC (ext) 19158MB-TPC (int)

CS-19158MB/RC-7 Privacy bolt. RC-7 (ext) 19158MB-TPC (int)

CS-19158MB Privacy bolt. Interior only. 19158MB-TPC (int)

TS-19157/19158MB Privacy bolt. 19157MB-ERC (ext) 19158MB-TPC (int)

TS-19158MB/RC-7 Privacy bolt. RC-7 (ext) 19158MB-TPC (int)

TS-19158MB Privacy bolt. Interior only. 19158MB-TPC (int)

Page 22: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-22

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Specify manufacturer of mortise bolt to be used.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Complete sets with tubular mortise bolt.

21157/21158 MESA AUXILIARY MORTISE BOLT SETS

CS-21157/21158MB – Complete set with mortise bolt. OR TS-21157/21158MB – Trim set only. No latch.

CS-21158MB – Complete set with mortise bolt. OR TS-21158MB – Trim set only. No latch.

1 5/8"

1 5/

8"

1 5/8"

CS-21158MB/RC-7 – Complete set with mortise bolt. OR TS-21158MB/RC-7 – Trim set only. No latch.

1 5/

8"

1 5/8"

1 5/

8"

1 5/8"3/4"

1"

CS-21157/21158MB Privacy bolt. 21157MB-ERC (ext) 21158MB-TPC (int)

CS-21158MB/RC-7 Privacy bolt. RC-7 (ext) 21158MB-TPC (int)

CS-21158MB Privacy bolt. Interior only. 21158MB-TPC (int)

TS-21157/21158MB Privacy bolt. 21157MB-ERC (ext) 21158MB-TPC (int)

TS-21158MB/RC-7 Privacy bolt. RC-7 (ext) 21158MB-TPC (int)

TS-21158MB Privacy bolt. Interior only. 21158MB-TPC (int)

Page 23: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-23

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular mortise bolt.

2 3/8” or 2 3/4” backset standard. Please specify.

Trim sets for tubular mortise bolt. No mortise bolt included.

Specify manufacturer of mortise bolt to be used.

21199/21200 MESA AUXILIARY MORTISE BOLT SETS

CS-21199/21200MB – Complete set with mortise bolt. OR TS-21199/21200MB – Trim set only. No latch.

CS-21200MB – Complete set with mortise bolt. OR TS-21200MB – Trim set only. No latch.

2"

2"

2" 2"

2"

CS-21200MB/RC-7 – Complete set with mortise bolt. OR TS-21200MB/RC-7 – Trim set only. No latch.

2"

2"3/4"

1"

TS-21199/21200MB Privacy bolt. 21199MB-ERC (ext) 21200MB-TPC (int)

TS-21200MB/RC-7 Privacy bolt. RC-7 (ext) 21200MB-TPC (int)

TS-21200MB Privacy bolt. Interior only. 21200MB-TPC (int)

CS-21199/21200MB Privacy bolt. 21199MB-ERC (ext) 21200MB-TPC (int)

CS-21200MB/RC-7 Privacy bolt. RC-7 (ext) 21200MB-TPC (int)

CS-21200MB Privacy bolt. Interior only. 21200MB-TPC (int)

Page 24: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-24

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

RP21157/RP21158 MESA AUXILIARY MORTISE BOLT SETS

CS-RP21157/RP21158MB – Complete set with mortise bolt. OR TS-RP21157/21158MB – Trim set only. No latch.

CS-RP21158MB – Complete set with mortise bolt. OR TS-RP21158MB – Trim set only. No latch.

1 5/8"1

5/8"

1 5/8" 1 5/8"

1 5/

8"

3/4"

1"

1 5/8"

1 5/

8"

CS-RP21158MB/RC-9 – Complete set with mortise bolt. OR TS-RP21158MB/RC-9 – Trim set only. No latch.

CS-RP21157/RP21158MB Privacy bolt. RP-21157MB-ERC (ext) RP-21158MB-TPC (int)

CS-RP21158MB/RC-9 Privacy bolt. RC-9 (ext) RP-21158MB-TPC (int)

CS-RP21158MB Privacy bolt. Interior only. RP-21158MB-TPC (int)

TS-RP21157/RP21158MB Privacy bolt. RP-21157MB-ERC (ext) RP-21158MB-TPC (int)

TS-RP21158MB/RC-9 Privacy bolt. RC-9 (ext) RP-21158MB-TPC (int)

TS-RP21158MB Privacy bolt. Interior only. RP-21158MB-TPC (int)

Page 25: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-25

Revised 02/08/16

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

RP21199/RP21200 MESA AUXILIARY MORTISE BOLT SETS

CS-RP21199/RP21200MB – Complete set with mortise bolt. OR TS-RP21199/21200MB – Trim set only. No latch.

CS-RP21200MB – Complete set with mortise bolt. OR TS-RP21200MB – Trim set only. No latch.

2"

2"

2" 2"

2"

3/4"

1"

2"

2"

CS-RP21200MB/RC-9 – Complete set with mortise bolt. OR TS-RP21200MB/RC-9 – Trim set only. No latch.

CS-RP21199/RP21200MB Privacy bolt. RP-21199MB-ERC (ext) RP-21200MB-TPC (int)

CS-RP21200MB/RC-9 Privacy bolt. RC-9 (ext) RP-21200MB-TPC (int)

CS-RP21200MB Privacy bolt. Interior only. RP-21200MB-TPC (int)

TS-RP21199/RP21200MB Privacy bolt. RP-21199MB-ERC (ext) RP-21200MB-TPC (int)

TS-RP21200MB/RC-9 Privacy bolt. RC-9 (ext) RP-21200MB-TPC (int)

TS-RP21200MB Privacy bolt. Interior only. RP-21200MB-TPC (int)

Page 26: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-26

Revised 02/08/16

22157/22158 BURLAP AUXILIARY MORTISE BOLT SETS

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

CS-22157/22158MB Privacy bolt. 22157MB-ERC (ext) 22158MB-TPC (int)

CS-22158MB/RC-7 Privacy bolt. RC-7 (ext) 22158MB-TPC (int)

CS-22158MB Privacy bolt. Interior only. 22158MB-TPC (int)

TS-22157/22158MB Privacy bolt. 22157MB-ERC (ext) 22158MB-TPC (int)

TS-22158MB/RC-7 Privacy bolt. RC-7 (ext) 22158MB-TPC (int)

TS-22158MB Privacy bolt. Interior only. 22158MB-TPC (int)

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

CS-22157/22158MB – Complete set with mortise bolt. OR TS-22157/22158MB – Trim set only. No latch.

CS-22158MB – Complete set with mortise bolt. OR TS-22158MB – Trim set only. No latch.

1 5/8"

1 5/

8"

1 5/8"

CS-22158MB/RC-7 – Complete set with mortise bolt. OR TS-22158MB/RC-7 – Trim set only. No latch.

1 5/

8"

1 5/8"

1 5/

8"

1 5/8"3/4"

1"

Page 27: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-27

Revised 02/08/16

22199/22200 BURLAP AUXILIARY MORTISE BOLT SETS

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

CS-22199/22200MB Privacy bolt. 22199MB-ERC (ext) 22200MB-TPC (int)

CS-22200MB/RC-7 Privacy bolt. RC-7 (ext) 22200MB-TPC (int)

CS-22200MB Privacy bolt. Interior only. 22200MB-TPC (int)

TS-22199/22200MB Privacy bolt. 22199MB-ERC (ext) 22200MB-TPC (int)

TS-22200MB/RC-7 Privacy bolt. RC-7 (ext) 22200MB-TPC (int)

TS-22200MB Privacy bolt. Interior only. 22200MB-TPC (int)

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

CS-22199/22200MB – Complete set with mortise bolt. OR TS-22199/22200MB – Trim set only. No latch.

CS-22200MB – Complete set with mortise bolt. OR TS-22200MB – Trim set only. No latch.

2"

2"

2" 2"

2"

CS-22200MB/RC-7 – Complete set with mortise bolt. OR TS-22200MB/RC-7 – Trim set only. No latch.

2"

2"3/4"

1"

Page 28: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-28

Revised 02/08/16

RP22157/RP22158 BURLAP AUXILIARY MORTISE BOLT SETS

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

CS-RP22157/RP22158MB Privacy bolt. RP-22157MB-ERC (ext) RP-22158MB-TPC (int)

CS-RP22158MB/RC-9 Privacy bolt. RC-9 (ext) RP-22158MB-TPC (int)

CS-RP22158MB Privacy bolt. Interior only. RP-22158MB-TPC (int)

TS-RP22157/RP22158MB Privacy bolt. RP-22157MB-ERC (ext) RP-22158MB-TPC (int)

TS-RP22158MB/RC-9 Privacy bolt. RC-9 (ext) RP-22158MB-TPC (int)

TS-RP22158MB Privacy bolt. Interior only. RP-22158MB-TPC (int)

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

CS-RP22157/RP22158MB – Complete set with mortise bolt. OR TS-RP22157/22158MB – Trim set only. No latch.

CS-RP22158MB – Complete set with mortise bolt. OR TS-RP22158MB – Trim set only. No latch.

1 5/8"1

5/8"

1 5/8" 1 5/8"

1 5/

8"

3/4"

1"

1 5/8"

1 5/

8"

CS-RP22158MB/RC-9 – Complete set with mortise bolt. OR TS-RP22158MB/RC-9 – Trim set only. No latch.

Page 29: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-29

Revised 02/08/16

RP22199/RP22200 BURLAP AUXILIARY MORTISE BOLT SETS

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

CS-RP22199/RP22200MB Privacy bolt. RP-22199MB-ERC (ext) RP-22200MB-TPC (int)

CS-RP22200MB/RC-9 Privacy bolt. RC-9 (ext) RP-22200MB-TPC (int)

CS-RP22200MB Privacy bolt. Interior only. RP-22200MB-TPC (int)

TS-RP22199/RP22200MB Privacy bolt. RP-22199MB-ERC (ext) RP-22200MB-TPC (int)

TS-RP22200MB/RC-9 Privacy bolt. RC-9 (ext) RP-22200MB-TPC (int)

TS-RP22200MB Privacy bolt. Interior only. RP-22200MB-TPC (int)

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

CS-RP22199/RP22200MB – Complete set with mortise bolt. OR TS-RP22199/22200MB – Trim set only. No latch.

CS-RP22200MB – Complete set with mortise bolt. OR TS-RP22200MB – Trim set only. No latch.

2"

2"

2" 2"

2"

3/4"

1"

2"

2"

CS-RP22200MB/RC-9 – Complete set with mortise bolt. OR TS-RP22200MB/RC-9 – Trim set only. No latch.

Page 30: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-30

Revised 02/08/16

23157/23158 GEM AUXILIARY MORTISE BOLT SETS

Complete sets with tubular mortise bolt.

Trim sets for tubular mortise bolt. No mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.

Specify manufacturer of latch and mortise bolt to be used.

Illustrations are for demonstration purposes only. Refer to Section 4 for release cover & turn piece options.

CS-23157/23158MB – Complete set with mortise bolt. OR TS-23157/23158MB – Trim set only. No latch.

CS-23158MB – Complete set with mortise bolt. OR TS-23158MB – Trim set only. No latch.

CS-23158MB/RC-9 – Complete set with mortise bolt. OR TS-23158MB/RC-9 – Trim set only. No latch.

3/4"

1"

1 5/8"

1 5/

8"

1 5/8" 1 5/8"

1 5/

8"

1 5/8"

CS-23157/23158MB Privacy bolt. 23157MB-ERC (ext) 23158MB-TPC (int)

CS-23158MB/RC-9 Privacy bolt. RC-9 (ext) 23158MB-TPC (int)

CS-23158MB Privacy bolt. Interior only. 23158MB-TPC (int)

TS-23157/23158MB Privacy bolt. 23157MB-ERC (ext) 23158MB-TPC (int)

TS-23158MB/RC-9 Privacy bolt. RC-9 (ext) 23158MB-TPC (int)

TS-23158MB Privacy bolt. Interior only. 23158MB-TPC (int)

Page 31: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-31

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

405 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-405PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-405PLMB – Trim set only. No latch or mortise bolt.

CS-F405PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F405PLMB – Trim set only. No latch or mortise bolt.

1 3/4"

6 3/

16"

1 3/4" 1 3/4"

6 3/

16"

1 3/4"

2 1/

16"

4 1/

8"2 1/

4"

2 1/

16"

2 1/

4"

2 1/

4"

CS-405PLMB Privacy set. P-405OH-MB-ERC (ext) P-405OH-MB-TPC (int)

CS-F405PLMB Privacy set. P-F405OH-MB-ERC (ext) P-F405OH-MB-TPC (int)

TS-405PLMB Privacy set. P-405OH-MB-ERC (ext) P-405OH-MB-TPC (int)

TS-F405PLMB Privacy set. P-F405OH-MB-ERC (ext) P-F405OH-MB-TPC (int)

Page 32: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-32

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

406 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-406PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-406PLMB – Trim set only. No latch or mortise bolt.

CS-F406PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F406PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6 3/

16"

2 1/2" 2 1/2"

6 3/

16"

2 1/2"

2 1/

8"

2 1/

8"

4 1/

16"

2 1/

4"

2 1/

4"

2 1/

4"

CS-406PLMB Privacy set. P-406OH-MB-ERC (ext) P-406OH-MB-TPC (int)

CS-F406PLMB Privacy set. P-F406OH-MB-ERC (ext) P-F406OH-MB-TPC (int)

TS-406PLMB Privacy set. P-406OH-MB-ERC (ext) P-406OH-MB-TPC (int)

TS-F406PLMB Privacy set. P-F406OH-MB-ERC (ext) P-F406OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 33: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-33

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

407 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-407PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-407PLMB – Trim set only. No latch or mortise bolt.

CS-F407PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F407PLMB – Trim set only. No latch or mortise bolt.

2"

8 3/

4"

2" 2"

8 3/

4"

2"

2 3/

4"

2 3/

4"

6" 3 1/

2"

3 1/

2"

3 1/

2"

CS-407PLMB Privacy set. P-407MB-ERC (ext) P-407MB-TPC (int)

CS-F407PLMB Privacy set. P-F407MB-ERC (ext) P-F407MB-TPC (int)

TS-407PLMB Privacy set. P-407MB-ERC (ext) P-407MB-TPC (int)

TS-F407PLMB Privacy set. P-F407MB-ERC (ext) P-F407MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 34: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-34

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

408 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-408PLMB – Trim set only. No latch or mortise bolt.

CS-F408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F408PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-408PLMB Privacy set. P-408MB-ERC (ext) P-408MB-TPC (int)

CS-F408PLMB Privacy set. P-F408MB-ERC (ext) P-F408MB-TPC (int)

TS-408PLMB Privacy set. P-408MB-ERC (ext) P-408MB-TPC (int)

TS-F408PLMB Privacy set. P-F408MB-ERC (ext) P-F408MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 35: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-35

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

409 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-409PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-409PLMB – Trim set only. No latch or mortise bolt.

CS-F409PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F409PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

2 7/

16"

2 7/

16"

7 9/

16"

4 1/

2"

4 1/

2"

4 1/

2"

CS-409PLMB Privacy set. P-409MB-ERC (ext) P-409MB-TPC (int)

CS-F409PLMB Privacy set. P-F409MB-ERC (ext) P-F409MB-TPC (int)

TS-409PLMB Privacy set. P-409MB-ERC (ext) P-409MB-TPC (int)

TS-F409PLMB Privacy set. P-F409MB-ERC (ext) P-F409MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 36: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-36

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

410 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-410PLMB – Trim set only. No latch or mortise bolt.

CS-F410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F410PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

2 1/

2"

2 1/

2"

7 1/

2" 4 1/

2"

4 1/

2"

4 1/

2"

CS-410PLMB Privacy set. P-410MB-ERC (ext) P-410MB-TPC (int)

CS-F410PLMB Privacy set. P-F410MB-ERC (ext) P-F410MB-TPC (int)

TS-410PLMB Privacy set. P-410MB-ERC (ext) P-410MB-TPC (int)

TS-F410PLMB Privacy set. P-F410MB-ERC (ext) P-F410MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 37: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-37

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

601 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-601PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-601PLMB – Trim set only. No latch or mortise bolt.

CS-F601PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F601PLMB – Trim set only. No latch or mortise bolt.

3"

13"

3" 3"

13"

3"

3" 3"

10"

6"

6"6"

CS-601PLMB Privacy set. P-601MB-ERC (ext) P-601MB-TPC (int)

CS-F601PLMB Privacy set. P-F601MB-ERC (ext) P-F601MB-TPC (int)

TS-601PLMB Privacy set. P-601MB-ERC (ext) P-601MB-TPC (int)

TS-F601PLMB Privacy set. P-F601MB-ERC (ext) P-F601MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 38: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-38

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

602 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-602PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-602PLMB – Trim set only. No latch or mortise bolt.

CS-F602PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F602PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

13"

3 1/2" 3 1/2"

13"

3 1/2"

3" 3"

10"

6"

6"6"

CS-602PLMB Privacy set. P-602MB-ERC (ext) P-602MB-TPC (int)

CS-F602PLMB Privacy set. P-F602MB-ERC (ext) P-F602MB-TPC (int)

TS-602PLMB Privacy set. P-602MB-ERC (ext) P-602MB-TPC (int)

TS-F602PLMB Privacy set. P-F602MB-ERC (ext) P-F602MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 39: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-39

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

811 BEVEL EDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-811PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-811PLMB – Trim set only. No latch or mortise bolt.

CS-F811PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F811PLMB – Trim set only. No latch or mortise bolt.

1 1/2"

10 1

/2"

1 1/2" 1 1/2"

10 1

/2"

1 1/2"

4" 4"

6 1/

2" 3 1/

2"3 1/

2"

3 1/

2"

CS-811PLMB Privacy set. P-811MB-ERC (ext) P-811MB-TPC (int)

CS-F811PLMB Privacy set. P-F811MB-ERC (ext) P-F811MB-TPC (int)

TS-811PLMB Privacy set. P-811MB-ERC (ext) P-811MB-TPC (int)

TS-F811PLMB Privacy set. P-F811MB-ERC (ext) P-F811MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 40: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-40

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

A405 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A405PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A405PLMB – Trim set only. No latch or mortise bolt.

CS-F-A405PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A405PLMB – Trim set only. No latch or mortise bolt.

1 3/4"

7 1/

2"

1 3/4" 1 3/4"

7 1/

2"

1 3/4"

2 1/

4"

2 1/

4" 5 1/

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-A405PLMB Privacy set. P-A405OH-MB-ERC (ext) P-A405OH-MB-TPC (int)

CS-F-A405PLMB Privacy set. P-F-A405OH-MB-ERC (ext) P-F-A405OH-MB-TPC (int)

TS-A405PLMB Privacy set. P-A405OH-MB-ERC (ext) P-A405OH-MB-TPC (int)

TS-F-A405PLMB Privacy set. P-F-A405OH-MB-ERC (ext) P-F-A405OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

Page 41: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-41

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

A406 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A406PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A406PLMB – Trim set only. No latch or mortise bolt.

CS-F-A406PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A406PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

7 1/

2"

2 1/2" 2 1/2"

7 1/

2"

2 1/2"

2 1/

4"

2 1/

4" 5 1/

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-A406PLMB Privacy set. P-A406OH-MB-ERC (ext) P-A406OH-MB-TPC (int)

CS-F-A406PLMB Privacy set. P-F-A406OH-MB-ERC (ext) P-F-A406OH-MB-TPC (int)

TS-A406PLMB Privacy set. P-A406OH-MB-ERC (ext) P-A406OH-MB-TPC (int)

TS-F-A406PLMB Privacy set. P-F-A406OH-MB-ERC (ext) P-F-A406OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 42: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-42

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

A407 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A407PLMB – Complete set with latch and spindle. – Complete set with passage latch, mortise bolt and spindle. OR TS-A407PLMB – Trim set only. No latch or mortise bolt.

CS-F-A407PLMB – Complete set with latch and spindle. – Complete set with passage latch, mortise bolt and spindle. OR TS-F-A407PLMB – Trim set only. No latch or mortise bolt.

2"

8 3/

4"

2" 2"

8 3/

4"

2"

2 3/

4"

2 3/

4"

6" 3 1/

2"

3 1/

2"

3 1/

2"

CS-A407PLMB Privacy set. P-A407MB-ERC (ext) P-A407MB-TPC (int)

CS-F-A407PLMB Privacy set. P-F-A407MB-ERC (ext) P-F-A407MB-TPC (int)

TS-A407PLMB Privacy set. P-A407MB-ERC (ext) P-A407MB-TPC (int)

TS-F-A407PLMB Privacy set. P-F-A407MB-ERC (ext) P-F-A407MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 43: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-43

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

A408 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A408PLMB – Trim set only. No latch or mortise bolt.

CS-F-A408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A408PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

9 1/

4"

2 1/2" 2 1/2"

9 1/

4"

2 1/2"

2 1/

2"

2 1/

2"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-A408PLMB Privacy set. P-A408MB-ERC (ext) P-A408MB-TPC (int)

CS-F-A408PLMB Privacy set. P-F-A408MB-ERC (ext) P-F-A408MB-TPC (int)

TS-A408PLMB Privacy set. P-A408MB-ERC (ext) P-A408MB-TPC (int)

TS-F-A408PLMB Privacy set. P-F-A408MB-ERC (ext) P-F-A408MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 44: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-44

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

A409 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A409PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-A409PLMB – Trim set only. No latch or mortise bolt.

CS-F-A409PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F-A409PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

11"

2 1/2" 2 1/2"

11"

2 1/2"

3" 3"

8"

4 1/

2"

4 1/

2"

4 1/

2"

CS-A409PLMB Privacy set. P-A409MB-ERC (ext) P-A409MB-TPC (int)

CS-F-A409PLMB Privacy set. P-F-A409MB-ERC (ext) P-F-A409MB-TPC (int)

TS-A409PLMB Privacy set. P-A409MB-ERC (ext) P-A409MB-TPC (int)

TS-F-A409PLMB Privacy set. P-F-A409MB-ERC (ext) P-F-A409MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 45: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-45

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

A410 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A410PLMB – Trim set only. No latch or mortise bolt.

CS-F-A410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A410PLMB – Trim set only. No latch or mortise bolt.

3"

11 1

/2"

3" 3"

11 1

/2"

3"

3 1/

8"

3 1/

8"

8 3/

8"4 1/

2"

4 1/

2"

4 1/

2"

CS-A410PLMB Privacy set. P-A410MB-ERC (ext) P-A410MB-TPC (int)

CS-F-A410PLMB Privacy set. P-F-A410MB-ERC (ext) P-F-A410MB-TPC (int)

TS-A410PLMB Privacy set. P-A410MB-ERC (ext) P-A410MB-TPC (int)

TS-F-A410PLMB Privacy set. P-F-A410MB-ERC (ext) P-F-A410MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 46: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-46

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

A601 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A601PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A601PLMB – Trim set only. No latch or mortise bolt.

CS-F-A601PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A601PLMB – Trim set only. No latch or mortise bolt.

3"

14 1

/2"

3" 3"

14 1

/2"

3"

3 3/

4"

3 3/

4"

6"

10 3

/4"6"6"

CS-A601PLMB Privacy set. P-A601MB-ERC (ext) P-A601MB-TPC (int)

CS-F-A601PLMB Privacy set. P-F-A601MB-ERC (ext) P-F-A601MB-TPC (int)

TS-A601PLMB Privacy set. P-A601MB-ERC (ext) P-A601MB-TPC (int)

TS-F-A601PLMB Privacy set. P-F-A601MB-ERC (ext) P-F-A601MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 47: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-47

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

A602 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A602PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A602PLMB – Trim set only. No latch or mortise bolt.

CS-F-A602PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A602PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

15 1

/4"

3 1/2" 3 1/2"

15 1

/4"

3 1/2"

6"

11 1

/2"

3 3/

4"

3 3/

4"

6"6"

CS-A602PLMB Privacy set. P-A602MB-ERC (ext) P-A602MB-TPC (int)

CS-F-A602PLMB Privacy set. P-F-A602MB-ERC (ext) P-F-A602MB-TPC (int)

TS-A602PLMB Privacy set. P-A602MB-ERC (ext) P-A602MB-TPC (int)

TS-F-A602PLMB Privacy set. P-F-A602MB-ERC (ext) P-F-A602MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 48: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-48

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

A811 ARCH PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-A811PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-A811PLMB – Trim set only. No latch or mortise bolt.

CS-F-A811PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-A811PLMB – Trim set only. No latch or mortise bolt.

1 1/2"

10 1

/2"

1 1/2" 1 1/2"

10 1

/2"

1 1/2"

4 1/

4"

4 1/

4"

3 1/

2"

6 1/

4"

3 1/

2"

3 1/

2"

CS-A811PLMB Privacy set. P-A811MB-ERC (ext) P-A811MB-TPC (int)

CS-F-A811PLMB Privacy set. P-F-A811MB-ERC (ext) P-F-A811MB-TPC (int)

TS-A811PLMB Privacy set. P-A811MB-ERC (ext) P-A811MB-TPC (int)

TS-F-A811PLMB Privacy set. P-F-A811MB-ERC (ext) P-F-A811MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 49: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-49

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

OP700 OVAL PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-OP700PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-OP700PLMB – Trim set only. No latch or mortise bolt.

CS-F-OP700PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-OP700PLMB – Trim set only. No latch or mortise bolt.

3"

8 3/

4"

3" 3"

8 3/

4"

3"

2 1/

2"

2 1/

2"

3 1/

2"

6 1/

4"3 1/

2"

3 1/

2"

CS-OP700PLMB Privacy set. P-OP700MB-ERC (ext) P-OP700MB-TPC (int)

CS-F-OP700PLMB Privacy set. P-F-OP700MB-ERC (ext) P-F-OP700MB-TPC (int)

TS-OP700PLMB Privacy set. P-OP700MB-ERC (ext) P-OP700MB-TPC (int)

TS-F-OP700PLMB Privacy set. P-F-OP700MB-ERC (ext) P-F-OP700MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 50: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-50

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

949 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-949PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-949PLMB – Trim set only. No latch or mortise bolt.

CS-F949PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F949PLMB – Trim set only. No latch or mortise bolt.

2"

6"

2" 2"

6"

2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-949PLMB Privacy set. P-949OH-MB-ERC (ext) P-949OH-MB-TPC (int)

CS-F949PLMB Privacy set. P-F949OH-MB-ERC (ext) P-F949OH-MB-TPC (int)

TS-949PLMB Privacy set. P-949OH-MB-ERC (ext) P-949OH-MB-TPC (int)

TS-F949PLMB Privacy set. P-F949OH-MB-ERC (ext) P-F949OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

Page 51: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-51

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

950 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-950PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-950PLMB – Trim set only. No latch or mortise bolt.

CS-F950PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F950PLMB – Trim set only. No latch or mortise bolt.

2"

8 3/

4"

2" 2"

8 3/

4"

2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-950PLMB Privacy set. P-950MB-ERC (ext) P-950MB-TPC (int)

CS-F950PLMB Privacy set. P-F950MB-ERC (ext) P-F950MB-TPC (int)

TS-950PLMB Privacy set. P-950MB-ERC (ext) P-950MB-TPC (int)

TS-F950PLMB Privacy set. P-F950MB-ERC (ext) P-F950MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 52: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-52

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

951 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-951PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-951PLMB – Trim set only. No latch or mortise bolt.

CS-F951PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F951PLMB – Trim set only. No latch or mortise bolt.

2"

10"

2" 2"

10"

2"

2 3/

8"

2 3/

8"

7 5/

8" 4 1/

2"

4 1/

2"

4 1/

2"

CS-951PLMB Privacy set. P-951MB-ERC (ext) P-951MB-TPC (int)

CS-F951PLMB Privacy set. P-F951MB-ERC (ext) P-F951MB-TPC (int)

TS-951PLMB Privacy set. P-951MB-ERC (ext) P-951MB-TPC (int)

TS-F951PLMB Privacy set. P-F951MB-ERC (ext) P-F951MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 53: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-53

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

952 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-952PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-952PLMB – Trim set only. No latch or mortise bolt.

CS-F952PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F952PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

2 1/

4"

2 1/

4"

7 3/

4" 4 1/

2"

4 1/

2"

4 1/

2"

CS-952PLMB Privacy set. P-952MB-ERC (ext) P-952MB-TPC (int)

CS-F952PLMB Privacy set. P-F952MB-ERC (ext) P-F952MB-TPC (int)

TS-952PLMB Privacy set. P-952MB-ERC (ext) P-952MB-TPC (int)

TS-F952PLMB Privacy set. P-F952MB-ERC (ext) P-F952MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 54: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-54

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

953 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-953PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-953PLMB – Trim set only. No latch or mortise bolt.

CS-F953PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F953PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-953PLMB Privacy set. P-953MB-ERC (ext) P-953MB-TPC (int)

CS-F953PLMB Privacy set. P-F953MB-ERC (ext) P-F953MB-TPC (int)

TS-953PLMB Privacy set. P-953MB-ERC (ext) P-953MB-TPC (int)

TS-F953PLMB Privacy set. P-F953MB-ERC (ext) P-F953MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 55: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-55

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

954 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-954PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-954PLMB – Trim set only. No latch or mortise bolt.

CS-F954PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F954PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-954PLMB Privacy set. P-954OH-MB-ERC (ext) P-954OH-MB-TPC (int)

CS-F954PLMB Privacy set. P-F954OH-MB-ERC (ext) P-F954OH-MB-TPC (int)

TS-954PLMB Privacy set. P-954OH-MB-ERC (ext) P-954OH-MB-TPC (int)

TS-F954PLMB Privacy set. P-F954OH-MB-ERC (ext) P-F954OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 56: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-56

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-955PLMB Privacy set. P-955MB-ERC (ext) P-955MB-TPC (int)

CS-F955PLMB Privacy set. P-F955MB-ERC (ext) P-F955MB-TPC (int)

TS-955PLMB Privacy set. P-955MB-ERC (ext) P-955MB-TPC (int)

TS-F955PLMB Privacy set. P-F955MB-ERC (ext) P-F955MB-TPC (int)

955 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-955PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-955PLMB – Trim set only. No latch or mortise bolt.

CS-F955PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F955PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

3 1/

4"

3 1/

4" 6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

Page 57: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-57

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

957 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-957PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-957PLMB – Trim set only. No latch or mortise bolt.

CS-F957PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F957PLMB – Trim set only. No latch or mortise bolt.

3"

12"

3" 3"

12"

3"

3 1/

2"

3 1/

2"

8 1/

2"

4 1/

2"

4 1/

2"

4 1/

2"

CS-957PLMB Privacy set. P-957MB-ERC (ext) P-957MB-TPC (int)

CS-F957PLMB Privacy set. P-F957MB-ERC (ext) P-F957MB-TPC (int)

TS-957PLMB Privacy set. P-957MB-ERC (ext) P-957MB-TPC (int)

TS-F957PLMB Privacy set. P-F957MB-ERC (ext) P-F957MB-TPC (int)

Page 58: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-58

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

959 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

CS-959PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-959PLMB – Trim set only. No latch or mortise bolt.

CS-F959PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F959PLMB – Trim set only. No latch or mortise bolt.

1 3/4"

8 3/

4"

1 3/4" 1 3/4"

8 3/

4"

1 3/4"

2 9/

16"

2 9/

16" 6 3/

16"

3 1/

2"

3 1/

2"

3 1/

2"

CS-959PLMB Privacy set. P-959MB-ERC (ext) P-959MB-TPC (int)

CS-F959PLMB Privacy set. P-F959MB-ERC (ext) P-F959MB-TPC (int)

TS-959PLMB Privacy set. P-959MB-ERC (ext) P-959MB-TPC (int)

TS-F959PLMB Privacy set. P-F959MB-ERC (ext) P-F959MB-TPC (int)

Page 59: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-59

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

979 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-979PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-979PLMB – Trim set only. No latch or mortise bolt.

CS-F979PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F979PLMB – Trim set only. No latch or mortise bolt.

1 1/2"

6"

1 1/2" 1 1/2"

6"

1 1/2"

2"

4" 2 1/

4"

2"2

1/4"

2 1/

4"

CS-979PLMB Privacy set. P-979OH-MB-ERC (ext) P-979OH-MB-TPC (int)

CS-F979PLMB Privacy set. P-F979OH-MB-ERC (ext) P-F979OH-MB-TPC (int)

TS-979PLMB Privacy set. P-979OH-MB-ERC (ext) P-979OH-MB-TPC (int)

TS-F979PLMB Privacy set. P-F979OH-MB-ERC (ext) P-F979OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

Page 60: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-60

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

980 CONTEMPORARY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-980PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-980PLMB – Trim set only. No latch or mortise bolt.

CS-F980PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F980PLMB – Trim set only. No latch or mortise bolt.

1 1/2"

10 1

/2"

1 1/2" 1 1/2"

10 1

/2"

1 1/2"

4" 4"

6 1/

2" 3 1/

2"

3 1/

2"

3 1/

2"

CS-980PLMB Privacy set. P-980MB-ERC (ext) P-980MB-TPC (int)

CS-F980PLMB Privacy set. P-F980MB-ERC (ext) P-F980MB-TPC (int)

TS-980PLMB Privacy set. P-980MB-ERC (ext) P-980MB-TPC (int)

TS-F980PLMB Privacy set. P-F980MB-ERC (ext) P-F980MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 61: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-61

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1240 FLEUR DE LIS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1240PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1240PLMB – Trim set only. No latch or mortise bolt.

CS-F1240PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1240PLMB – Trim set only. No latch or mortise bolt.

1 3/4"

15 5

/8"

1 3/4" 1 3/4"

15 5

/8"

1 3/4"

5 1/

4"

5 1/

4"

10 3

/8"

4 1/

2"

4 1/

2"

4 1/

2"

CS-1240PLMB Privacy set. P-1240MB-ERC (ext) P-1240MB-TPC (int)

CS-F1240PLMB Privacy set. P-F1240MB-ERC (ext) P-F1240MB-TPC (int)

TS-1240PLMB Privacy set. P-1240MB-ERC (ext) P-1240MB-TPC (int)

TS-F1240PLMB Privacy set. P-F1240MB-ERC (ext) P-F1240MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 62: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-62

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1245 FLEUR DE LIS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1245PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1245PLMB – Trim set only. No latch or mortise bolt.

CS-F1245PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1245PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

15 1

/2"

2 1/2" 2 1/2"

15 1

/2"

2 1/2"

5 3/

8"

5 3/

8"

10 1

/8"

4 1/

2"

4 1/

2"

4 1/

2"

CS-1245PLMB Privacy set. P-1245MB-ERC (ext) P-1245MB-TPC (int)

CS-F1245PLMB Privacy set. P-F1245MB-ERC (ext) P-F1245MB-TPC (int)

TS-1245PLMB Privacy set. P-1245MB-ERC (ext) P-1245MB-TPC (int)

TS-F1245PLMB Privacy set. P-F1245MB-ERC (ext) P-F1245MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 63: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-63

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1250 FLEUR DE LIS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1250PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1250PLMB – Trim set only. No latch or mortise bolt.

CS-F1250PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1250PLMB – Trim set only. No latch or mortise bolt.

3"

21 1

/2"

3" 3"

21 1

/2"

3"

7 1/

8"

7 1/

8"

14 3

/8"

6"

6"6"

CS-1250PLMB Privacy set. P-1250MB-ERC (ext) P-1250MB-TPC (int)

CS-F1250PLMB Privacy set. P-F1250MB-ERC (ext) P-F1250MB-TPC (int)

TS-1250PLMB Privacy set. P-1250MB-ERC (ext) P-1250MB-TPC (int)

TS-F1250PLMB Privacy set. P-F1250MB-ERC (ext) P-F1250MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 64: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-64

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

325 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-325PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-325PLMB – Trim set only. No latch or mortise bolt.

CS-F325PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F325PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"2

1/16

"

2 1/

16" 2

1/4"

3 15

/16"

2 1/

4"

2 1/

4"

CS-325PLMB Privacy set. P-325OH-MB-ERC (ext) P-325OH-MB-TPC (int)

CS-F325PLMB Privacy set. P-F325OH-MB-ERC (ext) P-F325OH-MB-TPC (int)

TS-325PLMB Privacy set. P-325OH-MB-ERC (ext) P-325OH-MB-TPC (int)

TS-F325PLMB Privacy set. P-F325OH-MB-ERC (ext) P-F325OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 65: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-65

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

326 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-326PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-326PLMB – Trim set only. No latch or mortise bolt.

CS-F326PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F326PLMB – Trim set only. No latch or mortise bolt.

3"

6"

3" 3"

6"

3"

1 7/

8"

1 7/

8"

2 1/

4"

4 1/

8"

2 1/

4"

2 1/

4"

CS-326PLMB Privacy set. P-326OH-MB-ERC (ext) P-326OH-MB-TPC (int)

CS-F326PLMB Privacy set. P-F326OH-MB-ERC (ext) P-F326OH-MB-TPC (int)

TS-326PLMB Privacy set. P-326OH-MB-ERC (ext) P-326OH-MB-TPC (int)

TS-F326PLMB Privacy set. P-F326OH-MB-ERC (ext) P-F326OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 66: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-66

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

421 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-421PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-421PLMB – Trim set only. No latch or mortise bolt.

CS-F421PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F421PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-421PLMB Privacy set. P-421MB-ERC (ext) P-421MB-TPC (int)

CS-F421PLMB Privacy set. P-F421MB-ERC (ext) P-F421MB-TPC (int)

TS-421PLMB Privacy set. P-421MB-ERC (ext) P-421MB-TPC (int)

TS-F421PLMB Privacy set. P-F421MB-ERC (ext) P-F421MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 67: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-67

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

422 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-422PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-422PLMB – Trim set only. No latch or mortise bolt.

CS-F422PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F422PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-422PLMB Privacy set. P-422MB-ERC (ext) P-422MB-TPC (int)

CS-F422PLMB Privacy set. P-F422MB-ERC (ext) P-F422MB-TPC (int)

TS-422PLMB Privacy set. P-422MB-ERC (ext) P-422MB-TPC (int)

TS-F422PLMB Privacy set. P-F422MB-ERC (ext) P-F422MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 68: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-68

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

423 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-423PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-423PLMB – Trim set only. No latch or mortise bolt.

CS-F423PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F423PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

12"

2 1/2" 2 1/2"

12"

2 1/2"

2 1/

2"

2 1/

2"

9 1/

2"

6"6"6"

CS-423PLMB Privacy set. P-423MB-ERC (ext) P-423MB-TPC (int)

CS-F423PLMB Privacy set. P-F423MB-ERC (ext) P-F423MB-TPC (int)

TS-423PLMB Privacy set. P-423MB-ERC (ext) P-423MB-TPC (int)

TS-F423PLMB Privacy set. P-F423MB-ERC (ext) P-F423MB-TPC (int)

Page 69: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-69

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

424 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-424PLMB Privacy set. P-424MB-ERC (ext) P-424MB-TPC (int)

CS-F424PLMB Privacy set. P-F424MB-ERC (ext) P-F424MB-TPC (int)

TS-424PLMB Privacy set. P-424MB-ERC (ext) P-424MB-TPC (int)

TS-F424PLMB Privacy set. P-F424MB-ERC (ext) P-F424MB-TPC (int)

CS-424PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-424PLMB – Trim set only. No latch or mortise bolt.

CS-F424PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F424PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2"

10"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

2 1/2" 2 1/2"

Page 70: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-70

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-425PLMB Privacy set. P-425MB-ERC (ext) P-425MB-TPC (int)

CS-F425PLMB Privacy set. P-F425MB-ERC (ext) P-F425MB-TPC (int)

TS-425PLMB Privacy set. P-425MB-ERC (ext) P-425MB-TPC (int)

TS-F425PLMB Privacy set. P-F425MB-ERC (ext) P-F425MB-TPC (int)

425 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-425PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-425PLMB – Trim set only. No latch or mortise bolt.

CS-F425PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F425PLMB – Trim set only. No latch or mortise bolt.

3"

13"

3" 3"

13"

3"

4 1/

2"

4 1/

2"

8 1/

2"

3 1/

2"

3 1/

2"

3 1/

2"

Page 71: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-71

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

426 RIDGE PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-426PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-426PLMB – Trim set only. No latch or mortise bolt.

CS-F426PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F426PLMB – Trim set only. No latch or mortise bolt.

2 3/4"

10"

2 3/4"

10"

3" 3"

7"

3 1/

2"

3 1/

2"

3 1/

2"

2 3/4" 2 3/4"

CS-426PLMB Privacy set. P-426MB-ERC (ext) P-426MB-TPC (int)

CS-F426PLMB Privacy set. P-F426MB-ERC (ext) P-F426MB-TPC (int)

TS-426PLMB Privacy set. P-426MB-ERC (ext) P-426MB-TPC (int)

TS-F426PLMB Privacy set. P-F426MB-ERC (ext) P-F426MB-TPC (int)

Page 72: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-72

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

336 CORRUGATED w/BAND PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-336PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-336PLMB – Trim set only. No latch or mortise bolt.

CS-F336PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F336PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

7"

3 1/2" 3 1/2"

7"

3 1/2"

2 1/

4"

2 1/

4" 4 3/

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-336PLMB Privacy set. P-336OH-MB-ERC (ext) P-336OH-MB-TPC (int)

CS-F336PLMB Privacy set. P-F336OH-MB-ERC (ext) P-F336OH-MB-TPC (int)

TS-336PLMB Privacy set. P-336OH-MB-ERC (ext) P-336OH-MB-TPC (int)

TS-F336PLMB Privacy set. P-F336OH-MB-ERC (ext) P-F336OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 73: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-73

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

431 CORRUGATED w/BAND PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-431PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-431PLMB – Trim set only. No latch or mortise bolt.

CS-F431PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F431PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

10"

3 1/2" 3 1/2"

10"

3 1/2"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-431PLMB Privacy set. P-431MB-ERC (ext) P-431MB-TPC (int)

CS-F431PLMB Privacy set. P-F431MB-ERC (ext) P-F431MB-TPC (int)

TS-431PLMB Privacy set. P-431MB-ERC (ext) P-431MB-TPC (int)

TS-F431PLMB Privacy set. P-F431MB-ERC (ext) P-F431MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 74: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-74

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

346 HAMPTON PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-346PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-346PLMB – Trim set only. No latch or mortise bolt.

CS-F346PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F346PLMB – Trim set only. No latch or mortise bolt.

3 3/8"

7 1/

2"

3 3/8" 3 3/8"

7 1/

2"

3 3/8"

2 3/

8" 4 5/

8"

2 1/

4"

2 3/

8"2

1/4"

2 1/

4"

CS-346PLMB Privacy set. P-346OH-MB-ERC (ext) P-346OH-MB-TPC (int)

CS-F346PLMB Privacy set. P-F346OH-MB-ERC (ext) P-F346OH-MB-TPC (int)

TS-346PLMB Privacy set. P-346OH-MB-ERC (ext) P-346OH-MB-TPC (int)

TS-F346PLMB Privacy set. P-F346OH-MB-ERC (ext) P-F346OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 75: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-75

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-440PLMB Privacy set. P-440MB-ERC (ext) P-440MB-TPC (int)

CS-F440PLMB Privacy set. P-F440MB-ERC (ext) P-F440MB-TPC (int)

TS-440PLMB Privacy set. P-440MB-ERC (ext) P-440MB-TPC (int)

TS-F440PLMB Privacy set. P-F440MB-ERC (ext) P-F440MB-TPC (int)

440 HAMPTON PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-440PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-440PLMB – Trim set only. No latch or mortise bolt.

CS-F440PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-F440PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2"

10"

3 1/

4"

3 1/

4" 6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

2 1/2" 2 1/2"

Page 76: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-76

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

441 HAMPTON PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-441PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-441PLMB – Trim set only. No latch or mortise bolt.

CS-F441PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-F441PLMB – Trim set only. No latch or mortise bolt.

3 3/8"

11 1

/2"

3 3/8" 3 3/8"

11 1

/2"

3 3/8"

4" 4"

7 1/

2"

3 1/

2"

3 1/

2"

3 1/

2"

CS-441PLMB Privacy set. P-441MB-ERC (ext) P-441MB-TPC (int)

CS-F441PLMB Privacy set. P-F441MB-ERC (ext) P-F441MB-TPC (int)

TS-441PLMB Privacy set. P-441MB-ERC (ext) P-441MB-TPC (int)

TS-F441PLMB Privacy set. P-F441MB-ERC (ext) P-F441MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 77: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-77

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.ER ONLY. Release cover not available.Combination strike required.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.ER ONLY. Release cover not available.Combination strike required.

CS-355PLMB Privacy set. P-355OH-MB-ERC (ext) P-355OH-MB-TPC (int)

CS-F355PLMB Privacy set. P-F355OH-MB-ERC (ext) P-F355OH-MB-TPC (int)

TS-355PLMB Privacy set. P-355OH-MB-ERC (ext) P-355OH-MB-TPC (int)

TS-F355PLMB Privacy set. P-F355OH-MB-ERC (ext) P-F355OH-MB-TPC (int)

355 TRELLIS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-355PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-355PLMB – Trim set only. No latch or mortise bolt.

CS-F355PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F355PLMB – Trim set only. No latch or mortise bolt.

2 3/4"

6 1/

2"

2 3/4"

6 1/

2"

2 3/

16"

4 5/

16"

2 1/

4"

2 3/

16"

2 3/4" 2 3/4"

2 1/

4"

2 1/

4"1/

4"

1/4"

Page 78: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-78

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

356 TRELLIS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-356PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-356PLMB – Trim set only. No latch or mortise bolt.

CS-F356PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F356PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

6 5/

8"

3 1/2" 3 1/2"

6 5/

8"

3 1/2"

2 1/

4" 4 3/

8"

2 1/

4"

2 1/

4"

2 1/

4"

2 1/

4"1/

4"

1/4"

CS-356PLMB Privacy set. P-356OH-MB-ERC (ext) P-356OH-MB-TPC (int)

CS-F356PLMB Privacy set. P-F356OH-MB-ERC (ext) P-F356OH-MB-TPC (int)

TS-356PLMB Privacy set. P-356OH-MB-ERC (ext) P-356OH-MB-TPC (int)

TS-F356PLMB Privacy set. P-F356OH-MB-ERC (ext) P-F356OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 79: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-79

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

451 TRELLIS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-451PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-451PLMB – Trim set only. No latch or mortise bolt.

CS-F451PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F451PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

10 1

/2"

3 1/2" 3 1/2"

10 1

/2"

3 1/2"

3 1/

2"

3 1/

2"

7"

3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

CS-451PLMB Privacy set. P-451MB-ERC (ext) P-451MB-TPC (int)

CS-F451PLMB Privacy set. P-F451MB-ERC (ext) P-F451MB-TPC (int)

TS-451PLMB Privacy set. P-451MB-ERC (ext) P-451MB-TPC (int)

TS-F451PLMB Privacy set. P-F451MB-ERC (ext) P-F451MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 80: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-80

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

366 DECO PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-366PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-366PLMB – Trim set only. No latch or mortise bolt.

CS-F366PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F366PLMB – Trim set only. No latch or mortise bolt.

3"

7 1/

2"

3" 3"

7 1/

2"

3"

2 5/

8" 4 7/

8"

2 5/

8"

2 1/

4"

2 1/

4"

2 1/

4"

CS-366PLMB Privacy set. P-366OH-MB-ERC (ext) P-366OH-MB-TPC (int)

CS-F366PLMB Privacy set. P-F366OH-MB-ERC (ext) P-F366OH-MB-TPC (int)

TS-366PLMB Privacy set. P-366OH-MB-ERC (ext) P-366OH-MB-TPC (int)

TS-F366PLMB Privacy set. P-F366OH-MB-ERC (ext) P-F366OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 81: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-81

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

461 DECO PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-461PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-461PLMB – Trim set only. No latch or mortise bolt.

CS-F461PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F461PLMB – Trim set only. No latch or mortise bolt.

3"

12"

3" 3"

12"

3"

4 1/

4"

4 1/

4" 7 3/

4"

3 1/

2"

3 1/

2"

3 1/

2"

CS-461PLMB Privacy set. P-461MB-ERC (ext) P-461MB-TPC (int)

CS-F461PLMB Privacy set. P-F461MB-ERC (ext) P-F461MB-TPC (int)

TS-461PLMB Privacy set. P-461MB-ERC (ext) P-461MB-TPC (int)

TS-F461PLMB Privacy set. P-F461MB-ERC (ext) P-F461MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 82: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-82

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1406 CORRUGATED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1406PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1406PLMB – Trim set only. No latch or mortise bolt.

CS-F1406PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1406PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"1

7/8"

1 7/

8" 4 1/

8"

2 1/

4"

2 1/

4"

2 1/

4"

CS-1406PLMB Privacy set. P-1406OH-MB-ERC (ext) P-1406OH-MB-TPC (int)

CS-F1406PLMB Privacy set. P-F1406OH-MB-ERC (ext) P-F1406OH-MB-TPC (int)

TS-1406PLMB Privacy set. P-1406OH-MB-ERC (ext) P-1406OH-MB-TPC (int)

TS-F1406PLMB Privacy set. P-F1406OH-MB-ERC (ext) P-F1406OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 83: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-83

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-1408PLMB Privacy set. P-1408MB-ERC (ext) P-1408MB-TPC (int)

CS-F1408PLMB Privacy set. P-F1408MB-ERC (ext) P-F1408MB-TPC (int)

TS-1408PLMB Privacy set. P-1408MB-ERC (ext) P-1408MB-TPC (int)

TS-F1408PLMB Privacy set. P-F1408MB-ERC (ext) P-F1408MB-TPC (int)

1408 CORRUGATED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1408PLMB – Trim set only. No latch or mortise bolt.

CS-F1408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1408PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

Page 84: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-84

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1410 CORRUGATED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1410PLMB – Trim set only. No latch or mortise bolt.

CS-F1410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1410PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

3" 3"

7"

3 1/

2"

3 1/

2"

3 1/

2"

CS-1410PLMB Privacy set. P-1410MB-ERC (ext) P-1410MB-TPC (int)

CS-F1410PLMB Privacy set. P-F1410MB-ERC (ext) P-F1410MB-TPC (int)

TS-1410PLMB Privacy set. P-1410MB-ERC (ext) P-1410MB-TPC (int)

TS-F1410PLMB Privacy set. P-F1410MB-ERC (ext) P-F1410MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 85: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-85

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.ER ONLY. Release cover not available.Combination strike required.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.ER ONLY. Release cover not available.Combination strike required.

CS-1505PLMB Privacy set. P-1505OH-MB-ERC (ext) P-1505OH-MB-TPC (int)

CS-F1505PLMB Privacy set. P-F1505OH-MB-ERC (ext) P-F1505OH-MB-TPC (int)

TS-1505PLMB Privacy set. P-1505OH-MB-ERC (ext) P-1505OH-MB-TPC (int)

TS-F1505PLMB Privacy set. P-F1505OH-MB-ERC (ext) P-F1505OH-MB-TPC (int)

1505 BANDBOX PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1505PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1505PLMB – Trim set only. No latch or mortise bolt.

CS-F1505PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1505PLMB – Trim set only. No latch or mortise bolt.

2"

6"

2"

2" 2"

4" 2 1/

4"

2"

6"

2"

2 1/

4"

2 1/

4"1/

4"

1/4"

Page 86: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-86

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1506 BANDBOX PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1506PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1506PLMB – Trim set only. No latch or mortise bolt.

CS-F1506PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1506PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

1/4"

1/4"

CS-1506PLMB Privacy set. P-1506OH-MB-ERC (ext) P-1506OH-MB-TPC (int)

CS-F1506PLMB Privacy set. P-F1506OH-MB-ERC (ext) P-F1506OH-MB-TPC (int)

TS-1506PLMB Privacy set. P-1506OH-MB-ERC (ext) P-1506OH-MB-TPC (int)

TS-F1506PLMB Privacy set. P-F1506OH-MB-ERC (ext) P-F1506OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 87: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-87

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1510 BANDBOX PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1510PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1510PLMB – Trim set only. No latch or mortise bolt.

CS-F1510PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1510PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

3" 3"

7"

3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

CS-1510PLMB Privacy set. P-1510MB-ERC (ext) P-1510MB-TPC (int)

CS-F1510PLMB Privacy set. P-F1510MB-ERC (ext) P-F1510MB-TPC (int)

TS-1510PLMB Privacy set. P-1510MB-ERC (ext) P-1510MB-TPC (int)

TS-F1510PLMB Privacy set. P-F1510MB-ERC (ext) P-F1510MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 88: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-88

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-1511PLMB Privacy set. P-1511MB-ERC (ext) P-1511MB-TPC (int)

CS-F1511PLMB Privacy set. P-F1511MB-ERC (ext) P-F1511MB-TPC (int)

TS-1511PLMB Privacy set. P-1511MB-ERC (ext) P-1511MB-TPC (int)

TS-F1511PLMB Privacy set. P-F1511MB-ERC (ext) P-F1511MB-TPC (int)

1511 BANDBOX PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1511PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1511PLMB – Trim set only. No latch or mortise bolt.

CS-F1511PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1511PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

Page 89: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-89

Revised 02/08/16

1512 BANDBOX PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-1512PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1512PLMB – Trim set only. No latch or mortise bolt.

CS-F1512PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1512PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

11 1

/2"

3 1/2" 3 1/2"

11 1

/2"

3 1/2"

3 1/

2"

3 1/

2"

8"

3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

CS-1512PLMB Privacy set. P-1512MB-ERC (ext) P-1512MB-TPC (int)

CS-F1512PLMB Privacy set. P-F1512MB-ERC (ext) P-F1512MB-TPC (int)

TS-1512PLMB Privacy set. P-1512MB-ERC (ext) P-1512MB-TPC (int)

TS-F1512PLMB Privacy set. P-F1512MB-ERC (ext) P-F1512MB-TPC (int)

Page 90: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-90

Revised 02/08/16

HP1505 HAND PEENED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.ER ONLY. Release cover not available.Combination strike required.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.ER ONLY. Release cover not available.Combination strike required.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

CS-HP1505PLMB Privacy set. P-HP1505OH-MB-ERC (ext) P-HP1505OH-MB-TPC (int)

CS-F-HP1505PLMB Privacy set. P-F-HP1505OH-MB-ERC (ext) P-F-HP1505OH-MB-TPC (int)

TS-HP1505PLMB Privacy set. P-HP1505OH-MB-ERC (ext) P-HP1505OH-MB-TPC (int)

TS-F-HP1505PLMB Privacy set. P-F-HP1505OH-MB-ERC (ext) P-F-HP1505OH-MB-TPC (int)

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for turn piece options.

CS-HP1505PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-HP1505PLMB – Trim set only. No latch or mortise bolt.

CS-F-HP1505PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-HP1505PLMB – Trim set only. No latch or mortise bolt.

2"

6"

2" 2"

6"

2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"1/

4"

1/4"

Page 91: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-91

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

HP1506 HAND PEENED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-HP1506PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-HP1506PLMB – Trim set only. No latch or mortise bolt.

CS-F-HP1506PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-HP1506PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

1/4"

1/4"

CS-HP1506PLMB Privacy set. P-HP1506OH-MB-ERC (ext) P-HP1506OH-MB-TPC (int)

CS-F-HP1506PLMB Privacy set. P-F-HP1506OH-MB-ERC (ext) P-F-HP1506OH-MB-TPC (int)

TS-HP1506PLMB Privacy set. P-HP1506OH-MB-ERC (ext) P-HP1506OH-MB-TPC (int)

TS-F-HP1506PLMB Privacy set. P-F-HP1506OH-MB-ERC (ext) P-F-HP1506OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

Page 92: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-92

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

HP1510 HAND PEENED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-HP1510PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-HP1510PLMB – Trim set only. No latch or mortise bolt.

CS-F-HP1510PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-HP1510PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

3" 3"

7"

3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

CS-HP1510PLMB Privacy set. P-HP1510MB-ERC (ext) P-HP1510MB-TPC (int)

CS-F-HP1510PLMB Privacy set. P-F-HP1510MB-ERC (ext) P-F-HP1510MB-TPC (int)

TS-HP1510PLMB Privacy set. P-HP1510MB-ERC (ext) P-HP1510MB-TPC (int)

TS-F-HP1510PLMB Privacy set. P-F-HP1510MB-ERC (ext) P-F-HP1510MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

Page 93: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-93

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

HP1511 HAND PEENED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

CS-HP1511PLMB Privacy set. P-HP1511MB-ERC (ext) P-HP1511MB-TPC (int)

CS-F-HP1511PLMB Privacy set. P-F-HP1511MB-ERC (ext) P-F-HP1511MB-TPC (int)

TS-HP1511PLMB Privacy set. P-HP1511MB-ERC (ext) P-HP1511MB-TPC (int)

TS-F-HP1511PLMB Privacy set. P-F-HP1511MB-ERC (ext) P-F-HP1511MB-TPC (int)

CS-HP1511PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-HP1511PLMB – Trim set only. No latch or mortise bolt.

CS-F-HP1511PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-HP1511PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

Page 94: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-94

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

HP1512 HAND PEENED PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for hand peened knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Hand peened orders do NOT qualify for return and are non-refundable.

CS-HP1512PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-HP1512PLMB – Trim set only. No latch or mortise bolt.

CS-F-HP1512PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-HP1512PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

11 1

/2"

3 1/2" 3 1/2"

11 1

/2"

3 1/2"

3 1/

2"

3 1/

2"

8"

3 1/

2"

3 1/

2"

3 1/

2"1/

4"

1/4"

CS-HP1512PLMB Privacy set. P-HP1512MB-ERC (ext) P-HP1512MB-TPC (int)

CS-F-HP1512PLMB Privacy set. P-F-HP1512MB-ERC (ext) P-F-HP1512MB-TPC (int)

TS-HP1512PLMB Privacy set. P-HP1512MB-ERC (ext) P-HP1512MB-TPC (int)

TS-F-HP1512PLMB Privacy set. P-F-HP1512MB-ERC (ext) P-F-HP1512MB-TPC (int)

Page 95: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-95

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

WV1610 VERTICAL WOOD INLAY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

CS-WV1610PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-WV1610PLMB – Trim set only. No latch or mortise bolt.

CS-F-WV1610PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-WV1610PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

2 1/

4"

2 1/

4"

3 1/

2"

7 3/

4"

1/4" 1/4"3

1/2"

3 1/

2"

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for wood or inlay knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Inlay is available in S1/W1 finishes only.Inlay orders do NOT qualify for return and are non-refundable.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for wood or inlay knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Inlay is available in S1/W1 finishes only.Inlay orders do NOT qualify for return and are non-refundable.

CS-WH1610PLMB Privacy set. P-WH1610MB-ERC (ext) P-WH1610MB-TPC (int)

CS-F-WH1610PLMB Privacy set. P-F-WH1610MB-ERC (ext) P-F-WH1610MB-TPC (int)

TS-WH1610PLMB Privacy set. P-WH1610MB-ERC (ext) P-WH1610MB-TPC (int)

TS-F-WH1610PLMB Privacy set. P-F-WH1610MB-ERC (ext) P-F-WH1610MB-TPC (int)

Page 96: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-96

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

WV1610 VERTICAL WOOD INLAY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-WV1610PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-WV1610PLMB – Trim set only. No latch or mortise bolt.

CS-F-WV1610PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-WV1610PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

2 1/

4"

2 1/

4"

3 1/

2"

7 3/

4"

1/4" 1/4"3

1/2"

3 1/

2"

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for wood or inlay knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Inlay is available in S1/W1 finishes only.Inlay orders do NOT qualify for return and are non-refundable.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.UPCHARGE: A separate charge for wood or inlay knobs, levers or turn pieces applies. Refer to Sections 2 & 4.Inlay is available in S1/W1 finishes only.Inlay orders do NOT qualify for return and are non-refundable.

CS-WV1610PLMB Privacy set. P-WV1610MB-ERC (ext) P-WV1610MB-TPC (int)

CS-F-WV1610PLMB Privacy set. P-F-WV1610MB-ERC (ext) P-F-WV1610MB-TPC (int)

TS-WV1610PLMB Privacy set. P-WV1610MB-ERC (ext) P-WV1610MB-TPC (int)

TS-F-WV1610PLMB Privacy set. P-F-WV1610MB-ERC (ext) P-F-WV1610MB-TPC (int)

Page 97: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-97

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

1711 CIRCLES PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1711PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1711PLMB – Trim set only. No latch or mortise bolt.

CS-F1711PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1711PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

11 1

/8"

2 1/2" 2 1/2"

11 1

/8"

2 1/2"

4 1/

16"

4 1/

16" 7 1/

16" 3"3"3"

2"2"

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.3” center-to-center ONLY.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.3” center-to-center ONLY.

CS-1711PLMB Privacy set. P-1711MB-ERC (ext) P-1711MB-TPC (int)

CS-F1711PLMB Privacy set. P-F1711MB-ERC (ext) P-F1711MB-TPC (int)

TS-1711PLMB Privacy set. P-1711MB-ERC (ext) P-1711MB-TPC (int)

TS-F1711PLMB Privacy set. P-F1711MB-ERC (ext) P-F1711MB-TPC (int)

Page 98: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-98

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

1811 SQUARES PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1811PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1811PLMB – Trim set only. No latch or mortise bolt.

CS-F1811PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1811PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

11 3

/4"

2 1/2" 2 1/2"

11 3

/4"

2 1/2"

4 3/

8"

4 3/

8" 7 3/

8"

3"

2 1/

8"

2 1/

8"

3"3"

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.3” center-to-center ONLY.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.3” center-to-center ONLY.

CS-1811PLMB Privacy set. P-1811MB-ERC (ext) P-1811MB-TPC (int)

CS-F1811PLMB Privacy set. P-F1811MB-ERC (ext) P-F1811MB-TPC (int)

TS-1811PLMB Privacy set. P-1811MB-ERC (ext) P-1811MB-TPC (int)

TS-F1811PLMB Privacy set. P-F1811MB-ERC (ext) P-F1811MB-TPC (int)

Page 99: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-99

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1906 CORDUROY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1906PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1906PLMB – Trim set only. No latch or mortise bolt.

CS-F1906PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1906PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-1906PLMB Privacy set. P-1906OH-MB-ERC (ext) P-1906OH-MB-TPC (int)

CS-F1906PLMB Privacy set. P-F1906OH-MB-ERC (ext) P-F1906OH-MB-TPC (int)

TS-1906PLMB Privacy set. P-1906OH-MB-ERC (ext) P-1906OH-MB-TPC (int)

TS-F1906PLMB Privacy set. P-F1906OH-MB-ERC (ext) P-F1906OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 100: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-100

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

1908 CORDUROY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1908PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1908PLMB – Trim set only. No latch or mortise bolt.

CS-F1908PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1908PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 1/

2"

2 1/

2"

6 1/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-1908PLMB Privacy set. P-1908MB-ERC (ext) P-1908MB-TPC (int)

CS-F1908PLMB Privacy set. P-F1908MB-ERC (ext) P-F1908MB-TPC (int)

TS-1908PLMB Privacy set. P-1908MB-ERC (ext) P-1908MB-TPC (int)

TS-F1908PLMB Privacy set. P-F1908MB-ERC (ext) P-F1908MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 101: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-101

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-1910PLMB Privacy set. P-1910MB-ERC (ext) P-1910MB-TPC (int)

CS-F1910PLMB Privacy set. P-F1910MB-ERC (ext) P-F1910MB-TPC (int)

TS-1910PLMB Privacy set. P-1910MB-ERC (ext) P-1910MB-TPC (int)

TS-F1910PLMB Privacy set. P-F1910MB-ERC (ext) P-F1910MB-TPC (int)

1910 CORDUROY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1910PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1910PLMB – Trim set only. No latch or mortise bolt.

CS-F1910PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1910PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

Page 102: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-102

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-1912PLMB Privacy set. P-1912MB-ERC (ext) P-1912MB-TPC (int)

CS-F1912PLMB Privacy set. P-F1912MB-ERC (ext) P-F1912MB-TPC (int)

TS-1912PLMB Privacy set. P-1912MB-ERC (ext) P-1912MB-TPC (int)

TS-F1912PLMB Privacy set. P-F1912MB-ERC (ext) P-F1912MB-TPC (int)

1912 CORDUROY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1912PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-1912PLMB – Trim set only. No latch or mortise bolt.

CS-F1912PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F1912PLMB – Trim set only. No latch or mortise bolt.

3"

13"

3"

4 3/

16"

4 3/

16"

4 1/

2"

4 1/

2"

3"

13"

3"

4 1/

2"

8 13

/16"

Page 103: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-103

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-1913PLMB Privacy set. P-1913MB-ERC (ext) P-1913MB-TPC (int)

CS-F1913PLMB Privacy set. P-F1913MB-ERC (ext) P-F1913MB-TPC (int)

TS-1913PLMB Privacy set. P-1913MB-ERC (ext) P-1913MB-TPC (int)

TS-F1913PLMB Privacy set. P-F1913MB-ERC (ext) P-F1913MB-TPC (int)

1913 CORDUROY PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-1913PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-1913PLMB – Trim set only. No latch or mortise bolt.

CS-F1913PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F1913PLMB – Trim set only. No latch or mortise bolt.

3 1/2"

13"

3 1/2"

4 1/

2"

4 1/

2"4

1/2"

4 1/

2"

3 1/2"

13"

3 1/2"

8 1/

2"

4 1/

2"

Page 104: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-104

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2106 MESA PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2106PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-2106PLMB – Trim set only. No latch or mortise bolt.

CS-F2106PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F2106PLMB – Trim set only. No latch or mortise bolt.

2 1/4"

6"

2 1/4" 2 1/4"

6"

2 1/4"

2 1/

4" 4"

2 1/

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-2106PLMB Privacy set. P-2106OH-MB-ERC (ext) P-2106OH-MB-TPC (int)

CS-F2106PLMB Privacy set. P-F2106OH-MB-ERC (ext) P-F2106OH-MB-TPC (int)

TS-2106PLMB Privacy set. P-2106OH-MB-ERC (ext) P-2106OH-MB-TPC (int)

TS-F2106PLMB Privacy set. P-F2106OH-MB-ERC (ext) P-F2106OH-MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Page 105: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-105

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

CS-2107PLMB Privacy set. P-2107MB-ERC (ext) P-2107MB-TPC (int)

CS-F2107PLMB Privacy set. P-F2107MB-ERC (ext) P-F2107MB-TPC (int)

TS-2107PLMB Privacy set. P-2107MB-ERC (ext) P-2107MB-TPC (int)

TS-F2107PLMB Privacy set. P-F2107MB-ERC (ext) P-F2107MB-TPC (int)

2107 MESA PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2107PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-2107PLMB – Trim set only. No latch or mortise bolt.

CS-F2107PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2107PLMB – Trim set only. No latch or mortise bolt.

2"

8 3/

4"

2"

2 3/

4"

2 3/

4"

2"

8 3/

4"

2"

6"

3 1/

2"

3 1/

2"

3 1/

2"

Page 106: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-106

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2108 MESA PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2108PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-2108PLMB – Trim set only. No latch or mortise bolt.

CS-F2108PLMB – Complete set with latch and spindle. – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2108PLMB – Trim set only. No latch or mortise bolt.

2 1/4"

8 3/

4"

2 1/4" 2 1/4"

8 3/

4"

2 1/4"

2 3/

4"

2 3/

4"

6" 3 1/

2"

3 1/

2"

3 1/

2"

CS-2108PLMB Privacy set. P-2108MB-ERC (ext) P-2108MB-TPC (int)

CS-F2108PLMB Privacy set. P-F2108MB-ERC (ext) P-F2108MB-TPC (int)

TS-2108PLMB Privacy set. P-2108MB-ERC (ext) P-2108MB-TPC (int)

TS-F2108PLMB Privacy set. P-F2108MB-ERC (ext) P-F2108MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 107: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-107

Revised 02/08/16

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2109 MESA PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2109PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-2109PLMB – Trim set only. No latch or mortise bolt.

CS-F2109PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F2109PLMB – Trim set only. No latch or mortise bolt.

1 3/4"

9"

1 3/4" 1 3/4"

9"

1 3/4"

3" 3"

6" 3 1/

2"

3 1/

2"

3 1/

2"

CS-2109PLMB Privacy set. P-2109MB-ERC (ext) P-2109MB-TPC (int)

CS-F2109PLMB Privacy set. P-F2109MB-ERC (ext) P-F2109MB-TPC (int)

TS-2109PLMB Privacy set. P-2109MB-ERC (ext) P-2109MB-TPC (int)

TS-F2109PLMB Privacy set. P-F2109MB-ERC (ext) P-F2109MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

Page 108: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-108

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2110 MESA PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2110PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-2110PLMB – Trim set only. No latch or mortise bolt.

CS-F2110PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F2110PLMB – Trim set only. No latch or mortise bolt.

2 1/4"

10"

2 1/4" 2 1/4"

10"

2 1/4"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-2110PLMB Privacy set. P-2110MB-ERC (ext) P-2110MB-TPC (int)

CS-F2110PLMB Privacy set. P-F2110MB-ERC (ext) P-F2110MB-TPC (int)

TS-2110PLMB Privacy set. P-2110MB-ERC (ext) P-2110MB-TPC (int)

TS-F2110PLMB Privacy set. P-F2110MB-ERC (ext) P-F2110MB-TPC (int)

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Page 109: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-109

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

2111 MESA PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-2111PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-2111PLMB – Trim set only. No latch or mortise bolt.

CS-F2111PLMB – Complete set with passage latch, mortise bolt and spindle. OR TS-F2111PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

11"

2 1/2"

3 3/

4"

3 3/

4" 7 1/

4"

3 1/

2"

3 1/

2"

3 1/

2"

2 1/2"

11"

2 1/2"

CS-2111PLMB Privacy set. P-2111MB-ERC (ext) P-2111MB-TPC (int)

CS-F2111PLMB Privacy set. P-F2111MB-ERC (ext) P-F2111MB-TPC (int)

TS-2111PLMB Privacy set. P-2111MB-ERC (ext) P-2111MB-TPC (int)

TS-F2111PLMB Privacy set. P-F2111MB-ERC (ext) P-F2111MB-TPC (int)

Page 110: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-110

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

CS-2206PLMB Privacy set. P-2206OH-MB-ERC (ext) P-2206OH-MB-TPC (int)

CS-F2206PLMB Privacy set. P-F2206OH-MB-ERC (ext) P-F2206OH-MB-TPC (int)

TS-2206PLMB Privacy set. P-2206OH-MB-ERC (ext) P-2206OH-MB-TPC (int)

TS-F2206PLMB Privacy set. P-F2206OH-MB-ERC (ext) P-F2206OH-MB-TPC (int)

2206 BURLAP PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2206PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-2206PLMB – Trim set only. No latch or mortise bolt.

CS-F2206PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2206PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"

1 7/

8"

1 7/

8" 4 1/

8"

2 1/

4"

2 1/

4"

2 1/

4"

Page 111: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-111

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-2208PLMB Privacy set. P-2208MB-ERC (ext) P-2208MB-TPC (int)

CS-F2208PLMB Privacy set. P-F2208MB-ERC (ext) P-F2208MB-TPC (int)

TS-2208PLMB Privacy set. P-2208MB-ERC (ext) P-2208MB-TPC (int)

TS-F2208PLMB Privacy set. P-F2208MB-ERC (ext) P-F2208MB-TPC (int)

2208 BURLAP PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2208PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-2208PLMB – Trim set only. No latch or mortise bolt.

CS-F2208PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2208PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

Page 112: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-112

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-2210PLMB Privacy set. P-2210MB-ERC (ext) P-2210MB-TPC (int)

CS-F2210PLMB Privacy set. P-F2210MB-ERC (ext) P-F2210MB-TPC (int)

TS-2210PLMB Privacy set. P-2210MB-ERC (ext) P-2210MB-TPC (int)

TS-F2210PLMB Privacy set. P-F2210MB-ERC (ext) P-F2210MB-TPC (int)

2210 BURLAP PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

CS-2210PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-2210PLMB – Trim set only. No latch or mortise bolt.

CS-F2210PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2210PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

3 1/

8"

3 1/

8"

6 7/

8" 3 1/

2"

3 1/

2"

3 1/

2"

Page 113: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-113

Revised 02/08/16

N949 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

CS-N949PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N949PLMB – Trim set only. No latch or mortise bolt.

CS-F-N949PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N949PLMB – Trim set only. No latch or mortise bolt.

2"

6"

2" 2"

6"

2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-N949PLMB Privacy set. P-N949OH-MB-ERC (ext) P-N949OH-MB-TPC (int)

CS-F-N949PLMB Privacy set. P-F-N949OH-MB-ERC (ext) P-F-N949OH-MB-TPC (int)

TS-N949PLMB Privacy set. P-N949OH-MB-ERC (ext) P-N949OH-MB-TPC (int)

TS-F-N949PLMB Privacy set. P-F-N949OH-MB-ERC (ext) P-F-N949OH-MB-TPC (int)

Page 114: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-114

Revised 02/08/16

N950 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

CS-N950PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N950PLMB – Trim set only. No latch or mortise bolt.

CS-F-N950PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N950PLMB – Trim set only. No latch or mortise bolt.

2"

8 3/

4"

2" 2"

8 3/

4"

2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-N950PLMB Privacy set. P-N950MB-ERC (ext) P-N950MB-TPC (int)

CS-F-N950PLMB Privacy set. P-F-N950MB-ERC (ext) P-F-N950MB-TPC (int)

TS-N950PLMB Privacy set. P-N950MB-ERC (ext) P-N950MB-TPC (int)

TS-F-N950PLMB Privacy set. P-F-N950MB-ERC (ext) P-F-N950MB-TPC (int)

Page 115: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-115

Revised 02/08/16

N951 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

CS-N951PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N951PLMB – Trim set only. No latch or mortise bolt.

CS-F-N951PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N951PLMB – Trim set only. No latch or mortise bolt.

2"

10"

2" 2"

10"

2"

2 3/

8"

2 3/

8"

7 5/

8" 4 1/

2"

4 1/

2"

4 1/

2"

CS-N951PLMB Privacy set. P-N951MB-ERC (ext) P-N951MB-TPC (int)

CS-F-N951PLMB Privacy set. P-F-N951MB-ERC (ext) P-F-N951MB-TPC (int)

TS-N951PLMB Privacy set. P-N951MB-ERC (ext) P-N951MB-TPC (int)

TS-F-N951PLMB Privacy set. P-F-N951MB-ERC (ext) P-F-N951MB-TPC (int)

Page 116: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-116

Revised 02/08/16

N952 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-N952PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N952PLMB – Trim set only. No latch or mortise bolt.

CS-F-N952PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N952PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

10"

2 1/2" 2 1/2"

10"

2 1/2"

2 1/

4"

2 1/

4"

7 3/

4" 4 1/

2"

4 1/

2"

4 1/

2"

CS-N952PLMB Privacy set. P-N952MB-ERC (ext) P-N952MB-TPC (int)

CS-F-N952PLMB Privacy set. P-F-N952MB-ERC (ext) P-F-N952MB-TPC (int)

TS-N952PLMB Privacy set. P-N952MB-ERC (ext) P-N952MB-TPC (int)

TS-F-N952PLMB Privacy set. P-F-N952MB-ERC (ext) P-F-N952MB-TPC (int)

Page 117: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-117

Revised 02/08/16

N953 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-N953PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N953PLMB – Trim set only. No latch or mortise bolt.

CS-F-N953PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N953PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-N953PLMB Privacy set. P-N953MB-ERC (ext) P-N953MB-TPC (int)

CS-F-N953PLMB Privacy set. P-F-N953MB-ERC (ext) P-F-N953MB-TPC (int)

TS-N953PLMB Privacy set. P-N953MB-ERC (ext) P-N953MB-TPC (int)

TS-F-N953PLMB Privacy set. P-F-N953MB-ERC (ext) P-F-N953MB-TPC (int)

Page 118: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-118

Revised 02/08/16

N954 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

CS-N954PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N954PLMB – Trim set only. No latch or mortise bolt.

CS-F-N954PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N954PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"

2" 2"

4" 2 1/

4"

2 1/

4"

2 1/

4"

CS-N954PLMB Privacy set. P-N954OH-MB-ERC (ext) P-N954OH-MB-TPC (int)

CS-F-N954PLMB Privacy set. P-F-N954OH-MB-ERC (ext) P-F-N954OH-MB-TPC (int)

TS-N954PLMB Privacy set. P-N954OH-MB-ERC (ext) P-N954OH-MB-TPC (int)

TS-F-N954PLMB Privacy set. P-F-N954OH-MB-ERC (ext) P-F-N954OH-MB-TPC (int)

Page 119: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-119

Revised 02/08/16

N955 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-N955PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N955PLMB – Trim set only. No latch or mortise bolt.

CS-F-N955PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N955PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

3 1/

4"

3 1/

4" 6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-N955PLMB Privacy set. P-N955MB-ERC (ext) P-N955MB-TPC (int)

CS-F-N955PLMB Privacy set. P-F-N955MB-ERC (ext) P-F-N955MB-TPC (int)

TS-N955PLMB Privacy set. P-N955MB-ERC (ext) P-N955MB-TPC (int)

TS-F-N955PLMB Privacy set. P-F-N955MB-ERC (ext) P-F-N955MB-TPC (int)

Page 120: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-120

Revised 02/08/16

N957 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-N957PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N957PLMB – Trim set only. No latch or mortise bolt.

CS-F-N957PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N957PLMB – Trim set only. No latch or mortise bolt.

3"

12"

3" 3"

12"

3"

3 1/

2"

3 1/

2"

8 1/

2"

4 1/

2"

4 1/

2"

4 1/

2"

CS-N957PLMB Privacy set. P-N957MB-ERC (ext) P-N957MB-TPC (int)

CS-F-N957PLMB Privacy set. P-F-N957MB-ERC (ext) P-F-N957MB-TPC (int)

TS-N957PLMB Privacy set. P-N957MB-ERC (ext) P-N957MB-TPC (int)

TS-F-N957PLMB Privacy set. P-F-N957MB-ERC (ext) P-F-N957MB-TPC (int)

Page 121: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-121

Revised 02/08/16

N979 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.Combination strike required.

CS-N979PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N979PLMB – Trim set only. No latch or mortise bolt.

CS-F-N979PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N979PLMB – Trim set only. No latch or mortise bolt.

1 1/2"

6"

1 1/2" 1 1/2"

6"

1 1/2"

2"

4" 2 1/

4"

2"2

1/4"

2 1/

4"

CS-N979PLMB Privacy set. P-N979OH-MB-ERC (ext) P-N979OH-MB-TPC (int)

CS-F-N979PLMB Privacy set. P-F-N979OH-MB-ERC (ext) P-F-N979OH-MB-TPC (int)

TS-N979PLMB Privacy set. P-N979OH-MB-ERC (ext) P-N979OH-MB-TPC (int)

TS-F-N979PLMB Privacy set. P-F-N979OH-MB-ERC (ext) P-F-N979OH-MB-TPC (int)

Page 122: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-122

Revised 02/08/16

N980 NOVUS PASSAGE LATCH/MORTISE BOLT PRIVACY SETS Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Will not cover 2 1/8” bore.

CS-N980PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-N980PLMB – Trim set only. No latch or mortise bolt.

CS-F-N980PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F-N980PLMB – Trim set only. No latch or mortise bolt.

1 1/2"

10 1

/2"

1 1/2" 1 1/2"

10 1

/2"

1 1/2"

4" 4"

6 1/

2" 3 1/

2"

3 1/

2"

3 1/

2"

CS-N980PLMB Privacy set. P-N980MB-ERC (ext) P-N980MB-TPC (int)

CS-F-N980PLMB Privacy set. P-F-N980MB-ERC (ext) P-F-N980MB-TPC (int)

TS-N980PLMB Privacy set. P-N980MB-ERC (ext) P-N980MB-TPC (int)

TS-F-N980PLMB Privacy set. P-F-N980MB-ERC (ext) P-F-N980MB-TPC (int)

Page 123: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-123

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

2406 RIDGE BURLAP PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.Combination strike required.

CS-2406PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-2406PLMB – Trim set only. No latch or mortise bolt.

CS-F2406PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2406PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

6"

2 1/2" 2 1/2"

6"

2 1/2"2

1/16

"

2 1/

16" 2

1/4"

3 15

/16"

2 1/

4"

2 1/

4"

CS-2406PLMB Privacy set. P-2406OH-MB-ERC (ext) P-2406OH-MB-TPC (int)

CS-F2406PLMB Privacy set. P-F2406OH-MB-ERC (ext) P-F2406OH-MB-TPC (int)

TS-2406PLMB Privacy set. P-2406OH-MB-ERC (ext) P-2406OH-MB-TPC (int)

TS-F2406PLMB Privacy set. P-F2406OH-MB-ERC (ext) P-F2406OH-MB-TPC (int)

Page 124: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-124

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

2408 RIDGE BURLAP PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Complete sets with tubular passage latch, mortise bolt and spindle.

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-2408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-2408PLMB – Trim set only. No latch or mortise bolt.

CS-F2408PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2408PLMB – Trim set only. No latch or mortise bolt.

2 1/2"

8 3/

4"

2 1/2" 2 1/2"

8 3/

4"

2 1/2"

2 3/

4"

2 3/

4"

6"

3 1/

2"

3 1/

2"

3 1/

2"

CS-2408PLMB Privacy set. P-2408MB-ERC (ext) P-2408MB-TPC (int)

CS-F2408PLMB Privacy set. P-F2408MB-ERC (ext) P-F2408MB-TPC (int)

TS-2408PLMB Privacy set. P-2408MB-ERC (ext) P-2408MB-TPC (int)

TS-F2408PLMB Privacy set. P-F2408MB-ERC (ext) P-F2408MB-TPC (int)

Page 125: Spec 16G Passage Latch / Mortise Bolt Privacy Door Sets

Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w. s u n v a l l e y b r o n z e . c o m

PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited.

16-125

Revised 02/08/16

Illustrations are for demonstration purposes only. Any knob, lever or ring pull can be combined with any style or size escutcheon plate.Refer to Section 4 for release cover & turn piece options.

2410 RIDGE BURLAP PASSAGE LATCH/MORTISE BOLT PRIVACY SETS

Trim sets for tubular passage latch, mortise bolt and spindle. No latch or mortise bolt included.

Complete sets with tubular passage latch, mortise bolt and spindle.

Specify manufacturer of latch and mortise bolt to be used.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

2 3/8” or 2 3/4” backset standard. Please specify.Door handing and thickness are required for all tubular mortise bolt privacy sets.Always specify lever/knob design.

CS-2410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-2410PLMB – Trim set only. No latch or mortise bolt.

CS-F2410PLMB – Complete set with passage latch,

mortise bolt and spindle. OR TS-F2410PLMB – Trim set only. No latch or mortise bolt.

3"

10"

3" 3"

10"

3"

3 1/

4"

3 1/

4"

6 3/

4" 3 1/

2"

3 1/

2"

3 1/

2"

CS-2410PLMB Privacy set. P-2410MB-ERC (ext) P-2410MB-TPC (int)

CS-F2410PLMB Privacy set. P-F24102MB-ERC (ext) P-F2410MB-TPC (int)

TS-2410PLMB Privacy set. P-2410MB-ERC (ext) P-2410MB-TPC (int)

TS-F2410PLMB Privacy set. P-F2410MB-ERC (ext) P-F2410MB-TPC (int)