Top Banner
2011-2013 Microchip Technology Inc. DS20002281B-page 1 MTD6505 180° Sinusoidal Drive for high efficiency and low acoustic noise Position Sensorless BLDC Drivers (No Hall effect sensor required) Integrated Power Transistors Supports 2V to 5.5V Power Supplies Programming Resistor (R PROG ) settings to fit motor constant (K M ) range from 3.25 mV/Hz to 52 mV/Hz Direction Control: - Forward direction: connect DIR pin to GND or leave floating - Reverse direction: connect DIR pin to V BIAS or 3V Speed Control through Power Supply Modulation (PSM) and/or Pulse-Width Modulation (PWM) Built-in Frequency Generator (FG Output Signal) Built-in Lockup Protection and Automatic Recovery Circuit Built-in Overcurrent Limitation Built-in Thermal Shutdown Protection Built-in Over Voltage Protection No External Tuning Required Available Package: 10-Lead 3mm x 3mm UDFN Applications Notebook CPU Cooling Fans 5V 3-Phase BLDC The MTD6505 device is a 3-phase full-wave sensorless driver for brushless DC (BLDC) motors. It features 180° sinusoidal drive, high torque output and silent drive. With the adaptive features, parameters and wide range of power supplies (2V to 5.5V), the MTD6505 is intended to cover a broad range of motor characteristics, while requiring minimum external components. Speed control can be achieved through either PSM or PWM. The compact packaging and the minimal bill-of- material make the MTD6505 device extremely cost- efficient in fan applications. For example, the CPU cooling fans in notebook computers require designs that provide low acoustic noise, low mechanical vibration, and are highly efficient. The frequency generator (FG) output enables precision speed control in closed-loop applications. The MTD6505 device includes Lockup Protection mode to turn off the output current when the motor is in a lock condition, with an automatic recovery feature to restart the fan when the lock condition is removed. Motor overcurrent limitation and thermal shutdown protection are included for safety enhanced operations. The MTD6505 is available in a compact, thermally enhanced, 3mm x 3mm 10-lead UDFN package. Package Types MTD6505 3x3 UDFN* V BIAS R PROG OUT2 FG PWM DIR V DD GND 1 2 3 5 10 9 8 6 OUT1 OUT3 4 7 EP 11 *Includes Exposed Thermal Pad (EP); see Table 3-1. Sinusoidal Sensorless 3-Phase Brushless DC (BLDC) Fan Motor Driver
22

Sinusoidal Sensorless 3-Phase Brushless DC (BLDC) Fan ...docs-europe.electrocomponents.com/webdocs/116f/... · sensorless driver for brushless DC (BLDC) motors. It features 180°

Apr 03, 2018

Download

Documents

nguyennhu
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
  • MTD6505Sinusoidal Sensorless 3-Phase Brushless DC (BLDC)

    Features 180 Sinusoidal Drive for high efficiency and low

    acoustic noise

    Position Sensorless BLDC Drivers (No Hall effect sensor required)

    Integrated Power Transistors

    Supports 2V to 5.5V Power Supplies

    Programming Resistor (RPROG) settings to fit motor constant (KM) range from 3.25 mV/Hz to 52 mV/Hz

    Direction Control:

    - Forward direction: connect DIR pin to GND or leave floating

    - Reverse direction: connect DIR pin to VBIAS or 3V

    Speed Control through Power Supply Modulation (PSM) and/or Pulse-Width Modulation (PWM)

    Built-in Frequency Generator (FG Output Signal)

    Built-in Lockup Protection and Automatic Recovery Circuit

    Built-in Overcurrent Limitation

    Built-in Thermal Shutdown Protection

    Built-in Over Voltage Protection

    No External Tuning Required

    Available Package:10-Lead 3mm x 3mm UDFN

    Applications Notebook CPU Cooling Fans

    5V 3-Phase BLDC

    DescriptionThe MTD6505 device is a 3-phase full-wavesensorless driver for brushless DC (BLDC) motors. Itfeatures 180 sinusoidal drive, high torque output andsilent drive. With the adaptive features, parameters andwide range of power supplies (2V to 5.5V), theMTD6505 is intended to cover a broad range of motorcharacteristics, while requiring minimum externalcomponents. Speed control can be achieved througheither PSM or PWM.

    The compact packaging and the minimal bill-of-material make the MTD6505 device extremely cost-efficient in fan applications. For example, the CPUcooling fans in notebook computers require designsthat provide low acoustic noise, low mechanicalvibration, and are highly efficient. The frequencygenerator (FG) output enables precision speed controlin closed-loop applications.

    The MTD6505 device includes Lockup Protectionmode to turn off the output current when the motor is ina lock condition, with an automatic recovery feature torestart the fan when the lock condition is removed.Motor overcurrent limitation and thermal shutdownprotection are included for safety enhanced operations.

    The MTD6505 is available in a compact, thermallyenhanced, 3mm x 3mm 10-lead UDFN package.

    Package Types

    MTD65053x3 UDFN*

    VBIAS

    RPROG

    OUT2

    FG PWMDIRVDD

    GND

    123

    5

    10

    98

    6

    OUT1 OUT34 7

    EP11

    *Includes Exposed Thermal Pad (EP); see Table 3-1.

    Fan Motor Driver

    2011-2013 Microchip Technology Inc. DS20002281B-page 1

  • MTD6505

    Functional Block Diagram

    Thermal protection

    VBIAS

    OUT1

    OUT2CPU + peripherals

    PWM

    FG

    OUT3

    VDD

    Short-circuitprotection

    Out

    put D

    rive

    Circ

    uit

    Motor PhaseDetection

    Circuit

    Overcurrentprotection

    GNDDIR

    Non-volatile memory

    RPROG senseRPROG

    VDD

    Adjustable Km

    DS20002281B-page 2 2011-2013 Microchip Technology Inc.

  • MTD6505

    Typical Application

    MTD

    6505

    1

    2

    3

    4

    5

    10

    9

    8

    7

    6

    FG

    VBIAS

    OUT1

    OUT2 GND

    OUT3

    VDD

    DIR

    PWMR2

    C1

    VDD

    C2

    VDD

    R1

    KM0 KM3KM1, 2

    RPROG

    VBIASVBIAS

    Recommended External Components for Typical Application

    Element Type/Value Comment

    C1 >1 F Connect as close as possible to IC input pinsC2 >1 F Connect as close as possible to IC input pinsR1 >10 k Connect to Vlogic on microcontroller side (FG pull up)R2 3.9 k or 24 k Select appropriate programming resistor value, see

    Table 4-2

    2011-2013 Microchip Technology Inc. DS20002281B-page 3

  • MTD6505

    NOTES:

    DS20002281B-page 4 2011-2013 Microchip Technology Inc.

  • MTD6505

    1.0 ELECTRICAL CHARACTERISTICS

    Absolute Maximum RatingsPower Supply Voltage (VDD_MAX) ...................... -0.7 to +7.0VMaximum Output Voltage (VOUT_MAX) ............... -0.7 to +7.0VMaximum Output Current(2) (IOUT_MAX) ....................1000 mAFG Maximum Output Voltage (VFG_MAX) ........... -0.7 to +7.0VFG Maximum Output Current (IFG_MAX) ......................5.0 mAVBIAS Maximum Voltage (VBIAS_MAX) ................ -0.7 to +4.0VPWM Maximum Voltage (VPWM_MAX) ................ -0.7 to +7.0VAllowable Power Dissipation(1)(PD_MAX).........................1.5WMax Junction Temperature (TJ)................................... +150CESD protection on all pins ...................................................2 kV

    Notice: Stresses above those listed under MaximumRatings may cause permanent damage to the device.This is a stress rating only and functional operation ofthe device at those or any other conditions above thoseindicated in the operational listings of this specificationis not implied. Exposure to maximum rating conditionsfor extended periods may affect device reliability.

    Note 1: Reference PCB, according to JEDECstandard EIA/JESD 51-9.

    2: IOUT is also internally limited, according to thelimits defined in the Electrical Charac-teristics table.

    ELECTRICAL CHARACTERISTICSElectrical Specifications: Unless otherwise specified, all limits are established for VDD = 2.0V to 5.5V, TA = +25C

    Parameters Sym Min Typ Max Units Conditions

    Power Supply Voltage VDD 2 5.5 V

    Power Supply Current IVDD 5 10 mA VDD = 5V

    Standby Current IVDD_STB 30 40 A PWM = 0V, VDD = 5V (Standby mode)

    OUT1, 2, 3High Resistance

    RON(H) 0.75 1.1 IOUT = 0.5A, VDD = 5VNote 3

    OUT1, 2, 3Low Resistance

    RON(L) 0.75 1.3 IOUT = 0.5A, VDD = 5VNote 3

    OUT1, 2, 3Total Resistance

    RON(H+L) 1.5 IOUT = 0.5A, VDD = 5V

    VBIAS InternalSupply Voltage

    VBIAS 3 V VDD = 3.2V to 5.5V

    VDD 0.2 V VDD < 3.2V

    PWM Input Frequency fPWM 1 100 kHz

    PWM Input H Level VPWM_H 0.55*VDD VDD V VDD 4.5V

    PWM Input L Level VPWM_L 0 0.2*VDD V VDD 4.5V

    PWM Internal Pull-Up Resistor

    RPWM_0 266 k PWM = 0V

    PWM Internal Pull-Up Resistor

    RPWM 133 k PWM duty-cycle > 0%

    DIR Input H Level VDIR_H 0.55*VDD VDD V VDD 4.5V

    DIR Input L Level VDIR_L 0 0.2*VDD V VDD 4.5V

    DIR Internal Pull-Down Resistor

    RDIR 100 200 k

    FG Output Pin Low Level Voltage

    VOL_FG 0.25 V IFG = -1 mA

    Note 1: 750 mA is the standard option for MTD6505. Additional overcurrent protection levels are available upon request. Please contact factory for different overcurrent protection values.

    2: Related to the internal oscillator frequency (see Figure 2-1).3: Minimum and maximum parameter is not production tested and is specified by design and validation.

    2011-2013 Microchip Technology Inc. DS20002281B-page 5

  • MTD6505

    FG Output Pin Leakage Current

    ILH_FG -10 10 A VFG = 5.5V

    Lock Protection Operating Time

    TRUN 0.5 s

    Lock Protection Waiting Time

    TWAIT 4.5 5 5.5 s Note 2

    Overcurrent Protection IOC_MOT 750 mA

    Overvoltage Protection VOV 7.2 V

    Short Protection on High Side

    IOC_SW_H 2.57 A

    Short Protection on Low Side

    IOC_SW_L -2.83 A

    Thermal Shutdown TSD 170 C

    Thermal Shutdown Hysteresis

    TSD_HYS 25 C

    TEMPERATURE SPECIFICATIONSElectrical Specifications: Unless otherwise specified, all limits are established for VDD = 5.5V to 2.0V, TA = +25C.

    Parameters Sym Min Typ Max Units Conditions

    Temperature RangesOperating Temperature TOPR -40 +125 CStorage Temperature Range TSTG -55 +150 CThermal Package ResistancesThermal Resistance, 10L-UDFN JA 96.6 C/W

    JC 12 C/W

    ELECTRICAL CHARACTERISTICS (CONTINUED)Electrical Specifications: Unless otherwise specified, all limits are established for VDD = 2.0V to 5.5V, TA = +25C

    Parameters Sym Min Typ Max Units Conditions

    Note 1: 750 mA is the standard option for MTD6505. Additional overcurrent protection levels are available upon request. Please contact factory for different overcurrent protection values.

    2: Related to the internal oscillator frequency (see Figure 2-1).3: Minimum and maximum parameter is not production tested and is specified by design and validation.

    DS20002281B-page 6 2011-2013 Microchip Technology Inc.

  • MTD6505

    2.0 TYPICAL PERFORMANCE CURVES

    Note: Unless indicated, TA = +25C, VDD = 5.5V to 2.0V, OUT1, 2, 3 and PWM open.

    FIGURE 2-1: Oscillator Frequency Deviation vs. Temperature.

    FIGURE 2-2: Internal Regulated Voltage (VBIAS) vs Temperature.

    FIGURE 2-3: Internal Regulated Voltage (VBIAS) vs Supply Voltage (VDD).

    FIGURE 2-4: Inputs (PWM, DIR) VIL vs. Temperature.

    FIGURE 2-5: Inputs (PWM, DIR) VIH vs. Temperature.

    FIGURE 2-6: Outputs RON High Side Resistance vs. Temperature.

    Note: The graphs and tables provided following this note are a statistical summary based on a limited number ofsamples and are provided for informational purposes only. The performance characteristics listed hereinare not tested or guaranteed. In some graphs or tables, the data presented may be outside the specifiedoperating range (e.g., outside specified power supply range) and therefore outside the warranted range.

    -3-2.5

    -2-1.5

    -1-0.5

    00.5

    1

    or F

    requ

    eny

    Dev

    iatio

    n (%

    )

    VDD = 5.5V

    VDD = 2V

    -4.5-4

    -3.5-3

    -2.5-2

    -1.5-1

    -0.50

    0.51

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    Osc

    illat

    or F

    requ

    eny

    Dev

    iatio

    n (%

    )

    Temperature (C)

    VDD = 5.5V

    VDD = 2V

    3 04

    3.06

    3.08

    3.1

    3.12

    3.14

    V BIA

    S(V

    )

    3

    3.02

    3.04

    3.06

    3.08

    3.1

    3.12

    3.14

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    V BIA

    S(V

    )

    Temperature (C)

    1

    1.5

    2

    2.5

    3

    3.5

    V BIA

    S(V

    )

    0

    0.5

    1

    1.5

    2

    2.5

    3

    3.5

    2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

    V BIA

    S(V

    )

    VDD(V)

    1

    1.5

    2

    2.5

    PWM

    VIL

    (V)

    VDD = 5.5VDD = 5.5VDD = 5.5V

    VDD = 2V

    0

    0.5

    1

    1.5

    2

    2.5

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    PWM

    VIL

    (V)

    Temperature (C)

    VDD = 5.5VDD = 5.5VDD = 5.5V

    VDD = 2V

    1

    1.5

    2

    2.5

    3PW

    M V

    IH(V

    )

    VDD = 5.5V

    VDD = 2V

    0

    0.5

    1

    1.5

    2

    2.5

    3

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    PWM

    VIH

    (V)

    Temperature (C)

    VDD = 5.5V

    VDD = 2V

    1 52

    2.53

    3.54

    4.55

    5.56

    RO

    N H

    igh

    Side

    () VDD = 2V

    00.5

    11.5

    22.5

    33.5

    44.5

    55.5

    6

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    RO

    N H

    igh

    Side

    ()

    Temperature (C)

    VDD = 5.5V

    VDD = 2V

    2011-2013 Microchip Technology Inc. DS20002281B-page 7

  • MTD6505

    Note: Unless indicated, TA = +25C, VDD = 5.5V to 2.0V, OUT1, 2, 3 and PWM open.

    FIGURE 2-7: Outputs RON Low Side Resistance vs. Temperature.

    FIGURE 2-8: Supply Current vs. Temperature.

    FIGURE 2-9: Stand-By Current vs. Temperature.

    FIGURE 2-10: PWM Pull-Up Current vs. Temperature.

    FIGURE 2-11: Typical Output on Start-up.

    FIGURE 2-12: Typical Outputs on Closed Loop.

    22.5

    33.5

    44.5

    55.5

    6

    ON

    Low

    Sid

    e (

    )

    VDD = 2V

    00.5

    11.5

    22.5

    33.5

    44.5

    55.5

    6

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    RO

    N L

    ow S

    ide

    ()

    Temperature (C)

    VDD = 5.5V

    VDD = 2V

    2

    3

    4

    5

    6

    7

    VDD

    Cur

    rent

    (mA

    )

    VDD = 2V

    VDD = 5.5V

    0

    1

    2

    3

    4

    5

    6

    7

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    I VD

    DC

    urre

    nt (m

    A)

    Temperature (C)

    VDD = 2V

    VDD = 5.5V

    20

    30

    40

    50

    60

    D_S

    TBC

    urre

    nt (

    A)

    VDD = 5.5V

    0

    10

    20

    30

    40

    50

    60

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    I VD

    D_S

    TBC

    urre

    nt (

    A)

    Temperature (C)

    VDD = 5.5V

    VDD = 2V

    -30

    -25

    -20

    -15

    -10

    -5

    0

    Pull-

    Up

    Cur

    rent

    (A

    )

    VDD = 2V

    -40

    -35

    -30

    -25

    -20

    -15

    -10

    -5

    0

    -40 -25 -10 5 20 35 50 65 80 95 110 125

    PWM

    Pul

    l-Up

    Cur

    rent

    (A

    )

    Temperature (C)

    VDD = 2V

    VDD = 5.5V

    DS20002281B-page 8 2011-2013 Microchip Technology Inc.

  • MTD6505

    3.0 PIN DESCRIPTIONSThe descriptions of the pins are listed in Table 3-1.

    TABLE 3-1: MTD6505 PIN FUNCTION TABLEPin

    Number Type Name Function

    1 O FG Motor speed indication output2 I RPROG Km parameter setting with external resistors, see Table 4-2 for values3 VBIAS Internal regulator output (for decoupling only)4 O OUT1 Single phase coil output pin5 O OUT2 Single phase coil output pin6 GND Negative voltage supply (ground)7 O OUT3 Single phase coil output pin8 VDD Positive voltage supply for motor driver9 I DIR Motor Rotation Direction

    - Forward direction: connect pin to GND or leave floating- Reverse direction: connect pin to VBIAS

    10 I PWM PWM input signal for speed control11 EP Exposed pad (Connect to the ground plan for better thermal dissipation)

    Legend: I = Input; O = Output

    2011-2013 Microchip Technology Inc. DS20002281B-page 9

  • MTD6505

    NOTES:

    DS20002281B-page 10 2011-2013 Microchip Technology Inc.

  • MTD6505

    4.0 FUNCTIONAL DESCRIPTIONThe MTD6505 generates a full-wave signal to drive a3-phase BLDC motor. High efficiency and low-powerconsumption are achieved due to CMOS transistorsand synchronous rectification drive type.

    4.1 Speed ControlThe rotational speed of the motor can be controlledeither through the PWM digital input signal or by actingdirectly on the power supply (VDD). When the PWMsignal is High (or left open), the motor rotates at fullspeed. When the PWM signal is low, the IC outputs areset to high-impedance and the motor is stopped.

    By changing the PWM duty cycle, the speed can beadjusted. Thus, the user has freedom to choose thePWM system frequency within a wide range (from1 kHz to 100 kHz).

    Since the PWM pin has an internal pull-up resistorconnected to VDD, it is recommended to drive itbetween 0V and High-Z. The PWM driver must be ableto support the pull-up resistor current, to drive the pin.See PWM Internal Pull-Up Resistor in Section 1.0,Electrical Characteristics.The output transistor activation always occurs at a fixedrate of 30 kHz, which is outside the range of audiblefrequencies.

    4.2 Motor Rotation DirectionThe current-carrying order of the outputs depends onthe DIR pin state (Rotation Direction) and is describedin Table 4-1. The DIR pin is not designed for dynamicdirection change during operation.

    4.3 Frequency Generator FunctionThe Frequency Generator output (FG) is a Hall effectsensor equivalent digital output, giving information toan external controller about the speed and phase of themotor. The FG pin is an open drain output, connectingto a logical voltage level through an external pull-upresistor. When a lock or an out-of-sync situation isdetected by the driver, this output is set to high-impedance until the motor is restarted. Leave the pinopen when it is not used.

    4.4 Lockup Protection and Automatic Restart

    If the motor is blocked and cannot rotate freely, a lock-up protection circuit detects it and disables the driver bysetting its outputs to high-impedance to prevent themotor coil from burnout. After a waiting time (TWAIT),the lock-up protection is released and normal operationresumes for a given time (TRUN). If the motor is stillblocked, a new period of waiting time is started. TWAITand TRUN timings are fixed internally, so that noexternal capacitor is required.

    4.5 Overcurrent ProtectionThe motor peak current is limited by the driver to750 mA (standard value), thus limiting the maximumpower dissipation in the coils.

    4.6 Thermal ShutdownThe MTD6505 device has a thermal protection functionwhich detects when the die temperature exceedsTJ = +170C. When this temperature is reached, thecircuit enters the Thermal Shutdown mode, and theoutputs OUT1, OUT2 and OUT3 are disabled (high-impedance), avoiding the IC destruction and allowingthe circuit to cool down. When the junction temperature(TJ) drops below +145C, normal operation resumes.

    The thermal detection circuit has +25C hysteresis.

    FIGURE 4-1: Thermal Protection Hysteresis.

    Note 1: The PWM frequency has no direct effecton the motor speed and is asynchronouswith the activation of the outputtransistors.

    Note 2: The standard output frequency is 30 kHz.A 20 kHz output frequency option isavailable upon request.

    TABLE 4-1: MOTOR ROTATION DIRECTION OPTIONS (DIR PIN)

    DIR Pin State RotationDirectionOutputs Activation

    Sequence

    Connected to GND or Floating

    Forward OUT1 OUT2 OUT3

    Connected to VBIAS

    Reverse OUT3 OUT2 OUT1

    TJ+145

    Thermal shutdown

    +170

    Normal operation

    2011-2013 Microchip Technology Inc. DS20002281B-page 11

  • MTD6505

    4.7 Internal Voltage RegulatorVBIAS voltage is generated internally and is used tosupply internal logical blocks. The VBIAS pin is used toconnect an external decoupling capacitor (1 F orhigher). Notice that this pin is for IC internal use, and isnot designed to supply DC current to external blocks.

    4.8 Back Electromotive Force (BEMF) Coefficient Setting

    KM is the electro-mechanical coupling coefficient of themotor (also referred to as motor constant or BEMFconstant). Depending on the conventions in use, theexact definition of KM and its measurement criteria canvary among motor manufacturers. To accommodatevarious motor applications, the MTD6505 providesoptions to facilitate diverse BEMF coefficients.

    The MTD6505 defines BEMF coefficient (KM) as thepeak value of the phase-to-phase BEMF voltage,normalized to the electrical speed of the motor. Thefollowing table offers methods to set the KM value forthe MTD6505 device.

    The RPROG sensing is actually a sequence that iscontrolled by the firmware. For any given RPROG, theinternal control block will output the corresponding KMrange.

    4.9 Defining the Correct RPROG Value

    This section explains how to define the correct KMvalue for a specific fan. The KM is linked to the RPROG(see Table 4-2). An incorrect KM selection can createissues, or reduce the efficiency.

    4.9.1 OPERATION

    Follow the next steps to define the right RPROG value:

    1. Apply a constant stream of air to a fan that is notconnected.

    2. Using an oscilloscope, measure the waveformbetween two phases, when the fan is rotating.

    3. Measure the generated peak-to-peak voltage(Vp-p) value and the frequency (f).

    4. Compute KM based on the measured Vp-p andf (in mV/Hz):

    EQUATION 4-1: KM COMPUTE

    KM should be constant for all fan rotation speeds; but,for the KM measurement, the fan rotation speed (due tothe air stream) should be close to the nominal.

    TABLE 4-2: Km SETTINGS

    KM Option

    KM (mV/Hz) RangePhase-to-Phase RPROG

    Min Max

    KM0 3.25 6.5 GNDKM1 6.5 13 24 kKM2 13 26 3.9 kKM3 26 52 VBIAS

    Note: This is a theoretical procedure that doesnot take care of the harmonics generatedby the BEMF. This information has to betaken for indication only.

    KMVp p2f-------------=

    DS20002281B-page 12 2011-2013 Microchip Technology Inc.

  • MTD6505

    5.0 PACKAGING INFORMATION

    5.1 Package Marking Information

    Device Code

    MTD6505T-E/NA AAAD

    10-Lead UDFN (3x3x0.5 mm) Example

    AAAD1315256

    Legend: XX...X Customer-specific informationY Year code (last digit of calendar year)YY Year code (last 2 digits of calendar year)WW Week code (week of January 1 is week 01)NNN Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn)* This package is Pb-free. The Pb-free JEDEC designator ( )

    can be found on the outer packaging for this package.

    Note: In the event the full Microchip part number cannot be marked on one line, it will be carried overto the next line, thus limiting the number of available characters for customer-specificinformation.

    3e

    3e

    2011-2013 Microchip Technology Inc. DS20002281B-page 13

  • MTD6505

    DS20002281B-page 14 2011-2013 Microchip Technology Inc.

  • MTD6505

    2011-2013 Microchip Technology Inc. DS20002281B-page 15

  • MTD6505

    DS20002281B-page 16 2011-2013 Microchip Technology Inc.

  • MTD6505

    APPENDIX A: REVISION HISTORY

    Revision B (October 2013)The following is the list of modifications:

    1. Updated the Absolute Maximum Ratingssection with the correct VBIAS parameter.

    2. Updated the Thermal Resistance values in theTemperature Specifications table.

    3. Added Figure 2-11 and Figure 2-12.4. Added Section 4.9 Defining the Correct

    RPROG Value.5. Minor grammatical and editorial corrections.

    Revision A (November 2011)This is the original release of this document.

    2011-2013 Microchip Technology Inc. DS20002281B-page 17

  • MTD6505

    NOTES:

    DS20002281B-page 18 2011-2013 Microchip Technology Inc.

  • MTD6505

    PRODUCT IDENTIFICATION SYSTEMTo order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.

    Device: MTD6505T: 3-Phase Brushless DC, Sinusoidal Sensorless

    Fan Motor Driver (Tape and Reel)

    Temperature Range: E = Extended -40C to +125C

    Package: NA = Plastic Dual Flat, thermally-enhanced, 3x3x0.5 mm Body (UDFN)

    Examples:a) MTD6505T-E/NA Tape and Reel,

    Extended Temperature10LD UDFN Package

    PART NO. T -X /XX

    PackageTemperatureTape & ReelDevice

    2011-2013 Microchip Technology Inc. DS20002281B-page 19

  • MTD6505

    NOTES:

    DS20002281B-page 20 2011-2013 Microchip Technology Inc.

  • Note the following details of the code protection feature on Microchip devices: Microchip products meet the specification contained in their particular Microchip Data Sheet.

    Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions.

    There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchips Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

    Microchip is willing to work with the customer who is concerned about the integrity of their code.

    Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as unbreakable.

    Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of ourproducts. Attempts to break Microchips code protection feature may be a violation of the Digital Millennium Copyright Act. If such actsallow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

    Information contained in this publication regarding deviceapplications and the like is provided only for your convenienceand may be superseded by updates. It is your responsibility toensure that your application meets with your specifications.MICROCHIP MAKES NO REPRESENTATIONS ORWARRANTIES OF ANY KIND WHETHER EXPRESS ORIMPLIED, WRITTEN OR ORAL, STATUTORY OROTHERWISE, RELATED TO THE INFORMATION,INCLUDING BUT NOT LIMITED TO ITS CONDITION,QUALITY, PERFORMANCE, MERCHANTABILITY ORFITNESS FOR PURPOSE. Microchip disclaims all liabilityarising from this information and its use. Use of Microchipdevices in life support and/or safety applications is entirely atthe buyers risk, and the buyer agrees to defend, indemnify andhold harmless Microchip from any and all damages, claims,suits, or expenses resulting from such use. No licenses areconveyed, implicitly or otherwise, under any Microchipintellectual property rights.

    2011-2013 Microchip Technology Inc.

    QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV

    == ISO/TS 16949 ==

    Trademarks

    The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

    FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A.

    Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.

    Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

    SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.

    GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.

    All other trademarks mentioned herein are property of their respective companies.

    2011-2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.

    Printed on recycled paper.

    ISBN: 978-1-62077-533-2

    DS20002281B-page 21

    Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Companys quality system processes and procedures are for its PIC MCUs and dsPIC DSCs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchips quality system for the design and manufacture of development systems is ISO 9001:2000 certified.

  • DS20002281B-page 22 2011-2013 Microchip Technology Inc.

    AMERICASCorporate Office2355 West Chandler Blvd.Chandler, AZ 85224-6199Tel: 480-792-7200 Fax: 480-792-7277Technical Support: http://www.microchip.com/supportWeb Address: www.microchip.comAtlantaDuluth, GA Tel: 678-957-9614 Fax: 678-957-1455BostonWestborough, MA Tel: 774-760-0087 Fax: 774-760-0088ChicagoItasca, IL Tel: 630-285-0071 Fax: 630-285-0075ClevelandIndependence, OH Tel: 216-447-0464 Fax: 216-447-0643DallasAddison, TX Tel: 972-818-7423 Fax: 972-818-2924DetroitFarmington Hills, MI Tel: 248-538-2250Fax: 248-538-2260IndianapolisNoblesville, IN Tel: 317-773-8323Fax: 317-773-5453Los AngelesMission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608Santa ClaraSanta Clara, CA Tel: 408-961-6444Fax: 408-961-6445TorontoMississauga, Ontario, CanadaTel: 905-673-0699 Fax: 905-673-6509

    ASIA/PACIFICAsia Pacific OfficeSuites 3707-14, 37th FloorTower 6, The GatewayHarbour City, KowloonHong KongTel: 852-2401-1200Fax: 852-2401-3431Australia - SydneyTel: 61-2-9868-6733Fax: 61-2-9868-6755China - BeijingTel: 86-10-8569-7000 Fax: 86-10-8528-2104China - ChengduTel: 86-28-8665-5511Fax: 86-28-8665-7889China - ChongqingTel: 86-23-8980-9588Fax: 86-23-8980-9500China - HangzhouTel: 86-571-2819-3187 Fax: 86-571-2819-3189China - Hong Kong SARTel: 852-2943-5100 Fax: 852-2401-3431China - NanjingTel: 86-25-8473-2460Fax: 86-25-8473-2470China - QingdaoTel: 86-532-8502-7355Fax: 86-532-8502-7205China - ShanghaiTel: 86-21-5407-5533 Fax: 86-21-5407-5066China - ShenyangTel: 86-24-2334-2829Fax: 86-24-2334-2393China - ShenzhenTel: 86-755-8864-2200 Fax: 86-755-8203-1760China - WuhanTel: 86-27-5980-5300Fax: 86-27-5980-5118China - XianTel: 86-29-8833-7252Fax: 86-29-8833-7256China - XiamenTel: 86-592-2388138 Fax: 86-592-2388130China - ZhuhaiTel: 86-756-3210040 Fax: 86-756-3210049

    ASIA/PACIFICIndia - BangaloreTel: 91-80-3090-4444 Fax: 91-80-3090-4123India - New DelhiTel: 91-11-4160-8631Fax: 91-11-4160-8632India - PuneTel: 91-20-3019-1500Japan - OsakaTel: 81-6-6152-7160 Fax: 81-6-6152-9310Japan - TokyoTel: 81-3-6880- 3770 Fax: 81-3-6880-3771Korea - DaeguTel: 82-53-744-4301Fax: 82-53-744-4302Korea - SeoulTel: 82-2-554-7200Fax: 82-2-558-5932 or 82-2-558-5934Malaysia - Kuala LumpurTel: 60-3-6201-9857Fax: 60-3-6201-9859Malaysia - PenangTel: 60-4-227-8870Fax: 60-4-227-4068Philippines - ManilaTel: 63-2-634-9065Fax: 63-2-634-9069SingaporeTel: 65-6334-8870Fax: 65-6334-8850Taiwan - Hsin ChuTel: 886-3-5778-366Fax: 886-3-5770-955Taiwan - KaohsiungTel: 886-7-213-7828Fax: 886-7-330-9305Taiwan - TaipeiTel: 886-2-2508-8600 Fax: 886-2-2508-0102Thailand - BangkokTel: 66-2-694-1351Fax: 66-2-694-1350

    EUROPEAustria - WelsTel: 43-7242-2244-39Fax: 43-7242-2244-393Denmark - CopenhagenTel: 45-4450-2828 Fax: 45-4485-2829France - ParisTel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79Germany - MunichTel: 49-89-627-144-0 Fax: 49-89-627-144-44Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781Netherlands - DrunenTel: 31-416-690399 Fax: 31-416-690340Spain - MadridTel: 34-91-708-08-90Fax: 34-91-708-08-91UK - WokinghamTel: 44-118-921-5869Fax: 44-118-921-5820

    Worldwide Sales and Service

    08/20/13

    http://support.microchip.comhttp://www.microchip.com

    Sinusoidal Sensorless 3-Phase Brushless DC (BLDC) Fan Motor Driver1.0 Electrical Characteristics2.0 Typical Performance Curves3.0 Pin Descriptions4.0 Functional Description4.1 Speed Control4.2 Motor Rotation Direction4.3 Frequency Generator Function4.4 Lockup Protection and Automatic Restart4.5 Overcurrent Protection4.6 Thermal Shutdown4.7 Internal Voltage Regulator4.8 Back Electromotive Force (BEMF) Coefficient Setting4.9 Defining the Correct RPROG Value

    5.0 Packaging Information5.1 Package Marking Information

    Appendix A: Revision HistoryWorldwide Sales and Service