Personal Audio System No sound / Sound from only …store.sony.com.tw/resource/manual/SRS-BTX500.pdf · Personal Audio System ... SRS-BTX500 Function of Parts BATTERY/CHARGE indicator

Page 1

Personal Audio System

©2013 Sony Corporation Printed in China

4-457-527-41(1)

SRS-BTX500

Function of PartsBATTERY/CHARGE indicator Lights up, flashes or turns off depending on the status of the system.For details, see the following section, “Indications of BATTERY/CHARGE indicator.”

N-markTouch to make Bluetooth connection with an NFC compatible smartphone.

(call) buttonPress to call or operate during a call.

VOLUME −/+ buttonsAdjusts the volume.

Illumination lampLights up in a variety of colors depending on the status of the system. For details, see the following section, “Indications of Illumination lamp.”

MicrophoneUse during a call.

StandOpen to use the system.

DC IN 15V jackConnects the supplied AC adaptor.

AUDIO IN jackConnects to the headphone jack of a portable audio device,computer, etc., using a connecting cord (not supplied).

BLUETOOTH STANDBY switchTurns on and off the Bluetooth standby mode.

RESET buttonResets the system.

DC OUT ONLY connector (USB)Charges devices, such as your smartphone, etc. by connecting to the DC OUT ONLY connector (USB connector).

SOUND buttonPress to select a sound effect.

SOUND indicatorLights up, according to the sound effect setting.

AUDIO IN buttonPress to listen to sound from a device connected by a connecting cord (not supplied).

AUDIO IN indicator (amber)Lights up in AUDIO IN mode.

BLUETOOTH PAIRING buttonPress to pair with a Bluetooth device.

Bluetooth indicator (blue)Lights up, flashes or turns off depending on the communication status.For details, see the following section, “Indications of the Bluetooth function.”

/ buttonTurns the system on/off.

Indications of BATTERY/CHARGE indicator (built-in lithium-ion battery)

Status BATTERY/CHARGE indicator

System turned on Lights up (green) (battery operation only)

Battery requires charging Flashes (green)

Charging battery Lights up (amber)

Charging complete Off

Indications of Illumination lampStatus Illumination lamp

AUDIO IN mode Lights up (white)

Searching for a device Lights up (white)

Connecting to Bluetooth device

Lights up (blue)

Pressing VOLUME−/+ buttons

Flashes once (white)

When the volume hits the maximum or minimum

Flashes three times (white)

Tip To turn the illumination on/off, hold down the

BLUETOOTH PAIRING button, then press and hold the / button.

Indications of the Bluetooth functionStatus Bluetooth indicator (blue)

Pairing with a device Flashes quickly

Searching for a device Flashes

Connected to a device Lights up

Bluetooth standby mode Flashes slowly

Opening the StandThe system stands itself by opening the stand.

To close the standClose the stand to the opposite way of arrow.

Turning the System on and off/Charging the systemThis system can operate by AC adaptor or built-in lithium-ion battery (rechargeable). Charge the battery before using the system for the first time.

1 Connect the supplied AC adaptor.The BATTERY/CHARGE indicator (amber) lights up when the battery is being charged, and turns off when charging is complete. It takes approximately 4 hours to charge the battery.

2 Press the / button.

Tip You can operate the system by battery instead of the AC adaptor

by charging the system before use.

Notes When the BATTERY/CHARGE indicator flashes as below,

charge the system. In these cases, you cannot charge devices via the DC OUT ONLY connector.

Flashes (green) (Battery power is low).Flashes (amber), then turns off after turning on the system (No battery power remaining).

When you switch the power source between AC adaptor and battery by connecting/disconnecting the AC adaptor, the system stops sound output for a short while. This is not a malfunction.

The maximum power output will be lower when the AC adaptor is disconnected.

In an extremely cold or hot environment, note the following points.

When operating by the AC adaptor, charging may complete too quickly, or may not be possible.When operating on battery only, the system may stop after the BATTERY/CHARGE indicator flashes (green) three times.

Charge the battery at least twice a year. Repeated recharging causes the capacity of the battery to

decrease over time. When the battery life drops to half the usual time, even after a full charge, contact your nearest Sony dealer to replace the battery.

To reset the systemPress the RESET button on the rear of the system with a pointed object if the buttons on the system do not function.

How to Make Wireless Connection with Bluetooth DevicesYou can enjoy music and hands-free calling with the system wirelessly by using your device’s Bluetooth function.Choose one of the following three connection methods, best suited for the Bluetooth device. For details on how to operate your device, refer to the operating instructions supplied with the device.

Pairing with a Bluetooth device: see Pattern A

Bluetooth devices need to be “paired” with each other beforehand.

Connecting with a paired device: see Pattern B

To listen to music with a Bluetooth device that has been paired, see this pattern.

One touch connection with a smartphone (NFC):see Pattern C

Using an NFC compatible smartphone, you can establish a Bluetooth connection by just touching the system with it.

Check the following before operating the system. Both the system and the device are placed within 1 m of

each other. The system is connected to the AC adaptor, or the battery is

sufficiently charged. The operating instructions supplied with the device are at

hand.

Pattern A Pairing and connecting with a Bluetooth device1 Turn on the system.

The Bluetooth indicator (blue) flashes. If the AUDIO IN indicator (amber) lights up, press the BLUETOOTH PAIRING button.

2 Set the Bluetooth function of the Bluetooth device to on.For details, refer to the operating instructions supplied with the device.

––

–

–

Operating Instructions使用說明書

3 Press and hold the BLUETOOTH PAIRING button on the system until two beeps are heard.The Bluetooth indicator (blue) begins to flash quickly and pairing mode is entered.

Tip When the system is turned on first time, the Bluetooth

indicator (blue) starts flashing quickly.

Flashes quickly

4 Perform the pairing procedure on the Bluetooth device to detect the system.

5 Select “SRS-BTX500” shown in the display of the Bluetooth device.If “SRS- BTX500” does not appear on the device’s display, repeat from step 2.

Note Some devices cannot display a list of detected devices.

6 If Passcode* input is required on the display of the Bluetooth device, input “0000.”The Bluetooth connection is established and the Bluetooth indicator (blue) on the system stays on.* Passcode may be called “Passkey,” “PIN code,” “PIN number,” or “Password.”

Tip To pair with other Bluetooth devices, repeat steps 2 to 6 for each

device.

Notes Pairing mode of the system is cancelled after about 5 minutes,

and the Bluetooth indicator (blue) flashes. If the pairing mode is cancelled while performing this procedure, start over from step 3.

Passcode of the system is fixed as “0000.” The system cannot be paired with a Bluetooth device whose Passcode is not “0000.”

Once Bluetooth devices are paired, there is no need to pair those devices again. However, in the following case, you will need to perform the pairing procedure again.

The system is paired with 9 or more devices. The system can be paired with up to 8 Bluetooth devices. If a new device is paired after 8 devices have been paired, the device whose latest connection time is the oldest among the 8 paired devices is replaced by the new one.

More than one device can be paired with the system, but sound will be heard from just one of those devices.

Pattern B Connecting with a paired Bluetooth device1 Turn on the system.

The Bluetooth indicator (blue) flashes. If the AUDIO IN indicator (amber) lights up, press the BLUETOOTH PAIRING button.

2 Set the Bluetooth function of the Bluetooth device to on.

Tip In the case of the last-connected Bluetooth device, the

system tries to re-establish Bluetooth connection with it if the device’s Bluetooth function is on. When Bluetooth connection is established, the Bluetooth indicator (blue) on the system stays on.

3 Select “SRS-BTX500” shown in the display of the Bluetooth device.If necessary, select a Bluetooth profile that the system supports from the following: A2DP, HSP or HFP. For details on each profile, see “What is Bluetooth Wireless Technology?”The Bluetooth connection is established and the Bluetooth indicator (blue) on the system stays on.

Notes This step may not be necessary for some devices. If the system cannot connect to the Bluetooth device, delete

“SRS-BTX500” from the Bluetooth device, then perform pairing again.

Bluetooth standby modeWhen the Bluetooth standby mode is set to ON, the system can be turned on and operated by a Bluetooth device.

Note If the system is being powered by battery, even if the

system is turned off, battery power will continue to be consumed if the BLUETOOTH STANDBY switch is set to ON.

Pattern C Connecting with a smartphone by One touch (NFC)By just touching the system with an NFC compatible smartphone, the system is turned on automatically and then paired and connected with the smartphone.

1 Download and install the app “NFC Easy Connect” on the smartphone.“NFC Easy Connect” is an original app by Sony for Android phones, and is available at Google Play Store. Search for “NFC Easy Connect” or scan the following two-dimensional code to download and install the free app. Communication fees are required to download the app.The app may not be downloadable in some country/regions.

Tip For some smartphones, One touch connection may be

available without downloading the app “NFC Easy Connect.” In that case, the operation and specifications may be different from the description here. For details, refer to the operating instructions supplied with the smartphone.

By the two-dimensional code: Use a two-dimensional code reader app.

Compatible smartphones Smartphones with the NFC function built-in

(OS: Android 2.3.3 or later, excluding Android 3.x)

About NFCNFC (Near Field Communication) is a technology enabling short-range wireless communication between various devices, such as mobile phones and IC tags. Thanks to the NFC function, data communication can be achieved easily just by touching the relevant symbol or designated location on NFC compatible devices.

2 Start the app “NFC Easy Connect” on the smartphone.Make sure that the application screen is displayed.

3 Touch the system with the smartphone.Keep touching the smartphone on the N marked part of the system until the smartphone vibrates.

Smartphone vibrates (system recognized)

Follow the on-screen instructions to establish the connection.

–

DC IN 15V jack

AUDIO IN jack BLUETOOTH STANDBY switch

RESET button

DC OUT ONLY connector (USB)

When the Bluetooth connection is established, the Bluetooth indicator (blue) stays on.

Tips If it is difficult to establish the connection, try the following.

Activate the app “NFC Easy Connect” and move the smartphone slightly on the N marked part of the system.If the smartphone is in a case, remove it.

Touch the system with the smartphone again to disconnect. If you have multiple NFC compatible devices, just touch the

smartphone to a different device to switch the connection to that device. For example, when your smartphone is connected with NFC compatible headphones, just touch the smartphone to the system to change the Bluetooth connection to the system (One touch connection switching).

Listening to MusicYou can enjoy music wirelessly, via the Bluetooth function built in your devices.

Operations may vary depending on the Bluetooth device. Refer also to the operating instructions supplied with your Bluetooth device.

1 Make the Bluetooth connection between the system and the device.For details on the Bluetooth connection procedure, see “How to Make Wireless Connection with Bluetooth Devices.” When the Bluetooth connection is established, the Bluetooth indicator (blue) on the system stays on.

2 Start playback on the Bluetooth device, then adjust the volume.Set the volume of the Bluetooth device to a moderate level, and press the VOLUME –/+ buttons on the system.

Auto power offThe system automatically turns off after about 20 minutes when the hands-free is not being used (the system is not connected with a Bluetooth device via HFP/HSP), and when no device is being charged via the DC OUT ONLY connector, and when no music is being played.

After useDo any of the following. Set the Bluetooth function of the Bluetooth device off. For

details, refer to the operating instructions supplied with the device.

Turn off the Bluetooth device. Turn off the system. Touch the system with the smartphone again to disconnect

(NFC compatible smartphones only).

Using Hands-free Calling While Listening to MusicYou can enjoy hands-free calling via Bluetooth connection with a Bluetooth mobile phone that has a music function and supports the Bluetooth profile A2DP, and HFP or HSP.If your Bluetooth mobile phone supports both HFP and HSP, set to HFP.

Operations may vary depending on the Bluetooth mobile phone. Refer also to the operating instructions supplied with your mobile phone.

1 Make the Bluetooth connection between the system and the mobile phone.For details on the Bluetooth connection procedure, see “How to Make Wireless Connection with Bluetooth Devices.” When the Bluetooth connection is established, the Bluetooth indicator (blue) on the system stays on.

2 Start playback on the Bluetooth mobile phone, then adjust the volume.Set the volume of the Bluetooth mobile phone to a moderate level, and press the VOLUME –/+ buttons on the system.

To callOperate the Bluetooth mobile phone. Check that a dialing tone is heard on the system and talk using the microphone. If no dialing tone is heard, press the (call) button on the system for about 2 seconds to change the call device to the system.

To receive a callWhen an incoming call arrives, the playback pauses and a ring tone is heard from the system. Press the (call) button on the system and talk using the microphone.

Tips If no ring tone is heard from the system when incoming call

arrives, stop playback and press the (call) button to talk. You can use the hands-free calling when playback is completed. During a call, press the VOLUME –/+ buttons on the system to

adjust the volume.

Notes The sound is output from the left speaker only during a call. Use your smartphone at least 50 cm from the system. Noise may

result if the system and smartphone are too close.

To end a callPress the (call) button. If you were listening to music when the call arrived, it will be resumed when the call has finished.

After useDo any of the following. Set the Bluetooth function of the Bluetooth device off. For

details, refer to the operating instructions supplied with the device.

Turn off the Bluetooth device. Turn off the system. Touch the system with the smartphone again to disconnect

(NFC compatible smartphones only).

Unit button functions during a callAvailable functions may vary depending on the Bluetooth mobile phone, or the profiles supported by the Bluetooth mobile phone. Refer to the operating instructions supplied with the Bluetooth mobile phone.

Status (call) button

Standby Press once to start voice dial (voice dial compatible mobile phones only).

Press for about 2 seconds to redial the phone number that is dialed last time.

Outgoing call

Press once to cancel outgoing call. Press for about 2 seconds to change call

device between the system and mobile phone.

Incoming call

Press once to answer call. Press for about 2 seconds to reject call.

During call

Press once to finish call. Press for about 2 seconds to change call

device between the system and mobile phone.

Using Hands-free calling with another Bluetooth mobile phone while listening to musicThis system is compatible with Multipoint technology, which allows you to enjoy hands-free calling while listening to music from a Bluetoothcompatible music player.

One touch connection (NFC) cannot be used in this procedure.

Operations may vary depending on the Bluetooth device. This type of Bluetooth connection may not be established depending on the combination of the Bluetooth devices. Refer also to the operating instructions supplied with your Bluetooth devices.

–

–

N-mark

BATTERY/CHARGE indicator

VOLUME −/+ buttons

(call) button

SOUND button/indicator

AUDIO IN button/indicator

BLUETOOTH -PAIRING button

Bluetooth indicator

/ button

Illumination lamp Microphone

1 Make the Bluetooth connections between the system and a Bluetooth music player via A2DP, and between the system and a Bluetooth mobile phone via HFP or HSP.For details on the Bluetooth connection procedure, see “How to Make Wireless Connection with Bluetooth Devices.” When the Bluetooth connection is established, the Bluetooth indicator (blue) on the system stays on.

Tips To use only the calling function of a Bluetooth mobile phone

that also has a music function, establish Bluetooth connection between the system and the mobile phone via HFP or HSP, not via A2DP.

Depending on the Bluetooth mobile phone, while the Bluetooth connection is established via HFP or HSP, the other Bluetooth connection via A2DP may also be occupied by the same Bluetooth mobile phone. A Bluetooth music player cannot be connected with this system in this case.

Note To make the same connection with the same devices after

turning the system off, follow this procedure again.

To Enjoy the Sound Effect SettingYou can enjoy sound effects as desired.

1 Press the SOUND button to select the sound effect.The SOUND indicator (see below) shows the current sound effect setting.You can switch between effects by repeatedly pressing the SOUND button.

Status Sound effect

Amber High-quality bass sound will be heard (MEGA BASS). This setting is enabled by default when you first turn on the system.

Green Surround sound will be heard (MEGA BASS+SURROUND).

Off The sound effect is off.

Tip The system remembers the last sound effect setting next time it

is turned on.

Listening to Music by Wired Connection with a Portable Audio Device, etc.1 Connect the device to the system.

Connecting cord (not supplied)

(Stereo mini jack)

2 Turn on the system.

3 Turn on the connected device.

4 Press the AUDIO IN button on the system.

5 Operate the connected device.Set the volume of the connected device to a moderate level, then press the VOLUME –/+ buttons on the system.

Notes You cannot play music only by connecting to the system with

the connecting cord. Make sure to also press the AUDIO IN button.

Hands-free calling is not available while you are listening to music from a device connecting to the system by the connected cord.

Auto power off The system automatically turns off after about 20 minutes when the hands-free is not being used (the system is not connected with a Bluetooth device via HFP/HSP), and when no device is being charged via the DC OUT ONLY connector, and when no music is being played.

Charging USB Devices, such as Smartphones, via a USB Connection to the SystemYou can charge your smartphone by connecting to the DC OUT ONLY connector (USB) of the system. When using the system by the built-in battery only, you can also charge a smartphone from the battery of the system. Turn on the system in order to charge a USB device.

USB cable(not supplied)

Note This function is not for data communication by USB cable.

Disposing of the SystemFor environment protection, remove the built-in lithium-ion battery pack from the system.Before removing the battery, drain the battery by removing the AC adaptor and using the system only with the battery.

Take out the lithium-ion battery for recycling. Do not open the cabinet other than when disposing of the system.

1 Turn off the system and remove the AC adaptor.

2 Detach the cover of the rear of the system to remove the battery pack.Open the stand.Remove the 4 rubber covers from the bottom of the

system.Remove the 4 screws.Remove the cover.Remove the connector plug from the system.Remove the battery.

Note Be careful not to damage the code cover with metallic tweezers,

etc. when you remove the battery pack from the system.

SpecificationsSpeaker sectionSpeaker system Satellite speaker:

Approx. 48 mm dia. × 2 Subwoofer:

Approx. 80 mm dia. × 1Enclosure type Satellite speaker: Sealed enclosure Subwoofer: Passive radiator model

Amplifier sectionReference output power

Using AC adaptor: 10 W + 10 W (Satellite speaker, at 1% harmonic distortion, 1 kHz, 6 Ω), 20 W (Subwoofer, at 1% harmonic distortion, 100 Hz, 4 Ω)

Using battery: 4 W + 4 W (Satellite speaker, at 10% harmonic distortion, 1 kHz, 6 Ω), 8 W (Subwoofer, at 10% harmonic distortion, 100 Hz, 4 Ω)

BluetoothCommunication System

Bluetooth Specification version 3.0Output Bluetooth Specification Power Class 2Maximum communication range

Line of sight approx. 10 m*1

Frequency band 2.4 GHz band (2.4000 GHz - 2.4835 GHz)Modulation method

FHSSCompatible Bluetooth Profiles*2

A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) HSP (Headset Profile) HFP (Hands-free Profile)

Supported Codec*3 SBC*4, AAC*5

Transmission range (A2DP) 20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)

*1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, aerial’s performance, operating system, software application, etc.

*2 Bluetooth standard profiles indicate the purpose of Bluetooth communication between devices.

*3 Codec: Audio signal compression and conversion format*4 Subband Codec*5 Advanced Audio Coding

MicrophoneType: Electret condenserDirectional characteristic:

Omni directionalEffective frequency range:

50 Hz -10 kHz

GeneralInput AUDIO IN jack (ø 3.5 mm stereo mini jack)DC OUT USB jack Type A (for charging the battery

of a connected device) (5 V, Max.1.5 A)Power DC 15 V (using the supplied AC adaptor

connected to AC 100 V - 240 V, 50 Hz/60 Hz power supply) or, using built-in lithium-ion battery

Usage life of lithium-ion battery (using the Bluetooth connection) approx. 6 hours*6

Dimensions (including projecting parts and controls) Approx. 385.0 mm × 152.0 mm × 65.0 mm

(w/h/d)Mass Approx. 2,000 g including batterySupplied accessories

AC adaptor (AC-E1530) (1) Operating Instructions (this document) (1) Bluetooth® Startup Guide (1)

Carrying case (1)*6 Time may vary, depending on the temperature or

conditions of use.

Design and specifications are subject to change without notice.

Troubleshooting

No sound / Sound from only one speaker / Low sound level

Check that both this system and the connected device are turned on.

If you are connecting a personal computer to the system, make sure the audio output setting of the computer is set for a Bluetooth device.

Turn up the volume of the system and the connected device.

Pair this system and the Bluetooth device again.

Check that the connected device is being played back.

If the connected device is monaural, sound will only be output from the left speaker.

Check that both plugs of the connecting cord (not supplied) are firmly inserted into the system and the connected device.

Distorted sound / Humming or noise in the system output

Turn down the volume of the connected device.

Keep the system away from a TV.

If the connected device has an equalizer function, set it to off.

Switch the Bluetooth connection to A2DP by operating the Bluetooth device when HFP or HSP is set.

Keep the system away from a microwave oven, wireless LAN, etc.

If you connect a device with a built-in radio or tuner to this system, broadcasts may not be received, or sensitivity may be reduced. Locate the system farther away from the device and check that you can listen to the broadcasts satisfactorily.

Bring this system and the Bluetooth device closer together. Remove any obstacle between this system and the Bluetooth device.

Charge the system by connecting the AC adaptor if the BATTERY/CHARGE indicator flashes in green.

Pairing is not possible

Bring this system and the Bluetooth device to within 1 m of each other.

If the Bluetooth indicator (blue) is not flashing quickly, press and hold the BLUETOOTH PAIRING button on the system until two beeps are heard.

No voice / Low voice from recipient

Check that both this system and the connected device are turned on.

Select HFP or HSP Bluetooth connection by operating the Bluetooth device.

Check that output of the Bluetooth mobile phone is set for the system.

Turn up the volume of the system and the connected device.

One touch connection (NFC) is not possible

Keep the smartphone close to the system until the smartphone vibrates. If you fail, move the smartphone slightly on the N marked part of the system.

If the smartphone is in a case, remove it.

Check that the NFC function of the smartphone is set to on.

NFC receiving sensitivity depends on the device. If you fail to connect with a smartphone by One touch several times, connect to the system by on-screen operation.

Check that the “NFC Easy Connect” app is displayed on the smartphone.

Stand

Lights up

English Personal Audio System

Before operating the system, please read this guide thoroughly and retain it for future reference.

WARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And do not place lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or batteries installed) to excessive heat such as sunshine, fire or the like for a long time.

As the main plug of AC adaptor is used to disconnect the AC adaptor from the mains, connect it to an easily accessible AC outlet. Should you notice an abnormality in it, disconnect it from the AC outlet immediately.

The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

The nameplate and important information concerning safety are located on the bottom exterior of the main unit and on the surface of the AC adaptor.

On Copyrights and LicensesThe Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.Android is a trademark of Google Inc.iPhone is a trademark of Apple Inc., registered in the U.S. and other countries. Other trademarks and trade names are those of their respective owners.

PrecautionsNotes when using with a mobile phone For details on operation of your mobile phone when

receiving a telephone call while transmitting the sound using the Bluetooth connection, refer to the operating instructions supplied with the mobile phone.

Notes on the AC adaptor When connecting or disconnecting the AC adaptor, turn off

the system beforehand. Otherwise, it may cause malfunction.

Use only the supplied AC adaptor. To avoid damaging the system, do not use any other AC adaptor.

Polarity of the plug

Plug the AC adaptor into a nearby wall outlet (mains). In the case of a problem, unplug it from the wall outlet (mains) immediately.

Do not install the AC adaptor in a confined space, such as a bookcase or built-in cabinet.

To reduce the risk of fire or electric shock, do not expose the AC adaptor to dripping or splashing, and do not place objects filled with liquids, such as vases, on the AC adaptor.

On placement Do not set the speaker in an inclined position. Do not leave the system in a location near heat sources, or

in a place subject to direct sunlight, excessive dust, moisture, rain or mechanical shock.

On operation Do not insert any small objects, etc., into the jacks or

ventilation hole on the rear of the system. The system may short out or malfunction.

On cleaning Do not use alcohol, benzine, or thinner to clean the cabinet.

Others If you have any questions or problems concerning this

system that are not covered in this manual, please consult your nearest Sony dealer.

What is Bluetooth Wireless Technology?Bluetooth wireless technology is a short-range wireless technology that enables wireless data communication between digital devices, such as a computer and digital camera. Bluetooth wireless technology operates within a range of about 10 m.Connecting two devices as necessary is common, but some devices can be connected to multiple devices at the same time.You do not need to use a cable for connection, nor is it necessary for the devices to face one another, such is the case with infrared technology. For example, you can use such a device in a bag or pocket.Bluetooth standard is an international standard supported by thousands of companies all over the world, and employed by various companies worldwide.

Communication system and compatible Bluetooth profiles of the systemProfile is standardisation of the function for each Bluetooth device specification. The system supports the following Bluetooth version and profiles:Communication System:Bluetooth Specification version 3.0Compatible Bluetooth Profiles:

A2DP (Advanced Audio Distribution Profile): Transmitting or receiving audio content of high-quality.AVRCP (Audio Video Remote Control Profile): Controlling the volume.HSP (Headset Profile): Talking on the phone/Operating the phone.HFP (Hands-free Profile): Talking on the phone/Operating the phone by hands-free.

Maximum communication rangeUse Bluetooth devices within 10 m (line of sight) of the system.Maximum communication range may shorten under the following conditions.

There is an obstacle such as a person, metal, or wall between the system and Bluetooth device.A wireless LAN device is in use near the system.A microwave oven is in use near the system.A device that generates electromagnetic radiation is in use near the system.

Interference from other devicesBecause Bluetooth devices and wireless LAN (IEEE802.11b/g) use the same frequency, microwave interference may occur and resulting in communication speed deterioration, noise, or invalid connection if the system is used near a wireless LAN device. In such a case, perform the following.

Use the system at least 10 m away from the wireless LAN device.If the system is used within 10 m of a wireless LAN device, turn off the wireless LAN device.

Interference to other devicesMicrowaves emitting from a Bluetooth device may affect the operation of electronic medical devices. Turn off the system and other Bluetooth devices in the following locations, as it may cause an accident.

where inflammable gas is present, in a hospital, train, airplane, or a gas stationnear automatic doors or a fire alarm

Notes To be able to use the Bluetooth function, the Bluetooth

device to be connected requires the same profile as the system’s. Note also that even if the same profile exists, devices may vary in function depending on their specifications.

Due to the characteristic of Bluetooth wireless technology, the sound played on the system is slightly delayed from the sound played on the Bluetooth device during talking on the telephone or listening to the music.

This system supports security capabilities that comply with the Bluetooth standard to provide a secure connection when the Bluetooth wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using Bluetooth wireless technology.

We do not take any responsibility for the leakage of information during Bluetooth communication.

A device featuring the Bluetooth function is required to conform to the Bluetooth standard specified by Bluetooth SIG, and be authenticated. Even if the connected device conforms to the above mentioned Bluetooth standard, some devices may not be connected or work correctly, depending on the features or specifications of the device.

Noise or sound skips may occur depending on the Bluetooth device connected with the system, the communication environment or the usage environment.

–

–

–

–

–

–––

–

–

–

–

Page 2

零件的功能BATTERY/CHARGE指示燈 依據系統狀態而亮起、閃爍或熄滅。如需詳細資訊，請參閱下列章節：“BATTERY/CHARGE指示燈的指示”。

N標記觸碰即能建立和NFC相容智慧型手機的Bluetooth連線。

（撥打電話）按鈕按下以撥打電話，或在通話時進行操作。

VOLUME −/+按鈕調整音量。

照明燈依據系統狀態以多種色彩亮起。如需詳細資訊，請參閱下列章節：“照明燈的指示”。

麥克風在通話時使用。

支架打開以使用系統。

DC IN 15V插孔連接隨附的交流轉接器。

AUDIO IN插孔使用連接線（未隨附）連接可攜式音訊裝置、電腦等的耳機插孔。

BLUETOOTH STANDBY開關開啟和關閉Bluetooth待機模式。

RESET按鈕重設系統。

DC OUT ONLY連接器（USB）將智慧型手機等連接DC OUT ONLY連接器（USB連接器），就能為裝置充電。

SOUND按鈕按下以選擇音效。

SOUND指示燈依據音效設定而亮起。

AUDIO IN按鈕按下以聆聽使用連接線（未隨附）連接的裝置發出的聲音。

AUDIO IN指示燈（黃褐色）在AUDIO IN模式中亮起。

BLUETOOTH PAIRING按鈕按下以配對Bluetooth裝置。

Bluetooth指示燈（藍色）依據通訊狀態而亮起、閃爍或熄滅。如需詳細資訊，請參閱下列章節“Bluetooth功能的指示”。

/按鈕開啟/關閉系統電源。

BATTERY/CHARGE指示燈的指示（內建鋰離子電池）

狀態 BATTERY/CHARGE指示燈

系統電源開啟 亮起（綠色）（僅適用於電池操作）

電池需要充電 閃爍（綠色）

將電池充電 亮起（黃褐色）

充電完成 熄滅

照明燈的指示

狀態 照明燈

AUDIO IN模式 亮起（白色）

正在搜尋裝置 亮起（白色）

連線至Bluetooth裝置 亮起（藍色）

按下VOLUME−/+按鈕 閃爍1次（白色）

音量到達最大或最小時 閃爍3次（白色）

提示 若要開啟/關閉照明，請按住BLUETOOTH PAIRING按鈕，然

後按住/按鈕。

Bluetooth功能的指示

狀態 Bluetooth指示燈（藍色）

正與裝置配對 快速閃爍

正在搜尋裝置 閃爍

已連接裝置 亮起

Bluetooth待機模式 緩慢閃爍

打開支架系統打開支架後即可直立。

若要關閉支架朝箭頭相反方向關閉支架。

開啟和關閉系統電源/將系統充電本系統能以交流轉接器或內建的鋰離子電池（可充式）操作。首次使用系統之前請將電池充電。

1 連接隨附的交流轉接器。在電池充電時，BATTERY/CHARGE指示燈（黃褐色）會亮起，充電完成後則會熄滅。電池充電時間約需4小時。

2 按下/按鈕。

提示 在使用前將系統充電，就能以電池而非交流轉接器來操作系

統。

附註 BATTERY/CHARGE指示燈以下列方式閃爍時，請將系統充

電。在這些狀況下，您無法透過DC OUT ONLY連接器將裝置充電。

閃爍（綠色）（電池電量偏低）。閃爍（黃褐色），開啟系統電源之後熄滅（電池沒有剩餘電量）。

您以連接/中斷交流轉接器的方式，在交流轉接器和電池之間切換電源時，系統會停止輸出聲音一會兒。這不是故障。

中斷連接交流轉接器時，最大功率輸出會降低。 在極冷和極熱的環境中，請注意下列要點。

以交流轉接器操作時，充電可能會太快完成，或可能無法充電。僅以電池操作時，系統在BATTERY/CHARGE指示燈（綠色）閃爍3次之後可能會停止。

每年將電池充電至少2次。 重複充電會使電池的容電量隨時間降低。如果電池即使

在完全充電之後使用壽命減為正常時間之半，請就近聯絡Sony經銷商以更換電池。

若要重設系統如果系統上的按鈕沒有作用，請以尖銳的物體按下系統背面上的RESET按鈕。

如何與Bluetooth裝置建立無線連線使用裝置的Bluetooth功能可以透過無線方式，用系統欣賞音樂和進行免持通話。在下列3種連接方式中選擇最適合Bluetooth裝置的一種。如需關於如何操作裝置的詳細資訊，請參閱裝置隨附的操作指示。

與Bluetooth裝置配對：請參閱 類型A

Bluetooth裝置必須事先彼此“配對”。

連接已配對的裝置：請參閱 類型B

若要以已配對的Bluetooth裝置聆聽音樂，請參閱這個模式。

單觸連接智慧型手機（NFC）：請參閱 類型C

使用NFC相容智慧型手機，只需要以手機觸碰系統就能建立Bluetooth連線。

操作系統前請檢查下列項目。 系統和裝置彼此相距1公尺內。 系統已連接交流轉接器，或電池已充分充電。 裝置隨附的使用說明書保存在便利取得之處。

類型A 配對和連接Bluetooth裝置

1 開啟系統電源。Bluetooth指示燈（藍色）閃爍。 如果AUDIO IN指示燈（黃褐色）亮起，請按下BLUETOOTH PAIRING按鈕。

2 開啟Bluetooth裝置的Bluetooth功能。如需詳細資訊，請參閱裝置隨附的操作指示。

3 按住系統上的BLUETOOTH PAIRING按鈕，直到聽到兩聲嗶聲。Bluetooth指示燈（藍色）開始快速閃爍，並進入配對模式。

提示 首次開啟系統電源時，Bluetooth指示燈（藍色）開始快

速閃爍。

快速閃爍

––

–

–

繁體中⽂ 個人音響系統（無線喇叭）

操作系統前，請徹底閱讀本指南，並保留以供未來參考。

警告為防火災或觸電危險，切勿讓機器暴露於雨中或潮濕處。為降低火災的風險，請勿以報紙、桌布、窗簾等覆蓋裝置通風口。而且勿將點燃的蠟燭置於裝置上。

為降低火災或電擊的風險，請勿將本裝置暴露於水滴或潑濺之下，而且勿將充滿液體的物品，例如花瓶置於裝置上。

別把機器安裝在諸如書櫥等密閉處。

請勿讓電池（安裝的電池組或電池）長時間暴露在過熱的環境中，例如：陽光、火源等。

因為交流電源供應器的電源插頭用於從電源中斷交流電源供應器的連接，所以請將本機連接容易觸及的交流插座。如果您發現本機有異常，請立即從交流插座拔出電源插頭。

即使已經關閉播放機本身的電源，只要交流電源供應器仍連接至牆上供電插座，播放機並未中斷交流電源（總電源）。

铭牌和關於安全性的重要資訊位於主機的底部和交流電源供應器的表面上。

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

產品名稱：個⼈⾳響系統（無線喇叭）型 號：SRS-BTX500額定電壓：DC15V/輸⼊電流：3A機器號碼：如機體上標⽰產 地：中國⼤陸製造廠商：索尼公司進 ⼝ 商：台灣索尼股份有限公司地 址：104台北市⾧春路145號5樓製造年份：2013年電話：4499111

關於著作權和授權Bluetooth®文字標記和商標為Bluetooth SIG, Inc.所擁有，Sony Corporation對於該標誌的任何用途皆獲得授權。 N字標示為NFC Forum, Inc.在美國和其他國家的商標或註冊商標。Android為Google Inc.的商標。 iPhone是蘋果公司在美國和其他國家註冊的商標。 其他商標和商標名稱為其個別所有人所有。

防護措施

配合行動電話使用的注意事項 如需以Bluetooth連線發送聲音時，接聽來電時如何操作

行動電話的詳細資訊，請參閱行動電話隨附的操作指示。

交流電源供應器的注意事項 連接或中斷交流電源供應器時，請先關閉系統電源。否

則，可能造成故障。 請僅使用隨附的交流電源供應器。為避免損壞系統，請

勿使用任何其他交流電源供應器。

插頭極性

將交流電源供應器插入鄰近的牆壁插座。如果發生問題，請立即從牆壁插座拔出插頭。

請勿在受限的空間中安裝交流電源供應器，例如書櫃或嵌入式櫥櫃。

為降低火災或電擊的風險，請勿將交流電源供應器暴露於水滴或潑濺之下，而且勿將充滿液體的物品，例如花瓶置於交流電源供應器上。

關於放置的位置 請勿將揚聲器置於傾斜的位置。 請勿將系統置於接近熱源之處，或遭受直接日照、過多

灰塵、濕氣、雨水，或機械震動之處。

關於操作 請勿將任何小物件等插入到系統背面的插孔或通風孔

中。否則系統可能短路或故障。

關於清潔 請勿使用酒精、汽油或稀釋劑以清潔機殼。

其他 如果您有本手冊未涵蓋的系統疑問或問題，請諮詢最近

的Sony經銷商。

何謂Bluetooth無線技術？Bluetooth無線技術是一項短距離的無線技術，能進行數位裝置之間的無線資料通訊；例如電腦和數位相機。Bluetooth無線技術的操作範圍大約為10公尺。通常連接兩個必要裝置，但是某些裝置能同時連接到多個裝置。您不需要連接線進行連接，也不像紅外線技術必須裝置彼此面對。例如，您可在袋子或口袋中使用這種裝置。Bluetooth標準是全球數千家公司支援的國際標準，並由世界各公司部署採用。

系統的通訊系統和相容Bluetooth設定檔設定檔是每一Bluetooth裝置規格的功能標準化。系統支援下列Bluetooth版本和設定檔：通訊系統：Bluetooth規格版本3.0相容Bluetooth設定檔：

A2DP（進階播音設定檔）：傳送或接收高品質的音訊內容。AVRCP（音訊/視訊遠端控制設定檔）：控制音量。HSP（耳機設定檔）：在電話上通話/操作電話。HFP（免持設定檔）：以免持方式在電話上通話/操作電話。

最大通訊距離請在距離系統10公尺（視線）內使用Bluetooth裝置。最大通訊距離在下列狀況下可能會縮短。

系統和Bluetooth裝置之間有障礙物，例如人、金屬或牆壁。在系統附近使用無線LAN裝置。在系統附近使用微波爐。在系統附近使用會產生電磁輻射的裝置。

來自於其他裝置的干擾因為Bluetooth裝置和無線LAN（IEEE802.11b/g）採用相同頻率，如果在無線LAN裝置附近使用系統，可能發生微波干擾，或導致通訊速度變慢、雜訊，或連線失效。在此狀況下，請執行下列操作。

在距離無線LAN裝置至少10公尺處使用系統。如果在距離無線LAN裝置10公尺內使用系統，請關閉無線LAN裝置。

對於其他裝置的干擾Bluetooth裝置放射的微波可能會影響電子醫療裝置的操作。請關閉下列位置內的系統和其他Bluetooth裝置，因為可能導致意外事故。

在具有可燃氣體之處；在醫院、火車、飛機或加油站內靠近自動門或火災警報器之處

附註 若要能使用Bluetooth功能，要連接的Bluetooth裝置需

要有和系統相同的設定檔。 另請注意，即使有相同的設定檔，取決於裝置規格，裝置的功能可能不同。

由於Bluetooth無線技術的特性，在講電話或聆聽音樂時，系統播放的聲音會比Bluetooth裝置播放的聲音稍微延遲。

本系統支援符合Bluetooth標準的安全功能，能在使用Bluetooth無線技術時提供安全連線，但是取決於設定，安全性可能不足。使用Bluetooth無線技術進行通訊時請小心。

對於在Bluetooth通訊時洩漏資訊，本公司概不負責。 具備Bluetooth功能的裝置必須符合Bluetooth SIG指定

的Bluetooth標準並獲得驗證。即使連接的裝置符合上述Bluetooth標準，取決於裝置的功能或規格，部分裝置可能無法正確連接及運作。

取決於和系統連接的Bluetooth裝置、通訊環境或使用環境，可能發生雜訊或短暫無聲。

–

–––

–

–––

––

––

4 在Bluetooth裝置上執行配對程序以偵測系統。

5 選擇在Bluetooth裝置的顯示幕中顯示的“SRS-BTX500”。如果裝置的顯示幕上沒有出現“SRS-BTX500”，請從步驟2重複執行。

附註 部分裝置無法顯示偵測到的裝置清單。

6 如果Bluetooth裝置顯示幕上需要輸入密碼*，請輸入“0000”。已建立Bluetooth連線，而且系統上的Bluetooth指示燈（藍色）持續發亮。* 密碼也可以稱為“密鑰”、“PIN碼”、“PIN號”或 “口令”。

提示 若要與其他Bluetooth裝置配對，請為每一裝置重複步驟2至

6。

附註 系統的配對模式在大約5分鐘後取消，Bluetooth指示燈（藍

色）會閃爍。如果配對模式在執行此程序時取消，請從步驟3重新開始。

系統的密碼固定是“0000”。系統無法與密碼不是“0000” 的Bluetooth裝置配對。

一旦Bluetooth裝置完成配對，就不需要再次和那些裝置配對。但是在下列狀況中，您必須再次執行配對程序。

系統與9個或更多個裝置配對。 系統最多能與8個Bluetooth裝置配對。如果與8個裝置配對之後又與一個新裝置配對，此8個配對裝置中，最近連接時間為最早的裝置將由新裝置取代。

一個以上的裝置可與系統配對，但是只能從這些裝置當中的一個聽到聲音。

類型B 連接已配對的Bluetooth裝置

1 開啟系統電源。Bluetooth指示燈（藍色）會閃爍。如果AUDIO IN指示燈（黃褐色）亮起，請按下BLUETOOTH PAIRING按鈕。

2 開啟Bluetooth裝置的Bluetooth功能。

提示 對於最後連接的Bluetooth裝置，如果該裝置的

Bluetooth功能已開啟，系統會嘗試和它重新建立Bluetooth連線。建立Bluetooth連線之後，系統上的Bluetooth指示燈（藍色）會持續發亮。

3 選擇Bluetooth裝置顯示幕內顯示的 “SRS-BTX500”。必要時請從下列選擇系統支援的Bluetooth設定檔：A2DP、HSP或HFP。如需每一設定檔的詳細資訊，請參閱“何謂Bluetooth無線技術？”已建立Bluetooth連線，而且系統上的Bluetooth指示燈（藍色）持續發亮。

附註 部分裝置可能不需要此步驟。 如果系統無法連接Bluetooth裝置，請從Bluetooth裝置

刪除“SRS-BTX500”，然後再次執行配對。

Bluetooth待機模式當Bluetooth待機模式設定為開啟時，系統可由Bluetooth 裝置開啟電源和操作。

附註 如果系統是由電池供電，而且BLUETOOTH STANDBY開關設

定為開啟，即使系統關閉電源也會繼續耗用電池電力。

類型C 單觸連接智慧型手機（NFC）只要以NFC相容智慧型手機觸碰系統，系統就會自動開啟，然後和智慧型手機配對並連接。

1 在智慧型手機上下載並安裝“NFC快速連線”應用程式。“NFC快速連線”是Sony為Android電話開發的原創應用程式，可在Google Play Store中取得。請搜尋“NFC快速連線”或掃描下列二維代碼，以下載及安裝免費的應用程式。下載應用程式需要通訊費用。在部分國家/地區可能無法下載此應用程式。

提示 對於部分智慧型手機，如果沒有下載“NFC快速連線”，

可能無法使用單觸連線功能。在此狀況下，操作和規格可能不同於此處的說明。如需詳細資訊，請參閱智慧型手機隨附的使用說明書。

使用二維代碼： 使用二維代碼閱讀應用程式。

相容智慧型手機 內建NFC功能的智慧型手機

（作業系統：Android 2.3.3或更新版，不含 Android 3.x）

關於NFCNFC（近距離無線通訊；Near Field Communication）是行動電話和IC標籤等不同裝置之間進行短距離無線通訊的一項技術。憑藉NFC功能，只要觸碰NFC相容裝置上的相關符號或指定位置，就能輕易進行資料通訊。

2 啟動智慧型手機上的“NFC快速連線”應用程式。確認顯示應用程式畫面。

3 以智慧型手機觸碰系統。將智慧型手機持續觸碰系統上的N標記部分，直到智慧型手機開始震動。

智慧型手機震動 （系統已辨識）

按照螢幕上的指示建立連線。建立Bluetooth連線之後，Bluetooth指示燈（藍色）會持續發亮。

提示 如果難以建立連線，請嘗試下列操作。

啟動“NFC快速連線”應用程式，然後將智慧型手機在系統的N標記部分上稍微移動。如果智慧型手機放在保護套內，請移除保護套。

以智慧型手機再次觸碰系統，以中斷連接。

如果您擁有多個NFC相容裝置，只要將智慧型手機觸碰不同裝置，就能將連線切換到該裝置。例如，智慧型手機已和NFC相容耳機連線時，只要將智慧型手機觸碰系統，就能將Bluetooth連線切換至系統（單觸連線切換）。

–

–

–

DC IN 15V 插孔

AUDIO IN 插孔 BLUETOOTH STANDBY開關

RESET 按鈕

DC OUT ONLY 連接器（USB）

聆聽音樂您可以透過裝置內建的Bluetooth功能，以無線方式欣賞音樂。

取決於Bluetooth裝置，操作可能不同。另請參閱Bluetooth裝置隨附的使用說明書。

1 在系統和裝置之間建立Bluetooth連線。如需Bluetooth連線程序的詳細資訊，請參閱“如何與Bluetooth裝置建立無線連線”。建立Bluetooth連線之後，系統上的Bluetooth指示燈（藍色）會持續發亮。

2 在Bluetooth裝置上開始播放，然後調整音量。將Bluetooth裝置的音量調整為中等，然後按下系統上的VOLUME -/+按鈕。

自動關閉電源當沒有使用免持通話（系統不是透過HFP/HSP來連接Bluetooth裝置）、沒有裝置透過DC OUT ONLY連接器來充電，以及沒有在播放音樂時，系統會在大約20分鐘後關閉電源。

使用後執行下列任何操作。 關閉Bluetooth裝置的Bluetooth功能。如需詳細資訊，

請參閱裝置隨附的使用說明書。 關閉Bluetooth裝置的電源。 關閉系統的電源。 以智慧型手機再次觸碰系統，以中斷連接（僅限NFC相容

智慧型手機）。

聆聽音樂時使用免持通話使用具備音樂功能，而且支援Bluetooth設定檔A2DP、HFP或HSP的Bluetooth行動電話，可透過Bluetooth連線享受免持通話。如果您的Bluetooth行動電話支援HFP和HSP，請設定為HFP。

取決於Bluetooth行動電話，操作可能不同。另請參閱行動電話隨附的使用說明書。

1 在系統和行動電話之間建立Bluetooth連線。如需Bluetooth連線程序的詳細資訊，請參閱“如何與Bluetooth裝置建立無線連線”。建立Bluetooth連線之後，系統上的Bluetooth指示燈（藍色）會持續發亮。

2 在Bluetooth行動電話上開始播放，然後調整音量。將Bluetooth行動電話的音量調整為中等，然後按下系統上的VOLUME -/+按鈕。

撥打電話操作Bluetooth行動電話。檢查有聽到系統發出撥號音，然後使用麥克風通話。如果沒有聽到撥號音，按下系統上的

（撥打電話）按鈕大約2秒鐘，將通話裝置變更為系統。

接聽來電來電到達時，播放會暫停，而且系統會發出鈴聲。按下系統上的 （撥打電話）按鈕，然後使用麥克風通話。

提示 如果來電到達時，沒有聽到系統發出鈴聲，請停止播放，按

下 （撥打電話）按鈕以便通話。

播放完成時可以使用免持通話。

在通話時，按下系統上的VOLUME -/+按鈕以調整音量。

附註 在通話時，聲音僅從左揚聲器輸出。

使用智慧型手機時，請距離系統至少50 cm。如果系統和智慧型手機太靠近，可能產生雜音。

結束通話按下 （撥打電話）按鈕。如果來電到達時您正在聆聽音樂，通話結束後音樂會繼續。

使用後執行下列任何操作。 關閉Bluetooth裝置的Bluetooth功能。如需詳細資訊，

請參閱裝置隨附的使用說明書。 關閉Bluetooth裝置的電源。 關閉系統的電源。 以智慧型手機再次觸碰系統，以中斷連接（僅限NFC相容

智慧型手機）。

通話時裝置按鈕功能取決於Bluetooth行動電話，或Bluetooth行動電話支援的設定檔，可用的功能可能不同。請參閱Bluetooth行動電話隨附的操作指示。

狀態 （撥打電話）按鈕

待機 按一下以啟動語音撥號（僅限語音撥號相容行動電話）。

按住約2秒鐘以重撥上次撥打的電話號碼。

打出電話 按一下以取消打出電話。 按住約2秒鐘在系統和行動電話之間變更

通話裝置。

來電 按一下以接聽電話。 按住約2秒鐘以拒絕電話。

通話時 按一下以結束通話。 按住約2秒鐘在系統和行動電話之間變更

通話裝置。

聆聽音樂時以另一個Bluetooth行動電話使用免持通話本系統相容於多點技術，此技術允許您使用免持通話，同時聆聽來自於Bluetooth相容音樂播放器的音樂。

在此程序中無法使用單觸連線（NFC）。 操作可能因Bluetooth裝置而異。取決於Bluetooth裝置

的組合，可能無法建立這種類型的Bluetooth連線。另請參閱Bluetooth裝置隨附的操作指示。

1 在系統和Bluetooth音樂播放器之間透過A2DP建立Bluetooth連線，而在系統和Bluetooth行動電話之間透過HFP或HSP建立Bluetooth連線。如需Bluetooth連線程序的詳細資訊，請參閱“如何與Bluetooth裝置建立無線連線”。建立Bluetooth連線之後，系統上的Bluetooth指示燈（藍色）會持續發亮。

提示 若僅使用也具備音樂功能的Bluetooth行動電話的通話功

能，請在系統和行動電話之間透過HFP或HSP，而非A2DP建立Bluetooth連線。

取決於Bluetooth行動電話，透過HFP或HSP建立Bluetooth連線時，透過A2DP的其他Bluetooth連線可能遭到相同Bluetooth行動電話佔用。在此狀況下，Bluetooth音樂播放器無法連接本系統。

附註 若要在關閉系統電源後和相同裝置建立相同連線，請再執

行此程序。

N標記

BATTERY/CHARGE 指示燈

VOLUME −/+ 按鈕

（撥打電話）按鈕

SOUND按鈕/指示燈

AUDIO IN按鈕/指示燈

BLUETOOTH PAIRING 按鈕Bluetooth指示燈

/按鈕

照明燈 麥克風

側邊支架

若要享受音效設定您可以享受想要的音效設定。

1 按下SOUND按鈕以選擇音效。SOUND指示燈（參閱下述）顯示目前的音效設定。您可以重複按下SOUND按鈕，在音效之間切換。

狀態 音效

黃褐色 將聽到優質低音（增強低音）。您首次開啟系

統電源時，預設啟用此設定。

綠色 將聽到環繞聲音（增強低音+環繞）。

熄滅 音效關閉。

提示 系統在下一次開啟電源時，會記得上一次的音效設定。

透過有線連線可攜式音訊裝置等聆聽音樂1 將裝置連接系統。

連接線（未隨附）

（立體聲迷你插孔）

2 開啟系統的電源。

3 開啟所連接裝置的電源。

4 按下系統上的AUDIO IN按鈕。

5 操作連接的裝置。將所連接裝置的音量調整為中等，然後按下系統上的VOLUME -/+按鈕。

附註 僅以連接線連接系統並不能播放音樂。請務必也要按下AUDIO

IN按鈕。

您在聆聽以連接線連接系統的裝置所播放的音樂時，無法使用免持通話。

自動關閉電源 當沒有使用免持通話（系統不是透過HFP/HSP來連接Bluetooth裝置）、沒有裝置透過DC OUT ONLY連接器來充電，以及沒有在播放音樂時，系統會在大約20分鐘後關閉電源。

透過連接系統的USB連線，將USB裝置充電，例如智慧型手機將智慧型手機連接系統的DC OUT ONLY連接器（USB），就能為智慧型手機充電。當僅以內建電池來使用系統時，您也可以從系統的電池將智慧型手機充電。開啟系統電源以便將USB裝置充電。

USB纜線（未隨附）

附註 此功能不適用於透過USB纜線的資料通訊。

系統的丟棄為保護環境，請從系統中移除內建的鋰離子電池。移除電池之前，請移除交流轉接器，僅以電池使用系統以耗盡電池電力。

取出鋰離子電池以便回收。除了在丟棄系統時，請勿開啟機箱。

1 關閉系統電源，移除交流轉接器。

2 拆下系統背蓋以移除電池組。打開支架。 移除系統底部的4個橡膠蓋。移除4個螺絲。移除蓋子。從系統移除連接器插頭。移除電池。

附註 您從系統移除電池組時，請小心不要以金屬鑷子等損壞代碼

蓋。

規格揚聲器部分揚聲器系統 衛星揚聲器：直徑約48 mm × 2

低音揚聲器：直徑約80 mm × 1

機殼類型 衛星揚聲器：密封式音箱 低音揚聲器：被動輻射器機型

放大器部分參考輸出功率 使用交流電源供應器：10 W + 10 W

（衛星揚聲器，1%諧波失真，1 kHz， 6 Ω），20 W（低音揚聲器，1%諧波失真，100 Hz，4 Ω） 使用電池：4 W + 4 W（衛星揚聲器， 10%諧波失真，1 kHz，6 Ω）， 8 W（低音揚聲器，10%諧波失真， 100 Hz，4 Ω）

Bluetooth通訊系統 Bluetooth規格版本3.0

輸出 Bluetooth規格功率等級2

最大通訊距離 視線約10公尺*1

頻帶 2.4 GHz頻帶 （2.4000 GHz - 2.4835 GHz）

調變方法 FHSS

相容Bluetooth設定檔*2 A2DP（進階播音設定檔） AVRCP（音訊/視訊遠端控制設定檔） HSP（耳機設定檔） HFP（免持設定檔）

支援的編碼解碼器*3 SBC*4，AAC*5

傳送距離（A2DP） 20 Hz - 20000 Hz （取樣頻率44.1 kHz）

*1 取決於裝置之間的障礙物、微波爐周圍的磁場、靜電、接收靈敏度、天線效能、作業系統、軟體應用程式等因素，實際的距離可能不同。

*2 Bluetooth標準設定檔代表裝置之間Bluetooth通訊的目的。

*3 編碼解碼器：音訊訊號的壓縮和轉換格式*4 子頻帶編碼解碼器*5 進階音訊編碼

麥克風類型： 駐極體電容器

方向特性： 全向

有效頻率範圍： 50 Hz-10 kHz

一般輸入 AUDIO IN插孔（ø 3.5 mm立體聲迷你插

孔）

DC OUT USB插孔類型A（用於將連接的裝置之電池充電）（5 V，最大1.5 A）

電源 直流15V（使用隨附的交流電源供應器連接至交流100 V-240 V、50 Hz/ 60 Hz的電源）或，使用內建鋰離子電池

鋰離子電池壽命（使用Bluetooth連線） 約6小時*6

尺寸（含突出的零件和控制鈕） 約385.0 mm × 152.0 mm × 65.0 mm （寬/高/深）

質量 約2,000 g

包含電池

隨附配件 交流電源供應器（AC-E1530）（1） 使用說明書（本文件）（1） Bluetooth® 啟動指南（1） 攜帶包（1）

*6 取決於溫度或使用條件，時間可能不同。

設計和規格若有變更恕不另行通知。

移難排解

沒有聲音/聲音僅來自於一個揚聲器/低音量

檢查本系統和所連接裝置的電源均開啟。

如果您正將個人電腦連接到系統，請確認已為Bluetooth裝置設定電腦的音訊輸出設定。

提高系統和所連接裝置的音量。 再次配對本系統和Bluetooth裝置。

檢查連接的裝置正在播放。 如果連接的裝置是單聲道，聲音將從左揚聲器輸出。

檢查連接線（未隨附）的兩端插頭均穩固插入系統和連接的裝置內。

聲音失真/系統輸出有哼聲或雜訊

降低所連接裝置的音量。 請將系統遠離電視機。

如果連接的裝置具有等化器功能，請將它關閉。

在已設定HFP或HSP時，操作Bluetooth裝置將Bluetooth連線切換為A2DP。

請將系統遠離微波爐、無線LAN等。

如果將內建收音機或調諧器的裝置連接到本系統，則可能收不到廣播，或靈敏度可能下降。將系統遠離裝置，檢查廣播的效果是否令您滿意。

將本系統和Bluetooth裝置靠近一些。移除本系統和Bluetooth裝置之間的任何障礙物。

如果BATTERY/CHARGE指示燈閃爍綠色，請連接交流轉接器將系統充電。

無法配對

使本系統和Bluetooth裝置相距1公尺內。

如果Bluetooth指示燈（藍色）沒有快速閃爍，請按住系統上的BLUETOOTH PAIRING按鈕直到聽到兩聲嗶聲為止。

沒有聲音/接收器聲音低

檢查本系統和所連接裝置的電源均開啟。

操作Bluetooth裝置以選擇HFP或HSP Bluetooth連線。

檢查已為系統設定Bluetooth行動電話的輸出。

提高系統和所連接裝置的音量。

無法進行單觸連線（NFC）

讓智慧型手機靠近系統，直到智慧型手機開始震動。如果失敗，請將智慧型手機在系統的N標記部分上稍微移動。

如果智慧型手機放在保護套內，請移除保護套。

檢查智慧型手機的NFC功能設定為開啟。

NFC的接收靈敏度取決於裝置。如果以單觸連接智慧型手機失敗數次，請按照螢幕上的操作連接至系統。

檢查智慧型手機上顯示“NFC快速連線”應用程式。

亮起