Top Banner
The Capco Pascall Catalogue 2006
28
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: Pascall_catalogue - CAPCO

The Capco Pascall Catalogue

2006

Page 2: Pascall_catalogue - CAPCO
Page 3: Pascall_catalogue - CAPCO

The Company

1

Capco Test Equipment Ltd are one of the leading manufacturers of Testing Equipment and have been associated with Quality Testing Equipment for well over half a century. We purchased Pascall

Engineering in 2004 and continue to manufacture their whole range of products.

Our headquarters are located at Wickham Market in Suffolk, UK, from where we manufacture all types of Civil Engineering Test Equipment for worldwide sale. Our full range encompasses everything needed for today’s Civil Engineering industry, both in the laboratory and on site. Our products range from the smallest mechanical devices to the most highly sophisticated electrical devices, and includes the full

range of equipment previously manufactured by Pascall Engineering.

All of our products are subject to the strictest Quality Control procedures to ensure that the highest possible standards are maintained throughout.

To make buying easier, so that all of your requirements are met in one easy step, you can phone, fax or

e-mail us, with your details. All purchase cards and credit cards are accepted.

NB: Model code No. The last letter of the model code No. denotes the electric supply. Those shown (A or C) are the common European Single and three phase electric supplies currently in use.

Please amend the code to suit your requirements using the following suffixes:

A = 230V-IPH-50Hz B = 110V-IPH-60Hz C= 400V-3PH-50Hz

D = others, specify on your order.

Extra costs maybe incurred where electric supplies other than A or C are required. Flameproof and air motors can be supplied for some machines; details on request.

Electrical Specification

Managing Director: Tammy Robertson

Technical Director: Andrew Robertson

Pascall Enquiries: Claire Robertson

Civil Enquiries: Tammy Robertson

Contacts

1 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 4: Pascall_catalogue - CAPCO

Contents

2 2 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Colour Section Page Numbers

Ball Mills 4, 5, 6

Conical Lab Mixer 7

Disc Grinder 8

Jaw Crusher 9, 10

Mortar and Pestle Mills 11, 12

Ribbon Blade Powder Mixer 13

Sample Dividers 14, 15, 16

Sieve Shakers 17, 18

Sieves 19

Triple Roll Mills 20, 21, 22

Winnower & Cocoa Breaker 23

Conversion Tables 24

Conditions of Sale 25

Contact Us 26

Page 5: Pascall_catalogue - CAPCO

Pascall laboratory ball mills provide operators with a wide choice. The range includes both small laboratory units to handle single containers as well as multi-tiered units capable of accommodating milling containers up to 35 litres nominal capacity. All models can be supplied with variable speed control and, with the exception of Model 9, with flameproof drive units for use in hazardous areas. Unless otherwise specified all models are fitted with an electrically interlocked roller guard to prevent access to the rollers whilst the mill is in operation. Accessories for use with the mills include various types of grinding media, screens, pourers, and tipping stands for straining the contents from the mill pots. This equipment is a useful compliment to any ball milling operation where several samples may be being processed at any one time. The porcelain pots are made from industrial porcelain having an alumina content of approx. 50% and have excellent acid and corrosion resisting properties. The pots are fitted with flat ground tops and lids. The steel pots are of a welded construction with lid and locking clamps similar to those fitted to the porcelain pots.

Ball Mills Overview

3

Part Code Description Model Code BALLJARMILL 2VAR Model 2 Variable Speed 1600-VS-A

BALLJARMILL 3FIX Model 3 Fixed Speed 1144-FS-C

BALLJARMILL 3VAR Model 3 Variable Speed 1144-VS-A

BALLJARMILL 4FIX Model 4 Fixed Speed 1492-FS-A

BALLJARMILL 4VAR Model 4 Variable Speed 1492-VS-A

BALLJARMILL 5FIX Model 5 Fixed Speed 1556-FS-C

BALLJARMILL 5VAR Model 5 Variable Speed 1556-VS-A

BALLJARMILL 6FIX Model 6 Fixed Speed 1544-FS-C

BALLJARMILL 6VAR Model 6 Variable Speed 1545-VS-A

BALLJARMILL 7FIX Model 7 Fixed Speed 1451-FS-A

BALLJARMILL 7VAR Model 7 Variable Speed 1451-VS-A

BALLJARMILL 8FIX Model 8 Fixed Speed 1553-FS-A

BALLJARMILL 8VAR Model 8 Variable Speed 1597-VS-A

BALLJARMILL 9VAR Model 9 Variable Speed 1679-VS-A

BALLJARMILL 10FIX Model 10 Fixed Speed 1546-FS-A

BALLJARMILL 10VAR Model 10 Variable Speed 1547-VS-A

BALLJARMILL 11OTF Model 11 (One-Tier) Fixed Speed 1221-FS-1-C

BALLJARMILL 11OTV Model 11 (One-Tier) Variable Speed 1221-VS-1-C

BALLJARMILL 11TTFIX Model 11 (Two-Tier) Fixed Speed 1221-FS-2-C

BALLJARMILL 11TTVAR Model 11 (Two-Tier) Variable Speed 1221-VS-2-C

BALLJARMILL 12VAR Model 12 Variable Speed 1601-VS-A

Machines

Ball Mill No. 9

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 6: Pascall_catalogue - CAPCO

Model Motor Electric Supply

Weight (kg)

Height (mm)

Depth (mm)

Width (mm)

Roll Length (mm)

Guard Pot

Capacity (litre)

Flame Proof

Roll Speed (rpm)

No 2** 180W 230v/ 1ph/50Hz 44 327 376 756 363 std 0.5-5.0 option 244

Var speed (option) 180W 230v/

1ph/50Hz 47 327 376 756 363 std 0.5-5.0 option 0-420

No 3 0.55kW 400v/ 3ph/50Hz 109 1005 625 964 730 std 5.0-35.0 option 296

Var speed (option) 0.55kW 230v/

1ph/50Hz 109 1005 625 964 730 std 5.0-35.0 option 0-420

No 4** 0.37kW 230v/ 1ph/50Hz 62 471 427 976 419 std 5.0-10.0 option 285

Var speed (option) 0.37kW 230v/

1ph/50Hz 68 471 427 976 419 std 5.0-10.0 option 0-400

No 5 0.37/ 0.55kW

400v/ 3ph/50Hz 287 1186 716 1500 N/a std 15.0-35.0 option N/a

Var speed (option)

0.37/ 0.55kW

230v/ 1ph/50Hz 287 1186 716 1500 N/a std 15.0-35.0 option N/a

No 6 0.37kW 230v/ 1ph/50Hz 285 1561 514 1498 3x1021 std 0.5-5.0 option 198/

286

Var speed (option) 0.37kW 230v/

1ph/50Hz 295 1561 514 1612 3x1021 std 0.5-5.0 option 0-420

No 7 0.55kW 230v/ 1ph/50Hz 185 829 808 1049 809 std 0.5-10.0 option 198

Var speed (option) 0.55kW 230v/

1ph/50Hz 185 829 808 1049 809 std 0.5-10.0 option 0-420

No 8 0.37kW 230v/ 1ph/50hz 155 921 514 1498 1021 std 0.5-5.0 option 198/

286

Var speed (option) 0.37kW 230v/

1ph/50hz 155 921 514 1612 1021 std 0.5-5.0 option 0-420

No 9 var speed std**

50W 230v/ 1ph/50hz 14 210 250 400 190 std 0.5-1.0 N/a 0-350

No 10 0.37kW 230v/ 1ph/50hz 195 1127 514 1498 2x1021 std 0.5-10.0 option 198/

286

Var speed (option) 0.37kW 230v/

1ph/50Hz 195 1127 514 1612 2x1021 std 0.5-10.0 option 0-420

No 11 0.75kW 400v/ 3ph/50Hz 562 1217 676 2366 4x787 std 10.0-35.0 option 240/

290

Var speed (option) - - 562 1217 676 2366 4x787 std 10.0-35.0 option 0-420

No 12** 180W 230v/ 1ph/50Hz 47 278 376 988 595 std 0.5-2.5 option 244

Var speed (option) 180W 230v/

1ph/50Hz 56 278 376 988 595 std 0.5-2.5 option 0-420

Ball Mills

4

* Other windings available ** Bench Top Models

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 7: Pascall_catalogue - CAPCO

Nominal

Capacity Diameter Diameter Diameter Diameter Total

Litres 9.5 12.7 19.0 25.4 Weight 0.5 0.3 0.3 0.4 - 1.0

1.0 0.6 0.6 0.8 - 2.0

2.5 - 1.5 1.5 2.0 5.0

5.0 - 3.0 3.0 4.0 10.0

10.0 - 6.0 6.0 8.0 20.0

15.0 - 9.0 9.0 12.0 30.0

20.0 - 12.0 12.0 16.0 40.0

30.0 - 18.0 18.0 24.0 60.0

35.0 - 21.0 21.0 28.0 70.0

Carbon / Stainless Steel

Capacity Porcelain Steel

Litres O/Diameter O/Length Weight O/Diameter O/Length Weight 0.5 121 147 1.5 100 135 1.8

1.0 140 176 2.2 125 173 2.6

2.5 159 270 4.5 140 219 4.8

5.0 229 325 13.3 213 232 10.0

10.0 279 368 20.0 251 290 14.0

15.0 355 371 33.6 - Non std -

20.0 355 517 41.0 328 341 22.5

30.0 420 525 54.4 - Non std -

35.0 n/a n/a n/a 356 495 27.0

Technical Data for Ball Mill Pots (dimensions in mm, weights in kg)

Ball Mills

Nominal Steatite Alumina

Capacity Diameter Diameter Diameter Diameter Total Diameter Diameter Total

Litres 9.5 12.7 19.0 25.4 Weight 19.0 25.4 Weight 0.5 0.1 0.1 0.15 - 0.35 0.22 0.22 0.44

1.0 0.2 0.2 0.30 - 0.70 0.45 0.45 0.90

2.5 - 0.5 0.50 0.75 1.75 1.12 1.12 2.24

5.0 - 1.0 1.00 1.50 3.50 2.25 2.25 4.50

10.0 - 2.0 2.00 3.00 7.00 4.50 4.50 9.00

15.0 - 3.0 3.00 4.50 10.50 6.75 6.75 13.50

20.0 - 4.0 4.00 6.00 14.00 9.00 9.00 18.00

30.0 - 6.0 6.00 9.00 21.00 13.50 13.50 27.00

Technical Data for Ball Charges (dimensions in mm, weights in kg)

5 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 8: Pascall_catalogue - CAPCO

Ball Mill Accessories Screen type pourers and liquid pourers are available for all sizes of pots as well as tipping stands for use when draining the pots. Certain models can be fitted with vibratory motors to rapidly discharge the material. These are very useful when handling a powdered or viscous material which may tend to stick. Various different types of grinding media can be used in order to obtain maximum grinding efficiency. For the ceramic pots steatite or high density alumina balls are generally used whilst for the steel pots either carbon or stainless steel balls are the norm. Other media such as zirconia or glass balls can be supplied to order. Speed, material charge and size of grinding media all play an important part in milling efficiency. The tables shown are for general use but have been found to produce good results over a very wide range of materials.

Overview Accessories

6 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 9: Pascall_catalogue - CAPCO

Machines Partcode Description Model Code

MIXCONLAB Conical Lab Mixer 1664-00-A

Partcode Description Model Code MIXCON BAR 1.5S 1.5 litre standard barrel 1665-02

MIXCON BAR 1.5V 1.5 litre vaned barrel 1665-03

MIXCON BAR 6S 6 litre standard barrel 1664-03

MIXCON BAR 6V 6 litre vaned barrel 1664-04

Accessories

Conical Lab Mixer

A tumbler mixer for blending powders or liquids. Bench Mounted and fitted with a hexagonal conical type polypropylene barrel with screw-on lid. The barrel can be fitted with vanes for mixing high density materials. The drive is by a geared motor unit giving barrel speeds from 0-50rpm and a 0-99min timer is fitted into the facia of the unit. Capacity: Nominal 1.5 or 6.0 litres Electrics: 230v / 1ph / 50 Hz Dimensions: 440mm (height) 445mm (width) 450mm (depth) Nett weight: 18kg Finish: Blue

Overview

7

Conical Lab Mixer

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 10: Pascall_catalogue - CAPCO

Partcode Description Model Code DISCGRIND1 Model 1 disc grinder 1396-00-C

DISCGRINDVIB Vibratory feeder & hopper 1539-00-A

Machines

Disc Grinder The Pascall Disc Grinder has been designed in conjunction with the Pascall Jaw Crusher to reduce crushed product to a finer particle size. However it may be used as a separate processing unit for reducing a wide range of materials. The grinding operation which takes place between two 203 mm hardened chrome steel discs is completely enclosed in an easily accessible but safety interlocked chamber. Throughputs vary up to 50kgs/hr depending on the material being processed and the product size required. For materials which may not feed easily a vibratory feeder/hopper is available as an optional extra. Drive is by a 2.2kw motor wound for 400v—3 ph—50hz (feeder single phase).

Disc Grinder Overview

8 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 11: Pascall_catalogue - CAPCO

Jaw Crushers

Machines Picture Description Model Code

Model No 1 has a jaw opening of 76mm x 51mm. The drive is by a 750W motor wound for 380/415-3-50Hz (other voltages can be supplied) with the transmission through a vee belt pulley drive

1600-VS-A

Model No 2 has a jaw opening of 152mm x 76mm. The drive is by a 4kW motor wound for 380/415-3-50Hz (other voltages can be supplied) with the transmission through a toothed timing belt. The main body of the Model No 2 together with motor and transmission are totally enclosed within moulded protective casings which form the drive guards and covers, and the complete unit is arranged on a compact, rigid and robust stand. The floor space required is approximately 1181mm x 762mm. The overall height is about 1406mm, and the approximate nett weight 508kg.

1144-FS-C

Partcode JAWCRUSHER1

JAWCRUSHER2

Used for laboratory and production purposes for crushing various hard, semi-hard and soft friable material such as abrasives, aggregate, chemicals, clays, coal, coke, foundry sands, gravel, minerals, natural and synthetic polymers, refractories and sintered metal powders. Depending on the nature of the raw material, the size reduction is to about 6mm and finer on No. 1 and to about 10mm and finer on No. 2. Heavy cast iron body and moving jaw stocks. Incorporate feed chutes with protective grids and covers. Model No 1 discharge outlet is through a delivery chute fitted with protective baffle plate below the jaws. Model No 2 has a circular discharge outlet with a protective grid. The moving and fixed jaws of both models are fitted with replaceable ribbed manganese steel jaw plates, and the sides of the crushing chambers are lined with replaceable hardened steel wear plates.

Overview

The gap or nip between the moving and fixed jaws on both models can be adjusted for fine or coarse crushing by means of a hand wheel located at the back of the crusher. To maintain the gap selected the hand wheel is equipped with a locking hub. The moving jaw of both models can be fully retracted for ease of cleaning or to dislodge material from the crushing chamber. The moving jaw of each model is carried on an eccentric shaft fitted with a flywheel and a belt driven pulley. The bearings are bronze, oil impregnated and self oiling, and supplementary grease lubrication through grooves in the eccentric shaft and sealing discs protect the bearings from the ingress of dirt. The driving motor of each model is wired to a push-button motor control switch (star delta in the case of Model No 2) with no volt and overload release features which protect the machine from damage in the event of uncrushable material becoming jammed between the jaws.

Jaw Crushers

9 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 12: Pascall_catalogue - CAPCO

Machines Partcode Dimensions (mm) Model Code Weight

JAWCRUSHER1 464 x 479 x 1156 1397-00C 178 Kg

JAWCRUSHER2 1181 x 762 x 1406 1398-00C 508 Kg

Jaw Crushers

10 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 13: Pascall_catalogue - CAPCO

Machines Model 00 0 1 2 3

Capacity (ml) 25 250 1000 2250 7000

Mortar Diameter (mm) 100 178 254 381 508

Pestle Diameter (mm) 50 76 121 197 248

Mortar Speed (rpm) 32 70 60 40 30

Elec Volts 230 230 400 400 400

Ph 1 1 3 3 3

Hz 50 50 50 50 50

Motor (W) 90 & 30 180 550 750 1500

Net Weight: Steel (kg) 29 45 157 228 509

Porcelain (kg) - 43 144 - -

Dimensions (mm) 254 x 380 304 x 484 538 x 348 685 x 452 717 x 728

W x D x H (mm) 354 480 1158 1245 1790

Mortar & Pestle Mills Models 1, 2 & 3: These mills are all floor standing but basically of the same design as the smaller Model 0. Friction between the mortar and the pestle causes the pestle to rotate and being free to float up and down adjusts itself to take under the pestle larger particles of material. All three may be fitted with either stainless steel or cast iron mortar and pestle. The model 1 is also available fitted with hard, acid resisting porcelain mortar and pestle.

Model 00: Unequalled for rapid, micro fine particle size reduction of a variety of materials the mill is supplied complete with individually driven mortar and pestle of polished agate or tool steel. The mill contains two main sections hinged at the back and secured by quick release clamps which can be adjusted to vary the grinding pressure. A protective electrically interlocked safety guard encloses the mortar and pestle and automatically switches off the motor when removed.

Overview

Model 0: This model is an invaluable mill for dry or wet processing. It is an ideal laboratory unit for small quantities of expensive materials or for routine grinding of large numbers of test samples. The mill is portable but robust making it easy to handle by junior laboratory technicians. The weighted pestle which is offset in the mortar floats in the hinged arm bracket by means of a quick release set screw. When lifted the arm swings clear of the mortar allowing it to be removed from the turntable for emptying and cleaning.

11

Model 2

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 14: Pascall_catalogue - CAPCO

Machines Partcode Description Model Code Weight (kg)

MORTARMILL 00A Agate mortar & pestle 1563-A-A 29

MORTARMILL 00SA Steel mortar & pestle 1563-S-A 29

MORTARMILL 0P Porcelain mortar & pestle 1193-P-A 43

MORTARMILL 0S Cast iron mortar/steel pestle 1193-S-A 45

MORTARMILL 0SS Stainless steel mortar & pestle 1193-SS-A 45

MORTARMILL 1P Porcelain mortar & pestle 1099-P-C 144

MORTARMILL 1SC Cast iron mortar/steel pestle 1099-S-C 157

MORTARMILL 1SS Stainless steel mortar & pestle 1099-SS-A 157

MORTARMILL 1PH Mortar heating facility 1099-HM -

MORTARMILL 2C Cast iron mortar & pestle 1143-S-C 228

MORTARMILL 2SS Stainless steel mortar & pestle 1143-SS-C 228

MORTARMILL 2CH Mortar heating facility 1143-HM -

MORTARMILL 3C Cast iron mortar/steel pestle 1145-S-C 509

MORTARMILL 3SS Stainless steel mortar & pestle 1145-SS-C 509

MORTARMILL 3CH Mortar heating facility 1145-HM -

Mortar & Pestle Mills

12 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 15: Pascall_catalogue - CAPCO

Ribbon Blade Powder Mixer Model 6 Overview

13

Machines Model Part Code Description Model Code

0 MIXPOWRIB0MS Ribbon blade powder mixer model 0 mild steel 1219-MS-A

MIXPOWRIB0SS Ribbon blade powder mixer model 0 stainless steel 1219-SS-A

1 MIXPOWRIB1MS Ribbon blade powder mixer model 1 mild steel 1080-MS-C

MIXPOWRIB1SS Ribbon blade powder mixer model 1 stainless steel 1080-SS-C

2 MIXPOWRIB2MS Ribbon blade powder mixer model 2 mild steel 1102-MS-C

MIXPOWRIB2SS Ribbon blade powder mixer model 2 stainless steel 1102-SS-C

3 MIXPOWRIB3MS Ribbon blade powder mixer model 3 mild steel 1083-MS-C

MIXPOWRIB3SS Ribbon blade powder mixer model 3 stainless steel 1083-SS-C

4 MIXPOWRIB4MS Ribbon blade powder mixer model 4 mild steel 1104-MS-C

MIXPOWRIB4SS Ribbon blade powder mixer model 4 stainless steel 1104-SS-C

5 MIXPOWRIB5MS Ribbon blade powder mixer model 5 mild steel 1105-MS-C

MIXPOWRIB5SS Ribbon blade powder mixer model 5 stainless steel 1105-SS-C

6 MIXPOWRIB6MS Ribbon blade powder mixer model 6 mild steel 1106-MS-C

MIXPOWRIB6SS Ribbon blade powder mixer model 6 stainless steel 1106-SS-C

Model 0 1 2 3 4 5 6 Mixing Capacity (litres) 21 57 113 170 225 283 625

Power Required* (W) 180 550 750 750 1500 1500 4000

Net Weight (Kg) 80 150 215 300 394 600 800

Floor Space (mm) 1143 X 362 1620 X 406 1620 X 603 2062 X 603 2408 X 603 2743 X 603 3023 X 724

Height Lid Closed (mm) 622 1194 1321 1524 1524 1524 1680

Lid Open (mm) 863 1575 1816 2032 2032 2032 2413

Pascall Powder Mixers are unequalled for ease of installation and maintenance, reliability in service and economy in operation. They are used in many industries, chemical, cosmetics, colours and dyestuffs, food, pharmaceutical and plastics, for processing a wide variety of powdered products. The seven models available can be supplied fabricated from either heavy gauge mild steel or stainless steel, and, in addition to mixing and blending, they can be adapted for drying by fitting electrically heated jackets. The output possible from any one depends upon the bulk density of the material. The standard design of Pascall Powder Mixers is a heavy gauge steel U-Trough, set and sealed between robust steel end plates with the open top covered by a dust tight lid. The main shaft running through the trough and end plates is carried on outrigger bearings, and glands are fitted on the revolving shaft and end plates to effectively seal the interior of the trough.

The shaft length in the trough is fitted with steel bosses carrying the specially designed flights of ribbon type, spiral mixing blades — a feature which greatly facilitates cleaning. The spiral mixing blades have a contra-flow action which not only quickly produces a thorough and homogeneous blend of the powders but also directs the mixing to the discharge outlet at the base of the trough, making the mixer self-emptying. On standard models a sliding gate valve is fitted but valves to customers’ own specifications can be supplied if required. Apart from the Model 0, which is roller chain drive, all other models are fitted with geared motor units coupled direct to the mixer shaft, and the standard motor fitted is wound for 415-3-50 Hz, but motors of other windings can be supplied. All models are fitted with push-button starters with no volt and overload release features, and with safety switches and guards to safeguard operatives from the rotating mixer blades. Flameproof or pneumatic motor drives are also available.

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

FAX: 01728 747599 WEB: WWW.CAPCO.CO.UK COMPANY NO.: 2151569

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

* The power requirement quoted are for materials of average bulk density, free flowing and of a powdery nature

Page 16: Pascall_catalogue - CAPCO

• For quickly obtaining a small representative sample of a powdered material for sieve analysis, particle size range or for chemical analysis.

• Hopper, base, turntable, distributor cone, dust cover in aluminium. • Stainless steel sample collecting bins • Stainless steel lever operated valve • Easy cleaning of detachable valve • Power requirement: 230v-1 ph-50Hz

Sample Dividers An extremely useful laboratory sample divider which meets the requirements of BS3406-1-1986 for quickly obtaining a small representative sample of a powdered material for sieve analysis of the particle size range or for chemical analysis. The divider consists of a stationary hopper mounted on three support columns connected to the base casting, a turntable driven at 52rpm by a 30W geared motor unit housed in the base, and six sample collecting bins secured on the turntable by quick release clips and covered with an easily detachable two-piece cover for dustless operation. The powder cascades from the hopper through a lever operated valve on to a distributor cone and into the rotating sample bins and each division is composed of the same particle size range as in the bulk example. The rate of discharge of the powder from the hopper is controlled by the valve and this can be varied from a trickle to the full 25mm bore of the hopper outlet. The hopper capacity is 2.5 litres, but the quantity of powder that can be placed in the hopper depends upon the density of the powder to be divided.

Overview

14

Rotary Cascade Model 1

• Invaluable time savers for accurate division of gross samples of coal, coke & other powdered materials of less than 20mm initial size.

• Robust construction • Set up on any reasonably flat surface • Base casting fitted with spirit level indicator • Three coned steel feet, two are adjustable • 90W geared motor driving turntable at 59rpm • Power requirements 230v-1ph-50Hz

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Designed specifically to meet the requirements of BS1017-1-1989 & BS1017-2-1994, these sample dividers are invaluable time savers for the accurate division of gross samples of coal, coke and other powdered materials of less than 20mm initial size. The sample collecting bins consisting of two each 1/12, 1/6 and 1/4 of the gross sample are located on the turntable and held in position with quick release clips, and are completely surrounded by a steel, dust tight outer casing. The bins fit around a hollow centre column which is an integral part of the turntable. Sliding up and down within the hollow centre column is a vertical shaft topped with a distributor cone. The cone projects into the hopper throat and keeps the discharge outlet closed until the divider is ready for use. The rise and fall of the vertical shaft is controlled by a foot pedal, the travel of which can be adjusted to vary the discharge rate of the material from the hopper. The hopper assembly, which is supported on two steel columns projecting from the base casting, accurately registers with the outer cover surrounding the sample collecting bins to make the divider dustless in operation. The register is obtained by means of a truncated cone situated on top of the right-hand support column and a mating recess in the hopper assembly bracket. Access to the sample collecting bins is a simple matter of lifting the lever on the left-hand side of the hopper assembly. The up and over movement of the lever operates a cam sliding on a ball bearing mounted on the top left-hand support column, and elevates the entire hopper assembly clear of the outer cover and the distributor cone. The hopper can then be swung to one side and the sample collecting bins lifted out after first removing the distributor cone.

Overview Rotary Cascade Model 2

Rotary Cascade Model 3

Page 17: Pascall_catalogue - CAPCO

Sample Dividers A description of the divider and its method of use is given in the Rules for Seed Testing issued by the International Seed Testing Association. The gross seed sample for division is placed in the hopper and it flows on to a shallow, dished spinner which distributes the seed centrifugally over a two-way dividing head. The divisions are channelled through two side outlets into suitable collecting bowls placed under the spouts. The action is extremely fast enabling the operator to obtain samples and sub-samples in rapid succession until the required quantity is required. The unit consists of a stationary stainless steel hopper of approx. 4 litres capacity located immediately over a 102mm diameter spinner situated above a spiral fluted, cast bronze two way dividing head surrounded by an outer cover to which the two outlets are attached, all mounted on a powder coated base.

Overview

15

Centrifugal Seed Divider

• Used by Official Seed Testing Station for England & Wales, & by many Seed Growers Associations & Seed Merchants Worldwide

• Bench mounted • Suitable for all kinds of seeds except chaffy types • Invaluable unit for the rapid provision of a seed sample for purity tests or for germination capacity under the specifica-

tions of the Seeds Act • Can also be used for obtaining representative samples of other hard, free flowing granular materials • Stainless steel hopper of 4litres capacity • Spinner driven at approx. 450rpm by a 50W geared motor unit • Hopper easily detached for access to spinners • Divider fitted with off bias push button switch • Easily viewed spirit level indicator on base casting, 3 feet, one fixed and two adjustable • Power requirements 230v-1ph-50Hz

Overview Wholestream Model

• Extremely accurate • Suitable for small and medium size samples • 6 stainless steel sample collecting bins • Turntable rotating at approx. 52rpm secured by quick release strap and detachable stainless steel clips • Vibrating feeder unit mounted above bins • 2.6 litre hopper • Controlled rate of feed to suit materials of varying bulk densities • 60W geared motor unit • Power requirement 230v-1 ph-50Hz

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

The spinner is driven at approx. 450rpm by a 50W geared motor unit housed in the base. The vertical spindle carrying the spinner extends beyond the spinner into the hopper throat. Mounted on top of the spindle is a hard, tufnol impeller which disturbs the seed and prevents blockages occurring in the hopper.

Page 18: Pascall_catalogue - CAPCO

Partcode Description Dimensions (mm) Model Code Weight (kg)

SAMDIV1RCAS Rotary sample divider cascade model 1 Base diameter: 368 Height: 596 1189-00-A 25

SAMDIV2RCAS Rotary sample divider cascade model 2 Base diameter: 610 Height: 1057 1198-2-A 171

SAMDIV3RCAS Rotary sample divider cascade model 3 Base diameter: 610 Height: 1305 1198-3-A 194

SAMDIV1VRW Rotary wholestream divider 580 x 264 x 800 1666-00-A 30

SEEDDIVCEN Centrifugal seed divider Base diameter: 324 343 (w) x 534 (h) 1200-00-A 23

Machines

Sample Dividers

16 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 19: Pascall_catalogue - CAPCO

Machines Partcode Description Model Code Weight (kg) SISHINC1 Model 1: Heavy duty floor mounted shaker to

accept 12x200mm (8”) or 15x100mm (4”) diameter sieves.

1132-1-A 69

SISHINC2 Model 2: Heavy duty floor mounted shaker to accept 12x200mm (8” diameter) or 7x300mm (12” diameter) sieves.

1132-2-A 74

SISHINC3 Model 3: Heavy duty floor mounted shaker to accept 14x200mm (8”) or 7x300mm (12”) or 5x450mm (18”) sieves.

1132-3-A 79

Model 1 Model 2 Model 3

Machine

At the same time the table of the Inclyno lifts and falls over a short distance at a frequency of approx. 300 jolts per minute, and the simultaneous action of both movements presents the particles of the test material at all possible angles and each particle is given the optimum chance of passing through the apertures of the sieve. All models are fitted with a quick release sieve clamping mechanism which securely locks the nest of sieves in place. The Inclyno is operated by a 180W motor and supplied complete with an electronic timer time switch which allows the unit to be used over a pre-determined period from 0-99 minutes. Shakers available in 230 or 110 volt. Powdered materials such as aggregates, carbides, chemicals, coal, diamonds, metal powders, minerals, pharmaceuticals, ores, pigments etc, invariably are supplied subject to whether or not the particle size is within a specified range or a permissible maximum or minimum tolerance in terms of percentage retained on or passing through a sieve or series of recognised international standards.

Sieve Shakers Overview

17

Inclyno 2 Sieve Shaker

Heavy duty floor mounted sieve shaker fitted with a digital timer. It is essential that the maximum sieving area is available at all times to allow particles to pass through the apertures. To provide this, the shaker uses two essential movements; gyratory and jolting, to spread the test material over the entire surface and breaking down any agglomerates in the powder, eventually clearing the sieve apertures. The Pascall Inclyno Sieve Shaker with its double gyratory and jolting action is noted for the accuracy of the sieve analysis of powdered material. The Inclyno has become a standard unit in many Testing Stations, Government Laboratories and Research Associations due to the reliable and consistent results obtained. Indeed, the particle size is often specified to an analysis determined by an Inclyno. The table of the Inclyno on which the sieves are clamped is always inclined to the axis of the machine. The table does not rotate but moves in a gyratory motion. This movement spreads the material over the entire surface area of the mesh of each sieve in turn. The movement is limited to the surface area of the mesh and the powder is not thrown high against the inner walls of the sieves.

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 20: Pascall_catalogue - CAPCO

Sieve Shakers

18

Machines Sieve Diameter 100 mm or 3” 200 mm or 8” 300 mm or 12”

Model 1 15 12 -

Model 2 - 14 7

Model 3 - 14 7

450 mm or 18” -

-

5

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Model 1 Model 2

Model 3

Page 21: Pascall_catalogue - CAPCO

Sieves Sieves

Test sieves need to be of good quality as particle sizes are an important element of many test procedures. We manufacture our own Capco test sieves, and for those of you who are familiar with Endecott sieves, we still supply those too if you so wish. Diameters stocked are 200mm and 300mm. Imperial sizes, 100mm and 450mm diameter are available to order. Standards BS 410 EN 933-2 ISO 565 ISO 3310-1 ISO 3310-2

Overview

19 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 22: Pascall_catalogue - CAPCO

Triple Roll Mills Overview

20

Model 1

Model No. 1 is driven is by a 180W motor wound for 220/240-1-50Hz (other windings are available) through a totally enclosed transmission consisting of vee belt, roller chain and gear train driving the rolls at the approximate different speeds of 45rpm back roll, 126rpm centre roll and 180rpm front roll. The motor is wired to an inbuilt mains inlet connector via an interlocking on-off switch carrying an anti-nip bar preventing accidental access to gap between the centre and back rolls. The two outer rolls adjust to the centre roll by four control knobs (two for back and two for front roll adjustment) allowing roll settings to be varied from fully open to close roll contact. When selected, the gaps are positively maintained and heavy roll pressure can be applied. The gaps selected are unaffected by the tendency of some materials, such as heavy viscous inks, to thrust the rolls apart. Model No. 2 is fitted with spring-located guide cheeks locating on the end faces of the back and centre rolls, allowing the full width of the rolls to be used. The drive of this model is by a 750W motor wound for 415-3-50Hz (other windings are available) through a totally enclosed transmission consisting of vee belts and a roller chain drive to gear train driving the rolls at the approximate different speeds of 33rpm back roll, 70rpm centre roll and 149rpm front roll. The mill is fitted with mains isolator, push-button starter, quick action cut-out button, and an electrically interlocked anti-nip guard between centre and back roll to guard against accidental access.

Pascall Triple Roll Mills are used to wet and disperse solids in liquid media, particularly viscous media. The mills process and refine a wide variety of materials such as ceramic colours, chocolate, cosmetic creams and lipstick mass, pharmaceutical ointments, paints and printing inks (including silk screen) and are ideal for laboratory use or for small scale production. Pascall Triple Roll Mills are available in two models, No. 1 which is bench mounting and No. 2 which is free standing. The output obtainable from either mill depends upon factors such as the viscosity and density of the material to be processed and the gaps selected between the rolls. For example, with material of average viscosity and density and with the rolls set at say 50 microns (0.002”) between back and centre rolls and say 25 microns (0.001”) between centre and front rolls, the possible output from No. 1 model is about 2 litres (1/2 gallon) and No. 2 model about 7 litres (1 1/2 gallons) per hour. The closer the rolls are set the lower the output and the wider the setting the greater the output.

Machines Picture Model No. Description

1 • Bench mounting • Choice of hardened steel, stainless steel or porcelain rolls. • Rolls 51mm in diameter. Front roll 108mm long, centre and back rolls

92mm long • Possible output approx. 2 litres per hour • Bench space approx: 482 x 353 x 356 (h) mm

2 • Free standing • Choice of hardened steel or stainless steel rolls either solid, or hollow

equipped with inlet & outlet for hot or cold water supply • Electrical cartridge type heaters available • Possible output 7 litres per hour • Rolls 89mm in diameter. Front roll 152mm long, centre and back rolls

127mm long • Sleeve type, self lubricated bearings on all rolls • Spring located guide cheeks • Stainless steel apron, easy to take off renewable stainless steel scraper

blade

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 23: Pascall_catalogue - CAPCO

Triple Roll Mills

21 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 24: Pascall_catalogue - CAPCO

Triple Roll Mills

22 CAPCO TEST EQUIPMENT LTD,

RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

With electric cartridge heaters Part Code Description Model Code Weight (kg)

TRIPRMILL2EHS Hollow steel rolls 1228-ES-C 190

TRIPRMILL2EHSS Hollow stainless steel rolls 1228-ESS-C 190

Machines Model Part Code Description Model Code Weight (kg)

1 TRIPRMILL1 Hardened steel rolls 1086-S-A 35

TRIPRMILL1P Porcelain rolls 1086-P-A 35

TRIPRMILL1S Stainless steel rolls 1086-SS-A 35

2 TRIPRMILL2S Solid hardened steel rolls 1228-S-C 190

TRIPRMILL2SS Solid stainless steel rolls 1228-SS-C 190

TRIPRMILLWHS Hollow steel rolls 1228-HSS-C 190

TRIPRMILL2WHSS Hollow stainless steel rolls 1228-HS-C 190

With water-cooled/heated rolls Part Code Description Model Code Weight (kg)

Part Code Description Model Code Weight (kg)

Accessories

TRIPRMILLPHOP Polypropylene feed hopper 1228-019 -

Page 25: Pascall_catalogue - CAPCO

Winnower & Cocoa Breaker

Overview

23

Machines

The System consists of an electrically driven cocoa breaker that cracks the whole bean – raw or roasted – and a pneumatic air-flow winnower that separates the broken shells from the nibs. Both units are compact and lightweight for use on a workbench or in the laboratory. Used together, they can achieve results in a few minutes compared with the labour intensive hand cutting method that can take up to 30 minutes. Not only is the system much faster, but it gives consistent results time after time. Any size of sample can be treated from a few beans to a small batch run.

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Machines Partcode Description Weight (kg)

COCOABREAKER110-1-60 Limprimita Cocoa Breaker 110volt 60Hz 1 Phase 36

COCOABREAKER240-1-50 Limprimita Cocoa Breaker 240volt 50Hz 1 Phase 36

COCOABREAKER415-3-50 Limprimita Cocoa Breaker 415volt 50Hz 3 Phase 36

COCOAWINNOW Cocoa Winnower 240volt 50Hz 1 Phase 7

Page 26: Pascall_catalogue - CAPCO

Conversion Tables

24

CAPACITY, VOLUME LENGTH 1 m3 = 1.30795 yd3 1 m =1.0936 yard 1 dm3 (litre) =0.03531 ft3 =3.281 ft =1.7605 pint =39.370 in =0.21997 imp gal 1 km =0.6214 mile =0.2642 US gal 1 yard =0.9144 m 1 cm3 (ml) =0.06102 in3 1 ft =30.48 cm =0.0352 fl oz 1 in =25.4 mm 1 yd3 =0.76455 m3 1 mile =1.6094 km 1 ft3 =28.3168 dm3 1 in3 =16.3871 cm3 MASS 1 us gal =4.54609 dm3 1 gal =3.78541 dm3 1 kg =0.02205 cwt 1 pint =0.56826 dm3 =2.20462 lb 1 fl oz =28.4131 cm3 1g =0.03527 oz 1t =1000 kg DENSITY =1.102311 ton 1 cwt =45.35924 kg 1 kg/m3 =1.686 lb/yd3 1 lb =0.45359 kg 1 g/cm3 =62.4280 lb/ft3 1 oz =28.349g 1 ton/yd3 =1328.94 kg/m3 1 lb/yd3 =0.593 kg/m3 PRESSURE, STRESS 1 lb/in3 =27.6799 g/cm3 1 Pa (N/m2) =0.01 mbar ENERGY =0.000145 lbf/in2 1 kPa (kN/m2) =0.01 kgf/cm2 1 MJ =0.277778 kWh =10 mbar 1 J =0.737562 ft lbf =20.885 lbf/ft2 1 kgf/m =9.80665 J =0.2953 in Hg2 1 Btu =1.0545 kJ 1 MPa =10.2 kgf/cm2 1 lbf/in2 (psi) =0.07031 kgf/cm2 FORCE =6.89476 kPa 1 lbf/ft2 =47.8803 Pa 1 N =0..010197 kgf 1 ton/ft2 =1.094 kgf/cm2 =0.224809 lbf =107.252 kPa 1 kN =1000 N 1 bar =100 kPa =101.971 kgf =14.5038 lbf/in2 =224.809 lbf 1 mbar =100 Pa =0.101971 t =0.0145038 lbf/in2 1 kgf =9.80665 N 1 atm =101.325 kPa =2.20462 lbf =14.6959 lbf/in2 1 mm Hg (torr) =133.322 Pa

=0.01934 lbf/in2 1mm H2 O =9.80665 Pa

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 27: Pascall_catalogue - CAPCO

Conditions of Sale

25

1. Acceptance - Every Contract of Sale and business transaction is subject solely to the following conditions, and no variation or alteration to these conditions shall be made unless expressly agreed with our written consent. These Terms supersede any such terms previously sent by either party. 2. Prices - All quoted and printed prices for goods are ex-works unless specified to the contrary, and are subject to alteration without notice. We reserve the right to invoice goods at our prices and at the VAT rates ruling at the date of despatch. Prices are exclusive of installation and commissioning unless specified to the contrary. 3. Quotations & Invoices - We reserve the right to correct any accidental errors or omissions on all quotations and invoices. Where all factors governing the price of the goods are under our direct control, we will unless stated hold quoted prices firm for a period of 30 days. 4. Orders - No order shall be binding on us unless accepted by us in writing 5. Delivery - Every effort will be made to adhere to delivery dates, but we shall accept no liability whatsoever to delays in deliv-ery irrespective of the cause, nor for delays in delivery due to circumstances beyond our control. Claims for errors or short-ages will not be entertained unless notified to us within 3 days of receipt of goods. 6. Amendments or cancellations - Amendments to any order will only be accepted by prior agreement. Orders cancelled be-fore delivery will be subject to a cancellation fee. Orders cancelled after delivery will be subject to a cancellation fee and in addition the customer will be expected to pay for all packing, freight, carriage and insurance costs for both the original deliv-ery and the return to Capco's premises. 7. Warranty and responsibility - Subject to the compliance to all installation, use, storage, maintenance and operating instruc-tions, we will repair or replace at our discretion any goods manufactured by ourselves in respect of defects arising solely from faulty materials or workmanship, provided they are returned carriage paid to us within 12 months from the original date of despatch from our premises. In the case of goods or parts not manufactured by us we will pass on to the customer the benefit of any guarantee or warranty received by us from the manufacturer in respect thereof insofar as such guarantee or warranty shall be capable of assignment. 8. Repairs - We are not responsible for damage occurring in transit to goods sent to us for repair or examination. When no order has been placed for the repair or examination we may charge for time involved in the preliminary examination and the reassembly of any article. Any goods returned for repair should be sent carriage paid, and clearly labelled with the senders name and address, and should include a letter detailing the work required. 9. Drawings & Sketches - We reserve the right to charge for the preparation of all drawings or sketches prepared for the submission of quotations or orders and all such drawings or sketches will remain our property. 10. Catalogues, Leaflets, etc. - Illustrations and descriptions of goods in our catalogues and any other literature are believed to be correct at the time of going to press. However with our policy of continuous improvement and development of our prod-uct range, illustrations, descriptions and specifications are subject to change without notice. 11. Copyright - The contents and arrangements of all catalogues and any other literature published by us are protected by copyright and may not be reproduced or used in whole or in part without our written permission. 12. Property and risk - The goods shall remain our property until the price has been discharged in full. The price shall not be deemed to be discharged in full until such a time that all funds, cheques, etc., have been cleared in our bank. The risk in goods shall pass on delivery to the purchaser. 13. Damage or loss in transit - Any claims for damage or loss in transit must be notified to us in writing within 3 days of re-ceipt of the goods. 14. Insurance - If requested by the purchaser or considered necessary by us we will effect insurance which will be charged on the invoice. We shall not be liable for failure to insure unless insurance was requested by the purchaser. If we effect insur-ance we shall be under no liability to take proceedings for recovery of any loss or damage and shall be limited to the amount received by us or the value of the goods, whichever is the less, from which deduction may be made for expenses. 15. Terms of payment - Payment for all orders shall be either cash with order or cash on delivery unless otherwise agreed. Credit terms will only be offered to agreed credit customers. Payment in this case will be 30 days from the date of Invoice. Accounts must be kept within the agreed credit limit. All invoice queries to be advised to Capco within 5 working days from the date of Invoice.

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Page 28: Pascall_catalogue - CAPCO

Conditions of Sale (cont)

26

Contact Us

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

CAPCO TEST EQUIPMENT LTD, RIVERSIDE VIEW, WICKHAM MARKET, WOODBRIDGE, SUFFOLK, IP13 OTA UK

TEL: 01728 747407 FAX: 01728 747599

WEB: WWW.CAPCO.CO.UK E-MAIL: [email protected]

Capco Test Equipment Riverside View

Wickham Market Suffolk

IP13 0TA United Kingdom

+44 (0)1728 747407

+44 (0)1728 747599

[email protected]

www.capco.co.uk

16. Applicable law - These conditions and any contract, relationship, agreement or arrangement shall be subject to and con-strued in accordance with English Law and the purchaser hereby submits to the jurisdiction of the English Courts. 17. No assignment - The customer may not assign to a third party the benefit or burden of any contract without our consent in writing. 18. Interest - In the event that an account becomes overdue we reserve the right to charge interest for any or all of the pe-riod which the account remains overdue, at our discretion, and at the rate of 8% per annum above the base rate of Lloyds Bank plc. No written notice of this will be necessary. 19. Legal costs - We reserve the right to charge any legal or other costs incurred in placing any outstanding accounts into the hands of our solicitors including any costs and disbursements charged to us on a solicitor and own client basis. Capco Test Equipment Ltd – 2005