Multiconn Multiconn Srl Srl PORSCHE PCM2.1 PORSCHE PCM2.1 www.dasdvbt.com www.dasdvbt.com Installation and User Manual Installation and User Manual ver.1.0 ver.1.0 [to integrate with the user manual of DAS M32/M44] [to integrate with the user manual of DAS M32/M44] Fiber Optic Fiber Optic
8
Embed
Multiconn Srl PORSCHE PCM2.1 Installation and User Manual ver.1.0 [to integrate with the user manual of DAS M32/M44] [to integrate with.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Multiconn SrlMulticonn Srl
PORSCHE PCM2.1PORSCHE PCM2.1
www.dasdvbt.comwww.dasdvbt.com
Installation and User Manual Installation and User Manual ver.1.0ver.1.0 [to integrate with the user manual of DAS M32/M44][to integrate with the user manual of DAS M32/M44]
Fiber OpticFiber Optic
Multiconn SrlMulticonn Srl 2
2. Disconnect the original Fiber Optical cable (fig.4)(fig.4) from one of the original multimedia accessories inside the car (DVD, GPS, Amplifier, etc…) and match it directly to DASDAS®® fiber optic female connector of the harness on equipment (fig.5)(fig.5).
44
44 55
Installation PCM 2.1:Installation PCM 2.1:
PCM 2.1PCM 2.1
1. To install the DASDAS®® receiver, refer to the specific user manual;
Warning on the connection of the power supply cableWarning on the connection of the power supply cable::
- RED wire (fig.3) must be RED wire (fig.3) must be DISCONNECTEDDISCONNECTED.. The switch (ON/OFF) of the receiver will be controlled by the Fiber-Optic activityThe switch (ON/OFF) of the receiver will be controlled by the Fiber-Optic activity
- YELLOW wire (fig.1)(fig.1) must be connected to the +12V permanent/battery- BLACK wire (fig.2)(fig.2) must be connected to the GND.
Power supply cable 11
22
33
3. Match the two other connectors of DASDAS®® harness (fig.6)(fig.6) respectively inside the original accessory (fig.7)(fig.7) and the other one inside DASDAS®® receiver (fig.8)(fig.8).
4. Connect one of the 3 DASDAS®® Video-OUT (fig.8)(fig.8) trough the adapter cables on equipment (fig.9) and the needed accessory (DCABFK-RCA (fig.9) and the needed accessory (DCABFK-RCA in fig.9.1)in fig.9.1) with the Video-IN on the Head Unit (fig.10) (fig.10) by the green Fakra connector.
Multiconn SrlMulticonn Srl 3
77 77 88
66
55
88
99
88
99.1.1 99
PCM 2.1PCM 2.1
Multiconn SrlMulticonn Srl 4
DASDAS Video-OUT
WARNING: if the Head Unit module has not the greengreen fakra fakra connector, the car cannot accept an original or aftermarket TV tuner
The PCM2.1 Head Unit module (fig.10)(fig.10).
1010
99.1.1
Video-IN
PCM 2.1PCM 2.1
User Manual:User Manual:
Multiconn SrlMulticonn Srl 5
To enter in DASDAS TV tuner press AVAV.
WARNING:WARNING: For the basic settings such as color, contrast, brightness and format, please refer to the menu of the car For the basic settings such as color, contrast, brightness and format, please refer to the menu of the car and make sure that the format is congruent with the set menu on the DAS.and make sure that the format is congruent with the set menu on the DAS.
Previous ChannelPrevious Channel(LEFT)(LEFT)
Next ChannelNext Channel(RIGHT)(RIGHT)
PCM 2.1PCM 2.1
Multiconn SrlMulticonn Srl 6
Remote Control Functions:Remote Control Functions: