Link Latch to “Edge Latch” Conversion - wrprodrill.com · Link Latch to “Edge Latch ... Part Number Decription Quantity 100451 Latch Pivot Pin 1 100450 Latch Spring 1 100467

Link Latch to “Edge Latch” Conversion

Summary

1. Safety first

2. Tools required

3. Parts required for N & H conversions

4. Link Latch parts no longer required N & H

5. Conversion instructions



Safety First ! Please wear safety glasses

Tools Required:


Tools Required:

1. Drillers Edge Drift Pin Tool (part# 100666) for removal and installation of ½” diameter Latch Retracting Pin.

2. Drillers Edge Drift Pin Tool (part#100877) for removal of ½” diameter Latch Pivot Pin.

3. Hammer

4. Socket wrench, socket 9/16” (14mm), extension 4” (100mm).


Drillers Edge Parts Required – N Size:


Drillers Edge Parts Required – N Size:

Part Number Decription Quantity

100451 Latch Pivot Pin 1

100450 Latch Spring 1

100467 Latch N 2

100449 Latch Retracting Pin 2


Drillers Edge Parts Required – H Size:


Drillers Edge Parts Required – H Size:

Part Number Decription Quantity

100484 Latch Pivot Pin 1

100450 Latch Spring 1

100496 Latch H 2

100483 Latch Retracting Pin 2


N - Link Latch Parts No Longer Required:


N - Link Latch Parts No Longer Required: Part Number Description Quantity 3541932 Nyloc Bolt 3/8”-16UNC x ¾” 1 306022 Washer 1 3543812 Latch Compression Spring 1 306452 Links 2 104816 Latches 2 24548 Spring Pin ½” x 1 ½” 1 24305 Spring Pin ½” x 2” 2


H - Link Latch Parts No Longer Required:


H - Link Latch Parts No Longer Required: Part Number Description Quantity 3541932 Nyloc Bolt 3/8”-16UNC x ¾” 1 104953 Washer 1 3543619 Latch Compression Spring 1 306216 Links 2 104818 Latches 2 24305 Spring Pin ½” x 2” 1 24524 Spring Pin ½” x 2 3/4” 2


Step 1: Remove spearhead point and base by driving out ½” x 2” spring pin – use Drillers Edge drift pin tool 100666.


Step 2: Use 9/16” (14mm) ratchet, socket and

extension to remove 3/8” Nyloc bolt, washer and spring


Step 3: Remove ½” x 2” spring pin using drift pin 100666, move latch retracting case to lower position, swing latches out and remove links.


Step 4: Remove latch retracting case.


Step 5: Using drift pin 100666 remove ½” x 1 ½” spring pin and remove link latches.


Step 6: Seat latch retracting case, place spring into slot and mount latches together


Step 7: Holding latches and spring together, insert Edge Latches (entering on an angle) as shown into the base of the upper latch body.


Step 8: Position latch retracting case as shown and use drift pin 100877 to align latch pivot holes.


Step 9: Hold drift pin 100877 in position during hammering to avoid jamming. Spring pin slot is best in downward position to avoid latch pivot hole damage during loading


(Lip Down)

Step 10: Latch pivot spring must be centered in upper latch body to avoid jamming of latch retracting case.


Step 10: Latch pivot spring must be centered in upper latch body to avoid jamming of latch retracting case.


Step 11: Seat latch retracting case, fold in Edge Latches and use drift pin 100666 to align and install new ½” x 2” latch retracting spring pin – slot down.


Step 12: Install spearhead point and base using drift pin 100666 to align and install latch retracting spring pin.

Link Latch to EdgeLatch Conversion

For technical support please contact: Steven Boesche (Tel: +1 705 4911 007) [email protected] John Daniels (Tel: +1 705 493 0359) [email protected] Richie Gushulak (Tel: +1 705 493 6651) [email protected] www.drillersedge.com


Link Latch to “Edge Latch” Conversion - wrprodrill.com · Link Latch to “Edge Latch ... Part Number Decription Quantity 100451 Latch Pivot Pin 1 100450 Latch Spring 1 100467

Documents