KLS8080I IPS Opto-isolated Sinusoidal BLDC V1.9

Kelly KLS8080I/IPS Sinusoidal Brushless Motor Controller User’s Manual V 1.9

Kelly KLS8080I/IPS MotorController User’s Manual

Rev.1.9Dec.2016

KLS72501-8080I KLS72601-8080I KLS72701-8080I

KLS96501-8080I KLS96601-8080I KLS12201-8080I

KLS12301-8080I KLS14201-8080I KLS14301-8080I

KLS14401-8080I

KLS72501-8080IPS KLS72601-8080IPS KLS72701-8080IPS



KLS14401-8080IPS


1

Contents

Chapter 1 Introduction..............................................................................................21.1 Overview..............................................................................................................................2

Chapter 2 Features and Specifications.................................................................32.1 General functions............................................................................................................... 32.2 Features...............................................................................................................................42.3 Specifications......................................................................................................................52.4 Name Regulation................................................................................................................5

Chapter 3 Wiring and Installation...........................................................................63.1 Mounting the Controller.....................................................................................................63.2 Connections........................................................................................................................ 83.3 Installation Check List......................................................................................................13

Chapter 4 Programmable Parameters................................................................ 144.1 Step 1.................................................................................................................................144.2 Step 2.................................................................................................................................194.3 Step 3.................................................................................................................................20

Chapter 5 Maintenance..........................................................................................215.1 Cleaning.............................................................................................................................215.2 Configuration.....................................................................................................................22

Table 1: ERROR CODES......................................................................................... 23

Contact Us:..................................................................................................................24


2

Chapter 1 Introduction1.1 Overview

This manual introduces the Kelly sinusoidal wave brushless BLDC motorcontrollers’ features, their installation and their maintenance. Read the manual carefullyand thoroughly before using the controller. If you have any questions, please contact thesupport center of Kelly Controls, LLC.

Kelly’s programmable motor controllers provide efficient, smooth and quiet controlsfor electric motorcycles, golf carts and go-carts, as well as industrial motor control. It is mainlysupposed to solve noise problems of BLDC motor driving application. KLS controller can notsupport sensorless brushess motor for now.Compared to the traditional trapezoidal waveformcontrol technology, this technique based on sinusoidal wave driving technology to reduce theoperation noise and 1/3 switching loss, which well meets the noise reduction and efficiencyrequirements in the application of DC brushless motor. It uses high power MOSFET’s and,SVPWM and FOC to achieve efficiencies of up to 99% in most cases. A powerfulmicroprocessor brings in comprehensive and precise control to the controllers. It also allowsusers to adjust parameters, conduct tests, and obtain diagnostic information quickly andeasily.People can program the KLS controller on PC software and Android App.There is onemore choice for customers to program KLS controller now.The APP software is based on Tabletwith Android OS.Customers may add a Z-TEK USB to RS232 cable for programming KLScontroller if they want to use Android Tablet.

Both PC software and Android APP can provide one screen to monitor the controllerparameters.Sometimes people can use a small Android Tablet as display device.

KLS8080I/IPS is designed by opto-isolated technology.We specify 8-30V for powersupply which must be isolated from main battery pack B+/B-.You may use an isolatedDCDC converter or a separate 12V battery for power supply.KLS8080I is supposed towork with BLDC motor with hall sensors.KLS8080IPS can work with brushless motorwith Sin/Cosin speed sensors.

KLS8080I/IPS controller included the fuse and shunt on the case.


3

Chapter 2 Features and Specifications2.1 General functions(1) Extended fault detection and protection. Customers can read the error code in PC

software or Android Tablet also.(2) Monitoring battery voltage. It will stop driving if the battery voltage is too high and it

will progressively cut back motor drive power as battery voltage drops until it cutsout altogether at the preset “Low Battery Voltage” setting.

(3) Built-in current loop and over current protection.(4) Configurable motor temperature protection range.(5) Current cutback at low temperature and high temperature to protect battery and

controller. The current begins to ramp down at 90℃ case temperature, shutting down at100℃.

(6) The controller keeps monitoring battery recharging voltage during regen braking.(7) Maximum reverse speed and forward speed can be configured between 20% and

100% respectively and separately.(8) A 4pin connector to RS232 port and a Z-TEK USB to RS232 cable allows for

configuration, programming and software upgrades using the tablet which must bebased on Android OS now.People can do the same things on PC software by usinga standard USB to RS232 cable instead.

(9) Provision of a +5 volt and +12 volt output to supply various kinds of hall sensors.(10) 5 switch inputs which are activated by connection to 12V. Default to throttle switch,

brake switch,reversing switch,forward switch and Boost switch.(11) 3 analog 0-5V inputs that default to throttle input,Brake analog input and motor

temperature input(12)Copy signal of one of sensors.(13)Configurable boost switch. Enables the maximum output power achievable if the

switch is turned on.The effect is the same as full throttle position even if you don’tturn throttle at all.

(14) 12V brake switch input used different port from motor temperature sensor.You can useboth brake switch and motor temperature sensor functions at the same time on the latestversion.Pin 25 is 12V brake switch input port.Pin1 is motor temperature sensor input port.

(15)Optional joystick throttle. A bi-symmetrical 0-5V signal for both forward andreversing.

(16)Configurable motor over-temperature detection and protection with therecommended thermistor KTY84-130/150 or KTY83-122.

(17) 3 hall position sensor inputs. Open collector, pull up provided.Sin/Cosin Speedsensors inputs.

(18) Brake analog regen mode.This regen mode doesn't need brake switch to supportany more.Only available from software version 0106 or advanced version.KLScontroller can not support reflashing firmware by default.

(19) Enhanced regen brake function. A novel ABS technique provides powerful andsmooth regen.The regen can happen at any speeds until zero speed.


4

(20)Cruise control.Only can be activated in reversing direction.(21) KLS-8080I/IPS can support Broadcast type CAN bus function.It is 250Kbps.By

default,KLS-8080I/IPS controller includes CAN bus function.(22)Bluetooth function.Required a small Bluetooth converter which needs to be purchased in

addition from our website.This small converter is only useful for KLS controller.Caution! The regen is not a safe function.Usually you may use the mechanical brake.

2.2 Features1) Intelligence with powerful microprocessor.2) Synchronous rectification, ultra low drop, fast SVPWM and FOC to achieve very high

efficiency.3) Electronic reversing.4) Voltage monitoring on 3 motor phases, bus, and power supply.5) Voltage monitoring on voltage source 12V and 5V.6) Current sense on all 3 motor phases.7) Current control loop.8) Hardware over current protection.9) Hardware over voltage protection.10) Configurable limit for motor current and battery current.11) Low EMC.12) Battery protection: current cutback, warning and shutdown at configurable high and low

battery voltage.13) Rugged aluminum housing for maximum heat dissipation and harsh environment.14) Rugged high current terminals, and rugged aviation connectors for small signal.15) Thermal protection: current cut back, warning and shutdown on high temperature.16) Controller can do auto_Identification angle for different Sine/Cosine Speed sensors.Can

adjust the zero-crossing point and signal amplitude to match different Sine/Cosine speedsensors.

17) Configurable high pedal protection: the controller will not work if high throttle is detected atpower on.

18) Current multiplication: Take less current from battery, output more current to motor.19) Easy installation: 3-wire potentiometer will work.20) Standard PC/Laptop computer to do programming.There is one more choice for customers

to program KLS controller.Standard Tablet with Android OS to do programming.Need aZ-TEK USB TO RS232 cable for connecting the controller to App program in Tablet.

21) User program provided. Easy to use. No cost to customers.22) Support motors with any number of poles.23) Up to 70,000 electric RPM standard. (Electric RPM = mechanical RPM * motor pole

pairs;Motor pole pairs=Motor poles/2).


5

2.3 Specifications•Frequency of Operation: 10KHz or 20kHz.•Standby Battery Current: < 0.5mA.•5V or 12V Sensor Supply Current: 40mA.•Controller supply voltage range: PWR, 8V to 30V for pin7 and pin6 which must be isolatedfrom main battery pack B+/B-.•Supply Current, PWR, 30mA Typical.•Configurable battery voltage range, B+. Max operating range: 18V to 1.25*Nominal Voltage.•Standard Throttle Input: 0-5 Volts(3-wire resistive pot), 1-4 Volts(hall active throttle).•Throttle Input: 0-5 Volts. Can use 3-wire pot to produce 0-5V signal.•Main Contactor Coil Driver<2A.•Full Power Operating Temperature Range: 0℃ to 70℃(MOSFET temperature).•Operating Temperature Range: -40℃to 100℃ (MOSFET temperature).•Max Battery Current :Configurable.

2.4 Name RegulationThe name regulation of Kelly KLS motor controllers:KLS 8080I/IPSKLS:Kelly BLDC motor controller based on sinusoidal waveform.KLS8080I is supposedto work with brushless motor with three hall sensors while KLS8080IPS can work withSin/Cosin speed sensors.There are +5V,Sin,Cosin and GND I/O ports for brushless motorwith Sin/Cosin speed sensors.I:KLS8080I is designed by opto-isolated technology.We specify 8-30V for power supplywhich must be isolated from main battery pack B+/B-.

Kelly KLS8080I/IPS Sinusoidal Brushless Motor Controller

Model 60 secondsCurrent(Amp)

ContinuousCurrent(Amp) Voltage(Volt)

KLS72501-8080I/IPS 500 200 24-72KLS72601-8080I/IPS 600 240 24-72KLS72701-8080I/IPS 700 280 24-72

Model 30 secondsCurrent(Amp)

ContinuousCurrent(Amp) Voltage(Volt)

KLS96501-8080I/IPS 500 200 24-96KLS96601-8080I/IPS 600 240 24-96KLS12201-8080I/IPS 200 80 24-120KLS12301-8080I/IPS 300 120 24-120KLS14201-8080I/IPS 200 80 24-144KLS14301-8080I/IPS 300 120 24-144KLS14401-8080I/IPS 400 160 24-144


6

Chapter 3 Wiring and Installation3.1 Mounting the Controller

The controller can be oriented in any position which should be as clean and dry as possible,and if necessary, shielded with a cover to protect it from water and contaminants.

To ensure full rated output power, the controller should be fastened to a clean, flat metalsurface with four screws. Applying silicon grease or some other thermal conductive material tocontact surface will enhance thermal performance.

Proper heat sinking and airflow are vital to achieve the full power capability of the controller.The case outline and mounting holes’ dimensions are shown in Figure 1.

Figure 1:KLS72501-8080I/IPS—→KLS14301-8080I/IPS mounting holes’ dimensions (dimensionsin millimeters)


7

Figure 1:KLS14401-8080I/IPS mounting holes’ dimensions (dimensions in millimeters)


8

3.2 Connections3.2.1 Pin definition of KLS8080I/IPS Controller

Figure 2:KLS8080I waterproof connector

DJ7091Y-2.3-11 Pin Definition(14) REV_SW: Reverse switch input. Orange(6) RTN: Signal return or power supply return. Black(12) FWD: Forward switch White(11) 12V:12V Source Red(25) 12V brake switch. Yellowish(9) Relay: Main contactor driver. Blue(33)CAN-H:Green(7) PWR: Controller power supply (input). Pink(34)CAN-L:Dark Gray


9

DJ7091Y-2.3-21 Pin Definition(15) Micro_SW: Throttle switch input. Gray(3) Throttle: Throttle analog input, 0-5V. Dark Green(1) Temp: Motor temperature sensor input. Raddle.(20) RTN: Signal return. Black(8) Meter: Copy signal of hall sensors. Dark Blue(4) 5V: 5V supply output, <40mA. Purple(2) Brake_AN：Brake variable regen or Boost function. Brown

DJ7061Y-2.3-21 Pin Definition(21) RTN:Signal return. Black(5) 5V: 5V supply output,<40mA.Purple(18) Hall A: Hall phase A. Yellow 【This is Sine signal input on KLS8080IPS】(17) Hall B: Hall phase B. Dark Green 【This is Cosine signal input on KLS8080IPS】(16) Hall C: Hall phase C. Dark Blue【There is no hall C signal input on KLS8080IPS】

Notes:1. All RTN pins are internally connected.2. Meter function is to copy either of hall sensors.3. Switch to 12V is active. Open switch is inactive.

Caution:• Do not apply power until you are certain the controller wiring is correct and has beendouble checked. Wiring faults will damage the controller.• Ensure that the B- wiring is securely and properly connected before applying power.• The preferred connection of the system contactor or circuit breaker is in series with the B+line.• All contactors or circuit breakers in the B+ line must have precharge resistors across theircontacts. Lack of even one of these precharge resistors may severely damage the controllerat switch-on.


10

3.2.2 Standard Wiring of KLS8080I/IPS Controller

Figure 3: KLS8080I controller standard wiring


11

Figure 4: KLS8080IPS controller standard wiring


12

3.2.3 Optional wiring of KLS8080I/IPS controllerThe 12V input signal of the pin supplies the second braking function of the controller.

Figure 5:Wiring of brake switch(12V): 12V is provided by external source.

Figure 6: Wiring of brake switch(12V): 12V is provided by KLS8080I controller on pin11

Figure 7: Wiring diagram for motor temperature sensor

NOTE:The motor temperature sensor and brake switch used the same I/O port on pin1.Bothfunctions can not be used at the same time.KLS controller can support KTY84-150 andKTY84-130 thermistors.


13

3.2.4 Communication PortA 4pin connector to RS232 port is provided to communicate with host computer for calibration and

configuration.

Figure 8: RS232 Interface on 4pin connector to RS232 converter

Figure 9：SM-4P connector for communication interface on KLS8080I controller

3.3 Installation Check ListBefore operating the vehicle, complete the following checkout procedure. Use LED code as

a reference as listed in Table 1.

Caution:• Put the vehicle up on blocks to get the drive wheels off the ground before beginning thesetests.

• Do not allow anyone to stand directly in front of or behind the vehicle during the checkout.• Make sure the PWR switch and the brake is off• Use well-insulated tools.


14

• Make sure the wire is connected correctly

• Turn the PWR switch on.

• The fault code will be detected automatically at restart.

• With the brake switch open, select a direction and operate the throttle. The motor should

spin in the selected direction. Verify wiring or voltage and the fuse if it does not. The motorshould run faster with increasing throttle. If not, refer to the Table 1 code, and correct thefault as determined by the fault code.

• Take the vehicle off the blocks and drive it in a clear area. It should have smooth

acceleration and good power.

Chapter 4 Programmable Parameters

KLS Configuration program allow users to set parameters according to the vehicle actualworking environment so as to be at its best.

The default parameters of the controller are not recommended for all applications. Makesure set the proper parameters before making any test to avoid danger.

Customers can do program on PC software or Android App.The Android Tablet isprefered.First of all,people need to do Identification angle function for KLS controller beforerunning the motor.The controller needs to be connected to batteries,motor and throttle beforeIdentification operation.That is to say,it is not enough to connect only power supply(PWR=pin7)to batteries for Identification Angle operation.

Please download the instruction how to use Identification angle function from our website.www.kellycontroller.com/support.php

4.1 Step 1(1)Low Volt: The min voltage of reporting this fault - Range 18~180

http://www.kellycontroller.com/support.php


15

Controller will not operate when battery voltage is near the value so as to protect battery.Suggestion: Set according to the practical situation.By default,it is set at 18V.

(2)Over Volt: The max voltage of reporting this fault - Range 18~180Controller will not operate when battery voltage is higher than the value so as to protect batteryand controller.Suggestion: Set according to the practical situation.Here is the max voltage for each model.72V controller:90V96V controller:120V120V controller:136V144V controller:180V

Controller Rated voltage Under Voltage Range (V) Over Voltage Range(V)72V 18~90 18~9096V 18~120 18~120120V 18~136 18~136144V 18~180 18~180

Figure 4.1

(3)Current Percent: Phase Current Percent. Range: 20~100Functional description: The max motor current is (The Value * Peak Current of the Controller).Suggestion: Factory default is 100%.

(4)Battery Limit: Battery Limit Current, Limit the max value of Battery Current. Range: 20~100Functional description: Set max battery current so as to protect battery. A lower value means alower battery output current and better protective effect. But excessively low value will affectacceleration.Suggestion: Factory default is 100%.

(5)Identification Angle: Please download the instruction to how to use Identification anglefunction from the website.www.kellycontroller.com/support.phpIf you can read 85 in Identification Angle item,that is to say,the system is stable andnormal.Please fill in 170 for Identification Angle item in user program.Thenplease click Write button in user program.Please wait a few seconds before restart the powersupply.You will see some info on Monitor screen after power supply isreset.If you see Reset error on the Monitor screen,that is to say,the auto_Identification isfinished.You can see 85 in the Identification Angle item again.And the controller willblink error code.This is normal.Please reset the power supply again.Then everything will befine.The motor is ready to be drived by the KLS controller.Range: 85 or 170,nothing else.


16

(6)TPS Low Err: Hall active pedal, if lower than the value, report the fault of TPS Type. Range:0~20(7)TPS High Err: Hall active pedal, if higher than the value, report the fault of TPS Type. Range:80~100As you may know,the output of hall throttle from Kelly is about from 0.86V to 4.2V.Our controller will report 3.3 error code if the output of hall throttle is below 0.5V or above 4.5Vby default.The controller will think the hall throttle is shorted or damaged if the output is beyond the rangefrom 0.5V to 4.5V.You can adjust the threshold voltage below or above 0.5V.The controller will report the 3.3 codeto protect the system according to different types of hall throttle.Because there are many different hall throttle suppliers in the world.The initial output can not bealways in the range of 0.5V to 4.5V.

But it doesn't make any differences if you choose 0-5V or 3-wire pot for the throttle type.That isto say,these two settings are only useful for hall active throttle or pedal when you chose throtletype at 2.

As the same goes,it is valid to adjust the high threshold voltage above 4.5V or below 4.5V.Usually the hall output voltage is 4.2V Max.If you adjust it to lower value which is near 4.2V,itmay trigger the error code in normal way.

(8)TPS Type: TPS Type, 1:0-5V 3-wire 0-5K pot,5K is normal,2K-20K can be used;2:Hall activethrottle or pedal. Range: 1~2

(9)TPS Dead Low: TPS Dead Zone Low. Range: 5~40Functional description: Set throttle effective starting pointSuggestion: Set according to the practical situation, factory default is 20%*5V=1.0V.

(10)TPS Dead High: TPS Dead Zone High. Range: 60~95Functional description: Set throttle effective ending pointSuggestion: Set according to the practical situation, factory default is 80%*5V=4.0V.

(11)Brake sensor type:Brake sensor type for brake variable regen mode:1:0-5V 3-wire 0-5K pot,5K is normal,2K-20K can be used;2:Hall active throttle or pedal. Range:1~2

(12)Brake sensor Dead Low: Brake sensor Dead Zone Low. Range: 5~40Functional description: Set throttle effective starting pointSuggestion: Set according to the practical situation, factory default is 20%*5V=1.0V.

(13)Brake sensor Dead High: Brake sensor Dead Zone High. Range: 60~95


17

Functional description: Set throttle effective ending pointSuggestion: Set according to the practical situation, factory default is 80%*5V=4.0V.

(14)Max output Fre: Max output frequency. Unit:HzFunctional description:It will affect the top speed of the motor.Suggestion: Set according to the practical situation, factory default is 1000Hz.Please don’t set it1000Hz above.

(15)Max Speed: Max Speed [rpm]. Range: 0~15000 By default,it is set at 4000.Softwareversion 0109 can support 15000RPM settings in user program.

(16)Max Fwd Speed %: The forward speed of the percentage of maximum speed. Range:20~100 By default,it is set at 100%(17)Max Rev Speed %: The reverse speed of the percentage of maximum speed. Range:20~100 By default,it is set at 100%

(18)PWM Frequency: Frequency of PWM operation. Unit:KHzFunctional description:20KHz is better for hub motor with strict quiet control.Suggestion: Set according to the practical situation, factory default is 20KHz.Please don’t set it20KHz above.Value Range:10KHz or 20KHz

(19)Start-up H-Pedal:Value range: Enable and DisableFunctional description: If enabled, the controller will detect the current pedal status at power up.If throttle got effective output, the controller will report fault and not operate.Suggestion: Set according to the practical situation, factory default is Enable.

(20)Brake H-Pedal:Releasing Brake High Pedal DisableValue range: Enable and DisableFunctional description: If enabled, the controller will detect the current pedal status whenrelease the brake. If throttle got effective output, the controller will report fault and not operate.Suggestion: Set according to the practical situation, factory default is Disable.

(21)NTL H-Pedal:Neutral position High Pedal Disable.Only useful when Three gears switchfunction is enabled.If enable,the controller will detect the current pedal position or signal When the switch is inneutral poistion.If the throttle got effective output signal,the controller will not operate and report fault code.Suggestion: Set according to the practical situation, factory default is Disable.

(22)Joystick function:


18

If enable,the controller can drive the motor on two directions without using any reversing switch.Just one single throttle can drive the motor on forward and reversing direction.The stick shift throttle firmware can be called wig-wag or joystick operation.It is only a softwarefunction.Usually It is useful for electric boat project.You still can use the common 0-5K pot or0-5V throttle for the controller.If you don't choose the joystick,you operated the throttle in thisway.The motor speed will increase when the throttle is from 0V to 5V.If you enable joystick for this controller in user program,you will start the motor from 2.5Vposition.2.6V to 5V is forward.2.4V to 0V is backward.2.4V to 2.6V is the throttle dead zone.Customers can adjust the throttle dead zone in userprogram also.Please note the common throttle will spring back to original position if you release the throttle.Suggestion:factory default is Disable.

(23)Three Gears switch:It is used for function of F-N-R control.Please check the wiring diagram in the manual for F-N-R control.Suggestion: Set according to the practical situation, factory default is Disable.(20-A)Three Gears SwitchValue range: Enable and DisableFunctional description: If enabled, the Forward switch will be activated. Please see figure 4.1.Suggestion: Set according to the practical situation, factory default is Disable.(20-B)Foot SwitchValue range: Enable and DisableFunctional description: If enabled,the foot switch will be activated.The controller will not acceptthe throttle signal if the foot switch is turned off. Please see figure 4.1.Suggestion: Set according to the practical situation, factory default is Disable.

Configuration Pin Status RunningStatusForward

Switch Foot Switch FWD_SW(12)

REV_SW(14)

Foot(15)

Enable Disable

OFF OFF x NeutralOFF ON x ReverseON OFF x ForwardON ON x Neutral

Disable Enable

x OFF OFF Can’t operatex ON OFF Can’t operatex ON ON Reversex OFF ON Forward

Disable Disable x OFF x Forwardx ON x Reverse

Note: X means can be on or offFigure 4.2


19

(24)Boost:If enabled,the controller will output max power for a while.Boost function is just full throttle position when you turn on boost switch even if the throttle is notoperated at all.The boost function is still based on limiting of the motor current and battery current settings inuser program.If disabled,the controller can provide brake sensor regen mode on the same pin as pin2.Insimple,boost and brake analog regen used the same pin as pin2.Suggestion: Set according to the practical situation, factory default is Disable.So the defaultfunction is brake variable regen mode.

(25)Foot switch:It is used for microswitch.If enabled,the controller will only accept the throttlesignal after received the valid foot switch signal.If there is no foot switch signal,the controller will ignore the throttle signal.Suggestion: Set according to the practical situation, factory default is Disable.

(26)Cruise Control:Value range: Enable and DisableIf enable,if you hold throttle at certain position about 3-4 seconds,the controller will get intoCruise control.The Cruise function can not be activated in reversing direction.Release throttle and turn the throttle again or turn on the brake switch will make the Cruisecontrol quit.Suggestion:factory default is Disable.

(27)Change Direction:If the direction is not what you expected after finish the Identification angle operation,please justchoose Change Direction item.Please click Write button to activate Change Direction function.The motor direction will be whatyou expected after the power supply is reset.Suggestion:factory default is Disable.

4.2 Step 2

(1)Motor Poles: Motor Poles, The pair pole number*2. Range: 2~128Suggestion: Set according to the real motor poles on the nameplate of the motor, factory defaultis at 8.

(2)Speed Sensor Type: Speed Sensor Type, 2:Hal, 3:Resolver, 4:Line Hall. Range: 2~4Different sensors type.By defualt,it is set at 2If you have a motor with 5V,Sin/Cosin,GND speed sensors,please choose it at 4.And pleaseinquire the KLS-8080IPS model before ordering.

(3)Resolver Poles: Resolver Poles, The pair pole number*2. Range: 2~32It is only used for the Resolver sensor type.


20

(4)Motor Temp Sensor: Motor Temp Sensor, 0：None,1:KTY84-130 or 150,2:KTY83-122.Range0-2High Temp Cut Out °C: Motor High Temp Cut Out, nominal value 130°C. Range: 60~170Resume ° C: Motor High Temp Resume Temp, nominal value 110° C.The controller willresume work when the motor temp is at 110 degrees inside. Range: 60~170

(5)Line Hall Zero:It is only useful when the speed sensor is at 4.Zero-Crossing point of Sine/Cosine linear hall sensors output signal.Usually the Sine/Cosinespeed sensor supplier provided sensors with 2.5V or 3.0V zero-crossing point.You can change it back between 2.5V and 3.0V if the motor can not run.Suggestion: Set according to the practical situation, factory default is 613(3.0V) for Mars1114/1115/1302/1304 from Motenergy company.Value Range:0-1023 maps 0-5V

(6)Line Hall Amplitude:The position signal based on Zero-crossing point.It is only useful whenthe speed sensor is at 4.For example,if the Line hall Amplitude is 1.1V,the signal output of Sine/Cosine sensors is from1.9V to 4.1V.(3-1.1=1.9V;3+1.1V=4.1V)Value Range:0-1023 maps 0-5V

(7)Line Hall High Err:It is only useful when the speed sensor is at 4.If the signal output of Sine/Cosine speed sensor is above this setting,the controller will reporthall error.Please adjust Line Hall High Err to a higher value to eliminate this error.Value Range:0-1023 maps 0-5V

(8)Line Hall Low Err:It is only useful when the speed sensor is at 4.If the signal output of Sine/Cosine speed sensor is below this setting,the controller will reporthall error also.Please adjust Line Hall Low Err to a lower value to eliminate this error.Value Range:0-1023 maps 0-5V

4.3 Step 3(1)RLS_TPS Brk %: RLS TPS Braking Percent, the percent of Releasing Pedal BRK in maxbraking. Range: 0~50This is used to adjust the regen current of releasing throttle regen mode type.The regen willhappen as long as the throttle is released completely.Factory set is 0

(2)NTL Brk %: NTL Braking Percent, the percent of Neutral Braking in max braking. Range:0~50Only useful when you enable Three gears switch in user program.The regen will happen when you turn F-N-R switch from Forward or backward to Neutralposition.Factory set is 0


21

(3)Accel Time: Accel Time, the time of TPS Torque from 0 to max, accuracy 0.1s, 5 is equal to0.5s. Range: 1~250Factory set is 10

(4)Accel Rls Time: Accel Release Time, the time of TPS Torque from max to 0, accuracy 0.1s.Range: 1~250Factory set is 1

(5)Brake Time: Brake Time, the time of Brake Torque from 0 to max, accuracy 0.1s. Range:1~250Factory set is 15

(6)Brake Rls Time: Brake Release Time, the time of Brake Torque from max to 0, accuracy 0.1s.Range: 1~250Factory set is 1

(7)BRK_SW Brk %: BRK_SW Braking Percent, the percent of BRK_SW in max braking. Range:0~50The brake switch regen mode.You have to turn on the brake switch after the throttle is releasedfor the regen to occur.Factory set is 10

(8)Brake Analog regen Brk%:It is used to adjust the max regen percentage of brake variableregen mode.This regen mode doesn't need brake switch to support any more for KLS controller.

(9)Torque Speed KP: Speed Percent Kp in Torque Mode. Range: 0~10000 Factory set is 3000Torque Speed KI: Speed Integral Ki in Torque Mode. Range: 0~500 Factory set is 80Speed Err Limit: Speed Error Limit in Torque Mode. Range: 50~4000 Factory set is 1000These three parameters are used for PID adjustment.If you think the acceleration performance is very very strong,please adjust them to a lower valuerespectively.

(10)Change Dir brake:Value range: Enable and DisableIt is only useful when you Enable the joystick function.If you want to get swift direction changing by using joystick function,you may enable Change Dirbrake item in user program.It will help the motor change the direction of motor quickly after you shift throttle from 0V to 5V,orfrom 5V to 0V.Suggestion:factory default is Disable.

Note: Thermistor is optional. Default to KTY84-130/150 or KTY83-122


22

Chapter 5 MaintenanceThere are no user-serviceable parts inside the controllers. Do not attempt to open the

controller as this will void your warranty. However, periodic, exterior cleaning of the controllershould be carried out.

The controller is a high powered device. When working with any battery powered vehicle,proper safety precautions should be taken that include, but are not limited to, proper training,wearing eye protection, avoidance of loose clothing, hair and jewelry. Always use insulatedtools.

5.1 CleaningAlthough the controller requires virtually no maintenance after properly installation, the followingminor maintenance is recommended in certain applications.• Remove power by disconnecting the battery, starting with battery positive.• Discharge the capacitors in the controller by connecting a load (such as a contactor coil,

resistor or a horn) across the controller’s B+ and B- terminals.• Remove any dirt or corrosion from the bus bar area. The controller should be wiped with a

moist rag. Make sure that the controller is dry before reconnecting the battery.• Make sure the connections to the bus bars, if fitted are tight. To avoid physically stressing

the bus bars use two, well-insulated wrenches.

5.2 ConfigurationYou can configure the controller with a host computer through either an RS232 or USB port.• Disconnect motor wiring from controller for configuring existing parameters in the user

program or Android APP. If this operation is too much extra job for you, please make surethe motor must be stopped before programming.

• The controller may display fault code, but it doesn't affect programming orconfiguration.But it will affect the Identification angle operation.Please try to eliminate theerror codes before Identification angle operation.

• Use a straight through RS232 cable or USB converter provided by Kelly to connect to ahost computer. Provide >+18V to PWR（for a 24V controller, provide >+8V）. Wire powersupply return(supply negative) to any RTN pin.

• KLS controller requires a 4pin connector to Kelly RS232 Converter to support thecommunication.And customers may need a Z-TEK USB cable for Tablet with Android OS.

Customers may download PC software or Android APP to program the controllerbefore running the motor.You may do Identification angle for brushless motor withhall sensors after running the software or Android APP.Every item in the


23

configuration program can show the explanation automatically when you click it.Caution:•Make certain that the motor is connected before trying to run Identification anglefunction in the configuration software.The controller needs to be connected tobatteries,motor and throttle before Identification operation.That is to say,it isnot enough to connect only power supply(PWR=pin7) to batteries forIdentification Angle operation.

•Configuration software will be regularly updated and published on the website. PleaseUpdate your Configuration Software regularly. You must uninstall the older versionbefore updating.•Please try to use Identify function for motor and hall sensors in the user program

Table 1: ERROR CODESBuzzer Error Codes

Code Explanation Solution1,1 ¤ ¤ Automatic error

identification1. Wrong wiring of motor phase line or hall.

Please suspend the motor when enableAuto-Identify function.

1,2 ¤ ¤¤ Over voltage error 2. Battery voltage is too high for the controller.Check battery volts and configuration.

3. Regeneration over-voltage. Controller will havecut back or stopped regen.

4. This only accurate to ± 2% upon Overvoltagesetting.

1,3 ¤ ¤¤¤ Low voltage error 1. The controller will clear after 5 seconds if batteryvolts returns to normal.

2. Check battery volts & recharge if required.1,4 ¤ ¤¤¤¤ Reserved2,1 ¤¤ ¤ Motor did not start Motor did not reach 25 electrical RPM within 2

seconds of start-up. Hall sensor or phase wiringproblem.

2,2 ¤¤ ¤¤ Internal volts fault 1. Measure that B+ & PWR are correct whenmeasured to B- or RTN.


24

2. There may be excessive load on the +5V supplycaused by too low a value of Regen or throttlepotentiometers or incorrect wiring.

3. Controller is damaged. Contact Kelly about awarranty repair.

2,3 ¤¤ ¤¤¤ Over temperature The controller temperature has exceeded 100℃. Thecontroller will be stopped but will restart whentemperature falls below 80℃.

2,4 ¤¤ ¤¤¤¤ Throttle error atpower-up

Throttle signal is higher than the preset ‘dead zone’ atPower On. Fault clears when throttle is released.

3,1 ¤¤¤ ¤ Reserved

3,2 ¤¤¤ ¤¤ Internal reset May be caused by some transient fault condition likea temporary over-current, momentarily high or lowbattery voltage. This can happen during normaloperation.

3,3 ¤¤¤ ¤¤¤ Hall throttle is openor short-circuit

When the throttle is repaired, a restart will clear thefault.

3,4 ¤¤¤ ¤¤¤¤ Angle sensor error 1.Speed sensor type error，customers may set thecorrect sensor type through user program or App.Please download how to use Identification functioninstruction from our website.2.Incorrect wiring.3.Speed sensor is damaged or defective.Or feedbacksignal is erratic.

4,1 ¤¤¤¤ ¤ Reserved4, 2 ¤¤¤¤ ¤¤ Reserved4, 3 ¤¤¤¤ ¤¤¤ Motor

over-temperatureMotor temperature has exceeded the configuredmaximum. The controller will shut down until themotor temperature cools down.

4, 4 ¤¤¤¤ ¤¤¤¤ Hall Galvanometersensor error

1.Hall galvanometer device is damaged inside thecontroller.This error code is only valid for KLS-8080I controller.

Customers may read error codes in PC software or Android Tablet

Contact Us:

Kelly Controls, LLC


25

Home Page:http://www.KellyController.com

Download user manual,instructions and user program:www.kellycontroller.com/support.php

E-mail:[email protected]

Phone:(01) 224 637 5092

http://www.kellycontroller.com

http://www.kellycontroller.com/support.php

mailto:[email protected]

KLS8080I IPS Opto-isolated Sinusoidal BLDC V1.9

Documents