This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60 Hz 150 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 15 kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTEROUT/ SUBWOOFER
DVD/CDSignal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=192 kHz 16 Hz to 88 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 95 dBWow and Flutter Less than measurable limit
SDCompatible File System FAT 32/16/12Capacity 8 Mbytes to 2 GbytesData Transfer Rate Maximum 10 Mbps
USBUSB Standards USB 1.1Data Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5V
TVColor System PAL/SECAMChannel Coverage VHF: Ch 2 - 12
UHF: Ch 21 - 69MONITOR
Screen Size 7 inch wide liquid crystal displayNumber of Pixel 336 960 pixels: 480 × 3 (horizontal) × 234 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PAL/SECAMAspect Ratio 16:9 (wide)
GENERALPower Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D): With trim plate and sleeve at-tached
Installation Size (approx.) 182 mm × 111 mm × 160 mmPanel Size (approx.) 188 mm × 117 mm × 10 mm
Mass (approx.) 3 kg (including trims and sleeve)
(No.MA341)1-3
KW-AVX900EE
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60 Hz 150 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 15 kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTEROUT/ SUBWOOFER
DVD/CDSignal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=192 kHz 16 Hz to 88 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 95 dBWow and Flutter Less than measurable limit
SDCompatible File System FAT 32/16/12Capacity 8 Mbytes to 2 GbytesData Transfer Rate Maximum 10 Mbps
USBUSB Standards USB 1.1Data Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5V
TVColor System SECAMChannel Coverage VHF: Ch 1 - 12
UHF: Ch 21 - 69MONITOR
Screen Size 7 inch wide liquid crystal displayNumber of Pixel 336 960 pixels: 480 x 3 (horizontal) × 234 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PAL/SECAMAspect Ratio 16:9 (wide)
GENERALPower Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D): With trim plate and sleeve at-tached
Installation Size (approx.) 182 mm × 111 mm × 160 mmPanel Size (approx.) 188 mm × 117 mm × 10 mm
Mass (approx.) 3 kg (including trims and sleeve)
1-4 (No.MA341)
KW-AVX900U
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60 Hz 150 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 15 kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTEROUT/ SUBWOOFER
MONITORScreen Size 7 inch wide liquid crystal displayNumber of Pixel 336 960 pixels: 480 x 3 (horizontal) × 234 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PALAspect Ratio 16:9 (wide)
GENERALPower Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 178 mm × 100 mm × 160 mm
Panel Size (approx.) 171 mm × 97 mm × 21 mmMass (approx.) 2.7 kg (including trims and sleeve)
(No.MA341)1-5
KW-AVX900UN
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60 Hz 150 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 15 kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTEROUT/ SUBWOOFER
MONITORScreen Size 7 inch wide liquid crystal displayNumber of Pixel 336 960 pixels: 480 x 3 (horizontal) × 234 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PALAspect Ratio 16:9 (wide)
GENERALPower Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 178 mm × 100 mm × 160 mm
Panel Size (approx.) 171 mm × 97 mm × 21 mmMass (approx.) 2.7 kg (including trims and sleeve)
1-6 (No.MA341)
KW-AVX900A
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60 Hz 150 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 15 kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTEROUT/ SUBWOOFER
Output Impedance 1 kΩColor System NTSC/PALVideo Output (composite) 1 Vp-p/75 ΩOther Terminals Input LINE IN VIDEO IN CAMERA IN USB input terminal Aerial input
Output 2nd AUDIO OUT, VIDEO OUTOthers CD changer
FM/AM TUNERFrequency Range FM 87.5 MHz to 108.0 MHz
AM 531 kHz to 1 602 kHzFM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)Alternate Channel Selectivity (400 kHz) 65 dBFrequency Response 40 Hz to 15 000 HzStereo Separation 35 dB
AM Tuner Sensitivity/Selectivity 20 µV/35 dBDVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=192 kHz 16 Hz to 88 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 95 dBWow and Flutter Less than measurable limit
SDCompatible File System FAT 32/16/12Capacity 8 Mbytes to 2 GbytesData Transfer Rate Maximum 10 Mbps
USBUSB Standards USB 1.1Data Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5V
MONITORScreen Size 7 inch wide liquid crystal displayNumber of Pixel 336 960 pixels: 480 x 3 (horizontal) × 234 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PALAspect Ratio 16:9 (wide)
GENERALPower Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 178 mm × 100 mm × 160 mm
Panel Size (approx.) 171 mm × 97 mm × 21 mmMass (approx.) 2.7 kg (including trims and sleeve)
(No.MA341)1-7
SECTION 1PRECAUTION
1.1 Safety Precautions
! Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
! Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
1-8 (No.MA341)
1.2 Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.
(2) Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body.
(3) Handling the optical pickup• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easilydestroy the laser diode.
1.3 Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long atime when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4 Attention when traverse unit is decomposed*Please refer to "Disassembly method" in the text for the pickup unit. • Apply solder to the short land before the card wire is disconnected from the connector on the pickup unit.
(If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.)• In the assembly, be sure to remove solder from the short land after connecting the card wire.
1M
(caption)
Anti-static wrist strap
Conductive material
(conductive sheet) or iron plate
Mechanism control board
CN101
Flexible wire
Short-circuit points
(No.MA341)1-9
1.5 Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able to function.
6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure.
REPRODUCTION AND POSITION OF LABELS and PRINT
! Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
WARNING LABEL and PRINT
1-10 (No.MA341)
SECTION 2SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
SECTION 3DISASSEMBLY
3.1 Main body3.1.1 Removing the FRONT PANEL assembly (See Fig.1 to
4)(1) From the bottom side of main body, insert the screwdriver
to hole of the third gear from hole a of the bottom chassis,and then turn the gear to clockwise until FRONT PANELassembly comes up. (See Fig.1)
(2) Remove the two screws A attaching the both side of theFRONT PANEL assembly. (See Fig.2)
(3) Remove the four screws B attaching the both side of theFRONT PANEL assembly. (See Fig.2)
(4) Remove the one screw C attaching the FPC GUIDE. (SeeFig.3)
(5) Remove the one screw D attaching the FRONT CHASSIS.(See Fig.3)
(6) Disconnect the card wire from MONITOR assembly con-nected to connector CN401 of the PANEL BOARD assem-bly. (See Fig.4)
(7) Disengage two hooks a engaged FRONT CHASSIS. (SeeFig.2)
Fig.1
Fig.2
hole a
BB
AA
hook a
hook a
(No.MA341)1-11
Fig.3Fig.4
3.1.2 Removing the HEAT SINK (See Fig.5)(1) Remove the four screws E and three screws F attaching
the HEAT SINK.
Fig.5
C
CN401
D
E
E F
1-12 (No.MA341)
3.1.3 Removing the REAR BRACKET (See Fig.6, 7)(1) Remove the three screws G attaching the REAR HEAT
SINK. (See Fig.6)(2) Remove the thirteen screws H attaching the REAR
BRACKET. (See Fig.6)(3) Disconnect the connector wire from FAN connected to con-
nector CN906 of the SUB BOARD assembly. (See Fig.7)(4) Disconnect the connector wire from USB CABLE connect-
ed to connector CN911 of the SUB BOARD assembly.(See Fig.7)
Fig.6
Fig.7
H H G H
CN906
CN911
(No.MA341)1-13
3.1.4 Removing the TOP CHASSIS assembly (See Fig.8 to 11)(1) Disconnect the card wire from TOP CHASSIS assembly
connected to connector CN702 of the MAIN BOARD as-sembly. (See Fig.8)
(2) Remove the two screws J attaching the FRONT BOARDassembly. (See Fig.8)
(3) Disconnect the connector wire from MAIN BOARD assem-bly connected to connector CN902 of the SUB BOARD as-sembly. (See Fig.9)
(4) Disconnect the card wire from MAIN BOARD assemblyconnected to connector CN904 of the SUB BOARD as-sembly. (See Fig.9)
(5) From left side of MAIN BODY, remove the two screws K at-taching the TOP CHASSIS assembly. (See Fig.10)
(6) From right side of MAIN BODY, remove the two screws Lattaching the TOP CHASSIS assembly. (See Fig.11)
Fig.8
Fig.9
Fig.10
Fig.11
CN702 J
CN904 CN902
KK
L L
1-14 (No.MA341)
3.1.5 Removing the MAIN BOARD assembly (See Fig.12)(1) Disconnect the connector wire from the MECHA SWITCH
BOARD assembly connected to connector CN764 of theMAIN BOARD assembly.
(2) Remove the four screws M attaching the MAIN BOARD as-sembly.
Fig.12
3.1.6 Removing the MID CHASSIS (See Fig.13)(1) Remove the four screws N attaching the MID CHASSIS.
Fig.13
CN764
MM
NN
(No.MA341)1-15
3.1.7 Removing the SUB BOARD assembly (See Fig.14, 15)(1) Disconnect the card wire from CONNECTION BOARD as-
sembly connected to connector CN907 of the SUB BOARDassembly. (See Fig.14)
(2) Disconnect the card wire from SUB BOARD assembly con-nected to connector CN901 of the TV TUNER BOARD as-sembly. (See Fig.15)
(3) Remove the five screws P attaching the SUB BOARD as-sembly. (See Fig.15)
Fig.14
Fig.15
CN907
P
CN901
1-16 (No.MA341)
3.1.8 Removing the TV TUNER BOARD assembly (See Fig.16 to 18)(1) Remove the two screws Q attaching the FRONT PCB
BRACKET. (See Fig.16)(2) Remove the three screws R attaching the SUB PCB
BRACKET. (See Fig.17)(3) Remove the one screw S attaching the TV TUNER BOARD
assembly. (See Fig.18)
Fig.16
Fig.17
Fig.18
Q
R
S
(No.MA341)1-17
3.1.9 Removing the DVD MECHANISM assembly (See Fig.19)(1) Remove the three screws T attaching the DVD MECHA-
NISM assembly.
Fig.19
3.1.10 Removing the CONNECTION BOARD assembly (See Fig.20)(1) Takeout the INSULATOR.(2) Disconnect the card wire from FRONT END BOARD as-
sembly connected to connector CN301 and CN303 of theCONNECTION BOARD assembly.
(3) Remove the four screws U attaching the CONNECTIONBOARD assembly.
Fig.20
T
CN303
CN301
U
U
1-18 (No.MA341)
3.2 Monitor section3.2.1 Removing the FRONT BRACKET assembly (See
Fig.1)(1) Remove the two screws A attaching the FPC COVER.(2) Remove the four screws B attaching the FRONT BRACK-
ET assembly.(3) Remove the two screws C attaching the FRONT BRACK-
ET assembly.
Fig.1
3.2.2 Removing the PANEL BOARD assembly (See Fig.2)(1) Disconnect the connector wire from LCD module connect-
ed to connector CN471 of the PANEL BOARD assembly.(2) Disconnect the card wire from SWITCH BOARD assembly
connected to connector CN431, CN511 and CN591 of thePANEL BOARD assembly.
(3) Remove the four screws D attaching the PANEL BOARDassembly.
(4) Straighten hook a attaching the PANEL BOARD assembly.
Fig.2
3.2.3 Removing the LCD module (See Fig.3)(1) Remove the six screws E attaching the PANEL BRACKET
assembly. (See Fig.3)(2) Disengage seven hooks b engaged PANEL BRACKET.
Fig.3
BB
C
A
D D
CN431 CN511 CN591
CN471hook a
hook b hook b
hook b
E
E E
E
(No.MA341)1-19
3.3 DVD mechanism assembly3.3.1 Removing the mechanism control board
(See Fig.1)Caution:
Before disconnecting the flexible wire extending from the DVDpickup, solder the short-circuit point on the flexible wire usinga grounding soldering iron. If you do not follow this instruction,the DVD pickup may be damaged.(1) Turn over the body, and solder the short-circuit points on
the flexible wire extending from the DVD pickup.(2) Disconnect the flexible wire from connector CN101 on the
mechanism control board.(3) Disconnect the card wire from connector CN201 on the
mechanism control board.(4) Disconnect the flexible wire from connector CN202 on the
mechanism control board.(5) Unsolder two soldered points a on the mechanism control
board and remove the wire extending from the feed motor.(6) Remove the screw A attaching the lug wire.(7) Remove the two screws B and screw C attaching the
mechanism control board.
Caution:• As the flexible wire to be connected to CN101, make sure to
attach it to the mechanism control board using a doubletape.
• After reassembling, unsolder the short-circuit points.
Fig.1
Double tape
Feed motor
Mechanism control board
CN202
CN101
B
a
CB
CN201
Flexible wire
Short-circuit points
A
Lug wire
1-20 (No.MA341)
3.3.2 Removing the top cover (See Fig.2)
(1) Remove the two screws D attaching the top cover on theback of the body.
(2) Remove the top cover upward.
Reference:When reassembling, set part b of the top cover under thebending part c of the chassis frame.
3.3.3 Removing the mechanism section (See Fig.2 to 4)
• Remove the top cover.(1) From the bottom of the body, remove the screw E attaching
the lug wire. (See Fig.2.)(2) Remove the two screws F attaching the right and left stop-
pers on the front side. (See Fig.2.)(3) Remove the two floating springs on the bottom of the body.
(See Fig.3.)(4) Move the mechanism section upward and remove from the
chassis frame.The three damper springs come off from the dampers.(See Fig.4.)
Caution:• When reassembling, reattach the damper spring to the
damper respectively and insert the three shafts on the bot-tom of the mechanism to the dampers.
• Before inserting the shaft to the dampers, apply IPA to thehole of damper.
Fig.2
Fig.3
Fig.4
D
Top cover
Stopper
Stopper
F
F
b
c E
Lug wire
D
Floating spring
Mechanism section
Damper (R)
(Purple)
Damper (F)
(Black)
Damper (F)
(Black)
Chassis frame
Damper SP.(F)
(Silver)
Damper SP.(F)
(Silver)
Damper SP.(R)
(Red)
(No.MA341)1-21
3.3.4 Removing the clamper unit (See Fig.5 to 7)
• Remove the top cover and the mechanism section.(1) Remove the clamper2 spring on the bottom of the mecha-
nism section. (See Figs.5.and 6.)(2) Release the part d of the clamper spring from the bending
part of the chassis base assembly. (See Fig.7.)(3) Move the clamper unit in the direction of the arrow and turn.
Release the two joints e and f, then remove the clamperunit upward. (See Fig.6.)
3.3.5 Reattaching the clamper unit (See Fig.5 to 9)
(1) Attach the clamper spring to the clamper unit. (See Fig.8.)(2) Move the clamper unit to set the side joints e and f to each
boss of the chassis base assembly. Make sure that part gis inserted to the notch of the chassis base assembly. (SeeFigs.5 and 9.)
(3) Move the part d of the clamper spring to the outside of thebending part of the chassis base assembly. (See Fig.7.)
(4) Attach the clamper2 spring to the chassis base assembly.(See Figs.5 and 6.)
Caution:When reattaching, temporarily hook the end of the clamperspring as shown in the figure to make the work easy. (SeeFig.8.)
Fig.5
Fig.6
Fig.7
Clamper unit
Clamper spring
Clamper2 spring
g
f
e
Chassis base assembly
Clamper2 spring
Chassis base assembly
Clamper spring
Chassis base assembly
d
1-22 (No.MA341)
Fig.8
Fig.9
Clamper unit
Clamper spring
Notchg
Clamper unit
(No.MA341)1-23
3.3.6 Removing the front unit (See Fig.10 to 12)
• Remove the top cover and the mechanism section.(1) Disconnect the flexible wire from connector CN202 on the
mechanism control board at the bottom of the body. (SeeFig.10.)
(2) Remove the screw G attaching the front unit on the top ofthe body. (See Fig.11.)
(3) Move the front unit toward the front to release joint h, andrelease two joints i and j on the right side of the chassisbase assembly. Then remove the front unit upward. (SeeFigs.11 and 12.)
(4) Remove the two screws H attaching the switch board. (SeeFig.12.)
Reference:You can remove the switch board only without removing thefront unit.
Caution:When reassembling, attach the flexible wire extending fromthe switch board using the double tape. (See Figs.10 and 12.)
Fig.10
Fig.11
Fig.12
Mechanism control board
Flexible wireCN202
Double tape
GFront unit
h
h
Front unit
Switch board
j
G
H
i
Double tape
1-24 (No.MA341)
3.3.7 Removing the loading arm assembly (See Fig.13 , 14)
• Remove the top cover, the mechanism section and the frontunit.(1) From the top of the body, move the loading arm assembly
from the front side upward, and release the bosses fromthe right and left joints k and m of the chassis base assem-bly.
(2) Release the boss from notch n of the connect arm on theright side of the body, and release the boss from notch p ofthe slide cam assembly on the left side.
Fig.13
Fig.14
k n
m
Loading arm assembly
k
n
m
Loading arm assembly
p
Side camassembly
Connect arm
(No.MA341)1-25
3.3.8 Removing the rod (L)(R)/roller assembly (See Fig.15 and 16)
• Remove the top cover, the mechanism section, the front unitand the loading arm assembly.(1) Release the rod (L) and (R) from the joints q at the bottom
of the loading arm assembly (See Fig.15.)(2) Remove the roller assembly from the loading arm assem-
bly. (See Fig.16.)(3) Remove the two collars and washer from the roller assem-
bly. (See Fig.16.)
Caution:After attaching the loading arm assembly to the roller assem-bly, attach the rod (L) and (R). Attach the rods to the right andleft collars of the roller. (See Fig.15.)When reattaching the rod (L) and (R) to the loading arm as-sembly, engage each joint as shown in Fig.15. As joints q ofthe rod (L), let the rod through q before reattaching it.
Fig.15
Fig.16
q
q
q q
q
q
Rod(R)
Loading arm assembly
Rod(L)
Collar Collar
Rod(R) Rod(L)
Roller assembly
Washer
Collar
Collar
Rod(L)
Loading arm assembly
Rod(R)
1-26 (No.MA341)
3.3.9 Removing the DVD pickup assembly (See Fig.17 to 19)
• Remove the mechanism control board.(1) From the bottom of the body, turn the feed gear in the di-
rection of the arrow to move the DVD pickup outwards.(See Fig.17.)
(2) Remove the screw J attaching the thrust spring. (SeeFig.17.)
(3) Remove the DVD pickup assembly upward on the L.S.gearside and release from sub shaft at joint r. Move the leadscrew of the DVD pickup assembly in the direction of thearrow to release from joint s. (See Fig.18.)
Caution:• When releasing the lead screw at joint s, the L.S.collar
comes off at the end of the lead screw. When reas-sembling, reattach the L.S.collar to the lead screw andengage joint s. (See Fig.18.)
• When reattaching the L.S.collar, reattach it to the points of the lead screw, and to the rod (M). Make sure thatthe L.S.collar is set on the rod (M) spring. (See Fig.18.)
(4) Remove the screw K attaching the rack spring/ rack plateon the DVD pickup. (See Fig.19.)
(5) Pull out the lead screw. (See Fig.19.)
Caution:Perform adjustment after replacing the pickup.
Fig.17
Fig.18
Fig.19
J
Feed gear
Thrust springDVD Pickup assembly
r
sL.S.collar
Rod(M)
L.S.gear
Lead screw
Sub shaft
DVD Pickup assembly
KRack spring
Rack plate
L.S.collar
DVD Pickup
Lead screw
(No.MA341)1-27
3.3.10 Removing the spindle motor (See Fig.20)
• Remove the mechanism control board.Remove the two screws L attaching the spindle motor on thebottom of the body.
Caution:Perform adjustment when reattaching the spindle motor.
Fig.20
3.3.11 Removing the feed motor assembly (See Fig.21 and 22)
• Remove the mechanism control board.(1) Remove the feed TRI. spring on the bottom of the body.
(See Fig.21.)(2) Remove the two screws M attaching the feed motor as-
sembly. (See Fig.21.)(3) Remove the slit washer from the motor H. assembly and
pull out the worm wheel. (See Fig.22.)Remove the two screws N attaching the feed motor. (SeeFig.22.)
Fig.21
Fig.22
L
Spindle motor
M
Feed motor assembly
Feed TRI. spring
Feed motor
Motor H. assembly
Worm wheel
Slit washer
N
1-28 (No.MA341)
SECTION 4ADJUSTMENT
4.1 Test instruments required for adjustment(1) Digital oscilloscope (100MHz)(2) Jitter meter(3) Digital tester(4) Electric voltmeter(5) Tracking offset meter(6) Test Disc : VT501 or VT502(7) Extension studs : STDV001-3P(8) Extension cable :
Caution:Be sure to attach the heat sink and rear bracket onto the poweramplifier IC and regulator IC respectively, before supply thepower. If voltage is applied without attaching these parts, thepower amplifier IC and regulator IC will be destroyed by heat.
4.3 Connection methodConnection procedure
(1) Attach the front chassis assembly to the main board.(2) Attach the heat sink and rear bracket to the main board.(3) Attach the extension studs to the DVD mechanism assembly.(4) Connect the DVD mechanism assembly and the main board with a extension cable.
Power supply voltage DC14.4V(11 to 16V)Load impedance 4Ω (2 Speakers connection)Line Output 20KΩ
iCN381
EXTCN001-6P
a
bCN375
CN376
EXTXC004-20P
EXTFP001-26P
g
CN301
EXTDV002-44PF
EXTDV002-7PF
CN305
EXTJD001-14PF
f
e
h
CN303CN302
EXTJD001-60PF
Bottom view
h
g
CN401
EXTJD001-60PF
CN404EXTJD001-14PF
b
c d
f
i
CN702
EXTDV001-23PF
CN701
CN764CN703
CN705
EXTFP001-26P
EXTCN001-6P
EXTLX001-4P
EXTDV002-44PF
d
a
c
e
EXTXC004-20P
CN903
CN907
CN902
CN904
EXTDV002-7PF
EXTDV001-23PF
EXTLX001-4P
(No.MA341)1-29
4.4 Adjustment method for jitterAfter replacing the pickup, set the unit in the service mode to display a jitter value on the LCD.Confirm that the jitter value measured with a jitter meter is within 12% of the jitter value displayed on the LCD.If it is within 12%, then adjustment is not necessary.If the measured jitter value is outside the 12% tolerance range, perform the following adjustments.
4.4.1 Adjustment procedure(1) Set the unit to the service mode and display a jitter value (hex data) on the LCD.(2) Turn each of the screws a, b and c, by a half-turn per step, in the direction that reduces the jitter value in order to minimize it.(3) (Do not turn a screw more than a half turn at a time, but adjust the screws in the cycle of the same level is turned in the pair of
b+c and the same level is turned in the pair of a+b.)(4) After completing the adjustment, secure the screws with screw lock paint.
b
c
a
3 mm wrench
Jitter value adjustment procedure (Pickup horizontal level adjustment relative to the DVD recording surface)
(For the adjustment tool use a 3 mm wrench and not a screwdriver, this procedure will make the adjustment easier.)
1-30 (No.MA341)
4.5 Jitter value conversion tableLoad the test DVD and set the unit to the service mode. A jitter value converted to the hex value is displayed on the LCD.Refer to the corresponding decimal notation value shown in the following Jitter Conversion Table.The adjustment is OK if the jitter value measured with a jitter meter is within 12% of the jitter value displayed on the LCD.If the measured jitter value is outside the 12% tolerance range, adjust it to minimize the difference between the measured value andthe displayed value.
Indicated
on the LCD
Jitter value
(%)
Jitter value
(%)Indicated
on the LCD
Jitter value
(%)Indicated
on the LCD
EF56
EF22
EEEE
EEBA
EE86
EE52
EE1E
EDEA
EDB6
ED82
ED4E
ED1A
ECE6
ECB2
EC7E
EC4A
EC16
EBE2
EBAE
EB7A
EB46
EB12
EADE
EAAA
EA76
EA42
EA0E
E9DA
E9A6
E972
E93E
E90A
E8D6
E8A2
E86E
E83A
E806
E7D2
4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7.0
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8.0
8.1
8.2
8.3
8.4
E79E
E76A
E736
E702
E6CE
E69A
E666
E632
E5FE
E5CA
E596
E562
E52E
E4FA
E4C6
E492
E45E
E42A
E3F6
E3C2
E38E
E35A
E326
E2F2
E2BE
E28A
E256
E222
E1EE
E1BA
E186
E152
E11E
E0EA
E0B6
E082
E04E
E01A
8.5
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
10.0
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11.0
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
12.0
12.1
12.2
DFE6
DFB2
DF7E
DF4A
DF16
DEE2
DEAE
DE7A
DE46
DE12
DDDE
DDAA
DD76
DD42
DD0E
DCDA
DCA6
DC72
DC3E
DC0A
DBD6
DBA2
DB6E
DB3A
DB06
DAD2
DA9E
DA6A
DA36
DA02
D9CE
D99A
D966
D932
D8FE
D8CA
D896
D862
12.3
12.4
12.5
12.6
12.7
12.8
12.9
13.0
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
14.0
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
15.0
15.1
15.2
15.3
15.4
15.5
15.6
15.7
15.8
15.9
16.0
Calculation
Indicated on the LCD Jitter (%)
E9A6 7.5
(No.MA341)1-31
4.6 Service mode
4.6.1 Service mode 1 (Indication of a service mode 1 is nothing.)
4.6.2 Service mode 2
Up Button
REW Button
[ STANDBY/ON ATTENUATOR ]
[ AV MENU or TP/PTY ]
[ VOLUME - ]
[ VOLUME + ]
[ OPEN ]
FF ButtonTOUCH PANEL
DOWN Button
Exchanging it operate a menu of a service mode with the [UP] button and [DOWN]
button. Operate choice of a menu with a [ENT] button.
*1 : When an [ENT] button is pushed in NO EJECT indication, it is set by an EJECT
prohibition mode.
When an [ENT] button is pushed in EJECT OK indication, it is set by a normal
mode.
*2 : Forced EJECT movement
A screen becomes normal indication after an ENT button was pushed.
Keep this state more 2 seconds
while continuing pressing the
[STANDBY/ON ATTENUATOR] button
and [OPEN] button sequentially.
Screen indication
NO EJECT?
EMERGENCY EJECT?
*1
*2
Keep this state more 2 seconds
while continuing pressing the
[AV MENU or TP/PTY] button, [OPEN]
button and TOUCH PANEL [UP]
button sequentially.
Screen indication
SERVICE MODE 2
INITIALIZE ALL
INITIALIZE
INITIALIZE DVD
INITIALIZE BT
TOUCH PANEL CALIBRATION
Exchanging it operate a menu of a service mode with the [UP] button
and [DOWN] button. Operate choice of a menu with a [ENT] button.
1-32 (No.MA341)
INITIALIZE DVD
INITIALIZE BT
Full initialization of EEPROM of a DVD unit
( It is included a permanent domain)
After clear completion, this indication is continued till an effective key is input.
Full initialization of EEPROM of Bluetooth ( Module/Hideaway )
After clear completion, this indication is continued till an effective key is input.
INITIALIZE DVD
OK **
INITIALIZE BT
OK **
TOUCH PANEL CALIBRATION
Push the center of a + character displayed in turn.
INITIALIZE
NOW
INITIALIZE INITIALIZE
OK **
INITIALIZE (Initialization of a user area of each
EEPROM)
Main micon EEPROM initialization (a user entry
domain )
(a user entry domain, speaker setting, subarea
of J-version, data to pre-set )
Panel micon EEPROM initialization (picture
adjustment data )
DVD unit EEPROM initialization (except
a permanent domain)
After clear completion, a screen returns to
normal indication after OK indication was
displayed for three seconds.
INITIALIZE ALL
NOW
INITIALIZE ALL INITIALIZE ALL
OK **
INITIALIZE ALL (Each EEPROM is initialized by
a factory shipment state.)
Main micon EEPROM initialization (user entry
domain, error history, speaker setting, subarea
of J-version, data to pre-set )
Panel micon EEPROM initialization (picture
adjustment data)
DVD unit EEPROM initialization (except
a permanent domain)
Bluetooth (Module/Hideaway) EEPROM
initialization
After clear completion, a screen returns to
normal indication after OK indication was
displayed for three seconds.
+
+
+ +
+
(No.MA341)1-33
4.6.3 Service mode 3
DVD NTSC/PAL
NTSC
PAL
DVD picture change
JD9 output picture setting (NTSC)
JD9 output picture setting (PAL)
TEMPERATURE Temperature data reading
Temperature data by the temperature sensor in the main micon
and JD9-PCB is read every 5 seconds and displayed in hex numbers.
MEMORY CHECK (It is displayed only at the time of the disc insertion)
Memory residual quantity indication mode
Data residual quantity of a disc is displayed by LCD.
About the playback control-related key ([FSKIP], [BSKIP], [UP],
[DOWN], [VOL]), only movement is effective.
Indication does not change as memory residual quantity indication.
About cancellation of this mode, press the
[STANDBY/ON ATTENUATOR] button.
SERVICE MODE
SERVICE MODE
VERSION
AREA/REGION
TEMPERATURE
MEMORY CHECK
DVD NTSC/PAL
DVD CHECK MODE
SERVICE MODE
ERROR READ
ERROR CLEAR
BT VERSION
Exchanging it operate
a menu of a service mode
with the [UP] button and
[DOWN] button.
Operate choice of a menu
with a [ENT] button.
Return to previous menu
with a [BACK] button.
VERSION
MAIN
JD9
CH
PANEL
P.ADJ
V**** [**]
****
******
V**** V*** [**]
**
Micon version indication
Main micon version and ROM correction
version
JD9 version
CH version
Panel micon version and ROM correction
version
00 : Panel No adjustment (factory use)
01 : Complete Panel adjustment
(factory use)
AREA/REGION
SYS-AREA : *
JD9-AREA : **
JD9-REGION : *
JD9-CPPM : Y ****
Area and region indication
Main micon area
JD9 area
JD9 region
CPPM Y : Finished with a note
N : Non-note
**** : Check sum
Keep this state more 2 seconds
while continuing pressing the
[AV MENU/TP PTY] button, [VOLUME -]
button and TOUCH PANEL [DOWN]
button sequentially.
Screen indication
SERVICE MODE 3SERVICE MODE
INITIALIZE ALL
RUNNING MODE
Exchanging it operate a menu of a service mode with the [UP] button
and [DOWN] button. Operate choice of a menu with a [ENT] button.
1-34 (No.MA341)
INITIALIZE ALL
NOW
INITIALIZE ALL INITIALIZE ALL
OK **
INITIALIZE ALL (Each EEPROM is initialized
by a factory shipment state.)
Main micon EEPROM initialization (user entry
domain, error history, speaker setting, subarea
of J-version, data to pre-set )
Panel micon EEPROM initialization (picture
adjustment data)
DVD unit EEPROM initialization (except
a permanent domain)
Bluetooth module EEPROM initialization
After clear completion, a screen returns to
normal indication after OK indication was
displayed for three seconds.
RUNNING MODE
See "Running mode" for details.
ERROR READ
DVD ERROR READ
CH ERROR READ
MECHA ERROR READ
READ ALL
ERROR CLEAR
DVD ERROR CLEAR
CH ERROR CLEAR
MECHA ERROR CLEAR
DVD CHECK MODE
See "DVD CHECK MODE" for details.
DVD ERROR READ
Reading of a DVD unit error history
CH ERROR READ
Reading of a CD changer error history
MECHA ERROR READ
Reading of a door mechanism error history
READ ALL
Reading of a main micon EEPROM (All contents)
BT VERSION
SW BT CORE ***
HW BT MODULE ***
SW BT MODULE ***
SW HIDEAWAY ***
ADR-************
Bluetooth version indication
Software version of BT core
Hardware version of BT Module
Software version of BT Module
Software version of BT Hideaway
controller
BT Address
Clear of each error history
A screen returns to following indication
after clear completion.
(No.MA341)1-35
4.6.4 Service mode 4
4.7 DVD check mode
Keep this state more 2 seconds
while continuing pressing the
[AV MENU/TP PTY] button, [VOLUME +] button
and TOUCH PANEL [DOWN] button sequentially.
Screen indication
SERVICE MODE 4RDS S MODE
MONITOR S MODE
Exchanging it operate a menu of a service mode with the [UP] button and [DOWN] button.
Operate choice of a menu with a [ENT] button.
MONITOR S MODE
R/W CHROMA 1
R/W CHROMA 2
DATA CLEAR
RDS S MODE
RDS service mode (Only RDS model)
*See "Monitor adjustment" for details.
CHROMA DATA read/write of NTSC/PAL signal processing IC
CHROMA DATA read/write of TFT driver IC
Clear of CHROMA DATA of 1,2 (return to an initial value)
DVD CHECK MODE
NORMAL PLAY
EF OUT-TRACKING OFF
EF IN-TRACKING OFF
CD-LASER ON
DVD-LASER ON
DVDx1 JITTER MODE
DVD CHECK MODE
EEPROM DATA DISP
EEPROM DATA CLEAR
TEMPERATURE
SEARCH & JITTER
MONITOR
PLAY
DVD CHECK MODE
STOP
OPEN
Exchanging it operate a menu of a service mode with the [UP] button and [DOWN] button.
Operate choice of a menu with a [ENT] button.
Command Mechanism unit operation Indication contents
NORMAL PLAY
EF OUT-TRACKING OFF
EF IN-TRACKING OFF
CD-LASER ON
DVD-LASER ON
DVDx1 JITTER MODE
EEPROM DATA DISP
EEPROM DATA CLEAR
TEMPERATURE
SEARCH & JITTER
MONITOR
PLAY
STOP
OPEN
Start at normal speed
(After start, jitter is measured by an inner position.)
Tracking off the outermost position of CD
Tracking off the innermost position of CD
CD_LD lights and laser current is displayed.
DVD_LD lights and laser current is displayed
DVD x1 jitter measuring mode
(for use in mechanism adjustment)
Contents of EEPROM is displayed.
Contents of EEPROM is initialized.
Temperature indication
The search and jitter measurement to an appointed
position of DVD.
Monitor terminal setting
DVD x1 stopped start
(After start, jitter is measured by an inner position.)
1. Time out error by ANGLE 1 position cannot detect.
Angle positioning error
Moving to 10 degrees (ANGLE 2 error)
1. Time out error by ANGLE 2 position cannot detect at moving to open position.
2. Missing to ANGLE 1 and detected ANGLE 2 position at moving to open position.
3. Time out error by ANGLE 2 cannot detect at moving close position.
Moving to 20 degrees (ANGLE 3 error)
1. Time out error by ANGLE 3 position cannot detect at moving to open position.
2. Missing to ANGLE 2 and detected ANGLE 3 position at moving to open position.
3. Time out error by ANGLE 3 cannot detect at moving close position.
Moving to 30 degrees (ANGLE 4 error)
1. Time out error by ANGLE 4 position cannot detect at moving to open position.
2. Missing to ANGLE 3 and detected ANGLE 4 position at moving to open position.
3. Time out error by ANGLE 4 cannot detect at moving close position.
Abnormal switch position at moving panel
The Panel move to open and close position, detected abnormal switch position.
0D0021
0D0022
0D0023
0E0031
0E0032
0E0033
0F0041
0F0042
0F0043
0A0000
0A0001
0B0006
1-38 (No.MA341)
4.9 Running mode
Indication Explanation Operation contents of 1 cycle In mecha error In disc error
RUNNING1 MECHA
RUNNING2 MECHA
RUNNING3 DVD
RUNNING4 DVD
RUNNING5 DVD
RUNNING6 DVD
RUNNING7 DVD
RUNNING8 DVD
Door mecha running 1
Door mecha running 2
DVD+Door mecha running1
DVD+Door mecha running2
DVD+Door mecha running3
DVD+Door mecha running4
DVD+Door mecha running5
DVD+Door mecha running6
Panel close Panel open
Panel close Panel open
Panel detach position
Panel angle RETRY
3 position
Panel angle 1 position
Panel angle 2 position NO RETRY
Loading Eject
Wait for 5 seconds+Door open/close
Loading Eject
Wait for 5 seconds+Door open/close
Loading Playback Eject
Wait for 5 seconds+Door open/close
Loading Playback Eject
Wait for 5 seconds+Door open/close
Loading Playback Eject
Wait for 5 seconds+Door open/close
Loading Playback Eject
Wait for 5 seconds+Door open/close
-
Retry
Stop
Stop
Retry
Stop
Retry
Stop
Retry
-
-
-
-
-
Stop
Stop
Retry
Retry
* Cancellation of running1,2 : Press the [EJECT] key
* In running 1,2 cancellation, a door does not stop at the position and moves to a panel position.
* Cancellation of running3 to 8 : Press the [POWER] key
* The number of count and an error cord are displayed in running.
Playback contents in a running mode
CD
The first track is played for 30 seconds. The last track is played for 30 seconds.
(The last track is played in the case of less than till the last for 30 seconds.)
DVD
2layer disc (Pit disc)
Title 1 (the L0 layer internal circumference) is played for 30 seconds.
Title 12 (L0 layer circumference) is played for 30 seconds.
Title 24 (L1layer internal circumference) is played for 30 seconds.
2layer disc (Recordable disc)
Title 1 (the L0 layer internal circumference) is played for 30 seconds.
Title 13 (L0 layer circumference) is played for 30 seconds.
Title 24 (L1layer internal circumference) is played for 30 seconds.
1layer disc
First chapter of title 1 is played for 30 seconds. The last chapter of title 1 is played for 30 seconds.
(No.MA341)1-39
4.10 Monitor adjustment
Indication
* When adjusting, switch on the main unit and insert a test disc (VT-501). And play the test disc and pause it.
1. Set the service mode 4.
2. Exchanging it operate a menu of a service mode with the [UP] button and [DOWN] button.
3. Change data with the [B.SKIP]/[F.SKIP] buttons.
4. Write data with a [ENT] button.
R/W CHROMA 1
Detail
Contrast
Color (NTSC)
Color (PAL)
Color (SECAM)
Tint (NTSC)
Tint (PAL)
Tint (SECAM)
Sharpness
Brightness
ABL off
Sub Contrast
White Lim
Black Lim
Gamma 1
Gamma 2
Sub Brt R
Sub Brt B
Drive R (NTSC)
Drive R (PAL)
Drive R (SECAM)
RY Gain
RY Phase (NTSC)
RY Phase (PAL)
RY Phase (SECAM)
Drive G (NTSC)
Drive G (PAL)
Drive G (SECAM)
GY Gain
GY Phase (NTSC)
GY Phase (PAL)
GY Phase (SECAM)
Drive B (NTSC)
Drive B (PAL)
Drive B (SECAM)
Com Amp
Com DC
AFC2 Phase
DRVSEL
Unknown 1
Unknown 2
LPF
Unknown 3
Contrast control
Color control
Color control
Color control
Tint control
Tint control
Tint control
Sharpness control
Brightness control
Auto brightness limiter off
Controls the Y amplitude
White clipping voltage for RGB signal
exceeding over white
White clipping voltage for RGB signal
exceeding over white
Correction peak point
Boost gain correction peak point
Sub brightness control for R output signal
Sub brightness control for R output signal
Gain control for RGB video signal
Gain control for RGB video signal
Gain control for RGB video signal
Relative amplitude of R-Y color
difference signal
Relative phase of G-Y color
difference signal
Relative phase of G-Y color
difference signal
Relative phase of G-Y color
difference signal
Gain control for RGB video signal
Gain control for RGB video signal
Gain control for RGB video signal
Relative amplitude of R-Y color
difference signal
Relative phase of G-Y color
difference signal
Relative phase of G-Y color
difference signal
Relative phase of G-Y color
difference signal
Gain control for RGB video signal
Gain control for RGB video signal
Gain control for RGB video signal
Common pulse amplitude
Reference DC output
AFC2 phase control
Driving ability of pulse output stage
LPF
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
3F
3F
3F
3F
3F
3F
3F
20
40
01
05
F0
0F
80
80
50
05
2F
2F
2F
00
00
00
00
2F
2F
2F
00
00
00
00
2F
2F
2F
80
80
10
00
00
00
10
00
7F
7F
7F
7F
7F
7F
7F
3F
FF
01
0F
0F
0F
FF
FF
0F
0F
3F
3F
3F
01
01
01
01
3F
3F
3F
01
01
01
01
3F
3F
3F
FF
FF
07
03
01
01
01
01
47
3A
3D
3B
3D
42
41
24
C9
01
06
F0
0F
3E
42
05
04
1E
1E
21
01
00
00
00
19
19
19
1D
00
00
00
00
1C
1C
25
8D
84
00
00
00
00
00
00
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Fix
Adjust
Fix
Adjust
Fix
Fix
Fix
Fix
Adjust
Adjust
Adjust
Adjust
Adjust
Fix
Fix
Fix
Fix
Adjust
Adjust
Adjust
Fix
Fix
Fix
Fix
Adjust
Adjust
Adjust
Adjust
Adjust
Fix
Fix
Fix
Fix
Fix
Fix
Minimum
value
Maximum
value
Initial
value
Reference
register value
1-40 (No.MA341)
Indication Minimum
value
Maximum
value
Initial
value
Reference
register value
Detail
DOTCLK Freq. Range
EXCHFI
PLL offset (NTSC)
PLL offset (PAL)
PLL offset (SECAM)
VD Phase (NTSC)
HD Phase (NTSC)
S GP Phase
S-ID Sense
S-ID M
HP Boost
P/N ID S
BPF/HPF
SECAM R-Y Black Adj
SECAM B-Y Black Adj
Gamma2-R
Gamma2-G
Gamma2-B
VD Phase (PAL)
VD Phase (SECAM)
HD Phase (PAL)
HD Phase (SECAM)
DOTCLK adjustment
VD phase phase
DOTCLK adjustment
DOTCLK adjustment
DOTCLK adjustment
VD out phase
HD out phase
SECAM gate pulse phase
SECAM ID sensitivity
SECAM ID mode
Enhance the higher side of SECAM
bell filter
PAL / NTSC ID sensitivity for digital
comb filter
Select chroma BPF frequency response
R-Y black level adjust for SECAM
R-Y black level adjust for SECAM
VD out phase
VD out phase
HD out phase
HD out phase
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
2F
2F
2F
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
07
03
3F
3F
3F
07
1F
03
01
01
01
01
01
0F
0F
03
03
03
07
07
1F
1F
07
00
1E
2B
2B
04
04
00
00
00
00
00
00
09
08
00
00
00
03
03
05
05
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Indication Minimum
value
Maximum
value
Initial
value
Reference
register value
R/W CHROMA 2
Detail
USER-BRIGHT
SUB-BRIGHT R
SUB-BRIGHT B
CONTRAST
SUB-CONTRAST R
SUB-CONTRAST B
GAMMA 1
GAMMA 2
COM-LEVEL
COM-DC (NTSC)
VCO 11 (NTSC)
VCO 11 (PAL)
LPF
TRAP
SLCLP1
SLCLP0
H-POSITION (NTSC)
S/H-POSITION
HDO-POSITION
SLPAIR
BLK-POSITION
S/H-POSITION2
H POSITION (NTSC)
H-POSITION (PAL)
VCO 33 (NTSC)
VCO 33 (PAL)
COM-DC (PAL)
H POSITION (PAL)
Brightness control
Sub brightness control for R output signal
Sub brightness control for R output signal
Contrast control
Controls the Y amplitude
Controls the Y amplitude
Correction peak point
Boost gain correction peak point
COM-LEVEL
Reference DC output
VCO FREE-RUN adjustment (NTSC)
VCO FREE-RUN adjustment (PAL)
LPF
TRAP
SLCLP1
SLCLP0
H-POSITION
S / H POSITION
HDO-POSITION
SLPAIR
BLK-POSITION
S / H POSITION2
H-POSITION
VCO FREE-RUN adjustment (NTSC)
VCO FREE-RUN adjustment (PAL)
Reference DC output
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
FF
3F
3F
80
3F
3F
3F
3F
3F
3F
80
80
00
00
00
00
3F
00
00
00
00
00
00
3F
80
80
3F
00
FF
7F
7F
FF
7F
7F
7F
7F
7F
7F
FF
FF
07
01
01
01
3F
07
1F
01
1F
07
0F
3F
FF
FF
7F
0F
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
Fix
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
01
01
00
00
00
00
(No.MA341)1-41
4.11 TV tuner adjustment4.11.1 Test instruments1. DC power supply2. Multitest signal generator3. Attenuator4. Wave form monitor5. TV monitor
6. Frequency counter7. Oscilloscope (Using audio out confirmation and adjustment)8. AC millivolt meter9. Distortion meter10. Digital multimeter (Voltage adjustment use)
4.11.2 Test wiring diagram
4.11.3 Test points
DC power
supply
KW-AVX900
(MAIN UNIT)
TV tuner board
RF MULTITEST SIGNAL
GENERATOR
ATTENUATOR
ANT
Tesst points for TV tuner board
IN
OUT
IN
OUT
AC MILLIVOLT
METER
DISTORTION
METERWAVE FORM
MONITOR
TV MONITOR
OSCILLOSCOPE
FOR AUDIO SIGNAL
CHECK
75 ohm
C980
R926
C944
C943
C930
R929
X901
R970
C939C938
R937
C935
C934
R936
C937
L907R
934R
933
C933
R931
R932
R921
C921
R927
C931
C920D905
R919
R925
R920
R924
R918
R922
R923
C919
C918
D904
D903
D902
D901
C923
C922
C924
C925
C927
C928
R935 C936
L904
C929
L903
L906
C926
D906
L902 R928C932
C942
C941
C978
Q902
TP907
C950
TP908
TU901
C965
C964
C963
TP905TP906
TP919
Q901
TP920
1-42 (No.MA341)
4.11.4 SSG Memory
For KW-AVX900 A, EU, U, UN version
Memory
No. 30
Memory
No. 31
Memory
No. 33
Memory
No. 34
Video Color
Signal select
Multiplex pattern
Mode select
Sound MPX
Teletext
Crrier
Country
Mode select
RF TV system
VIDEO output
fs 1 INT OSC
CH1
Frequency (MHz)/PDC VPS
CH2
PAL
MULTI BURST
OFF
ALL ON
OFF
- - - -
- - - -
- - - -
- - - -
ALL OFF
203.25MHz
B G H
MAX
INT 400Hz
STD
ON STD INT
ON STD
PAL
COLOR BAR-2
OFF
ALL ON
OFF
- - - -
- - - -
- - - -
- - - -
ALL OFF
203.25MHz
B G H
MAX
INT 400Hz
STD
ON STD INT
ON STD
PAL
COLOR BAR-2
OFF
ALL ON
ON
- - - -
- - - -
- - - -
- - - -
ALL OFF
471.25MHz
B G H
MAX
- - - -
STD
ON STD INT
ON STD
PAL
COLOR BAR-2
OFF
ALL ON
OFF
- - - -
- - - -
- - - -
- - - -
ALL OFF
471.25MHz
B G H
MAX
INT 400Hz
STD
ON STD INT
ON STD
Carrier output Vision
Sound
Level*1
For KW-AVX900 EE version
Memory
No. 30
Memory
No. 31
Memory
No. 33
Memory
No. 34
Video Color
Signal select
Multiplex pattern
Mode select
Sound MPX
Teletext
Crrier
Country
Mode select
RF TV system
VIDEO output
fs 1 INT OSC
CH1
Frequency (MHz)/PDC VPS
CH2
SECAM
MULTI BURST
OFF
ALL ON
OFF
- - - -
- - - -
- - - -
- - - -
ALL OFF
199.25MHz
D K K1
MAX
INT 400Hz
STD
ON STD INT
ON STD
SECAM
COLOR BAR-1
OFF
ALL ON
OFF
- - - -
- - - -
- - - -
- - - -
ALL OFF
199.25MHz
D K K1
MAX
INT 400Hz
STD
ON STD INT
ON STD
SECAM
COLOR BAR-1
OFF
ALL ON
ON
- - - -
- - - -
- - - -
- - - -
ALL OFF
471.25MHz
D K K1
MAX
- - - -
STD
ON STD INT
ON STD
SECAM
COLOR BAR-1
OFF
ALL ON
OFF
- - - -
- - - -
- - - -
- - - -
ALL OFF
471.25MHz
D K K1
MAX
INT 400Hz
STD
ON STD INT
ON STD
Carrier output Vision
Sound
Level*1
(No.MA341)1-43
4.11.5 Adjustment and check method(1) Turn ON the main power switch.(2) Make it a TV tuner mode.(3) Make frequency same as SSG memory.
Step
No.
1 31 51 VR901- - -
2
3
4
5
6
7
8
9
10
11
12
ItemSSG memory
except EE EE
ATT
posision
Measuring instrument
& check point
Adjustment
point
Adjustment value
& check valueOther
DIVER frequency
adjustment
Frequency counter
TP906
RF AGC adjustment
(Preadjustment)
V-DETECT adjustment
(Preadjustment)
RF AGC adjustment
V-DETECT adjustment
S-DETECT adjustment
SD sensitivity adjustment
SD detect level check
Video frequenct
response check
Video level check
Audio output level check
Distortion check
15.625kHz 25Hz
31 51 VR9020dB Wave form monitor
CN901 12(VIDEO OUT)Most sharp wave
& sat at the sync
point
Adjustment of wave
form See Fig.1
30 50 L90920dB Wave form monitor
CN901 12(VIDEO OUT)
Most sharp wave
point
Adjustment of wave
form See Fig.2
31 51 VR9020dB Wave form monitor
CN901 12(VIDEO OUT)
Most sharp wave
point
Adjustment of wave
form See Fig.1
30 50 L90920dB Wave form monitor
CN901 12(VIDEO OUT)
Most sharp wave
point
Adjustment of wave
form See Fig.2
33 53 L91020dB Digital multimeter
TP9203.20 0.05V
34 54 VR90470dB Oscilloscope
CN901 7(SD OUT)
Level change
point H (5.0V)
34 54 - - - -90dB Oscilloscope
CN901 7(SD OUT)
L (0.0V)
CAUTION:VR904 rotate
clockwise.
Adjust at VR dead point
if rotate CCW.
30 50 - - - -20dB Wave form monitor
CN901 12(VIDEO OUT)
Check wave form See Fig.3
31 51 - - - -20dB Wave form monitor
CN901 12(VIDEO OUT)
video: More than
90 IRE
Sync: More than
30 IRE
31 51 - - - -20dB Oscilloscope
CN901 8(AUDIO OUT)
235~380mV
(60% MOD.)
31 51 - - - -20dB Oscilloscope
CN901 8(AUDIO OUT)
Less than 2.5%
See Fig.4
Fig.1
ADJUST TO MOST SHARP
WAVE POINT.
ADJUST TO SAG
MINIMUM POINT.
Fig.2
ADJUST TO MOST SHARP
WAVE POINT.
ADJUST TO SAG
MINIMUM POINT.
4MHz: MORE THAN 50 [IRE]Fig.3 Fig.4
MORE THAN
90 [IRE]
MORE THAN
30 [IRE]
1-44 (No.MA341)
Fig.1
ADJUST TO MOST SHARP
WAVE POINT.
ADJUST TO SAG
MINIMUM POINT.
Fig.1
ADJUST TO MOST SHARP
WAVE POINT.
ADJUST TO SAG
MINIMUM POINT.
Fig.2
ADJUST TO MOST SHARP
WAVE POINT.
ADJUST TO SAG
MINIMUM POINT.
Fig.2
ADJUST TO MOST SHARP
WAVE POINT.
ADJUST TO SAG
MINIMUM POINT.
4MHz: MORE THAN 50 [IRE]Fig.3
4MHz: MORE THAN 50 [IRE]Fig.3
Fig.4
MORE THAN
90 [IRE]
MORE THAN
30 [IRE]
Fig.4
MORE THAN
90 [IRE]
MORE THAN
30 [IRE]
Wave form for KW-AVX900 EU, U, UN A version
Wave form for KW-AVX900 EE version
(No.MA341)1-45
SECTION 5TROUBLESHOOTING
5.1 16 PIN CORD DIAGRAM (for EU, EE version)
L.GN
BK
YL
GN
GN/BK
VI
VI/BK
WH/BK
GY
GY/BK
RD
YL
WH
BK
RD
BL
WH
BR
Black
Red
Blue
White
Brown
GN
VI Violet
GY Gray
YL Yellow
Green
OR/WH
BR
BL/WH
16
9
10
14
12
15
7
16
8
13
15
6
2
11
3
12
4
10
9
1
5
OR Orange
14
NC
L.GN
7
8
6
2
3
4
1
5
NC
NC
BL/WH
RD
BR
WH/BK
BK
YL
VI
GY
WH
GN
VI/BK
WH/BK
GN/BK
GY/BK
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
L.GN
GN
GN/BK
VI/BK
BL/WH
OR/WH
GY/BK
WH/BK
WH
VI
NC
GY
BR
RD
BK YL
L.GN LightGreen
1-46 (No.MA341)
5.2 16 PIN CORD DIAGRAM (for U, UN, A version)
GN
WH
GN/BK
WH/BK
VI/BK
GY/BK
VI
GY
BL
BR
BL/WH
RD
OR/WH
BK
YL
L.GN
1
3
2
4
5
6
7
8
9
1 0
11
12
1 3
1 4
1 5
16
BK
RD
BL
WH
BR
Black
Red
Blue
White
Brown
GN
VI Violet
GY Gray
YL Yellow
Green
L.GN LightGreen
OR Orange
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
L.GN
GN
GN/BK
VI/BK
BL/WH
OR/WH
GY/BK
WH/BK
WH
VI
BL
GY
BR
RD
BK YL
(No.MA341)1-47
(No.MA341)
VPTPrinted in Japan
Victor company of Japan, LimitedMobile Entertainment Business Group Mobile Entertainment Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
Contents
Block diagram
Standard schematic diagrams
Printed circuit boards
2-1
2-2
2-9 to 12
CD-ROM No.SML200706
SCHEMATIC DIAGRAMSDVD RECEIVER WITH MONITOR
No.MA341SCH
2007/6
KW-AVX900EU,KW-AVX900EE,KW-AVX900U
KW-AVX900UN,KW-AVX900A
COPYRIGHT 2007 Victor Company of Japan, Limited.
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
(for EU,EE)
! Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Safety precaution
! Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
2-1
USBD+/-
VOUTSW1MONSW1MONSW3
VOUTSW1VOUTSW2
PONPOWER ON
KEY1, KEY2
-9V
L/R HDSDAGC
Block diagram
BATT
Q823,Q824
PS2
VDD5V, SW5V, ACC5V,A9V, M8V,D8.5V
IC601
IC602
GDC
D0 to 15, WE0, REA0 to 20, WE1, VSELGDC_CS, GDC_CLKGDC_INT, GDC_RDYGDCRST
GDC-RGDC-GGDC-BGDC-CSYNC
TP-O-X, TP-O-Y, TP-I-X, TP-I-Y, TP-SEN
SW_FREQ
Q8041 to Q8043
-12/LED13V REG.
MEMORY
MEMORY
IC603,Q601 to Q603
GDC 2.5V REG.2.5V PANEL3.3V
DVDSW
Q825
Q827
SW5V
A5V
IC824
Q702,Q703
D3.3V REG.
IC802,IC804
SW REG. CONTROLLER
SW3.3VSUB_D3.3V
VDD5VD3.3V
IC871,IC872
SW3.3V REG.
D5V,M5V,S5V
PANEL3.3V
IC823
PANEL3.3V REG.
IC822,Q821,Q822
SW5V REG.M8V
DVDM8V
Q801,Q802
DVDM8V REG.
PANEL-12VLED13V Q8091
-9V REG.
PANEL18.5V
Q8061
PANEL18V
REG.
CN
101
D1.2V
D2V
IC201
DRIVER
MA0 to 11, MDQ0 to 15DQM0, DQM1, BA0, BA1MCK, NWE, NCSMNCAS, NRASIC399
D1 MC2838-X DIODED2 MA111-X SI DIODED3 MA111-X SI DIODED51 MA22D23-X SB DIODED151 MC2836-X DIODED251 MC2836-X DIODED352 MA111-X SI DIODED361 MA111-X SI DIODED362 MA8047/M/-X Z DIODE EU,EED371 MA8110/M/-X Z DIODED702 MA2SD31-X SB DIODED731 MA111-X SI DIODED821 RB051L-40-X SB DIODED822 RB051L-40-X SB DIODED823 MA22D23-X SB DIODED824 MA22D23-X SB DIODED841 MA8110/M/-X Z DIODED842 MC2836-X DIODED843 MA111-X SI DIODED845 MA111-X SI DIODED846 MC2836-X DIODED847 MA111-X SI DIODED850 1N5401-F64 SI DIODED861 MA22D23-X SB DIODED871 CRS03-W SB DIODED872 CRS03-W SB DIODED3803 MA22D23-X SB DIODED3804 MA8056/M/-X Z DIODED8041 RB051L-40-X SB DIODED8061 CRS03-W SB DIODED8062 CRS03-W SB DIODED8063 MA111-X SI DIODED8064 MA111-X SI DIODED8065 MA8180/H/-X Z DIODED8066 MA111-X SI DIODED8091 MA8091/M/-X Z DIODED8092 MA111-X SI DIODED8601 RB051L-40-X SB DIODED8602 RB051L-40-X SB DIODED8603 RB051L-40-X SB DIODED8801 MA22D23-X SB DIODED8802 MA22D23-X SB DIODE U,UN,AD8803 MA22D23-X SB DIODE U,UN,AD8804 MA22D23-X SB DIODE
C1 NCB31AK-474X C CAPACITOR 0.47uF 10V K EU,EEC2 NCB31HK-102X C CAPACITOR 1000pF 50V K EU,EEC3 NCB31HK-472X C CAPACITOR 4700pF 50V K EU,EEC4 NCB31HK-103X C CAPACITOR 0.01uF 50V K EU,EEC5 NCB31HK-103X C CAPACITOR 0.01uF 50V K U,UN,AC7 NCF31HZ-473X C CAPACITOR 0.047uF 50V ZC8 QETN1EM-107Z E CAPACITOR 100uF 25V MC9 NCB31CK-104X C CAPACITOR 0.1uF 16V KC10 NDC31HJ-101X C CAPACITOR 100pF 50V JC11 NCB31HK-104X C CAPACITOR 0.1uF 50V K EU,EEC12 QETN1CM-107Z E CAPACITOR 100uF 16V MC14 QETN1AM-227Z E CAPACITOR 220uF 10V MC15 NCB31HK-103X C CAPACITOR 0.01uF 50V KC17 QETN1EM-476Z E CAPACITOR 47uF 25V MC18 NCB31CK-473X C CAPACITOR 0.047uF 16V KC19 QETN1EM-476Z E CAPACITOR 47uF 25V MC20 NCB31HK-103X C CAPACITOR 0.01uF 50V KC31 NCB31HK-103X C CAPACITOR 0.01uF 50V K EU,EEC32 QERF1CM-476Z E CAPACITOR 47uF 16V M EU,EEC33 NDC31HJ-330X C CAPACITOR 33pF 50V J EU,EEC34 NDC31HJ-330X C CAPACITOR 33pF 50V J EU,EEC35 NDC31HJ-561X C CAPACITOR 560pF 50V J EU,EEC36 NCB31HK-331X C CAPACITOR 330pF 50V K EU,EE
Symbol No. Part No. Part Name Description Local
3-10
C37 QERF1CM-106Z E CAPACITOR 10uF 16V M EU,EEC52 NCB31HK-103X C CAPACITOR 0.01uF 50V KC53 NCB31HK-103X C CAPACITOR 0.01uF 50V KC54 QETN1EM-476Z E CAPACITOR 47uF 25V MC55 QETN1HM-105Z E CAPACITOR 1uF 50V MC56 QETN1HM-105Z E CAPACITOR 1uF 50V MC57 QETN1HM-105Z E CAPACITOR 1uF 50V MC61 QETN1HM-105Z E CAPACITOR 1uF 50V MC62 QETN1HM-105Z E CAPACITOR 1uF 50V MC63 QETN1HM-105Z E CAPACITOR 1uF 50V MC64 QETN1HM-105Z E CAPACITOR 1uF 50V MC65 QETN1HM-105Z E CAPACITOR 1uF 50V MC66 QETN1HM-105Z E CAPACITOR 1uF 50V MC71 NCB31HK-103X C CAPACITOR 0.01uF 50V KC72 NCB31HK-103X C CAPACITOR 0.01uF 50V KC111 NCB31HK-153X C CAPACITOR 0.015uF 50V KC112 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC113 NCB31HK-821X C CAPACITOR 820pF 50V KC120 QETN1HM-105Z E CAPACITOR 1uF 50V MC121 QETN1HM-105Z E CAPACITOR 1uF 50V MC122 QETN1HM-105Z E CAPACITOR 1uF 50V MC124 NCB31CK-104X C CAPACITOR 0.1uF 16V KC142 QETN1HM-105Z E CAPACITOR 1uF 50V MC151 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC152 NDC31HJ-101X C CAPACITOR 100pF 50V JC161 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC162 NDC31HJ-101X C CAPACITOR 100pF 50V JC165 NCB31HK-102X C CAPACITOR 1000pF 50V KC172 NFV81CM-105X MF CAPACITOR 1uF 16V MC173 NDC31HJ-101X C CAPACITOR 100pF 50V JC182 NFV81CM-105X MF CAPACITOR 1uF 16V MC183 NDC31HJ-101X C CAPACITOR 100pF 50V JC211 NCB31HK-153X C CAPACITOR 0.015uF 50V KC212 QEKC1HM-475Z E CAPACITOR 4.7uF 50V MC213 NCB31HK-821X C CAPACITOR 820pF 50V KC220 QETN1HM-105Z E CAPACITOR 1uF 50V MC221 QETN1HM-105Z E CAPACITOR 1uF 50V MC222 QETN1HM-105Z E CAPACITOR 1uF 50V MC224 NCB31CK-104X C CAPACITOR 0.1uF 16V KC242 QETN1HM-105Z E CAPACITOR 1uF 50V MC251 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC252 NDC31HJ-101X C CAPACITOR 100pF 50V JC261 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC262 NDC31HJ-101X C CAPACITOR 100pF 50V JC265 NCB31HK-102X C CAPACITOR 1000pF 50V KC272 NFV81CM-105X MF CAPACITOR 1uF 16V MC273 NDC31HJ-101X C CAPACITOR 100pF 50V JC282 NFV81CM-105X MF CAPACITOR 1uF 16V MC283 NDC31HJ-101X C CAPACITOR 100pF 50V JC321 QETN1EM-107Z E CAPACITOR 100uF 25V MC322 NCF31HZ-473X C CAPACITOR 0.047uF 50V ZC323 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC324 NCB31CK-104X C CAPACITOR 0.1uF 16V KC325 QETN1HM-226Z E CAPACITOR 22uF 50V MC341 NCB31CK-105X C CAPACITOR 1uF 16V KC342 NCB31CK-105X C CAPACITOR 1uF 16V KC343 NCB31CK-104X C CAPACITOR 0.1uF 16V KC344 NCB31CK-104X C CAPACITOR 0.1uF 16V KC351 QETN1HM-106Z E CAPACITOR 10uF 50V MC352 NCB31HK-102X C CAPACITOR 1000pF 50V KC361 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC362 NCB31CK-223X C CAPACITOR 0.022uF 16V KC363 NDC31HJ-101X C CAPACITOR 100pF 50V JC371 NCB31HK-103X C CAPACITOR 0.01uF 50V KC372 QETN1HM-106Z E CAPACITOR 10uF 50V MC373 QETN1HM-106Z E CAPACITOR 10uF 50V MC374 NCB31HK-103X C CAPACITOR 0.01uF 50V KC375 QETN1EM-476Z E CAPACITOR 47uF 25V MC376 QETN1HM-226Z E CAPACITOR 22uF 50V MC377 QETN1HM-225Z E CAPACITOR 2.2uF 50V MC378 QETN1HM-106Z E CAPACITOR 10uF 50V MC381 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC383 NDC31HJ-221X C CAPACITOR 220pF 50V JC384 NDC31HJ-221X C CAPACITOR 220pF 50V JC385 QETN1HM-106Z E CAPACITOR 10uF 50V MC386 NCB31HK-103X C CAPACITOR 0.01uF 50V KC701 NCB31CK-473X C CAPACITOR 0.047uF 16V K U,UN,AC702 NCB31HK-102X C CAPACITOR 1000pF 50V K
Symbol No. Part No. Part Name Description Local
C703 NCB30JK-105X C CAPACITOR 1uF 6.3V KC704 NCB30JK-105X C CAPACITOR 1uF 6.3V KC708 NDC31HJ-270X C CAPACITOR 27pF 50V JC709 NDC31HJ-220X C CAPACITOR 22pF 50V JC710 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC711 NCB31CK-104X C CAPACITOR 0.1uF 16V KC712 NCB31HK-102X C CAPACITOR 1000pF 50V KC721 NCB31HK-471X C CAPACITOR 470pF 50V KC731 NCB31HK-103X C CAPACITOR 0.01uF 50V KC732 QETN1EM-476Z E CAPACITOR 47uF 25V MC801 QETN1HM-106Z E CAPACITOR 10uF 50V MC802 NCB31HK-104X C CAPACITOR 0.1uF 50V KC803 QETN1AM-227Z E CAPACITOR 220uF 10V MC804 NCB31CK-104X C CAPACITOR 0.1uF 16V KC805 NCB31HK-103X C CAPACITOR 0.01uF 50V KC806 QETN1AM-227Z E CAPACITOR 220uF 10V MC807 QETN1HM-226Z E CAPACITOR 22uF 50V MC808 NCB31HK-102X C CAPACITOR 1000pF 50V KC809 NCB31CK-104X C CAPACITOR 0.1uF 16V KC811 QETN1HM-226Z E CAPACITOR 22uF 50V MC823 NCB31HK-104X C CAPACITOR 0.1uF 50V KC824 NCB31HK-472X C CAPACITOR 4700pF 50V KC827 QEZ0595-477Z E CAPACITOR 470uF 25V MC828 QEZ0595-477Z E CAPACITOR 470uF 25V MC829 NCB31HK-104X C CAPACITOR 0.1uF 50V KC830 NCB31CK-105X C CAPACITOR 1uF 16V KC831 QETN1AM-227Z E CAPACITOR 220uF 10V MC832 NCB31HK-103X C CAPACITOR 0.01uF 50V KC834 NCB31CK-104X C CAPACITOR 0.1uF 16V KC835 NCB31HK-103X C CAPACITOR 0.01uF 50V KC836 NCB31HK-103X C CAPACITOR 0.01uF 50V KC837 NCB31CK-104X C CAPACITOR 0.1uF 16V KC838 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC840 NCB31CK-105X C CAPACITOR 1uF 16V KC841 QETN1EM-476Z E CAPACITOR 47uF 25V MC844 QETN1EM-476Z E CAPACITOR 47uF 25V MC845 NCB31HK-104X C CAPACITOR 0.1uF 50V KC847 QETN1HM-226Z E CAPACITOR 22uF 50V MC848 NCB30JK-105X C CAPACITOR 1uF 6.3V KC849 NCB31HK-104X C CAPACITOR 0.1uF 50V KC853 QEZ0723-338 E CAPACITOR 3300uF 160V MC854 QETN1HM-225Z E CAPACITOR 2.2uF 50V MC855 QETM1EM-108 E CAPACITOR 1000uF 25V MC861 NCB31HK-104X C CAPACITOR 0.1uF 50V KC864 NCB31HK-104X C CAPACITOR 0.1uF 50V KC865 NCB31HK-104X C CAPACITOR 0.1uF 50V KC871 NCB31HK-472X C CAPACITOR 4700pF 50V KC872 NCB31HK-104X C CAPACITOR 0.1uF 50V KC873 NCJ11EK-106X-R C CAPACITOR 10uF 25VC873 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC874 NCJ11EK-106X-R C CAPACITOR 10uF 25VC874 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC875 NCB31HK-103X C CAPACITOR 0.01uF 50V KC876 QEZ0595-477Z E CAPACITOR 470uF 25V MC877 NCB31HK-103X C CAPACITOR 0.01uF 50V KC878 NCB31HK-103X C CAPACITOR 0.01uF 50V KC879 NCB31HK-103X C CAPACITOR 0.01uF 50V KC881 NCB31HK-103X C CAPACITOR 0.01uF 50V KC882 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3801 QETN1EM-107Z E CAPACITOR 100uF 25V MC3802 NCF31HZ-473X C CAPACITOR 0.047uF 50V ZC8033 NCB31CK-105X C CAPACITOR 1uF 16V KC8042 NCJ11EK-106X-R C CAPACITOR 10uF 25VC8042 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC8043 NCJ11EK-106X-R C CAPACITOR 10uF 25VC8043 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC8044 QETN1EM-476Z E CAPACITOR 47uF 25V MC8046 NCB31HK-222X C CAPACITOR 2200pF 50V KC8047 NCB31HK-682X C CAPACITOR 6800pF 50V KC8048 NDC31HJ-221X C CAPACITOR 220pF 50V JC8061 QETN1EM-476Z E CAPACITOR 47uF 25V MC8062 NCB21CK-105X C CAPACITOR 1uF 16V KC8063 NCB31EK-104X C CAPACITOR 0.1uF 25V KC8065 NCF21CZ-105X C CAPACITOR 1uF 16V ZC8066 NCF21HZ-105X C CAPACITOR 1uF 50V ZC8067 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8068 NCF21HZ-105X C CAPACITOR 1uF 50V ZC8069 QETN1EM-107Z E CAPACITOR 100uF 25V M
Symbol No. Part No. Part Name Description Local
3-11
C8071 NCB31CK-104X C CAPACITOR 0.1uF 16V KC8073 NCB31CK-104X C CAPACITOR 0.1uF 16V KC8074 NCB31HK-272X C CAPACITOR 2700pF 50V KC8075 NCB31CK-104X C CAPACITOR 0.1uF 16V KC8076 NCB31HK-103X C CAPACITOR 0.01uF 50V KC8091 QETN1EM-476Z E CAPACITOR 47uF 25V MC8092 NCB31CK-104X C CAPACITOR 0.1uF 16V KC8093 NCB31CK-105X C CAPACITOR 1uF 16V KC8501 QETN1HM-104Z E CAPACITOR 0.1uF 50V MC8605 QETN1EM-107Z E CAPACITOR 100uF 25V MC8607 NCB31HK-102X C CAPACITOR 1000pF 50V KC8701 NCB31HK-102X C CAPACITOR 1000pF 50V KC8801 NCB31HK-104X C CAPACITOR 0.1uF 50V K U,UN,AC8802 NCB31HK-104X C CAPACITOR 0.1uF 50V K
x4RA902 NRZ0065-102X NET RESISTOR 1kΩ 1/16W JRA903 NRZ0065-102X NET RESISTOR 1kΩ 1/16W JRA904 NRZ0065-151X NET RESISTOR 150ΩRA904 or NRZ0038-151X NET RESISTOR 150Ω 1/16W J
D3401 MA111-X SI DIODED3402 RB051L-40-X SB DIODED3501 MA111-X SI DIODED3701 RB521S-30-X SB DIODED3702 RB521S-30-X SB DIODED3703 MA8082/M/-X Z DIODED3704 LSQ971/KL/-X LEDD3705 LSQ971/KL/-X LEDD3706 RB521S-30-X SB DIODE
C1001 NCB31HK-392X C CAPACITOR 3900pF 50V KC1002 NDC31HJ-471X C CAPACITOR 470pF 50V JC1003 NCB31HK-471X C CAPACITOR 470pF 50V KC1101 NCB31HK-392X C CAPACITOR 3900pF 50V KC1102 NCB31HK-471X C CAPACITOR 470pF 50V KC1103 NCB31HK-471X C CAPACITOR 470pF 50V KC1201 NCB31HK-392X C CAPACITOR 3900pF 50V KC1202 NCB31HK-471X C CAPACITOR 470pF 50V KC1203 NCB31HK-471X C CAPACITOR 470pF 50V KC2001 NCB31HK-392X C CAPACITOR 3900pF 50V KC2002 NDC31HJ-471X C CAPACITOR 470pF 50V JC2003 NCB31HK-471X C CAPACITOR 470pF 50V KC2101 NCB31HK-392X C CAPACITOR 3900pF 50V KC2102 NCB31HK-471X C CAPACITOR 470pF 50V KC2103 NCB31HK-471X C CAPACITOR 470pF 50V KC2201 NCB31HK-392X C CAPACITOR 3900pF 50V KC2202 NCB31HK-471X C CAPACITOR 470pF 50V KC2203 NCB31HK-471X C CAPACITOR 470pF 50V KC3002 NBE41AM-476X TA E CAPACITOR 47uF 10V M
Symbol No. Part No. Part Name Description Local
C3003 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3006 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3007 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3008 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3009 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3010 NBE41CM-226X TA E CAPACITOR 22uF 16V MC3011 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3101 NCB31HK-331X C CAPACITOR 330pF 50V KC3102 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3103 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3106 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3107 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3108 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3109 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3110 NBE41CM-226X TA E CAPACITOR 22uF 16V MC3111 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3202 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3203 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3206 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3207 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3208 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3209 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3210 NBE41CM-226X TA E CAPACITOR 22uF 16V MC3211 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3401 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3505 NCB31HK-102X C CAPACITOR 1000pF 50V KC3506 NCB31HK-102X C CAPACITOR 1000pF 50V KC3507 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3508 NCB31CK-104X C CAPACITOR 0.1uF 16V KC3601 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3602 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3603 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3604 NCB31HK-102X C CAPACITOR 1000pF 50V KC3605 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3606 NBE41CM-226X TA E CAPACITOR 22uF 16V MC3607 NBE41CM-226X TA E CAPACITOR 22uF 16V MC3608 NBE41AM-476X TA E CAPACITOR 47uF 10V MC3610 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3611 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3612 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3701 NEAF1CM-226X E CAPACITOR 22uF 16V MC3702 NCB31CK-105X C CAPACITOR 1uF 16V KC3703 NCJ11EK-106X-R C CAPACITOR 10uF 25VC3703 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC3704 NCJ11EK-106X-R C CAPACITOR 10uF 25VC3704 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC3705 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3706 NCJ11EK-106X-R C CAPACITOR 10uF 25VC3706 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC3707 NEAF1CM-226X E CAPACITOR 22uF 16V MC3708 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3709 NEAF1CM-226X E CAPACITOR 22uF 16V MC3710 NCB31CK-105X C CAPACITOR 1uF 16V K
D401 RB521S-30-X SB DIODED402 MA111-X SI DIODED403 MA111-X SI DIODED404 MA111-X SI DIODED502 MC2836-X DIODED503 MA111-X SI DIODED504 MA111-X SI DIODED505 MA111-X SI DIODED506 MA111-X SI DIODE
Symbol No. Part No. Part Name Description Local
D507 MA111-X SI DIODED508 MA111-X SI DIODED509 MA111-X SI DIODED510 MA111-X SI DIODED521 MC2838-X DIODED4301 RB521S-30-X SB DIODED4302 RB521S-30-X SB DIODED4703 MA111-X SI DIODED4704 MA8047/M/-X Z DIODED4705 MA8047/M/-X Z DIODED4706 MA8047/M/-X Z DIODED4707 BAV99L-X SI DIODED4708 MA8047/M/-X Z DIODED4709 BAV99L-X SI DIODED4901 LSQ971/KL/-X LEDD4902 SML310BA1T/HJ-X LEDD4903 SML310BA1T/HJ-X LEDD4904 SML310BA1T/HJ-X LEDD4905 SML310BA1T/HJ-X LEDD4906 SML310BA1T/HJ-X LEDD4907 SML310BA1T/HJ-X LEDD4908 SML310BA1T/HJ-X LEDD4909 SML310BA1T/HJ-X LEDD4910 SML310BA1T/HJ-X LED
C401 NCB20JK-106X C CAPACITOR 10uF 6.3V KC402 NCB20JK-106X C CAPACITOR 10uF 6.3V KC403 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC404 NCB30JK-105X C CAPACITOR 1uF 6.3V KC405 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC406 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC407 NCB31CK-224X C CAPACITOR 0.22uF 16V KC408 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC409 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC410 NCB31CK-224X C CAPACITOR 0.22uF 16V KC413 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC414 NCB30JK-105X C CAPACITOR 1uF 6.3V KC415 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC416 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC417 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC418 NCBA1AK-473W C CAPACITOR 0.047uF 10V KC419 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC420 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC421 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC422 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC423 NBE21CM-106X TA E CAPACITOR 10uF 16V MC424 NDC31HJ-390X C CAPACITOR 39pF 50V JC425 NDC31HJ-390X C CAPACITOR 39pF 50V JC426 NDC31HJ-390X C CAPACITOR 39pF 50V JC427 NCB20JK-106X C CAPACITOR 10uF 6.3V KC428 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC430 NCB31AK-474X C CAPACITOR 0.47uF 10V KC431 NCBA1HK-102W C CAPACITOR 1000pF 50V KC432 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC433 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC434 NDCA1HJ-100W C CAPACITOR 10pF 50V JC435 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC436 NCB31CK-224X C CAPACITOR 0.22uF 16V KC438 NCB30JK-105X C CAPACITOR 1uF 6.3V KC439 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC440 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC442 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC443 NBE41AM-476X TA E CAPACITOR 47uF 10V MC444 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC445 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC446 NCB30JK-105X C CAPACITOR 1uF 6.3V KC447 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC448 NCB21AK-225X C CAPACITOR 2.2uF 10V KC450 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC481 NCB20JK-106X C CAPACITOR 10uF 6.3V KC482 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC483 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC485 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC486 NCB31HK-392X C CAPACITOR 3900pF 50V KC487 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC501 NBE20JM-476X TA E CAPACITOR 47uF 6.3V MC502 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC503 NCBA1AK-104W C CAPACITOR 0.1uF 10V K
Symbol No. Part No. Part Name Description Local
3-18
C504 NCB31CK-473X C CAPACITOR 0.047uF 16V KC505 NCB31CK-473X C CAPACITOR 0.047uF 16V KC506 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC507 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC508 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC509 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC510 NCB30JK-105X C CAPACITOR 1uF 6.3V KC511 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC512 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC513 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC514 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC515 NCBA1AK-473W C CAPACITOR 0.047uF 10V KC516 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC517 NCBA1AK-473W C CAPACITOR 0.047uF 10V KC518 NDC31HJ-471X C CAPACITOR 470pF 50V JC519 NCBA1AK-473W C CAPACITOR 0.047uF 10V KC520 NCB20JK-106X C CAPACITOR 10uF 6.3V KC522 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC601 NCB20JK-106X C CAPACITOR 10uF 6.3V KC602 NCB31CK-105X C CAPACITOR 1uF 16V KC603 NCB31CK-105X C CAPACITOR 1uF 16V KC604 NCB31CK-105X C CAPACITOR 1uF 16V KC605 NCB20JK-106X C CAPACITOR 10uF 6.3V KC606 NDCA1HJ-180W C CAPACITOR 18pF 50V JC607 NDCA1HJ-180W C CAPACITOR 18pF 50V JC608 NDCA1HJ-101W C CAPACITOR 100pF 50V JC609 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC610 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC611 NDCA1HJ-101W C CAPACITOR 100pF 50V JC612 NCB30JK-105X C CAPACITOR 1uF 6.3V KC613 NDCA1HJ-101W C CAPACITOR 100pF 50V JC614 NCB30JK-105X C CAPACITOR 1uF 6.3V KC615 NDCA1HJ-101W C CAPACITOR 100pF 50V JC616 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC617 NCB31HK-103X C CAPACITOR 0.01uF 50V KC618 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC619 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC620 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC621 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC622 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC623 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC624 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC625 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC626 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC627 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC628 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC629 NCB20JK-106X C CAPACITOR 10uF 6.3V KC630 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC631 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC632 NDCA1HJ-101W C CAPACITOR 100pF 50V JC633 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC634 NCB30JK-105X C CAPACITOR 1uF 6.3V KC635 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC636 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC637 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC638 NCB30JK-105X C CAPACITOR 1uF 6.3V KC639 NDCA1HJ-101W C CAPACITOR 100pF 50V JC640 NCB30JK-105X C CAPACITOR 1uF 6.3V KC641 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC642 NCB20JK-106X C CAPACITOR 10uF 6.3V KC643 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC644 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC645 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC646 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC647 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC648 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC649 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC650 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC651 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC652 NCB20JK-106X C CAPACITOR 10uF 6.3V KC653 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC654 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC655 NCB20JK-106X C CAPACITOR 10uF 6.3V KC656 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4101 NBE20JM-476X TA E CAPACITOR 47uF 6.3V MC4102 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4103 NCB30JK-105X C CAPACITOR 1uF 6.3V KC4104 NCBA1AK-104W C CAPACITOR 0.1uF 10V K
Symbol No. Part No. Part Name Description Local
C4105 NBE20JM-476X TA E CAPACITOR 47uF 6.3V MC4106 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4107 NCBA1HK-102W C CAPACITOR 1000pF 50V KC4108 NCB30JK-105X C CAPACITOR 1uF 6.3V KC4110 NBE20JM-476X TA E CAPACITOR 47uF 6.3V MC4111 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4118 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4119 NCB31HK-152X C CAPACITOR 1500pF 50V KC4120 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4121 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4201 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4201 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4202 NCB31CK-104X C CAPACITOR 0.1uF 16V KC4203 NCJ21CK-106X-R C CAPACITOR 10uF 16V KC4204 NCB31CK-104X C CAPACITOR 0.1uF 16V KC4205 NCB31CK-104X C CAPACITOR 0.1uF 16V KC4206 NCB31CK-104X C CAPACITOR 0.1uF 16V KC4207 NCB20JK-475X C CAPACITOR 4.7uF 6.3V KC4208 NCB31CK-105X C CAPACITOR 1uF 16V KC4301 NQR0450-001X EMI FILTER 0.022uF 50V MC4302 NQR0450-001X EMI FILTER 0.022uF 50V MC4303 NCB31CK-104X C CAPACITOR 0.1uF 16V KC4304 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4305 NCB31HK-104X C CAPACITOR 0.1uF 50V KC4306 NCB31CK-104X C CAPACITOR 0.1uF 16V KC4307 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4308 NBE20JM-476X TA E CAPACITOR 47uF 6.3V MC4309 NBE41AM-476X TA E CAPACITOR 47uF 10V MC4310 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4310 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4311 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4311 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4312 NCJ21CK-106X-R C CAPACITOR 10uF 16V KC4313 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4314 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4315 NDCA1HJ-100W C CAPACITOR 10pF 50V JC4316 NDCA1HJ-100W C CAPACITOR 10pF 50V JC4317 NDCA1HJ-100W C CAPACITOR 10pF 50V JC4318 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4319 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4320 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4321 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4322 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4323 NDCA1HJ-180W C CAPACITOR 18pF 50V JC4701 NQR0450-001X EMI FILTER 0.022uF 50V MC4706 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4707 NCB30JK-105X C CAPACITOR 1uF 6.3V KC4709 NCB21AK-225X C CAPACITOR 2.2uF 10V KC4710 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC4711 NCB31AK-474X C CAPACITOR 0.47uF 10V KC4712 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4713 NDCA1HJ-101W C CAPACITOR 100pF 50V JC4714 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4715 NCB31HK-473X C CAPACITOR 0.047uF 50V KC4717 NDC31HJ-221X C CAPACITOR 220pF 50V JC4718 NDCA1HJ-101W C CAPACITOR 100pF 50V JC4719 NDCA1HJ-101W C CAPACITOR 100pF 50V JC4720 NCB31HK-682X C CAPACITOR 6800pF 50V KC4720 or NDC31EJ-682X C CAPACITOR 6800pF 25V JC4721 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC4722 NDCA1HJ-101W C CAPACITOR 100pF 50V JC4723 NDCA1HJ-101W C CAPACITOR 100pF 50V JC4724 NCB31HK-473X C CAPACITOR 0.047uF 50V KC4725 NCB31HK-473X C CAPACITOR 0.047uF 50V KC4726 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4726 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4727 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4727 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4728 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4728 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4729 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4729 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4730 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4730 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4731 NCB11CK-225X C CAPACITOR 2.2uF 16V KC4732 NCB31HK-473X C CAPACITOR 0.047uF 50V KC4733 NCZ1011-220X C CAPACITOR 22pFC4734 NCB31HK-333X C CAPACITOR 0.033uF 50V K
Symbol No. Part No. Part Name Description Local
3-19
C4735 NCB31HK-392X C CAPACITOR 3900pF 50V KC4736 NCF21HZ-105X C CAPACITOR 1uF 50V ZC4737 NCF21HZ-105X C CAPACITOR 1uF 50V ZC4738 NCJ11EK-106X-R C CAPACITOR 10uF 25VC4738 or NCJ11EK-106X-A C CAPACITOR 10uF 25V KC4901 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC5001 NCB20JK-475X C CAPACITOR 4.7uF 6.3V K
Packing materials and accessories parts listBlock No. M MM3
P5
A7
P2
P2
A,U,UN
EU,EE
A1, A2, A3,A6, A16
A1, A2, A3
E,EU,U
P2
P4
P6
A4, A5
A14
P3
KIT: A8, A9, A10
A12
A11
A13
P7
P1
No additional / supplemental order of WARRANTY CARDs are available
The parts without symbol number are not service.
A15
3-26
Packing and AccessoriesBlock No. [M][3][M][M]
Symbol No. Part No. Part Name Description Local
A 1 LVT1669-001A INST BOOK ENG FRE SPA EUA 1 LVT1669-003A INST BOOK ENG RUS UKR EEA 1 LVT1670-002A INST BOOK ENG CHI(TAIWAN) THA UA 1 LVT1670-004A INST BOOK ENG INA UNA 1 LVT1670-001A INST BOOK ENG AA 2 LVT1669-004A INSTALL MANUAL ENG FRE SPA EUA 2 LVT1669-006A INSTALL MANUAL ENG RUS UKR EEA 2 LVT1670-006A INSTALL MANUAL ENG CHI(TAIWAN) THA UA 2 LVT1670-008A INSTALL MANUAL ENG INA UNA 2 LVT1670-005A INSTALL MANUAL ENG AA 3 LVT1672-001A INST SHEETA 4 LVT1669-002A INST BOOK PER TUR EUA 4 LVT1670-003A INST BOOK ARA KOR PER UA 5 LVT1669-005A INSTALL MANUAL PER TUR EUA 5 LVT1670-007A INSTALL MANUAL ARA KOR PER UA 6 ------------ WARRANTY CARD BT-54032-1 EU,EEA 7 LV44661-003A CAUTION SHEET EU,EEA 7 LV44661-004A CAUTION SHEET U,UN,AA 8 QYSDSP5008ZA SCREW M5 x 8mm(x8)A 9 QYSSSP5008ZA SCREW M5 x 8mm(x8)A10 LV41478-001A CORD CONNECTER (x2)A11 RM-RK251 REMOCONA12 ------------ BATTERY (x2)A13 QAM1005-003 CAR CABLE EU,EEA13 QAM1005-004 CAR CABLE U,UN,AA14 LV22463-002A TRIM PLATE EU,EEA14 LV22464-001A TRIM PLATE(NIS) U,UN,AA15 QAL0980-001 ANTENNAA16 VND3046-001 SERIAL TICKET EU,EEKIT SRW-AVX800E SCREW PARTS KIT A8 A9 A10P 1 LV37483-001A CARTON EUP 1 LV37485-001A CARTON EEP 1 LV37487-001A CARTON U,UN,AP 2 FSPG4002-001 POLY BAG (x2) EU,UP 2 FSPG4002-001 POLY BAG EE,UN,AP 3 QPA00801205 POLY BAG 8cm x 12cmP 4 FSPG4002-001 POLY BAGP 5 QPC03504015P POLY BAG 35cm x 40cmP 6 LV11394-002A CUSHION TOP(E) EU,EEP 6 LV11396-003A CUSHION TOP U,UN,AP 7 LV11395-002A CUSHION BOT(E) EU,EEP 7 LV11397-002A CUSHION BOTTOM U,UN,A