-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
1/15
My Blog
Thoughts, projects, hacks and whatever else springs to mind
Japanese import FM tuner conversion
28 MARCH 2010 36
COMMENTS(HTTP://NZLAMB.WORDPRESS.COM/2010/03/28/JAPANESE-IMPORT-FM-TUNER-CONVERSION/#COMMENTS)
This post describes how to modify a McIntosh PF-2142I (often but
incorrectly referred to as PF-21421)
JDM car radio to natively tune from 87.5-108MHz as used in most
countries around the world. This
model of radio is fitted as standard equipment in many JDM
Subaru Legacy and Outback carsmanufactured between 1998 and
2003.
Most Japanese domestic market import car radios are designed to
tune from 76-90MHz which means
they will not work natively in any other country. You can of
course buy a so-called band expander but
these usually result in nasty RF harmonics, poor reception and
reduced sound quality. They also stillrestrict you to a 14MHz
segment of the 20MHz public FM band and dont display the
correct
frequency on the radio. This modification allows the radio to
tune local station and display the correct
frequency without the need for a band expander!
Update: Ive also added a more generic guide here
(http://nzlamb.wordpress.com/2010/07/02/a-guide-to-hacking-japanese-car-radios/).
The information here certainly applies to virtually any Clarion
or McIntosh JDM radio using a Clarion80-2082AT tuner module. Ive
also successfully applied this to the Clarion PF-1572I and PF-2143I
aswell. Most minidisc players are designed specifically for the JDM
only and cannot be modified.
This modification works because Clarion (and other
manufacturers) often produce a base head unitdesign for the
international market. The FM band it can tune is simply set by
using a specific tunermodule and setting the right jumpers to
match. While Im sure Im not the first person to have figured
this out, I dare say its the first time someone had decided to
publish this information freely on theinternet!
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
2/15
(http://nzlamb.files.wordpress.com/2010/03/before_modification.jpg)
What you need:
#0 Philips screwdriver
Small flat blade screwdriverFine tipped, temperature controlled
soldering ironFile solderDesoldering toolDesoldering wickSmall side
cutters
4x Sanyo SVC203 varicaps (available from Farnell
(http://www.farnell.com) and other suppliers)Suitable plug to
connect power, etc to the stereoExperience with SMD soldering
If you are modding a McIntosh like this one you will also need a
suitable amplifier for bench testing asthe stereo does not have one
inside it. Any type will do; simply use pins 1 and 3 for audio and
6 forground on the 13-pin audio output connector.
Disassembly
Remove the top screw and pry the top cover off using flat
screwdriver in each of the four slots. Do thesame for the bottom
cover.
Remove the volume and fader knobs followed by front panel. It is
attached via two black clips on each
side. Use a small flat screwdriver to push these inwards and
carefully slide the panel off. Try to do thisevenly to avoid
damaging the connectors.
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
3/15
(http://nzlamb.files.wordpress.com/2010/03/front-panel-clips.jpg)
Disconnect the ribbon cable from the front then remove the four
screws holding the CD player modulein. These are the top two screws
on each side of the unit. Lift the CD player out from the top.
(http://nzlamb.files.wordpress.com/2010/03/cd-player-screws.jpg)
Remove the screw from the each side of the lower rear panel.
Leave the panel in place for now.
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
4/15
(http://nzlamb.files.wordpress.com/2010/03/rear-
panel2.jpg)
Remove the remaining two screws on each side of the unit. The
outer sides and upper rear panel shouldnow lift off the base in one
piece.
Undo the four screws holding the cassette desk in and carefully
lift it out.
(http://nzlamb.files.wordpress.com/2010/03/cassette-
deck.jpg)
(http://nzlamb.files.wordpress.com/2010/03/cassette-removed.jpg)
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
5/15
Modifications
Locate the area selection jumpers. Move the jumper shown in the
photo to select area 2 (NZ and mostother countries). Move the
jumper to the right instead instead to select area 1 (North
America). The rest
of the modification is the same regardless of area.
(http://nzlamb.files.wordpress.com/2010/03/jumper-
before.jpg)
(http://nzlamb.files.wordpress.com/2010/03/jumper-after.jpg)
Desolder and remove the metal bracket that runs across the
middle of the PCB.
Desolder and remove the tuner module. This is quite difficult
and time consuming! You may need toloosen the volume pot in order
to get the tuner out.
Replace the four varicaps on the tuner PCB with SVC203 types.
The original varicaps usually bear the
marking V4 or F0.
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
6/15
(http://nzlamb.files.wordpress.com/2010/03/varicaps.jpg)
Desolder the tuner shield and remove it.
Locate the small black coil shown in the photo and desolder
it.
(http://nzlamb.files.wordpress.com/2010/03/tuner-
coil.jpg)
Note that it has three terminals; only two are used. Cut the
wire leading to the top of the coil andremove one and a half turns.
Solder the wire to the previously unused terminal. Solder the coil
back in
place. The photo below shows the modified coil installed back
into the tuner.
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
7/15
(http://nzlamb.files.wordpress.com/2010/03/tuner-coil-after.jpg)
Reattach and solder the shield to the tuner. Install the tuner
back onto the main board.
Testing and Adjusting
Im not exactly a radio buff so heres how to adjust the radio the
kludgy way without any fancy testinstruments! If you are a bit more
clued up in this area you might have a better way of doing
this.
Attach the front panel being careful not to damage the two
connectors. It should sit in place withoutany additional support
but be careful not to knock it.
Connect power, an amplifier and an antenna to the stereo and
confirm that the FM tuner now searchesthe frequency range you
expected. Try auto seeking for an FM station. The tuner should do
thisquickly but may not lock onto a station by itself at this
stage. If it suddenly slows down you need toretune the coil in the
tuner as described in the previous section. Remove more winding to
shift the
reception up the band.
If all is well tune manually into a local station and confirm it
sounds OK and gets stereo reception.
Mark the position of the top coil indicated in the photo. Tune
into a known weak station. Slowly adjustthe coil until the signal
appears to be at its peak. You will probably find this is close to
its maximumclockwise position. Be careful not to over tighten it as
it is very easy to damage; the moment you feel
the slightest change in resistance on the screwdriver you have
reached the maximum.
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
8/15
(http://nzlamb.files.wordpress.com/2010/03/coils.jpg)
Now try seeking stations. You may find this works OK for strong
stations at the lower end of the bandand then gives up. Use a small
plastic object to widen the gap of the lower coil marked in the
photo. Dothis in small increments until the radio seeks properly
across the entire band (or as much as possible).
Once down, power cycle the radio and confirm it still appears to
operate at its peak performance andthat the stereo indicator comes
on when you tune into a sufficiently strong station.
Once you are happy with the radios performance, take a moment to
rework the solder joints where themetal chassis components are
soldered to the PCB, and also the joins on and around Q408, Q423
andQ424 as these can often crack a little over time.
Finally Id recommend checking that all of the features (CD
player, controls, backlight, etc) still workas expected before
installing it into a car!
(http://nzlamb.files.wordpress.com/2010/03/after-modification.jpg)
If you install the modified radio into a Japanese import car the
reception may not be as good as you
would get from a car produced for the local market. This is
because the antennas in JDM cars areusually tuned for the 76-90MHz
range and often use horizontal polarisation.
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
9/15
LP-2020A+ Lepai Tripath Class-T Hi-Fi $34.99$18.02
FILED UNDER CAR AUDIO, HACKS, HOW TO TAGGED WITH CAR AUDIO,
CLARION,HACKS, MCINTOSH, MODS, SUBARU
36 Responses to Japanese import FM tuner conversion
Perry says:15 June 2010 at 00:19i have on hand a EF-1080I, i not
own subaru. if you know can tell me green connector pins
layoutspeakers/power..etc. Thanks so much!
Replynzlamb says:17 June 2010 at 22:52See this post.
Replymat says:1 July 2010 at 18:50can this conversion make with
PF-40251-C..mcintosh with MD slot.
Replynzlamb says:1 July 2010 at 19:11No it wont work on most MD
models including the PF-4025I.
ReplyPingback: A guide to hacking Japanese car radios My
Blog
Vince says:3 August 2010 at 05:58
Do you have a manual for a PF-2142I.
About these ads (http://en.wordpress.com/about-these-ads/)
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
10/15
Do you have a manual for a PF-2142I.
I would really appreciate it.Thank you.
Replynzlamb says:6 August 2010 at 08:26Sorry no I dont have one,
but I sure wish I did!
ReplyCameron says:
25 November 2010 at 11:04It seems the varicap replacement isnt
needed if you have F0 varicaps, Ive ordered my SVC203s,but Im
sitting here listening to 99.0 FM, without changing them clear as
day.
Replynzlamb says:25 November 2010 at 18:08
Yes it does work fine with the original varicaps but you will
likely find you wont be able toreliably tune the entire 87.5-108MHz
range due to the limited capacitance range of the originals.Try
tuning into stations towards each end of the band and see what
happens.
ReplyCameron says:26 November 2010 at 10:09I can reliably tune
100.6, and 88.6, the two most extreme end stations that can be
received
around here The only problem I have is unreliable seeking from
around 95.0 upwards, butthat may be to do with the coil that had to
be stretched?
Joshua Collins says:7 August 2012 at 02:59hello have you ever
tryed changing a panasonic cq-tx5500d to recive from 87.5-108MHz
asused in the UK? what contry are you located in?
thanks
nzlamb says:
26 November 2010 at 18:04Thats awesome! You might find it tapers
off at 104 or so but thats pretty decent as it stands. Andyes,
stretching that coil should cure the seeking problem.
Replyjesse says:20 July 2011 at 12:00i have on hand a PF-1242I,
i not own subaru. if you know can tell me green connector pins
layout
speakers/power..etc. Thanks so much!
Reply
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
11/15
Saab93 says:2 January 2012 at 01:45Hi !
What analog can be user as EF-1080I ?
May be other model Clarion ampfilier ?
ReplyPingback: Addzest DRX9255 Tuner - DIYMA.com - Scientific
Car Audio - Truth in Sound Quality
joe says:13 April 2012 at 03:01will this work on jvc car
stereo
ReplyJos Fabio Lou says:20 July 2012 at 06:22
Hi, can you help me, can you describe what is the right jumper
for North America? and if you havethe diagram of this radio?
Reply
Francis Otieno says:22 October 2012 at 22:47Am in kenya and the
so called fm expander are so irritating. Mine is a toyota ISIS.
what do i do?
ReplyDanny says:18 November 2012 at 13:50
Do you know where to buy the scv303 varicap in Australia or the
net. I have been looking but havehad no luck so far. I have done
everything discribed but am waiting to find a suitable varicap.
ReplyDanny says:18 November 2012 at 13:51Svc203*
Replynzlamb says:3 December 2012 at 18:27
Looks like Element14 no longer stock them. Mouser and Digikey do
but the minimum orderquantity is 3000 parts. If I find something
Ill post it.
ReplyMatthew says:9 February 2013 at 09:44
Hey I just bought a 2000 Subaru outback with a mcintosh pf-2142i
headunit and a ef-1080i amp
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
12/15
Hey I just bought a 2000 Subaru outback with a mcintosh pf-2142i
headunit and a ef-1080i ampaswell as the four door speakers and the
sub. Im taking it all out and replacing it but Im confused.
If the 13 pin DIN conector was the output to the amp what was
the other rectangle connector for?And to wire the new head unit
directly do the speakers which wires would I have to connect it
to,The ones under the seat or in the dash? Also there is a conector
in front of the right hand door belowthe fuse box is that to do
with it aswell?
Matt.
Replynzlamb says:9 February 2013 at 15:54
The rectangle connector is CeNET for connecting to a CD Stacker
or TV tuner (both werefactory options). You can also buy interfaces
to connect iPods, auxiliary inputs and evenBluetooth to the factory
head unit via this connector.
To wire in a new head unit you will need to connect the speakers
via the plug under the seat.You can use the old head unit to amp
cable to pull new speaker wires under the carpet.
ReplyMatthew says:9 February 2013 at 17:07Still a lot tile
unsure sorry. So the speakers that are in place now run directly to
the whiteconector under the seat? And the rectangle one I was
talking about is identical to the oneunder the seat and came from
the back of the head unit. But what confused me was thatwhen I
tested it there was continuity between the corresponding pins on
the two identical
connectors (under the seat and in the dash) and I dont see why
the output of the amp wouldbe connected back to the head unit.
Thanks for your help!Matt.
nzlamb says:9 February 2013 at 17:45Its possible that the
connectors under the seat and for the head unit are wired together,
butnot according to the service manual. There is no amp in the head
unit; the speakers should
be directly connected to the amp under the seat. The speaker
wires still exist in the dashwiring (easier for Subaru to use a
common harness) but are not normally connected at thedoor
plugs.
In any case the pinout of each connector is quite different
despite the fact they use the sametype of plug.
Id suggest buying a Subaru adapter for your head unit to save
cutting the harness and seewhat happens when its connected. If the
speakers work then theres nothing to worry about.If the speakers
dont go then you will need to run some wires under the seat from
the headunit yourself, or change the door speaker wires over to the
standard harness at each doorconnector.
Matthew says:
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
13/15
9 February 2013 at 22:29Turns out the continuity was only
between power pins. now I have put both my subs in theboot and four
new speakers in the doors. Tomorrow Im going to run speaker wire
accross
and down the side of the seat to join the conector. I couldnt
seem to pull the exsisting cableunder the carpet and I have other
cables for the subs running that way so it seems easier.Thanks
again for your help your pin out diagrams of the amp were very
helpful and Iprobably couldnt have done it without
you.CheersMatt.
jala says:3 May 2013 at 03:36Hi, modifications done without
varicaps (hard to find from stores) radio can scan entire
87.5-108MHz range but i cant find any stations? what i done
wrong?
Replynzlamb says:
3 May 2013 at 11:40Measure the VT pin; you will likely notice
that its stuck at around 8v which means its unable totune across
the band and is stuck on a single frequency. The display simply
shows whatfrequency the microcontroller is instructing the PPL chip
to tune to. If the PLL cant do as askeddue to the LC side of it
being way off the mark it will simply give up and the radio will
sit at theextreme end of whatever range its currently tuned to.
You can partially fix this by modifying the coil but the radio
will never be able to cover theentire 87.5-108MHz band with the
original varicaps fitted as they dont have a wide enoughcapacitance
range.
Replyharold996tt says:8 June 2013 at 02:15Hi NZLamb,
Great site. Have just picked up this head unit and the
associated amp from eBay (Japanese domesticdismantled) and intend
on installing it in my Australian 1990 MX5 (I want the retro look
on thecheap and these look so perfectly retro). I gather that the
connectors are non standard on the headunit and amplifier (Subaru
specific). As the connectors were all cut off the amp and the head
unit,do you happen to know where I can source these from readily?
If you have any contacts that Icould purchase them off it would be
most appreciated. Much thanks in advance.
Replyharold996tt says:8 June 2013 at 04:55Apologies, I meant
output for the amp.
Reply
nzlamb says:
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
14/15
8 June 2013 at 19:54Yes they are Subaru specific. They are quite
commonly available from wrecking yards (at leastin NZ). If you cant
find an amp plug just use a head unit one and ensure you follow the
correctpinout. Worst case I might be able to track something down
locally.
Reply
tonysworkstuff says:22 July 2013 at 16:32Hi there, excellent
info, thanks! My 2142 (in a 2000 B4) has trouble with the front
panel buttons notalways working & the display showing
hieroglyphics, otherwise it still sounds fine. Off the top ofyour
head do you know how its connected to the PCB? I dont have a spare
on hand & just want tobe prepared when I pull it out to have a
go a fixing or replacing it. Cheers.
ReplyJohn says:1 January 2014 at 14:19Hi Nz lamb
Great write up on hacking these head units. unfortunately I dont
have the skills, knowledge orequipment to tackle this job, even
though Id really like my head unit to be able to do what your
does. Would u consider having a crack at my one for some
cash?Cheers
Replynzlamb says:10 January 2014 at 17:13Hi John, what type of
stereo do you have? The varicaps I used for replacements dont seem
to be
available any more. I could probably look into something similar
though. The job itself takes afew hours as it involves pretty much
tearing the stereo right down.
Replyjohn says:11 January 2014 at 08:22gidday
Ive got the Macintosh stereo from a 05 Lecagy wagon(Japanses
domestic model) Im prettysure its the newer one of the same model
mentioned you modified in your hack article.
Id be able to remove the stereo from the car no problem, just
from there actually modifyingthe electronics id have no idea.
Thats a buyer about the parts not being available. Im quite
surprised there isnt a market fora service like this, seems to me
in NZ with so many import vehicles coming to every year it
would be a commonly requested service.
nzlamb says:11 January 2014 at 08:27
Those later units are much easier to modify no replacement parts
(such as varicaps) are
-
2/28/14 Japanese import FM tuner conversion | My Blog
nzlamb.wordpress.com/2010/03/28/japanese-import-fm-tuner-conversion/
15/15
Those later units are much easier to modify no replacement parts
(such as varicaps) areneeded. Theres just a couple of coils to
tweak and a jumper to change. I did modify one butdidnt get photos
I may have an opportunity soon to modify another so Ill post a
how-toguide.
Blog at WordPress.com.
The Enterprise Theme.
Follow
Follow My Blog
Powered by WordPress.com