Top Banner
00400056E Common Rail System for ISUZU SERVICE MANUAL OPERATION 4HK1 / 6HK1 Type Engine February, 2004 Diesel Injection Pump
48
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: izuzu_4hk1

00400056E

Common Rail System for ISUZU

SERVICE MANUAL

OPERATION4HK1 / 6HK1 Type Engine

February, 2004

Diesel Injection Pump

Page 2: izuzu_4hk1

FORWARD

To meet the high pressurization requirements for the engine to deliver cleaner exhaust gas emissions, lower fuelconsumption and reduced noise, advanced electronic control technology is being adopted in the fuel injection system.This manual covers the electronic control model Common Rail system with HP3/HP4 pump for the ISUZU 4HK1/6HK1type engines which are used to ELF and GM 560 series respectively. Complex theories, special functions andcomponents made by manufacturers other than DENSO are omitted from this manual.This manual will help the reader develop an understanding of the basic construction, operation and system configurationof the DENSO manufactured components and brief diagnostic information.

TABLE OF CONTENTS

1. Product Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1-1. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2. System Components Parts Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2-1. Outline of System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-2. Outline of System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-3. Fuel System and Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Construction and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-1. Description of Main Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-2. Description of Control System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3-3. Various Types of Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243-4. Engine ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Page 3: izuzu_4hk1

-1-

1. Product Application1-1. Application

1-2. System Components Parts Numbers

Vehicle Name Engine Model Vehicle model Exhaust Volume Reference

ELF 4HK1 N series 5.2L Direct-Injection

C560 Series 6HK1 GM 560 7.8L Direct-Injection

Parts Name DENSO Parts NumberCar Manufacturer Parts

NumberReference

Supply Pump 294000-0260 8973288860 4HK1

294050-0021 9876020491 6HK1

Injector 095000-5351 8976011561 6HK1

095000-5361 8976028031

095000-5471 8973297031 4HK1

Rail 095440-0351 8973060632 4HK1

095440-0470 8973230190 6HK1

Engine ECU 275800-2801 8151794773 6HK1

275800-2812 8973750190 4HK1

275800-2822 8973750200

Page 4: izuzu_4hk1

2. Outline2-1. Outline of System

• The common rail system was developed primarily to cope with exhaust gas regulations for diesel engines, and aimed for

1. further improved fuel economy; 2. noise reduction; and 3. high power output.

A. System Characteristics• The common rail system uses a type of accumulation chamber called a rail to store pressurized fuel, and injectors that

contain electronically controlled solenoid valves to spray the pressurized fuel into the cylinders.

• Because the engine ECU controls the injection system (including the injection pressure, injection rate, and injection tim-

ing), the injection system is unaffected by the engine speed or load.

• This ensures a stable injection pressure at all times, particularly in the low engine speed range, and dramatically decreas-

es the amount of black smoke ordinarily emitted by a diesel engine during start-up and acceleration.

• As a result, exhaust gas emissions are cleaner and reduced, and higher power output is achieved.

a. Injection Pressure Control

• Enables high-pressure injection even at low engine speeds.

• Optimizes control to minimize particulate matter and NOx emissions.

b. Injection Timing Control

Enables finely tuned optimized control in accordance with driving conditions.

c. Injection Rate Control

Pilot injection control sprays a small amount of fuel before the main injection.

d. EGR (Exhaust Gas Recirculation) Control

By recirculating the exhaust gas into the intake side of the engine, the combustion temperature is reduced and NOx is

decreased.

Common Rail System

Optimization Pilot Injection

Maininjection

Injection Pressure Control Injection Timing Control Injection Rate Control

Injection Quantity Control

InjectionPressure

Speed Speed

Crankshaft Angle

ConventionalPump

Common Rail System

ConventionalPump

Common Rail System

Cylinder InjectionVolume Correction

Optimization, High Pressurization

Inje

ctio

n P

ressu

re

Inje

ctio

n T

imin

g

Pa

rtic

ula

te

Sp

ee

dIn

jectio

n R

ate

QD0734E

NO

x

-2-

Page 5: izuzu_4hk1

B. Comparison to the Conventional System

System

Common Rail System

Injection Quantity Control Pump (Governor)

Injection Timing Control Pump (Timer)

Rising Pressure Pump

Distributor Pump

Injection Pressure Control Dependent upon Speed and Injection Quantity

High-pressure Pipe

Momentary High Pressure

NozzleGovernor

Timer

In-line Pump

VE Pump

Rail

Usually High PressureSupply Pump

Injector

*1 TWV: Two Way Valve *2 SCV Suction Control Valve QD2341E

Feed Pump SCV (Suction Control Valve)

Delivery Valve

Fuel Tank

TWV

In-line, VE Pump

Engine ECU, Injector (TWV)*1

Engine ECU, Injector (TWV)*1

Engine ECU, Supply Pump

Engine ECU, Rail

Engine ECU, Supply Pump (SCV)*2

-3-

Page 6: izuzu_4hk1

2-2. Outline of SystemA. Composition

The common rail system consists primarily of a supply pump, rail, injectors, and engine ECU.

a. 4HK1

b. 6HK1

Q000737E

Fuel temperature sensor

Vehicle speedAccelerator opening

Intake air pressureIntake air temperature

Coolant temperature

Crankshaft positionCylinder recognition sensor

Engine ECU

Rail

Intake airflow rate

Rail pressuresensor

Supply pump

Fuel temperaturesensor SCV (suction

control valve)

Pressure limiter

Fuel tank

Injector

Q000523E

Fuel temperature sensor

Vehicle speedAccelerator opening

Intake air pressureIntake air temperature

Coolant temperature

Crankshaft positionCylinder recognition sensor

Engine ECU

Rail

Intake airflow rate

Rail pressuresensor

Supply pump

Fuel temperaturesensor SCV (suction

control valve)

Pressure limiter

Fuel tank

Injector

-4-

Page 7: izuzu_4hk1

B. Operationa. Supply pump (HP3/HP4)

The supply pump draws fuel from the fuel tank, and pumps the high pressure fuel to the rail. The quantity of fuel dis-

charged from the supply pump controls the pressure in the rail. The SCV (Suction Control Valve) in the supply pump

effects this control in accordance with the command received from the ECU.

b. Rail

The rail is mounted between the supply pump and the injector, and stores the high pressure fuel.

c. Injector (G2 type)

• This injector replaces the conventional injection nozzle, and achieves optimal injection by effecting control in accordance

with signals from the ECU. Signals from the ECU determine the length of time and the timing in which current is applied

to the injector.

• This in turn, determines the quantity, rate and timing of the fuel that is injected from the injector.

d. Engine ECU

The engine ECU calculates data received from the sensors to comprehensively control the injection quantity, timing and

pressure, as well as the EGR (exhaust gas recirculation).

2-3. Fuel System and Control SystemA. Fuel System

This system comprises the route through which diesel fuel flows from the fuel tank to the supply pump, via the rail, and

is injected through the injector, as well as the route through which the fuel returns to the tank via the overflow pipe.

B. Control SystemIn this system, the engine ECU controls the fuel injection system in accordance with the signals received from various

sensors. The components of this system can be broadly divided into the following three types: (a.) Sensors; (b.) Engine

ECU; and (c.) Actuators.

a. Sensors

Detect the engine and driving conditions, and convert them into electrical signals.

b. Engine ECU

Performs calculations based on the electrical signals received from the sensors, and sends them to the actuators in order

to achieve optimal conditions.

c. Actuators

Operate in accordance with electrical signals received from the ECU. Injection system control is undertaken by electron-

ically controlling the actuators. The injection quantity and timing are determined by controlling the length of time and the

timing in which the current is applied to the TWV (Two-Way Valve) in the injector. The injection pressure is determined

by controlling the SCV (Suction Control Valve) in the supply pump.

Crankshaft Position Sensor NE

Accelerator Position Sensor

Engine Speed

Cylider Recognition Sensor G

Cylinder Recognition

Load

Injector

Supply Pump (SCV)

•Injection Quantity Control•Injection Timing Control

•Injection Pressure Control

Other Sensors and Switches

EGR, Engine Warning Light

Sensor Actuator

Q000524E

EngineECU

Rail Pressure Sensor (*1)

(*1 : DENSO products)

EGR is produced by other manufactures.

-5-

Page 8: izuzu_4hk1

3. Construction and Operation3-1. Description of Main ComponentsA. Supply Pump (HP3, HP4)a. Outline

The supply pump consists primarily of the pump body (cam shaft, ring cam, and plungers), SCV (Suction Control Valve),

fuel temperature sensor, and feed pump.

• The two plungers for HP3 or the three plungers for HP4 are positioned vertically on the outer ring cam for compactness.

• The engine drives the supply pump at a ratio of 1:1. The supply pump has a built-in feed pump (trochoid type), and draws

the fuel from the fuel tank, sending it to the plunger chamber.

SCV

Fuel Temperature Sensor

Q000525E

HP3

SCV

Fuel Temperature Sensor

Q000526E

HP4

-6-

Page 9: izuzu_4hk1

• The internal camshaft drives the two plungers, and they pressurize the fuel sent to the plunger chamber and send it to

the rail. The quantity of fuel supplied to the rail is controlled by the SCV, using signals from the engine ECU. The SCV is

a normally opened type (the intake valve opens during de-energization).

QD0704E

Injector Rail Discharge ValveIntake Valve

Plunger

Return Spring

Intake PressureFeed Pressure

High Pressure

Return Pressure

Regulating Valve

Feed Pump

Fuel Inlet

Intake

Fuel Filter (with Priming Pump)

Camshaft

Filter

Return

Fuel Overflow

Fuel Tank

SCV

-7-

Page 10: izuzu_4hk1

• Development: HP3

Q000527E

Feed Pump

Fuel TemperatureSensor

Drive Shaft

Ring Cam

RegulatingValve

SCV

Pump Body

Plunger

Plunger

Filter

-8-

Page 11: izuzu_4hk1

• Development: HP4

Q000528E

Feed Pump

Fuel TemperatureSensor

Drive Shaft

Ring Cam

RegulatingValve

SCV

Pump Body

Plunger

Plunger

Filter

-9-

Page 12: izuzu_4hk1

b. Supply Pump Internal Fuel Flow

The fuel that is drawn from the fuel tank passes through the route in the supply pump as illustrated, and is fed into the rail.

c. Construction of Supply Pump (in case of HP3 pump)

• The eccentric cam is attached to the cam shaft. The eccentric cam is connected to the ring cam.

• As the cam shaft rotates, the eccentric cam rotates eccentrically, and the ring cam moves up and down while rotating.

Supply Pump Interior

Regulating Valve

Feed Pump

Overflow

Fuel Tank

SCV (Suction Control Valve)

Intake Valve

Pumping Portion (Plunger) Rail

Q000283E

QD0706E

Cam Shaft

Eccentric Cam Ring Cam

QD0727E

Ring Cam

Eccentric Cam

Cam Shaft

Plunger

-10-

Page 13: izuzu_4hk1

• The plunger and the suction valve are attached to the ring cam. The feed pump is connected to the rear of the cam shaft.

QD0728E

Plunger A

Ring Cam

Feed Pump

Plunger B

-11-

Page 14: izuzu_4hk1

d. Operation of the Supply Pump

• As shown in the illustration below (in case of HP3 pump), the rotation of the eccentric cam causes the ring cam to push

Plunger A upwards. Due to the spring force, Plunger B is pulled in the opposite direction to Plunger A.

• As a result, Plunger B draws in fuel, while Plunger A pumps it to the rail. In the case of the 4-cylinder engine used with

the HP3 pump, each plunger pumps fuel in a reciprocal movement during the 360° cam rotation.

• Conversely, in the case of the 6-cylinder engine used with the HP4 pump, 3 plungers pump fuel in a reciprocal movement

for each one rotation of the cam.

< NOTE >• There are 3 plungers for the HP4.

SCV

Plunger B

Plunger AEccentric Cam

Delivery ValveSuction Valve

Ring Cam

Plunger A: Complete Compression

Plunger B: Complete Intake

Plunger A: Complete Intake

Plunger B: Complete Compression

Plunger B: Begin Compression

Plunger A: Begin Intake

Plunger B: Begin Intake

Plunger A: Begin Compression

QD0707E

-12-

Page 15: izuzu_4hk1

B. Description of Supply Pump Componentsa. Feed Pump

• The trochoid type feed pump, which is integrated in the supply pump, draws fuel from the fuel tank and feeds it to the

two plungers via the fuel filter and the SCV (Suction Control Valve).

• The feed pump is driven by the drive shaft. With the rotation of the inner rotor, the feed pump draws fuel from its suction

port and pumps it out through the discharge port.

• This is done in accordance with the space that increases and decreases with the movement of the outer and inner rotors.

b. SCV: Suction Control Valve (Normally open type)

• A linear solenoid type valve has been adopted. The ECU controls the duty ratio (the duration in which current is applied

to the SCV), in order to control the quantity of fuel that is supplied to the high-pressure plunger.

• Because only the quantity of fuel that is required for achieving the target rail pressure is drawn in, the actuating load of

the supply pump decreases.

• When current flows to the SCV, variable electromotive force is created in accordance with the duty ratio, moving the ar-

mature to the left side. The armature moves the cylinder to the left side, changing the opening of the fuel passage and

thus regulating the fuel quantity.

• With the SCV OFF, the return spring contracts, completely opening the fuel passage and supplying fuel to the plungers.

(Full quantity intake and full quantity discharge)

• When the SCV is ON, the force of the return spring moves the cylinder to the right, closing the fuel passage (normally

opened).

• By turning the SCV ON/OFF, fuel is supplied in an amount corresponding to the actuation duty ratio, and fuel is dis-

charged by the plungers.

(1) In case of short time ON duty

QD0708E

Inner Rotor

Intake Port

Outer Rotor to Pump Chamber

from Fuel Tank

Discharge Port

Quantity Decrease

Quantity Increase

Quantity Decrease (Fuel Discharge)

Quantity Increase (Fuel Intake)

Q000270E

Exterior View of SCV Cross-section of SCV

Pump Body

SCV

Cylinder

Return Spring

-13-

Page 16: izuzu_4hk1

Short time ON duty => large valve opening => maximum intake quantity

Feed Pump

SCV

Large OpeningCylinder

Cylinder

Plunger

Q000051E

-14-

Page 17: izuzu_4hk1

(2) In case of long time ON duty

Long time ON duty => small valve opening => minimum intake quantity

Feed Pump

SCV

Small Opening Cylinder

Q000052E

Cylinder

Plunger

-15-

Page 18: izuzu_4hk1

C. Raila. Outline

• Stores pressurized fuel (0 to 160 MPa {0 to 1631.6 kg/cm2}) that has been delivered from the supply pump and distributes

the fuel to each cylinder injector. A rail pressure sensor and a pressure limiter are adopted in the rail.

• The rail pressure sensor (Pc sensor) detects the fuel pressure in the rail and sends a signal to the engine ECU, the pres-

sure limiter prevents the rail pressure from being abnormally high. This ensures optimum combustion and reduces com-

bustion noise.

Q000529E

Pressure Sensor

Pressure Limiter

For 4HK1

Q000530E

Pressure Sensor

Pressure Limiter

For 6HK1

-16-

Page 19: izuzu_4hk1

b. Pressure Limiter

• The pressure limiter opens to release the pressure if an abnormally high pressure is generated.

• When the rail pressure reaches approximately 200 MPa (2038 kg/cm2), it trips the pressure limiter (the valve opens).

When the pressure drops to approximately 50 MPa (509.5 kg/cm2), the pressure limiter returns to its normal state (the

valve closes) in order to maintain the proper pressure.

c. Pressure Sensor

• The rail pressure sensor (Pc sensor) is attached to the rail in order to detect the fuel pressure.

• It is a semiconductor type pressure sensor that utilizes the characteristics of silicon, whereby the electrical resistance

changes when pressure is applied to it.

< NOTE >• It is necessary to reset the ECU default value using the ISUZU diagnosis tool at the time of supply pump service replace-

ment. In addition, the ECU has a function enabling it to learn the performance of the supply pump at the time of ECU

service replacement, so ensure sufficient time (several minutes) is available.

Q000531E

Valve Open

Valve Close50 MPa (509.5 kg/cm2)

: 4HK1 200 ± 9 MPa (2038 ± 92 kg/cm2)

: 6HK1 221 ± 9 MPa (2254 ± 92 kg/cm2)

Q000532E

VC VOUT GND

4.2 V

1.0 V

0 200 MPa (2038 kg/cm2)

-17-

Page 20: izuzu_4hk1

d. Flow Damper

• The flow dampers are installed at the outlet of rail to damp a pulsation of fuel pressure inside the rail or to cut off the fuel

supply when the fuel leaks in the downstream of flow damper. The fuel is supplied to the injectors through an orifice of

the piston. The pressure pulsation occurring in the rail is damped by a resistive force of the return spring (5) and a passing

resistance of the orifice (2), wherein the piston (4) acts as a damper. (Refer to the picture B)

• Also, the leading end of piston (4) closes an fuel supply port to cut off the fuel supply, if the fuel leak occurs in the injection

pipe or injectors, and the fuel pressure on the downstream side of flow damper supplied through an orifice (2) + resistive

force of return spring (5) do not balance with the fuel pressure applied on the piston (4) surface prior to the orifice (2).

(Refer to the picture C)

• The piston (4) will return when the fuel pressure inside the rail less than 1.0 MPa (10.2 kgf/cm2).

(1) From Rail (7) To Injector

(2) Orifice (3) Slit

(4) Piston

(5) Return Spring

(6) Housing

A B C

Q000742E

-18-

Page 21: izuzu_4hk1

D. Injector (G2 Type)a. Outline

The injectors inject the high-pressure fuel from the rail into the combustion chambers at the optimum injection timing,

rate, and spray condition, in accordance with commands received from the ECU.

b. Characteristics

• A compact, energy-saving solenoid-control type TWV (Two-Way Valve) injector has been adopted.

• QR codes displaying various injector characteristics and the ID codes showing these in numeric form (30 base 16 char-

acters) are engraved on the injector head. The 4HK1/6HK1 engine common rail system optimizes injection volume con-

trol using this information. When an injector is newly installed in a vehicle, it is necessary to enter the ID codes in the

engine ECU using the ISUZU Diagnostic tool.

c. Construction

Q000533E

Pressurized Fuel (from Rail)

Command Piston

QR Codes

30 base 16 characters

Nozzle Spring

Pressure Pin

Nozzle Needle

Solenoid Valve

Control Chamber

-19-

Page 22: izuzu_4hk1

d. QR Codes

• In order to minimize performance tolerance of injectors at replacing them, QR*1 (Quick Response) codes have been

adopted to enhance correction precision.

• Using QR codes has resulted in a substantial increase in the number of fuel injection quantity correction points, and thus

the injection quantity control precision has improved. The characteristics of the engine cylinders have been further uni-

fied, contributing to improvements in combustion efficiency, reductions in exhaust gas emissions and so on.

< NOTE >• QR code correction points

• Location of QR codes

e. Repair Procedure Changes

• Differences in comparison with the conventional method of replacing injectors assembly are as shown below.

< NOTE >• When replacing injectors with QR codes, or the engine ECU, it is necessary to record the ID codes (QR codes) in the

ECU. (If the ID codes of the installed injector are not registered correctly, engine failure such as rough idling and noise

will result.)

• New (Injector with QR Codes)

Injection quantity Q

Actuating pulse width TQ

Pressure Parameter

QR code on the injector connector

Q000670E

Q000534E

QR Codes ( 9.9mm)

ID Codes(30 alphanumeric figures)Base 16 characters noting fuel injection quantity correction information for market service use.

Q000535E

30 base 16 characters noting fuel injection quantity correction information displaed for market service use

ID Code

-20-

Page 23: izuzu_4hk1

• Replacing the Injector

• Replacing the Engine ECU

E. Engine ECU (Electronic Control Unit)a. Outline

This is the command center that controls the fuel injection system and engine operation in general.

Engine ECU

Spare Injector

"No correction resistance, so no electrical recognition capability"

QD1536E

* Necessary to record the injector ID codes in Engine ECU

Vehicle-side Injector

"No correction resistance, so no electrical recognition capability"

QD1537E

Spare Engine ECU

* Necessary to record the injector ID codes in the engine ECU

Outline Diagram

Sensor Engine ECU Actuator

Detection Calculation Actuation

QD2352E

-21-

Page 24: izuzu_4hk1

3-2. Description of Control System ComponentsA. Engine Control System Diagram

a. Fuel Temperature Sensor (THL)

• The fuel temperature sensor detects the fuel temperature and outputs it to the ECU. The sensor uses a thermistor, which

varies resistance according to temperature.

• As the ECU applies voltage to the thermistor, it uses a voltage resulting from the division of the computer internal resis-

tance and the thermistor resistance to detect the temperature.

EGRValve

Q000536E

Intake Air Temperature Sensor

Mass Airflow Meter

VNTController

VNT Actuator

Inter-Cooler

Intake Air Pressure Sensor

G2 Injector

EGR Cooler

Coolant

Oxidation Catalyst

VTHL

ECU

A-GND

+5V

THL

VTHL

Fuel TemperatureQ000106E

Output Voltage

-40 -4 32 68 104 140 176 212 248 (°F)

5

4

3

2

1

0-40 -20 0 20 40 60 80 100 120 (°C)

(V)

-22-

Page 25: izuzu_4hk1

b. Atmospheric Air Pressure Sensor (Built-in ECU)

This sensor converts the atmospheric air pressure into an electrical signal to correct full load injection volume.

Atmospheric Air Pressure (kPa {kg/cm2})

Output Voltage (V)

VPATM

3.8

107 {1.09}

Q000278E

-23-

Page 26: izuzu_4hk1

3-3. Various Types of Control• This system controls the fuel injection quantity and injection timing more optimally than the mechanical governor or timer

used in conventional injection pumps.

• For system control, the ECU makes the necessary calculations based on signals received from sensors located in the

engine and on the vehicle in order to control the timing and duration in which current is applied to the injectors, thus re-

alizing optimal injection timing.

A. Fuel Injection Rate Control FunctionThe fuel injection rate control function controls the ratio of the quantity of fuel that is injected through the nozzle hole

during a specified period.

B. Fuel Injection Quantity Control FunctionThe fuel injection quantity control function, replaces the conventional governor function, and controls fuel injection to

achieve an optimal injection quantity based on the engine speed and the accelerator opening.

C. Fuel Injection Timing Control FunctionThe fuel injection timing control function, replaces the conventional timer function, and controls the fuel injection to

achieve an optimal injection timing according to the engine speed and the injection quantity.

D. Fuel Injection Pressure Control Function (Rail Pressure Control Function)• The fuel injection pressure control function (rail pressure control function) uses a rail pressure sensor to measure fuel

pressure, and feeds this data to the ECU to control the pump discharge quantity.

• Pressure feedback control is implemented to match the optimal quantity (command quantity) set according to the engine

speed and the fuel injection quantity.

Input Signal Control Output

Accelerator sensor

Rail Pressure Sensor (*1)

NE Sensor

(Crankshaft Position Sensor)

TDC Sensor

(Cylinder Recognition Sensor)

Various Sensors (*1)

·Water Temperature Sensor

·Fuel Temperature Sensor

·Atmospheric Air Temperature

Sensor etc.

Fuel Control Computer

(ECU)

Fuel Injection Rate Control

Fuel Injection Quantity Control

Fuel Injection Timing Control

Fuel Injection Pressure Control

Diagnosis

Atmospheric Air Pressure Sensor

Q000537E

(*1 : DENSO products)

-24-

Page 27: izuzu_4hk1

E. Fuel Injection Rate Controla. Main Injection

Same as conventional fuel injection.

b. Pilot Injection

• Pilot injection is the injection of a small amount of fuel prior to the main injection.

• While the adoption of higher pressure fuel injection is associated with an increase in the injection rate, the lag (injection

lag) that occurs from the time fuel is injected until combustion starts cannot be reduced below a certain value. As a result,

the quantity of fuel injected before ignition increases, resulting in explosive combustion together with ignition, and an in-

crease in the amount of NOx and noise. Therefore, by providing a pilot injection, the initial injection rate is kept to the

minimum required level dampening, the explosive first-period combustion and reducing NOx emissions.

Q000110E

Pilot Injection

Main Injection

Q000111E

CombustionProcess

Injection Rate

Heat GenerationRate

TDC

High InjectionRate

Large Pre-mixtureCombustion(NOx, Noise)

Ignition Delay

Small Injection AmountPrior to Ignition

Pilot Injection

Small Pre-mixtureCombustion

Improvement

-25-

Page 28: izuzu_4hk1

F. Fuel Injection Quantity Controla. Starting Injection Quantity

The injection quantity is determined based on the engine speed (NE) and water temperature while starting.

b. Transient Injection Quantity Correction

When the changes in the accelerator opening are great during acceleration, the increase in fuel volume is delayed to

inhibit the discharge of black smoke.

c. Basic Injection Quantity

• This quantity is determined in accordance with the engine speed (NE) and the accelerator opening.

• Increasing the accelerator opening while the engine speed remains constant causes the injection quantity to increase.

Q000127E

Water Temperature

Starting Injection Quantity

Engine Speed

Q000128E

Injection Quantity

Time

Change in Accelerator Opening

Injection Quantity after Correction

Delay Time

Q000129E

Basic Injection Quantity

Engine Speed

Accelerator Opening

-26-

Page 29: izuzu_4hk1

d. Injection Quantity for Maximum Speed Setting

The injection quantity is regulated by a value that is determined in accordance with the engine speed.

e. Maximum Injection Quantity

Is determined in accordance with the engine speed and corrected by the coolant temperature signal.

f. Amount of Injection Quantity Intake Pressure Correction

Limits the maximum injection quantity in accordance with the intake pressure, in order to minimize the discharge of

smoke when the intake air pressure is low.

Q000130E

Injection Quantity for Maximum Speed Setting

Engine Speed

Q000131E

Basic Maximum Injection Quantity

Engine Speed

Q000133EEngine Speed

Amount of Intake Air Pressure Correction

-27-

Page 30: izuzu_4hk1

g. Amount of Injection Quantity by Atmospheric Air Pressure Correction

With using atmospheric air pressure sensor signal, the maximum injection quantity curve is corrected as shown in the

figure below.

h. Idle Speed Control System (ISC)

Controls the idle speed by regulating the injection quantity in order to match the target speed, which has been calculated

by the computer, with the actual speed. The functions of the ISC can be broadly divided into the following two items:

(1) Auto ISC

Controls the idle speed in accordance with the water temperature.

(2) Manual ISC

Controls the idle speed in accordance with the idle speed indicated on the manual idle setting knob provided at the driv-

er's seat.

Q000134EEngine Speed

Amount of Atmospheric Air Pressure Correction

Q000135E

Target Speed

Water Temperature

Q000136E

Target Speed

ISC Knob Terminal Voltage

-28-

Page 31: izuzu_4hk1

(3) Air Conditioner Idle-up Control

When the conditions shown in the chart on the right are realized, bring the idle-up speed to constant rpm.

i. Auto Cruise Control

• Controls the actual vehicle speed by regulating the injection quantity in order to match the target speed that has been

calculated by the computer with the actual speed.

• The CRS ECU controls the injection quantity in accordance with signals from the cruise control computer.

Q000137E

Air Conditioning SW = "ON"

Conditions

Clutch SW = "ON" (Clutch Connection)

Neutral SW = "ON" (Neutral)

-29-

Page 32: izuzu_4hk1

G. Fuel Injection Timing ControlThe characteristics of the fuel injection timing vary depending on whether it is the main injection or the pilot injection.

Although either the NE sensor or the auxiliary NE sensor is the reference for controlling the injection timing, the NE sen-

sor is ordinarily used for this purpose.

a. Main Injection Timing

• The basic injection timing is calculated in accordance with the final injection quantity, the engine speed, and the water

temperature (with map correction).

• While starting, it is calculated in accordance with the water temperature and the engine speed.

b. Pilot Injection timing (Pilot Interval)

• The pilot injection timing is controlled by adding the pilot interval to the main injection timing.

• The pilot interval is calculated in accordance with the final injection quantity, the engine speed, and the water temperature

(with map correction).

• While starting, it is calculated in accordance with the water temperature and the engine speed.

c. Fuel Injection Pressure

• A value is calculated as determined in accordance with the final injection quantity and the engine speed.

• While starting, it is calculated in accordance with the water temperature and the engine speed.

Q000138E

Basic Injection Timing

Final Injection Quantity

Engine Speed

Q000139E

Final Injection Quantity

Engine Speed

Pilot Interval

Q000140E

Final Injection Quantity

Engine Speed

Rail Pressure

-30-

Page 33: izuzu_4hk1

3-4. Engine ECUA. Diagnosis Codesa. 4HK1

DTC Code Code Description

P0643 Analog Sensor Reference Voltage Output No.1 Too High

P0642 Analog Sensor Reference Voltage Output No.1 Too Low

P0653 Analog Sensor Reference Voltage Output No.2 Too High

P0652 Analog Sensor Reference Voltage Output No.2 Too Low

P0699 Analog Sensor Reference Voltage Output No.3 Too High

P0698 Analog Sensor Reference Voltage Output No.3 Too Low

P0118 Coolant Temp. Sensor Signal Too High

P0117 Coolant Temp. Sensor Signal Too Low

P0113 Intake Air Temp. Sensor Signal Too High

P0112 Intake Air Temp. Sensor Signal Too Low

P0183 Fuel Leak Temp. Sensor Signal Too High

P0182 Fuel Leak Temp. Sensor Signal Too Low

P0113 ATM Temp. Sensor Signal Too High

P0112 ATM Temp. Sensor Signal Too Low

P0193 C/Rail Press. Sensor Signal Too High

P0192 C/Rail Press. Sensor Signal Too Low

P2229 Atom Press. Sensor Signal Too High

P2228 Atom Press. Sensor Signal Too Low

P0238 Boost Pressure Sensor Signal Too High

P0237 Boost Pressure Sensor Signal Too Low

P0563 Ignition1 Voltage Too High

P0562 Ignition1 Voltage Too Low

P0103 MAF Sensor Signal Too High

P0102 MAF Sensor Signal Too Low

P1597 PTO Accelerator Sensor Signal Too High

P1594 Idleup Signal Too High

P1593 Idleup Signal Too Low

P0406 EGR Position Signal Too High

P0405 EGR Position Signal Too Low

P0571 Cruise / Brake Switch Circuit Malfunction

P0567 Cruise Resume / Accelerator Signal

P0568 Cruise Set / Coast Signal Malfunction

P0335 Crank Sensor No Pulse

P0340 Cam Sensor No Pulse

P0092 SCV (+) output short to BATT

SCV (-) output short to BATT

-31-

Page 34: izuzu_4hk1

P0091 SCV (+) output open Load / short to GND

SCV (-) output open Load / short to GND

SCV coil open

P1264 COM1 output short to BATT;

TWV1 or 3 (or 5) output short to BATT

P1263 COM1 output short to GND;

TWV1 or 3 (or 5) output short to GND

P2152 COM1 output open load;

Both TWV1 or 3 (or 5) output open load

P1266 COM2 output short to BATT;

TWV2 or 4 (or 6) output short to BATT

P1265 COM2 output short to GND;

TWV2 or 4 (or 6) output short to GND

P2155 COM2 output open load;

Both TWV2 or 4 (or 6) output open load

P0201 TWV1 output open load

Injector#1 coil open

P0202 TWV2 output open load

Injector#3 coil open

P0203 TWV3 output open load

Injector#4 coil open

P0204 TWV4 output open load

Injector#2 coil open

P1261 Capacitor charge-up circuit malfunction (insufficient charge)

P1261 Capacitor charge-up circuit malfunction (excessive charge)

P0088 Common rail pressure exceeds upper

P0088 Common rail pressure exceeds hi upper limit

P0382 Glow Controller Command Line Short to BATT

P0382 Glow Controller Command Line Open Load / Short to GND

P1094 C/Rail Press. Sensor Performance Invalid included fuel leak

P0087 P/L (pressure limiter) activated

P1404 EGR Position Error

P0400 EGR Duty Error

P0500 Vehicle Speed Sensor Malfunction

P0606 CPU fault;

-Main CPU fault

P0606 CPU fault;

-Watchdog IC fault

P0602 EEPROM/EERPOM Emulation via Flash EPROM Write Error

P0219 Engine overrun

P0512 Starter Switch Short to BATT

DTC Code Code Description

-32-

Page 35: izuzu_4hk1

P0686 Main relay diagnostics;

Main relay stuck closed

P0089 Supply pump control valve (suction control valve) stuck

P0299 Boost Pressure Sensor exceeds lower limit

P0234 Boost Pressure Sensor exceeds upper limit

P2293 Supply pump protection

P2294 Supply pump exchange

P1093 Supply pump malfunction

P2122 Accelerator Pedal Position Sensor 1 Low Voltage

P2123 Accelerator Pedal Position Sensor 1 High Voltage

P2127 Accelerator Pedal Position Sensor 2 Low Voltage

P2128 Accelerator Pedal Position Sensor 2 High Voltage

P2132 Accelerator Pedal Position Sensor 3 Low Voltage

P2133 Accelerator Pedal Position Sensor 3 High Voltage

P1125 Pedal Position Sensor Circuit Intermittent

P2138 Accelerator Pedal Position Sensor 1, 2 Correlation Error

P2140 Accelerator Pedal Position Sensor 2, 3 Correlation Error

P2139 Accelerator Pedal Position Sensor 1, 3 Correlation Error

U2104 CAN Bus Error

U2106 CAN TCM SOH Diagnostic

P0602 QR Code Not Programmed

P0602 QR Code ERROR

DTC Code Code Description

-33-

Page 36: izuzu_4hk1

b. 6HK1

DTC Code Code Description

P0641 Analog Sensor Reference Voltage Output No.1 Too High

P0641 Analog Sensor Reference Voltage Output No.1 Too Low

P0651 Analog Sensor Reference Voltage Output No.2 Too High

P0651 Analog Sensor Reference Voltage Output No.2 Too Low

P1646 Analog Sensor Reference Voltage Output No.3 Too High

P1646 Analog Sensor Reference Voltage Output No.3 Too Low

P0118 Coolant Temp. Sensor Signal Too High

P0117 Coolant Temp. Sensor Signal Too Low

P0113 Intake Air Temp. Sensor Signal Too High

P0112 Intake Air Temp. Sensor Signal Too Low

P0183 Fuel Leak Temp. Sensor Signal Too High

P0182 Fuel Leak Temp. Sensor Signal Too Low

P0523 Oil Press. Sensor Signal Too High

P0522 Oil Press. Sensor Signal Too Low

P0463 Fuel Level Sensor1 Signal Too High

P0462 Fuel Level Sensor1 Signal Too Low

P1433 Fuel Level Sensor2 Signal Too High

P1432 Fuel Level Sensor2 Signal Too Low

P0193 C/Rail Press. Sensor Signal Too High

P0192 C/Rail Press. Sensor Signal Too Low

P0190 C/Rail Press. Sensor Signal keeping the middle range

P0108 Atom Press. Sensor Signal Too High

P0107 Atom Press. Sensor Signal Too Low

P0238 Boost Pressure Sensor Signal Too High

P0237 Boost Pressure Sensor Signal Too Low

P0563 Ignition1 Voltage Too High

P0562 Ignition1 Voltage Too Low

P2003 MAF Sensor Signal Too High

P2004 MAF Sensor Signal Too Low

P2005 PTO Accelerator Sensor Signal Too High

P2007 VNT Current Too High

P2008 VNT Current Too Low

P0704 Clutch Pedal Switch Circuit

P0571 Cruise / Brake Switch Circuit Malfunction

P0571 Cruise / Brake Switch Circuit Malfunction

P0567 Cruise Resume / Accelerator Signal

P0568 Cruise Set / Coast Signal Malfunction

P0335 Crank Sensor No Pulse

P0385 Cam Sensor No Pulse

-34-

Page 37: izuzu_4hk1

P0092 SCV (+) output short to BATT

SCV (-) output short to BATT

P0091 SCV (+) output open Load / short to GND

SCV (-) output open Load / short to GND

SCV coil open

P1264 COM1 output short to BATT;

TWV1 or 3 (or 5) output short to BATT

P1263 COM1 output short to GND;

TWV1 or 3 (or 5) output short to GND

P2011 COM1 output open load;

Both TWV1 or 3 (or 5) output open load

P1266 COM2 output short to BATT;

TWV2 or 4 (or 6) output short to BATT

P1265 COM2 output short to GND;

TWV2 or 4 (or 6) output short to GND

P2012 COM2 output open load;

Both TWV2 or 4 (or 6) output open load

P0201 TWV1 output open load

Injector#1 coil open

P0202 TWV2 output open load

Injector#5 coil open

P0203 TWV3 output open load

Injector#3 coil open

P0204 TWV4 output open load

Injector#6 coil open

P0205 TWV5 output open load

Injector#2 coil open

P0206 TWV6 output open load

Injector#4 coil open

P1261 Capacitor charge-up circuit malfunction (insufficient charge)

P1261 Capacitor charge-up circuit malfunction (excessive charge)

P1088 Common rail pressure exceeds hi upper limit

P0382 Glow Controller Command Line Short to BATT

P0382 Glow Controller Command Line Open Load / Short to GND

P0500 Vehicle Speed Sensor Malfunction

P0087 C/Rail Press. Sensor Performance Invalid included fuel leak

P1087 P/L (pressure limiter) activated

P2565 VNT Position Signal Too high

P2564 VNT Position Signal Too low

P2900 VNT Position Stick

P2901 EGR Brushless motor Position Sensor Signal Invalid

P2902 EGR Brushless motor Performance Error

DTC Code Code Description

-35-

Page 38: izuzu_4hk1

P2903 EGR Valve open/Close Stick

P0606 CPU fault;

-Main CPU fault

P0606 CPU fault;

-Watchdog IC fault

P1621 EEPROM/EERPOM Emulation via Flash EPROM Write Error

P0219 Engine overrun

P0512 Starter Switch Short to BATT

P2920 Main relay diagnostics;

Main relay stuck closed

P0088 Supply pump control valve (suction control valve) stuck

P0234 Boost Pressure Sensor exceeds upper limit

P0234 Boost Pressure Sensor exceeds upper limit (Long time)

P2921 Supply pump protection

P2922 Supply pump exchange

P2923 Supply pump malfunction

P1277 Accelerator Pedal Position Sensor 1 Low Voltage

P1278 Accelerator Pedal Position Sensor 1 High Voltage

P1282 Accelerator Pedal Position Sensor 2 Low Voltage

P1283 Accelerator Pedal Position Sensor 2 High Voltage

P1287 Accelerator Pedal Position Sensor 3 Low Voltage

P1288 Accelerator Pedal Position Sensor 3 High Voltage

P1125 Pedal Position Sensor Circuit Intermittent

P1271 Accelerator Pedal Position Sensor 1, 2 Correlation Error

P1272 Accelerator Pedal Position Sensor 2, 3 Correlation Error

P1273 Accelerator Pedal Position Sensor 1, 3 Correlation Error

U1300 Class2 Bus Short to Ground

U1301 Class2 Bus Short to Battery

U2104 CAN Bus Error

P0461 Fuel Level Sensor Circuit Performance

P0602 QR Code Not Programmed

P0602 QR Code ERROR

DTC Code Code Description

-36-

Page 39: izuzu_4hk1

B. ECU External Wiring Diagrama. 4HK1 Diagram (1)

Q000538E

BATTERY

ON

ACC

LOCK

START

MAIN-RELAY

GLOW-RELAY

TAP DOWN

PTO SW

PTO ENABLE RELAY OPTION

TAP UP

IG1-SW

M-REL

M-REL

+B

+B

+B

GL-CONT

(GM1-FB)

(GM2-FB)

(GM3-FB)

(GM4-FB)

BATT

BK1-SW

BK2-SW

CRM-SW

CRR-SW

CRS-SW

PTOEN-SW

PTOEN-REL

PTOFB-SW

PTODIS-SW

SHUTDOWN-SW

RSET-SW

RRES-SW

SSPA-SW

SSPB-SW

CCDIS-SW

IGBC-SW

CL-SW

FUEL-SW *1

(TQLIM-SW)

(TQCUT-SW)

(SP1-GND)

(SP2-GND)

PACL-GND

PACL-VCC

IDLUP-GND

IDLUP-VCC

G-VB

STA-SW

STARTER RELAY

STARTER CUT RELAY

SCV

CRANK POSITION SENSOR

SPEED SENSOR

BOOST PRESSURE SENSOR

RAIL PRESSURE SENSOR

PTO ACCEL SENSOR

IDLE UP VOLUME

CAM ANGLE SENSOR (HALL)

METER

APS1

APS2

APS3

AT

STAEN-REL

SCVHI

SCVHI

SCVLO

SCVLO

NE+

NE-

NE-SLD

SPD

ECU

G

G-SLD

PB-VCC

PBOOST

PB-GND

PFUEL-VCC

PFUEL-GND

APS1-VCC

APS2-VCC

APS3-VCC

APS3

APS1-GND

APS2-GND

APS3-GND

APS1

APS2

PFUEL

PFUEL

IDLUP

PACL

(SP1-VCC)

(SP1)

(SP2)

A

A

A

A

A

B

C

C

KEY SW

+

-

-37-

Page 40: izuzu_4hk1

b. 4HK1 Diagram (2)

Q000539E

(FQ1)

COOLANT TEMP

FUEL TEMP

MAF

CYL1

CYL4

CYL3

CYL2

EXHAUST BRAKE CUT RELAY

EXHAUST BRAKE RELAY (CHARGE)

EXHAUSTBRAKE RELAY

ABS

INTAKE AIR TEMP

DIAG CLEAR-SW

REF-SW

AC-SW

METER

METERABS

AT

AT

TOOL

TOOL

EGR DC BRUSH MOTOR

EGR POSITION SENSOR

M+

M-

TWISTED PAIR

AT CONTROLLER

(FQ2)

(FQ3)

(INCA-BAT)

(INCA-GND)

THWOUT

TACHO

CAN1H

CAN1L

(CAN1-SLD)

AT-TACHO

CRSET-L

MIL

CRM-L

GL-L

(EXB-L)

CLASS2

CLASS2

KWP2000

EBM1

EBM2

EGR-VCC

EGR-GND

EGP-POS

(EBM-W)

(EGR-UPOS)

(EGR-VPOS)

(EGR-WPOS)

(IDM1)

(IDM2)

INT-VCC

INT-GND

INT

THW

(LOL-SW)

POIL-GND

(POIL-VCC)

(POIL)

THF1

(THF2)

(THO)

THA

MAF

MAF-GND

(SP3-GND)

(ATMT-GND)

(ATMT)

(ACGL-SW)

(ACG-F)

COMMON1

COMMON1

TWV-A

TWV-C

TWV-B

TWV-D

EXB-SW

EXB-REL

P-GND

P-GND

P-GND

P-GND

GND

GND

CASE-GND

AT

M

PR

ES

SU

RE

COMMON2

COMMON2

(SP3)

A

B

C

ECU

-38-

Page 41: izuzu_4hk1

c. 6HK1 Diagram (1)

A B

C

B

A

C

STA-SWSTARTER SW

BATT

IG0-SW

IG1-SW

GL-REL

(+B) *1

+B

+B

M-REL

M-REL

GL-L

FIDL-L

BK1-SW

BK2-SW

CRM-SW

CRR-SW

CRS-SW

PTOEN-SW

PTOEN-REL

PTOFB-SW

PTODIS-SW

RSET-SW

RRES-SW

RRPA-SW

RRPB-SW

CCDIS-SW

IGBC-SW

CL-SW

FAXLE-SW

SCVHI

SCVHI

SCVLO

SCVLO

NE+

NE-

NE-SLD

VSS+

VSS-

VSS-SLD

G-VB

G-SLD

PBOOST

PB-VCC

PB-GND

PFUEL

PFUEL

PFUEL-VCC

APS1-VCC

APS2-VCC

APS3-VCC

PACL-VCC

POIL-VCC

POIL-GND

THW

THD

THA

MAF

MAF-GND

THF1

*2 THF2

POIL

PACL-GND

PACL

APS1-GND

APS2-GND

APS3-GND

APS1

APS2

APS3

PFUEL-GND

G

ECUIGN A

GLOW RELAY

GLOWPLUG

ENGINE BLOCK

IGNITION3

TOP DOWN

PTO SW

PTO ENABLE RELAY

(UPFTR SUP) (UPFTR SUP)

TOP UP

POWER MAINTAIN RELAY

IGN B

APS1

APS2

APS3

PTO ACCEL SENSOR

ENGINE OIL PRESSURE SENSOR

COOLANT TEMP

FUEL TEMP#1

FUEL TEMP#2

ENGINE OIL TEMP

INTAKE AIR TEMP

MAF

TWISTED PAIR

SCV

CRANK POSITION SENSOR

CAM ANGLE SENSOR (HALL)

BOOST SENSOR PRESSURE

PRESSURE SENSOR COMMON RAIL

VEHICLE SPEED SENSOR

LCT TCM

Q000540E

*1: In case of connecting to outside wiring, note that this termonal is connected to +B inside ECU.*2: This terminal is unused.

-39-

Page 42: izuzu_4hk1

d. 6HK1 Diagram (2)

Q000541E

B

C

REV-SW

LOL-SW

FIDL-SW

AC-SW

4WD-SW

LCL-SW

AC HI-PRESS SWA/C REQUEST SW

WIF-SW

N-SW

LOW PRESSURE SWA/C RELAY

A/C CLUTCH

BATT

CLUSTER

TCM

CHASSIS BUILDER

TECH II

TWISTED PAIR

MANUAL

ELECTRIC 2SPD. AXLE SW AUTOMATC

AIR 2SPD. AXLE SENSOR

2SPD. AXLE MOTER

2SAXLE-SW

ACCL-REL

MIL

TACHO

VSOUT1

VSOUT2

CLASS2

CLASS2

DIAGCL-SW

CAN1H

CAN1L

CAN1-SLD

ATM PRESSURE

COM-GND

LFUEL1

LFUEL2

ACGL-SW

ACG-F

STAEN-REL

COMMON1

FUEL LEVEL#1

FUEL LEVEL#2

IGN (CRANK)

STARTER R/L

CLUTCH SW

CYL1

CYL2

CYL3

CYL4

CYL5

CYL6

ABS TCM

EGR VALVE DRIVE DC BRUSH-LESS MOTOER

LCT WTERC

W/ABSNO ABS

EXHT Telltail-TTM

EXHT BRK SOLENOID

VB

ACG

ACG

COMMON1

COMMON2

COMMON2

TWV-A

TWV-E

TWV-C

TWV-F

TWV-B

TWV-D

EXB-SW

EXB-REL

P-GND

P-GND

P-GND

P-GND

CASE-GND

EGR-VCC

EGR-GND

EGR-UPOS

EGR-VPOS

EGR-WPOS

EBM-U

EBM-V

EBM-W

AVNTAVNT

AVNT POSITION SENSOR

VNTPOS-VCC

VNTPOS-SIG

VNTPOS-GND

GND

GND

ECU

IGN3

IGN3

NOTE:

Un lock

Run

Crank

Lock/Accessory

IGN0

1

1

1

0

IGN1

0

1

1

0

CRANK

0

0

1

0

IGN3

0

1

0

0

-40-

Page 43: izuzu_4hk1

C. ECU Connector Diagrama. 4HK1 ECU Connector Terminal Layout

b. 4HK1 Terminal Connections

ECU CONNECTOR PIN ASSIGNMENT : 154PIN

Q000542E

No. Terminal Name Content No. Terminal Name Content

A-1 CASE-GND CASE GND A-31 APS1 ACCEL POSITION 1 SIG

A-2 P-GND POWER GND A-32 APS2 ACCEL POSITION 2 SIG

A-3 P-GND POWER GND A-33 APS3 ACCEL POSITION 3 SIG

A-4 GND ECU SENSOR GND A-34 PACL PTO ACCEL SIG

A-5 GND ECU SENSOR GND A-35 IDLUP IDLE UP SIG

A-6 N/A (Q CONTROL RESISTOR 3) A-36 N/A (SP1)

A-7 APS1-GND V5RTN1 A-37 N/A (SP2)

A-8 APS2-GND V5RTN2 A-38 N/A (ATM TEMP SIG)

A-9 APS3-GND V5RTN3 A-39 SPD SPEED INPUT

A-10 PACL-GND PTO ACCEL GND A-40 — —

A-11 IDLUP-GND IDLE UP GND A-41 N/A (ACG-F PULSE INPUT)

A-12 N/A (SP3 GND) A-42 — —

A-13 N/A (ATM TEMP GND) A-43 N/A (GLOW MONITOR2 FEEDBACK)

A-14 — — A-44 N/A (GLOW MONITOR3 FEEDBACK)

A-15 N/A (SP1-GND) A-45 AC-SW A/C CLUTCH REQUEST SW

A-16 CAN1-SLD CAN1 SHIELD GND A-46 CRM-SW RUISE ENABLE (ON/OFF) SW

A-17 CAN1H CAN1 HIGH A-47 CRR-SW CRUISE RESUME/ACCEL SW

A-18 CAN1L CAN1 LOW A-48 CRS-SW CRUISE SET/COAST SW

A-19 KWP2000 ISO14230 A-49 +B POWER

A-20 CLASS2 J1850 A-50 +B POWER

A-21 CLASS2 J1850 A-51 BATT BATTERY

A-22 — — A-52 M-REL POWER MAINTAIN RELAY

A-23 IG1-SW IGNITION 1 A-53 M-REL POWER MAINTAIN RELAY

A-24 THWOUT THW PWM OUTPUT A-54 APS1-VCC VBREF1

A-25 — — A-55 APS2-VCC VBREF2

A-26 P-GND POWER GND A-56 APS3-VCC VBREF3

A-27 P-GND POWER GND A-57 — —

A-28 TACHO TACHO A-58 PACL-VCC PTO ACCEL VCC

A-29 N/A (Q CONTROL RESISTOR 1) A-59 IDLUP-VCC IDLE UP VCC

A-30 N/A (Q CONTROL RESISTOR 2) A-60 N/A (SP1 VCC)

-41-

Page 44: izuzu_4hk1

No. Terminal Name Content No. Terminal Name Content

A-61 N/A (ACG-L INPUT) A-79 GL-L GLOW LAMP

A-62 BK1-SW BRAKE 1 SW A-80 MIL CHECK ENGINE LAMP

A-63 BK2-SW BRAKE 2 SW A-81 CRM-L CRUISE MAIN LAMP

A-64 CL-SW CLUTCH SW A-82 AT-TACHO AT-TACHO

A-65 SHUTDOWN-SW ENGINE SHUTDOWN SW A-83 N/A (SP2 GND)

A-66 DIAG CLEAR-SW DIAG CLEAR SW A-84 CRSET-L CRUISE SET LAMP

A-67 EXB-SW EXHAUST BRAKE SW A-85 N/A (SP2)

A-68 — — A-86 IGBC-SW IGNORE BRAKE/CLUTCH SW

A-69 REF-SW REFRIGERATOR SW A-87 N/A (TORQUE LIMIT SW)

A-70 N/A (GLOW MONITOR1 FEEDBACK) A-88 CCDIS-SW CAB CONTROL DISABLE SW

A-71 N/A (TORQUE CUT SW) A-89 SSPA-SW SET SPEED A SW

A-72 N/A (GLOW MONITOR4 FEEDBACK) A-90 SSPB-SW SET SPEED B SW

A-73 +B POWER A-91 RSET-SW REMOTE SET SW

A-74 GL-CONT GLOW CONTOROLLER A-92 RRES-SW REMOTE RESUME SW

A-75 PTOEN-REL PTO ENGAGE RELAY A-93 PTOEN-SW PTO ENGAGE SW

A-76 STAEN-REL STARTER ENABLE RELAY A-94 PTODIS-SW PTO DISABLE SW

A-77 EXB-REL EXHAUST BRAKE RELAY A-95 PTOFB-SW PTO FEEDBACK SW

A-78 N/A (EXHAUST BRAKE LAMP) A-96 STA-SW CRANKING REQUEST SW

No. Terminal Name Content No. Terminal Name Content

B-1 N/A (INTAKE DC MOTOR1) B-22 — —

B-2 N/A (INTAKE DC MOTOR2) B-23 N/A (INCA-BAT)

B-3 COMMON1 INJECTOR POWER1 B-24 PBOOST BOOST PRESSURE SIG.

B-4 COMMON2 INJECTOR POWER2 B-25 PFUEL RAIL PRESSURE SIG.

B-5 COMMON1 INJECTOR POWER1 B-26 PFUEL RAIL PRESSURE SIG.

B-6 COMMON2 INJECTOR POWER2 B-27 N/A (OIL PRESSURE SIG.)

B-7 EBM1 EGR DC MOTOR 1 B-28 MAF MAF SIGNAL

B-8 EBM2 EGR DC MOTOR 2 B-29 INT INTAKE POSITION SIG.

B-9 N/A (EGR BRUSHLESS MOTOR W) B-30 G CAM ANGLE

B-10 — — B-31 NE+ CRANK POSITION+

B-11 N/A (INCA-GND) B-32 NE- CRANK POSITION-

B-12 PB-GND BOOST PRESSURE GND B-33 SCVHI SCV HIGH SIDE

B-13 PFUEL-GND RAIL PRESSURE GND B-34 SCVHI SCV HIGH SIDE

B-14 POIL-GND OIL PRESSURE GND B-35 THW COOLANT TEMP.

B-15 MAF-GND MAF GND B-36 N/A (ENGINE OIL TEMP.)

B-16 INT-GND INTAKE POSITION GND B-37 THA INTAKE AIR TEMP.

B-17 EGR-GND EGR POSITION GND B-38 N/A (EGR-U POSITION SIG.)

B-18 G-SLD CAM ANGLE GND B-39 N/A (EGR-V POSITION SIG.)

B-19 NE-SLD CRANK POSITION GND B-40 N/A (EGR-W POSITION SIG.)

B-20 SCVLO SCV LOW SIDE B-41 THF1 FUEL TEMP

B-21 SCVLO SCV LOW SIDE B-42 N/A (FUEL TEMP. #2)

-42-

Page 45: izuzu_4hk1

< NOTE >• N/A: Component is not mounted (circuit pattern only). Note that the VCC and GND and pin No. A-78 for sensors are

connected inside ECU.

No. Terminal Name Content No. Terminal Name Content

B-43 TWV-D INJECTOR D(CYL2) B-51 G-VB CAM ANGLE VB

B-44 — — B-52 N/A (LOW OIL LEVEL SW)

B-45 TWV-B INJECTOR B(CYL3) B-53 EGR-POS EGR-POSITION SIG. (DC MOTOR)

B-46 PB-VCC BOOST PRESSURE VCC B-54 — —

B-47 PFUEL-VCC RAIL PRESSURE VCC B-55 — —

B-48 POIL-VCC OIL PRESSURE VCC B-56 TWV-C INJECTOR C(CYL4)

B-49 EGR-VCC EGR POSITION VCC B-57 — —

B-50 INT-VCC INTAKE POSITION VCC B-58 TWV-A INJECTOR A(CYL1)

-43-

Page 46: izuzu_4hk1

c. 6HK1 ECU Connector Terminal Layout

d. 6HK1 Terminal Connections

ECU CONNECTOR PIN ASSIGNMENT : 154PIN

Q000543E

No. Terminal Name Content No. Terminal Name Content

A-1 CASE-GND CASE GND A-32 APS2 ACCEL POSITION 2 SIG

A-2 P-GND POWER GND A-33 APS3 ACCEL POSITION 3 SIG

A-3 P-GND POWER GND A-34 PACL PTO ACCEL SIG

A-4 GND ECU SENSOR GND A-35 — —

A-5 GND ECU SENSOR GND A-36 — —

A-6 N/A (Q CONTROL RESISTOR 3) A-37 LFUEL1 FUEL LEVEL 1 SIG

A-7 APS1-GND V5RTN1 A-38 LFUEL2 FUEL LEVEL 2 SIG (ATM TEMP)

A-8 APS2-GND V5RTN2 A-39 VSS+ VEHICLE SPEED SENSOR+

A-9 APS3-GND V5RTN3 A-40 VSS- VEHICLE SPEED SENSOR-

A-10 PACL-GND PTO ACCEL GND A-41 ACG-F ACG-F PULSE INPUT

A-11 — — A-42 — —

A-12 COM-GND COMMON SENSOR GND A-43 2SAXLE-SW 2SPEED AXLE SW

A-13 — — A-44 4WD-SW FOUR WHEEL DRIVE HIGH/LOW SW

A-14 VSS-SLD VSS GND A-45 AC-SW A/C CLUTCH REQUEST SW

A-15 — — A-46 CRM-SW CRUISE ENABLE (ON/OFF) SW

A-16 CAN1-SLD CAN1 SHIELD GND A-47 CRR-SW CRUISE RESUME/ACCEL SW

A-17 CAN1H CAN1 HIGH A-48 CRS-SW CRUISE SET/COAST SW

A-18 CAN1L CAN1 LOW A-49 +B POWER

A-19 N/A (ISO14230) A-50 +B POWER

A-20 CLASS2 J1850 A-51 BATT BATTERY

A-21 CLASS2 J1850 A-52 M-REL POWER MAINTAIN RELAY

A-22 IG0-SW IGNITION 0 (KEY-SW) A-53 M-REL POWER MAINTAIN RELAY

A-23 IG1-SW IGNITION 1 A-54 APS1-VCC VBREF1

A-24 — — A-55 APS2-VCC VBREF2

A-25 — — A-56 APS3-VCC VBREF3

A-26 P-GND POWER GND A-57 — —

A-27 P-GND POWER GND A-58 PACL-VCC PTO ACCEL VCC

A-28 TACHO TACHO A-59 — —

A-29 N/A (Q CONTROL RESISTOR 1) A-60 — —

A-30 N/A (Q CONTROL RESISTOR 2) A-61 ACGL-SW ACG-L INPUT

A-31 APS1 ACCEL POSITION 1 SIG A-62 BK1-SW BRAKE 1 SW

-44-

Page 47: izuzu_4hk1

No. Terminal Name Content No. Terminal Name Content

A-63 BK2-SW BRAKE 2 SW A-80 MIL SERVICE ENGINE SOON LAMP

A-64 CL-SW CLUTCH SW A-81 VSOUT1 4KPPM

A-65 N-SW NEUTRAL SW A-82 VSOUT2 4KPPM (128KPPM)

A-66 DIAG CLEAR-SW DIAG CLEAR SW A-83 — —

A-67 EXB-SW EXHAUST BRAKE SW A-84 ACCL-REL A/C CLUTCH RELAY

A-68 FIDL-SW FAST IDLE SW A-85 — —

A-69 FAXLE-SW FRONT AXLE SW A-86 IGBC-SW IGNORE BRAKE/CLUTCH SW

A-70 LCL-SW LOW COOLANT LEVEL SW A-87 N/A (TORQUE LIMIT SW)

A-71 REV-SW REVERSE SW A-88 CCDIS-SW CAB CONTROL DISABLE SW

A-72 WIF-SW WATER IN FUEL SW A-89 SSPA-SW SET SPEED A SW

A-73 (+B) *1 (POWER) A-90 SSPB-SW SET SPEED B SW

A-74 GL-REL GLOW PLUG RELAY A-91 RSET-SW REMOTE SET SW

A-75 PTOEN-REL PTO ENGAGE RELAY A-92 RRES-SW REMOTE RESUME SW

A-76 STAEN-REL STARTER ENABLE RELAY A-93 PTOEN-SW PTO ENGAGE SW

A-77 EXB-REL EXHAUST BRAKE RELAY A-94 PTODIS-SW PTO DISABLE SW

A-78 FIDL-L FAST IDLE ENGAGE LAMP A-95 PTOFB-SW PTO FEEDBACK SW

A-79 GL-L GLOW LAMP A-96 STA-SW CRANKING REQUEST SW

No. Terminal Name Content No. Terminal Name Content

B-1 AVNT AVNT DRIVE B-23 N/A (INCA-BAT)

B-2 — — B-24 PBOOST BOOST PRESSURE SIG.

B-3 COMMON1 INJECTOR POWER1 B-25 PFUEL RAIL PRESSURE SIG.

B-4 COMMON2 INJECTOR POWER2 B-26 PFUEL RAIL PRESSURE SIG.

B-5 COMMON1 INJECTOR POWER1 B-27 POIL OIL PRESSURE SIG.

B-6 COMMON2 INJECTOR POWER2 B-28 MAF MAF SIGNAL

B-7 EBM-U EGR BRUSHLESS MOTOR U B-29 VNTPOS-SIG VNT POSITION SIG.

B-8 EBM-V EGR BRUSHLESS MOTOR V B-30 G CAM ANGLE

B-9 EBM-W EGR BRUSHLESS MOTOR W B-31 NE+ CRANK POSITION+

B-10 — — B-32 NE- CRANK POSITION-

B-11 N/A (INCA-GND) B-33 SCVHI SCV HIGH SIDE

B-12 PB-GND BOOST PRESSURE GND B-34 SCVHI SCV HIGH SIDE

B-13 PFUEL-GND RAIL PRESSURE GND B-35 THW COOLANT TEMP.

B-14 POIL-GND OIL PRESSURE GND B-36 THO ENGINE OIL TEMP.

B-15 MAF-GND MAF GND B-37 THA INTAKE AIR TEMP.

B-16 VNTPOS-GND VNT POSITION GND B-38 EGR-UPOS EGR-U POSITION SIG.

B-17 EGR-GND EGR POSITION GND B-39 EGR-VPOS EGR-V POSITION SIG.

B-18 G-SLD CAM ANGLE SHIELD GND B-40 EGR-WPOS EGR-W POSITION SIG.

B-19 NE-SLD CRANK POSITION SHIELD GND B-41 THF1 FUEL TEMP

B-20 SCVLO SCV LOW SIDE B-42 THF2 *2 FUEL TEMP. #2

B-21 SCVLO SCV LOW SIDE B-43 TWV-D INJECTOR D

B-22 — — B-44 TWV-F INJECTOR F

-45-

Page 48: izuzu_4hk1

< NOTE >• *1: In case of connecting to outside wiring, note that this terminal is connected to +B inside ECU.

• *2: This terminal is unused.

• N/A: Component is not mounted (circuit pattern only).

No. Terminal Name Content No. Terminal Name Content

B-45 TWV-B INJECTOR B B-52 LOL-SW LOW OIL LEVEL SW

B-46 PB-VCC BOOST PRESSURE VCC B-53 — —

B-47 PFUEL-VCC RAIL PRESSURE VCC B-54 — —

B-48 POIL-VCC OIL PRESSURE VCC B-55 — —

B-49 EGR-VCC EGR POSITION VCC B-56 TWV-C INJECTOR C

B-50 VNTPOS-VCC VNT POSITION VCC B-57 TWV-E INJECTOR E

B-51 G-VB CAM ANGLE VB B-58 TWV-A INJECTOR A

-46-