Installation/Operation Instructions Model 7011, 7031 - Econo-Line ...content.etilize.com/Assembly-Instructions/1015513862.pdf · Model 7031 with Headrest Parts List: Headrest Option

rev. 12282009 cjr ©2009 HAUSMANN INDUSTRIES, INC.

HAUSMANN INDUSTRIES, INC.130 Union St • Northvale NJ 07647 USA • Tel: (201) 767-0255 • Fax: (201) 767-1369 • www.hausmann.com

Installation/Operation InstructionsModel 7011, 7031 - Econo-Line Recovery Couch

Parts List: Standard HardwarePART PART# DESCRIPTION QTYG 7011-007 Glides 5H 7011-008 Plastic Connecting Blocks 8I 7011-009 Phillips #8 1” Screws 8J 7011-010 Metal Dowels 12K 7011-011 Connecting Bolts 12L 7011-012 Allen Wrench 1

Headrest option hardware

A

B C

D

E F

Standard hardware

G

H

I

K

L

J

Tools Required:• Slotted #3 Screwdriver• Phillips #2 Screwdriver• Power Phillips Head Screwdriver• Hammer• Allen Wrench (provided)• 7/16” Ratchet or Box Wrench

Model 7031 with Headrest

Parts List: Headrest Option HardwarePART PART# DESCRIPTION QTYA 7011-001 Headrest hinge mechanism 2B 7011-002 Phillips #8 3/4” screws 4C 7011-003 Phillips #8 1” screws 4D 7011-004 1/4 - 20 3” Carriage bolts 2E 7011-005 Washers 2F 7011-006 1/4 - 20 Locking nuts 2

rev. 12282009 cjr ©2009 HAUSMANN INDUSTRIES, INC.

Assembly Instructions:1. On a smooth surface, lay out the upholstered top and the

(2) side rails with the pre-drilled holes facing each other as shown. (Fig. 1)

2. On units ordered without the headrest option: Install (4) plastic connecting blocks “H” in the pre-drilled holes of the side rail. Orient the blocks so that the screws are protrud-ing towards the closest edge. Use a mallet to fully seat the blocks. Repeat on the second rail which will be a mir-ror image of the fi rst.

On units ordered with the headrest option: Install (4) plas-tic connecting blocks “H” in pre-drilled holes 2, 3 and 4 in each side rail.

3. Install the metal dowels “J” by pushing in and aligning them as shown in picture. At this time you can also insert the metal dowels into the shelf in the same manner. NOTE: Slot must be facing out. (Fig. 2)

4. Align the connecting blocks on the side rail with the track with the pre-drilled holes on underside of top as shown in picture. Tighten the screws in the connecting blocks. DO NOT overtighten. Repeat on second rail. (Fig. 3)

5. Locate the two holes towards the bottom of the outside of either table leg. The outside is the side with (8) visible holes. One of the two holes is closer to the edge of the leg than the other. The legs must be installed so that the hole closer to the edge will be at the front of the unit (towards the side rail which has the track for the doors). (Fig. 4)

Insert the (4) connecting bolts into the pre-drilled holes and secure with the allen wrench provided. Do not fully tighten connecting bolts at this point. The metal dowels may need to be aligned slightly using a fl at head screwdriver in the slot. Turn the metal dowel carefully until the connecting bolts catch. Repeat on second side but do not fully tighten connecting bolts at this point. (Fig. 5)

Underside of Upholstered Top

Track Side

Side Rail with Track

Side Rail less Track

1

1

2

2

3

3

4

4

Fig. 1

J

# 3

Track

Side Rail

Fig. 2

Fig. 3

Side Rail with Track

Side Rail less Track

H

Fig. 5

Side Rail

Panel LegK

FRONT

Fig. 4

2

rev. 12282009 cjr ©2009 HAUSMANN INDUSTRIES, INC.

6. If you have Model 7011, skip to step 13.

7. If you have a headrest option on your table you need to install the headrest hinge mechanism at this point. Using a screw-gun or a Phillips head screwdriver, install the bracket onto the headrest bracket block with (2) #8 1” Phillips head screws “C” into the pre-drilled holes as shown in the picture. Repeat on second headrest bracket. (Fig. 6)

8. Fasten the headrest bracket block to the leg with the (2) carriage bolts and secured with the washer and locknut. Tighten lock nut until secured. The unfi nished side of the headrest bracket block should face away from the underside of the table top.Attach the other end of the bracket hinge to top with (4) screws “B”. (Fig. 7)

9. At this point you will need the help of another person to assist with the installation of the shelf. Make sure the track on the shelf lines up with the track on the side rail before beginning installation. On one side of the leg align the dowels on the shelf with the pre-drilled holes on the leg. Slide down the other side of the shelf until the shelf snaps into place. (Fig. 8)

Fig. 6

Headrest Block

C

Fig. 7

Headrest Block

Carriage Bolt,Locking Nut,Washer

Fig. 8

Leg Panel

Bottom Shelf

Bottom Stretcher

3

Corner of hinge mounting bracket should fi t snug against headrest block

rev. 12282009 cjr ©2009 HAUSMANN INDUSTRIES, INC.

10. Align the dowels of one side of the support rail with the pre-drilled holes on the leg. Push the other side of the support rail towards the center to lock in the sup-port rail. (Fig.8) At this point, go back and tighten the (4) connecting bolts on each of the legs with the allen wrench provided (refer to step 5). Do not overtighten.

11. Secure the shelf by installing (2) connecting bolts “K” in the pre-drilled holes. Repeat on the other leg.

12. Slide the 1/2” back board through the back of the table and fasten with (4) 1” screws provided “I”. From the inside of table fasten the top of the back to inside of the cabinet with (4) 1” screws provided “I”. (Fig. 9)

13. The glides “G” for the table are to be installed on each end of both legs and one on the center of the support rail. You can turn over the table at this point.

14. To install the doors, lift the top of the door into the rear slot of the top track and then align with rear slot of the bottom track and drop into place. Door installa-tion may be easier if you install them in the middle of the shelf span while applying downward pressure on the shelf. Repeat with second door. One door must go on back track and the other door must go on front track. (Fig. 10)

Fig. 9

Bottom Stretcher

Bottom Shelf

Fig. 10

Bottom

Side Rail

4

Please join Hausmann’s effort to reduce paper use and keep the planet green by using our paperless Warranty Registration form. Visit www.hausmann.com and click on Warranty Registration. If you do not have web access or prefer the form be mailed or faxed to you, please call Hausmann Customer Service. As of January 1, 2010, we will no longer include the paper based forms, please visit the online link to fi ll in your Warranty Form.