A3 7 3 4 6 1 Freedom Screens Zipline COMPONENT DIMS - GENERAL SCALE 1:1 at A3 Revision-008 5 2 200mm 66 26 Ø29 70 70 38 17 21 38 16 80 80 60 60 50 50 SCALE 2:3 These alternative housings can be used in place of the default 70mm housing Default Housing **1 1 2 **1 **1 3 5 4 6 7
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
A3
7
3
4
6
1
Freedom Screens ZiplineCOMPONENT DIMS - GENERALSCALE 1:1 at A3Revision-008
5
2
200mm
66
26
Ø29
70
70
38 17
21
38
16
80
80
60
60
50
50
SCALE 2:3
These alternative housingscan be used in place of thedefault 70mm housing
Default Housing**1
1
2
**1
**1
3
5
4
6
7
Min
. 5m
m
Hei
ght M
easu
rem
ent F
ace
Hei
ght M
easu
rem
ent R
evea
l
A3
Mes
h
Face or Floor screw fixings
Mes
h
Freedom Screens ZiplineVERTICAL SECT. - FACE or FLOOR FITSCALE 1:1 at A3Revision-008
Spacer if required to ensure thetracks are in same vertical plane ORMount upper track below thedoor head to maintain verticalalignment (as shown below)
Wall sheet
If upper track is installed below thehead, fit an alum or timber supportto allow vertical adjustment
Door sill
Door head
If lower track is to be recessedrefer to next page for 32Hx39Wchannel information
28m
m
Hei
ght M
easu
rem
ent R
eces
s
A3
Mes
h
Freedom Screens ZiplineVERTICAL SECT. - RECESS TRACKSCALE 1:1 at A3Revision-008
Minimum 28mm clearance must be providedabove the top track to allow for positioning ofthe assembly prior to lowering it into therecessed channel.
Ceiling
If needed fit an aluminium or timbersupport to allow vertical adjustment
Door sill
Door head
Flooring
Use spacer if required under the recess channel
73
73 39
32
A3
Freedom Screens ZiplineDETAIL - RECESS TRACKSCALE 1:1 at A3Revision-008
Recess Cup & Channel are first screwed to floor
Track is then screwed to channel
Recess Cup
Recess Channel
60mm Cup = 63 x 63 x 3270mm Cup = 73 x 73 x 3280mm Cup = 83 x 83 x 32
Recess channel & cup assembly may befitted first to allow flooring to be completed.The screen unit may then be fitted at a laterstage near project completion.
Freedom Screens ZiplinePLAN VIEW - GENERALSCALE 1:1 at A3Revision-008
Door jambDoor jambDoor jamb
A3
OR
OR
Lever
Stile
Lever
Mesh
Receiver
Magnets
Track
Housing
Architrave
Receiver channel used on single screens only.20mm edge to be aligned or proud of door jambto allow clearance for brake lever to rotate
Align front edge ofhousing with door jamb
Align rear edge of housinginto architrave quirk
Width Measurement
Freedom Screens ZiplinePLAN VIEW - STACKER DOORSSCALE 1:1 at A3Revision-008
A3
Lever
Stile
Lever
Sliding Panel
Sliding Panel
Fixed Panel
Mesh
Track
Magnets
Receiver
Housing
Use trim angle to cover gap iffixed panel is set back from sill
Door jamb
Door jamb
Door sill
Width Measurement
Freedom Screens ZiplinePLAN VIEW - BIFOLD DOORSSCALE 1:1 at A3Revision-008
A3
Mesh
Lever
Stile
Lever
Bifold
Panel
Bifold
Panel
Door jamb
Door jamb
Wall sheet
Magnets
Receiver
Track
Door sill
Housing
Width Measurement
Freedom Screens ZiplinePLAN VIEW - DOUBLE DOORSSCALE 1:1 at A3Revision-008
A3
Lever
Stile
Lever
MeshMesh
Lever
Stile
Lever
Wall sheetWall sheet
Door jamb Door jambDoor sill
TrackMagnets
HousingHousing
Width Dimension
Wid
th D
imen
sion
Mes
h
Mesh
A3
Freedom Screens ZiplinePLAN VIEW - INTERNAL CORNERSCALE 1:2 at A3Revision-008
Door sill
Stagger Handle Height
Width Dimension
Wid
th D
imen
sion
Mes
h
Mesh
Freedom Screens ZiplinePLAN VIEW - EXTERNAL CORNERSCALE 1:2 at A3Revision-008
A3
Stagger Handle Height
Door sill
Related Documents
