ENFORCER IP Corner-Mount Camera - SECO-LARM · ENFORCER IP Corner-Mount Camera 2 SECO-LARM U.S.A., Inc. 1x Camera Camera cover CD 2x Mounting screws 1x Pigtail connector 3x Security

ENFORCER IP Corner-Mount Camera

3 SECO-LARM U.S.A., Inc

Mounting screws

DC jack Pigtail connector

Important: Do not cut DC jack or RJ45 jack as warranty will be voided.

RJ45 jack

Camera cover

Security screws

1. Use the included security wrench to loosen the screws and remove the camera cover from the camera.

2. Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the corner where the camera is to be mounted.

3. Execute IP Installer on the PC. 4. Press the Scan button. IP cameras connected to the

same router will be searched and listed. It takes a few seconds. Default IP address is 10.20.30.40.

5. Select the desired product, and press Auto-IP setting button. The windows on the right will appear.

6. Name the camera. 7. Check Http port and number 80. This is an internal port. 8. IP address: You may use auto-scanned IP

192.168.0.254 as it is or you may set Static IP as below: Typical IP setting is as follows. IP address.: 192.168.0.10(you can change the last column) Netmask: 255.255.255.0 Gateway: 192.168.0.1 DNS1/2: You can copy the PC's network properties. This is for internet environments.

9. Input "root" here for User ID and password. 10. Press "Set" to save settings. 11. If you see "Do you want to change network information?"

click "yes". Please wait until the network information gets changed.

12. When IP address is set, you will find the changed IP address "success" in the status column.

13. Double-click the desired device or click "Homepage" after a device from the list.

14. Click "Liveview" on top right of the screen. 15. Click yes for "ActiveX Control".

If the PC is not internet-connected, install SmartViewer.exe from the CD provided with camera.

16. After the installation of Active X or Smart Viewer. You can view live images only with Internet Explorer.

17. Visit http://www.seco-larm.com/EV-N4206-2S4Q for the Web Admin Manual.

1. Please read this manual carefully and keep it for future reference.

2. Use the camera within given temperature and electrical limits.

3. Do not point the camera at the sun. Heat could damage the camera, even when not in use.

4. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.

5. Do not open or disassemble the camera. There are no field-serviceable parts inside.

6. Do not drop the camera or subject it to strong vibrations.

Overview:

Before Starting:

Installation:

ENFORCER IP Corner-Mount Camera

2 SECO-LARM U.S.A., Inc.

1x Camera 1x Camera cover 1x CD 2x Mounting screws 1x Pigtail connector 3x Security screws 1x Security wrench 1x Manual

Model EV-N4206-2S4Q Type Corner-Mount Camera Sensor 1/2.9” 2.43M Sony CMOS Video encoding H.264, MJPEG Resolution 1920x1080, 1280x720, 1024, 640x480, 320x240, 160x120

DNR 2D-NR Yes 3D-NR No

DWDR Yes Scanning system Progressive 1080p # of IR LEDs 30 (940nm) Lens 2.9mm Viewing angle 135° Minimum illumination 0.002 Lux (F/1.8) Gamma correction 0.45 S/N ratio 40dB Gain control Auto White balance Auto Operating voltage 12VDC, PoE 802.3af Current draw 180mA IP Rating IP65 Operating temperature 14°~122° F (-10°~50° C) Dimensions 71/2” x51/2”x111/16” (190x140x43 mm) Weight 13.75-oz (390g)

Specifications:

Dimensions:

Parts List:

71/2” (190mm)

111/16” (43mm)

51/2” (140mm)