Economical Digital Pressure Gauge NIST

Davis Inotek Instruments www.davis.com

H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

676

Digital Pressure Gauge

“Lo-Side” Digital Pressure Gauge

“Hi-Side” Digital Pressure Gauge

SPECIFICATIONSRange 0-99.9 psi (.1 psi resolution)

0-29.9" Hg Vacuum (.1" Hg resolution)Accuracy ± 2% + 1 digit of reading

SPECIFICATIONSRange 0-500 psi (1 psi resolution)Accuracy ± 2% + 1 digit of readingPower Supply 9 VDCLow Battery IndicatorConnection 1⁄4" NPT lower mountMaximum Overload 700 psiAir service or non-corrosive gases1 year warranty

Catalog No. Model Description PriceTI9675 9675 Lo-Pressure Indicator $94.95TI9676 9676 Hi-Pressure Indicator 94.90NISTPR5 — NIST Certificate 85.00NISTPR6 — NIST Certificate with Data 130.00

• Affordably priced• Superior accuracy• Broad range from -14 to 500 psi• Large LCD display• Self contained• 9 volt battery and/or 120 VAC• On/off switch

SPECIFICATIONSScale -14 to 500 PSIOperating 32°F to 120°FTemperature Range Accuracy Better than 1%Resolution 1 PSIDisplay 0.5" LCDPower 9 volt battery or 120 VAC with adapterPressure Port 1⁄8 " NPT male

Includes• 1⁄8" NPT female to 1⁄4" Flare male brass fitting• AC power adapter with 5 foot cord• Calibration screwdriver, storage case

Catalog No. Model Description PriceSC228100 DPG500 Digital Pressure Gauge $134.00

with storage caseNISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate 130.00

with Data

Economical Digital Pressure Gauge NIST it

NIST it

677Davis Inotek Instruments www.davis.com

Pressure / Pressure Calibrators

H

Digital Pressure Gauge NIST it

• Pressure ranges are available to 10,000 PSIG at an accuracy of ± 1%of Full Scale

• One 9 volt alkaline or lithium battery powers the transducer and theLCD display.

• The display is a 4.5 digit LCD with 0.4" high numerals• “Push To Read” key turns the display on for approximately 40 seconds• Automatic shut-off

Catalog No. Description Range PriceMR38001 Digital Pressure Gauge 0 to 50 PSIG $140.00MR38002 Digital Pressure Gauge 0 to 100 PSIG 140.00MR38003 Digital Pressure Gauge 0 to 500 PSIG 140.00MR38004 Digital Pressure Gauge 0 to 1000 PSIG 140.00MR38005 Digital Pressure Gauge O to 1500 PSIG 140.00MR38006 Digital Pressure Gauge 0 to 3000 PSIG 140.00MR38007 Digital Pressure Gauge 0 to 6000 PSIG 140.00MR38008 Digital Pressure Gauge 0 to 10,000 PSIG 140.00

SPECIFICATIONSAccuracy ± 1% of Full Scale at calibrated temperature.Temperature effect ± 0.1% per °FDisplay 4.5 digit LCD (0.4" height), Low battery indicatorPower One 9 volt alkaline battery (included)Enclosure Custom molded ABS plastic housingEngineering Units Available in either PSIG, Bar or kg/cm2Over-Pressure limits twice the full scale rangeField calibration Zero and span adjustment potentiometers are

accessible by removing the back of the caseMedia compatibility Isolated sensor for processes compatible with

17-4 PH stainless steelProcess connection 1/4" male NPTOperating Temp. 32°F to 122°F (0°C to 50°C)

Digital Pressure Gauge

Catalog No. Model Description PriceNH747002 110-2PSIG Digital Pressure Gauge, 2 PSI $325.00NH747020 110-20PSIG Digital Pressure Gauge, 20 PSI 325.00NH747200 110-200PSIG Digital Pressure Gauge, 200 PSI 325.00AccessoriesNH747110 110-Case Molded carrying case 45.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate 130.00

with DataNISTPRQ5 — 2 Year NIST Traceable Certificate 127.00NISTPRQ6 — 2 Year NIST Traceable Certificate 195.00

with Data

DigiGauge 1000

SPECIFICATIONSAccuracy ± 0.25% full scale, ± 1 digitOperating Temperature 0°C to 50°C (32°F to 122°F)Media Compatibility Non-corrosive fluids and gasPower One 9 volt alkaline batteryDimensions 3.25" diameterPressure Connection 1/4" Male NPTWeight 14 oz.

• Industrial Grade: Ruggedly built for industrial use• Pressure Ranges: 2 PSI, 20 PSI and 200 PSI• Accuracy: ± 0.25% full scale• Display: 3.5 digit LCD (0.5" character height)• Power: One 9 volt alkaline battery (included)• Engineering Units: PSI (standard). Other units available (specify)• Pressure Connection: 1/4" Male NPT• Over Pressure Limits: Twice the full scale range• Weight: 14 oz.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

678

Weather Resistant Digital Pressure Gauge

Catalog No. Description PriceTX5881018 Digital Pressure Gauge, 0-20 psig $400.00TX50021 Digital Pressure Gauge, 0-20 psia 450.00TX5881019 Digital Pressure Gauge, 0-100 psig 300.00TX50022 Digital Pressure Gauge, 0-100 psia 350.00TX5881021 Digital Pressure Gauge, 0-500 psig 300.00TX50023 Digital Pressure Gauge, 0-500 psia 350.00TX5881022 Digital Pressure Gauge, 0-1,000 psig 300.00TX50024 Digital Pressure Gauge, 0-1,000 psia 350.00TX5881023 Digital Pressure Gauge, 0-5,000 psig 300.00TX50025 Digital Pressure Gauge, 0-5,000 psia 350.00TX5881024 Digital Pressure Gauge, 0-10,000 psig 300.00TX50026 Digital Pressure Gauge, 0-10,000 psia 350.00AccessoriesTX588104 Auto-Off (Non-standard) 30.00TX5004 Rear Pressure Connection 10.00TX5005 Panel Mounting Flange 30.00TX5881001 Peak Hold 30.00TX5009 Optional Backlight 45.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

• Weather Resistant• Self-Powered by Standard 9 Volt Battery• Large, Full 4 Digit Display with .5 inch Characters• Keypad Operated Microprocessor Circuit has Tare (Auto Zero), Peak

Hold and an Alarm as Standard Functions• Direct Reading to 9999 PSI• A 16 Minute Auto-Off Circuit (4 Minute with Optional Backlight)• 0-5 VDC and 4/20 mA Outputs Available• ± 0.25% of Full-Scale Accuracy

SPECIFICATIONSStandard Pressure Ranges Vacuum to 10,000 psiOverpressure 2x full scale without damageBurst Pressure 10x full scale or 20,000 psig whichever is lessPressure Cavity Volume 0.07 in3 typicalAccuracy (linearity, ± 0.25% of full scalehysteresis, and repeatability)Temperature Range 30°F to 130°FThermal Zero Shift ± 0.02% F.S./°FThermal Sensitivity Shift ± 0.02% F.S./°FResolution (Transducer) Infinite(Display) 1 part in 10,000Life 10 million cycles minimumBatteries/Life Standard 9 volt, 700-900 hours continuous onDisplay 4 digit LCD, .5" DigitsAuto-Off 16 minutes standard, 4 minutes with backlightOperating Temp. Range 0°F to + 160°FCompensated Temp. Range 30°F to + 130°FWetted Materials 15-5 Stainless Steel. 316 S.S. available

NIST it

Mini Digital Pressure Meter SPECIFICATIONSCombined Linearity, Hysteresis and Repeatability ± 0.25% full scale ± 1 digitOver Pressure 3 X the pressure rangeOperating Temperature 0 to 50°CPressure Port 0.2" O.D.Battery Type 9 Volt Alkaline; Life: 100 HoursLow Battery Indication at or below 6.8VDimensions/Weight 3" x 2" x 1.4" / 6.5 oz.

Catalog No. Description PriceNH620103 Pressure/Vacuum Range 199.9/19.9 PSI $219.00NH620104 Pressure/Vacuum Range 1999/19.99 PSI 219.00NH620100 Pressure/Vacuum Range 199.9/199.9 In H2O 219.00NH620102 Pressure/Vacuum Range 1999/199.9 In H2O 219.00NH620106 Pressure/Vacuum Range 19.99 PSI/199.9 cm H2O 219.00Accessories

NH620105 Tubing Fitting Kit 20.00NH031108 Syringe pump for precise generation of pressure and vacuum 3500NH031107 Soft carrying case 20.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

Custom models available, Please inquire

NIST it

• Accuracy ± 0.25% Full Scale• Measures Positive and Vacuum Pressure• Easy to read LCD Display 0.5" 3 1/2 Digit• Only 3" x 2" x 1.4" and weighs only 6.5 oz.• Dual Units, mmHg/PSI or mmHg/In H2O• Media: Non corrosive fluids and gases



H

SPECIFICATIONSAccuracy ± 0.25% full scale plus 1 least significant digit Process connection 1/4" NPT(M)Operating temperature ± 0.25% full-scale accuracy gauges: -4 to 185°F

(-20 to 85°C)Display 3 1/2 digit, 1/2" H LCDMedia compatibility Gases or liquids compatible with 316 stainless steelDimensions 3 3/8" dia., 3 3/8" H x 1 5/8" DWeight 1 lb

Heavy Duty Digital Pressure Gauges NIST it

Catalog No. Range Resolution PriceDPG1000B — Battery Powered Gauges ± 0.25% full-scale accuracyCE2500 0 to 30" Hg 0.1" Hg $259.00CE2501 -15 to 15 psi 0.01 psi 279.00CE2505 0 to 15 psi 0.01 psi 259.00CE2506 0 to 30 psi 0.1 psi 259.00CE2510 0 to 100 psi 0.1 psi 259.00CE2512 0 to 200 psi 0.1 psi 259.00CE2516 0 to 500 psi 1 psi 259.00CE2518 0 to 1000 psi 1 psi 259.00CE2520 0 to 3000 psi 1 psi 279.00CE2522 0 to 5000 psi 1 psi 279.00DPG1000L — Loop Powered Gauges ± 0.25% full-scale accuracy CE2600 0 to 30" Hg 0.1" Hg 289.00CE2604 0 to 15 psi 0.01 psi 289.00CE2606 0 to 30 psi 0.1 psi 289.00CE2610 0 to 100 psi 0.1 psi 289.00CE2612 0 to 200 psi 0.1 psi 289.00CE2616 0 to 500 psi 1 psi 289.00CE2618 0 to 1000 psi 1 psi 289.00CE2620 0 to 3000 psi 1 psi 309.00CE2622 0 to 5000 psi 1 psi 309.00NISTPR5 NIST Traceable Certificate 85.00

Catalog No. Range Resolution PriceDPG1000AD — AC/DC Powered Gauges ± 0.25% full-scale accuracy CE2700 0 to 30" Hg 0.1" Hg $279.00CE2704 0 to 15 psi 0.01 psi 259.00CE2706 0 to 30 psi 0.1 psi 259.00CE2710 0 to 100 psi 0.1 psi 259.00CE2712 0 to 200 psi 0.1 psi 259.00CE2716 0 to 500 psi 1 psi 259.00CE2718 0 to 1000 psi 1 psi 259.00CE2720 0 to 3000 psi 1 psi 279.00CE2722 0 to 5000 psi 1 psi 279.00DPG1000ADA — AC/DC Powered Gauges w/Alarms ± 0.25% full-scale accuracy CE3300 0 to 30" hg 0.1" Hg 349.00CE3304 0 to 15 psi 0.01 psi 349.00CE3306 0 to 30 psi 0.1 psi 349.00CE3310 0 to 100 psi 0.1 psi 349.00CE3312 0 to 200 psi 0.1 psi 349.00CE3316 0 to 500 psi 1 psi 349.00CE3318 0 to 1000 psi 1 psi 349.00CE3320 0 to 3000 psi 1 psi 369.00CE3322 0 to 5000 psi 1 psi 349.00CE6655 115 VAC to 12VDC Adapter for AC/DC gauges 25.00NISTPR6 NIST Traceable Certificate with Data 130.00

Battery-Powered Gauges• Top-accessible zero/span potentiometers• Rugged extruded aluminum case• Five-minute automatic shut off conserves battery life• 1000 hours typical battery life for ± 0.25% full-scale accuracy gauges• 500 hours typical battery life for ± 0.5% full-scale accuracy gauges• Low battery indicationLoop-Powered Gauges• Top-accessible zero/span potentiometers• Rugged extruded aluminum case• Power by 8 to 32 DC, 4 to 20 mA loop max• Reverse polarity protected• Low loop power warning is displayed when power falls below 7.8 VDC• Use TEST button to check loop operation• Three-foot, two-wire electrical connectionAC/DC-Powered Gauges• Top-accessible zero/span potentiometers• Rugged extruded aluminum case• Powered by 8 to 24 VAC, 50/60 Hz or 9 to 32 VDC, 5 mA max• Three-foot, two-wire electrical connectionAC/DC-Powered Gauges with Alarms• Top-accessible zero/span potentiometers• Rugged extruded aluminum case• Power by 8 to 24 VDC, 50/60 Hz or 9 to 32 VDC, 1 W max• Visual LED alarm indicators on front panel• Select high and low setpoints with top potentiometers• Use TEST button to cycle alarms• Two SPDT relay contacts are rated for 1 A at 24 VD and 0.5 A at 115

VAC, noninductive• Three-foot, eight-wire electrical and alarm connection

Model DPG1000BBattery-Powered Gauge

Model DPG1000LLoop-Powered Gauge

Model DPG1000ADAAC/DC Powered Gauge with Alarm

Model DPG1000ADAC/DC Powered Gauge

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

680

Digital Pressure Gauges NIST it

Catalog No. Model Description PriceTX5881011 PG-2000-20 Digital Pressure Gauge 20 PSIA $290.00TX5881012 PG-2000-G Digital Pressure Gauge 0-100 PSI 240.00TX5881013 PG-2000-G Digital Pressure Gauge 0-200 PSI 240.00TX5881014 PG-2000-G Digital Pressure Gauge 0-500 PSI 240.00TX5881015 PG-2000-G Digital Pressure Gauge 0-2,000 PSI 240.00TX5881018 PG-5000-G2 Digital Pressure Gauge 20 PSI 400.00TX5881019 PG-5000-G Digital Pressure Gauge 0-100 PSI 300.00TX5881020 PG-5000-G Digital Pressure Gauge 0-200 PSI 300.00TX5881021 PG-5000-G Digital Pressure Gauge 0-500 PSI 300.00TX5881022 PG-5000-G Digital Pressure Gauge 0-1,000 PSI 300.00TX5881023 PG-5000-G Digital Pressure Gauge 0-5,000 PSI 300.00TX5881024 PG-5000-G Digital Pressure Gauge 0-10,000 PSI 300.00TX5881025 PG-2000-1000-G Digital Pressure Gauge 0-1000 PSI 240.00Options:

TX5881001 — Peak Hold 60.00TX5881002 — Analog output (0-2V) 75.00TX588104 — Auto off, 20 min. standard 30.00TX588105 — Rear pressure connection 10.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

Model PG-5000

Model PG-2000

• Large 4 digit display with 0.5" digits• Battery operated with convenient on/off switch• Optional auto-off circuit with 16 min. standard

delay at no extra cost• Ranges 0-20 psi to 0-9,999 psi (direct reading to

10,000 psi)• Peak-hold and analog output (0-2V) available• Available with .01 psi resolution (100 psi max.)

(optional)

• Large 31⁄2 digit display with 0.5" digits• Battery operated with convenient on/off switch• Ranges -14.7 psi to 2,000 psi• Analog output available (0-2V)• 20 minute auto-off optional at no charge

Economical Replacement for MechanicalGauges

The latest in solid state design, the PG-2000 and PG-5000 incorporate a semiconductor strain gauge pres-sure transducer as the sensing element, conditioned byhybrid electronics. The unit requires very low powerconsumption, resulting in a battery life of 2 years intypical use.Applications

No special tools or adapters are required for installa-tion of the PG-2000 and PG-5000. This makes the unitsan easy and cost effective replacement for less accurate,standard mechanical dial gauges. The units' long life,ease of operation, high accuracy, and low cost make itperfect for all applications where standard 21⁄2 inch orlarger mechanical gauges have been used.

SPECIFICATIONSModel PG-2000 PG-5000Pressure Range 0-20, 0-200, 0-2000 psi 0-20, to 10,000 psi

(any range between points may be specified)Accuracy ± .25% F.S. ± .25% F.S.Display 31⁄2 Digit LCD 4 Digit LCDPeak Hold N/A OptionalAnalog Output (0-2V) Optional OptionalCenter Back Mount Option Optional OptionalGage Pressure Standard StandardAuto Shut-Off Optional OptionalResolution .01 PSI (20 psi range) .01 PSI (20 psi range)Common Specification for both the PG-2000 and PG-5000PERFORMANCE

Overpressure 2X full scale without damageBurst Pressure 10X full scale or 20,000 PSIG whichever is lessPressure Cavity Volume 0.065 inches3

Accuracy (linearity, hysteresis ± .25% of full scaleand repeatability)Compensated Temperature Range 30°F to 130°FThermal Zero Shift ± 0.02% F.S./°FThermal Sensitivity Shift ± 0.02% F.S./°FResolution Transducer Infinite InfiniteDisplay 1 part in 1999 1 part in 9999Life 10 million cycles minimumPHYSICAL

Construction MaterialsCase Injection molded ValoxWetted Materials 15-5 or 17-4 P.H. Stainless Steel. 316 S.S. available at no extra chargeMount All units shipped with Bottom Stem Mount. (Both models may be

ordered with back mount.) All mounts 1⁄4 NPT

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Analog/Digital Pressure Gauge

• Peak Hold• Extra Large Full 4-Digit Display with .75 Characters and 270 Degree

Bar Graph “Analog” Readout• Direct Reading to 10,000 PSI• NEMA 4 Phenolic Housing• Battery Powered with Automatic Light-Actuated Battery-Saver Circuit• Microprocessor-Based Circuit• ± 0.25% of Full Scale Accuracy

SPECIFICATIONSOverpressure 2x full scale without damageCompensated Temp. Range 30°F to 130°FBatteries 1 or 2 Lithium, or 2 alkaline (“C” Size) Operating Temperature 0°F to + 160°FWetted Materials 15-5 or 17-4 P.H. Stainless Steel

Catalog No. Pressure Range 4-20mA Output PriceTX588143 0-50 PSIG NO $375.00TX588145 0-50 PSIG YES 450.00TX588149 0-100 PSIG NO 375.00TX588151 0-100 PSIG YES 450.00TX588155 0-500 PSIG NO 375.00TX588157 0-500 PSIG YES 450.00TX588161 0-1000 PSIG NO 375.00TX588163 0-1000 PSIG YES 450.00TX588173 0-5000 PSIG NO 375.00TX588175 0-5000 PSIG YES 600.00TX588179 0-10,000 PSIG NO 375.00TX588180 0-10, 000 PSIG YES 420.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

Optional Dual Alarm and RS-232 Interface available. Please inquire

NIST it

Catalog No. Model Pressure Range PriceMR39001 3900-GI0010 0 - 10 PSIG $400.00MR39002 3900-GI10050 0 - 50 PSIG 400.00MR39003 3900-GI0100 0 - 100 PSIG 400.00MR39004 3900-GI0500 0 - 500 PSIG 400.00MR39005 3900-GI1000 0 - 1000 PSIG 400.00MR39006 3900-GI1500 0 - 1500PSIG 400.00MR39007 3900-GI3000 0 - 3000 PSIG 400.00MR39008 3900-GI5000 0 - 5000 PSIG 400.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

NEMA 4 Digital Pressure/Process Gauge

SPECIFICATIONSAccuracy ± 0.25% of Full ScaleDisplay 41⁄2 digit LCD (0.6" high)Power Two 9 volt alkaline batteries (included)Enclosure NEMA 4, 316 stainless steelProcess Connection 1⁄4" male NPT, 316 stainless steelOver-Pressure Limits Twice the full scale rangeStorage Temperature -40° F to 158°FOperating 32°F to 158°FWeight 21 ouncesSize 3.77" diameter x 2.25" depth

NIST it

• Selection of Engineering Units

• Field Recalibration• Min/Max• Damping• Shutoff Timer• 41⁄2 digit 0.6" high LCD

Display

With Visual Alarm


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

682

Davis Digital Test Gauge/Calibrator

Catalog No. Model Description LCD Resolution PriceD6551415 65514-15B55 -14.7" Hg Vac to 15 PSI Gauge, bottom connection without mounting flange .001 $595.00D6551421 65514-21B55 -14.7" Hg Vac to 30 PSI Gauge, bottom connection without mounting flange .001 595.00D6551423 65514-23B55 -14.7" Hg Vac to 100 PSI Gauge, bottom connection without mounting flange .01 595.00D6551426 65514-26B55 -14.7" Hg Vac to 300 PSI Gauge, bottom connection without mounting flange .01 595.00D6551427 65514-27B55 -14.7" Hg Vac to 500 PSI Gauge, bottom connection without mounting flange .01 695.00D6551429 65514-29B55 -14.7" Hg Vac to 1000 PSI Gauge, bottom connection without mounting flange .1 695.00D6551432 65514-32B55 -14.7" Hg Vac to 2000 PSI Gauge, bottom connection without mounting flange .1 695.00D6551433 65514-33B55 -14.7" Hg Vac to 3000 PSI Gauge, bottom connection without mounting flange .1 695.00D6551435 65514-35B55 -14.7" Hg Vac to 5000 PSI Gauge, bottom connection without mounting flange .1 745.00OptionsD655771 — Front 300 Series SS Mounting Flange 50.00D655772 — Rear 300 Series SS Mounting Flange 50.00D655773 — Rear Process Connection - 1/4" NPT N/CD20250005 2025-0005 RS-232 Cable and Software 75.00D01460215 0146-0215 Hi-Impact Waterproof ABS Carrying Case with foam lining for handpump and one gauge 225.00Pressure Hand PumpsD8110300 8110-300 Pneumatic Hand Pump, 0-300 PSIG 400.00D8111300 8111-300 Duplex Hand Pump, 0-300 PSIG/0-25" Hg Vac 570.00D81123000 8112-3000 Hydraulic Hand Pump, 0-3000 PSIG 675.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

0.10% of reading accuracy for positive pressure and 1% FS for Vacuum

• 0.10% of Reading Accuracy for Positive Pressure and 1% FS for Vacuum Region

• Intrinsically Safe - Cl1, Div 1, Group A,B,C and DHazardous Areas. CE Mark and Cenelec

• Vacuum Measurement on all Ranges• HI/LO Pressure Query and TARE function• Selectable Engineering Units

Shown with standardbottom connection

NIST it

SPECIFICATIONSAccuracy Positive Pressure: 0.1% of reading from(all effects due to hysteresis, 20 to 100% of FS and 0.02% FS from linearity, repeatability and temperature) 0 to 20% of FS. Vacuum region: 1% of FS

Compensated range -10 to 50 Deg° C (14 to 122 Deg° F) Operating range -20 to 60 Deg° C (-4 to 140 Deg° F)Media Compatibility Materials compatible with 316 SSMax Indicated Pressure At least 110% FS

Maximum Safe Overpressure 200% of Full Scale; 150% FS for 0-5000Display 5-digit LCD - 0.65" digits (99999 counts) Power Supply 3 AA alkaline batt.,- apprx 1500 hours lifeCase Material 300 Series Stainless Steel Pressure Connection 1/4" NPT Male; bottom connectionZero Adjust Range 100 % of Full Scale Size/Weight Approx. 5.8" x 4.8" x 2.5" HWD / 1.4 lbs

Optional carrying casewith pump and gauge

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Digital Pressure Gauges/2-Wire TransmittersEconomical Replacement for Mechanical Gauges

• Low cost• Battery Operated (2 year life continuous use)• Accuracy: ± 0.25% Full Scale• Ranges 0 to 2000 psi (to 10,000 with X 10 multiplier on face)

Catalog No. Model Description PriceDigital Pressure GaugesTX588107 PG6000 Digital Pressure Gauge (0-15 psi) $420.00TX588108 PG6000 Digital Pressure Gauge (0-100 psi) 420.00TX588110 PG6000 Digital Pressure Gauge (0-500 psi) 420.00TX588111 PG6000 Digital Pressure Gauge (0-1,000 psi) 420.00TX588191 PG6000 Digital Pressure Gauge (0-2,000 psi) 420.00Digital Pressure TransmittersTX588115 PG4/20 Digital Pressure Transmitter (0-15 psi) $475.00TX588116 PG4/20 Digital Pressure Transmitter (0-100 psi) 475.00TX588117 PG4/20 Digital Pressure Transmitter (0-200 psi) 475.00TX588118 PG4/20 Digital Pressure Transmitter (0-500 psi) 475.00TX588119 PG4/20 Digital Pressure Transmitter (0-1,000 psi) 475.00TX588122 — Mating electrical connector (Required) 34.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

Absolute ranges and additional psig ranges available upon request

Transmitter Measures Full Scale Pressure Ranges of 0-2000 PSI*, Gauge or Absolute 4-20 mA Output with 31⁄2 Digit LCD Display

SPECIFICATIONSPerformancePressure Ranges 0-15 to 0-2000 psi (to 10,000 with X 10 multiplier)(gauge or absolute)Proof Pressure 2X rangeBurst Pressure 10X full scale, or 20,000 psi, whichever is lessPressure Cavity Volume 0.035 in cubedAccuracy (linearity, ± .25% of full scale (B.F.S.L.)hysteresis, and repeatability) (15 psi 15.0 ± 1 digit)Thermal EffectsZero ± 0.015% F.S./°FSpan ± 0.01% F.S./°FOutput Noise 0.25% P.-P.F.S.Regulation 0.01% F.S. max.Resolution InfiniteLife >10 million cycles

SPECIFICATIONSPERFORMANCE

Standard Pressure Ranges 0-15 to 0-2000 psi (to 10,000 with X 10 multiplier)(gage or absolute)Overpressure 2X full scaleBurst Pressure 10X full scale or 20,000 psi, whichever is lessAccuracy (linearity, hysteresis, ± 0.25% of full scaleand repeatability) (15 psi 15.0 ± 1 digit)Temperature Range 30°F to 130°FThermal Zero Shift ± 0.02% F.S./ °FThermal Sensitivity Shift ± 0.02% F.S./ °FResolution (transducer) InfiniteLife >10 million cyclesELECTRICAL

Battery Pack (2 year life)ENVIRONMENTAL

Storage Temperature -40°F to + 160°FOperating Range 0°F to + 160°FCompensated Range 30°F to 130°FPHYSICAL

Dial size / Fitting 31⁄2“ diameter / 1⁄4" NPT connectorConstruction Materials 17-4 P.H. or 316 S.S.T. (no 0-rings)Display 31⁄2 digit LCD, .5" digitsMedia Compatible with 17-4 P.H. or 316 S.S.T.

NIST it

The PG-4/20 offers the convenience and easyinstallation of a digital gauge with the full capa-bilities of a highly accurate 4-20 mA two-wiretransmitter. The 3

1⁄2 digit LCD display at the

point of measurement, is calibrated in psi or oth-er engineering units, with remote reading or con-trol by computer or microprocessor. The unit de-livers a 4-20 mA output with accuracy of ±.25%F.S. (B.F.S.L.), offers infinite resolution, highburst pressure of 10X F.S., and repeatability better than0.1% F.S.*Ranges to 10,000 PSI with X10 multiplier, Absolute ranges and additional psig ranges available upon request


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

684

Digital Test Gauge

Catalog No. Model Description PriceAccessoriesNISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00NISTPRQ5 — 2 Year NIST Traceable Certificate 127.00NISTPRQ6 — 2 Year NIST Traceable Certificate 195.00

with Data

SPECIFICATIONSPhysical Dial Size: 3˝Case Material: 300 SS, ElectroplolishedSocket Material: 316 SS

DisplayLCD Display Digits,: 4.5Bar Graph: 0 to 100% of rangeBattery-level indicator

Keyboard FunctionsOn/Off: 5 selectable optionsBacklit: 5 selectable optionsMin/Max: stores min & max valuesZero/Clear: zeros display & clears min/max values

Config. ModeEngineering Units: 13 selectable english & metric unitsUpdate Rate: 4 selectable optionsDampening: pressure averaging with 5optionsAuto-Off: 5 selectable optionsLanguages: 7 selectable optionsBacklit: 5 selectable optionsField Recalibration: zero & span options (password protected)Disable Config. Options: password protected

• Accuracy- ± .05% full scale total error band(Includes; terminal point, hysteresis, linearity, repeatability and temperature from -20/150°F)

• Seven Selectable Languages- English- Spanish- French- German- Italian- Portuguese- Dutch

• .66˝ High Characters• For maximum readability

• All-Welded SS Case- NEMA 4, weatherproof, IP65 enclosure

• Field Calibration, Password Protected• Configurable Functions

-12 selectable engineering units- Password protected disable function- Password protected field calibration- 7selectable languages- 7selectable contrast modes

• 1500 Hour Battery Life

ORDERING INFORMATION ASHCROFT® DIGITALPRESSURE GAUGE

To specify the exact digitalgauge required, select entries

from appropriate tables asshown in example below.

1 2 3 4 530 -2089 SD - 02L -100#

1. Dial Size: 3"2. Type: 20893. Wetted Parts: 316 SS4. Connection: 1⁄4 NPT Lower5. Range: 100 psi

ORDERING INFORMATIONCODE PSI* RANGE PRICE

30-2089-SD-02L-vac vacuum $800.00

30-2089-SD-02L-5 5 800.00

30-2089-SD-02L-10 10 800.00

30-2089-SD-02L-15 15 800.00

30-2089-SD-02L-30 30 800.00

30-2089-SD-02L-100 100 800.00

30-2089-SD-02L-160 160 800.00

30-2089-SD-02L-200 200 800.00

30-2089-SD-02L-300 300 800.00

30-2089-SD-02L-600 600 800.00

30-2089-SD-02L-800 800 800.00

30-2089-SD-02L-1,000 1,000 800.00

30-2089-SD-02L-1,500 1,500 800.00

30-2089-SD-02L-2,000 2,000 800.00

30-2089-SD-02L-3,000 3,000 800.00

30-2089-SD-02L-5,000 5,000 800.00

30-2089-SD-02L-7,500 7,500 800.00

*Psi standard with selectable units in: Absolute, in.H2O, ftsw, Bar, mBar,kPa, mPa, mmHg, cmH2O and kg/cm2

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it



H

NEMA 4/NEMA 7 Enclosure Pressure Gauge

• Self-Powered by Long-Life Batteries• Very Large LCD Display• Water, Dust, and Explosion Proof• Automatic Light-Actuated Battery-Saver Circuit• ± 0.25% of Full Scale Accuracy• Optional 4-20 mA output*Class 1, Group B, C, or D

SPECIFICATIONSOverpressure 2x full scale without damageBurst Pressure 10x full scale minimumPressure Cavity Volume 0.065 in3Accuracy (linearity, ± 0.25% of full scalehysteresis, and repeatability)Operating Temperature 30°F to 130°FBatteriesSystem Lithium Thionyl Chloride, (2) cells,

user replaceable, C-sizeLife 2 to 3 years normal operationLow Battery Detection Displays “BAT” when approximately

80% of the capacity is reachedAdjustments Front accessible (removing cover) “Z”

Zero adjust: ± 10% F.S. nom. range“S” Span adjust: ± 20% F.S. nom. range

Pressure Sensor 15-5 or 17-4 P.H. stainless steelEnvironmental Suitable for use in hazardous locations

Class I, Groups B, C, DClass II, Groups E, F, GClass III, NEMA 4

Catalog No. Description PricePressure Gauges — No OutputTX588123 PG3000-20A-0 Pressure Gauge, 0-20 PSIA, no output $450.00TX588125 PG3000-20-0 Pressure Gauge, 0-20 PSIG, no output 400.00TX588192 PG3000-50A-0 Pressure Gauge, 0-50 PSIG, no output 400.00TX588193 PG3000-100A-0 Pressure Gauge, 0 -100 PSIG, no output 400.00TX588194 PG3000-500A-0 Pressure Gauge, 0-500 PSIG, no output 400.00TX588195 PG3000-1000A-0 Pressure Gauge, 0 - 1000 PSIG, no output 400.00TX588196 PG3000-2000A-0 Pressure Gauge, 0 - 2000 PSIG, no output 400.00Pressure Gauges — 4-20mA OutputTX588124 PG3000-20A-4 Pressure Gauge, 0-20 PSIA, 4-20mA output 575.00TX588126 PG3000-20-4 Pressure Gauge, 0-20 PSIG, 4-20mA output 525.00TX588197 PG3000-50A-4 Pressure Gauge, 0-50 PSIG, 4-20mA output 525.00TX588198 PG3000-100A-4 Pressure Gauge, 0 -100 PSIG, 4-20mA output 525.00TX588199 PG3000-500A-4 Pressure Gauge, 0-500 PSIG, 4-20mA output 525.00TX588200 PG3000-1000A-4 Pressure Gauge, 0 - 1000 PSIG, 4-20mA output 525.00TX588201 PG3000-2000A-4 Pressure Gauge, 0 - 2000 PSIG, 4-20mA output 525.00CertificationNISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

NIST it ™

Battery Powered Digital Gage in NEMA 4/NEMA 7* Enclosure for Hazardous EnvironmentsThe PG-3000 Series is a low-cost, high perfor-

mance digital pressure gage powered from twolong-life battery cells. It offers an extra large(0.7 inch) 3.5 digital liquid crystal display withan automatic light actuated circuit which turnsthe unit off in darkness. This can greatly extendthe battery life when used in areas which are notcontinuously illuminated. The long life sensingelement is vibration and shock resistant, and be-ing fabricated from a single block of stainlesssteel provides excellent burst and overpressurecharacteristics.


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

686

Signet Pressure Sensor/Transmitter System NIST it

• psi, Bar, or kPa display

• Integral or remotemounting

• Single point calibra-tion

• Dual input/outputoption

• NEMA 4X/IP65• Large pushbuttons

SPECIFICATIONSProof Pressure 150% of full scaleAccuracy ± 1% of full scaleWetted Materials PVDF, Ceramic, FPM (Viton®)Operating Temperature 0°C to 85°C (32°F to 185°F)Standards CSA, CE, UL Listed

Universal Mount 3-8450 TransmitterCat. No. SG9226303 Price $46.00

Step 2 Choose a Fitting

Step 1 Choose a Pressure Sensor• Standard 3/4" NPT

Process Connection• Flush ceramic diaphragm• Easy installation

SPECIFICATIONSPart No. Wire Power Sensor Input 4 to 20 mA Output Open Collector/Relay3-8450-1 2 1 1 1 O.C. Hi, Lo or Off3-8450-2 4 1 1 2 Relays Hi, Lo or Off3-8450-3 4 2 2 Sensor 1, (Sensor 2 or Delta P) 2 O.C.’s Hi, Lo or Off

Panel Mount 3-8450-XP

All panel mount transmittersinclude everything for panelinstallation. Panel mount trans-mitters fit into a standard 1/4DIN panel cutout.

Integral Mount 3-8452 TransmitterCat. No. SG38052 Price $52.00

The Universal Mount Kit includes a con-duit base, locking ring, and universaladapter for mounting the transmitter on apipe, wall, or other stationary surface.

The integral Mount Kit includes a conduitbase, locking ring, and integral adapterfor mounting the transmitter and sensordirectly onto a pipe.

Field Mount 3-8450-X

Panel Mount 3-8450-XP

• HVAC systems• Scrubbers• Pump Protection• Marine• Water Management• Irrigation Systems• Wastewater

Included

Catalog No. Model Description PriceSG908420 3-2450-1L Pressure Sensor 3/4" male NPT, 0 to 50 psi, 15 ft cable remote $359.00SG908421 3-2450-2L Pressure Sensor 3/4" male NPT, 0 to 50 psi, 6 in cable integral 359.00SG908422 3-2450-1H Pressure Sensor 3/4" male NPT, 0 to 250 psi, 15 ft cable remote 359.00SG908423 3-2450-2H Pressure Sensor 3/4" male NPT, 0 to 250 psi, 6 in cable integral 359.00SG908426 3-2450-1U Pressure Sensor 3/4" male NPT, 0 to 10 psi, 15 ft cable remote 359.00SG908427 3-2450-2U Pressure Sensor 3/4" male NPT, 0 to 10 psi, 6 in cable integral 359.00

Catalog No. Model Description PriceSG384501 3-8450-1 Pressure Transmitter, Field Mount, 1 input $379.00SG384502 3-8450-2 Pressure Transmitter, Field Mount, with relays 450.00SG384503 3-8450-3 Pressure Transmitter, Field Mount, dual input/o utput 645.00SG3845010 3-8450-1P Pressure Transmitter, Panel Mount, 1 input 379.00SG3845020 3-8450-2P Pressure Transmitter, Panel Mount, with relays 450.00SG3845030 3-8450-3P Pressure Transmitter, Panel Mount, dual input/output 645.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

Step 3 Choose a Pressure Transmitter



H

• Ranges 0 to 1 psi through to 10,000 psi• 0.1% FS accuracy• Rugged, lightweight handheld design• Leak test, tare, max/min and filter• °F and °C ambient temperature• Optional pneumatic and hydraulic hand pumps

SPECIFICATIONSMedia Compatibility Differential low side-Clean dry gasses

Differential high side-non corrosive liquids orgassesGauge and absolute sensors-materials compatiblewith stainless steel

Engineering Units PSI, BAR, mBAR, mH2O, in H2O, (4° and 20°C), ft H2O (4° and 20°C), inHg, mmHg, mHg, Pa, hPa, kPa, MPa, kgf/cm2, and one user definable scale

Accuracy ± 0.1% FS including linearity, hysteresis, and repeatability

Temperature Effect ± 0.02% rdg/°CPower Supply 3 x AA alkaline batteries, approx. 300 hours useSize 7.6 x 3.6 x 1.5"Weight 1 lb.

Handheld Pressure Indicators

Catalog No. Model Description PriceDR7051 DPI705 Portable Pressure Indicator, 10 psig $495.00

DR7053 DPI705 Portable Pressure Indicator, 100 psig 495.00

DR7054 DPI705 Portable Pressure Indicator, 300 psig 495.00

DR7055 DPI705 Portable Pressure Indicator, 30 psi absolute 495.00

DR70515 DPI705R Portable Pressure Indicator, 500 psig 795.00

DR113 IS Intrinsically Safe Option 100.00

DPI705 includes basic instrument with internal pressure sensorDPI705R includes basic instrument with remote sensor and cable

NISTPR5 — NIST Traceable Certificate 85.00

NISTPR6 — NIST Traceable Certificate with Data 130.00

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

688

Pressure Tester with 1 Sensor Additional Sensors

PT2500 PT1000 PT2500 PT1000± .025% Accuracy ± 0.10% Accuracy ± .025% Accuracy ± 0.10% Accuracy

Ranges in Inches of Water Cat. No. Price Cat. No. Price Cat. No. Price Cat. No. Price

0.25, 0.5 or 1.0, .07% AS4 $1,785.00 AS6 $860.002.0, 3.0, 5.0, 10.0, 15.0, 25.0, 50.0, 100.0 or 200.0, .06% AS16 1,635.00 AS18 710.00Compound Ranges in Inches of Water

± 0.125, ± 0.25 or± 0.50, .07% AS52 1,635.00 AS54 910.00± 1.0, ± 2.5, ± 5.0, ± 7.5, ± 12.5, ± 25.0, ± 50.0 or ± 100, .06% AS64 1,675.00 AS66 750.00Compound Ranges in PSI - Vacuum/Pressure

5/5, 10/10, 15/15, 15/30 or 15/60 AS100 $1,835.00 AS101 1,715.00 AS102 $910.00 AS103 790.00Ranges in PSI - Gauge

5, 10, 15, 30, 50, 60, 100, 150, 200 or 300 AS120 1,745.00 AS121 1,620.00 AS122 820.00 AS123 695.00500, 600, 1000, 1500, 2000, 2500, 3000, 5000, 6000 or 7500 AS160 1,875.00 AS161 1,745.00 AS162 950.00 AS163 820.00Ranges in PSI - Absolute

5, 10, 15, 30, 50, 60, 100, 150, 200 or 300 AS220 1,835.00 AS221 1,715.00 AS222 910.00 AS223 790.00500, 600, 1000, 1500, 2000, 2500, 3000, 5000, 6000, 7500, 10,000 AS260 1,965.00 AS261 1,835.00 AS262 1,040.00 AS263 910.00Vacuum Ranges in PSI

5, 10 or 15 AS301 1,835.00 AS302 1,715.00 AS264 910.00 AS265 790.00Please specify range and allow approximately 6 weeks for delivery on all Pressure Testers

Optional Accessories

Features at a touch...

The PT indicator is an ex-tremely versatile pressuremeasurement and test instru-ment. Each PT indicator pro-vides the ability to select any ofeight factory programmed engi-neering units, monitor and dis-play minimum and maximumpressure values, programdamping, tare out displayedmeasurement values and com-municate over the standard RS232interface. All these capabilities areaccessible through easy-to-follow keypadfunctions as well as over the RS232 interface.

Catalog No. Description Price

AD2291 Built-in Rechargeable Batteries 95.00AS2292 Back-Lit Liquid Crystal Display 95.00AS2293 316SS Isolation (per sensor) 115.00AS2294 Handle Assembly 115.00


AS2295 Panel Mounting Brackets 25.00

NISTPR100 NIST Traceable Certificate 85.00

NISTPR101 NIST Traceable Certificate with Data 130.00

PERFORMANCE SPECIFICATIONS

Accuracy:PT1000: ± 0.1% of span (.05% of span available at additional cost)PT 2500: ± .025% of span Calibration: (Traceable to N.I.S.T.)Recalibration: Complete recalibration can be accomplished over instru-ment RS232 interface. Zero and span can be accomplished via frontpanel keypad. Resolution: ± 0.002% of span (max)Repeatability: (typical)± 0.01% of span (all psi ranges)± 0.01% of span, (ranges of 1" through 200" H2O)± 0.02% of span, (ranges below 1" H2O)Pressure Types: gauge (sealed gauge over 300 psi), absolute, com-pound, differential and vacuum (as noted in range chart)

MEDIA COMPATIBILITY

Standard:Inches of water ranges clean, dry non-conductive andnon-corrosive gases. Ranges above 500 psi: liquids and gasses compatiblewith 316 SS.Overpressure:Inches of H2O ranges50 psi positive, 15 psi negativepsi ranges200% for ranges of 5 through 1000 psi150% for ranges of 1500 psi and above

PHYSICAL CHARACTERISTICS

Power Requirements:Standard:AC adapter provided for operation off standard110 VDC, 60 Hz supply, 220 VDC, 50 HzOptional:Built-in rechargeable NiCad power pack (consultfactory for availability of alkaline battery powerpack).Battery Life:25 hours (nominal) without back-lighting of LCD.Activation of RS232 interface will result inapproximately a 30% reduction in battery life.

• Push-button zeroadjust

• Min/Max memory• Variable damping

• Selectableengineering units

• Tare• Backlit display

• Port SelectOptions

• Rechargeable batteries

Single/Dual Sensor Pressure Tester NIST it ™

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

• Leak detection in either leak rate or pressure decay modes• Flow velocity and volume measurement using standard pitot tubes

and anubars• Automatic % error calculation simplifies transmitter or transducer cali-

bration• Measurement of pressure, temperature, voltage and current• Two channel — simultaneous measurement and display of pressure,

temperature, voltage or current in any combination• Interchangeable pressure and temperature modules• Programmable damping

SPECIFICATIONSStandard Display Alphanumeric LCD, 0.37-inch height, 2

lines, 16 characters/lineEngineering Units psi, in.H2O, in. Hg, ftSW, bar, mbar,

kPa, Mpa, mmHg, cmH2O, mmH2O and kgcm2 and any single user-programmable engineering unit

Temperature Range 32° to 120°F (0 to 49°C)Electrical Sourcing Specification 24 Vdc at 25 mAElectrical Measurement SpecificationInputs (Volts) Accuracy0/10 Vdc ± 0.025% F.S.0/30 Vdc ± 0.10% F.S.Input (mA) Accuracy0/20 mA ± 0.03% F.S.0/50 mA ± 0.05% F.S.RS232 Serial Interface with 9-pin D type at 300, 1200, 2400,

9600 baudWeight ST-2A Base unit: 3.0 lb (1.4 kg)

Digital Pressure/Leak Indicator

Catalog No. Model Description PriceAS21 ST2A1 Two Line Digital Display Unit with $1,170.00

110 VAC/60 Hz AC AdapterAS22 ST2A2 Two Line Digital Display Unit with 1,195.00

230 VAC/50 Hz AC AdapterAS23 ST2A3 Two Line Digital Display Unit with 1,195.00

100 VAC/50 Hz AC AdapterOptional FeaturesAS300 B Back Lit LCD Display 95.00AS302 N NiCad Batteries (rechargeable) 95.00AS303 A Alkaline Batteries (non-rechargeable) 95.00AS304 H Handle 40.00AS305 L Loop Power Supply 228.00AS306 P Panel Mounting Brackets 25.00AS308 D1 Standard Data Logging Memory & 220.00

High/Low Alarms and Differential Measurement Firmware

AS322 AQS-TC1 TC Interface for J, K, T 415.00RTD Probe Interface AssemblyAS310 AQS-RT1 RTD probe interface assembly for Pt100, 415.00

Ni 120, Cu 10 and other RTDs with resistance outputs of 400 ohms or less

AS311 AQS-RT2 RTD interface assembly for use with Pt1000 415.00RTD probe and other RTDs with resistance outputs of 4000 ohms or less

Catalog No. Model Description PriceRTD Probes

AS312 840X010-01 Pt100 (385), 0.125 diameter, 12 inch length, 275.00handle and 5 ft. coiled cable




AS316 840X010-03 Pt100 (385), 0.125 diameter, 12 inch length, 240.0010 ft. standard cable




AS320 828X136-01 TA4F mating connector for use with AQS-RT 20.00module and our own RTD probes. (probes are supplied with the TA4F connector)



NIST it ™


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

690

Meter automatically senses plug-in transducer’s range and calibration

Heavy Duty Pressure Meter

Catalog No. Model Description PriceEH407495 407495 Heavy Duty Pressure Meter $199.00EHPT30 PT30 30 psi Pressure Transducer 299.00EHPT75 PT75 75 psi Pressure Transducer 299.00EHPT150 PT150 150 psi Pressure Transducer 299.00EHPT300 PT300 300 psi Pressure Transducer 299.00EHPT700 PT700 700 psi Pressure Transducer 299.00EHPT1500 PT1500 1500 psi Pressure Transducer 299.00EH11948062 409997 Soft Vinyl Carrying Case 19.00EH407001 407001 Data Acquisition Program and Cable 69.00NISTRC1 — NIST Traceable Certificate 125.00NISTRC2 — NIST Traceable Certificate with Data 199.00

• Six interchangeable transducers with ranges of 30, 75, 150,300, 700 and 1500 psi

• Displays 8 types of pressure units (bar, psi, Kg/cm2, mmHg,inch/Hg, meter/H2O, inch/H2O and Atmosphere)

• Easy push-button Zero• Push button span adjust provides fine tuning for critical

measurements• Records Max/Min readings with recall• Data Hold and Auto Power Off• Microprocessor design provide simple operation• Accurate to 0.25% of Full Scale + 1 digit• Built-in RS-232 PC interface with optional Windows® 95/98

compatible software• Includes 9V battery and protective rubber holsterInterface Options• Optional Windows®, 95/98 compatible Data Acquisition

Software and serial cable enable user to display and capturereadings on a PC

SPECIFICATIONSSensor Type 30 psi 75 psi 150 psi 300 psi 700 psi 1500 psi

Max. Range (Resolution) Max. Range (Resolution) Max. Range (Resolution) Max. Range (Resolution) Max. Range (Resolution) Max. Range (Resolution)bar 2 (0.002) 5 (0.005) 10 (0.01) 20 (0.02) 50 (0.05) 100 (0.1)psi 29 (0.02) 72.5 (0.1) 145 (0.2) 290 (0.2) 725 (1) 1450 (2)Kq/cm2 2.040 (0.002) 5.095 (0.005) 10.19 (0.01) 20.40 (0.02) 50.95 (0.05) 101.9 (0.1)mm/Hg 1500 (2) 3750 (5) 7500 (10) 15000 (20) 37500 (50) 75000 (100)inch/Hg 59.05 (0.05) 147.6 (0.1) 295.2 (0.2) 590.5 (0.5) 1476 (1) 2592 (2)meter/H2O 20.40 (0.02) 50.95 (0.05) 101.9 (0.1) 204.0 (0.2) 509.5 (0.5) 1019 (1)inch/H2O 802 (1) 2006 (2) 4010 (5) 8020 (10) 20050 (20) 40100 (50)Atmosphere 1.974 (0.002) 4.935 (0.005) 9.87 (0.01) 19.74 (0.02) 49.35 (0.05) 98.7 (0.1)

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Easy Pressure Measuring Systems

Catalog No. Model Description PriceJF7511 75-EPM SYSTEM 1 Low pressure/differential indicator, pump, fittings and case $845.00JF7521 75-EPM SYSTEM 2 Pressure/differential indicator, pump, fittings and case 845.00JF7531 75-EPM SYSTEM 3 Absolute pressure indicator, pump, fittings and case 845.00

AccessoriesNISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00NISTPRQ44 — 2 Year NIST Traceable Certificate 298.00NISTPRQ45 — 2 Year NIST Traceable Certificate with Data 375.00

• Complete system in one case• Fittings and pump included• Selectable units• Intuitive features• Overpressure protection• Compatible with non-corrosive fluids• Backlit display

SPECIFICATIONSSystem 1 System 2 System 3

Model Low Pressure with Differential Pressure with Differential Absolute PressurePressure Range ± 1.9 psi (± 139 mbar) -14.5 - 101 psi (-7 - 7bar) 29 psia (2 bar abs)Accuracy 68-86°F (20-30°C), 0.1% of Reading ± 1% of full scale

14-122°F (-10-50°C), 0.15% of Reading ± 1% of full scalePump Handheld Pneumatic PumpCompatibility Non-Corrosive Liquids and Gases and Non-HydrocarbonsPower Supply (2) AA CellsBattery Life Typically 500 HoursAuto Switch Off 12 minutesLow Battery Indication On DisplayOverpressure Indication On DisplayUnit Measurement 6.1 x 2.6 x 1.6 in (155 x 67 x 40 mm)(L x H x W)Unit Weight 6.4 oz.System Dimensions 15.5 x 13.8 x 4.0 in (395 x 350 x 100 mm)(L x H x W)System Weight 5 lbs (2.3 kg)Operating Temperature 14-122°F (-10 - 80°C)Protection Class IP-65

The EPM-2000 series (Easy PressureManagement) covers a broad variety of applica-tions within pressure measurement. You maymeasure the pressure on your compressor,pneumatic operations, the barometric pressurein energy calculations, level of liquid, water pres-sure, differential pressure on flow measure-ments, pressure control valves, digestion tanksand many others.

With the Ametek EPM-2000 series you can checkthe pressure with ease. All systems are sup-plied with a small air pump with fine adjustmentand vent valve. Hose and fittings are includedenabling you to set up a test/calibration system.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

692

Universal Pressure Vacuum and Temperature Meter

Catalog No. Model Description PriceNH747115 880-02PSIG-KJ Universal Pressure/Vacuum & Temperature Meter 2 PSI to -2 PSI, Temp. K/J type $795.00NH747116 880-02PSIG-YSI Universal Pressure/Vacuum & Temperature Meter 2 PSI to -2 PSI, Temp. YSI type 795.00NH747117 880-10PSIG-KJ Universal Pressure/Vacuum & Temperature Meter 10 PSI to -10 PSI, Temp. K/J type 795.00NH747118 880-10PSIG-YSI Universal Pressure/Vacuum & Temperature Meter 10 PSI to -10 PSI, Temp. YSI type 795.00NH747119 880-30PSIG-KJ Universal Pressure/Vacuum & Temperature Meter 30 PSI to -10 PSI, Temp. K/J type 795.00NH747120 880-30PSIG-YSI Universal Pressure/Vacuum & Temperature Meter 30 PSI to -10 PSI, Temp. YSI type 795.00NH747121 880-60PSIG-KJ Universal Pressure/Vacuum & Temperature Meter 60 PSI to -10 PSI, Temp. K/J type 795.00NH747122 880-60PSIG-YSI Universal Pressure/Vacuum & Temperature Meter 60 PSI to -10 PSI, Temp. YSI type 795.00NH747123 880-100PSIG-KJ Universal Pressure/Vacuum & Temperature Meter 795.00

UniMano 2000

SPECIFICATIONSPressure Ranges 2,10, 30, 60, 100 and 200 PSI full rangeVacuum Range Full range (pressure) or limited to a maximum of -10PSIAccuracy (pressure) 0.1% of full scale reading ± 1 countAccuracy (vacuum) Range ± 0.5% FULL SCALE vacuumPressure Limit Double the maximum rated pressureYSI Temperature Measurement -5°C to 100°CK/J Type Temperature Measurement -40°C to 780°CYSI Temperature Measurement 0.1°CK/J Type Temperature Measurement 0.2°COperating Temperature 0°C to 50°CCompatibility Non corrosive fluids and gasesPressure Connection Lure lockTemperature Connection YSI 7000 - 1/4" phone jack or K/J Type - mini connectorHousing High impact ABS plastic case

• Micro controller based• Pressure/Vacuum and Temperature measurement• 8 engineering units for pressure• YSI 7000 series or Thermocouple K/J type• Auto zero (pressure)• Leak detection (pressure)• Peak hold (pressure)• Absolute pressure models available• High accuracy & resolution• Temperature compensated sensor• Two line 16 character LCD display• Membrane key pad• Compact - palm size

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it



H

NIST itIntrinsically Safe Pressure Vacuum Gauge

Catalog No. Model Description PriceAccuracy 0.05%NH0311171 220-05PSI-UL Pressure/Vacuum Gauge 5PSI to -5PSI $795.00NH0311181 220-20PSI-UL Pressure/Vacuum Gauge 20PSI to -10PSI 795.00NH0311141 220-50PSI-UL Pressure/Vacuum Gauge 50PSI to -10PSI 795.00NH0311151 220-100PSI-UL Pressure/Vacuum Gauge 100PSI to -10 PSI 795.00NH0311161 220-200PSI-UL Pressure/Vacuum Gauge 200PSI to -10PSI 795.00

Custom ranges available, Please inquireAccessoriesNH0311191 CASE-307 Custom molded hard carrying case 47.00NH0311192 220-203C Tubing and connector kit 45.00NISTPR132 — NIST Traceable Certificate 85.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 127.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

DigiMano 2000 UL Certified

SPECIFICATIONSPressure Range 5 PSI, 20 PSI, 50 PSI, 100 PSI and 200 PSIVacuum Range Full range (pressure) or limited to a maximum of -10PSIOver Range 2 x full scale, + countTemperature 0°C to 50°CCompensationResolution 1 part of 10,000Media Compatibility Fluids and gasPower 9 Volt Alkaline BatteryHousing Die-cast aluminum case with sealed membrane switchTransducer Stainless SteelPressure Port 1/8" Male NPT. Adaptable to any standard fitting

using the adapter kit provided

• UL Certified: Ul Certified for safe to use in hazardouslocations Class I, Division I

• Versatile: Pressure and Vacuum, Peak functionFive-Engineering Units (PSI, mBar, InH20, mmHg, CMH20)

• High Accuracy: 0.1% or 0.05% full scale Pressure,0.25% or 0.1% Vacuum

• Rugged: Durable aluminum case• Compact: Palm size• Large Display: 5" high, 4.5 digit LCD display• Compatibility: Wide range of gases and fluids• Choice of Ranges: 5 Pressure ranges to choose from

5 PSI to 200 PSI


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

694

Precision Digital Pressure and Vacuum Gauge

Catalog No. Model Description PriceOrdering Information (0.1% Accuracy)NH747127 220-02CmH2O Precision Digital Pressure/Vacuum $495.00

Gauge 2 PSI to -2 PSINH747128 220-10CmH2O Precision Digital Pressure/Vacuum 495.00

Gauge 10PSI to -10 PSINH747129 220-25CmH2O Precision Digital Pressure/Vacuum 495.00




Gauge 200 PSI to -10 PSIKpa units are available in all models, call for part numbers and pricingOrdering Information (0.05% Accuracy)NH747133 220-05-PSI-05 Precision Digital Pressure/Vacuum 575.00

Gauge 2 PSI to -2 PSINH747134 220-20-PSI-05 Precision Digital Pressure/Vacuum 575.00




Gauge 200 PSI to -10 PSIKpa units are available in all models, call for part numbers and pricingNH0311192 220-203C Tubing & Connector Kit 45.00

(assortment of connectors & tubing)NH031108 204 Syringe Pump - for generating 35.00

controlled pressure/vacuumNISTMA07 — NIST Traceable Certificate 99.00NISTMA08 — NIST Traceable Certificate with Data 130.00NISTMAQ07 — 2 Year NIST Traceable Certificate 148.00NISTMAQ08 — 2 Year NIST Traceable Certificate 195.00

with Data

SPECIFICATIONSPressure Range 2 PSI to 200 PSIVacuum Range Full range (pressure) or limited to a max. of -10 PSIOver Range 2 x full scale rangeTemp. Compensation 0°C to 50°CResolution 1 part of 10,000Power 9 Volt Alkaline battery. AC Adapter OptionalHousing Die-cast aluminum case with membrane switchPressure Port 1/8" FNPT/1/4" FNPT Connector Adapter set included

1/8" MNPT to 1/4" FNPT, 1/8" FNPT to 1/4" Male

DigiMano 2000

• Versatile: Pressure and Vacuum, Peak function. Five engineering units (PSI, mBar, InH2O, mmHg, CmH2O) Kpa units available

• High Accuracy: 0.1% full scale (NIST Traceable)• Rugged: Durable aluminum case• Compact: Palm size• Large Display: 5" high, 4.5 digit LCD display• Compatibility: Wide range of gases and fluids• Cost Effective: Excellent Performance, Price Value• Choice of Ranges: 6 models to choose from 2 PSI to 200 PSI

NIST it

Digital Vacuum Gauge NIST it

Catalog No. Model Description PriceFD100 100-TC Portable Benchtop Digital $399.00

Vacuum Gauge (0-1999 microns)FD101 100-7 Portable Benchtop Digital Vacuum 399.00

Gauge (0-760 torr)NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

The Digivac 100 is a digital vacuum gaugewhich uses time-proven technology and is nowavailable with a wide variety of sensors andranges.

The 100 offers more than just an attractive,rugged design. It uses precision integrated circuits to provide better accuracy and repeatability than analog gauges. Most versions energize the gauge tube with a precision temperature compensated analog current source.

SPECIFICATIONSDisplay .70 inch high, 3 1⁄2 digit, LCDGauge Tube Cable Length 9 FeetSensor Connection 1⁄8" MPT typicalPower AC Adapter 115 VAC 60 hz or 230 VAC 50/60hzSize 2.25 x 5.0 x 5.5

• Accurate• Portable

• Rugged• Fast



H

Vacuum Gauge with Digital and Analog Display

Catalog No. Model Description PriceBR682902 68 29 02 Vacuum gauge DVR 2 with built-in pressure transducer and digital and analogue display. $645.00

With NW 16 small flange connection and screw in nozzle for 6-10 mm I.D. hoses; instructions for useNISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

NIST it

• Reading independent of gas• Digital pressure display enables precise readout• Analogue display is easy to read and provides clear trend indication• Precise, thermally stable pressure reading• Excellent long-time stability• Automatic sleep mode (selectable time setting, factory set: 15 min)• Battery operated• User selectable vacuum units (Torr, mbar, hPa) electronic scale conversion

SPECIFICATIONSMeasuring Range 825 - 1 Torr, 1100 - 1 mbar (hPa)Uncertainty of measurement < +/- 1 Torr/mbar (after proper zero and atmospheric point setting)Power supply built-in, lithium round cells (AA)Connection small flange NW 16 and screw in nozzle for 6-10 mm I.D. hoses (made o PBT)Standards applying conformity with EC low-voltage and EMC directives, conformity with IEC 1010Dimensions (L x W x H) 115 x 115 x 65 mm (with small flange)

Suitable for field or laboratory use, the newVG64 delivers high precision at a low price. It can accurately read vacuum from 12,000 mi-crons down to 0 over a wide temperature range of35°F to 125°F (2°C to 52°C). The vacuum can bedisplayed in user selectable units: Microns(milliTorrs), PSI, milliBars, Inches of Hg andPascals.

Catalog No. Model Description SU6400 V64 Digital Vacuum Gauge $149.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 135.00

Digital Vacuum Gauge

SPECIFICATIONSDisplay Updated every 1/2 second. 1 Micron resolution

below 200 Microns of vacuum Sensor Type ThermistorConnector Type Standard 1/4 inch male flare fitting Vacuum Range 0 - 12,000 Microns (0 - 1,600 Pascals) with

vacuum increasing/decreasing indicator when above 12,000 Microns

Scale Microns, PSI, InHg, milliBars, Pascals, Torr, milliTorr

Operating Temp. Range 35°F to 125°F ( 2°C to 52°C) Overpressure 300 PSI max (20 Bar) Accuracy +/-10% (0 to 1000 Microns) Power Source 9 Volt Alkaline Battery (not included) Continuous Usage Over 35 Hours Auto Shutoff After 10 minutes when vacuum reading is above

12,000 Microns (12 Torr)Dimensions/Weight 5 1/2" H X 3" W X 1 1/4" D / 6.7 ounces

• Reads vacuum in 7 international units • Built-in hanger • Saves battery power • Cleanable sensor • Uses standard 9 Volt battery • Auto shut off

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

• Digital pressure display: precise read out• Analogue display: easy to read, clear trend indication• Separate gauge head with aluminia ceramics transducer with high corrosion

resistance and excellent long-time stability• On the spot measuring and network capability• Gauge head mounted direct to proper spot of vacuum system• Pressure read out at a convenient location• User selectable pressure units (mbar, Torr, hPa)• Electronic scale conversion• Digital calibration at atmosphere and vacuum• Pressure display over four decades• Environmentally friendly: no mercury, no sensitive mechanical components• Conforms with EC Low voltage & EMC directives (class A & B requirements)


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

696

Benchtop Vacuum Gauge

Catalog No. Model Description PriceBR682913 68 29 13 Vacuum gauge DVR 5 Set with calibrated gauge head VSK 5: mains cable with plug $1,190.00NISTHP1 — NIST Traceable Certificate 125.00NISTHP2 — NIST Traceable Certificate with Data 159.00

SPECIFICATIONSMeasuring range 825 - 0.1 Torr, 1100 - 0.1 mbar (hPa)Uncertainty of measurement <+/-1 Torr/mbar +/- 1 digit (after proper zero and atmospheric point setting and at constant temperature)Temperature coefficient <0.07 mbar/KGauge head VSK 5/pressure transducer made of alumnia/ceramicVacuum connection small flange NW 16 and screw-in stepped hose nozzle for 6-10 mm I.D. hoses (made of PBT)Power supply 230 V ~ +/-10% 50-0 Hz or 100-120 V ~50-60 HzDimensions (L x W x H) / Weight 197 x 132 x 87 mm (instrument) / Vacuum gauge 1.4 kg; Gauge head 0.5 kg

Benchtop Vacuum Meter/Controller

Catalog No. Model Description PriceBR683153 68 31 53 Vacuum Controller CVC 2, mains cable with plug according to national standards $1,595.00NISTHP1 — NIST Traceable Certificate 125.00NISTHP2 — NIST Traceable Certificate with Data 159.00

SPECIFICATIONSPressure transducer piezoresistive absolute pressure transducer, integrated into the unit with anticorrosion designVacuum connection stepped hose nozzle PBT for hoses with 6-10 mm inner diameterMeasuring range 975 - 1 Torr, 1300 mbar - 1 mbar (hPa) (~1200 Torr)Uncertainty of measurement <0.5% of measuring range (after proper adjustment at zero and atmospheric point setting and at constant temperature)Operating temperature 0°C - 40°CPower supply 100-120 V~50-60 Hz or 230 V ~ +/-10% 50-60 HzDimensions (L x W x H) / Weight 240 x 132 x 87 mm / 1.5 kg

NIST it

NIST it

• Manual or semi-automatic determination of process pressure setting• Automatic setting of pressure intervals, manual facility override• Analogue display provides clear trend indication• Electronic scale conversion for the most common pressure units• Digital calibration• Overpressure indication• Integrated electrical overload protection: short circuit proof

transformer (no fuses)• Low electromagnetic radiation: metal housing, radio frequency interference filter for

protection of sensitive nearby instruments, high immunity from electromagnetic noise• Basic unit of the Vacuum Management System VMS



H

Mini-DifferentialPressure Gauges

Combining highaccuracy, readability,compactness, dependability,and low cost.

SPECIFICATIONSAmbient Temperature Range 20° to 140°FPressure Rating -20 Hg to 15 psigAccuracy ± 2% of full scale (3% on 0 and 4% on 00 ranges)

throughout range at 70°FConnections 1⁄8" NPT high and low pressure taps, duplicated—

one pair on side and one pair on back

Catalog No. Model Range (in. H2O) Minor Div. Price

DW33501 2000-00 0 to .25 .005 $62.00DW33502 2000-0 0 to .50 .01 56.00DW33503 2001 0 to 1.0 .02 56.00DW33504 2002 0 to 2.0 .05 56.00DW33505 2003 0 to 3.0 .10 56.00DW33506 2004 0 to 4.0 .10 56.00DW33507 2005 0 to 5.0 .10 56.00DW33510 2010 0 to 10 .20 56.00DW33511 2015 0 to 15 .50 56.00DW33512 2020 0 to 20 .50 56.00DW33513 2025 0 to 25 .50 56.00DW33514 2030 0 to 30 1.0 56.00DW33515 2040 0 to 40 1.0 56.00DW33516 2050 0 to 50 1.0 56.00DW33519 2100 0 to 100 2.0 56.00DW33520 2150 0 to 150 5.0 56.00Catalog No. Model Range Zero Center Minor Div.

(in. H2O)

DW33521 2300-0 .25 to 0 to .25 .01 61.50DW33522 2301 .5 to 0 to .5 .02 61.50DW33523 2302 1 to 0 to 1 .05 61.50DW33525 2310 5 to 0 to 5 .20 61.50DW33527 2330 15 to 0 to 15 1.0 61.50

Catalog No. Model Range PSI Minor Div.

DW33530 2203 0 to 3 .10 56.00

DW33533 2210 0 to 10 .20 90.50

*These ranges are equipped with medium pressure (MP) option, standard. (rated 35 psig)

DUAL SCALE AIR VELOCITY UNITS

Catalog No. Model Range Range, (in. H2O) Air Velocity F.P.M.

DW33536 2000-00AV 0 to .25 300 to 2000 62.00

DW33537 2000-0AV 0 to .50 500 to 2800 56.00

DW33538 2001AV 1 to 1.0 500 to 4000 56.00

DW33539 2002AV 1 to 2.0 1000 to 4000 56.00

DW33540 2010AV 0 to 10 2000 to 12500 56.00

Catalog No. Model For 2000 Series Gauges

DW33582 A610 Type Mounting Kit for mounting a magnahelic on vertical or 13.00horizontal on 1⁄4" x 2" pipe. Includes steel mounting plate, Includes steel mounting plate with 2 “U” clamps, nuts and lockwashers.

DW33584 ASF Adjustable Signal Flag 12.00

DW33585 A432 Portability Kit (Includes carrying case, 23.25standard hold bracket, tubing and terminal tube with holder)

DW33586 A605 Air Filter Kit (2 static pressure tips and other 23.25accessories to turn unit into air filter gauge)



SPECIFICATIONSAmbient Temperature Range 20° to 120°FRated Total Pressure 50 psig surge, 30 psig continuousAccuracy ± 5% of full scale at 70°FConnections 2- Barbed for 3⁄16" ID tubingHousing Polycarbonate and glass filled nylon,

high impact acrylic lens

These gauges are used to measure fan and blower pressures,filter resistance, air velocity, furnace draft, pressure drop acrossorifice plates, liquid level with bubbler systems. Can be flush orsurface mounted. Requires 49⁄16" hole for flush, panel mount. Alsoavailable as a pressure switch/gauge.

Differential Pressure Gauge Series 2000 NIST it

Catalog No. Model Description/Gauge PriceDW33660 2-5000-0 Pressure Gauge 0 to .50" w.c. $44.00DW33661 2-5001 Pressure Gauge 0 to 1.0" w.c. 44.00DW33662 2-5002 Pressure Gauge 0 to 2.0" w.c. 44.00DW33664 2-5005 Pressure Gauge 0 to 5.0" w.c. 44.00

Catalog No. Model Description/GaugeDW33675 A-497 Surface Mounting Bracket: 3.75

For the Mounting of the Minihelic Gauge DW33676 A-609 Air Filter Kit Mounting Kit with Two Static 34.25

Pressure Tips, Two Molded Vent Valves, Two 5 ft. lengths of 1⁄4" Aluminum Tubing and Necessary Adapters

NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

Indicates Low Air or Gas Pressures of Positive, Negative or Differential


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

698

Dwyer Differential Pressure Gauge Series 4000Measure Pressures of Gas, Air or Liquids

NIST it

Catalog No. Model Range Minor Div. Price(in. H2O)

DW33401 4000-0 0 to .50 .01 $246.00DW33403 4002 0 to 2.0 .05 246.00DW33406 4005 0 to 5.0 .10 246.00DW33409 4010 0 to 10 .20 246.00DW33411 4020 0 to 20 .50 246.00DW33412 4025 0 to 25 .50 246.00DW33414 4040 0 to 40 1.0 246.00DW33418 4100 0 to 100 2.0 246.00DW33420 4200 0 to 200 5.0 246.00DW33423 4500 0 to 500 10.0 246.00

Catalog No. Model Range PSI Minor Div.

DW33432 4201 0 to 1 .02 246.00

DW33436 4205 0 to 5 .10 246.00

DW33438 4215 0 to 15 .50 246.00

DW33440 4230S 0 to 30 1.0 246.00

DW33442 4260S 0 to 60 2.0 246.00

Catalog No. Model Description

DW33484 ASF Adjustable Signal Flag 14.00DW33485 A314 Bleed Fittings for Wet Gases 5.75DW33486 B Forged Brass Case 92.00

(for applications involving water or water based liquids)DW33487 A471 Portability Kit Complete 308.00

(includes portable case, equalizer and shut off manifold, and two ten foot lengths of hose)



Catalog No. Model Description Price

DW33931 3000-00 0 to .25" H2O .005 Divisions $223.00DW339321 3001 0 to 1.0" H2O .02 Divisions 216.50DW33934 3003 0 to 3.0" H2O .10 Divisions 216.50DW33936 3005 0 to 5.0" H2O .10 Divisions 216.50DW33939 3010 0 to 10" H2O .20 Divisions 216.50DW33940 3015 0 to 15" H2O .50 Divisions 216.50DW33948 3100 0 to 100" H2O 2.0 Divisions 216.50NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

Dwyer Pressure Switch/Gauges NIST it

SPECIFICATIONSAmbient 20°F to 120°F. Low temperature models available Pressure Range as an optionRelated Pressure 20" Hg to 25 psig total pressure on either side of Photohelic diaphragm. MP Model to 35 psig and HP Model to 80 psig

also available. Capsuhelic, 20 Hg to 500 psigAccuracy Photohelic, ± 2% of full scale at 70° (3% on “O" models,

4% on “OO” models. Capsuhelic, ± 3% of full scale at 70°(2% on 4300 S models, 4% on 43215, 43220, 43500)

Gauge Connection Photohelic, 1⁄8" NPT. Capsuhelic, 1⁄4" NPTElectrical Ratings 10 amps at 110 VAC, 60 Hz resistive(Of relays) 6 amps at 240 VACPower Required 120 VAC, 50/60 HzConduit Opening 3⁄4" conduit

The photohelic switch/gauges function in thesame manner, as versatile, precise pressureswitches combined with a pressure gauge utilizingthe time proven magnehelic design. Availablewith 1 or 2 LED/phototransistor actuated relays.Gauge reading is unaffected by switch operation.Easy to adjust set points with knob controls.Apply pressure and switch set points are fully vis-ible. Deadband is 1 pointer width—less than 1%full scale. DPDT relays can easily be interlockedto provide variable deadband control. For positive,negative or differential pressures as low as 0.25"water column to 0 to 300 psi full scale; set pointsas low as .01 w.c. on .25" scale unit.

For air or compatible gases or liquids.Measures pressure, vacuum or differential.Suitable for internal pressures to 500 psig.May be flush or surface mounted. 5" diameter,requires a 413⁄16" hole for flush mounting.



H

Differential Pressure Gauges

SPECIFICATIONSModel Number 120Differential 0-10 PSID to 0-110 PSIDPressure RangeAccuracy ± 3-2-3% F.S.Dial Size 2 1⁄2 " Round (STD.)Working Pressure 6,000PSIGOperating Temperature -40°F (-40°C) to + 200°F (+ 93°C)Body Materials Aluminum or 316S.S.Internal Materials 316 Stainless SteelMounting & Connections 1⁄4" FNPT Back Conn. (STD.)Gauge Design Magnetically-Coupled

Piston-TypeBase Dimensions 3.3" x 1.97" x 4.25"Base Weight 1.0 lbsSeal BUNA N (STD) Others available

upon requestConnections 1⁄4" Back Connections (STD)

Differential Pressure Gauge

Catalog No. Model Material Range PriceWW238 120-AA-00-00 Aluminum 0 to 10P.S.I.D. $105.00WW242 120-AA-00-00 Aluminum 0 to 30P.S.I.D. 105.00WW243 120-AA-00-00 Aluminum 0 to 50P.S.I.D. 105.00WW249 120-AA-00-00 Aluminum 0 to 1.6 bar 105.00WW255 120-SA-00-00 Stainless Steel 0 to 10P.S.I.D. 204.00WW260 120-SA-00-00 Stainless Steel 0 to 50P.S.I.D. 204.00WW263 120-SA-00-00 Stainless Steel 0 to 100P.S.I.D. 204.00NISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00

NIST it

• Working pressure 6000P.S.I.G.• Over-range protection to rated working

pressure• Aluminum housing with 316 stainless

steel internals

• Weather resistant construction standard• Accuracy ± 5% full scale ascending.

(± 3 -2 -3% full scale) • Shatter resistant lens• 21⁄2" or 41⁄2" dial

Differential Pressure Gauges NIST it

Ideally Suited for Use on Dissimilar Fluids, Wet Gas or Fluids with a High Concentration of Solids.

SPECIFICATIONS

Differential Range 0-50" H2O to 0-100 PSIDAccuracy ± 3-2-3%F.S.Dial Size (1) 21⁄2" round (std.)Working Pressure 3000 PSIG-alum, 316SS

1500 PSIG-brassInternal Materials 316S.S. & elastomer

diaphragm

Connection 1⁄4" FNPT back conn. (std.)Gauge Design Magnetically-coupled

diaphragm-typeDimensions/ Weight 3.3" x 2.75" x 5.41" / 2.75 lbSeal BUNA (std)Connections 1⁄4" FNPT back (std)

140 Differential Pressure Gauge/Aluminum Body

Cat. No. Model Material Range PriceWW272 141-AA-00-00 Aluminum 0-50 H20 $165.00WW273 141-AA-00-00 Aluminum 0-60 H20 165.00WW274 141-AA-00-00 Aluminum 0-75 H20 165.00WW275 141-AA-00-00 Aluminum 0-100 H20 165.00WW277 141-AA-00-00 Aluminum 0-150 H20 165.00WW279 141-AA-00-00 Aluminum 0-300 H20 165.00WW280 141-AA-00-00 Aluminum 0-400 H20 165.00WW281 141-AA-00-00 Aluminum 0-5P.S.I.D. 165.00WW282 141-AA-00-00 Aluminum 0-10P.S.I.D. 165.00WW284 141-AA-00-00 Aluminum 0-20P.S.I.D. 165.00WW286 140-AA-00-00 Aluminum 0-30P.S.I.D. 195.00WW287 140-AA-00-00 Aluminum 0-50P.S.I.D. 195.00WW289 140-AA-00-00 Aluminum 0-75P.S.I.D. 195.00WW290 140-AA-00-00 Aluminum 0-100P.S.I.D. 195.00WW291 140-AA-00-00 Aluminum 0-1.0 bar 195.00WW293 140-AA-00-00 Aluminum 0-2.5 bar 195.00WW294 140-AA-00-00 Aluminum 0-4.0 bar 195.00WW295 140-AA-00-00 Aluminum 0-6.0 bar 195.00WW296 140-AA-00-00 Aluminum 0-7.0 bar 195.00NISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00

140 Differential Pressure Gauge/Brass Body

Cat. No. Model Material Range PriceWW297 141-BA-00-00 Brass 0-50 H20 $220.00WW298 141-BA-00-00 Brass 0-60 H20 220.00WW299 141-BA-00-00 Brass 0-75 H20 220.00WW300 141-BA-00-00 Brass 0-100 H20 220.00WW302 141-BA-00-00 Brass 0-150 H20 220.00WW304 141-BA-00-00 Brass 0-300 H20 220.00WW305 141-BA-00-00 Brass 0-400 H20 220.00WW306 141-BA-00-00 Brass 0-5P.S.I.D 220.00WW307 141-BA-00-00 Brass 0-10P.S.I.D. 220.00WW309 141-BA-00-00 Brass 0-20P.S.I.D. 220.00WW311 140-BA-00-00 Brass 0-30P.S.I.D. 250.00WW312 140-BA-00-00 Brass 0-50P.S.I.D. 250.00WW314 140-BA-00-00 Brass 0-75P.S.I.D. 250.00WW315 140-BA-00-00 Brass 0-100P.S.I.D. 250.00WW316 140-BA-00-00 Brass 0-1.0 bar 250.00WW318 140-BA-00-00 Brass 0-2.5 bar 250.00WW319 140-BA-00-00 Brass 0-4.0 bar 250.00WW320 140-BA-00-00 Brass 0-6.0 bar 250.00WW321 140-BA-00-00 Brass 0-7.0 bar 250.00NISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00

140 Differential Pressure Gauge/316 Stainless Steel Body

Cat. No. Model Material Range PriceWW322 141-SA-00-00 316 S.S. 0-50 H20 $305.00WW323 141-SA-00-00 316 S.S. 0-60 H20 305.00WW324 141-SA-00-00 316 S.S. 0-75 H20 305.00WW325 141-SA-00-00 316 S.S. 0-100 H20 305.00WW327 141-SA-00-00 316 S.S. 0-150 H20 305.00WW329 141-SA-00-00 316 S.S. 0-300 H20 305.00WW330 141-SA-00-00 316 S.S. 0-400 H20 305.00WW331 141-SA-00-00 316 S.S. 0-5P.S.I.D. 305.00WW332 141-SA-00-00 316 S.S. 0-10P.S.I.D. 305.00WW334 141-SA-00-00 316 S.S. 0-20P.S.I.D. 305.00WW336 140-SA-00-00 316 S.S. 0-30P.S.I.D. 355.00WW337 140-SA-00-00 316 S.S. 0-50P.S.I.D. 355.00WW339 140-SA-00-00 316 S.S. 0-75P.S.I.D. 355.00WW340 140-SA-00-00 316 S.S. 0-100P.S.I.D. 355.00WW341 140-SA-00-00 316 S.S. 0-1.0 bar 355.00WW343 140-SA-00-00 316 S.S. 0-2.5 bar 355.00WW344 140-SA-00-00 316 S.S. 0-4.0 bar 355.00WW345 140-SA-00-00 316 S.S. 0-6.0 bar 355.00WW346 140-SA-00-00 316 S.S. 0-7.0 bar 355.00NISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

700

Standard Duty Differential Test Kits

Rugged mediumaccuracy portabletest kits. Popular ap-plications are balanc-ing heating & coolingsystems, checkingpump performance,local flow indication,checking equipmentfor excessive pressuredrop, leakage.

SPECIFICATIONSModel 820 Model 831 Model 841

Accuracy ± 3-2-3% ± 3-2-3%F.S. ± 3-2-3 % AscendingAscending Ascending

Dial Size 21⁄2" 41⁄2" 21⁄2"Working Pressure 500P.S.I.G. (34 bar) STD 300P.S.I.G. (20 Bar) 500P.S.I.G. (34 Bar)

Note: Pressure rating shown is limited by the hoses or by the gauge, whichever is lower. Higher ratings are available as an option. (Contact factory for details)

STANDARD MATERIALS OF CONSTRUCTION

Gauge Aluminum/316 S.S. Internals Polysulfone/316SS Int'ls. Alum/316SS Int'ls.Valves NONE Soft-Seated Brass NONETubing & Fittings Nylon & BrassHoses & End Ftgs Neoprene Jacket and Liner. Schrader 1.4" Brass CouplerCase Polypropylene Polyethylene PolypropyleneHose Length 5Ft. (1.5 Meters) 10Ft. (3 Meters)Fitters All Test Kits are protected with 90 Micron Brass Filters to minimize plugging with scale, sand, etc.

Filter elements can be cleaned or replacedTemperature Limitations Maximum 150°F (66°C) Freezing temperatures must be avoidedOptional Features A wide variety of materials, working pressures and fittings is available

Catalog No. Model Description PriceWW353 820 Test & Flow Measuring Kit Range 0-25 ft./H2O $335.00WW361 820 Test & Flow Measuring Kit Range 0-60 ft./H2O 335.00WW362 820 Test & Flow Measuring Kit Range 0-100 ft./H2O 335.00WW354 831 Test & Flow Measuring Kit Range 0-16 ft./H2O 640.00WW363 831 Test & Flow Measuring Kit Range 0-35 ft./H2O 640.00WW355 841 Test & Flow Measuring Kit Range 0-25 ft./H2O 390.00WW364 841 Test & Flow Measuring Kit Range 0-60 ft./H2O 390.00WW365 841 Test & Flow Measuring Kit Range 0-100 ft./H2O 390.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

High quality portable test kits for precise flow indication, leak detec-tion, balancing heating & cooling systems, checking pump performance,and checking calibration of transmitters, etc.

SPECIFICATIONSModel 805Accuracy ± 1% Full Scale-StandardDial Size 4 1⁄2 "-StandardWorking Pressure NOTE: Pressure rating shown is limited by the hoses. Higher ratings are available as an option. Please inquire.STANDARD MATERIALS OF CONSTRUCTION

Gauge Aluminum Capsule/Brass InternalsValves Soft-Seated BrassTubing & Fittings Nylon & BrassHoses & End Ftgs. Neoprene Jacket and Liner. Schrader 1.4" Brass CouplerCase PolyethyleneHose Length 10Ft. (3 Meters)Filters All Test Kits are protected with 90 Micron Brass Filters to minimize plugging with scale, sand, etc.

Filter elements can be cleaned or replacedTemperature Limitations Maximum 150°F (66°C) Freezing temperatures must be avoidedOptional Features A wide variety of materials, working pressures and fittings are available, Please inquire

Catalog No. Model Description PriceWW347 805 Test & Flow Measuring Kit Range 0-25 in./H2O $1,450.00WW348 805 Test & Flow Measuring Kit Range 0-50 in./H2O 1,205.00WW349 805 Test & Flow Measuring Kit Range 0-100 in./H2O 1,205.00WW351 805 Test & Flow Measuring Kit Range 0-200 in./H2O 1,205.00WW357 805 Test & Flow Measuring Kit Range 0-100 ft./H2O 1,205.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

Precision Differential Pressure Test Kits NIST it


H

702

Pres

sure

/ Pr

essu

re C

alib

rato

rs

MODEL 1490 SPECIFICATIONS Accuracy ± 2-1-2% full scaleDial Size 21⁄2"Connection Standard: 1⁄4" NPT lower mount

or 1⁄8 NPT MaleOptional: 1⁄4" NPT back mount

Case Glass-filled PolysulfoneWindow PolycarbonateBourdon Tube Beryllium copper

diaphragmSocket Brass

MODEL 1005 SPECIFICATIONS Accuracy ± 3 - 2 - 3% full scaleDial Size 21⁄2"Connection Standard: 1⁄4" NPT lower mount

Optional : 1⁄4" NPT back mount

Case Black painted steelWindow Polycarbonate push-inBourdon Tube Bronze (VAC 600psi and compound)

Helical bronze (1000 to 6000psi)Socket Brass

Low Pressure and Commercial Pressure Gauges

Model 1490 Features• 2 1⁄2" and 3 1⁄2" dial size• Glass-filled polysulfone casematerial

• Beryllium copper diaphragm• Brass socket• Wetted materials of berylliumcopper, brass, polysulfone andRTV silicone

• Optional back mount available

Model 1005 Features • Case material is black painted

steel• These gauges utilize a heat

resistant push-in polycarbonatewindow

• Dial faces match other commercialgauges for easy readability

• Patented PowerFlex with polyestersegment movement

• Optional back mount available

Low Pressure Gauge Model 1490 2 1⁄2" DialCatalog No. Range PriceAS1461 0 to 10 oz./sq. in. $36.40AS1462 0 to 15 oz./sq. in. 36.40AS1463 0 to 20 oz./sq. in. 36.40AS1464 0 to 30 oz./sq. in. 36.40

VacuumAS1465 15" to 0 H2O 40.90AS1466 30" to 0 H2O 40.90AS1467 0 to 60" H2O 40.90AS1468 1 to 100" H2O 40.90AS1469 0 to 200" H2O 40.90

Inches H2OAS1490 0 to 10" H2O 36.40AS1491 0 to 30" H2O 36.40AS1492 0 to 60" H2O 36.40AS1493 0 to 100" H2O 36.40AS1494 0 to 200" H2O 36.40AS1495 0 to 300" H2O 36.40

PSIAS1496 0 to 3 PSI 36.40AS1497 0 to 5 PSI 36.40AS1498 0 to 10 PSI 36.40

CompoundAS1499 10"/0/10"H2O 40.90AS1500 30"/0/30"H2O 40.90NISTPR68 NIST Traceable Certificate 85.00NISTPR69 NIST Traceable Certificate with Data 130.00

Standard metric ranges available, kPa and cm H2O

Commercial Pressure Gauge Model 1005 2 1⁄2" DialCatalog No. Range PriceAS105200 15 PSI $19.20AS105201 30 PSI 19.20AS105202 60 PSI 19.20AS105203 100 PSI 19.20AS105204 160 PSI 19.20AS105205 200 PSI 19.20AS105206 300 PSI 19.20AS105207 400 PSI 19.20AS105208 600 PSI 19.20

VacuumAS105209 30" HG VAC 20.20

Compound

AS105210 30" HG/0/15 PSI 20.20

AS105211 30" HG/0/60 PSI 20.20

AS105212 30" HG/0/100 PSI 20.20

AS105213 30" HG/0/300 PSI 20.20



Model1490

Model1005

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Model 1009 21⁄2" Dial 31⁄2" Dial

Range Catalog No. Price Catalog No. Price0-15psi AS109201 $77.80 AS109215 $89.700-30psi AS109202 77.80 AS109216 89.700-100psi AS109203 74.40 AS109217 85.800-200psi AS109204 74.40 AS109218 85.800-400psi AS109205 74.40 —0-1000psi AS109207 74.40 —0-5000psi AS109209 82.60 AS1092230-10,000psi AS109210 82.60 AS109224Vacuum 30"HG to 0 AS109211 77.80 AS109225 89.70Compound 30"HG to 0-15psi AS109212 77.80 —

30"HG to 0-100psi AS109213 77.80 —

Model 1008 21⁄2" Dial Liquid Filled 4" Dial (100mm) Liquid FilledDual Range0-15psi, 100Kpa AS108301 56.30 AS92103 108.000-60psi, 400Kpa AS108302 53.80 AS92105 102.000-100psi, 700Kpa AS108303 53.80 —0-200psi, 1400Kpa AS108304 53.80 AS92107 102.000-400psi, 2800Kpa AS108305 53.80 —30"HG to 0 Vacuum AS108307 56.30 AS92120 108.0030"HG to 0-15psi Compound AS108308 56.30 AS92121 108.0030"HG to 0-100psi Compound AS108309 56.30 AS92102 108.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

Model 1008 Features• Welded stainless steel socket

and tube design• Soldered brass socket and

bronze tube design• Economical corrosion resistant

stainless steel case• Dual scale dial in psi

and kPa• 1-year warranty

MODEL 1009 SPECIFICATIONS (DRY) (Liquid filled optional)Accuracy 1% full scale grade A1Dial Sizes 21⁄2" and 31⁄2"stainless steelConnection Standard: 1⁄4" NPT lower mount

Optional: 1⁄4" NPT center backBourdon Tube and AISI 316 stainless steelSocket Material Optional: bronze tube, brass socketWindow Polycarbonate

MODEL 1008 SPECIFICATIONS (LIQUID FILLED) (Dry optional)Accuracy ± 3 - 2 - 3% full scaleDial Sizes 21⁄2"and 4" Stainless SteelConnection Standard: 1⁄4" NPT lower mount

Optional: 1⁄4" back mount, and 1⁄2" NPT on 4" L.M.Bourdon Tube and AISI 316 stainless steelSocket Material Optional : Bronze tube Brass socketWindow Polycarbonate

Dry & Liquid Filled Stainless Steel Pressure GaugesModel 1009 Features• Welded stainless steel socket

and tube• Overload and underload

stops• Adjustable pointer• 5-year warranty

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

704

Low Pressure Bellows Gauge1188 Grade A (2-1-2% F.S.)

TABLE B – BELLOWS SYSTEM/RANGE SELECTION(1)

Order Bellows Pressure Vacuum Compound NPT Available

Code & Socket Range Range Range Conn.(2) Case SizeMaterial and Type

10˝ H2O to 5˝ H2O vac. & 5˝ 41⁄2˝, 6˝, 81⁄2˝ 1187A Brass 10˝ H2O to 10 psi 20˝ mercury H2O press. to 10˝ 1⁄4 41⁄2˝ 1188

mercury vac. & 5 psi 41⁄2˝, 6˝, 81⁄2˝ 1189

10˝ H2O to 5˝ H2O vac. & 5˝ 41⁄2˝, 6˝, 81⁄2˝ 1187S 316SS 10˝ H2O to 10 psi 20˝ mercury H2O press. to 10˝ 1⁄4 41⁄2˝, 1188

mercury vac. & 5 psi 41⁄2˝, 6˝, 81⁄2˝ 1189

10˝ H2O to 5˝ H2O vac. & 5˝ 41⁄2˝, 6˝, 81⁄2˝ 1187P Monel 10˝ H2O to 10 psi 20˝ mercury H2O press. to 10˝ 1⁄4 41⁄2˝ 1188

mercury vac. & 5 psi 41⁄2˝, 6˝, 81⁄2˝ 1189(1) For selection of the correct bellows system material, please inquire for the media application table.(2) Optional connection 1⁄2 NPT.(3) Others ranges available: Consult factory.

TO ORDER THE 1188 LOW PRESSURE BELLOWS GAUGES CONFIGURE BELOW AND CALL FOR PRICING:

Select: 45 1188 AS 02L XXX 10 psi

1. Dial size–41⁄2˝2. Case type–11873. Tube and socket material/solid front4. Connection size–1⁄4 (02) 5. Connection location–Lower (L) , Back (B)6. Optional features7. Standard pressure range –10 psi

With ranges as low as 10 inches ofwater vacuum, a variety of wettedparts and case materials and solidfront case designs, these low pressuregauges are generally used on applica-tions measuring air, liquid or gas.

Considerations for Selecting Low PressureBellows Type Gauges Include: Process Media: The 1188 series of pressuregauges are available with bronze, 316 stainlesssteel and Monel bellows materials. Socket mate-rials include brass, 316 stainless steel andMonel.Pressure Gauge Range: These gauges areoffered with ranges from 10 inches of water vac-uum thru 10 psi including compound ranges.Operating Environment: Depending on themodel number, these gauges are available withan aluminum or phenolic case.Accuracy Requirements: These gauges areoffered with a 2-1-2% ASME Grade A accurracy.Dial Size: Available in 41⁄2˝ thru 81⁄2˝ dial sizesdepending on the type number.Connections: 1⁄4 or 1⁄2 NPT lower or back con-nections are available depending on the typenumber. JIS, BSP, DIN and SAE connections arealso available.Mounting Requirements: Stem, surface orflush mounting, depending on the type number.

STANDARD RANGES

Double Arc

Pressure RangeDial Graduations

Inner Scale Outer Scale Range Dial GraduationsInner Outer Dial Arc Figure Minor Figure Minor Compound Dial Arc Figure MinorScale Scale (degrees) Interval Graduation Interval Graduation (Vac./Pres.) (degrees) Interval Graduation

in.H20 oz/in2 in.H20 in.H200/10 0/60 180 1 0.5 1 0.25 5/0/5 180 1 0.20/15 0/90 180 3 0.5 1 0.25 10/0/10 180 2 0.50/20 0/12 180 2 1 1 0.25 30/0/10 270 5 10/30 0/18 216 5 1 1 0.5 20/0/20 270 5 0.50/40 0/24 270 5 1 3 0.5 40/0/20 270 5 10/60 0/35 270 5 1 5 1 10/0/30 270 5 10/80 0/45 270 10 1 5 1 30/0/30 270 10 10/100 0/57 270 10 1 5 1 70/0/30 270 10 10/150 0/90 270 25 1 10 2 20/0/40 270 10 1psi in./Hg 50/0/50 270 10 10/5 0/10 270 1 0.25 1 0.5 in./Hg/psi in.Hg psi in.Hg psi0/8 0/16 270 1 0.25 2 0.5 5/0/3 270 1 1 0.2 0.10/10 0/20 270 1 0.25 2 0.5 2/0/5 270 1 1 0.1 0.1

Vacuum 5/0/5 270 1 1 0.2 0.1in.H20 mm/Hg 10/0/50 270 2 1 0.2 0.110/0 18/0 180 1 0.5 5 115/0 28/0 180 3 0.5 3 120/0 37/0 180 2 1 5 130/0 56/0 216 5 1 5 140/0 75/0 270 5 1 10 260/0 110/0 270 5 1 10 280/0 150/0 270 10 1 20 5

100/0 180/0 270 10 1 20 5150/0 270/0 270 25 1 20 5in.Hg ft H/2010/0 11/0 270 1 0.5 1 515/0 17/0 270 1 0.5 2 520/0 23/0 270 2 0.5 2 1

TABLE A – CASE SELECTION AND MOUNTING

Dial(1) Order Case Case: Material Ring: Material Mounting ConnectionSize Code Type Finish Finish

(inches) Style

41⁄2˝ (45) 1188 Phenolic Threaded Stem Lower or BackBlack Polypropylene Surface Lower or Back

Flush Back, order 1278MMounting Ring X56

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it



H

Industrial Pressure Gauge 4 1⁄2" Dial

SPECIFICATIONSAccuracy Grade 2A ± 0.5% full scaleDial Type 1279Size 41⁄2" (only)Connection 1⁄2" NPT lower mount standard

optional 1⁄4" NPT availableBourdon VAC-1000PSI Grade A Tube Phosphor bronze,Material 2000-20,000psi

AISI 316 stainless steelSocket VAC-1000psi brass;Material 2000-20,000psi

AISI 316 stainless steelCase Phenol blackRing Threaded reinforced

polypropylene

MinorCatalog No. Model Range Graduations PriceAS1200401 1279 0 to 15 psi 0.1 $119.00AS1200402 1279 0 to 30 psi 0.2 119.00AS1200403 1279 0 to 60 psi 0.5 114.00AS1200404 1279 0 to 100 psi 1 114.00AS1200405 1279 0 to 160 psi 1 114.00AS1200406 1279 0 to 200 psi 2 114.00AS1200407 1279 0 to 300 psi 2 114.00AS1200408 1279 0 to 400 psi 5 114.00AS1200409 1279 0 to 600 psi 5 114.00AS1200410 1279 0 to 800 psi 10 114.00AS1200411 1279 0 to 1000 psi 10 114.00AS1200412 1279 0 to 2000 psi 20 223.00AS1200413 1279 0 to 5000 psi 50 223.00AS1200416 1279 0 to 30"Hg VAC 0.2 119.00AS1200417 1279 30"Hg to 15 psi 0.2-0 119.00AS1200418 1279 30"Hg to 60 psi 0.2-0.5 119.00AS1200419 1279 30"Hg to 100 psi 0.2-1 119.00

Available in metric scales, in Kg/cm2, bar, or KPaNISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

• Weather-proof construction• Pressure relief back• Standard stainless steel rotary geared Teflon® movement

• Easily adjustable, self locking micrometer pointer

The Duragauge® Pressure Gaugeis the finest production gauge on themarket for industrial use where aprecise indications are required. Theline offers a wide variety of casestyles, Bourdon tubes, and pressureranges to meet any conceivable ap-plication.

The solid front phenolic casegauge is truly an industry first.Offered in 41⁄2" size only, weather-proof, hermetically sealed or liquidfilled versions. Molded threads atthe front and rear of the case pro-vide axial seals with the use ofthreaded rings.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

706

3" Pocket Test Gauges• Stainless steel construction• Zero adjustable Mylar/alu-

minum composite dial withpolished mirror band

• ± 0.5% accuracy, ASMEB40.1 Grade 2A

• 12 pressure and vacuumranges

• Black, adjustable pointer withred-painted knife-edge tip

SPECIFICATIONSAccuracy %/Grade ± 0.5/ASME B40.1

Grade 2ADial Size 3"Tube and Socket 316 Stainless Steel Material WeldedCase Material Polished Stainless

Steel, Open frontMovement Precision, stainless

steel with Teflon. “S”coated bearings andpinion

Mounting and 1⁄4 " NPT, lower onlyConnection LocationRanges Vacuum through

1000psiRing Bayonet Cam-Lock

Polished St. StWindow PolycarbonatePointer Black aluminum with

red-painted knife-edgetip

Dial Zero adjustable,Mylar/aluminum composite, white background,black numerals with polished mirror bandOptional polished stainless steel protectivecover available. See ordering information

Type 1084 Graduations

Minor Catalog Pressure Figure GraduationsNo. Range (psi) Interval Interval PriceAS10841 0/15 1 0.1 $136.00AS10842 0/30 2 0.2 136.00AS10843 0/60 5 0.5 136.00AS10844 0/100 10 0.5 136.00AS10845 0/150 10 1 136.00AS10846 0/200 20 1 136.00AS10847 0/300 20 2 136.00AS10848 0/400 50 2 136.00AS10849 0/600 50 5 136.00AS10851 0/1000 100 5 136.00

Options

Catalog No. Model DescriptionAS10852 3020198-01 Polished Stainless Steel Protective Cover 13.40NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

The Pocket Test Gauge is durable, transportableand easy to read. The case, ring, bourbon tube,socket and movement are constructed entirely ofstainless steel. The precision stainless steel move-ment, bearings and pinion are coated with Teflon“S” for reduced friction and wear.

The new white dial can be read easily and quick-ly. Each gauge has a black pointer with a red paint-ed knife-edge tip. Reading error, caused by paral-lax, is eliminated by aligning the knife-edge tip

pointer with its reflection in the mirror band on thedial.

As a standard feature, the pocket test gauge willbe supplied in an attractive cushioned Nylon fabricpouch with carrying strap.

Also available is a stainless steel cover that fitssecurely over the window and protects the gaugefrom damage while being carried in a tool box orpocket.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Standard Pressure GaugesOur Standard Pressure Gauges are designed for

long and reliable service under rugged conditions.Some typical applications are for pumps, hydraulicand pneumatic systems, compressors, and many moreapplications where liquid and gases do not corrodebrass. The accuracy of the gauges is 1.5% of full scalein all sizes and they are available from 30 psi to 5000psi. Vacuum ranges and compound ranges areavailable upon request.

SPECIFICATIONSAccuracy 1⁄5% of full scaleCase Black drawn steel caseBourdon Tube Copper alloy, coiled safety bourdon tube for

800 psi and higher Window Acrylic, snap inMovement Brass with bearing surfaces highly finished Temperature Range Ambient 10° to 150°FDuty Range A gauge range of twice the working pressure is

generally selected. Working pressure should be limited to 75% of gauge range

Catalog Range Size Connection Acc. Conn. PriceNo. Size

WK333134 0 to 30 psi 1.5"-111.10 Center Back Mount 1.5% 1⁄8" $19.00WK333135 0 to 60 psi 1.5"-111.10 Center Back Mount 1.5% 1⁄8" 19.00WK333136 0 to 100 psi 1.5"-111.10 Center Back Mount 1.5% 1⁄8" 19.00WK333137 0 to 160 psi 1.5"-111.10 Center Back Mount 1.5% 1⁄8" 19.00WK333138 0 to 200 psi 1.5"-111.10 Center Back Mount 1.5% 1⁄8" 19.00WK333139 0 to 30 psi 2"-111.10 Center Back Mount 1.5% 1⁄4" 19.00WK333140 0 to 60 psi 2"-111.10 Center Back Mount 1.5% 1⁄4" 19.00WK333141 0 to 100 psi 2"-111.10 Center Back Mount 1.5% 1⁄4" 20.23WK333142 0 to 160 psi 2"-111.10 Center Back Mount 1.5% 1⁄4" 19.00WK333144 0 to 30 psi 2.5"-111.10 Lower Mount 1.5% 1⁄4" 20.40WK333145 0 to 60 psi 2.5"-111.10 Lower Mount 1.5% 1⁄4" 20.40WK333146 0 to 100 psi 2.5"-111.10 Lower Mount 1.5% 1⁄4" 20.40WK333147 0 to 160 psi 2.5"-111.10 Lower Mount 1.5% 1⁄4" 20.40WK333148 0 to 200 psi 2.5"-111.10 Lower Mount 1.5% 1⁄4" 20.75WK333149 0 to 300 psi 2.5"-111.10 Lower Mount 1.5% 1⁄4" 20.40NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

(Please allow 4 weeks for delivery on center back mount gauges)

NIST it

Liquid Filled Hydraulic Pressure Gauges NIST it

21⁄2" Model 3000 Stainless SteelRange Catalog No. Price0-15psi AS300401 $42.000-30psi AS300402 42.000-60psi AS300403 42.000-100psi AS300404 42.000-200psi AS300405 42.000-600psi AS300408 42.000-1000psi AS300409 48.000-2000psi AS300410 48.000-4000psi AS300411 48.000-5000psi AS300412 48.000-6000psi AS300413 48.00Vacuum 30"Hg-0 AS300417 43.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

SPECIFICATIONSAccuracy ± 3 - 2 - 3% full scaleDial Size 21⁄2"Connection 1⁄4" NPT Lower mount, (Optional back mount)Socket Brass, with O-ring case sealLiquid Glycerin 0°-150°FWindow 3005HL Glass

3005PHL AcrylicCase 3005HL Stainless steel with vent plug

3005PHL ABS case with vent plug


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

708

Industrial Stainless Steel Gauges

Catalog No. Ramge Connection* Connection Size Dial Size PriceWK9744827 30” Hg Lower Mount 1/4” NPT 2.5” $56.15WK9744894 0 - 15 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744908 0 - 30 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744916 0 - 60 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744924 0 - 100 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744932 0 - 160 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744940 0 - 200 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744959 0 - 300 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744967 0 - 400 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744975 0 - 600 psi Lower Mount 1/4” NPT 2.5” 53.43WK9744991 0 – 1000 psi Lower Mount 1/4” NPT 2.5” 53.43WK9745009 0 – 1500 psi Lower Mount 1/4” NPT 2.5” 58.42WK9745017 0 – 2000 psi Lower Mount 1/4” NPT 2.5” 58.42WK9745025 0 – 3000 psi Lower Mount 1/4” NPT 2.5” 58.42WK9745033 0 – 5000 psi Lower Mount 1/4” NPT 2.5” 58.42WK9745041 0 – 10000 psi Lower Mount 1/4” NPT 2.5” 58.42NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 85.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 130.00* Center Back Mount Connection Available** 4” Dial Size Available

SPECIFICATIONSSizes 2 1/2” (63 mm), 4” (100 mm)Case 304 SSBayonet Ring Polished SSWetted Parts 316 SSWindow Safety glassDial White aluminumPointer Black, adjustableO-ring EPDM (4” only)Accuracy ± 1.5% of span (2 1/2”),

± 1.0% of span (4”)ASME B40.1 Grade 1A

Type 232.54 gauge features 316 stainless steelwetted parts and 304 stainless steel case and bay-onet ring, an adjustable pointer, a laminated safe-ty glass window, and can be liquid-filled in thefield (233.54).

WIKA stainless steel gauges are ideal forprocess, chemical, and petrochemical applications,oil exploration and production, power generation,pollution control equipment, and any other appli-cation requiring fine quality, long lasting pressuremeasurement instrumentation.

NIST it



H

Industrial Stainless Steel Gauges

Catalog No. Range Connection* Connection Size Dial SIze** PriceWK9767002 30 “Hg Lower Mount 1/4” NPT 2.5” 28.37WK9767037 0 - 15 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767045 0 - 30 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767053 0 - 60 psi Lower Mount 1/4” NPT 2.5" 27.32WK9767061 0 - 100 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767070 0 - 160 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767088 0 - 200 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767096 0 - 300 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767100 0 - 400 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767118 0 - 600 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767126 0 – 1000 psi Lower Mount 1/4” NPT 2.5” 27.32WK9767134 0 – 1500 psi Lower Mount 1/4” NPT 2.5” 30.25WK9767142 0 – 2000 psi Lower Mount 1/4” NPT 2.5” 30.25WK9767150 0 – 3000 psi Lower Mount 1/4” NPT 2.5” 30.25WK9767169 0 – 5000 psi Lower Mount 1/4” NPT 2.5” 30.25WK9767177 0 – 10000 psi Lower Mount 1/4” NPT 2.5” 39.29

AccessoriesNISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 85.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 130.00* Center Back Mount Connection Available** 4” Dial Size Available

SPECIFICATIONSSize 2 1/2” (63 mm)Case Stainless steelRing Polished SS, crimpedWetted Parts Copper alloyWindow Polycarbonate (2 1/2”), Acrylic (4”)Dial ABSPointer Black aluminumFilling GlycerineO-ring EPDMAccuracy + 1.5% of span

WIKA Type 213.53 gauges feature a stain-less steel case for protection in harsh environ-ments. These gauges are supplied standardwith a glycerine filled case.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

710

Contractor Gauges

Catalog No. Range Connection Connection Size PriceWK4277750 0 - 15 psi Lower Mount 1/4” NPT $41.45WK4277768 0 - 30 psi Lower Mount 1/4” NPT 41.45WK4277776 0 - 60 psi Lower Mount 1/4” NPT 41.45WK4277784 0 - 100 psi Lower Mount 1/4” NPT 41.45WK4277792 0 - 160 psi Lower Mount 1/4” NPT 41.45WK4277806 0 - 200 psi Lower Mount 1/4” NPT 41.45WK4277814 0 - 300 psi Lower Mount 1/4” NPT 41.45WK4277822 0 - 400 psi Lower Mount 1/4” NPT 41.45WK4277831 0 - 600 psi Lower Mount 1/4” NPT 41.45

AccessoriesNISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 127.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 195.00

SPECIFICATIONSSize 4 1/2” (115 mm)Wetted Parts Copper alloyCase Stainless steel, matte finishWindow Snap-in acrylicDial White aluminumPointer Black aluminum, adjustableAccuracy ± 1% of span

NIST it

WIKA Type 111.25 4 1/2” gauges are specificallydesigned for the HVAC market as a contractor’sgauge. This gauge features a stainless steel caseand bayonet ring, brass wetted parts, and an ad-justable pointer. The standard accuracy is ± 1.0%of span with both single scale and dual scalePSI/KPA.



H

Commercial Gauges

Catalog No. Range Connection Connection Size PriceWK4252901 30” Hg Lower Mount 1/4” NPT $21.54WK4252919 0 - 15 psi Lower Mount 1/4” NPT 18.65WK4252927 0 - 30 psi Lower Mount 1/4” NPT 18.65WK4252935 0 - 60 psi Lower Mount 1/4” NPT 18.65WK4252943 0 - 100 psi Lower Mount 1/4” NPT 18.65WK4252951 0 - 160 psi Lower Mount 1/4” NPT 18.65WK4252960 0 - 200 psi Lower Mount 1/4” NPT 18.65WK4252978 0 - 300 psi Lower Mount 1/4” NPT 18.65WK4252986 0 - 400 psi Lower Mount 1/4” NPT 18.65WK4252994 0 - 600 psi Lower Mount 1/4” NPT 18.65


SPECIFICATIONSSize 2” (50 mm)Wetted Parts Copper alloyCase Black ABSWindow Snap-in acrylicDial White ABSPointer Black ABSAccuracy ± 3% of span

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

712

Low Pressure Gauges

Catalog No. Range Connect Connection Size Dial Size PriceWK9852344 0-30 “H2O/mm H2O vacuum Lower Mount 1/4” NPT 2.5” $38.45WK9748321 0-60 “H2O/mm H2O vacuum Lower Mount 1/4” NPT 2.5” 38.45WK9747473 0-100 “H2O/mm H2O vacuum Lower Mount 1/4” NPT 2.5” 38.45WK9851682 0-15 “H2O/mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851690 0-30 “H2O/mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851704 0-60 “H2O/mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851810 0-100 “H2O/mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851828 0-200 “H2O/mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851771 0-10oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851780 0-15oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851798 0-20oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851747 0-30oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851801 0-35oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851755 0-60oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851720 0-20oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45WK9851739 0-32oz./sq. in./mm H2O Pressure Lower Mount 1/4” NPT 2.5” 38.45

AccessoriesNISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 127.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 195.00* 4” Dial Size Available (612.20)

SPECIFICATIONSSize 2 1/2” (63mm)Case Black painted steelWetted Parts Copper alloyWindow AcrylicDial White aluminumPointer Black aluminumAccuracy + 1.5% of span

WIKA Type 611.10 low pressure gauges are ex-tremely sensitive and highly accurate. The copperalloy capsule is designed to measure pressure andvacuum of gaseous media from as low as 15”H2Oto 240” H2O (10 psi). An adjustment screw is lo-cated on the dial to re-zero the pointer if neces-sary. The finely polished nickel silver pinion gearand shaft of the movement ensure repeatable accuracy.

NIST it



H

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Precision 4” Test Gauges

Catalog No. Range Connection Connection Size PriceWK4220013 30” Hg Lower Mount 1/4” NPT $149.36WK4220021 0 - 15 psi Lower Mount 1/4” NPT 149.36WK4220030 0 - 30 psi Lower Mount 1/4” NPT 149.36WK4220048 0 - 60 psi Lower Mount 1/4” NPT 149.36WK4220056 0 - 100 psi Lower Mount 1/4” NPT 149.36WK4220064 0 - 160 psi Lower Mount 1/4” NPT 149.36WK4220072 0 - 200 psi Lower Mount 1/4” NPT 149.36WK4220081 0 - 300 psi Lower Mount 1/4” NPT 149.36WK4220099 0 - 400 psi Lower Mount 1/4” NPT 149.36WK4220102 0 - 600 psi Lower Mount 1/4” NPT 149.36


SPECIFICATIONSSize 4” (100 mm)Case 304 SSBayonet Ring Polished SSWetted Parts 316 SSWindow Safety glassDial White aluminum with mirrored bandPointer Black, adjustableO-ring EPDMAccuracy ± 0.25% of span (ASME B40.1 Grade 3A)

Ranges 0/30” Hg Vac through 0/600 psi0.25% of span (ASME B40.1 Grade 3A)Ranges 0/2000 psi through 0/20,000 psi0.25% of span (ASME B40.1 Grade 3A)

WIKA Type 332.54 inspector’stest gauges are convenient for fieldcalibrations. They have an accura-cy of ±0.25% which meets ASMEB40.1 Grade 3A. The mirroredband on the dial and the knife-edgepointer make it easy to take accu-rate readings from the gauge. Type332.54 test gauges are suppliedstandard with a zippered, nyloncarrying pouch.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

714


Catalog No. Range Connection Connection Size PriceWK9746859 30” Hg Lower Mount 1/4” NPT $471.51WK9746867 0 - 15 psi Lower Mount 1/4” NPT 352.58WK9746875 0 - 30 psi Lower Mount 1/4” NPT 352.58WK9746884 0 - 60 psi Lower Mount 1/4” NPT 352.58WK9746892 0 - 100 psi Lower Mount 1/4” NPT 352.58WK9746905 0 - 160 psi Lower Mount 1/4” NPT 352.58WK9746914 0 - 200 psi Lower Mount 1/4” NPT 352.58WK9746922 0 - 300 psi Lower Mount 1/4” NPT 352.58WK9746930 0 - 400 psi Lower Mount 1/4” NPT 352.58WK9746948 0 - 600 psi Lower Mount 1/4” NPT 352.58WK9746965 0 – 1000 psi Lower Mount 1/4” NPT 352.58WK9746973 0 – 1500 psi Lower Mount 1/4” NPT 401.48WK9746981 0 – 2000 psi Lower Mount 1/4” NPT 401.48WK9746999 0 – 3000 psi Lower Mount 1/4” NPT 401.48WK9747006 0 – 5000 psi Lower Mount 1/4” NPT 401.48WK9747015 0 – 10000 psi Lower Mount 1/4” NPT 401.48NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 127.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 195.00Note: 1/2" NPT Connections Available

SPECIFICATIONSSize 6” (160 mm)Case Stainless steelBayonet Ring Stainless steelWetted Parts Copper alloyMovement Brass with nickel-silver pinion gears and shaftWindow Laminated safety glassDial White aluminum with mirrored bandPointer Black aluminum, knife-edgeAccuracy ± 0.25% of span

ASME B40.1 Grade 3A

Extremely sensitive and highly ac-curate, WIKA Type 312.20 testgauges are excellent for instrumentshops, gauge repair and calibrationshops, testing laboratories and otherapplications demanding high preci-sion and consistent results. Type312.20 test gauges feature adjustableknife-edge pointers and mirror bandson the dial to assure precise readingsand to eliminate parallax error.Inside, a low-friction, wear resistantmovement made of nickel-silver(Type 312.20) delivers a long servicelife, and consistent levels of accuracy.

NIST it



H

Process Gauges

Catalog No. Range Connection Connection Size PriceWK9834036 30” Hg Lower Mount 1/4” NPT $74.33WK9834117 0 - 15 psi Lower Mount 1/4” NPT 74.33WK9834125 0 - 30 psi Lower Mount 1/4” NPT 74.33WK9834133 0 - 60 psi Lower Mount 1/4” NPT 74.33WK9834141 0 - 100 psi Lower Mount 1/4” NPT 74.33WK9834150 0 - 160 psi Lower Mount 1/4” NPT 74.33WK9834168 0 - 200 psi Lower Mount 1/4” NPT 74.33WK9834176 0 - 300 psi Lower Mount 1/4” NPT 74.33WK9834184 0 - 400 psi Lower Mount 1/4” NPT 74.33WK9834192 0 - 600 psi Lower Mount 1/4” NPT 74.33WK9834206 0 – 1000 psi Lower Mount 1/4” NPT 74.33AccessoriesNISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 127.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 195.00

SPECIFICATIONSSize 4 1/2” (115 mm)Case & Ring Fiberglass reinforced thermoplastic, blackWindow AcrylicDial White aluminumPointer Aluminum, adjustableAccuracy ± 0.5% of span

ASME B40.1 Grade 2A

Specifically designed for the chemicaland petroleum processing industries,WIKA process gauges have the construc-tion, materials, and engineering it takesto stand up to the toughest conditionsaround. The 212.34 gauges are equippedwith brass-wetted parts. It is engineeredto deliver years of accurate service whilewithstanding vibration and a wide rangeof temperatures.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

716

41⁄2" Process Gauges

Catalog No. Range Connection Connection Size Dial Size PriceWK9834729 30” Hg Lower Mount 1/2” NPT 4.5” $84.58WK9834800 0 - 15 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834818 0 - 30 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834826 0 - 60 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834834 0 - 100 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834842 0 - 160 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834850 0 - 200 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834869 0 - 300 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834877 0 - 400 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834885 0 - 600 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834893 0 – 1000 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834907 0 – 1500 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834915 0 – 2000 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834923 0 – 3000 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834931 0 – 5000 psi Lower Mount 1/2” NPT 4.5” 84.58WK9834940 0 – 10000 psi Lower Mount 1/2” NPT 4.5” 84.58

AccessoriesNISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 127.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 195.00* Lower Back Mount Connections Available

SPECIFICATIONSSize 4 1/2” Case & Ring Fiberglass reinforced thermoplastic, blackWindow AcrylicDial White aluminumPointer Aluminum, adjustableAccuracy ± 0.5% of span

ASME B40.1 Grade 2A

Specifically designed for the chemicaland petroleum processing industries,WIKA process gauges have the construc-tion, materials, and engineering it takes tostand up to the toughest conditions around.The 232.34 gauges are equipped with stain-less steel wetted parts. It is engineered todeliver years of accurate service while with-standing vibration, corrosive media andcorrosive environments, and a wide rangeof temperatures. The WIKA Type 232.34 6”process gauge provides excellent visibilitywith a 6” dial.

NIST it



H

Weatherproof Pressure Gauges 41⁄2" & 6" Dials

Dial Sizes 4 1⁄2" 6"

Range Minor Graduation Catalog No. Price Catalog No. Price

Pressure: PSI0—15 0.1 AS137901 $149.00 AS137921 $240.000—30 0.2 AS137902 149.00 AS137922 240.000—60 0.5 AS137903 144.00 AS137923 231.000—100 1 AS137904 144.00 AS137924 231.000—200 1 AS137905 144.00 AS137925 231.000—400 5 AS137906 144.00 AS137926 231.000—800 10 AS137908 144.00 AS137928 231.000—2000 20 AS137910 242.00 AS137930 349.000—5000 50 AS137911 242.00 AS137931 349.00

Vacuum30"Hg to 0 0.2 AS137914 149.00 AS137934 240.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

Scales available in metric indication; Kpa, Bar, Kg/cm2

Model 1377

SPECIFICATIONSAccuracy Grade 2A ± 0.5% full scaleDial 41⁄2" and 6” diametersConnection 1⁄4" NPT male back connection (standard)

Optional 1⁄2" NPT male back connectionBourdon Tube Vacuum 1000psi Grade A phosphor bronzeMaterial 2000-20,000psi (316 stainless steel available)Socket Vacuum through 1000psi brass, 1000-20,000psiMaterial (316 stainless steel available)Case Solid front aluminum black epoxy coatedRing Hinged steel black enamel coated

• ± 0.5% full scale accuracy• Weatherproof case• Standard stainless steel rotary

geared movement• Easily adjustable, self locking

micrometer pointer• 100 standard psi and metric ranges,

5 standard systems

Designed for flush mounting, this solid frontgauge is ideal for panel board applications. Itsblack epoxy coating and its tough aluminumweatherproof case easily allows application in avariety of climatic conditions.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

718

Dial Sizes 41⁄2" 6" 8 1⁄2"Minor Minor Minor

Range Catalog No. Price Graduation Catalog No. Price Graduation Catalog No. Price Graduation

Pressure PSI0-15 AS800240 $226.00 0.05 AS800260 $271.00 0.05 AS800280 $529.00 0.020-30 AS800241 226.00 0.1 AS800261 271.00 0.1 AS800281 529.00 0.050-60 AS800242 226.00 0.2 AS800262 271.00 0.2 AS800282 529.00 0.10-100 AS800243 226.00 0.5 AS800263 271.00 0.2 —

0-200 AS800244 226.00 0.5 AS800264 271.00 0.5 —

0-400 AS800245 226.00 1 AS800265 271.00 1 —

0-600 AS800246 317.00 2 AS800267 391.00 2 AS800286 604.00 10-1000 AS800248 317.00 5 AS800269 391.00 2 AS800288 604.00 20-2000 AS800249 317.00 10 — —

0-5000 AS800250 317.00 20 AS800271 391.00 10 —

0-10,000 AS800251 317.00 50 AS800272 391.00 20 —

Vacuum30"HG to 0 AS800252 226.00 0.1 AS800273 271.00 0.1 —

CompoundHg/PSI Vac Pres Vac Pres30/0/15 AS800253 226.00 0.2 0.1 AS800274 271.00 0.2 0.1 —

30/0/30 AS800254 226.00 0.5 0.2 AS800275 271.00 0.2 0.1 —

30/0/100 AS800255 226.00 1 0.5 AS800276 271.00 0.5 0.5 —

NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

Precision Test Gauge ±0.25% Accuracy

MODEL 1082 SPECIFICATIONSAccuracy %/Grade ± 0.25%/ANSI B 40.1, Grade 3ADial Size 41⁄2", 6", 81⁄2"Standard Bourdon Vac thru 400psi: phosphor bronzeTube Material Vac to 10,000psi: K-MonelSocket Material Vac to 400psi: brass

Vac to 10,000psi: Monel 400Window GlassCase Aluminum, solid front, black epoxy coatedMaterialAluminum White coated, black numeralsDial with polished mirror bandStandard 1⁄4" Optional back connection availableLower MountConnection

This new generation of test gauges to meet the exactingneeds of instrument engineers and quality specialists. Thenew Ashcroft® test gauge can be used as a transfer standardfor periodically checking the accuracy of pressure instru-

ments or as a laboratory instrument for research and testlabs. The wealth of new features makes it an excellent testgauge for process applications where high accuracy in pres-sure measurement is essential.

• Precision accuracy ± 0.25% full scale, ASME Grade 3A• Temperature compensated—reduces ambient temperature errors

to less than 0.005% per °F • External micro-span adjustment for ease in span calibration from

0-100% of scale• Hydraulically staked movement with Teflon® coated gears and

bearings improves stability• Precision dial and pointer results in excellent readability

NIST it



H

• High accuracy 0.1% of span• Repeatability 0.02% of span• Hysteresis 0.1% of span

(or less)• Sensitivity 0.1% of span• 5-year warranty

SPECIFICATIONSAccuracy 0.1% of span This accuracy statement includes repeatability, linearity and hysteresis, obtained by calibration with pressure standards

traceable to N.I.S.T.Calibration Points 12 points up scale and 12 down scaleOverpressure 120% of span without calibration shift 200% of span without damageRepeatability 0.02% of spanHysteresis .1% span or lessMeasure and Fluid gauges are calibrated with air (up to 1,000 psi) or distilled water (up to 10,000 psi). Other fluids compatible with Ni Span C, 300

series stainless steel and Buna-N may be used. Gauges may be oxygen cleanedNeedle Movement 310°Temperature 25°F (-32°C) to 125°F (+ 52°C)

Precision Test Gauges

Pressure Minor Catalog 7" Dial Size Price Catalog 8.5" Dial Size Price Catalog 12" Dial Size PriceRange Graduations No No. No.15 .02 TD7000 25519-15-E51 $1,250.00 TD8500 25516-15-E21 $1,385.00 TD1200 25517-15-E21 $1,540.00

30 .05 TD7001 25519-21-E51 1,250.00 TD8501 25516-21-E21 1,385.00 TD1201 25517-21-E21 1,540.00

60 0.1 TD7002 25519-22-E51 1,250.00 TD8502 25516-22-E21 1,385.00 TD1202 25517-22-E21 1,540.00

100 0.1 TD7003 25519-23-E51 1,150.00 TD8503 25516-23-E21 1,285.00 TD1203 25517-23-E21 1,540.00

150 0.2 TD7004 25519-24-E51 1,150.00 TD8504 25516-24-E21 1,285.00 TD1204 25517-24-E21 1,540.00

200 0.2 TD7005 25519-25-E51 1,150.00 TD8505 25516-25-E21 1,285.00 TD1205 25517-25-E21 1,440.00

500 0.5 TD7008 25519-27-E51 1,150.00 TD8508 25516-27-E21 1,285.00 TD1208 25517-27-E21 1,440.00

800 1.0 TD7010 25519-53-E51 1,150.00 TD8510 25516-53-E21 1,285.00 TD1210 25517-53-E21 1,440.00

1000 1.0 TD7011 25519-29-E51 1,150.00 TD8511 25516-29-E21 1,285.00 TD1211 25517-29-E21 1,440.00

1500 2.0 TD7012 25519-31-E51 1,220.00 TD8512 25516-31-E21 1,355.00 TD1212 25517-31-E21 1,510.00

2000 2.0 TD7013 25519-32-E51 1,220.00 TD8513 25516-32-E21 1,355.00 TD1213 25517-32-E21 1,510.00

3000 5.0 TD7014 25519-33-E51 1,220.00 TD8514 25516-33-E21 1,355.00 TD1214 25517-33-E21 1,510.00

5000 5.0 TD7016 25519-35-E51 1,220.00 TD8516 25516-35-E21 1,355.00 TD1216 25517-35-E21 1,510.00

8000 10 TD7018 25519-37-E51 1,220.00 TD8518 25516-37-E21 1,355.00 TD1218 25517-37-E21 1,510.00

10,000 10 TD7019 25519-38-E51 1,220.00 TD8519 25516-38-E21 1,355.00 TD1219 25517-38-E21 1,510.00

15 PSIV .02 TD7020 2521X9-15-E51 1,365.00 TD8520 2521X6-15-E21 1,500.00 TD1220 2521X7-15-E21 1,655.00

30" VAC .05 TD7021 2521X9-21-E51 1,365.00 TD8521 2521X6-21-E21 1,500.00 TD1221 2521X7-21-E21 1,655.00

800 mmHg 1.0 TD7022 2521X9-ISB-E51 1,365.00 TD8522 2521X6-ISB-E21 1,500.00 TD1222 2521X7-ISB-E21 1,655.00

15 PSIA .02 TD7023 25519-15-E51EBQ 1,365.00 TD8523 25516-15-E51EBQ 1,500.00 TD1223 25517-15-E51EBQ 1,655.00

30/30 TD7024 2511X9-21E21-E51 1,365.00 TD8524 2511X6-21E21-E21 1,500.00 TD1224 2511X7-21E21-E21 1,655.00




NISTPR5 NIST Traceable Certificate $85.00


NIST it

Features high accuracy of 0.1% of span


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

720

Analog/Digital Pressure Gauge

Catalog No. Model Description PriceDW33721 7214D-G100 Digital/Analog Pressure Gauge, Range 0-100 psig $499.00DW33722 7214D-G200 Digital/Analog Pressure Gauge, Range 0-200 psig 499.00DW33723 7214D-G300 Digital/Analog Pressure Gauge, Range 0-300 psig 499.00DW33724 7214D-G600 Digital/Analog Pressure Gauge, Range 0-600 psig 499.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

• Solid front case• Direct drive movement — No cams, gears or

linkages• Small diameter tubing wound in spiral/helical coil• Overpressure stop — Prevents false (LOW) reading

while overpressure condition exists. • Center post bearing carrier. Supports pointer shaft

and coil• Rear blowout hole (covered with label)• Case and shock protection ribs help prevent damage

to bourdon tube in the event of severe Shock.• Filter plug protects the bourdon tube• High impact plastic case and lens

SPECIFICATIONSSize 6”—design conforms to ASME B40.1Accuracy ASME Grade 2A (1/2% of full scale)Pressure Connection 1/4” NPT female, duplicated back and bottomWetted Parts Inconel® X-750 Bourdon tube, 316 SS connection blockHousing Black polycarbonate case and clear acrylic coverMovement Direct drive of pointerOverpressure 150% of full scale. Normal operation between 25% and 75% of full scaleCalibration Vertical mounting standardStandard Accessory (1) 1/4” NPT plug, brass or stainless steelOptional Accessory No. A-341 Brass Adapter. 1/4” NPT x G 1/2 A (per ISO 228/1) parallel threadElectricalPower Supply 10-35 VDC, 16-26 VACWarm-Up Time 10 minutes (LCD)Current Consumption 38 mA max (DC), 76 mA max (AC)

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NISTPR5 NIST Traceable Certificate 85.00 NISTPR6 NIST Traceable Certificate with Data 130.00

No Flange; 1/4” NPT Male Bottom Connection; PSI DialDial Size 4 1/2" Dial Size 6" Dial SizeCase Color Red Yellow Red YellowRange Catalog No. Price Catalog No. Price Catalog No. Price Catalog No. Price0-30 psi D255442153 $329.00 D255442154 $329.00 D255452153 $394.00 D255452154 $394.000-60 psi D255442253 299.00 D255442254 299.00 D255452253 364.00 D255452254 364.000-100 psi D255442353 299.00 D255442354 299.00 D255452353 364.00 D255452354 364.000-300 psi D255442653 299.00 D255442654 299.00 D255452653 364.00 D255452654 364.000-500 psi D255442753 299.00 D255442754 299.00 D255452753 364.00 D255452754 364.000-1000 psi D255442953 299.00 D255442954 299.00 D255452953 364.00 D255452954 364.000-3000 psi D255443353 299.00 D255443354 299.00 D255453353 364.00 D255453354 364.000-5000 psi D255443553 299.00 D255443554 299.00 D255453553 364.00 D255453554 364.000-10,000 psi D255443853 299.00 D255443854 299.00 D255453853 364.00 D255453854 364.00Front Flange; 1/4” NPT Male Back Connection; PSI DialDial Size 4 1/2" Dial Size 6" Dial SizeCase Color Red Yellow Red YellowRange Catalog No. Price Catalog No. Price Catalog No. Price Catalog No. Price0-30 psi D255442123 $329.00 D255442124 $329.00 D255452123 $394.00 D255452124 $394.000-60 psi D255442223 299.00 D255442224 299.00 D255452223 364.00 D255452224 364.000-100 psi D255442323 299.00 D255442324 299.00 D255452323 364.00 D255452324 364.000-300 psi D255442623 299.00 D255442624 299.00 D255452623 364.00 D255452624 364.000-500 psi D255442723 299.00 D255442724 299.00 D255452723 364.00 D255452724 364.000-1000 psi D255442923 299.00 D255442924 299.00 D255452923 364.00 D255452924 364.000-3000 psi D255443323 299.00 D255443324 299.00 D255453323 364.00 D255453324 364.000-5000 psi D255443523 299.00 D255443524 299.00 D255453523 364.00 D255453524 364.000-10,000 psi D255443823 299.00 D255443824 299.00 D255453823 364.00 D255453824 364.00



H

• Helically Wound Bourdon Tubein Inconel X-750

• All Wetted Parts in 316SS orInconel

• Precision Anti-FrictionSapphire Shaft Bearings

• High Impact Resistant CycolacCase

• Needle Edged Pointer• Adjustable Zero Set-Point• One Moving Part

• No recalibration required• Longer field service life• Greater reading accuracy

• Maintenance free• Corrosion resistant• Safer operation (UL listed)

SPECIFICATIONSPressure Ranges 0-30 psig to 0-20,000 psig equivalent ISO and

Metric Scales AvailableBurst Pressure 500% of Scale Pressure*Accuracy ± 0.25% of span. No tapping required, includes all

friction, hysteresis, and linearity variations.Temperature -65°F to + 190°F (-54°C to + 88°C)Life 250,000 cycles minimum to 1,000,000, 80% of full scaleRepeatability ± 0.025% of full scale

Direct Drive Rugged Test Gauges6 Year Warranty

We've replaced the antiquated C shape Bourdon tube inour pressure gauges with a unique helically woundBourdon, The Direct Drive Difference. Our Bourdon coil iscoupled directly to the shaft-pointer, the only moving part.

Fewer parts, fewer problems. Regular calibration iseliminated because there are no complex, wear-proneparts. Linearity is built-in; no span adjustment is neces-sary-ever. And accuracy is maintained throughout the lifeof the gauge, many times longer than those old-fashioneddesigns.

The Direct Drive design gives instant response while re-sisting pointer pulsation. Overpressure? Even 150% of fullscale will not affect the accuracy of most gauges. and ittakes pressures of 500% greater than dial range to result insensing coil rupture. Even when subject to abuse, DirectDrive gauges last longer.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

722

Available in Gauge, Absolute, Vacuum, Differential and Compound ScalesSeries 1500 Gauges have capsule-type pressure ele-

ments up to and including the 150-psig range. Rangesof 200 psig and above have Bourdon tubes. The

pressure to be measured is applied to the cap-sule or Bourdon tube through a single connec-

tion in the case. The case has a tempered-glass dial cover, solid-front dial, and a

blow-out plug on the back. Readings arereferenced to atmospheric pressure inthe case.

Catalog No. Model Description PriceWT555610 1500G 81⁄2" Pressure Gauge $1,730.00

Specify Range RequiredWT555611 1500A 81⁄2" Pressure Gauge Absolute 3,430.00

Specify Range Required.WT555613 — Carrying Case 453.00WT555614 — Liquid Service Calibration 263.00

When ordering, please specify specific range required

81⁄2" High Accuracy ±0.066% Pressure Gauges

SPECIFICATIONSCase Anodized aluminum with tempered-glass dial cover; flush Construction mounted by three screws through the bezel.Zero The zero-adjusting screw is accessible through both the Adjustment front and the back of the case.Case 150 psi and below, 1⁄8" female NPT; 200 psi and above, Connections 1⁄4" female NPT. Both has a built-in stainless steel filter

and are located in the bottom of the case.Materials 150 psi and below (capsule) Ni-Span C; brass; 303 Exposed to stainless steel; soft solder; silver solder. 303 stainless Measured tubing and adapter with silver solder at the pressure Gas connection are optional instead of brass and soft solder in

the ranges up to and including 150 psi, but standard in the ranges of 200 psi and above.200 psi and above (Bourdon tube) Ni-Span C; 302, 303, and 304 stainless steel; Easy-flow #45 brazing alloy; silver solder; nylon® or TFE.

Hysteresis 0.1% of full scale for ranges of 150 psi and below; 0.2% of full scale for 200 psi and above.

Maximum 0.1% of full scale per 10°C change from 25°C.Temperature EffectMedia gases and liquids must be non-corrosive. All standard units are gas or air only.Optional Gauges with ranges 200, 300, and 500 psi (Bourdon tubes) Liquid can be calibrated for liquid service as optional. The 0-1000 Service psi range is calibrated for liquid service only.Case Cases are open to atmosphere.Pressure Bleed Tube Ranges of 200, 300, and 500 psi (Bourdon tubes), when

calibrated for liquid service, have bleed tubes to facilitate filling and flushing. On the 1000 psi range, a bleed tube is standard.

• Accuracy ± 0.066% of full scale• Excellent Repeatability ± 0.03%• Dual Revolution Dial offers 45"

needle travel• All Dials are custom printed for each

Individual mechanism• Widely spaced graduations give

excellent readability• Calibration is traceable to NIST and

MIL-STD-45662

Gauge Range Graduation0-4.5 psi 0.005 psi0-10 psi 0.01 psi0-15.5 psi 0.02 psi0-20 psi 0.02 psi0-30 psi 0.05 psi0-45 psi 0.05 psi0-60 psi 0.1 psi0-100 psi 0.01 psi0-150 psi 0.2 psi0-200 psi 0.2 psi

Gauge Range Graduation0-300 psi 0.5 psi0-500 psi 0.5 psi0-125" water 0.2"0-280" water 0.5"0-800 mm Hg 1.0 mm0-31.5" Hg 0.05"0-60" Hg 0.1"0-120 Hg 0.2"Vacuum-30" Hg to 0 0.05"

AbsoluteRange Graduation0-15.5 psia 0.02 psia0-25 psia 0.05 psia0-35 psia 0.05 psia0-50 psia 0.05 psia0-100 psia 0.1 psia0-150 psia 0.2 psia0-200 psia 0.2 psia

AbsoluteRange Graduation0-300 psia 0.5 psia0-500 psia 0.5 psia0-800 mm Hg 1.0 mm0-31.5" Hg 0.05"0-50" Hg 0.05"0-70" Hg 0.1"0-100" Hg 0.1"

NIST it



H


Catalog No. Range Connection Connection Size PriceWK9328831 0 - 30 psi Lower Mount 1/4” NPT $1,572.75WK9328840 0 - 60 psi Lower Mount 1/4” NPT 1,378.39WK9328858 0 - 100 psi Lower Mount 1/4” NPT 1,378.39WK9328866 0 - 160 psi Lower Mount 1/4” NPT 1,378.39WK9328874 0 - 100 psi Lower Mount 1/4” NPT 1,378.39WK9328882 0 - 300 psi Lower Mount 1/4” NPT 1,378.39WK9328890 0 - 400 psi Lower Mount 1/4” NPT 1,378.79WK9328904 0 - 600 psi Lower Mount 1/4” NPT 1,378.79WK9328920 0 – 1000 psi Lower Mount 1/4” NPT 1,507.61WK9328947 0 – 2000 psi Lower Mount 1/4” NPT 1,507.61WK9328955 0 – 3000 psi Lower Mount 1/4” NPT 1,507.61WK9328998 0 – 15000 psi Lower Mount 1/4” NPT 1,789.17NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00NISTPRQ5 2 Year NIST Traceable Certificate 127.00NISTPRQ6 2 Year NIST Traceable Certificate with Data 195.00

SPECIFICATIONSSize 10” (250 mm)Case Cast aluminum, dark grey with hammered finishRing Cast aluminum, dark grey with hammered finishConnection 316 stainless steelBourdon Tube Ni-Span C® Window Green tinted acrylic, non-reflectingDial White aluminum with mirrored band and zeroadjustmentPointer Black aluminum knife-edgeAccuracy ± 0.1% of span (ASME B40.1 Grade 4A) *Beryllium copper is substituted for 10 psi range.

WIKA Type 342.11 precision testgauges are high quality, time-proveninstruments designed for use as pres-sure transfer standards and in appli-cations requiring exceptional precisionand high reliability in the measure-ment of pressure. Both types of WIKAprecision test gauges feature aBourdon tube made of Ni-Span C® forall pressure ranges above 0-10 psi. Ni-Span C® has exceptional temperaturestability and eliminates the need foran expensive thermal compensator.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

724

12" Pressure GaugeRange Catalog Minor Inches Catalog MinorPressure PSI No. Graduations Price of Water No. Graduations Price0-15 PSI HS649201 .02 $1,990.00 0-500" HS649216 1 $2,135.000-30 PSI HS649202 .05 1,990.00 0-750" HS649217 1 2,135.000-50 PSI HS649203 .1 1,835.00 0-1000" HS649218 2 2,135.000-75 PSI HS649204 .1 1,835.00 Vacuum0-100 PSI HS649205 .2 1,835.00 0-30" Hg HS649219 .05 2,135.000-200 PSI HS649206 .5 1,835.00 Compound Ranges0-500 PSI HS649207 1 1,835.00 -30" Hg-15PSIg HS649220 .05-.02 2,135.000-1000 PSI HS649208 2 1,835.00 -30" Hg-60PSIg HS649221 .05-.1 2,135.000-1500 PSI HS649209 2 1,990.00 -30" Hg-150PSIg HS649222 .05-.2 2,135.000-2000 PSI HS649210 5 1,990.00 Catalog No. Description0-3000 PSI HS649211 5 1,990.00 HS649106 Bi-Metallic Temperature Compensation 180.000-5000 PSI HS649212 10 1,990.00 HS649103 Peak Load Indicator 245.000-7500 PSI HS649213 10 1,990.00 HS649102 Slotted Link for pressure relief protection 115.000-10,000 PSI HS649214 20 2,090.00 HS649104 Wall Mounting Bracket (installed) 90.000-20,000 PSI HS649215 20 2,510.00 HS649105 Metric Scales in mm of Hg, Bar, Kg/cm2, KPA and MPA Scales InquireNISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

Precision 12" Dial Pressure Gauge

SPECIFICATIONS Model A4AAccuracy Traceable to NIST ± 0.1% of Span

Mil-Std-45662A (Calibration Systems) Includes Calibration certificateANSI B40.1 (Recommended Practices), Grade 4A

Repeatability ± 0.02% of SpanHysteresis <0.1% of SpanSensitivity 0.01% of SpanPressure Ranges 0/15 PSI through 0/100,000 PSI“Unitized” Bourdon Tube Materials/ Standard OptionalPressure Ranges Beryllium Copper 0/15 PSI through 0/40 PSI 0/50 PSI through 0/10,000 PSI

403 Stainless Steel 0/50 PSI through 0/100,000 PSI 0/15 PSI through 0/40 PSIStandard Pressure Inlet Type And Location 1⁄4 NPT Male Bottom 0/15 PSI through 0/10,000 PSI

Autoclave F250-C (Aminco 45-11310)-Back Connect Over 10,000 through 100,000Optional Pressure Inlet Type And Location 1⁄8 NPT-Male or Female-Back or Bottom Specify Type and Location

1⁄4 NPT-Male or Female-Back or BottomAutoclave F250-C-Female Only-Back or Bottom

Double Scale (PSI In. Hg, etc.) OptionalOptional Pressures Types (Gauge Pressure-Standard) Absolute, Vacuum, CompoundBi-Metallic Temperature Compensator Eliminates temperature errors from -25°F to + 125°F Optional

• Unique unitized Bourdon tube design elimi-nates welded joints and crevices for positivecleaning. Bourdon tube materials of berylliumcopper and 403 stainless steel. Tip bleedBourdon tube facilitates cleaning or purgingoperations

• Accuracy of ± 0.1% of span, traceable to NIST.Meets MIL-Std-45662 and ANSI B40.1 Grade4A

• Pressure ranges available from VAC to 0-100,000 psi or in metric equivalents

• Solid front aluminum case with stainless steelpressure relief back for operator safety

• Dial sizes also available in 6", 81⁄2"(see page 592)

• Overload and underload stops protect move-ment from disengagement

• Ball bearing movement assembly assuressmooth and precise gauge operation

• White dial, knife-edge pointer with a mirror ring

NIST it ™

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

The Meri-Cal II is a microprocessor based pres-sure calibrator with 4 1⁄2 digit resolution and±0.25% of full scale accuracy. Multi-sensor capa-bility allows measurement of differential pres-sure, static pressure, electrical current and volt-age in one unit. Any two o these measurement canbe displayed on a 4 line by 20 character alpha-nu-meric display. The Meri-Cal II can measure anddisplay the pressure in any of eleven engineeringunits. A user units feature allows calculation anddisplay of custom pressure units. An adjustabledamping feature eliminates the effects of pulsat-ing pressures; a Min/Max function captures theextremes of varying pressure signals; and a Holdbutton can freeze the display at any point of inter-est. DN models offer a gas flow function to displayflow rate in user defined units. For transmitterand transducer calibrations, the electrical inputshave ranges of ±50 mA and ±50 VDC. Each Meri-Cal II is certified traceable to NIST.

Pressure Calibrator for Liquids and Gases

Catalog No. Model Description PriceMR3600 3600 Meri-Cal II (Must order one or two sensors $649.00

from the selection below. For two sensors, both must have the same accuracy)

Sensors

Catalog No. Accuracy Model Description PriceMR12136 .025% DN0200 0-200” H2O Differential 595.00MR12137 .025% DN2000 0-2000” H2O Differential 595.00MR12138 .025% GI0020 0-20 PSI Gauge 703.00MR12139 .025% GI0200 0-200 PSI Gauge 703.00MR12140 .025% GI2000 0-2000 PSI Gauge 703.00MR12141 .025% AI2000 0-2000mm Hg Absolute 703.00AccessoriesMRK Calibration Kit, includes: (3) Nylon tubing, 6 ft. 352.00

(3) Adapter, 1⁄8" O.D. tube to 1⁄8" MNPT (2) Tee,Brass 1⁄8" O.D. tubing, (1) Adapter, 3⁄16" hosebarb to 1⁄8" MNPT and carrying case

MR84066 Hand Pump (Pressure) 301.00MR84067 Vacuum Hand Pump 301.00MR84082 Test Leads 28.00MR84083 A34386 connector Kit 68.00MR84084 ABS Plastic Case 87.00MR84091 1' Hose High, Pressure Connectors 90.00MR84092 High Pressure to 1⁄8" female NPT adapters (5) 125.00NISTPR44 NIST Traceable Certificate 199.00NISTPR45 NIST Traceable Certificate with Data 250.00

• Accuracy of ± 0.025% of Full Scale• No Temperature Effect from 23° to 122°F• 4 1⁄2 Digit Resolution• Multiple Sensors for Measurement of

Differential Pressure, Static Pressure,Voltage and Current

SPECIFICATIONSAvailable Sensor Accuracies ± 0.025% FS (23 to 122°F)

± 0.05% FS (23 to 122°F)Electrical MeasurementsCurrent ± 50.000 mA ± 0.025% FSVoltage ± 50.000 VDC ± 0.025% FSTemperature:Storage -40°F to 140°F (-40°C to 60°C)Operating 23°F to 122°F (-5°C to 50°C)Pressure Limits Twice range on GI/AI units. Twice range on

DN units when pressurized on high side only.150 PSI static on DN units when applied atthe same time to both sides of the sensor

Display 4 Lines x 20 characters LCD withsimultaneous presentation of any twomeasurements

Power Two 9 volt, field replaceable batteriesMedia Compatibility Non-isolated DN sensors for clean, dry,

non-corrosive gases. Isolated GI/AI sensors for fluids compatible with 316ss

ConnectionsPressure 1⁄8" female NPT, 316ss.Electrical Shielded Banana JacksEnclosure (8.5" x 5.2" x 3.0") ABS plastic case.FeaturesSelection of engineering units - PSI, inches H2O, kg/cm2, Pascals, mBars, Bars,mm Hg, inches Hg, cm H2O, and user selectable scalingDamping (averaging) - selectable from 0.1 seconds to 25 secondsMin/Max capture - capture speed is equal to the selected damping rateHold functionAccessories Supplied: Soft carrying case

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

726

Cat. No Model Description PriceFL71830 718-30G Pressure Calibrator, includes protective $1,695.00

yellow holster, TL75 test leads,Test clips and User manual (Vac/30 PSIG)

FL718100 718-100G Pressure calibrator includes protective 1,695.00yellow holster, TL75 test leads, Test clips and User manual (Vac/100 PSIG)

NISTPR44 — NIST Traceable Certificate (for calibrators) 199.00NISTPR45 — NIST Traceable Certificate 250.00

with Data (for calibrators)Pressure ModulesFL700HTP 700HTP Hydraulic Test Pump (10,000 PSI) 849.00FL700PTP 700PTP Pneumatic Test Pump (360 PSI) 449.00FL700IV FL700-IV Current Shunt 209.00FL700PO1 700PO1 Pressure Module, 0-10 In, H20 Diff. 995.00FL700PO2 700PO2 Pressure Module, 0-1 PSID 895.00FL700PO3 700PO3 Pressure Module, 0-5 PSID 895.00FL700PO4 700PO4 Pressure Module, 0-15 PSID 995.00FL700PO5 700PO5 Pressure Module, 0-30 PSIG 995.00FL700PO6 700PO6 Pressure Module, 0-100 PSIG 995.00FL700PO7 700PO7 Pressure Module, 0-500 PSIG 995.00FL700PO8 700PO8 Pressure Module, 0-1,000 PSIG 995.00FL700PO9 700PO9 Pressure Module, 1,500 PSIG 995.00FL700P22 700P22 Pressure Module, 0-1 PSID, Wet 995.00FL700P23 700P23 Pressure Module, 0-5 PSID, Wet 995.00FL700P24 700P24 Pressure Module, 0-15 PSID, Wet 995.00FL700P27 700P27 Pressure Module, 0-30 PSIG, Wet 995.00FL700P29 700P29 Pressure Module, 3,000 PSIG, Wet 1,695.00FL700P30 700P30 Pressure Module, 5,000 PSIG, Wet 1,695.00FL700P31 700P31 Pressure Module, 10,000 PSIG, Wet 1,695.00FL700PA3 700PA3 Pressure Module, 0-5 PSIA 1,095.00FL700PA4 700PA4 Pressure Module, 0-15 PSIA 1,095.00FL700PA5 700PA5 Pressure Module, 0-30 PSIA 1,095.00FL700PA6 700PA6 Pressure Module, 0-100 PSIA 1,095.00FL700PCK 700PCK Pressure Module Calibration Kit 629.00FL700PD2 700PD2 Pressure Module ± 1 PSID 1,095.00FL700PD3 700PD3 Pressure Module ± 5 PSID 1,095.00FL700PD4 700PD4 Pressure Module ± 15 PSId 1,095.00FL700PD5 700PD5 Pressure Module -15 + 30 PSIG 1,095.00FL700PD6 700PD6 Pressure Module -15 + 100 PSIG 1,095.00FL700PD7 700PD7 Pressure Module -15 =200 PSIG 1,095.00MR84066 B34686 Pressure Pump 145 PSI Max 274.00FL700PV3 700PV3 Pressure Module -5 PSID 1,095.00FL700PV4 700PV4 Pressure Module -15 PSID 1,095.00NISTMD01 NIST Traceable Certificate (for modules) 125.00NISTMD02 NIST Traceable Certificate 159.00

with Data (for modules)

Features a Built-In Pressure/Vacuum Pump

718 Pressure Calibrator

• Built-in pressure/vacuum handpump, with vernier and bleed valve

• Pressure measurement to 0.05% offull span, using and internal pres-sure sensor

• Pressure measurement to 10,000psi/700 bar using any of the Fluke-700Pxx pressure Modules

• Wide range of selectable measure-ment units for pressure

• Current measurement with 0.025%accuracy and 0.001 mA resolution

• 24 volt loop power supply• Min-Max Hold functions• Simple, push-button user interface• Rugged — Ideal for field use

SPECIFICATIONSCompact and lightweight 210 mm L x 83 mm W x 62 mm D

(8.25 in. L x 3.27 in. W x 2.44 in. D)Operating Temperature -10°C to 55°CMaximum voltage 30 voltsNon-operating temperature -40°C to 60°COperating temperature -10°C to 55°CRelative humidity 95% (10°C to 30°C); 75% (30°C to 40°C);

45% (40°C to 50°C); 35% (50°C to 55°C)Operating altitude 3,000m maxShock 1 m drop testVibration Random, 2g, 5-500 HzSafety CSA C22.2 No. 1010.1:1992EMC EN50082-1:1992 and EN55022:1994; Class BSize/Weight 210 mm L x 83 mm W x 62 mm D

(8.25in. L x 3.27in. W x 2.44in. D); 737 g (26 oz)Power Two 9V ANSI/NEDA 1604A or IEC 6LR619V

alkaline batteriesBattery Life 4 to 20 hours, typical, depending on functions usedWarranty Three years (one year on pressure pump)

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

710 Series Pressure Calibrators NIST it

Cat. No Model Description Price Cat. No Model Description Price

FL7130G 717 30G Fluke 0-30 Psig Pressure Calibrator $995.00FL717100G 717 100G Fluke 0-100 Psig Pressure Calibrator 795.00NISTPR44 — NIST Traceable Certificate (for calibrators) 199.00NISTPR45 — NIST Traceable Certificate 250.00

with Data (for calibrators)Pressure ModulesFL700PO1 700PO1 Pressure Module, 0-10 In, H20 Diff. 995.00FL700PO2 700PO2 Pressure Module, 0-1 PSID 895.00FL700PO3 700PO3 Pressure Module, 0-5 PSID 895.00FL700PO4 700PO4 Pressure Module, 0-15 PSID 895.00FL700PO5 700PO5 Pressure Module, 0-30 PSIG 995.00FL700PO6 700PO6 Pressure Module, 0-100 PSIG 995.00FL700PO7 700PO7 Pressure Module, 0-500 PSIG 995.00FL700PO8 700PO8 Pressure Module, 0-1,000 PSIG 995.00FL700PO9 700PO9 Pressure Module, 1,500 PSIG 995.00FL700P22 700P22 Pressure Module, 0-1 PSID, Wet 995.00FL700P23 700P23 Pressure Module, 0-5 PSID, Wet 995.00FL700P24 700P24 Pressure Module, 0-15 PSID, Wet 995.00FL700P27 700P27 Pressure Module, 0-30 PSIG, Wet 995.00FL700P29 700P29 Pressure Module, 3,000 PSIG, Wet $1,695.00

FL700P30 700P30 Pressure Module, 5,000 PSIG, Wet 1,695.00FL700P31 700P31 Pressure Module, 10,000 PSIG, Wet 1,695.00FL700PA3 700PA3 Pressure Module, 0-5 PSIA 1,095.00FL700PA4 700PA4 Pressure Module, 0-15 PSIA 1,095.00FL700PA5 700PA5 Pressure Module, 0-30 PSIA 1,095.00FL700PA6 700PA6 Pressure Module, 0-100 PSIA 1,095.00FL700PCK 700PCK Pressure Module Calibration Kit 629.00FL700PD2 700PD2 Pressure Module ± 1 PSID 1,095.00FL700PD3 700PD3 Pressure Module ± 5 PSID 1,095.00FL700PD4 700PD4 Pressure Module ± 15 PSId 1,095.00FL700PD5 700PD5 Pressure Module -15 + 30 PSIG 1,095.00FL700PD6 700PD6 Pressure Module -15 + 100 PSIG 1,095.00FL700PD7 700PD7 Pressure Module -15 =200 PSIG 1,095.00MR84066 B34686 Pressure Pump 145 PSI Max 274.00FL700PV3 700PV3 Pressure Module -5 PSID 1,095.00FL700PV4 700PV4 Pressure Module -15 PSID 1,095.00NISTMD01 NIST Traceable Certificate 125.00

(for modules)NISTMD02 NIST Traceable Certificate 159.00

with Data (for modules)

For all models of the 710 Series• Simple controls• Clear, 5 digit, liquid crystal display• Operating temp. -10°C to 55°C• Safety: CSA C22.2 No. 1010.1:1992• 3 year warranty• Included:- Fluke 710 Series Process Calibrator- C81Y Protective Yellow Holster with

Flex-Stand™- Test leads and alligator clips - Single 9V alkaline battery- Instruction sheet (14 languages)- Statement of Calibration Practices

Pressure Calibrators• Measure pressure, 0.05% of full

scale• Measure mA, 0.025%• Calibrate I/P transmitter with

simultaneous pressure and current measurement

• Select eleven different engineeringunits

• Compatible with non-corrosivegases and liquids

• Zero, min, max, hold functions• 1⁄8" NPT female pressure fitting• Two shrouded banana jacks

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

728

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Documenting Pressure Calibrators NIST it

New Bright White Display

741B A Complete Documenting CalibratorThe 741B is the economical choice for plants that don’t use

PCs or that require traditional paper forms. It has storage capacity for a day’s calibration and measurement data. Whenyou’re back at the shop, recall the data on screen to fill out calibration forms.

743B More memory, Plus a PC Interface and DataLogging

The 743B has all the capabilities of the 741B plus a PC interface that lets you download procedures, lists, and instructions created with software - or upload data for print-ing, archiving, and analysis. With its expanded memory, the743B can hold a full week of calibrations and procedures.

744 Calibrates and Communicates with HARTInstruments

The new Fluke 744 is our most powerful DocumentingProcess Calibrator. It is enhanced with the ability to calibrateand communicate with Hart instruments. One rugged tool offers the most complete Hart implementation available within a field calibrator.

DPC/TRACK Software for InstrumentationManagement

Manage your instruments and your calibration data withthis easy-to-use instrumentation management database.Create calibration procedures, lists, and instructions on your PC and download them to the 743B or 744. Upload yourcalibration data back to your PC. Print reports or export datain standard ASCII format.

Pressure ModulesAn optional set of external pressure modules provides

pressure calibration and measurement capabilities. Twenty-seven modules are available, with basic accuracyspecs to 0.05%. Ranges start at 0-10”H2O (0-2.5 kPa) and go to 0-10,000 psi (0-70,000 kPa).

Standard EquipmentEvery fluke 741B, 743B and 744 comes with two sets of

TL24 industrial test leads, two sets of AC20 test clips, one setof TP20 test probes, a BP7217 battery pack, a BC7210 batterycharger, an instruction manual, and all units are shipped withNIST traceable certificates. Every 743B includes a serial portcable and a DPC/TRACK Sample, including complimentaryupload/export utility software. DPC/TRACK software includessoftware disks, an instruction manual, a serial port cable, anda DB9 to DB25 (9-pin to 25-pin) adapter.

xCat. No Model Description PriceFL741 741B Fluke Documenting Process Calibrator $2,995.00FL743 743B Fluke Documenting Process Calibrator 3,995.00FL744 744 Fluke Documenting Process Calibrator 4,750.00

with HART capabilitiesRENT743B — Weekly Rental — Fluke 743B 500.00NISTPC44 — NIST Traceable Certificate (for calibrators) 199.00NISTPC45 — NIST Traceable Certificate 250.00

with Data (for calibrators)Process Calibrator Modules and AccessoriesFL700HTP 700HTP Hydraulic Test Pump (10,000 PSI) 849.00FL700PTP 700PTP Pneumatic Test Pump (360 PSI) 449.00FL700IV 700IV Current Shunt 209.00FL700P01 700P01 Pressure Module, 0-10 In, H20 Diff. 995.00FL700P02 700P02 Pressure Module, 0-1 PSID 895.00FL700P03 700P03 Pressure Module, 0-5 PSID 895.00FL700P04 700P04 Pressure Module, 0-15 PSID 895.00FL700P05 700P05 Pressure Module, 0-30 PSIG 995.00FL700P06 700P06 Pressure Module, 0-100 PSIG 995.00FL700P07 700P07 Pressure Module, 0-500 PSIG 995.00FL700P08 700P08 Pressure Module, 0-1,000 PSIG 995.00FL700P09 700P09 Pressure Module, 1,500 PSIG 995.00FL700P22 700P22 Pressure Module, 0-1 PSID, Wet 995.00FL700P23 700P23 Pressure Module, 0-5 PSID, Wet 995.00FL700P24 700P24 Pressure Module, 0-15 PSID, Wet 995.00FL700P27 700P27 Pressure Module, 0-30 PSIG, Wet 995.00FL700P29 700P29 Pressure Module, 3,000 PSIG, Wet 1,695.00FL700P30 700P30 Pressure Module, 5,000 PSIG, Wet 1,695.00FL700P31 700P31 Pressure Module, 10,000 PSIG, Wet 1,695.00FL700PA3 700PA3 Pressure Module, 0-5 PSIA 1,095.00FL700PA4 700PA4 Pressure Module, 0-15 PSIA 1,095.00FL700PA5 700PA5 Pressure Module, 0-30 PSIA 1,095.00FL700PA6 700PA6 Pressure Module, 0-100 PSIA 1,095.00FL700PCK 700PCK Pressure Module Calibration Kit 629.00FL700PD2 700PD2 Pressure Module ± 1 PSID 1,095.00FL700PD3 700PD3 Pressure Module ± 5 PSID 1,095.00FL700PD4 700PD4 Pressure Module ± 15 PSId 1,095.00FL700PD5 700PD5 Pressure Module -15 + 30 PSIG 1,095.00FL700PD6 700PD6 Pressure Module -15 + 100 PSIG 1,095.00FL700PD7 700PD7 Pressure Module -15 =200 PSIG 1,095.00MR84066 B34686 Pressure Pump 145 PSI Max 274.00FL700PV3 700PV3 Pressure Module -5 PSID 1,095.00FL700PV4 700PV4 Pressure Module -15 PSID 1,095.00FL700SW 700SW DPC/Track Instrumentation Management 1,795.00

Software for Models 702, 743 and 744FL700TC1 700TC1 T/C Mini-Plug kit 10 common types 65.00FL700TC2 700TC2 T/C Mini-Plug kit 5 common types 55.00NISTMD01 NIST Traceable Certificate (for modules) 125.00NISTMD02 NIST Traceable Certificate 159.00

with Data (for modules)AccessoriesBC7210 BC7210 Battery Charger 119.00BE9005 BE9005 Battery Eliminator 63.00BP7217 BP7217 Nicad Battery Pack 129.00C700 C700 Hard Carrying Case (700 Series) 159.00C781 C781 Soft Carrying Case 39.00C789 C789 Soft Carrying Case 80.00



H

Dual Range Pressure Calibrator

Catalog No. Model Description PriceML200101 PPC-3300 Dual range pressure calibrator with .05% of reading accuracy $1,995.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

NIST it

.05% of Reading Accuracy• Dual isolated 316SS pressure sensors with

a rugged nickel plated manifold designed forharsh environments

• Robust design - A NEMA 4X water resistantsealed case and a sealed membrane keypad suited for the most rigorous applications

• Versatile broad pressure ranges individuallytemperature compensated for high accuracyover a broad operating range of 0-50°C

• Engineering units: PSI, in H2O (4°C), in H2O(20°C), in H2O (60°C), ft H2O (4°C), ft H2O(20°C), cm H2O (4°C), cm H2O (20°C), m H2O (4°C), m H2O (20°C), BAR, Kg/cm2,kPa, mPa, mm Hg, m Hg

• Communications through an RS232 port forreal time data transfer to a PC or printer

• Dual Range — ideal for custody transfer andmass flow applications

• % Error function automatically calculatestransmitter error during calibration

• Integral 24 VDC power supply to power various devices under test

• MIN/MAX storage and retrieval• Class I Division I Group C & D Certification

pending• Pressure switch test feature

SPECIFICATIONSPressureRanges 1 PSI to 5.000 PSI (0 to 135" H2O) non-corrosive

gases and liquids-5 PSI to 30.000 PSI-5 PSI to 100.00 PSI-12 PSI to 300.00 PSI-12 PSI to 3000.0 PSI

Accuracy 5 PSI: ± 0.5% of reading ± 0.001 PSI30 PSI: ± 0.5% of reading ± 0.002 PSI100 PSI: ± 0.5% of reading ± 0.02 PSI300 PSI: ± 0.5% of reading ± 0.02 PSI3000 PSI: ± 0.5% of reading ± 0.2 PSIVacuum: 0.5PSI, all ranges

ElectricalRanges 0 to 24.000 mA

0 to 10.000 VAccuracy ± 0.025% of reading ± 2 LSD18°C to 28°CInput Protection 1/8 A FuseEnvironmentalOperating Temp 0°C to 50°CStorage Temp 20°C to 60°CStability ± .005% F.S./°C for both pressure and electrical

for temperatures outside of 23°C ± 5°CMediaAny gases/liquids compatible with 316SS and nickel plated brassPower: 4 AA Alkaline Cells or 4 AA Ni-Cd Cells, Optional ACAdaptor, Ni-Cd Charger AvailableSize 7 1/2" x 4" x 1 1/2"

Pressure Calibrator Manometer NIST it

Rugged, Dust Tight, Water Resistant Housing• High accuracy gauge or

differential capability• Rugged, dust tight,

water resistant case• Isolated SS sensors on

300 PSI and 3000 PSIunits

• Easy to read Super-TwistLCD

• Intuitive controls makeoperation easy even forinfrequent users

• Powered by a common 9volt battery

SPECIFICATIONSRanges -14.00 to 30.00 PSIG/PSID

-14.0 to 100.0 PSIG/PSID-14.0 to 300.0 PSIG-14.0 to 3000 PSIG± 200" H2O

Resolution 30 PSI - .001 PSI100 PSI - .01 PSI300 PSI - .01 PSI3000 PSI - 0.1 PSI200" - 0.01 in H2O

Accuracy1 ± 0.05% F.S. ± 1 LSD30/100 PSI -5 PSI to Full Scale300/3000 PSI ± .05% of Reading ± 2 LSDNote: for vacuum accuracy is 0.1% of F.S. ± 1 LSD200" ± 0.1% F.S. ± 1 LSD

Operating Temp 0 to 50°CStorage Temp -20 to 60°CTemp Stability2 0.01% F.S./°CMAX Overpressure 2xPorts Two 1/8" FNPTMedia 30 PSI Non-Corrosive Gas or Liquids

100 PSI Non-Corrosive Gas or Liquids200" Non-Corrosive Gas or Liquids

300 PSI All Media3000 PSI All Media

Engineering Units PSI, in H2O, ft H2O, cm H2O, m H2O, in Hg, mm Hg, cm Hg, mBAR, BAR, kPa, Kg/cm2, TORR, ATM

Key Features Zero, Min/Max, Clear, Damp & HoldWeight 14 oz.NOTE 1 18°C to 28°CNOTE 2 0 to 18°C and 28°C to 50°C

Catalog No. Model Description PriceT14030 T140-30 Pressure Calibrator Manometer, 30 PSI Range $595.00T140100 T140-100 Pressure Calibrator Manometer, 100 PSI Range 595.00T140200 T140-200 Pressure Calibrator Manometer, 200" H2O Range 595.00T140300 T140-300 Pressure Calibrator Manometer, 300 PSI Range 795.00T1403000 T140-3000 Pressure Calibrator Manometer, 3000 PSI Range 795.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

All gases and liquidscompatible with 316SS and nickel platedbrass


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

730

Microprocessor Based Pressure Calibrator

Catalog No. Model Description PriceML900150 PPC-9001-5 Microprocessor based pressure calibrator, 5psi with case, batteries, test leads & manual $1,099.00ML900130 PPC-9001-30 MIcroprocessor based pressure calibrator, 30psi with case, batteries, test leads & manual 1,099.00ML900110 PPC-9001-100 Microprocessor based pressure calibrator, 100psi with case, batteries, test leads & manual 1,099.00ML900111 PPC-9001 Kit Pressure calibrator with hand pump, carrying case, AC adapter, fittings, tools & manual 1,399.00

AccessoriesML342104 MECP-100 Pressure Calibrator Pump 295.00ML342103 1001-9V 9 volt adapter/charger 22.00ML02 10077 Ni-Cd Battery (each) — Requires 4 8.50NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

Microprocessor Based Pressure Calibrator

The PPC-9001 Precision Pressure Calibrator is de-signed to meet the needs of the most demanding fieldcalibration applications. Its microprocessor designyields many useful features including a built-in RS-232port for data transfer to a PC. The PPC-9001 offers awide range of pressure media compatibility and a pres-sure connection manifold which allow secure mountingof the optional hand pump. The built-in loop power sup-ply along with milliamp or voltage read capability makethe PPC-9001 ideal for calibrating pressure and flowtransmitters.

SPECIFICATIONSOperating Range

Model Model ModelRanges PPC-9001-5 PPC-9001-30 PPC-9001-100PSI 0-5.000 0-30.000 0-100.00In H2O 0-138.40 0-830.4 0-2768.0cm H2O 0-351.5 0-2109.0 0-7030mm H2O 0-3515 0-21090 0-70310BAR 0-0.3447 0-2.0680 0-6.895Kg/cm2 0-0.3515 0-2.1090 0-7.030mm Hg 0-258.60 0-1551.0 0-5171Kpa 0-34.47 0-206.90 0-689.5Range, Electrical mA 0 to 24.000

Volts 0 to 20.000Accuracy 0.05% ± 1LSD for both pressure and mA/VLoop Power 24Vdc ± 10% Built-inStability 0.01%/°COperating Temperature 0 to 50°CStorage Temperature -20 to 60°CMedia Compatibility Non-Corrosive Gasses or Liquid

For Corrosive Media Contact the FactoryConnections Pressure- 1⁄8"FNPT inlet with two, 1⁄8"FNPT fittings

available for optional hand pump or pressure gaugeCurrent Overload 1⁄8 A FuseProtectionPower 4AA Alkaline Cells or 4AA Ni-Cd Cells

Optional AC adapter, Ni-Cd Charger AvailableSize 7" x 3.8" x 1.6"

• 0.05% Full Scale Accuracy • Microprocessor Based Design• Compatible with Wide Range of

Pressure Media• Simultaneous Display of

Pressure vs Milliamps or VoltageSignals

• Built-in 24 Volt Loop PowerSupply

• Built-in RS-232 Interface• Optional Hand Pump Attaches as

Pressure Source• Rugged manifold with three con-

nection ports• Easy user access to cal. pot.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Pressure CalibratorKit



H

Handheld Pressure Calibrator

The ATE-100 Handheld PressureCalibrator measures pressure, flow, vacuum,leak, current, voltage and change-of-statefor switch testing.

Each system consists of a base unit and one ortwo Quick-Select™ pressure modules with pres-sure ranges from 0.25 inches H2O to 10,000 psi.Modules can be interchanged quickly and easilywithout the use of tools. A standard RS-232 portallows for computer interfacing.

Catalog No. Model Description PriceAS10010 ATE-1 ATE-100 Handheld Pressure Calibrator $1,230.00

with datalogging, Hi/Lo alarm relays, batteries and test leads

AS10011 ATE Kit 1A Soft carrying case and AC adapter 125.00

AS10012 ATE Kit 1B Hard carrying/transport case and AC adapter 150.00

AS10013 — Extended temperature Operation 110.00-4°F to 120°F (32°F to 120°F standard)

AQS-1 Low Pressure Quick Select Pressure Modules, Dual Port Gauge

Differential Ranges: 0.25, 0.5 or 1.0 inches H2O Please specifyAS10021 ± 0.07% accuracy Pressure Module 1,000.00

AS10022 ± 0.10% accuracy Pressure Module 840.00

Differential Ranges: 2.0, 3.0, 5.0, 10.0, 15.0, 25.0, 50.0, 100, 150 or 200inches H2O Please specifyAS10024 ± 0.06% accuracy Pressure Module 795.00


Compound Ranges: ± 0.125, ± 0.25 or ± 0.5 H2O Please specifyAS10027 ± 0.07% accuracy Pressure Module 1,010.00


Compound Ranges: ± 1.0, ± 1.5, ± 2.5, ± 5.0, ± 7.5, ± 12.5, ± 25.0, ± 50.0or ± 100 H2O Please specifyAS10030 ± 0.06% accuracy Pressure Module 840.00


AQS-2 Quick Select Pressure ModulesPressure Ranges: 5,10,15,30,50,60,100, 150, 200, 250 or 300 psiPlease specifyAS10033 ± 0.05% accuracy Pressure Module 745.00


AS10035 ± .025% accuracy Pressure Module 805.00

Pressure Ranges: 500, 600, 1000, 1500, 2000, 2500, 3000, 5000, 6000 or7500 psi Please specifyAS10036 ± 0.05% accuracy Pressure Module 865.00



Vacuum Ranges: 5, 10 or 15 psi Please specifyAS10040 ± 0.05% accuracy Pressure Module 835.00



Compound Ranges: -5/+5, -10/+10, -15/+15, -15/+30 or -15/+60 psiPlease specifyAS10043 ± 0.05% accuracy Pressure Module 835.00



RTDAS310 RTD Interface Module 415.00

AS315 4 wire Pt100 RTD, Probe class A, 12" x 1/4" and 275.00male mating connector for bare RTD wire

Accessories

Catalog No. DescriptionAS321 Optional Enhanced Accuracy — No additional error due to 120.00

temperature over the compensated range

NISTPR44 NIST Traceable Certificate 199.00NISTPR45 NIST Traceable Certificate with Data 250.00

• Interchangeable pressure and temperature modules• Pressure measurement accuracies of ± .025, .05, .10% of span• Supports most standard RTD probes• Supports thermocouple measurements• FM Approval or CE Mark• Optional enhanced accuracy• Data-logging and cert generation available• Includes two 9V batteries, test leads, AC adapter and soft carrying case

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

732

Designed for use in remote locations where AC power is not available, the DPI 603 enables pres-sure instrumentation to be serviced and calibrated.

The instrument features the capability to generate pneumatic test pressures with an integralhand-pump up to 300 psi. A volume adjuster provides fine control of the desired test value and aventing valve enables pressure release without disconnection of the device under test.

An optional pressure/vacuum switching facility can also be provided, which enables thehand-pump to source vacuum down to -22" Hg or pressure up to 300 psi g.

To facilitate pressure transmitter testing and calibration a 24 VDC power supply is pro-vided and the ability to monitor the current loop from 0 to ±55 mA DC.

For loop verification, the DPI 603 can also output a single 12mA test value, or providea passive sink if required.

The clear LCD allows readout of pressure, voltage and current parameters with theability to show current or voltage simultaneously with pressure.

Portable Pressure Calibrator

Catalog No. Model Description PriceDR7750011 DPI 603 Portable Pressure Calibrator includes hand pump, volume adjuster, vent value, carrying case, batteries, manual, $1,250.00

electrical test leads and NIST Traceable CertificateDR7750012 DPI 603A Portable Pressure Calibrator with pressure vacuum capability (includes the same accessories as basic unit above) 1,460.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

SPECIFICATIONSPressure Measurement SpecificationOperating Pressure Standard full scale ranges can be specified of Ranges -14.7 psig to + 15 psi, + 30 psi, 100 psi or 300psigOverpressure The rated pressure can be exceeded by 2 x

causing negligible calibration change, subjectto a maximum safe working pressure of 350 psi

Pressure Media Fluids compatible with 316 Stainless Steel,Hastelloy C276, Nylon, Viton and brass

Accuracy Combined non-linearity, hysteresis an repeatability± 0.075% F.S. for positive or negative pressures± 1 digit

Temperature Effects Over 32° to 105°, the averaged Span temperaturecoefficient will not exceed 0.007% of reading/°F.

Digital Indicator Readout & Display± 99999 capability, 0.54" LCD digits with additional16 text characters

Pressure Scale Units 24 scale units are providedpsi, lb/ft2, inHg, inH2O, ft of H2O, (40° and 68°F) torr, atm, Pa, kPa, MPa, kPa, mbar, bar, kg/cm2,kg/m2, mmHg, cmHg, mHg, mmH2O, cmH2O,mH2O, Special 2 units are presented on the display

Display Overload Instruments are capable of nominal 120% F.S.Above this, an overrange error code is displayed.

Resolution ± 0.005% F.S. maximumResponse Nominal rate of three readings per second on the

digital displayZero Control Offset correction for pressure and electrical scales

by key-press, protected against accidental use

Calibration Control Front panel key-pad calibration controls forpressure and electrical ranges

Position Effect NegligibleElectrical SpecificationElectrical InputsVoltage MeasurementRange ± 50VAccuracy ± 0.15% of reading ± 0.02% F.S.Temperature Coefficient ± 0.006% reading/°FCurrent MeasurementRange ± 55mAAccuracy ± 0.075% of reading ± 0.005% F.S.Temperature Coefficient ± 0.006% reading/°FElectrical OutputsVoltage output 24V nominal, floating, 25mA maximumCurrent output Loop check fixed 12mA nominal, source or sinkPower SupplyBattery powered 4 x 1.5V zinc carbon “D” cells, 50 hours nominal continuous operationwith no load on output terminals. Battery low condition indicated by display symbolSafetyIEC 1010EMC immunity to IEC 801-804Certification CE markedPhysical SpecificationWeight 9 lbsDimensions 12.6" x 7.7" x 5.0" nominalPressure Connection 1/8" NPT femaleCarrying Case Supplied standard and with a complete set of accessories

NIST it

Dirt Moisture TrapThe IDT600-2 has no diaphragm or other internal components

which could create a pressure drop and does not affect calibration ac-curacy. The unit is simple to dismantle and easy to clean. It shouldbe periodically cleaned to prevent excessive contaminate build-upwhich may overflow into the calibrator. The top and bottom sectionsare simply unscrewed, releasing the transparent chamber which isthen wiped clean.

The IDT600-2 is an effective barrier against the transfer of mois-ture and dirt from an instrument under test to any portable pressurecalibrator. Installed directly on the calibrator pressure port, regularuse of the IDT600-2 will prevent contamination of the calibrator'spneumatic system, improve long term reliability and reduce mainte-nance costs. In addition, it prevents dirt or moisture from one deviceunder test being transferred to another via the calibrator.

• Accuracy ± 0.075% F.S.• Integral pressure generation• Standard ranges up to 300 psig• 5 digit LCD, multiple engineering units

• Dual pressure & electrical readout• Transmitter supply & measurement• Current loop verification test• Vacuum generation available

Catalog No. Model Description PriceDR6002 IDT-600-2 Dirt moisture trap $190.00

• Can be used with any pressure calibrator

• Easy to install• Low maintenance• For pneumatic calibrators• Prevents cross-contamination



H

Precision Portable Pressure Calibrator

The DPI 605 precision pressure calibratorcombines micromachined silicon piezoresistiveand resonating element sensors with the latestmicroprocessor technology, features 0.05% ofreading accuracy. It is a totally self contained,battery powered pressure test and calibrationsystem. Standard features include electricalmeasurement and supply capability, pressureand vacuum generation, simultaneous displaysof pressure/vacuum and electrical parameters,extensive data processing and storage capabilityand RS 232 interface.

The DPI 605 features an impact resistant,splash and dust proof NEMA 4X enclosure. All ofthe main controls are via a membrane keypad.Data Log

This enables the DPI 605 to act as data loggerand store up to 10,000 readings. Record andReplay facilities are included.

SPECIFICATIONSPressure Measurement SpecificationsOperating Pressure Range -14.7 to + 300 psi

Option available for absolute pressures viaBarometric Reference sensor. See Option A

Pressure Scale Units PSI, ft. H2O, in Hg, kPa standard - 23 different scalesunder SET-UP, user selectable

Overpressure To 1.5x causing negligible calibration changePressure Media Compatible with most common non-corrosive gassesTransduction Principle Dual, integrated silicon strain gauge sensors. Optional

Barometric Reference utilizes vibrating silicon element.Readout ± 999999 capability on both pressure and electrical

parameters. ± 9999 for ranges below 1.5 psi (FS)Display 1.5" x 5.2" L.C.D. graphics panel. 240 x 64 pixels. Backlit.Display Overload 110% F.S. Pressure overrange nominal. Above this the

display flashes.Resolution 17 bits (0.00075% F.S.)Response 2 readings per second nominalZero Control Pressure offset correction by key press Ability under

process key to permit TARE of pressure, voltage andcurrent, either manual or displayed value.

Accuracy 0.05%, of reading between 1% and 100% F.S. 0.002 psibelow 1% F.S. Figure includes 90 day stability. Combinednon linearity, hysteresis and repeatability (included withinthe above accuracy figure).

Positive Pressures ± 0.025% of reading between 1% and 100% F.S. ± 0.001psi below 1% F.S.

Negative Pressures ± 0.025% of reading between -14.7 psi to -3 psi ± 0.001psi between 0 and -3 psi

Temperature Effects -14.7 to 300 psi gauge calibrator over 15° to 100°F theaveraged temperature coefficient ± 0.0012% of reading/°F

Position Effect NegligibleElectrical SpecificationsElectrical Inputs

Voltage Measurement 0 to ± 50 V DC auto ranging, resolution 10µV. Inputimpedance 10mΩ. Accuracy ± 0.04% of reading ± 1 digitincluding 90 day stability. ± 0.004% of reading/°F

Power Supply Supplied fitted with Ni-Cad rechargeable pack. Can alsobe powered by 6 x D cells, alkaline recommended. Battery Life: 25 hours nominal for Ni-Cad. 75 hoursnominal for alkaline. External PSU/charger unit suppliedas standard.

Current Measurement 0 to ± 55 mA d.c. resolution 0.001mA Internal resistancenominally 10Ω/ Accuracy 0.03% of reading ± 1 digitincluding 90 day stability. ± 0.004% of reading/°F

Electrical OutputsVoltage Output Programmable floating output in the range 0 to 24 V DC

max 50 mA. Suitable also for current loop energizing andswitch testing.

Current Output Programmable output in the range 0 to 55 mA DC forcurrent display calibrations. Configured as source,voltage limit 19 V. Configured as sink, voltage limitmaximum 30 V, voltage limit minimum 5V.

Analog Output Signal Proportional to displayed pressure. Accuracy s display. 0to 24 V DC with 16 bit (0.001% F.S.) resolution. Userprogrammable zero and full scale settings. Bandwidth 1to 2 Hz - updated each new reading. Current output canalso be provided either 0 to 50mA or 4 to 20mA for 0 toF.S. pressure

Environmental SpecificationsTemperature Operating 15° to 100°F Storage 0° to 140°FSealing Instrument NEMA 4X Battery charger to laboratory

standard.Electro Magnetic Compatibility Designed to meet BS6667/HD481 and BS6527 / EN55022.Physical SpecificationsDimensions/Weight 5.5 inches z 11 inches x 14.5 inches / 9 lbs. nominalPressure Connections 1⁄8 NPT femaleIncluded Carrying case and a complete set of test leads are included.

Improved Accuracy to ±.025% of reading

• Integral pressure/vacuumgeneration

• Barometric accuracy: ± 0.015%

• Voltage/current powersource

• Accuracy: ± 0.05% ofreading

• NEMA 4X sealed case • Data transfer via RS-232• Range: -14.7 to 300 psi• Functions include; peak

readings,switch testing,data logging, leak testing,limit setting, data analysis

NIST it

Catalog No. Model Description PriceDR639301 DPI605 Precision Portable Calibrator Standard instrument includes hand pump, volume adjuster, vent valve, $6,900.00

carrying case, test leads, rechargeable batteries, and charger. Range -14.7 psi to 300 psi gaugeDR639303 DPI605-E Portable printer for DPI605 1,600.00DR639304 DPI605-G Linkpak w/ 4.0-LPDPI 695.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

734

Portable Pressure CalibratorsPneumatic, Hydraulic and Low Pressure Differential

• Ranges vac to 10,000 psi, multi-rangeable

• Accuracy from ± 0.025% Full Scale• Fully documenting with RS 232• Generates Pressure and Vacuum• Dual Readout: Input and output

Pneumatic Calibrator DPI 610/615PC

• Pressure/vacuum pump -22 inHgto 300 psi capability

• Volume adjuster Fine pressureadjustment

• Release valve Vent and controlledrelease

• Pressure port - 1/8 NPT (female)• Media - Dry, non-corrosive, non-

conductive gasses compatible with316 stainless steel, HastelloyC276, BUNA-N and nylon

Hydraulic Calibrator DPI 610/615HC

• Priming pump - Feeds fromexternal source

• Shut-off valve - Open for systempriming

• Screw press - 0 to 6000 psicapability

• Pressure port - 1/8 NPT (female)• Media - Demineralized water

and most hydraulic oils

DPI 610/615 LP Series• Release valve - Vent and

controlled release• Pressure port - 1/8 NPT

(female)• Media - Dry, non-corrosive, non-

conductive gasses compatiblewith 316 stainless steel,Hastelloy C276, BUNA-N andnylon

Pneumatic Calibrator DPI 610/615PC Hydraulic Calibrator DPI 610/615HC DPI 610/615 LP Series

Electrical InputsInput Range Accuracy Resolution RemarksVoltage* ± 50Vd.c. ± 0.05%Rdg. ± 0.004%FS 100µV max Autoranging, >10MW

(± 30Vdc IS version)Current* ± 55mA ± 0.05%Rdg. ± 0.004%FS 0.001mA 10ohm, 50V max.Temperature 15° to 105°F ± 2°F 0.2°F Local ambientSwitch Open/Closed — — 5mA whettingElectrical OutputsOutput Range Accuracy Resolution RemarksVoltage 10Vd.c. ± 0.1% — Max. load 10mA

24Vd.c. ± 5% Max. load 26mACurrent* 0 to 24mA ± 0.05%Rdg. ± 0.1%F.S. 0.001mA —*Temperature coefficient ± 0.004% reading/°F w.r.t. 68°F.Special FeaturesPressure units 25 scale units plus one user defined.mA step Continuous cycle at 10 sec intervals.Function mA Output4 to 20mA linear 4 8 12 16 20 — —0 to 20mA linear 0 5 10 15 20 — —4 to 20mA flow 4 5 8 13 20 — —0 to 20mA flow 0 1.25 5 11.25 204 to 20mA valve 3.8 4 4.2 12 19 20 21mA ramp Continuous cycle with configurable end values and 60 sec travel time.Data log Multi-parameter with internal memory for 10,000 values. Variable sample period or log on key press. (615: log on key press for calibration results)Snapshot Paperless notepad. Stores up to 20 complete displays.Computer interface DPI 615 Bidirectional for downloading procedures and uploading results.Process functions Tare, max/min, filter, flow, % span.Language English, French, German, Italian, Portuguese and Spanish.Power management Auto power OFF, auto backlight OFF, battery low indicator and status on key press.DisplayPanel 2.36 x 2.36 inch graphic LCD with backlight.Readout ± 99999 capability, 2 readings per second.EnvironmentalOperating Temperature 15° to 120°FCalibrated Temperature 15° to 105°FHumidity 0 to 90%, non-condensing.Sealing Generally to NEMA 12 (IP54)Conformity EN61010, EN50081-1, EN50082-1, CE marked.Physical 7.7 lb, 11.8 x 6.7 x 5.5 inchesPower supply 6 x 1.5 V 'C' cells, alkaline (up to 65 hours nominal use at 68°F rechargeable battery pack and charger

are supplied as standard (20 hours nominal use).



H

Portable Pressure Calibrator DPI 610This self-contained, battery powered package contains a pressure generator, fine pressure control, de-

vice energizing and output measurement capabilities, as well as facilities for 4-20 mA loop testing anddata storage. The rugged design sealed generally to NEMA 12 (IP54) is ergonomically designed such thatthe pressure pump can be operated and test leads connected without compromising the visibility of thelarge dual parameter display. The mA step and ramp outputs and built-in continuity tester extend thecapabilities to include the commissioning and maintenance of control loops.Fully documenting version DPI 615

The DPI 615 provides error analysis for field reporting of calibration errors and pass/fail status. In ad-dition, procedures downloaded from a PC automatically configure the PDI 615 to pre-defined calibrationand test routines.DPI 610/615 LP Portable Low Pressure Calibrator

Incorporates a precision low-pressure sensor and pneumatic generation to provide a fully self-con-tained portable low-pressure calibrator.

The DPI 610/615 can be easily configured for dedicated tasks. For example: P-I task sets the calibratorto source pressure and measure mA, P-Display talk allows indicator readings to be manually entered andrecorded, for example when checking devices such as Magnehelic gauges.

Catalog No. Model Description PriceDR639108 DPI 610PC Portable Digital Calibrator, 5 psi $ 2,595.00DR639109 DPI 610PC Portable Digital Calibrator, 30 psi 2,595.00DR639110 DPI 610PC Portable Digital Calibrator, 100 psi 2,595.00DR639111 DPI 610PC Portable Digital Calibrator, 300 psi 2,595.00DPI 610 PC models includes pressure/vacuum pump, volume adjuster, vent valve, carrying case, rechargeable battery pack and charger, 25 user selectable scales as standard,calibration certificate,manual and electrical leads. DR639113 DPI 610HC High Pressure 3,650.00

DPI610HC standard instrument fitted with hydraulic pump, reservoir and screwpress and supplied with carrying case, rechargeable battery pack and charger, calibration certificate, manual and electrical leads. 25 selectable scales as standard. Specify Range: 1000 psi or 6000 psiDR639114 DPI 610LP Low Pressure 3,695.00DPI 610LP includes coarse and fine volume adjuster, vent valve, auto zero equalization,carrying case, test leads, 1/8” ID hose, a manual pressure/vacuum squeeze pump and 1/8” ID hose ”T” connec-tor, calibration certificate, user guide, rechargeable batteries and charger. 25 selectable scales as standard.Specify Range ±1, ±5, ±10, ±20, ±30 and ±60 in H20DR639123 DPI 615PC Portable Digital Calibrator 3,200.00DPI 615PC includes pressure/vacuum pump, volume adjuster, vent valve, carrying case, rechargeable battery pack and charger, calibration certificate, manual, electrical leads and 25 user selectablescales as standard.Specify Range: 5, 30, 100, and 300 psi gaugeDR639124 DPI 615HC High Pressure Calibrator 4,500.00DPI 615HC fitted with hydraulic pump, reservoir and screwpress and supplied with carrying case, rechargeable battery pack and charger, calibration certificate, manual, electrical leads and 25 userselectable scales as standard.Specify Range: 3000 psi or 6000 psiDPI 610PC, HC, LP Standard Options

DR191022 A022 Rechargeable battery pack (110Vac) & charger (P/N 191-A023) 110.00DR639112 191-129 Universal charger 75.00

Remote pressure sensors

DR639115 DA200-A145 1 and 2.5 psi gauge 995.00DR639116 — 5 to 500 psi gauge or absolute 795.00DR639117 — 1000 to 10,000 psi sg or abs 995.00DR639118 DA2200-A148 1 and 2.5 psi differential 1195.00DR639119 — 5 to 500 psi differential 995.00(Minimum of one Option B2 required per DPI 610 when ordering remote sensors)DR639120 LPE 9400 Low pressure remote sensor with low pressure hand pump, adapters, hose and 1195.00

carrying case. (Minimum of one option B2 required per DPI 610/615 when orderingremote sensors)

Specify Range: ±1, ±5, ±10, ±20, ±30 and ±60 in H20DR639121 (B2) Mating cable for remote sensors (P/N IA2405-06-I-VO) 85.00DR639122 (B3) Remote pressure sensor (150mV max.) Add 140.00DR639304 LPDPI Linkpak-W software 695.00DR639211 860-116 Spare carrying case 860-116 50.00

IDT 600-2 Dirt Moisture Trap 190.00Accessories

NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00NISTPRQ44 — 2 Year NIST Traceable Certificate 298.00NISTPRQ45 — 2 Year NIST Traceable Certificate with Data 375.00

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

736

SPECIFICATIONSAccuracy 0.025% FSOperating Temperature 32 to 104°F (0 to 40°C)Units PSI, bar, “H20, “Hg, mmHg (other units available)Display Backlit LCD, 16 character, 2 lineResolution 0.01% FSPower Supply 6V NiCad rechargeable with 110VAC charger

suppliedBattery Life 10 hours (fully charged)Calibration Medium Air, oil, waterConnections 7 pc. NPT adapter fitting provided with kits Weight 3.5 lbs (head only)Certification NIST Calibration Certificate

Pressure/Vacuum CalibratorsPressure Calibrator Vacuum to 15,000 psi with 0.025% accuracy

Catalog No. Description Stocked Ranges (any custom range is possible) PricePC6-PRO-2-I-3-P Complete kit / indicator head -30”Hg to 30 psi $2,305.00PC6-PRO-10-I-3-P Complete kit / indicator head -30”Hg to 150 psi 2,305.00PC6-PRO-20-I-3-P Complete kit / indicator head -30”Hg to 300 psi 2,305.00PC6-PRO-350-I-3-H Complete kit / indicator head 0 to 5,000 psi 3,000.00PC6-PRO-700-I-3-H Complete kit / indicator head 0 to 10,000 psi 3,000.00PC6-PRO-1000-I-3-H Complete kit / indicator head 0 to 15,000 psi 3,400.00PC6-PRO-2-C-3-P Complete kit / calibrator head -30”Hg to 30 psi 2,895.00PC6-PRO-10-C-3-P Complete kit / calibrator head -30”Hg to 150 psi 2,895.00PC6-PRO-20-C-3-P Complete kit / calibrator head -30”Hg to 300 psi 2,895.00PC6-PRO-350-C-3-H Complete kit / calibrator head 0 to 5000 psi 3,590.00PC6-PRO-700-C-3-H Complete kit / calibrator head 0 to 10,000 psi 3,590.00PC6-PRO-1000-C-3-H Complete kit / calibrator head 0 to 15,000 psi 3,990.00PC6-IS-2-C-3-P Complete kit / intrinsically safe head -30”Hg to 30 psi 3,375.00PC6-IS-10-C-3-P Complete kit / intrinsically safe head -30”Hg to 150 psi 3,375.00PC6-IS-20-C-3-P Complete kit / intrinsically safe head -30”Hg to 300 psi 3,375.00PC6-IS-350-C-3-H Complete kit / intrinsically safe head 0 to 5,000 psi 4,070.00PC6-IS-700-C-3-H Complete kit / intrinsically safe head 0 to 10,000 psi 4,070.00PC6-IS-1000-C-3-H Complete kit / intrinsically safe head 0 to 15,000 psi 4,470.00NISTPR44 NIST Traceable Certificate for Test Gauges 199.00NISTPR45 NIST Traceable Certificate with Data for Test Gauges 250.00

• Voltage and current measurement and sourcing• Optional software — Windows™-based SICAL software available for

remote operation and data transfer• RS232 communication link• Pressure switch test• Leak rate measurement from 1 second to 999 days• Display hold capability• Simultaneous display (pressure & electrical units)• Adjustable resolution

The PC6 PRO Series of pressure calibratorsutilizes the latest developments in pressure instrumentation to offer a versatile calibration instrument in a highly portable package. The PC6 PRO calibrator head can be supplied by itself or as a complete kit with pneumatic or hydraulic pump, NPT fittings, pressure hose and carrying case.

The compact size of the PC6 PRO does not compromise functionality. It can simultaneouslydisplay pressure versus voltage, current, date &time, percentage of pressure, pressure switch status, temperature, maximum or minimum values. Data can be logged and stored with timeand date stamping for future reference. Windowsbased SICAL software can be linked to the PC6PRO for remote operation and data transfer.

The base PC6 PRO offers very accurate pres-sure measurement along with current and voltagemeasurement and sourcing for calibration of pres-sure transmitters. PC6 IS is intrinsically safe.

NIST it



H

HTP1

LTP1

SPECIFICATIONS — HTP1Pressure Range

HTP1 - 700 0 to 700 bar/10,000 psiHTP1 - 1000 0 to 1000 bar/15,000 psi

Pressure Media Mineral based hydraulic oil or Distilled water (‘Skydrol’ and brake fluid available HTP1-S)

Pressure Connections 3/8” BSP female indication, 1/4” BSP female (process), 1/4” NPT female adapters

Weight 3.5 lb.Volume 100cc

SPECIFICATIONS — TP1Output Output pressure Output vacuum

TP1-25 0 to 25 bar/360 psi 0 to -0.8 bar/0 to -24”HgTP1-40 0 to 40 bar/600 psi 0 to -0.9 bar/0 to -28”Hg

Materials Bright nickel plated brass, clear anodized aluminum

Adjustment Fine volumetric pressure/vacuum adjusterWeight 1.5 lb.

SPECIFICATIONS — LTP1Output Pressure 0 to 2 bar/30 psiOutput Vacuum 0 to -850 mbar/0 to -25”Hg Materials Bright nickel plated brass, clear anodized

aluminumAdjustment Fine volumetric pressure/vacuum adjuster with

0.1 mbar / 0.00145 psi sensitivityWeight 1.5 lb.

• Hand-held pressure or vacuum generation• Low-cost way to verify performance of

pressure instrumentation• Rugged and reliable design• Fine adjustment control• The most efficient pumps available

Davis Instruments offers the best selection ofhand-held, portable pumps — suppling pressuregeneration with standard fine-tuning adjust-ments and pressure relief valves. These pumpsare ideal for use with electronic calibrators, digi-tal indicators, analog gauges, pressure transmit-ters, transducers, relief valves, or similar instru-mentation.

The rugged and reliable design of these pumpsand the fine adjustment controls added to theirdesign provides a low cost way to verify the per-formance of pressure instrumentation. Pumps canbe purchased independently, or in a kit includingcarrying case, NPT adapters, seals and hoses.

The HTP1 hydraulic pump is currently the onlyhand pump capable of generating pressure up to15,000 psi, utilizing hydraulic oil, Skydrol or dis-tilled water. The pump includes a unique highpressure or priming selector on the scissor actionpump mechanism, making pressure generationabove 5,000 psi easier.

The TP1 pneumatic pump generates pressureto 600 psi and vacuum to 28”Hg on the same unit.Made with no plastic parts these pumps are de-signed to endure harsh environments unlike ourcompetitor’s disposable models.

The LTP1 pneumatic pump also acts as a dualsource of pressure and vacuum over smallerranges making very fine adjustments easier. TheLTP1 range is 25”Hg vacuum to 30 psi, with0.00145 psi sensitivity.

Hand Pumps Pressure or Vacuum, Hydraulic or Pneumatic

Catalog No. Description PriceHTP1-700 Hydraulic pump, 10,000 psi $795.00HTP1-700-K 10,000 psi pump kit with carrying case, 7-piece adapter fittings and hose kit 1,295.00HTP1-1000 Hydraulic pump, 15,000 psi 995.00HTP1-1000-K Hydraulic pump, 15,000 psi 1,495.00TP1-25 Pneumatic pump & Vacuum, 360 psi to -24 inHg 395.00TP1-25-K 360 psi to -24 inHg pump & vacuum kit with carrying case, 7-piece adapter fittings and hose kit 550.00TP1-40 Pneumatic pump & vacuum, 600 psi to -28 inHg 595.00TP1-40-K 600 psi to -28 inHg pump & vacuum kit with carrying case, 7-piece adapter fittings and hose kit 750.00SI101 Pneumatic pump & vacuum, 30 psi to -25 inHg 495.00LTP1-K 30 psi to -25 inHg pump & vacuum kit with carrying case, 7-piece adapter fittings and hose kit 650.00HK1-1000 15,000 psi hose kit, with NPT adapters 295.00NISTPR44 NIST Traceable Certificate for Test Gauges 199.00NISTPR45 NIST Traceable Certificate with Data for Test Gauges 250.00

TP1

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

738

System 1:PneumaticHand pump

Precision Pressure Calibrators and Pumps

System 1 - PPC Electronic Pressure Calibrator with Pneumatic Hand PumpCatalog No. Model Range PriceAM760001 76-PPC-0001 0-30 inHg with T-750 Hand Pump $1,895.00AM760301 76-PPC-0301 0-30 PSI/0 to 25 inHg (0 to 2.000 bar) with 1,895.00

T-730 Hand PumpAM761001 76-PPC-1001 0-100 PSI/0 to 25 inHg (0 to 7.000 bar) with 1,895.00

T-740 Hand PumpAM762001 76-PPC-2001 0-200 PSI/0 to 25 inHg (0 to 15.00 bar) with 1,895.00

T-740 Hand PumpAM765001 76-PPC-5001 0 to 500 PSI (0 to 35.000 bar) with T-740 Hand Pump 1,895.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

System 2 - PPC Electronic Pressure Calibrator with Hydraulic Hand PumpCatalog No. Model Range PriceAM762002 76-PPC-20011 0-200 PSI/0 to 25 inHg (0 to 15.00 bar) $1,895.00

with T-620 Hand PumpAM765002 76-PPC-50011 0-500 PSI (0 to 35.000 bar) with T-620 Hand Pump 1,895.00AM761002 76-PPC-1K11 0-1000 PSI (0 to 70.00 bar) with T-620 Hand Pump 1,895.00AM7620021 76-PPC-2K11 0-2000 PSI (0 to 140.00 bar) with T-620 Hand Pump 1,895.00AM7650021 76-PPC-3K11 0-3000 PSI (0 to 200.00 bar) with T-620 Hand Pump 2,195.00AM7650051 76-PPC-5K11 0-5000 PSI (0 to 350.00 bar) with T-620 Hand Pump 2,195.00NISTPR44 — NIST Traceable Certificate for Test Gauges 199.00NISTPR45 — NIST Traceable Certificate with Data for Test Gauges 250.00

System 1This ready-to-use calibration system includes the Model PPC Indicator

with an T-730, T-740 or T-750 pneumatic hand pump as a precision pressuresource. Units may be supplied with NIST data if required. A 0 to 500 PSIunit is not available with vacuum pump option.

System 2This ready-to-use calibration system includes the Model PPC

Indicator with T-620 hydraulic hand pump as a precision pressuresource. Units may be supplied with NIST data if required.

System 2:HydraulicHand pump

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

System 3:Screw pump

System 4:Hydraulic pump

ElectronicPressureCalibrator

System 3 - PPC Electronic Pressure Calibrator with Hydraulic Hand PumpCatalog No. Model Range PriceAM765003 76-PPC-500111 0-500 PSI (0 to 35.000 bar) with Hydraulic Screw Pump $2,495.00AM761003 76-PPC-1K111 0-1000 PSI (0 to 70.00 bar) with Hydraulic Screw Pump 2,495.00AM762003 76-PPC-2K111 0-2000 PSI (0 to 140.00 bar) with Hydraulic Screw Pump 2,495.00AM763003 76-PPC-3K111 0-3000 PSI (0 to 200.00 bar) with Hydraulic Screw Pump 2,695.00AM7630031 76-PPC-5K111 0-5000 (0 to 350.00 bar) with Hydraulic Screw Pump 2,695.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

System 3This ready-to-use calibration system

includes the Model PPC indicator with ahydraulic screw pump as a precisionpressure source. A screw pump for waterapplications is optionally available.Units may be supplied with NIST data if required.

System 4 - PPC Electronic Pressure Calibrator with Hydraulic Hand PumpCatalog No. Model Range PriceAM761004 76-PPC-1K1V 0-1000 PSI (0 to 70.00 bar) with Type T Pump $3,995.00AM762004 76-PPC-2K1V 0-2000 PSI (0 to 140.00 bar) with Type T Pump 3,995.00AM763004 76-PPC-3K1V 0-3000 PSI (0 to 200.00 bar) with Type T Pump 4,295.00AM765004 76-PPC-351V 0-5000 PSI (0 to 350.00 bar) with Type T Pump 4,295.00AM76104 76-PPC-10K1V 0-10,000 PSI (0 to 700.00 bar) with Type T Pump 4,295.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

System 4This ready-to-use calibration system

includes the Type T hydraulic pump as aprecision pressure source. A pump forwater applications is optionally avail-able. Units may be supplied with NISTdata if required.

The Model PPC Electronic Pressure Calibrators are portable, self-contained instru-ment designed especially for accurate, convenient calibration of electronic pressuretransmitters, transducers, switches, gauges and other pressure measuring instruments.The PPC calibrator may be specified with an accuracy of ±0.05% of Full Scale ±1 LSD.

The PPC calibrator consists of a pressure indicator and a user-specified pressuresource.

The instru-ments feature instant conver-sions of pressurereadings to othercommon units ofmeasure, e.g.,bar, kPa, in.H2O, etc.

Catalog No. Model Description PriceAM75030 76-PPC-030 Pressure Calibrator (0-30 PSI) $1,595.00AM75100 76-PPC-100 Pressure Calibrator (0-100 PSI) 1,595.00AM75200 76-PPC-200 Pressure Calibrator (0-200 PSI) 1,595.00AM75500 76-PPC-500 Pressure Calibrator (0-500 PSI) 1,595.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

740

Combines the accuracy of a laboratory instrument with the functionality andportability of a field calibrator

Pressure Calibrators, Handpumps & Test Gauges

• ± 0.05% Accuracy of reading traceable to NIST• UL and c-UL Division 1, Class 1, Group C, D and Cenelec EEx ib IIB

T3 (179°C) Intrinsic Safety Approved, CE Mark Compliant• Modular, Interchangeable Pressure Ranges up to 2,000 psi (135 bar)• Current, Voltage & Pressure Switch Test Inputs• 5-Digit Floating Point Readout• Displays in English, Metric or S.I. units• Displays mA converted to pressure range and percent difference• Displays information in English, Spanish, French, German or Italian

The EPC 2000 Electronic Pressure Calibratorcombines the accuracy of a laboratory instrumentwith the functionality and portability of a field calibrator.

The EPC 2000 Calibrator is used to calibratepressure measuring instruments with an accuracyof ±0.005% of indicated readings from 20-100% offull scale. The EPC 2000 Calibrator is accurate to±0.025% of full scale at or below 20% of fullscale.The EPC 2000 calibrator is ideal for difficultapplications such as custody transfer stations, criti-cal process control applications and virtually anyapplication that requires near deadweight accuracy.

SPECIFICATIONSPressureRanges 0-100 in H2O

0-280 in H2O0-100 psi0-500 psi0-1000 psi0-2000 psi

Units of Measure psi, Torr, atm, kPa, mPa, mbar, bar, mmH2O @ 4°C, mmH2O @ 20°C, mH2O @ 4°C, mH2O @ 20°C, mmHg@ 0°C, kg/cm2, inH2O @ 4°C, inH2O @ 20°C, inH2O @60°F, ftH2O @ 4°C, ftH2O @ 20°C, ftH2O @ 60°F,inHg @ 0°C

Media compatibility Any media compatible with 316L stainless steel and Hastelloy C276Connection 0.25-inch female NPTCurrent Range 0-50mACurrent Format Options mA, mA to % mA to pressureCurrent Connections Standard banana jack, 0.75-inch centersVoltageRange 0-50 VDCFormat Options V, V to %, V to pressureConnections Standard banana jack, 0.75-inch centersSwitch TestDisplay shows closing and opening pressures simultaneouslyConnections Standard banana jack, 0.75-inch centersOperating temperature 32°F to 122°F (0°C to 50°C)Battery types Two 9V UL-approved Lithium Batteries (standard), 9V NiCd Battery pack (optional)Battery lifeStandard 9V Lithium 4 hours at 25°C typicalOptional 9V NiCd 3.5 hours minimum @ 32°F to 122°F (0°C to 50°C)Battery Charging Times (Approximate)120VAC Wall Charger 12 hours230VAC Wall (Euro Two Prong) Charger 6 hours12VDC Automotive Charger 1.5 hours120VAC Wall Adapter/12VDC Auto Charger 1.5 hoursWeight 2.34 lbs (1.06 kg)



H

NIST it

SPECIFICATIONSAccuracy ± 0.5% of gauge spanOperating Pressure 200 psig max.Wetted Parts Aluminum, brass, stainless steel, nylon® and

Nylatron GS*“O” Rings Buna-NTest Connection 1⁄4" NPT, 24" long hoseWeight 3 lbs.

The T-730 & T-740 testers feature a ruggedpneumatic pump to generate test pressures up to200 psig for pressure instrument calibration.This compact, lightweight device can be easilyoperated in the field or test stand mounted in theinstrument shop. These testers feature a new ex-tended range vernier adjustment for fine controlof pump pressure.

Pneumatic Hand Pump

Catalog No. Model Description PriceAM112 EPC-1-12/C EPC 2000 Electronic Calibrator 0-100 in H2O Single Range $2,395.00AM123 EPC-1-23/C EPC 2000 Electronic Calibrator 0-280 in H2O and 0-100 psi Dual Range 2,395.00AM126 EPC-1-26/C EPC 2000 Electronic Calibrator 0-280 inH2O and 0-2000 psi Dual Range 2,395.00AM134 EPC-1-34/C EPC 2000 Electronic Calibrator 0-100 psi and 0-500 psi Dual Range 2,395.00AM1461 EPC-1-46/C EPC 2000 Electronic Calibrator 0-500 psi and 0-2000 psi Dual Range 2,395.00NISTPR44 — NIST Traceable Certificate for Electronic Calibrator 199.00NISTPR45 — NIST Traceable Certificate with Data for Electronic Calibrator 250.00AccessoriesAM900201 T730 Pump Only (for range 0 to 30 psi) 291.00AM900202 T-740 Pump Only (for range 0 to 200 psi) 285.00AM620423 136893 3” Test Gauge 0-300” H2O 136.00AM620424 47864 3” Test Gauge 0-5 psig 136.00AM620425 47865 3” Test Gauge 0-10 psig 136.00AS10841 1084 3” Test Gauge 0-15 psig 136.00AS10842 1084 3” Test Gauge 0-30 psig 136.00AS10843 1084 3” Test Gauge 0-60 psig 136.00AS10844 1084 3” Test Gauge 0-100 psig 136.00AS10845 1084 3” Test Gauge 0-150 psig 136.00AS10846 1084 3” Test Gauge 0-200 psig 136.00AM620105 T-663 Carrying Case 69.00NISTPR44 — NIST Traceable Certificate for Test Gauges 199.00NISTPR45 — NIST Traceable Certificate with Data for Test Gauges 250.00

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

742

Precision Digital Pressure Calibrator

Catalog No. Description PriceSI300 Pressure Calibrator, -30" Hg (vac) to 30 psi, 1/4" NPT process connection $2,495.00SI301 Pressure Calibrator, -30" Hg (vac) to 150 psi, 1/4" NPT process connection 2,495.00SI302 Pressure Calibrator, -30" Hg (vac) to 300 psi, 1/4" NPT process connection 2,495.00SI303 Pressure Calibrator, 0 to 600 psi, 3/8" NPT process connection 2,495.00SI304 Pressure Calibrator, 0 to 5000 psi, 3/8" NPT process connection 2,495.00SI305 Pressure Calibrator, 0 to 10,000 psi, 3/8" NPT process connection 2,495.00NISTPR5 NIST Traceable Certificate 85.00NISTPR6 NIST Traceable Certificate with Data 130.00

• Pressure measurement range -29" Hg to 15,000 psi• Voltage and current measurement• Software Included• Simultaneous display of pressure and selected function• Timed/Event data storage with date & time stamping• RS232 data communication link• Pressure switch test• Leak rate measurement 1 second to 999 days• Maximum and minimum pressure measurement• Display hold facility• Supply output for transducer/transmitter• Tare pressure offset values• Pressure module temperature measurement• Adjustable resolution• External pressure module (EPM) interchangeability for required

pressure ranges

SPECIFICATIONSModel Range (psi) Overload Pressure (FS) Accuracy (FS) Resolution (FS) Better thanPC6-2-C -30" Hg to 30 psi 10% 0.05% 0.01%PC6-10-C -30" Hg to 150 psi 10% 0.05% 0.01%PC6-20-C -30" Hg to 300 psi 10% 0.05% 0.01%PC6-40-C 0 - 600 psi 10% 0.05% 0.01%PC6-350-C 0 - 5,000 psi 10% 0.05% 0.01%PC6-700-C 0 - 10,000 psi 10% 0.05% 0.01%PC6-1000-C 0 - 15,000 psi 10% 0.05% 0.01%Other Pressure Ranges are available to special order.Pressure units lb/in2, in H2O, in Hg, mm HgOverload Warning Flashing display and audible tone at 110% of FSTemperature Display Indicates temperature of pressure sensor moduleDC Input Range Resolution Accuracy Input resistanceVoltage measurement mV 0 to 100mV 1 uV 0.05% FS >1 MΩ

V 0 to 5V 0.1mV 0.05% FS >1 MΩAuto-range 0 to 50V 1mV 0.05%FS >1MΩ

Voltage Output Regulated DC supply 10V ± 0.1% max. current 30mA Unregulated DC supply 24V ± 10% max. current 30mADisplay Backlit LCD, 16 characters, 2 line alpha numericPressure Media Water, Oil, Non-corrosive gasesPressure Switch Test Indicates OPEN or CLOSEDOperating Temperature 32°F to 104°FCalibration Temperature 68°F ± 1°FCalibrated Temp. Range 50°F to 104°FRS232 Parameters Baud rate 110, 300, 1200, 2400, 4800, 9600, stop bits 1 or 2, status ON or OFFData Capacity 176 records into a maximum of 20 files, 8k memory (additional 204 records, 8k memory option available)Humidity 5 to 95% relative humidity non condensingResolution Select Increase or decrease by a factor of 10Power Supply 6V rechargeable battery/110 VAC operation via charger (supplied)Battery Life/Low Battery 10 Hours full charged/Continuous check, audio and visual warningDimensions/Weight 3.6" x 4.3" x 2.4" / 3.5 lbs.Pressure Connection 1/4" ISO male ‘quick-fit’ (Pneumatic) (NPT fittings provided) 3/8" ISO female ‘quick-fit’ (Hydraulic) (NPT fittings provided)

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Model CP-30 CAL-PAL® shownwith optional T-730 hand pump



H

Catalog No. Model Description PriceAM900101 CP-10 0-10 psig CAL-PAL® Digital Pressure Calibrator with test leads and soft case $950.00AM900102 CP-30 0-30 psig CAL-PAL® Digital Pressure Calibrator with test leads and soft case 950.00AM900103 CP-200 0-200 psig CAL-PAL® Digital Pressure Calibrator with test leads and soft case 950.00Hand Pumps (see page 417 for hand pump specifications)AM900201 T-730 0-30 psig Low Pressure Pneumatic Hand Pump 291.00AM900202 T-740 0-200 psig High Pressure Pneumatic Hand Pump 285.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

Precision Pressure Calibration SystemThe CAL-PAL® is a portable, self-contained instrument

designed specifically for accurate, convenient calibration ofelectronic pressure transmitters, transducers, switches,gauges, and other pressure measuring instruments. Whenused in conjunction with a portable hand held pressurepump, the CAL-PAL® is a complete, self-contained portablepressure calibration system.

The CAL-PAL® pressure calibration system measures anddisplays applied pressure as well as milliamp output signalof electronic transmitters or transducers under test. Displayindicates pressure in seven selectable units of measure;transmitter output signal is shown in milliamps or percent-age of 4-20 mA. A unique cycling circuit displays pressureand transducer output signals at four second intervals.

Pressure switches can be tested using a built-in contactclosure circuit which illuminates an LED indicator.

The CAL-PAL® can also be used as a precision digital testgauge to measure pressures with a high degree of accuracy.

The calibrator is supplied with two 9 VDC alkaline batter-ies to provide approximately 40 hours of operation. The CAL-PAL® comes complete with a cordura carrying case and threefoot test leads.

This compact, rugged, highly accurate, temperature compensated instrument is ideal for field use.

SPECIFICATIONSPressure RangeModel psi In. H2O In. Hg Bar kPa KG/CM2

CP-10 10 280 20 .70 70 .70CP-30 30 850 60 2.0 200 2.1CP-200 200 5500 400 14 1400 14Current Range 0 to 50 milliampsAccuracy ± .1% of full scale + 1 least significant digit, including linearity,

repeatability, and hysteresisResolution Four digits with floating decimal pointTemperature Range 30 to 130°F (0 to 55°C)Temperature Effect Not greater than .05% of full scale throughout the temperature rangeMedia Compatibility Air, nitrogen, water, natural gas, hydraulic oil, glycol

(consult factory for other media)Over Pressure “OV-Range” appears on display when pressure Indication reaches 110% of ratingOver Pressure This gauge is protected by a pre-set relief valveProtection Power Requirements Two 9VDC alkaline batteriesBattery Life Approximately 40 hoursLow Battery “LOW-BATT” appears on display periodicallyIndication Dimensions Approximately 6 7⁄8" H x 33⁄4" W x 2 5⁄8" DWeight Three poundsPressure Connection The input pressure connection is a 1⁄4" male NPT

NIST it

SPECIFICATIONS


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

744

Pressure Calibration Standard

• Three independent selectable ranges in each instrument• State of the art pushbutton calibration guarantees 0.05% accuracy

of each range• Three different technicians can calibrate the same transmitter and

get identical results...every time!• Portable—less than 30 pounds• Adjustable overpressure protection• Precision pressure vernier control• Pressure resolution of 0.02% F.S. typical for each range• Self-contained 2215 psi nitrogen cylinder• Easy to operate, train in ten minutes• Voltage/current display mode for transducer testing• Supplies 24 volt DC loop power• Quick disconnect fittings and hoses, supplied for input and output

pressure control• Users include: aircraft manufacturers, national government

laboratories, oil companies, electric power plants (nuclear & fossil)and general industry

• Calibration Traceable to the National Institute of Standards andTechnology

A 0.05% Pressure Standard, totally self-contained with its own 2215 psi pressure source!

Pressure Ranges + 0-30" Hg, + 0-400" H2O, + 0-100 kPa, + 0-2700" H2O, 0-100 psiAvailable Pressure Gauge and VacuumCalibrationOverall Accuracy ± 0.05% F.S. Accuracy of each range. Accuracy statement includes

all effects of linearity, hysteresis, repeatability and ambient temperature.

Operating + 40 + 1400°F Temperature RangeStorage 0 to 185°FTemperature RangeRelative Humidity 95% non-condensingPressure Media N2 or Shop AirPressure Media FilterRating 7 microns nominalType Field replaceable filter cartridgeControl ValvesType Micro-metering with positive shut-off, adjustable stop and

replaceable seat, non-destructible.Material Aluminum/Stainless SteelInternal PipingTubing 5⁄32" Nylon Tubing, 1⁄8" CopperFittings BrassTest PortStyle Quick disconnect type.Pressure Rating 600 psi max, connected or disconnectedPressure HoseQuality Supplied One (1) outputLength 5 feet, nominalVernier ControlVolume 0.25 cubic inchesMaterial Aluminum/Stainless SteelPressure Limit Monitor GaugeSize 2.0 inch diameterRange 160 psiPressure Supply Gauge 3000 psiRegulator 100 psi max.Construction Self-relieving, single stage regulatorInternal Pressure SensorType Bonded, metal foil strain gaugeSensitivity 3 mV/V, nominalConstruction Completely welded, sealed stainless steel outer body

and pressure cavityExternal Carrying CaseType Aluminum Case with cover and carrying handleMaterial Thickness 0.090 inch nominalFinish Gray Polyurethane baked enamel paint, textured finishWeight Less than 30 pounds, including 2 hoses and 1 cable.Size 10" wide by 16" long x 11.5" high (excluding handles)Current Display

0-20,000 mA counting by 0.005 mAVacuum Converter Capable of generating 27" Hg vacuum stand alone or 30" Hg with

external vacuum pumpWeight Less than 30 pounds including oil hoses and cable

Catalog No. Description PriceEA55478 Pressure Calibrator, 115 VAC & internal $6,995.00

rechargeable battery, 2000/1000/400 psi, gage, LED Display

EA61624 Pressure Calibrator, 115 VAC & internal 6,995.00rechargeable battery, 2000/1000/400 psi, gage, LCD Display

EA55819 Pressure Calibrator, 115 VAC & internal 6,995.00rechargeable battery, 1000/500/200 psi, gage, LED Display

EA61675 Pressure Calibrator, 115 VAC & internal 6,995.00rechargeable battery, 1000/500/200 psi, gage, LCD Display



EA61634 Pressure Calibrator, 115 VAC & internal 6,995.00rechargeable battery, 2000/1000/400 psi, gage or absolute, LED Display

EA61636 Pressure Calibrator, 115 VAC & internal 6,995.00rechargeable battery, 2000/1000/400 psi, gage or absolute, LCD Display





Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it

SPECIFICATIONSPressure Ranges + 0-30" Hg, + 0-400" H2O, + 0-100 kPa, + 0-2700" H2O, 0-100 psiAvailable Pressure Gauge and VacuumCalibrationOverall Accuracy ± 0.05% F.S. Accuracy of each range. Accuracy statement includes

all effects of linearity, hysteresis, repeatability and ambient temperature.

Operating + 40 + 1400°F Temperature RangeStorage 0 to 185°FTemperature RangeRelative Humidity 95% non-condensingPressure Media N2 or Shop AirPressure Media FilterRating 7 microns nominalType Field replaceable filter cartridgeControl ValvesType Micro-metering with positive shut-off, adjustable stop and

replaceable seat, non-destructible.Material Aluminum/Stainless SteelInternal PipingTubing 5⁄32" Nylon Tubing, 1⁄8" CopperFittings BrassTest PortStyle Quick disconnect type.Pressure Rating 600 psi max, connected or disconnectedPressure HoseQuality Supplied One (1) outputLength 5 feet, nominal

Vernier ControlVolume 0.25 cubic inchesMaterial Aluminum/Stainless SteelPressure Limit Monitor GaugeSize 2.0 inch diameterRange 160 psiPressure Supply Gauge 3000 psiRegulator 100 psi max.Construction Self-relieving, single stage regulatorInternal Pressure SensorType Bonded, metal foil strain gaugeSensitivity 3 mV/V, nominalConstruction Completely welded, sealed stainless steel outer body

and pressure cavityExternal Carrying CaseType Aluminum Case with cover and carrying handleMaterial Thickness 0.090 inch nominalFinish Gray Polyurethane baked enamel paint, textured finishWeight Less than 30 pounds, including 2 hoses and 1 cable.Size 10" wide by 16" long x 11.5" high (excluding handles)Current Display

0-20,000 mA counting by 0.005 mAVacuum Converter Capable of generating 27" Hg vacuum stand alone or 30" Hg with

external vacuum pumpWeight Less than 30 pounds including oil hoses and cable



H

Pressure and Vacuum Calibration StandardOne instrument does it all! Calibrate from 30" Hg vacuum to 100 psig pressureA ±0.05% Pressure Standard, totally self-contained with its own Pressure andVacuum source!

• Five independent selectable ranges ineach instrument

• ± 0.05% F.S. accuracy for each range• State of the art pushbutton calibration!

Guarantees to ± 0.05% accuracy for eachrange. No analog potentiometers or adjust-ments required!

• Three different technicians can calibratethe same transmitter and get identicalresults...every time!

• Easy to operate, train in ten minutes• Users include aircraft manufacturers,

national government laboratories, oil com-panies, electric power plants (nuclear andfossil) and general industry

• Only one box to carry, self containedenclosure with carrying handles

• Lightweight—less than 30 pounds• Adjustable overpressure protection• Precision vernier control• Display resolution of 0.02% F.S. typical for

each range• Self-contained nitrogen cylinder and vacu-

um converter provides 27" Hg (withoutexternal pump) to 100 psi

• Traceable to the National Institute ofStandards and Technology

• Voltage/current display mode for transducer testing

• Quick disconnect fitting and hose suppliedfor output connection


EA117435 UPC5700BA AC Power Pressure Standard, LED Diaplay with rechargeable internal battery $6,995.00

EA117436 UPC5700BB AC Power Pressure Standard, LCD Display with rechargeable internal battery 6,995.00

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

746

Portable Pneumatic Pressure Calibrator

Design and ConstructionThe Series 6512000 Portable Pneumatic Calibrator is a

pressure-vacuum test stand wholly contained in a carryingcase. The front panel accommodates the precision pressuregauge, all pressure connections, two air-regulator controls, anda selector valve. With the selector valve, three different testpressures can be applied individually to the gauge. A fourth se-lector setting vents the gauge to atmosphere.

The precision pressure gauge has a Ni-Span C, capsule-typepressure element which gives excellent temperature stabilityand speed of response. An almost frictionless mechanical link-age amplifies capsule movement and transmits it to the point-

er. Although highly sensitiveand accurate, the mechanismis built to withstand the han-dling normally associatedwith on-site calibration ofpneumatic instrumentation.

A filter on the air supplykeeps oil and moisture out.Two regulators apply knownpressures to the devices un-der test. The connectionblock has 1⁄8 inch female-pipethreaded connections. Small

gauges can be threaded directly into the block; or as with larg-er instruments, connected by flexible tubing.

The scale contains two sets of calibrations: -100 to 0 to 850inches of water and -3.6 to 0 to 30.6 psi.Clear, Accurate Readout

Sharply defined graduations, a 45-inch scale length overtwo pointer revolutions, and a knife edge pointer to facilitateprecise readouts. All scale calibrations are individually plottedand hand marked to produce a dial custom fitted to the pres-sure element and mechanism of that gauge.Engineered for Performance

The gauge housing is heavy cast aluminum with a tem-pered glass dial cover. A built-in pressure-relief valve has adumping capacity which protects the case against overpres-sure to 10 times the maximum pressure rating. A separatepressure-relief valve protects the capsule mechanism. Thegauge is mounted inside the carrying case on rubber-paddedshock mounts. The carrying case is constructed of strong butlightweight molded ABS that flexes to absorb shock from im-pact.Compact, Built for On-Site Service

The Portable Pneumatic Calibrator weighs only 20 lbs. andis only slightly larger than an attache case. The easy portabili-ty, simple set-up and the versatile capabilities of this unit ex-tends its usefulness for service in the field. Its portabilitysaves the time and expense of shop calibration.

• Calibration of Pressure Transmitters

• Calibration of Gauges, Indicators &Recorders

• Calibration of Differential PressureTransmitters

• Calibration of Ratio Relay

• Calibration of Typical StackedDiaphragm pneumatic controller


WT555600 6512000 Portable Pneumatic Pressure Calibrator $2,875.00NISTPR44 — NIST Traceable Certificate 199.00NISTPR45 — NIST Traceable Certificate with Data 250.00

An Extra Measure of AccuracyAll Portable Pneumatic Calibrators are subjected to rigor-

ous and extensive testing. Each has to perform at better thanthe rated accuracy (0.1% of full scale) to be accepted. It’s accu-rate enough to double as a shop standard.Calibration Traceable to NIST

Calibration is with primary standards which are directlytraceable to the National Institute of Standards and Technology.

•Gauge Pressure:Test pressure is applied to the capsulethrough the appropriate P connection; thecase is open to atmosphere through S

•Differential Pressure:High test pressure is applied to the capsulethrough the appropriate P connection. Lowtest pressure is applied to the case through S

•Absolute Pressure:Test pressure is applied to the capsulethrough the appropriate P connection andthe case is continuously subjected to fullvacuum through S

•Vacuum:The capsule is open to atmospherethrough connection P; the case is connect-ed to test vacuum at S

•Positive and Negative Pressures:Test pressure is applied to the capsulethrough the appropriate P connection andthe case is open to atmosphere through S

SPECIFICATIONSRange and On the dial, the outer scale reads -100 to 0 to 850 inches of water Calibration with graduations every 1.0 inch; the inner scale reads -3.6 to 0 to

30.6 psi with graduations every 0.05 psi.Accuracy 0.1% full scaleRepeatability 0.03% of full scaleSensitivity 0.01% of full scaleHysteresis 0.1% of full scaleReadability 0.02% of full scaleTemperature effect Maximum is 0.1% of full scale per 10 C change from 25 CScale Length 45 inches through 2 pointer revolutionsOverpressure A pressure relief valve protects the mechanism (capsule); Protection pressure up to 90 psi will not damage the mechanism or affect

accuracy. A built-in relief valve and a flow restricter protect the case from pressures up to 10 times the case rating of 35 psig. This valve is an emergency-protective device only

Maximum Case Will not exceed 1.03 x 10 7 std cc/sec. or 0.018 psi/hrLeak RateMaterials Exposed Capsule system: Ni-Span C; soft solder; brass; 303 stainless steel; to Measured Gas silver solder

Case system: Ni-Span C; brass; phosphor bronze; beryllium copper, magnesium, nylon®, aluminum, 303 stainless steel; Elgiloy; soft solder, silver solder, HypalonInlet manifold to pressure gauge: aluminum; brass polyethylene; copper; steel; glass wool; carbon; Buna N

Gauge Case Anodized aluminum with tempered glass dial coverCarrying Case ABS plastic 171⁄2 in. x 12 in. x 71⁄2 in.Accessories 6 adapters for 1⁄8" pipe thread to 1⁄4" plastic tubing, 20 ft. of 1⁄4"

OD plastic tubing, instruction book, sheet with summary of important instructions

Modifications Other ranges (to 0-100 psi) and other units of calibration including metric (SI) units, are available at extra cost

Shipping Weight 50 lbs. (20 lbs. net)Note: Calibrator is for use with non-corrosive gases. It should not be used with liquids.

NIST it



H

Digital Pneumatic Calibrator

Catalog No. Description PriceWK001 MATRIX Digital Pneumatic Calibrator $2,295.00NISTPR44 NIST Traceable Certificate 199.00NISTPR45 NIST Traceable Certificate with Data 250.00

NIST it

The MATRIX Digital PneumaticCalibrator features high accuracy, compactdesign, and a variety of calibration func-tions. The MATRIX has a digital accuracy of±0.05% of span. It also incorporates mA andV inputs, and it has a built-in 24 Volt looppower supply to simultaneously power a de-vice while reading the resultant current.

The MATRIX is designed primarily for ac-curate and convenient calibration of pneu-matic controls and instrumentation. Theportable design allow for ease of calibrationin the field. In most cases, the device beingchecked does not need to be removed from itsservice location.

SPECIFICATIONSAccuracy ± 0.05% of full scaleDisplay 16 x 2 Line Dot MatrixModes of Operation Gauge, Differential, Vacuum (PressureMeasurements) (Vacuum to -5 PSI)Power Supply In: 115 volt AC or built-in NiCad batteries

Out: 24 VDCAir Supply Maximum input pressure is 90 PSI,

Pressure connections are 1/8" female NPTMaximum Differential Pressure 90 PSI on P3 port with 35 PSI on S portTemperature Operating Range 0°C to 50°CStandard RangesUnits Pressure RangesPSI -5 to 30kPa -34.47 to 206.80kg/cm2 -0.3515 to 2.1090inH2O (4 deg C) -138.4 to 830.4inH2O (60 deg F) -138.5 to 831.2cmH2O -351 to 2,109mmH2O -3,510 to 21,090BAR -0.3447 to 2.0680mmHg -258.6 to 1,551mA 0 to 24Volts 0 to 20

• Portable, easy to set up and connect• Calibrates pneumatic and electro-pneumatic instrumentation in

service• High accuracy: ± 0.05% of full scale• Measures gauge, differential, or absolute pressure by simply changing

connections• Measures current or voltage at the flip of a switch• Operates on 115 volts or rechargeable AA batteries

Pressure CalibratorsThis calibrator allows a technician

to test the output or differential pres-sure (flow) readings of a pneumaticinstrument with one hand allowingthe other hand to make calibrationadjustments on the instrument beingtested. The calibrator weighs only 8oz. as compared to 3 or more lbs. forequipment marketed in kit form orone made up by the technician fromparts.

The calibrator consists of sphyg-momanometer-type (blood pressure)gauge accurate to 1% with a squeeze

bulb for applying pressure manuallyand a precision-machined hand-ad-justed valve to hold and relieve thecalibrating pressure. A flexible hoseand a 3⁄16" tube-1⁄4" NPT compressionfitting is supplied for quick and easyconnection to unit being tested.

Catalog No. Model Description PriceTA163771 44S369 0 to 160" Water Calibrator with case $235.00TA163772 44S390 0 to 18 psig Calibrator with case 240.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

• Pneumatic Controllers• Low Pressure Gauges• Pneumatic Transmitters• Flow Transmitters

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

748

SPECIFICATIONSPRESSURE GAUGE

Accuracy ± 1.5% range (44S369), within 1% of range span(44S390)Range 0 to 300" H2O (all); 0 to 15 psi (Model C-101);

0 to 30 psi (Model C-102)Pointer Adjustable, knife edge, black finishCase Nickel-plated brass, polishedWindow Glass with polished, beveled edges providing parallax-free

pointer viewing on flat and beveled surfacesTUBING Black Rubber; 18" long input, 36" long output (C-101 & C-102)PRESSURE BULB High volume with integral check and bleed valvesFITTINGS Quick disconnect with 1⁄4" NPT male and

1⁄4" NPT female adapters

Catalog No. Model Description PriceAM900301 C-100 Low Pressure Kit, 0 to 300" H2O $394.00AM900302 C-101 Low Pressure Kit, 0 to 300" H2O & 0 to 15 psi 730.00AM900303 C-102 Low Pressure Kit, 0 to 300" H2O & 0 to 30 psi 568.00NISTPR501 — NIST Traceable Certificate for C-100 85.00NISTPR511 — NIST Traceable Certificate with Data for C-100 135.00NISTPR5 — NIST Traceable Certificate for C-101 & C-102 85.00NISTPR6 — NIST Traceable Certificate with Data for C-101 & C-102 130.00

Low Pressure CalibratorsHighly accurate

NIST it

Includes:• Test gauge• Tubing• Squeeze bulb• 1⁄4" NPT fittings• Carrying case

Pressure Test Pump10,000 psi/15,000 psi Hydraulic Pressure (oil or water)

Catalog No. Description PriceSI1700 Hydraulic Hand Pump (0 to 10,000 psi) $795.00SI1701 Service Kit for HTP1 75.00SI1100 Hydraulic Hose kit for HTP1 (1/4" NPT female gauge adaptor) 295.00SI11000 Hydraulic Hand Pump (0 to 15,000 psi) 995.00SI11001 Service Kit for HTP1 75.00SI11002 Hydraulic Hose Kit for HTP1 (1/4" NPT female gauge adaptor) 295.00NISTPR44 NIST Traceable Certificate 199.00NISTPR45 NIST Traceable Certificate with Data 250.00

• Hydraulic Pressure to 10,000 psi/15,000 psi• Sealed Construction, No Leaks! No Rust!• Lightweight, hand held and easy to use• Quick priming and pressure generation• Vernier fine adjust

• Large see-through reservoir with a capacityof over 4 oz.

• Compatible with many different liquids. e.g.mineral oil, distilled water

• 3/8" ISO (NPT provided) female

NIST it

Use these portable, lowpressure test kits, to checkthe accuracy of differentialpressure recorders, indica-tors, and transmitters.Available in three models,C-100, C-101 and C-102,these instruments featurediaphragm actuated 3" di-ameter 0 to 300" test gaugesthat measure inches of wa-ter with an accuracy of±1.5% full scale.



H

Pneumatic Hand Pumps

Vacuum Hand Pump

SPECIFICATIONSAccuracy ± 0.5% of gauge spanOperating Pressure 200 psig max.Wetted Parts Aluminum, brass, stainless steel, nylon® and

Nylatron GS*“O” Rings Buna-NTest Connection 1⁄4" NPT, 24" long hoseWeight 3 lbs.

Catalog No. Model Description PriceAM900201 T-730 Pump Only (for range 0 to 30 psi) $285.00AM900202 T-740 Pump Only (for range 0 to 200 psi) 285.00Optional GaugesAM620423 136893 3" Test Gauge 0-300" H2O 225.00AM620424 47864 3" Test Gauge 0-5 psig 225.00AM620425 47865 3" Test Gauge 0-10 psig 225.00AS10841 1084 3" Test Gauge 0-15 psig 155.00AS10842 1084 3" Test Gauge 0-30 psig 155.00AS10843 1084 3" Test Gauge 0-60 psig 155.00AS10844 1084 3" Test Gauge 0-100 psig 155.00AS10845 1084 3" Test Gauge 0-150 psig 155.00AS10846 1084 3" Test Gauge 0-200 psig 155.00AM620105 T-663 Carrying Case 80.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

SPECIFICATIONSAccuracy ± 0.5% of gauge spanRange 0 to 25" of mercury vacuumWetted Parts Aluminum, brass, stainless steel, nylon® and

Nylatron GS“O” Rings Buna-NTest Connection 1⁄4" NPT, 24" long baseWeight 3 lbs.

The T-730 & T-740 testers feature a rugged pneumatic pump to generate testpressures up to 200 psig for pressure instrument calibration. This compact, light-weight device can be easily operated in the field or test stand mounted in the in-strument shop. These testers feature a new extended range vernier adjustmentfor fine control of pump pressure.

Catalog No. Model Description PriceAM9003011 T-750 Vacuum Pump (without gauges) $315.00AS199100 1084 3” Test Gauge, 0-30" Hg Vacuum 136.00AM620105 T-663 Case 80.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

NIST it

NIST it ™

The T-750 tester is a unique vacuum type device for testing andcalibration of vacuum instruments in ranges up to 25" Hg VAC.This device incorporates the same features as the hydraulic andpneumatic models; 3" precision test gauge with swivel fitting,vernier adjustment, shut off valve, pistol grip handle, etc.

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Pneumatic Hand Pump with Gauge (sold seperately)


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

750

Hand Pumps and Digital Test Gauge/Calibrator

Catalog No. Model Description PriceTD100 8110-300 0-300 psig Pneumatic Hand Pump (without Test gauge) $400.00TD2000 8112-3000 0-3000 psig Hydraulic Hand Pump (without Test gauge) 675.00TD1000 8111-300 -13.7-300 psig Duplex Hand Pump (without Test gauge) 570.00Optional Digital Test Gauges/CalibratorsD6551415 65514-15B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-15 psig 595.00D6551421 65514-21B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-30 psig 595.00D6551423 65514-23B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-100 psig 595.00D6551426 65514-26B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-300 psig 595.00D6551427 65514-27B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-500 psig 695.00D6551429 65514-29B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-1000 psig 695.00D6551432 65514-32B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-2000 psig 695.00D6551433 65514-33B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-3000 psig 695.00D6551435 65514-35B55 Digital Test Gauge/Calibrator, -14.7 Hg Vac-5000 psig 745.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00

SPECIFICATIONSModel 8110-300 8111-300 8112-3000Pressure Range 0-300 psig 0-300 psig/0-25" Hg Vac 0-3000 psigWeight 1.3 lbs. (0.6 kg) 1.4 lbs. (0.65 kg) 1.75 lbs (0.79 kg)Dimensions (w/o Test gauge) 9.5" L x 5" W x 3" D 10" L x 5" W x 3" D 11.5" L x 5" W x 3" DTest Connections 1/4" NPT female 1/4" NPT female 1/4" NPT femaleMaterials of Construction Machined aluminum body, stainless steel shaft and needle valve, ABS plastic handles, brass connection tee and connector

- Hose Nylon Nylon braided metal - Seals Viton Viton Viton

Hydraulic Hand Pump Duplex Hand Pump

NIST it

Viton is a registered trademark of DuPont Dow Elastomers

• Versatile - Self contained pressure source for calibration of gaugesand switches

• Safe - No electrical power or high pressure bottles. Pressure tested to2x rated pressure

• Accurate — 1/4% full scale with the line of test gauges (optional)• Adjustable — Precision vernier provides for a wide range of pressure

adjustment• User friendly — Compact size and light weight• Easier to use — Low handle force at all pressures• Rugged — “Industrial strength” construction



H

Pneumatic Vacuum & Pressure PumpsThese economical, light-

weight pneumatic handpumpsgenerate test pressures up to100 psig for pressure instru-ment calibration and vacuumto 25 "Hg. This compact, light-weight unit can be easily oper-ated in the field and can bestored in a briefcase. The pumpis used by connecting 1⁄8" ODplastic tubing to the pump andthe other end to a referencegauge and the instrument un-der test. This tester features afine-tuning vernier adjustmentfor resolution within 1" H2Oand a thumbscrew bleed valvewhich allows rapid or verygradual venting of pressure.

Catalog No. Model Description PriceAM11810 T-810 Pneumatic Pressure Pump, 0-100 PSI $239.00AM11811 T-811 Pneumatic Vacuum Pump, 0-25 "Hg 239.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate with Data 130.00Units can only be NIST Certified if gauge is purchased along with pump.

Hydraulic Pump Calibrator & Fittings

Catalog No. Model Description PriceAM620101 T-620 Hand-Held Hydraulic Pump $230.00AS10851 1084 0 to 1000 psig Gauge 136.00AM620421 161956 0 to 2000 psig Gauge 136.00

Accuracy ± 1.0% FSAM620422 161957 0 to 3000 psig Gauge 136.00

Accuracy ± 1.0% FSAM620105 T-663 Carrying case 80.00NISTPR5 — NIST Traceable Certificate 85.00NISTPR6 — NIST Traceable Certificate 130.00

with Data

• Lightweight-ideal for field use. Handy carryingcase available

• Handle permits convenient test stand mounting• Needle valve for positive shut off• Pistol grip handle for quick, easy pump action

• Accuracy ± 0.5% F.S. with precision test gauge• Can be used to calibrate pressure transmitters,

gauges, transducers and other instruments• All testers provide vernier adjustment for fine

control of pump pressure

SPECIFICATIONSAccuracy ± 0.5% of gauge spanTest Fluid Petroleum based oils,

hydraulic fluidsOperating Pressure 3000 psi maximumWetted Parts Aluminum, brass, stainless steel

and Lexan“O” Rings Buna NReservoir Capacity 1 pintTest Connection 1⁄4" NPT, 24" long hose Weight 3.5 lbs.

NIST it

SPECIFICATIONSOperating Pressure 200psig maxWetted Parts Delrin, Stainless Steel, BUNA-NTest Connection 1⁄8 " FNPTSize 9 1⁄2 " length by 1 1⁄2 " diameterOptions O-Ring Repair Kit: 10' x 1⁄8 " OD

Plastic Tubing with (2) 1⁄8 " MNPT fittings and T-Fitting

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

752

SPECIFICATIONSPressure range 0 to 700 bar/ 0 to 10,000 psiAccuracy 0.05% FS combined non-linearity, hysteresis

and repeatabilityTemperature comp 0 to 50°CTemperature drift ± 0.02% FSTemperature range -10 to 50°CTest connection 1/4” BSP FemalePower supply One 9 volt batteryHours of operation 80 hoursWeight 17.5 lbsInterface RS232Oil volume 0.5LDelivery Carrying case, fittings, calibration certificate,

Pre-Cal software and instruction manual

• Accuracy and stability. High accuracy, to 0.05% due to improved thin film strain gauge transducer

• Reliable, rugged design. Built for reliable performance under the most severe conditions

• Portable. Light-weight, with no fragile reference gauges• Semi-automatic calibration with FREE PRE-CAL Windows™-based

software

The PC700 offers precision pressure calibrationin any environment. With the PC700, test pres-sure is easily generated by the built-in hydraulicpump and is read from a four-digit LCD display.Simply pump up to the desired pressure, fine tunewith the integrated verneir valve, and compareyour test instrument to the digital display.

The PC700 is an obvious choice for all of your insitu pressure calibration needs. It utilizes a spe-cial thin film strain gauge transducer with built-intemperature compensation. Because the thin filmstrain gauge is about 1/12 the thickness of a bond-ed strain gauge, it’s more flexible. Therefore, accu-racy, long-term stability, fatigue, and product lifeare all improved. Unlike some other pressure calibrators, accuracy is maintained when decreas-ing pressure, which makes it ideal for verifyinghysteresis. All units are calibrated in positive aswell as negative direction.

FREE Windows™ based PRE-CAL software canbe interfaced with the standard RS232 port forsemi-automatic calibrations and record keeping.

Pressure CalibratorRobust, Portable and Accurate Pressure Calibration up to 10,000 PSI

Catalog Number Description PricePC700-1K-0.05% Pressure calibrator, PC700, 1000 PSI, 0.05% accuracy $4,580.00PC700-2k-0.05% Pressure calibrator, PC700, 2000 PSI, 0.05% accuracy 4,580.00PC700-3k-0.05% Pressure calibrator, PC700, 3000 PSI, 0.05% accuracy 4,580.00PC700-5k-0.05% Pressure calibrator, PC700, 5000 PSI, 0.05% accuracy 4,580.00PC700-10k-0.05% Pressure calibrator, PC700, 10000 PSI, 0.05% accuracy 4,580.00

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it



H

Deadweight Test Kits

Portable Pressure Tester

The Model RK is a self-regulatingpressure standard designed for use inranges from 4" H2O through 300 psig.

An integral weight storage com-partment for ranges to 50 psig orequivalent is contained in a cast met-al base which houses the workings ofthe unit (additional weights forranges above 50 psig or equivalentare packaged in a separate carryingcase).

The tester comes with a carryingcover of high strength impact-resis-tant material. The tester base in-cludes a built-in mounting to fit moststandard photographic type tripods.

Catalog Model Range Minimum PriceNo. IncrementsAM900401 RK-300WC-SS 4-314' H2O 1" H2O $4,630.00AM900402 RK-1600WC-SS 4-1614" H2O 1" H2O 5,626.00AM900403 RK-100-SS 1-101 psi 1 psi 4,673.00AM900404 RK-300-SS 1-301 psi 1 psi 6,258.00NISTDW3 NIST Traceable Certificate with Data 595.00

The Model PKII is a self-regulating, portable,primary type pressure standard designed for usein ranges from 4" H2O through 30 psi. The PKH isself-contained in a rugged plastic case designedfor “closed-case” operation, eliminating wind prob-lems. The weights are stacked in foam pockets inthe case for convenient handling. Additional spaceis provided in the case and cover for accessoryequipment and tools.

SPECIFICATIONSAccuracy± 0.05%; optional accuracy .025% and .015% of indicated reading.Stainless steel weights. Calibrated for International Standard Gravity980.665 Gals. (cm/sec2) or user's local gravity.± 0.5%, with non-magnetic die cast alloy weights available as an economi-cal alternative in non-corrosive environments. Calibrated at U.S. MeanGravity 980.000 Gals. (cm/sec2) Repeatability .005% of output readingTemperature .00167% of output pressure per °C, based on 23°CCoefficientSupply Instrument quality air per ISA Quality Standard S7.3. Pressure Maximum: 100 psi. Minimum: 30 psi or 150% of output

pressure, whichever is greaterFlow Rate 1.0 SCFH at 4" H2O output, 11.0 SCFH at 30 psi outputCase Size 13 1⁄8" x 9 1⁄4" x 6 3⁄8" on 4"-104" H2O and 4"-254" H2O

testers, and 13 1⁄8" x 8 1⁄4" on 4"-854" H2O testers.Total Weight 14 to 23 lbs. (1⁄4" tube fitting)

Catalog Model Range Minimum PriceNo. IncrementAM900501 PKII-30-SS 1-30 psi 1 psi $4,434.00AM900505 PKII-304-WC 4-304 "w.c. 1" water 3,929.00NISTDW2 NIST Traceable Certificate with Data 495.00NISTDWQ2 2 Year NIST Traceable Certificate with Data 742.00

SPECIFICATIONSAccuracy ± 0.5% of indicated reading. Stainless steel weights;

calibrated for international standard gravity 980.665 Gals. (cm/sec2) or user's local gravity

Repeatability 0.005% of output readingTemperature 0.00167% of output pressure per °C, based on 23°CCoefficientSupply Instrument quality air per ISA Quality Standard S Pressure 7.3. Maximum: 450 psi Minimum: 30 psi or 150% of output

pressure, whichever is greaterFlow Rate 1 SCFH at 4" H20 output, 60 SCFH at 300 psi outputCase Size Tester: 15" x 9.5" x 8", Weights: 8.5" x 12" x 11.5"Total Weight Tester: 18 to 31.5 lbs., Weights: 17.5 to 61.5 lbs.Input & Output Connections 1⁄8" NPT femaleOptional Accuracy Available .025% and .015%

NIST it

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

754

Ashcroft Model 1305D deadweight testers pro-vide an easy means of precisely generating pres-sure to an accuracy of 0.1% of reading. 1305 unitsare available for operating ranges up to 10,000psi. They are ideal in use of calibrating, setting,testing, and repairing pressure measurement andcontrol devices. Each 1305D unit is traceable tothe National Institute of Standards andTechnology assuring instrument accuracy.

These pressure systems are designed to be fieldportable. A single carrying case holds the pressuregeneration pump as well as the necessary toolsand accessories. A second box contains the weightsused for pressure generation (10,000 units require2 boxes of weights).

Ashcroft deadweight testers qualify as primarystandards for pressure calibration.

The pump is a two-stage hydraulic pressuregenerator. A built-in shuttle valve allows for rapidpressure increase at low pressures. The rate of in-crease, at pump cycle, can be reduced at higherpressures in order to minimize resistance. This isaccomplished by simply repositioning the two po-

sition shuttle valve. Withthe shuttle valve in thehigh pressure position,increasing pressure evenwhen near the 10,000 psiupper limit can be quicklyand easily accomplished.Final, precise adjustmentis accomplished throughthe use of an integralvernier adjustment knob.

The 1305D is providedwith two piston cylinderassemblies: A low pres-sure piston for pressureranges from 15 to 2000psi and a high pressureunit for pressures from 75to 10,000 psi. The highpressure piston has anarea of 1⁄80th of a squareinch while the low pres-sure piston has an area of1⁄16th of a square inch.Weights are provided forpressure increments of 5,10, 20, 25, 40, 50, 100,200, and 500 psi (depend-ing on piston in use). Anoptional 1 psi incremen-

tal weight is also available. Ashcroft 1305Dtesters can be used anywhere within their opera-tional range without any change in accuracy. Thesame weights are used with both piston and cylin-der assemblies.

The 1305 units are available for psi, bar, kg/cm2

and kPa ranges. Each unit comes complete with ahand jack set (for removal of pointers on gaugesbeing calibrated), spare O-rings and all tools, accessories and fittings required for normal use.

Precision Deadweight Tester

Pressure RangeCatalog No. Model Description Low High Price

AS130200 1305D-10 Deadweight tester 15-200psi 75-1000psi $2,985.00

AS130201 1305D-20 Deadweight tester 15-400psi 75-2000psi 3,125.00



AS130204 1305D-100 Deadweight tester 15-2000psi 75-10,000psi 4,060.00NISTDW4 — NIST Traceable Certificate with Data 545.00

• Accuracy of 0.1% of reading• Operating pressure of 15 psi

to 10,000 psi(100 kPa to 70,000 kPa)

• Operating media1305D — SAE 20 weight automotive or machine oil1305DH — Phosphate or glycol based hydraulic fluids

• Traceable to NIST

• O-Ring material1305D-Buna-N (D series)1305DH- Ethylene propylene(DH series)

• Stainless steel piston andcylinder material

• Non-magnetic die-cast zincalloy weight material

• Reservoir volume approxi-mately 1.5 pints (0.7 liter)

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Hydraulic Deadweight Testers

Catalog No. Model Ranges Increments PriceAM900990 Type T-50 100 to 500 psi 5 psi $3,765.00

100 to 5000 psi 50 psi

AM900992 Type T-100 100 to 1000 psi 5 psi 4,238.00100 to 10,000 psi 50 psi

AM900994 Type T-150 100 to 1500 psi 5 psi 4,762.00100 to 15,000 psi 50 psi

NISTDW4 — NIST Traceable Certificate with Data 545.00

These hydraulic deadweight testers offer supe-rior accuracy for the calibration of gauges,recorders and indicators. The accuracy is ±.01% ofindicated value and is traceable to NIST.Type T

For use with distilled water or other fluids com-patible with 300 series stainless steel or monel.Suspended weights of a hard, non-magnetic diecast alloy. Type T oil models are for use with oil ashydraulic fluid

Kit includes:• Weight Set• Pump• Tool Set• Carrying Case

• Hand operated hydraulic pump,with manual dual volume controlvalve, delivers high volume torapidly build pressure and lowvolume for ease of pumping anda gradual approach to the pointof calibration

• Suspended weights-suspendedon a carrier tube to lower centerof gravity and reduce side thruston the measuring piston andcylinder assembly

• Re-entrant type measuring pis-ton and cylinder assembly-main-tains accuracy as test pressuresincrease. Piston/cylinder assem-bly is completely enclosed in aunique column design, reducingthe possibility of accidentaldamage

• Pressure vernier-Auxiliaryscrew type piston permits fineadjustment of pump pressure

SPECIFICATIONSAccuracy Standard-± 0.1% of indicated pressure traceable to NIST.

Calibration to ± 0.025% is available with data furnished certified traceable to NIST. Calibration data is determined by cross floating against a laboratory standard traceable to NIST.

Test Fluid Type T-distilled water and/or oilOperating Pressure Type T-15,000 psi max.Wetted Parts Type T-300 series SS and MonelO-Rings Standard-Buna N; Optional-Viton®, EPTTest Connections Union type- 1⁄4" NPT, 1⁄2" NPT, 7⁄16"-20 UNF

male and female)Weights 55 lbs.Dimensions Overall operating dimension-

31 1⁄4" long x 9" wide x 19 3⁄4" high max.Reservoir Capacity 75 cubic inchesApproximate Weight Tester & Carrying Case: 50 lbs.Weight Sets #1: 55 lbs., #2: 110 lbs., #3: 165 lbs.

NIST it



H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

756

• Ceramic nozzle and ball enabling-Wide operating temperature range-Enhanced cold-weather service-Reduced temperature sensitivity(0.00048%/°C)

• 400 psi overpressure protection preventsinternal damage

• Stainless steel weight carrier for betterstability

• Mass set and weight carrier designed forconvenient calibration steps

• Stainless steel leveling screws for betterdurability

• Exhaust vent discharges outside instrument case, reducing contamination

• Durable case, allowing operation with thelid closed to eliminate the effects of drafts

• Ease of maintenance features-Pipeline liquid contamination can beremoved on-site, avoiding costly returnsand failed site calibrations.-Air tanks are accessible for cleaning

• Rigid manifold connections prevent internal damage

• Tripod mountable

SPECIFICATIONSAccuracy 0.05%, 0.025%, 0.015% of reading traceable to NIST including linearity,

hysteresis, repeatability, and the reference standardTemperature Range 20 to 140°FInstrument Weight 17 lb to 26 lbInstrument Dimensions 14"L x 10"D x 7" HStarting Pressure 5 inH2OMinimum Weight Increment 5 inH2OGas SupplyPressure 35 psi minimum, 100 psi maximumFlow Rate 0.5-6 SCFHConnection PortsInlet 1⁄4 " NPTFOutlet 1⁄4 " NPTF

Pneumatic Deadweight Testers

Pressure Price Price Price Model Range Catalog No. Accuracy 0.05% Catalog No. Accuracy 0.025% Catalog No. Accuracy 0.015%T9000-100 5-100 inH2O DR9105 $3,387.00 DR91025 $3,786.00 DR91015 $4,226.00T9000-150 5-150 inH2O DR91505 3,470.00 DR915025 3,880.00 DR915015 4,332.00T9000-200 5-200 inH2O DR9205 3,490.00 DR92025 3,900.00 DR92015 4,358.00T9000-250 5-250 inH2O DR92505 3,549.00 DR925025 3,959.00 DR925015 4,395.00T9000-300 5-300 inH2O DR9305 3,724.00 DR93025 4,153.00 DR93015 4,610.00T9000-350 5-350 inH2O DR93505 3,900.00 DR935025 4,352.00 DR935015 4,825.00T9000-400 5-400 inH2O DR9405 4,074.00 DR94025 4,485.00 DR94015 4,920.00T9000-450 5-450 inH2O DR94505 4,237.00 DR945025 4,662.00 DR945015 5,115.00T9000-500 5-500 inH2O DR9505 4,310.00 DR95025 4,730.00 DR95015 5,182.00T9000-550 5-550 inH2O DR95505 4,384.00 DR955025 4,799.00 DR955015 5,245.00T9000-600 5-600 inH2O DR9605 4,436.00 DR96025 4,867.00 DR96015 5,315.00T9000-650 5-650 inH2O DR96505 4,530.00 DR965025 4,940.00 DR965025 5,382.00T9000-700 5-700 inH2O DR95705 4,599.00 DR957025 5,010.00 DR957015 5,445.00T9000-750 5-700 inH2O DR95750 4,668.00 DR957501 5,077.00 DR957502 5,515.00T9000-800 5-700 inH2O DR95800 4,735.00 DR958001 5,145.00 DR957800 5,580.00T9000-850 5-700 inH2O DR95850 4,805.00 DR958501 5,215.00 DR9578502 5,649.00Low Pressure Option DR9100 714.00 DR9100 746.00 DR9100 805.00

The floating ball deadweight tester is a highlyaccurate primary pressure standard ideally suitedfor portable calibrations. Combining unique de-sign features and ease of maintenance, these in-struments are the solution for many applicationsincluding gas measurement.

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Dual Column Deadweight Testers SPECIFICATIONSAccuracy Standard-± 0.1% of indicated pressure traceable to NIST.

Calibration to ± 0.025% is available with data furnished certified traceable to NIST. Calibration data is determined by cross floating against a laboratory standard traceable to NIST.

Test Fluid Type T Distilled water

Operating Pressure Type T 15,000 psi max

Wetted Parts Type T: 300 series SS and MonelType R: Aluminum, 300 series SS, carbon steel, brass and Monel

O-Rings Standard Buna N Optional Viton®, EPT

Test Connections Union type: 1⁄4" NPT, 1⁄2" NPT, 7⁄16" 20UNF (male and female)

Weight Type T & R-Hard, non-magnetic cast alloy, NIST certified .1%; conforming to material requirements of NIST Class Q

Pressure ComparatorsThe comparator is a pressure calibrating system us-

ing a source of controllable pressure and a “test” gaugeof known accuracy. “Test” gauges are variously knownas “transfer standard” or “inspection” gauges. The pressure source is connected to a manifold which directspressure equally to the “test” gauge and the instrumentsystem to be calibrated. The reading on the “test” gaugeis then compared to the indication given by the instrument system.

Catalog No. Model Range PriceAM900801 Type T-3 0 to 160, 600, 5000, 10,000 psi $3,592.00AM900802 Type T-3 oil 0 to 160, 600, 5000, 10,000 psi 3,592.00AM900803 Type T-3A 0 to 30, 600, 3000, 5000 psi 3,487.00AM900804 Type T-3A oil 0 to 30, 600, 3000, 5000 psi 3,487.00NISTDW7 — NIST Traceable Certificate with Data 1,250.00

SPECIFICATIONSAccuracy ± 0.25% of gauge span

(10,000 psi gauges, ± 0.5% of gauge span)Test Fluid Type T: Distilled Water and/or oilOperating Pressure 10,000 psi max.Wetted Parts Type T-300 series SS; O-Rings Buna N; Optional-Viton®, WPTTest Connections Union type 1⁄4" NPT, 1⁄2" NPT, 7⁄16"-20 UNF

(male or female)Gauge Connections Type T: 9⁄16"-18 UNF-3A

All gauges supplied with union type connectionsOperating DImensions 20 5⁄8" long x 11" wide x 16" highApproximate Weight 55 lbs.

Catalog No. Model Range Increments PriceAM900901 DM-T-50 10 to 500 psi 5 psig $3,487.00

Dual Range 100 to 5000 psi 50 psigAM900902 DM-T-100 10 to 1000 psi 5 psig 5,267.00

Dual Range 1000 to 10,000 psi 50 psigAM900903 DM-T-150 10 to 1500 psi 5 psig 5,803.00

Dual Range 100 to 15,000 psi 50 psigNISTDW4 NIST Traceable Certificate with Data 545.00

• Hand operated hydraulic pump, with manual dual volume control valve,delivers high volume to rapidly build pressure and low volume for easeof pumping and a gradual approach to the point of calibration. Testmanifold with pressure vernier for fine adjustment of pump pressure.

• Supplied with four U.S. Gauge 4 1⁄2" Test Gauges• NIST Certification included

• Separate columns provided forhigh and low pressure measuringpiston/cylinder assemblies. Rangechanges are done by using a builtin cross over valve

• Kits available to convert standardT &R testers to dual column Type DM

• Dual volume pump delivers higherpressures with minimal effort

• Suspended weights reduce sidethrust on measuring piston/cylinder assemblies

• Piston and cylinder are completelyenclosed in unique column design

NIST it

NIST it




H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

758

• Ranges up to 10,000 psi• Accuracy 0.025% FS• Built-in pressure generation with priming pump• Data storage with RS232 interface• Self contained in carrying case with detachable lid

SPECIFICATIONSAccuracy 0.025% FS(non-linearity, hysteresis, repeatability)

Temperature Effects ± 0.002% reading/°F averaged over 15°F to 105°F w.r.t. 68°F

Electrical Inputs

Input Range Accuracy Resolution Remarks

Voltage* ± 50V DC ± 0.05% Rdg. 100µV max Autoranging,± 0.004% F.S. >10 MΩ

Current* ± 55mA ± 0.05% Rdg. 0.001mA 10Ω, ± 0.004%F.S. 50V max.

Temperature 15° to 105°F ± 2°F 0.1°F Local ambient

Switch Open/Closed 5mA whetting

Electrical Outputs

Output Range Accuracy Resolution Remarks

Voltage 10V DC ± 0.1% Max. load 10mA

24V DC ± 5% Max. load 26mA

Current* 0 to 24 mA ± 0.05% Rdg. 0.001mA± 0.01%F.S.

* Temperature coefficient ± 0.0075% reading / °C w.r.t. 20 °C

Display

Panel 2.36 x 2.36 inch graphic LCD with backlight

Readout ± 99999 capability, 2 readings per second

Temperature

Operating 15° to 120°F

Calibrated 15° to 105°F

Humidity 0-90% non-condensing

Conformity EN61010, EN50081-1, EN50082-1, CE marked

Dimensions Including lid: 18.5 x 12.6 x 7.9 inches (LxDxH)

Weight 26.4 lbs

Digital Pressure Calibrators

Catalog No. Model Description PriceDR55020 CA020 Digital Pressure Calibrator, -14.7 to 300 psi $4,832.00DR55140 CA140 Digital Pressure Calibrator, 0 tp 2000 psi 4,995.00DR55011 — Built-in hand pump for CA020 & CA140 729.00

DR54020 C020/P Digital Pressure Calibrator, 0 to 300 psi 5,720.00DR54160 C160/P Digital Pressure Calibrator, 0 to 2500 psi 5,720.00DR54350 C350/P Digital Pressure Calibrator, 0 to 5000 psi 5,720.00DR54700 C700/P Digital Pressure Calibrator, 0 to 10,000 psi 5,720.00DR541000 C1000/P Digital Pressure Calibrator, 0 to 15000 psi 6,025.00C Series supplied with built-in hand pump for large volume operations as standard

DR53020 CW020/P Digital Pressure Calibrator, 0 to 300 psi 5,995.00DR53160 CW160/P Digital Pressure Calibrator, 0 to 2500 psi 5,995.00DR53350 CW350/P Digital Pressure Calibrator, 0 to 5000 psi 5,995.00DR53700 CW700/P Digital Pressure Calibrator, 0 to 10,000 psi 5,995.00DR531000 CW1000/P Digital Pressure Calibrator, 0 to 15000 psi 6,295.00DR55012 — Dual pressure option for CW Series 1,040.00

hydraulic modelsCW Series supplied with built-in hand pump for large volume operations as standard


NIST it ™

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Positive/Negative Pressure Transmitter/Indicator

SPECIFICATIONSAccuracy 0.25% B.F.S.L.Temperature Sensitivity .011% / °FBody 304 SSProcess Connections 1⁄2" NPT standard; (1⁄4" NPT optional)Output Signal 4-20 mA; (0-5V or 0-10V optional)Input Power 10-30 VDCElectrical Connection 4 pin solderless connection (4 wire cable)

Catalog No. Model Description PriceWK33398 8642850 0 to 30" Hg vacuum $415.00WK33397 8642885 0 to 10psi 295.00WK33396 8643652 0 to 100psi 295.00WK33395 8341740 0 to 500 psi 335.00WK33394 8610007 0 to 1000 psi 335.00WK33393 8342275 0 to 3000 psi 335.00WK33392 8340638 0 to 5000 psi 335.00PD885100 PD690-3-N Digital Indicator 117VAC 239.00PD885105 PD690-3-18 Digital Indicator 117VAC w/4 relay output & 4-20mA 478.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00For additional digital indicators, Please see page 143

NIST it

Digital Indicator Features• Easy single button scaling • Steady, accurate display to

± 199,990• 41⁄2 Digits + extra zero• UL Listed

• 4 Alarm points with LED statusindication

• NEMA 4 front panel• Isolated 24V transmitter power

supply

Optional Digital Indicator

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

760

Pressure Transmitter/Transducer NIST it

Compact Design and Rugged SensorAvailable in ranges from 15 PSI to 15,000 PSI. The transmitter

version provides a 4-20 mA 2-wire output signal. The transducerversion supplies a 0-10 VDC 3-wire output signal. Both signals arefully conditioned and provide an output that is both linear and pro-portional to the applied pressure.

The compact design provides a rugged sensor suitable for manygeneral purpose pressure measurement applications in hydraulics& pneumatics, press control, compressor control, pump protectionand numerous other monitoring and control options.

SPECIFICATIONSInput (supply) 10-30 VDC

(14-30 VDC for 0-10V output signal)Output & load limitations4-20 mA 2-wire R(max) = (VS -10V) / 0.02 A0-10V 3-wire R(min) = 5 k OhmAccuracyLinearity (B.F.S.L.) ≤0.5% of spanHysteresis ≤0.1% of spanRepeatability ≤0.1% of span1 yr. stability ≤0.3% of spanResponse time ≤5 ms(10-90% full scale)Temperature compensated + 32 °F to 175 °FMedia -25 °F to 212 °FAmbient -25 °F to 175 °FStorage -40 ° F to 212 °FTemperature error (reference temperature 70 °F)On zero (% of span / °F) ≤0.022On span (% of span / °F) ≤0.016Process connection 1⁄4" NPT maleElectrical connection DIN 43650 solderless screw terminal

(IP 65 / NEMA 5)MaterialWetted parts 316 stainless steelBody material 304 stainless steelElectrical protection Protected against reverse polarity,

short circuit output and suppressor diode for high-voltage protectionVibration resistance 15 g between 15...2000 HzShock resistance 600 g

Pressure Maximum Burst 4-20 mA 0-10VRange Pressure Pressure 2-Wire 3-Wire0-15 psi 75 psi 75 psi WK40001 WK400100-50 psi 245 psi 245 psi WK40002 WK400110-100 psi 500 psi 500 psi WK40003 WK400120-500 psi 1160 psi 2900 psi WK40004 WK400130-1000 psi 1740 psi 4350 psi WK40005 WK400140-2000 psi 2900 psi 7250 psi WK40006 WK400150-5000 psi 11,600 psi 18,850 psi WK40007 WK400160-10,000 psi 17,400 psi 26,100 psi WK40008 WK400170-15,000 psi 21,750 psi 43,500 psi WK40009 WK40018Price $165.00 $165.00AccessoriesML428271 Process Power Pack 24VDC-175mA $130.90NISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00

Loop-Powered Attachable Digital Indicator

Catalog No. Model No. Description PriceWK90715507 907-15-507 Attachable Loop Powered Digital Indicator $229.00

For use with Wika S-10, S-10-3A or ECO-Trans with full size DIN plug

Does not include 4-20 mA Transmitter shown (see page for 643 transmitter)NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

• Attachable liquid crystal displayfor local indication

• 4-20 mA current loop-poweredwith 3 volt drop

• Installs between transmitter and DIN 43 650, + full sized “L” shaped 4-pin connector

• Programmable Range: 4-20 mA can be assigned anydisplay value within the displayrange

• User scalable to display rangefrom -1999 to + 9999

• Accuracy: ≤ 0.2% of span

SPECIFICATIONSDisplay Type 0.4" high LCD Programmable display range:

-1999 to + 9999Power Loop Powered - no additional power supply

requiredVoltage drop 3 VDCMaximum current 60 mAratingEnvironmentalOperating + 32 to + 122°F (0 to 50°C)TemperatureStorage -22 to + 176°F (-30 to + 80°C)TemperatureTemperature effects 0.1% of span per 18°F (10°C)Humidity <90%, non-condensingDimensions (inches) 1.9 x 1.9 x 1.4 deep

NIST it



H

High Accuracy Pressure Transmitters NIST it

Range Acc. FS Cat . No. Price Acc. FS Cat . No. Price30” Hg. Vac. 1% ASK17420 $276.00 —15 PSIG 1% ASK174215 261.00 —30 PSIG 1% ASK174230 261.00 —60 PSIG 1% ASK174260 251.00 —100 PSIG 1% ASK1742100 251.00 0.5% ASK1542100 $316.00150 PSIG 1% ASK1742150 251.00 0.5% ASK1542150 316.00200 PSIG 1% ASK1742200 251.00 0.5% ASK1542200 316.00300 PSIG 1% ASK1742300 251.00 0.5% ASK1542300 316.001000 PSIG 1% ASK171000 251.00 0.5% ASK151000 316.002000 PSIG 1% ASK172000 251.00 0.5% ASK152000 316.003000 PSIG 1% ASK173000 251.00 0.5% ASK153000 316.005000 PSIG 1% ASK175000 251.00 0.5% ASK155000 316.0030” Hg./15 PSIG 1% ASK174215V 276.00 —30” Hg./30 PSIG 1% ASK174230V 276.00 —30” Hg./60 PSIG 1% ASK174260V 276.00 —NISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00Standard output 4-20mA, connection 1/4” NPTM, 36” cable shielded PVC 24 AWG.* Connection 9/16-Aminco (Female)

SPECIFICATIONSAccuracy Class (F.S.) 0.5% 1.0%Non-Lin. (Term. Pt.)* ± 0.4% ± 0.7%

(B.F.S.L.)* ± 0.25% ± 0.4%Hysteresis ± 0.15± ± 0.2%Non-Repeatability ± 0.05% ± .07%*Including hysteresisOverpressure (F.S.) 0/15- 0/3000- 0/7500-

0/2000 0/5000 20,000Proof 200% 150% 120%Burst 800% 300% 150%Response Time Less than 5 msTemperatureOperating -20/+ 180°FCompensated -20/+ 160°FThermal Coefficients (68°F ref.) Standard

0.5% 1%Zero ± 0.028% F.S./°F ± 0.04% F.S./°FSpan ± 0.028 ± 0.04MaterialsCase 300 series stainless steelCable No. 24 AWG, 36" PVC, shielded, vented, UL approvedDiaphragm 17-4 PH stainless steelPower 10-36 VDC Unregulated,Requirements Reverse polarity protectedSupply Current Less than 3. mA for voltage outputOutput Impedance 100Ω

The K1 transmitter offersthe benefits of polysiliconthin film performance at af-fordable prices. Using chemi-cal vapor deposition methodspolysilicon strain gages aremolecularly bonded to a met-al diaphragm. This sensor,combined with the latestsurface mount electronicspromote superior perfor-mance in a durable package.The K1 is designed for use inmany demanding OEM ap-plications including air com-pressors and refrigerationcontrols, hydraulic controlsand other industrial controlapplications.

• 0.5% Full scale accuracy• Voltage or current output• Superior long term stability and

reliability• 1-year warranty• NIST certification included with

0.5% unit, 1.0% optional

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

762

Pressure Transmitters

Catalog No. Model Description PriceVI247 247G Pressure Transmitters, choose range below $180.00VI2471 247A Absolute Pressure Transmitter (≤200 PSI) 220.00VI2472 247V Vacuum Pressure Transmitter (≤15 PSI) choose range below 195.00VI347 347G Pressure Transmitter, choose from range below 180.00VI3471 347A Absolute Pressure Transmitter (≤200 PSI) choose range below 220.00VI3472 347V Vacuum Pressure Transmitter (≤15 PSI) chooser from range below 190.00Standard Pressure Ranges, please choose code that matches your specific rangeCode Range Code Range Code Range Code Range AA 0-5 AM 0-100 AW 0-750 BE 0-4000AB 0-10 AP 0-200 AY 0-1000 BF 0-5000AC 0-15 AR 0-300 AZ 0-1500 BH 0-7500AF 0-30 AT 0-400 BA 0-2000 BM 0-10KAH 0-50 AU 0-500 BC 0-3000 BP 0-15KAK 0-75AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTQ133 — 2 Year NIST Traceable Certificate with Data 195.00Other options and accessories available, please inquire.

Viatran's Models 247 and 347 are designed forapplications where very rugged yet inexpensivepressure transmitters are required.

This enables Viatran to provide the advantagesof bonded foil sensing technology at prices typicalof less reliable semiconductor sensors.

The "47" Series is available with pressureranges from 0-10 to 0-20K PSI.

The "47" Series has zero adjustment controlthat also makes setup fast and easy.

When your application requires a large quanti-ty of rugged pressure transmitters, Viatran's "47"Series offers the same high quality standards thatyou build into your equipment.

SPECIFICATIONSFull Scale Pressure Range (FSPR) 0-10, 0-15, 30, 50, 75, 100, 200, PSIG, PSIA, 0-300, 400

500, 750, 1K, 1500, 2K , 3K, 4K, 5K, 7500, 10K, 15K, 20K, PSIGNon-Linearity (Best Fit Straight Line) ≤ ± 0.5% FSOHysteresis & Repeatability < .25% FSOFull Scale Output (FSO) Model 247 5 VDC ± 2% at 70°F

Model 347 16 mA ± 2% at 70°FResolution InfiniteLong Term Stability ≤ ± 0.5% FSO pper 6 monthsCompensated Temperature Range 70°F to 170°FMaximum Operating Temperature Range 200°FMinimum Operating Temperature Range -20°FElectricalSupply Voltage 10 to 40 VDCOutput Signal Model 247 0 to 5 VDC

Model 347 4 to 20 mAMechanicalPressure Connectors 1/4" NPT FemaleProof Pressure 1.5 times FSPR or 25K PSI, whichever is lessBurst Pressure 5 times FSPR or 30K PSI, whichever is less

• Low price• Adjustable zero• Resistance to pressure

spikes• Cost effective DIN connector• Welded stainless steel

constructionApplications• Hydraulic systems• Injection molding • Die casting• Off road vehicles• Compressors and pumps• High volume usage

NIST it



H

Pressure Transmitter

Catalog No. Model Description PriceVI970 970A- Absolute pressure transmitter (up to 15K). Please choose range below. $955.00VI971 970A- Absolute pressure transmitter (20K and above). Please choose range below. 1,355.00VI972 970S- Sealed gauge pressure transmitter (up to 15K). Please choose range below. 915.00VI973 970S- Sealed gauge pressure transmitter (20K and above). Please choose range below. 1,315.00AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00Other options and accessories available, please inquire.

Viatran's Model 970, designed specifically for the oilproduction industry, features a HART communicationsprotocol that enables digital communication with thetransmitter. This allows for self diagnostics, the set-ting, storage, and recall of calibration data, as well asthe efficiency of a multidrop network for multiple trans-mitters

The HART protocol allows a simultaneous analogand digital signal transmission.

The "70" Series also features bonded foil strain gaugesensors. The inherent overpressure protection in thistechnology helps to eliminate damage to the sensorswhen they are exposed to hydraulic spikes.

SPECIFICATIONSFull Scale Pressure Range (FSPR) 0-100, 150, 300, 500, 750, 1K, 1500, 2K,

3K, 5K, 7500, 10K, 15K, 20K, 30K, 40K, 50K, 60K, 75K, 100K PSIS, PSIA

Linearity (BFSL)0-100 PSI ± 0.5% FSO150-10K PSI ± 0.2% FSO15K - 20K PSI ± 0.25% FSOHysteresis ≤ ± 0.1% FSORepeatability ± 0.1% FSOFull Scale Output 16 mAResolutionSensor (Analog to Digital Converter) 18 bitsOutput (Digital to Analog Converter) 12 bitsDrift ≤ ± 0.25% FSO per 6 monthsResponse Time Analog output response to a step change in

pressure will be from 0.07 sec. minimum to a36 sec. maximum for one time constant and is adjustable through software.

Thermal Zero Shift ≤ ± 1.0% FSO per 100°FThermal Sensitivity Shift ≤ ± 1.0% FSI per 100°FOperating Temperature Range -40°F to + 190°FNon-Operating Temperature Range -65° F to + 250° FSupply Voltage 7 to 30 VDCOutput Signal Two wire 4-20mA. Digital process signal

superimposed on 4-20mA signal, available toany host computer system conforming toHART protocol.

Load Impedance 230 Ω to 1,400 ΩPressure Connection0-100 thru 0-15K 1/4" NPT(F)0-20K thru 0-50K 9/16" - 18 gland thread, pressure relieved.

1/4" OD high pressure tube, 60° come. Conforms to autoclave type F250-C

0-60K thru 0-100K 5/8" - 18 gland thread, pressure relieved. 5/16" OD high pressure tube, 60° cone. Conforms to autoclave type F312-C150.

• Simultaneous digital/analog communications• 10:1 rangeability• Small size and weightApplications• Offshore oil rigs• Oil production platforms• Natural gas pipelines• Rig safety systems

Standard Pressure Ranges in PSI - when ordering, please choose code that matches your specific range.Code Range Code Range Code Range Code RangeAH 0-50 AW 0-750 BF 0-5000 BS 0-30KAM 0-100 AY 0-1000 BH 0-7500 BU 0-40KAN 0-150 AZ 0-1500 BM 0-10K BW 0-50KAP 0-200 BA 0-2000 BP 0-15K BZ 0-60KAR 0-300 BC 0-3000 BQ 0-20K EC 0-75KAU 0-500 BR 0-25K EG 0-100K

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

764

Pressure Transmitter - Gauge & Absolute

Catalog No. Model Description PriceVI571 571A- Absolute pressure transmitter (up to 15K). Please choose range below. $910.00VI572 572A- Absolute pressure transmitter (20K and above). Please choose range below. 1,310.00VI573 571S- Sealed gauge pressure transmitter (Up to 15K). Please choose range below 880.00VI574 571S- Sealed gauge pressure transmitter (20K and above). Please choose range below 1,280.00AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

Viatran's small andrugged Model 571 pressuretransmitter is designed foraccurate and stable mea-surement of medium tohigh pressures. A sealedgauge (PSIS) or absolute(PSIA) pressure referenceis available.

Compact and complete-ly sealed, the Model 571 isdesigned to withstandharsh atmospheres andsubmersion to 100 feet. Allwelded construction andthe use of 316 stainless

steel makes the 571 airtight, watertight, and idealfor corrosive environments. The "O" Ring free de-sign simplifies the transmitter and ensures relia-bility.

Model 571 qualifies for CSA and FM explosionproof type rating, as well as the CENELEC(NEMKO) flameproof approval. The 571 has alsobeen approved by FM as intrinsically safe (entity).

External zero, span, and calibration controlsare hermetically sealed, yet easily adjusted bymeans of Viatran's unique magnetically-coupleddrive system. The signal conditioner in the 571 al-lows for 5:1 ranging of the transmitter's standardpressure range.

A special feature of this transmitter is a cali-bration circuit that permits setup and ranging inthe field - without the need for a calibrated pres-sure source.

SPECIFICATIONSFull Scale Pressure Range (FSPR) 0-100,150,300, 500, 1000, 2000, 3000, 5000, 10K,

15K, 20K, 25K, 30K, 40K, 50K, 60K, 75K, 100KPSIA/PSIS

Non-linearity (Best fit straight line) Typical @ 0.20% FSO (see graph)Hysteresis & Repeatability ≤ ± 0.10% FSOFull Scale Output 16mA at 70°FResolution InfiniteLong Term Stability ≤ ± 0.25% FSO per 6 monthsResponse TimeMechanical and Electrical Combined ≤ 20mSec to reach 90% of FSOTemperature Effect on Zero ≤ ± 0.5% FSO per 100°FTemperature Effect on Span ≤ ± 0.5% FSI per 100°FTemperature Effect on Zero & Span ≤ ± 4.0% FSO per 100°combined at 5:1 Range DownCompensated Temperature Range 0°F to + 180°FMax./Min. Operating Temperature + 190°F / -10°FNon-Operating Temperature Range -65°F to + 250°FElectricalSupply Voltage 10-40 VDCOutput Signal 4-20mA at 70°FLoad Impedance 1500 Ohms maximum at 40 VDCZero Adjustment Elevation -100% of FSOSpan Adjustment Rangeable down 5:1 from standard rangeCalibration Signal Accuracy ± 1.0% FSO. The exact signal to pressure correlation is provided with each unitMechanicalPressure Connections0-100 thru 0-15K PSI 1/4" NPT female0-20K thru 0-50K PSI 9/16" - 18 gland thread, pressure relieved, 1/4" OD

high pressure tube, 60° cone. Conforms to autoclavetype F-250-C. F-312-C150 fitting and also available at these ranges

0-60K thru 0-100K PSI 5/8" = 18 gland thread, pressure relieved. 5/16" OD high pressure tube, 60° cone. Conforms to autoclavetype F-312-C150

Proof Pressure0-100 thru 0-15K PSI 1.5 times FSPR or 20K PSI - whichever is less0-20K thru 0-100K PSI 1.2 times FSPRBurst Pressure0-100 thru 0-3K PSI ≥ 5 times FSPRUp to 0-5K PSI ≥ 4 times FSPRUp to 0-10K PSI ≥ 2.7 times FSPRUp to 0-15K PSI ≥ 2.3 times FSPRUp to 0-100K PSI ≥ 1.5 times FSPR or 125K PSI - whichever is lessShock Limitation 100 G'sWeight 24 oz.CertificationsEnclosure Classification NEMA 4XIntrinsically Safe FM approved for use in Class I, II, & III, Div. 1, Groups

A thru G indoor and outdoor. NEMKO/CENELEC (approval pending) EEx la IIC T6

Explosion Proof FM approved as suitable for use in Class I, II, III, Div.1, Groups A thru G, Hazardous locations. CSAapproved for use in Class I, Div. 1, Groups A, B, C &D, Class II, Div. 1, Groups D, F & G, and Class III, Div.1 for Hazardous locations. NEMKO/CENELECapproved flameproof EEx d IIC T6

• Hermetically sealed externalcontrols

• Built-in calibration signal• All welded, watertight con-

struction• Submersible• FM, CSA & CENELEC

Certification (optional)Applications• Offshore oil rigs• Shipboard/Marine• Pulp and paper• Chemical processing• Water treatment

Standard Pressure Ranges in PSI - when ordering, please choose code that matches your specific range.Code Range Code Range Code Range Code RangeAH 0-50 AW 0-750 BF 0-5000 BS 0-30KAM 0-100 AY 0-1000 BH 0-7500 BU 0-40KAN 0-150 AZ 0-1500 BM 0-10K BW 0-50KAP 0-200 BA 0-2000 BP 0-15K BZ 0-60KAR 0-300 BC 0-3000 BQ 0-20K EC 0-75KAU 0-500 BR 0-25K EG 0-100K

NIST it



H

LVDT Pressure Transducers

Catalog No. Model Description PriceAM7470 P207PXD0030A Pressure Transducer, 0-30 PSIG, 1-5VDC Voltage Output $190.00AM7471 P207PXD0100 Pressure Transducer, 0-100 PSIG, 1-5VDC Voltage Output 190.00AM7472 P207PXD0300 Pressure Transducer, 0-300 PSIG, 1-5VDC Voltage Output 190.00AM7473 P207PXD1000 Pressure Transducer, 0-1000 PSIG, 1-5VDC Voltage Output 190.00AM7474 P207PXD3000 Pressure Transducer, 0-3000 PSIG, 1-5VDC Voltage Output 190.00AM7475 P207PXT0030A Pressure Transducer, 0-30 PSIG, 4-20mA Current Output (2 Wire Transmitter) 195.00AM7476 P207PXT0100 Pressure Transducer, 0-100 PSIG, 4-20mA Current Output (2 Wire Transmitter) 195.00AM7477 P207PXT0300 Pressure Transducer, 0-300 PSIG, 4-20mA Current Output (2 Wire Transmitter) 195.00AM7478 P207PXT1000 Pressure Transducer, 0-1000 PSIG, 4-20mA Current Output (2 Wire Transmitter) 195.00AM7479 P207PXT3000 Pressure Transducerr, 0-3000 PSIG, 4-20mA Current Output (2 Wire Transmitter) 195.00PD885100 PD690-3-N Digital Indicator 117VAC 229.00PD885105 PD690-3-18 Digital Indicator 117VAC w/4 relay output & 4-20mA 478.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

SPECIFICATIONSPressure Range 0 to 30 through 6000 psi, compound ranges available, consult factoryOver Pressure 110% full scaleOutput Voltage and Current 1 to 5 VDC and 4 to 20 mA standard. Other output voltages ranges optionalSupply Voltage 9 to 28 VDC for voltage output units 15 to 40 VDC for current output unitsSupply Current 15 mA maximum (VDC output only)Ambient Operating Temperature Range 1 to 5 vDC Output Standard: -40° to 85°C 4 to 20 mA Output Standard: -20° to 70°CLoad Impedance 2000 ohms minimum (voltage output only)Bourdon Tube Standard Beryllium copper brazed to brass connectionBourdon Tube Optional 316 stainless steel welded to 316 stainless steel connectionPressure Connection 1/8-27 ANPT standardHousing Molded Ultem™ 2300*Electrical Connection 7-1/2 inch long, 18 AWG leadsAccuracy ± 2% of span maximum at 25°C (includes linearity, hysteresis, and repeatability)Temperature effects 0.033%/°C typical on zero and span (when operated within ambient operating range)





supply

• Compact design, shock/vibration resistant• Operating pressure ranges up to 6000 psi• Reliable bourdon/LVDT technology• Temperature ranges up to 85°C• Corrosion resistant wetted parts, weather resistant design• Infinite resolution output• Stable/repeatable output• Microprocessor compatible


NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

766

Stainless Steel Pressure Transducers

Catalog No. Model Description PriceAM48610 IPTS0030A Pressure Transducer, 0-30 PSI, 10 VDC/0-100 mV $200.00AM48611 IPTS0100A Pressure Transducer, 0-100 PSI, 10 VDC/0-100 mV 200.00AM48612 IPTS0500A Pressure Transducer, 0-500 PSI, 10 VDC/0-100 mV 200.00AM48613 IPTS0030B Pressure Transducer, 0-30 PSI, 12-25 VDC/4-20 mA 250.00AM48614 IPTS0100B Pressure Transducer, 0-100 PSI, 12-25 VDC/4-20 mA 250.00AM48615 IPTS0500B Pressure Transducer, 0-500 PSI, 12-25 VDC/4-20 mA 250.00PD885100 PD690-3-N Digital Indicator 117VAC 229.00PD885105 PD690-3-18 Digital Indicator 117VAC w/4 relay output & 4-20mA 478.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

• 0.3% accuracy• Excellent stability• Solid state/industrial grade• Temperature compensated• Stainless steel wetted parts for maximum media

compatibility• Rugged Ultem housing provides outstanding

corrosion resistance• Seven standard pressure ranges up to 500 PSIG• mV, Voltage or 4-20mA output available• Vacuum and compound pressure ranges available

SPECIFICATIONSPressure Range 0/30 to 0/500 PSIGMax. Overpressure 2 times full scale or 750 PSIG, whichever is lessBurst Pressure (at 25°C) 5 times full scaleAccuracy ± 0.3% span from best fit straight line including non-linearity repeatability & hysteresisOperating Temperature Range -40° to 105°CCompensated Temperature Range -5° to 55°CThermal Effect on Zero (Null) ± 0.5% span (typical) over compensated temperature range, ± 2% maxThermal Effect on Span ± 0.5% span (typical) over compensated temperature range, ± 2% maxResponse Time <20 MillisecondsStability ± 0.25% Span/YearShock 100 gVibration 10g 100-2000 HzWeight 50 gramsElectrical Terminations #20 AWG Shielded Wire/18” longMedia Compatibility 316 Stainless Steel Wetted PartsHumidity Passes MIL-STD-202F Method 103B, Condition A





supply

NIST it


Isolated, Industrial quality

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Stainless Steel Pressure Transducers

Catalog No. Model Description PriceAM48410 SPTC035 Pressure Transducer, Vacuum - 35 PSIG $230.00AM48411 SPTC025 Pressure Transducer, 0-25 PSIG 230.00AM48412 SPT0100 Pressure Transducer, 0-100 PSIG 230.00AM48413 SPT0500 Pressure Transducer, 0-500 PSIG 230.00AM48414 SPT1000 Pressure Transducer, 0-1000 PSIG 250.00AM48415 SPT5000 Pressure Transducer, 0-5000 PSIG 250.00PD885100 PD690-3-N Digital Indicator 117VAC 229.00PD885105 PD690-3-18 Digital Indicator 117VAC w/4 relay output & 4-20mA 478.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

• 316 Stainless steel wetted parts for maximum media compatibility• 5X burst pressure rating• 0.25% accuracy• Excellent stability• Solid state/industrial grade• Temperature compensated• Rugged Ultem housing provides outstanding corrosion resistance• 10 standard pressure ranges up to 5000 psig• Amplified output (1-6 VDC standard)• Unregulated supply requirement (8-15 VDC)• Vacuum and compound pressure ranges available• Automotive style Packard connector

SPECIFICATIONSPressure Range Ref. Ordering Info.Maximum Overpressure 2 times full scaleBurst Pressure (at 25°C) 5 times full scale up to 1000 PSI 3 times full scale greater than 1000 PSIExcitation 8 to 15 VDCNull Offset (at 25°C) 1.0 VDC ± 2% spanSpan (at 25°C) 5.0 VDC ± 1% spanAccuracy ± 0.25% span from best fit straight line including non-linearity, repeatability & hysteresisOperating Temperature Range -40° to 105°CCompensated Temperature Range -5° to 55°CThermal effect on zero (null) ± 0.5% span (typical) over compensated temperature range, 2% maxThermal effect on span ± 0.5% span (typical) over compensated temperature range, 2% maxResponse Time <20 Milliseconds Stability ± 0.25% Span/YearShock 50 g Weight 50 gramsElectrical Terminations Packard Connector #12162189 with 18” leadsMedia Compatibility 316 Stainless Steel Wetted PartsHumidity Passes MIL-STD-202F Method 103B, Condition AProtection Class IP-64Output Impedance >50K ohms





supply

Isolated Amplified Output

NIST it



H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

768

SPECIFICATIONS

Fixed Range Pressure Transmitters

Catalog No. Model Description PriceAM23740 8310015 Fixed Range Pressure Transmitter, 0 to 15 PSIG $300.00AM23741 8310100 Fixed Range Pressure Transmitter, 0 to 100 PSIG 300.00AM23742 8311000 Fixed Range Pressure Transmitter, 0 to 1000 PSIG 300.00AM23743 8315000 Fixed Range Pressure Transmitter, 0 to 5000 PSIG 300.00Note: Factory Mutual (FM) Explosion Proof Approval is StandardPD885100 PD690-3-N Digital Indicator 117VAC 229.00PD885105 PD690-3-18 Digital Indicator 117VAC w/4 relay output & 4-20mA 478.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

• A miniature, low-priced fixed range transmitter, just 0.83 lbs. (374 grams)

• All welded 316 stainless steel construction and wetted parts (no aluminum)

• Ranges form vacuum to 5000 psi (0 to 1 to 0 to 345 bar)• ± 0.30% accuracy• FM and CSA Explosion Proof Approvals• 4 to 20 mA output at 12 to 30 VDC• 3/4-Inch NPT Female conduit connection cable• 1/2-Inch NPT Female pressure port connection• Straight in-line construction for a slim profile• 24 Inch cable standard• Optional 1-5 VDC output at 8-14 VDC

Ranges 0 to 15 psi (0 to 1.0 bar)0 to 30 psi (0 to 2.1 bar)0 to 100 psi (0 to 6.9 bar)0 to 300 psi (0 to 20.7 bar)0 to 1000 psi (0 to 69.0 bar)0 to 3000 psi (0 to 206.9 bar)0 to 5000 psi (0 to 344.8 bar)

Output 4 to 20 mADC, limited to 30 mADCOffset 4.0 mA ± 2.0% spanSpan 16.0 mA ± 1.0% spanPower supply 12 to 30 VDC with reverse polarity protectionLoop resistance 900 ohms maximum at 30 voltsTemperature LimitsElectronics (Ambient) -40°F to 140°F (-40°C to 60°C)Process Interface -40°F to 212°F (-40°C to 100°C)Storage -40°F to 212°F (-40°C to 100°C)

Overrange 300%Humidity Limits 0 to 100% RHAccuracy ± 0.30% of calibrated span including linearity,

hysteresis and repeatability at 25°C and 12 VDC excitation

Stability ± 0.50% for six monthsTemperature Effect (includes zero and span) between -20°F and

140°F (-29°C and 60°C): ± 2.0% per 50°F (28°C)Vibration Effect ± 0.10% for 3 g to 200 HzOverrange Effect ± 0.15% full scale per 200% of maximum rangeProcess Wetted Parts 316L Stainless SteelNon Wetted Parts 316 Stainless SteelFill Fluid DC 200 Silicone (Standard)Process Connection 1/2 Inch NPT FemaleElectrical Connection 3/4 Inch NPT FemaleWeight .83 lb (374 grams)Cable Lengths 24 inches (61 cm), 22 AWG





supply

For use with Liquid, Gas or Vapor


NIST it



H

Miniature Pressure Transmitters

Catalog No. Model Description PriceAM947720 88C003 Miniature Electronic Pressure Transmitter, 0/6 to 0/30 PSI $625.00AM947721 88C005 Miniature Electronic Pressure Transmitter, 0/60 to 0/300 PSI 625.00AM947722 88C006 Miniature Electronic Pressure Transmitter, 0/200 to 0/1000 PSI 655.00AM947723 88C008 Miniature Electronic Pressure Transmitter, 0/1000 to 0/5000 PSI 655.00PD885100 PD690-3-N Digital Indicator 117VAC 229.00PD885105 PD690-3-18 Digital Indicator 117VAC w/4 relay output & 4-20mA 478.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

• A miniature, low-priced, full-featured transmitter — just 1.67 lb.• All welded 316 stainless steel construction and wetted

parts (no aluminum)• Ranges from 0 to 3 to 0 to 5000 psig (0 to 0.2 to 0 to 350 bar)• ± 0.25% accuracy• Zero and span adjustability• Full 5:1 range turndown• Integral junction box• FM and CSA explosion-proof and intrinsically safe• 4 to 20 mA output at 12 to 40 VDC• 316SS Base and Hastelloy C Diaphragm, Silicone Oil Fill• 5-year warranty

SPECIFICATIONS

Functional SpecificationsService Liquid, gas or vaporRange Limits

0/. to 0/6 psi (0/0.2 to 0/0.4 bar) consult factory 0/6 to 0/15 psi (0/0.4 to 0/1 bar)0/15 to 0/30 psi (0/1 to 0/2 bar)0/20 to 0/100 psi (0/1.4 to 0/7 bar)0/60 to 0/300 psi (0/4 to 0/20 bar)0/200 to 0/1000 psi (0/14 to 0/70 bar)0/600 to 0/3000 psi (0/40 to 0/200 bar)0/1000 to 0/5000 psi (0/70 to 0/350 bar)

Output 4 to 20 mADC, limited to 30 mADCPower Supply 12 to 40 VDC with reverse polarity protectionLoop Resistance 1400 ohms maximum at 40 voltsTurndown 5:1Zero Adjust ± 10%Span Adjust ± 10%Temperature LimitsElectronics (Ambient) -40° to 140°F (-40° to 60°C)Process Interface -40° to 212°F (-40° to 100°C)Storage -40° to 212°F (-40° to 100°C)Overrange 300% upper range limitHumidity Limits 0 to 100% RH

Accuracy ± 0.25% of calibrated span including linearity,hyteresis and repeatability

Response Time Time constant of 20 millisecondsStability ± 0.5% of upper range limit for six monthsTemperature Effect (includes zero and span)Compensated -20° to 180°F (-29° and 82°C)Between 30° and 130°F ± 1% of URL per 50°F (28°C) (-1° and 54°C)Between -20° and 180°F ± 1.6% of URL per 50°F (28°C)(-29° and 82°C)Power Supply Effect ± 0.005 full scale per voltSurge Protection StandardVibration Effect ± 0.1% of upper range limit for 3 g to 200 HzPosition Effect 0.05%/90° tiltOverrange Effect ± 0.15% full scale per 200% of maximum rangeProcess Wetted Parts 316 stainless steelNonwetted Parts 316 stainless steelCast head CF-8M (316 cast stainless steel)O Ring Buna NFill Fluid DC 200 Silicone (standard)Process Connection 1/2 NPTFElectrical Connection 1/2 NPTFWeight 1.67 lbs.





supply

NIST it


Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

770

316 Stainless Digital Compensated Pressure Transducer

Catalog No. Model Description PriceAM316147 DCTC0030PT021 Pressure Transducer 1/4 NPT 4-20mA, -14.7-30psi $230.00AM316060 DCTG0006PT021 Pressure Transducer 1/4 NPT 4-20mA, 0-6psi 230.00AM316030 DCTG0030PT021 Pressure Transducer 1/4 NPT 4-20mA, 0-30psi 230.00AM316100 DCTG0100PT021 Pressure Transducer 1/4 NPT 4-20mA, 0-100psi 230.00AM316300 DCTG0300PT021 Pressure Transducer 1/4 NPT 4-20mA, 0-300psi 230.00AM316500 DCTG0500PT021 Pressure Transducer 1/4 NPT 4-20mA, 0-500psi 230.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

The Model DCT Transducer is designed for generalindustrial and commercial requirements offering ex-cellent performance over a wide range of applications.It is based on proven mico-machined silicon technolo-gy that offers high reliability, long-term stability, andlow cost relative to competing technologies. It com-bines precision pressure sensing with a rugged stain-less steel construction that allows it to operate reli-ably under the most extreme environmental condi-tions.

The Model DCT Pressure Transducer is available ina variety of mounting and electrical options and pres-sure ranges from 6 PSI to as high as PSI. It is fullydigitally compensated for effects of pressure and tem-perature changes and calibrated to produce industrystandard electrical outputs. The Model DCT acceptsboth unregulated and regulated excitation voltagesand provides output signals such as 1-5VDC, 1-6VDC,4-20mA, or a ratiometric 0.5 to 4.5VDC

The Model DCT is easy to install and maintain. Noadapters are required, and there is no need for fieldcalibration. It offers superior accuracy, below 0.25%span and below 1% over a wide compensated tempera-ture range. Its design incorporates a stainless steelisolation diaphragm and 316 SS construction for usewith most media types.

SPECIFICATIONSPressure Range Vacuum up to 500psigReference Accuracy ± 0.2% FS TYP, ±-.3 FS MAX

(Consult factory for ranges below 15psi)Total Error Band ± 1% FS(Includes temperature effects)1 Year Stability <0.25% FSOutputs 1-5VDC 1-6VDC 0.5-4.5VDC 4-20mAInput Supply Voltage 9-30VDC 9-30VDC 5VDC ± 5% Ratiometric 11-30VDCLoad Limitation 50KΩ Min. 50KΩ Min. 1MΩ Min. 500Ω Max.Operating Temperature -40 to 80° CProcess Temperature -40 to 125° CCompensated Temperature -25 to 75° COverpressure 2X FS or 750psig, whichever is lessBurst Pressure 3X FS or 750psig, whichever is lessVibration 10G, 55-2,000 Hz.Shock 30GEMC Rated 3V/m (Requires "PE" option)Process Wetted Material Brass, Borosilicate, Silicon, RTV, EpoxyElectronics Housing Material 1/8-27 NPT., 1/4-19 NPT.Electrical Connection Cable DIN Packard

• .20% accuracy typical .3%worst

• Excellent long term stability• Solid State / Industrial grade• Temperature compensated• Many ranges up to 500psi

• mv, 4-20mA, 1-5VDC, 1-6VDC output

• Vacuum and compound pres-sure ranges available

• Low cost

NIST it



H

Brass Digital Compensated Transducer

Catalog No. Model Description PriceAM300147 DCTC0030BPT022 Pressure Transducer 1/4 NPT 4-20mA, -14.7-30psi $185.00AM300060 DCTG0006BPT022 Pressure Transducer 1/4 NPT 4-20mA, 0-6psi 185.00AM300030 DCTG0030BPT022 Pressure Transducer 1/4 NPT 4-20mA, 0-30psi 185.00AM300100 DCTG0100BPT022 Pressure Transducer 1/4 NPT 4-20mA, 0-100psi 185.00AM300300 DCTG0300BPT022 Pressure Transducer 1/4 NPT 4-20mA, 0-300psi 185.00AM300500 DCTG0500BPT022 Pressure Transducer 1/4 NPT 4-20mA, 0-500psi 185.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

The Model DCT Transducer is designed for generalindustrial and commercial requirements offering ex-cellent performance over a wide range of applications.It is based on proven mico-machined silicon technolo-gy that offers high reliability, long-term stability, andlow cost relative to competing technologies. It com-bines precision pressure sensing with a rugged brassconstruction that allows it to operate reliably underthe most extreme environmental conditions.

The Model DCT Pressure Transducer is available ina variety of mounting and electrical options and pres-sure ranges from 6 PSI to as high as PSI. It is fullydigitally compensated for effects of pressure and tem-perature changes and calibrated to produce industrystandard electrical outputs. The Model DCT acceptsboth unregulated and regulated excitation voltagesand provides output signals such as 1-5VDC, 1-6VDC,4-20mA, or a ratiometric 0.5 to 4.5VDC

The Model DCT is easy to install and maintain. Noadapters are required, and there is no need for fieldcalibration. It offers superior accuracy, below 0.25%span and below 1% over a wide compensated tempera-ture range. Its design incorporates a diaphragm andbrass construction for use with most media types.

SPECIFICATIONSPressure Range Vacuum up to 500psigReference Accuracy ± 0.2% FS TYP, ±-.3 FS MAX

(Consult factory for ranges below 15psi)Total Error Band ± 1% FS(Includes temperature effects)1 Year Stability <0.25% FSOutputs 1-5VDC 1-6VDC 0.5-4.5VDC 4-20mAInput Supply Voltage 9-30VDC 9-30VDC 5VDC ± 5% Ratiometric 11-30VDCLoad Limitation 50KΩ Min. 50KΩ Min. 1MΩ Min. 500Ω Max.Operating Temperature -40 to 80° CProcess Temperature -40 to 125° CCompensated Temperature -25 to 75° COverpressure 2X FS or 750psig, whichever is lessBurst Pressure 3X FS or 750psig, whichever is lessVibration 10G, 55-2,000 Hz.Shock 30GEMC Rated 3V/m (Requires "PE" option)Process Wetted Material Brass, Borosilicate, Silicon, RTV, EpoxyElectronics Housing Material 1/8-27 NPT., 1/4-19 NPT.Electrical Connection Cable DIN Packard

• .20% accuracy typical .3% worst• Excellent long term stability• Solid State / Industrial grade• Temperature compensated• Many ranges up to 500psi• mv, 4-20mA, 1-5VDC, 1-6VDC output• Vacuum and compound pressure ranges available• Low cost

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

772

Industrial Pressure Transducers• Unparalleled Price/ Performance• Rugged Design Survives Harsh Environments• Operates Over a Wide Temperature Band• Compatible with Wide Range of Gases and Liquids• Operates on Low Cost Unregulated DC Power• Suitable for High Shock and Vibration Applications• No Seals or “O” Rings to Cause Leakage• No Brazed Joints Susceptible to Corrosion Problems• Meets CE Conformance Standards

The Model 209 pressure transducers have beendesigned specifically for industrial applicationsdemanding price and performance requirements.The 209 offers exceptional reliability in typical in-dustrial grade environments. Standard featurestailor the Model 209 for applications with moreextreme environmental conditions or more strin-gent performance needs. The transducers arepackaged in rugged stainless steel/Valox housings,which are small and lightweight for optimum com-patibility with system designs. As a totally self -contained electronic package, the 209 stainlesssteel capacitance sensing element, coupled with ahigh level output IC-based circuit, assures excel-lent accuracy and long term stability.

Catalog No. Model Description PriceSE 209100 2091030PC2M1102 Pressure Transducer, 4-20 mA output, -14.7 to 30 psig $185.00SE 209101 2091100PC2M1102 Pressure Transducer, 4-20 mA output, -14.7 to 100 psig 185.00SE 209102 2091005PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 5 psig 185.00SE 209103 2091010PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 10 psig 185.00SE 209104 2091025PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 25 psig 185.00SE 209105 2091050PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 50 psig 185.00SE 209106 2091100PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 100 psig 185.00SE 209107 2091250PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 250 psig 185.00SE 209108 2091500PG2M1102 Pressure Transducer, 4-20 mA output, 0 to 500 psig 185.00SE 209109 209110CPG2M1102 Pressure Transducer, 4-20 mA output, 0 to 1000 psig 185.00SE209110 2091030PC2M2402 Pressure Transducer, 5-5.5 VDC output, -14.7 to 30 psig 185.00SE209111 2091100PC2M2402 Pressure Transducer, 5-5.5 VDC output, -14.7 to 100 psig 185.00SE209112 2091005PG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 5 psig 185.00SE209113 2091010PG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 10 psig 185.00SE209114 2091025PG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 25 psig 185.00SE209115 2091050PG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 50 psig 185.00SE209116 2091100PG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 100 psig 185.00SE209117 2091250PG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 250 psig 185.00SE209118 2091500PC2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 500 psig 185.00SE209119 209110CPG2M2402 Pressure Transducer, 5-5.5 VDC output, 0 to 1000 psig 185.00AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

SPECIFICATIONSPerformance DataAccuracy ± 0.25% FS (RSS)Thermal EffectsZero Shift %FS/100°F(%FS/50°C) ± 2.0 (± 1.8)Span Shift %FS/100°F(%FS/50°C) ± 1.5 (± 1.3)Response Time 5 millisecondsElectrical Data (Voltage)Circuit 3-Wire (Com, Out, Exc)Excitation 9 to 30 VDCOutput 0.5 to 5.5 VDCElectrical Data (Current)Circuit 2-WireSupply Voltage 9 to 30 VDCOutput 4 to 20 mAEnvironmental DataTemperatureOperating Range°F -40 to + 185 (-40 to + 85)Compensated Range °F(°C) -4 to + 176 (-20 to + 80)Vibration 20gShock 200g Physical DescriptionCase Stainless Steel & ValoxSensor 17-4 PH Stainless SteelElectrical Connection 2 ft. multiconductor cablePressure Fitting 1/4” -18 NPT externalPressure Media Liquids or gases compatible

with 17-4 PH Stainless Steel

NIST it



H

NEMA 4/IP65 Gauge Pressure Transducer

Catalog No. Model Description PriceSE256100 2561025PG2M11 Pressure transducer, 4-20 mA output, 0-25 psig $249.00SE256101 2561050PG2M11 Pressure transducer, 4-20 mA output, 0-50 psig 249.00SE256102 2561100PG2M11 Pressure transducer, 4-20 mA output, 0-100 psig 249.00SE256103 2561250PG2M11 Pressure transducer, 4-20 mA output, 0-250 psig 249.00SE256104 2561500PG2M11 Pressure transducer, 4-20 mA output, 0-500 psig 249.00SE256105 256110CPG2M11 Pressure transducer, 4-20 mA output, 0-1,000 psig 249.00SE256106 256130CPG2M11 Pressure transducer, 4-20 mA output, 0-3,000 psig 249.00SE256107 256150CPG2M11 Pressure transducer, 4-20 mA output, 0-5,000 psig 249.00SE256108 256110KPG2M11 Pressure transducer, 4-20 mA output, 0-10,000 psig 249.00SE256109 2561025PG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-25 psig 249.00SE256110 2561050PG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-50 psig 249.00SE256111 2561100PG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-100 psig 249.00SE256112 2561250PG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-250 psig 249.00SE256113 2561500PG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-500 psig 249.00SE256114 256110CPG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-1,000 psig 249.00SE256115 256130CPG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-3,000 psig 249.00SE256116 256150CPG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-5,000 psig 249.00SE256117 256110KPG2M22 Pressure transducer, .1-5.1 VDC mA output, 0-10,000 psig 249.00AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

• High Accuracy• NEMA 4/IP65• Wide Operating Temperature Range• Compatible with a Wide Range of Gases or Liquids• Corrosive Resistant All Stainless Steel Wetted Parts • Choice of Voltage or Current Output• Operates on Low Cost Unregulated Power Supply• Meets CE Conformance Standards

SPECIFICATIONSPerformance DataAccuracy ± 0.13%FS(RSS) includes non-linearity,

hysteresis, non-repeatabilityEnvironmental DataTemperature Operating Range°F(°C) -40 to + 260 (-40 to + 125)Compensated Range°F(°C) -4 to + 176(-20 to + 80)Thermal EffectsZero/Span Shift %FS/°F(°C) ± 0.033 (± 0.06)Physical DescriptionCase Die-Cast AluminumElectrical Connections Terminal Strip with (4) 1/2” conduit portsPressure Fitting 1/4” NPT external Weight 13.4 ouncesPressure Media Liquids or gases compatible with

17-4 PH Stainless Steel. Electrical Data (Voltage)Circuit 3-Wire (Exc, Out, Com)Excitation 9 to 30 VDCOutput 0.1-5.1 VDCElectrical Data (Current)Circuit 2-WireSupply voltage 9 to 30 VDC Output 4-20 mA

The Model 256 is packaged in a die-cast aluminum en-closure that is specifically designed for NEMA4/IP65 ser-vice. The 256’s robust capacitive design is resistant to en-vironmental effects, such as shock, vibration, tempera-ture and EMI/RFI. Its stainless steel sensing elementdoes not require isolation from corrosive media.

Available in a wide variety of gauge pressure ranges,the 256 also features adjustable potentiometers for zeroand span settings..Only 3.6” high x 4.0” wide, the Model256 is designed for compact installations. The removablecover provides easy access to the internal terminal stripfor wiring. Installation is quick and easy with 1/2 inch in-ternal threaded conduit ports for electrical termination.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

774

Differential or Gauge Pressure Transducers

Catalog No. Model Description PriceSE267100 26710R1WD11G2HD Digital pressure transducer, 4-20 mA output, 0-.1"WC $315.00SE267101 2671R25WD11G2HD Digital pressure transducer, 4-20 mA output, 0-.25"WC 315.00SE267102 26710R5WD11G2HD Digital pressure transducer, 4-20 mA output, 0-.5"WC 315.00SE267103 2671001WD11G2HD Digital pressure transducer, 4-20 mA output, 0-1"WC 315.00SE267104 26712R5WD11G2HD Digital pressure transducer, 4-20 mA output, 0-2.5"WC 315.00SE267105 2671005WD11G2HD Digital pressure transducer, 4-20 mA output, 0-5"WC 315.00SE267106 2671010WD11G2HD Digital pressure transducer, 4-20 mA output, 0-10"WC 315.00SE267107 2671025WD11G2HD Digital pressure transducer, 4-20 mA output, 0-25"WC 315.00SE267108 2671050WD11G2HD Digital pressure transducer, 4-20 mA output, 0-50"WC 315.00SE267109 2671100WD11G2HD Digital pressure transducer, 4-20 mA output, 0-100"WC 315.00SE267110 26710R1WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-.1" WC 315.00SE267111 2671R25WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-.25" WC 315.00SE267112 26710R5WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-.5" WC 315.00SE267113 2671001WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-1" WC 315.00SE267114 26712R5WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-2.5" WC 315.00SE267115 2671005WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-5" WC 315.00SE267116 2671010WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-10" WC 315.00SE267117 2671025WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-25" WC 315.00SE267118 2671050WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-50" WC 315.00SE267119 2671100WD2DG2HD Digital pressure transducer, 0-5 VDC output, 0-100" WC 315.00AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

SPECIFICATIONSPerformance DataAccuracy ± .5% FS (RSS) Includes non-linearity,

hysteresis, and non-repeatability Maximum Line Pressure 10 PSIOverpressure 10 PSI in Positive or Negative DirectionThermal EffectsCompensated Temperature Range + 40 to + 140 °F (+ 5 to + 60 °C)Zero/Span Shift %FS/°F(°C) ± 0.033 (± 0.06) Operating Temperature Range 0 to + 150 °F (-18 to + 65 °C)Physical DescriptionCase IP65/NEMA 4 Plastic Glass-Filled

Polycarbonate UL94V-OElectrical Connection Terminal Strip Inside of CaseZero and Span Adjustment Accessible Inside of CasePressure Fittings 3/16” O.D. Barbed Brass for 1/4”

Push-On TubingElectrical Data (Voltage)Circuit 3-Wire (Exc, Gnd, Sig)

Protected from MiswiringExcitation 10.2 to 42 VDCOutput 0 to 5 VDCElectrical Data (Current)Circuit 2-Wire

Protected from MiswiringSupply Voltage 9 to 30 VDC Output 4 to 20 mAPressure Media Typically Air or Similar

Non-Conducting Gases

The Model 267 pressure transducers sensegauge (static) or differential pressure and convertthis pressure difference to a proportional electri-cal output. The 267 series is offered with a 0 to 5VDC output or 4-20 mA current output. The 267 isa single range unit and comes standard with a 31/2 digit LCD display. The 267 series has anIP65/NEMA 4 rated package to withstand envi-ronmental effects.

Used in Building Energy ManagementSystems, the 267 pressure transducer is availablefor air pressure ranges as low as 0.1 in W.C. fullscale to 100 in. W.C. full scale. Static accuracy is±1% full scale in normal ambient temperature en-vironments.

The rugged design allows up to 10 psi overpres-sure (in either direction), with no damage to theunit.

• 3 1/2 Digit LCD Display • .5 % FS Standard Accuracy• NEMA 4/IP65 Rated Housing• Ranges as low as 0.1 in. W.C. (25 Pa)• Meets CE Conformance Standards

NIST it



H

Differential or Gauge Pressure Transducers

Catalog No. Model Description PriceSE265100 2651R25WD11T1C Pressure transducer, 4-20 mA output, 0-.25" WC $150.00SE265101 26510R5WD11T1C Pressure transducer, 4-20 mA output, 0-.5" WC 150.00SE265102 2651001WD11T1C Pressure transducer, 4-20 mA output, 0-1" WC 150.00SE265103 26512R5WD11T1C Pressure transducer, 4-20 mA output, 0-2.5" WC 150.00SE265104 2651005WD11T1C Pressure transducer, 4-20 mA output, 0-5" WC 150.00SE265105 2651010WD11T1C Pressure transducer, 4-20 mA output, 0-10" WC 150.00SE265106 2651025WD11T1C Pressure transducer, 4-20 mA output, 0-25" WC 150.00SE265107 2651050WD11T1C Pressure transducer, 4-20 mA output, 0-50" WC 150.00SE265108 2651100WD11T1C Pressure transducer, 4-20 mA output, 0-100" WC 150.00SE265109 2651R25WD2BT1C Pressure transducer, 0-5 VDC, 0-.25" WC 150.00SE265110 26510R5WD2BT1C Pressure transducer, 0-5 VDC, 0-.5" WC 150.00SE265111 2651001WD2BT1C Pressure transducer, 0-5 VDC, 0-1" WC 150.00SE265112 26512R5WD2BT1C Pressure transducer, 0-5 VDC, 0-2.5" WC 150.00SE265113 2651005WD2BT1C Pressure transducer, 0-5 VDC, 0-5" WC 150.00SE265114 2651010WD2BT1C Pressure transducer, 0-5 VDC, 0-10" WC 150.00SE265115 2651025WD2BT1C Pressure transducer, 0-5 VDC, 0-25" WC 150.00SE265116 2651050WD2BT1C Pressure transducer, 0-5 VDC, 0-50" WC 150.00SE265117 265100WD2BT1C Pressure transducer, 0-5 VDC, 0-100" WC 150.00Accessories

NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

• 10 PSI proof pressure on all ranges• High level 0-5 VDC and 2-wire 4-20 mA analog

outputs are compatible with most energymanagement systems

• Fully protected against reverse wiring• Internal regulation permits use with unregulated DC

power supplies• Meets CE conformance standards

SPECIFICATIONSPerformance DataAccuracy ± 1.0% FS (RSS)Operating Range°F (°C) 0 to + 150 (-18 to + 65)Compensated Range °F(°C) 0 to + 150 (-18 to + 65) Thermal Effects %FS/°F(°C) ± .033% FS (.018% FS)Maximum Line Pressure 10 PSIOverpressure 10 PSI in Positive or Negative DirectionPhysical DescriptionCase Fire Retardent Glass Filled PolyesterElectrical Connection Screw Terminal StripPressure Fittings 3/16” OD Fitting for 1/4” ID TubingWeight 3 ouncesElectrical Data (Voltage)Circuit 3-Wire (Com, Out, Exc)Excitation 9 to 30 VDCOutput 0 to 5 VDC Electrical Data (Current)Circuit 2-WireSupply Voltage 12 - 30 VDCOutput 4 to 20 mAPressure Media Typically air or similar non-conducting gases.

The 265 pressure transducers sense differen-tial or gauge (static) pressures and convert thispressure difference to a proportional electricaloutput. The 265 is offered with a high level 0-5VDC output or a 4-20 mA output. Used inBuilding Energy Management Systems, thesetransducers are capable of measuring pressuresand flows with the accuracy necessary for properbuilding pressurization and air flow control. The265 Series very low pressure transducers areavailable for air pressure ranges as low as 0.25 in.WC full scale up to 100 in. WC full scale. Staticaccuracy is ±1% full scale in normal ambient tem-perature environments. The rugged design allowsup to 10 PSI overpressure (in either direction)with no damage to the unit. In addition, the sen-sor parts have thermally matched coefficients,which promote improved temperature perfor-mance and excellent long-term stability.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

776

Intrinsically Safe Pressure Transmitters

Catalog No. Range PriceStainless Steel CaseWKIS1030HGVAC 30 – 0 Inches Hg Vacuum $455.00WKIS100050INWC 0 – 50 Inches Water Column 385.00WKIS100100INWC 0 – 100 Inches Water Column 385.00WKIS1000005PSI 0 - 5 psi 385.00WKIS1000010PSI 0 - 10 psi 385.00WKIS1000015PSI 0 - 15 psi 385.00WKIS1000025PSI 0 - 25 psi 385.00WKIS1000030PSI 0 - 30 psi 385.00WKIS1000050PSI 0 - 50 psi 385.00WKIS1000060PSI 0 - 60 psi 385.00WKIS1000100PSI 0 - 100 psi 385.00WKIS1000160PSI 0 - 160 psi 385.00WKIS1000200PSI 0 - 200 psi 385.00WKIS1000250PSI 0 - 250 psi 385.00WKIS1025000PSI 0 - 25000 psi 1,145.00WKIS1040000PSI 0 - 40000 psi 1,145.00WKIS1000015PSIA 0 - 15 psi absolute 455.00WKIS1000025PSIA 0 - 25 psi absolute 455.00WKIS1000050PSIA 0 - 50 psi absolute 455.00

AccessoriesNISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00NISTPRQ132 NIST Traceable Certificate 148.00NISTPRQ133 NIST Traceable Certificate with Data 195.00

• Approvals pending for Class I Division 1 and Class I Zone 0 locationswhen used with an approved barrier

• 4-20 mA 2-wire output signal• Highly resistant to pressure spikes and vibration

SPECIFICATIONSAccuracy + 0.25% Best Fit Straight LineWetted Parts 316SS and PH17 – 4 SS (>= 400 psi)Case 316SSPressure Connection 1/2” NPT MalePower Supply 10 – 30 V DC Signal Output 4 – 20mA, 2-wire

The IS-10 industrial and IS-11 non-cloggingflush diaphragm pressure transmitters are de-signed for industrial pressure measurement appli-cations where intrinsically safe ratings are re-quired. Each transmitter undergoes extensivetesting and calibration to achieve an accuracy of0.25% full scale. State-of-the-art surface mounttechnology ensures that the unit is protectedagainst vibration, shock and humidity. Each unitis temperature compensated to assure accuracyand long-term stability under severe ambienttemperature variations.

The compact design features all stainless steelwetted parts and is available with a variety ofelectrical and process connections to meet specificinstallation requirements.

NIST it



H

Explosion Proof * Pressure Transmitters

Catalog No. Range Price

Stainless Steel CaseWKE1030HGVAC 30 Inches Hg Vacuum $379.00WKE1000015PSI 0 - 15 psi 329.00WKE1000030PSI 0 - 30 psi 329.00WKE1000060PSI 0 - 60 psi 329.00WKE1000100PSI 0 - 100 psi 329.00WKE1000200PSI 0 - 200 psi 329.00WKE1000300PSI 0 - 300 psi 329.00WKE1000500PSI 0 - 500 psi 329.00WKE1001000PSI 0 - 1000 psi 329.00WKE1001500PSI 0 - 1500 psi 329.00WKE1002000PSI 0 - 2000 psi 329.00WKE1003000PSI 0 - 3000 psi 329.00WKE1005000PSI 0 - 5000 psi 329.00WKE1008000PSI 0 - 8000 psi 329.00WKE1010000PSI 0 - 10000 psi 329.00WKE1015000PSI 0 - 15000 psi 329.00


• Explosion proof rating Approvals Pending• Available with 4-20 mA 2-wire or 1-5 Volt, or 0.5-4.5

ratiometric 3-wire output signals (voltage output at an additional cost)

• Engineered to meet the harsh demands of industrialapplications

• NACE approved wetted parts • Retrofits many existing applications

SPECIFICATIONSAccuracy ± 0.25% Best Fit Straight LineWetted Parts 316SS / ElgiloyCase 316SSPressure Connection 1/2” NPT MalePower Supply 10 – 30 V DC, 1/2”

Male conduit 5 foot cableSignal Output 4 – 20mA, 2-wire

Type E-10 explosion proof pressure transmit-ters are specifically designed to meet the durabili-ty and performance requirements of industrial ap-plications. These pressure transmitters featurean industry standard 4-20 mA 2-wire signal out-put, NEMA 4 (IP 67) weather protection, and areextremely resistant to pressure spikes, vibration,and moisture intrusion. The NACE approved wet-ted parts materials provide extra resistanceagainst sulfide stress cracking when exposed togases containing sulphur.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

*Approvals Pending


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

778

Pressure Transmitters

Catalog No. Range PriceStainless Steel Case, 1/4” NPT ConnectionWK4204833 0 - 100 Inches WC $195.00WK8363434 0 - 5 psi 195.00WK8363442 0 - 15 psi 195.00WK8363450 0 - 25 psi 195.00WK4256671 0 - 30 psi 195.00WK8363468 0 - 50 psi 195.00WK8363476 0 - 60 psi 195.00WK8363515 0 - 100 psi 195.00WK8363485 0 - 160 psi 195.00WK8363493 0 - 200 psi 195.00WK4256698 0 - 250 psi 195.00WK8363506 0 - 300 psi 195.00WK9697688 0 - 500 psi 195.00WK8357247 0 - 600 psi 195.00

SPECIFICATIONSAccuracy ± 0.50% Best Fit Straight LineWetted Parts 316SSCase 304SSPressure Connection 1/4” NPT MalePower Supply 10 – 30 V DCSignal Output 4 – 20mA 2-wire

WIKA C -10 pressure transmitters and trans-ducers are precision engineered to meet the priceand performance requirements of OriginalEquipment Manufacturers. Each unit undergoesextensive quality control testing and calibrationto achieve an accuracy < 0.50% full scale. Theprinted circuit boards use state-of-the-art surfacemount technology and are potted in silicone gel forprotection against mechanical shock, vibration,and moisture. Each unit is temperature compen-sated to assure accuracy and long- term stabilitywhen exposed to severe ambient temperaturevariations.

The C -10 provides a rugged design featuringexcellent vibration resistance and long servicelife. OEM applications include hydraulics, pneu-matics, press control, compressor control, pumpprotection and numerous other processing andcontrol operations.

Catalog No. Range PriceStainless Steel Case, 1/4” NPT ConnectionWK8357255 0 - 1000 psi $195.00WK8357264 0 - 1500 psi 195.00WK8357272 0 - 2000 psi 195.00WK8354753 0 - 3000 psi 195.00WK8347390 0 - 5000 psi 195.00WK8357280 0 - 7500 psi 195.00WK8357298 0 - 10000 psi 195.00WK8359576 0 - 15000 psi 195.00

AccessoriesNISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00NISTPRQ132 2 Year NIST Traceable Certificate 148.00NISTPRQ133 2 Year NIST Traceable Certificate with Data 195.000-5V, 1-5V, 0-10V 3-wire output options available

NIST it



H

Non-Incendive Pressure Transmitters

Catalog No. Range PriceStainless Steel CaseWKN1030HGVAC 30 Inches Hg Vacuum $345.00WKN1000015PSI 0 - 15 psi 295.00WKN1000030PSI 0 - 30 psi 295.00WKN1000060PSI 0 - 60 psi 295.00WKN1000100PSI 0 - 100 psi 295.00WKN1000200PSI 0 - 200 psi 295.00WKN1000300PSI 0 - 300 psi 295.00WKN1000500PSI 0 - 500 psi 295.00WKN1001000PSI 0 - 1000 psi 295.00WKN1001500PSI 0 - 1500 psi 295.00WKN1002000PSI 0 - 2000 psi 295.00WKN1003000PSI 0 - 3000 psi 295.00WKN1005000PSI 0 - 5000 psi 295.00WKN1008000PSI 0 - 8000 psi 295.00


SPECIFICATIONSAccuracy ± 0.25% Best Fit Straight LineWetted Parts 316SS / ElgiloyCase 316SSPressure Connection 1/4” NPT MalePower Supply 10 – 30 V DC,

1/2” Male conduit 5 foot cableSignal Output 4 – 20mA, 2-wire

The N-10 is FM approved non-incendive forClass I, Division II, Groups A, B, C, and D. Itfeatures a 1/2” male conduit electrical connec-tion, NACE listed wetted parts, NEMA 4 / IP67 weather protection, and excellent vibra-tion resistance.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

780

Sanitary Pressure Transmitters

Catalog No. Range PriceStainless Steel Case, 1.5” tri-clamp connectionWK9766329 30 - 0 Hg Vacuum $590.00WK8997395 30” - 0 - 30 psi 590.00WK9799732 30” - 0 - 60 psi 590.00WK4204387 30” - 0 - 100 psi 590.00WK9748202 0 - 15 psi 525.00WK9744703 0 - 30 psi 525.00WK4215789 0 - 50 psi 525.00WK9744703 0 - 60 psi 525.00WK9748237 0 - 100 psi 525.00WK9748245 0 - 160 psi 525.00

SPECIFICATIONSAccuracy ± 0.25% B.F.S.L.Wetted Parts 316SSCase 304SSPressure Connection 1.5” or 2” Tri-Clamp ConnectionsPower Supply 10 – 30 V DCSignal Output 4 – 20mA 2-wire

S-10-3A Sanitary Pressure Transmitters :WIKA S-10-3A pressure transmitters meet 3A

sanitary criteria for pressure and level measure-ment in the food, pharmaceutical, cosmetic, andbeverage industries. They feature 0.25% accura-cy, rugged stainless steel construction, and a wideoperating temperature range.

The 316 stainless steel flush diaphragm mini-mizes product buildup. The all welded chemicalseal system includes food grade liquid fill and isdesigned for “clean in place” (CIP) and “sterilize inplace” (SIP) maintenance procedures. The trans-mitters are available with industry standard 1.5”or 2” Tri-Clamp® connections.

Each transmitter undergoes extensive qualitycontrol testing and calibration. The printed cir-cuit boards use state-of-the-art surface mounttechnology and are potted in silicone gel for pro-tection against mechanical shock, vibration, andmoisture. Each transmitter is temperature com-pensated to assure accuracy and long-term stabili-ty when exposed to severe ambient temperaturevariations.

Catalog No. Range PriceStainless Steel Case, 1.5” tri-clamp connectionWK9749408 0 - 200 psi $525.00WK9776227 0 - 250 psi 525.00WK8990985 0 - 300 psi 525.00WK4205081 0 - 500 psi 525.00WK8993470 0 - 1000 psi 525.00


NIST it



H

41⁄2 “ Duratran Pressure Transmitter

Catalog No. Bourdon Tube / Range PriceTip Material

AS775923 316 Stainless Steel 0-30 psi $450.00AS775924 316 Stainless Steel 0-100 psi 450.00AS775925 316 Stainless Steel 0-200 psi 450.00AS775927 316 Stainless Steel 0-1000 psi 450.00Catalog No. Model DescriptionML428271 2400 Process Power Pack 24VDC-175mA 130.90NISTPR32 — NIST Traceable Certificate 99.00NISTPR33 — NIST Traceable Certificate with Data 130.00

The Duratran® transmitter introduces a uniqueelectronic pressure-indicating transmitter withdirect mechanical indication suitable for aggres-sive environments and process fluids.

The Duratran transmitter combines outstand-ing, reliable local indication that functions with-out the need for external power with a stable, self-contained 4/20mA transmitter in a hermeticallysealed corrosion-proof case (Type 2279).

The wide selection of system materials and cor-rosion-proof housing meets application require-ments in a number of industries. These includechemical processing, petrochemical and refiningplants, electric and gas utilities, wastewater andother industrial applications.

This electronic pressure-indicating transmitterpromises increased service life and long-term stability.

• ± 0.5% of full-scale accuracy• Ranges from 12 to 20,000 psi• 4-20mA, 2-wire output

• Zero and span adjustments• FM approved intrinsically safe• 41⁄2" solid-front phenolic case

SPECIFICATIONSFunctional Service Liquid, gas or vaporRanges See ordering informationOutput 4-20mA, 2 wirePower Supply 12/40 VdcZero Adjustment ± 20% of full scaleSpan Adjustment ± 10% of full scaleTemperature Limit -40°F to 160°FOverpressure Limits 130% of range without damage to tubeHumidity Limits Up to 90% relative humidity noncondensingSignal Damping Fixed electronic damping time constant of

0.2 secondsTurn On Time Less than 1 secondEnclosure NEMA 4Agency ApprovalFactory Mutual approved as intrinsically safe for Class I, II and III, Division1, applicable Groups A, B, C, D, E and G in accordance with Dresserdrawing 71B185 and entity requirements; nonincendive for Class, I, II, III,Division 2, Groups A, B, C, D and G hazardous locations.* 0-20000 psi range not FM approvedPERFORMANCEAccuracy ± 0.5% including linearity, hysteresis and

repeatabilityStability ± 0.25% F.S. for 6 monthsTemperature Effect Less than 0.02% of span/°FPosition Effect Vertical mounting recommended

May be re-zeroed to correct error in otherpositions

PHYSICALDial Size 41⁄2"Case Solid front, black phenolic hermetically

sealedRing Threaded, glass-filled polypropyleneMounting Stem, surface, flush (with 1278 M ring)Pressure Connection 1⁄2 NPTWindow Laminated safety glassCalibration Transmitter — Span and zero adjustment

on dialGauge -- Zero adjustment with micrometerpointer

Electrical Connection 30" #18 wire AWG, 1⁄2 NPT liquid tightconduit connection at case

Weight 3 lb

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

782

P to I (Pressure to Current) Convertor

• Please specify input pressure range of( 3-15 psig; 3-27 psig or 6-30 psig or 0-30 psi; 0-100 psi; 0-6 psi; or 0-12 psi)• Specify output format (-B = 4-20 mA; -C = 10-50mA)[example: x55 - 302 - (3 - 15) -B-SM]

Catalog No. Model Description PriceRN474141 X55-302 (input) (output)-SM General Purpose module w/ surface mount base $283.00RN474142 X55-302-(input)-(output)-DIN General Purpose module W/32 mm "G" style DIN base 283.00RN474143 X55302-(input)-(output)-D2 General Purpose module w/35 mm "U" style DIN base 289.00RN474144 X55-302-EXP(input) (output) Explosion proof module and base 452.00RN474145 X55-302-M (input) ( output) Replacement module only w/o/ base 248.00Four wire (24 vdc powered ) P/i Transmitter• Please specify input pressure range (3-15 psi; 3-27 psi; 6-30 psi; 0-100 psi; 0-6 psi; 0r 0-12 psi)• Specify output format (-B = 4-20 mA; -C = 10-50 mA; -D = 1-5 vdc; -E = 2-10 vdc; -F = 0-5 vdc; -G = 0-10 vdc)RN474146 (input) (output)X55-304- SM General Purpose module W/ surface mount base 341.00RN4741447 (input) (output)X55304 - DIN General Purpose module W/32mm "G" style base 341.00RN474148 (input) (output)X55-304-D2 General Purpose module W/ 35mm "U' style base 348.00RN474149 (input) (output) X55-304-EXP Explosion Proof module and base 514.00RN474150 (input) (output)X55-304-M Replacement module only w/o base 307.00X55-302/304 Mounting Hardware and AccessoriesRN474151 X55-300-SM Replacement surface and mount base only 37.00RN474152 X55-300-DIN Replacement 32mm "G' style DIN rail base only 37.00RN474153 X55-300-D2 Replacement 35mm "U" style DIN rail base only 39.00RN471454 X55-300-EXP Replacement explosion proof housing and base only 182.00RN471455 X55-300-SSTAG Stainless steel tag 19.00RN471456 X55-300-PMB 2" pipe mount bracket (epoxy painted) 19.00RN471457 X55-300-PMB 2" 304 stainless steel pipe mount bracket 61.00RN474137 DI-32X15 32mm "G" style rail, (order per foot) 6.50RN474138 D2-35X7.5 35mm X7.5 "u" style DIN rail, (order per foot) 5.00RN474139 D2-35X15 35mm X 15 mm "u" style DIN rail, (order per foot) 6.50RN474158 X55-300-MF-DI Conversion kit, SM or 35mm DIN to 32mm DIN 17.00RN474159 X55-300-MF-D2 Conversion kit, SM or 32mm DIN to 25mm DIN 17.00NISTDT01 — NIST Traceable Certificate 75.00NISTDT02 — NIST Traceable Certificate with Data 125.00NISTDTQ01 — 2 Year NIST Traceable Certificate 112.00NISTDQ02 — 2 Year NIST Traceable Certificate with Data 187.00

• Detachable electronic module for easier and faster calibration and system maintenance

• Solid-state design for higher accuracy, faster response and betterprocess control

• Front access test jacks and alarm indicatorssimplifies calibration and reduces down-time

• Two or four-wire models

• 5 ranges up to 100 psig• Insensitive to vibration and mounting position• Front accessible zero, span and setpoint adjustments• Loss-of-air alarm indicator and output signal• Optional high or low pressure adjustable setpoint• 3-times maximum rated pressure without damage

The X55-300 Series P to I Convertors convertinstrument air pressures to analog current or volt-age signals. The two and four-wire models areboth available with five common input rangesfrom 3-15 psig to 0-100 psig. A solid-state sensorassures you of outstanding linearity, negligiblehysteresis, very fast response times and excellenttemperature stability.

The electronics portion of our P to I Convertorcan be removed from the pneumatic base withoutloss of air pressure. The means you can performsimple calibration and regular maintenance with-out purging the air lines. Simple to install andmaintain, the X55-300 features output monitoringtest jacks, a loss-of-air alarm (on elevated zerounits only), an adjustable setpoint alarm optionand front access calibration.

NIST it



H

I to P (Current to Pressure) Transducers

• No pre-regulator need for lower installation and maintenance costs• Low air consumption for lower compressor loads and lower running

costs• Hard-to-plug-design for less “down time“ and lower maintenance costs• Selectable input ranges of 4-20 mA or 10-50 mA• Output pressure of 3-15 psig, 3-27 psig and 6-30 psig• Selectable direct or reverse acting modes• Can be mounted in any position• Vibration resistant• Selectable split ranging in direct or reverse mode• Operating temperature range -40° to 150° F• Intrinsic Safety, Explosion Proof and Division 2 approvals are standard

NIST it


I to P Modules (Please specify range of 3-15 psig, 3-27 psig or 6-30 psig)

RN474110 X55-600-GP-SM General purpose $335.00surface mount

RN474111 X55-600-GP-DIN General purpose 335.00DIN rail-mount

RN474112 X55-600-GP-M General purpose 335.00manifold mount (without base)

RN474113 X55-600-GP-D2 General purpose 340.0035mm rail mount

RN474114 X55-600-N4-SM NEMA 4 General purpose 360.00surface mount

RN474115 X55-600-N4-DIN NEMA 4 General purpose 365.00DIN rail mount

RN474116 X55-600-N4-D2 NEMA 4 General purpose 365.0035mm rail mount

RN474117 X55-600-EX-SM NEMA 4 Explosion proof 505.00surface mount

Manifold Chassis

RN474120 X55-600-SMC-4 4 position surface mount 220.00manifold chassis

RN474121 X55-600-SMC-8 8 position surface mount 440.00manifold chassis

Catalog No. Model Description PriceRN474122 X55-600-SMC-10 10 position surface mount $550.00

manifold chassisRN474123 X55-600-RM-8 8 Position, 19" rack mount 495.00

manifold chassis

AccessoriesRN474130 X55-600-UMB Universal mounting bracket 20.50

(use with surface mount units only)RN474131 X55-600-PMB 2" Pipe mount bracket 27.00

(use with surface mount units only)RN474132 X55-77-4 Filter/Preregulator 130.00RN474133 X55-0-30 Pressure gauge (0-30 psi) 35.00RN474134 X55-0-60 Pressure gauge (0-60 psi) 40.00RN474135 X55-600-MF-D1 Conversion kit, SM or 20.50

35mm DIN to Standard DINRN474136 X55-600-MF-D2 Conversion kit, SM or 20.50

standard DIN to 35mm DINRN474137 D1-32x15 32mm x 15mm “G” style rail, 5.10

per foot (specify length)RN474138 D2-35x7.5 35mm x 7.5mm “U” style rail, 3.80

per foot (specify length)RN474139 D2-35x15 35mm x 15mm “U” style rail, 5.10

per foot (specify length)RN474140 X55-600-SS TAG Stainless steel tag 23.00NISTDT01 — NIST Traceable Certificate 75.00NISTDT02 — NIST Traceable Certificate with Data 125.00

I to P (Current to Pressure) TransducersThe X55-600 Series “Hard to Plug“ I to P transducers

are state of the art and feature field selectable inputcurrent ranges of 4-20 mA and 10-50 mA for standardoutput pressures of 3-15 psig, 3-27 psig and 6-30 psig.Utilizing advanced solid state technology and feedbackcontrol, the X55-600 series provides high reliability andexceptional output accuracy over a wide temperaturerange. The unit features minimal vibration sensitivity(less than ±1% of span at 1 g from 5 to 2000 Hz) and canbe mounted in any directional position. The X55-600provides fast system response by providing from 3SCFM to as much as 10 SCFM flow capacity at 100 psisupply air pressures.

TYPE 1001 NEMA 4X Explosion-Proof Housing



H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

784

I/P (Current to Pressure) & E/P (Voltage to Pressure) Transducers

TYPE 1001 I/P & E/P• 0.1% accuracy typical• Zero-based output models available• NEMA 4X explosion-proof models available • Intrinsically safe (FM / CSA)• Built in volume booster provides flows up to 12 SCFM• Mounts at any angle (except Nema 3R)• Low air consumption• Removable orifice (restrictor) for easy maintenance• Bottom port units available• CE approval• Vibration Insensitive

TYPE 2000 I/P & E/P• High precision, 0.1% accuracy typical • Vibration and position insensitive• Reliable, simple piezo ceramic beam actuator• DIP switches permit field selection of inputs and direct/reverse/split

ranging• Very wide selection of input and output ranges• Precise, reliable performance under extreme

conditions of temperature, vibration, orientation, supply pressure changes, supply voltage changes, RFI/EMI, humid / oil-laden media and corrosive surroundings

• Standard model is Nema 4x (weatherproof) Explosion proof model–also Nema 4x

TYPE 1001 NEMA 4X

TYPE 2000 NEMA 4X

TO ORDER, SEE NEXT PAGE



H

Catalog No. Model Description Range PriceType 1001 I/P MB966020 966-020-000 General Purpose Panel or Bracket Mount 4-20 mA / 3-15 psig $508.20MB966030 966-030-000 General Purpose Panel or Bracket Mount 4-20 mA / 3-27 psig 508.20MB966040 966-040-000 General Purpose Panel or Bracket Mount 4-20 mA / 6-30 psig 508.20MB966060 966-060-000 General Purpose Panel or Bracket Mount 4-20 mA / 0-15 psig 538.20MB966090 966-090-000 General Purpose Panel or Bracket Mount 4-20 mA / 0-100 psig 538.20MB968021 968-021-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 4-20 mA / 3-15 psig 693.00MB968031 968-031-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 4-20 mA / 3-27 psig 693.00MB968041 968-041-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 4-20 mA / 6-30 psig 693.00MB968061 968-061-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 4-20 mA / 0-15 psig 723.00MB968091 968-091-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 4-20 mA / 0-100 psig 723.00Type 1001 E/P MB966620 966-620-000 General Purpose Panel or Bracket Mount 0-10 VDC / 3-15 psig 508.20MB966630 966-630-000 General Purpose Panel or Bracket Mount 0-10 VDC / 3-27 psig 508.20MB966640 966-640-000 General Purpose Panel or Bracket Mount 0-10 VDC / 6-30 psig 508.20MB966660 966-660-000 General Purpose Panel or Bracket Mount 0-10 VDC / 0-15 psig 538.20MB966690 966-690-000 General Purpose Panel or Bracket Mount 0-10 VDC / 0-100 psig 538.20MB968621 968-621-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 0-10 VDC / 3-15 psig 693.00MB968631 968-631-000 Nema 4X Explosion Proof Pipe, Panel, or Bracket Mount 0-10 VDC / 3-27 psig 693.00MB968641 968-641-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 0-10 VDC / 6-30 psig 693.00MB968661 968-661-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 0-10 VDC / 0-15 psig 723.00MB968691 968-691-000 Nema 4X Explosion Proof Pipe, Panel or Bracket Mount 0-10 VDC / 0-100 psig 723.00Type 2000 I/P MB24231 2KSNNF42DF31500 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 4-20 mA / 3-15 psig 425.00MB24232 2KSNNF42DF32700 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 4-20 mA / 3-27 psig 425.00MB24233 2KSNNF42DF63000 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 4-20 mA / 6-30 psig 425.00MB24234 2KSNNF42DF01500 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 4-20 mA / 0-15 psig 425.00MB24235 2KSNNF42DF10000 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 4-20 mA / 0-100 psig 425.00MB24236 2KENNF42DF31500 Nema 4X, Explosion Proof Pipe, Panel or Bracket 4-20 mA / 3-15 psig 500.00MB24237 2KENNF42DF32700 Nema 4X, Explosion Proof Pipe, Panel or Bracket 4-20 mA / 3-27 psig 500.00MB24238 2KENNF42DF63000 Nema 4X, Explosion Proof Pipe, Panel or Bracket 4-20 mA / 6-30 psig 500.00MB24239 2KENNF42DF01500 Nema 4X, Explosion Proof Pipe, Panel or Bracket 4-20 mA / 0-15 psig 500.00MB24240 2KENNF42DF10000 Nema 4X, Explosion Proof Pipe, Panel or Bracket 4-20 mA / 0-100 psig 500.00Type 2000 E/P MB24241 2KSNNF01DF31500 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 0-10 VDC / 3-15 psig 425.00MB24242 2KSNNF01DF32700 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 0-10 VDC / 3-27 psig 425.00MB24243 2KSNNF01DF63000 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 0-10 VDC / 6-30 psig 425.00MB24244 2KSNNF01DF01500 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 0-10 VDC / 0-15 psig 425.00MB24245 2KSNNF01DF10000 Nema 4X, Intrinsically Safe Pipe, Panel or Bracket 0-10 VDC / 0-100 psig 425.00MB24246 2KENNF01DF31500 Nema 4X, Explosion Proof Pipe, Panel or Bracket 0-10 VDC / 3-15 psig 500.00MB24247 2KENNF01DF32700 Nema 4X, Explosion Proof Pipe, Panel or Bracket 0-10 VDC / 3-27 psig 500.00MB24248 2KENN F01DF63000 Nema 4X, Explosion Proof Pipe, Panel or Bracket 0-10 VDC / 6-30 psig 500.00MB24249 2KENNF01DF01500 Nema 4X, Explosion Proof Pipe, Panel or Bracket 0-10 VDC / 0-15 psig 500.00MB24250 2KENNF01DF10000 Nema 4X, Explosion Proof Pipe, Panel or Bracket 0-10 VDC / 0-100 psig 500.00Accessories Type 1001 & 2000MB010135 010-135-000 Panel Mounting Kit 4.00MB010134 010-134-000 Valve Mounting Kit 8.00MB010143 010-143-000 2" Pipe Mounting Kit 8.00MB010115 010-115-000 DIN Rail Adaptor 5.00NISTDT01 — NIST Traceable Certificate — 75.00NISTDT02 — NIST Traceable Certificate with Data — 125.00NISTDTQ01 — 2 Year NIST Traceable Certificate — 112.00NISTDTQ02 — 2 Year NIST Traceable Certificate with Data — 187.00

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

786

I/P (Current to Pressure) & E/P (Voltage to Pressure) Transducers• Built-in booster provides flow capacity up to

12 SCFM• Small size, light weight• Field reversible• Explosion-proof and

intrinsically safe models available

• Low Air Consumption• Mounts at any angle• Convenient external

span and zero adjusts• Wide supply pressure range• Low supply pressure sensitivity• CE approval

Catalog No. Model Description Range PriceType 1000 I/P MB961070 961-070-000 General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 3-15 psig $285.00MB961074 961-074-000 General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 3-27 psig 285.00MB961075 961-075-000 General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 6-30 psig 285.00MB961117 961-117-000 General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 2-60 psig 338.45MB961111 961-111-000 General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 3-120 psig 338.45MB961098 961-098-000 Nema 4x, Explosion Proof Pipe, Panel or Bracket Mount 4-20 mA / 3-15 psig 528.89Type 1000 E/P MB961085 961-085-000 General Purpose Pipe, Panel or Bracket Mount 1-9 VDC / 3-15 psig 285.00MB961086 961-086-000 General Purpose Pipe, Panel or Bracket Mount 1-9 VDC / 3-27 psig 285.00MB961087 961-087-000 General Purpose Pipe, Panel or Bracket Mount 1-9 VDC / 6-30 psig 285.00MB961118 961-118-000 General Purpose Pipe, Panel or Bracket Mount 0-5 VDC / 2-60 psig 338.45MB961112 961-112-000 General Purpose Pipe, Panel or Bracket Mount 0-10 VDC / 3-120 psig 338.45MB961142 961-142-000 Nema 4X, Explosion Proof Pipe, Panel or Bracket Mount 1-9 VDC / 3-15 psig 528.89

TYPE 1000 General Pruposecut-away

TYPE 1000 General Prupose

Save 50%on 2nd year

recalibration

Ask about2 YearNIST




H

Catalog No. Model Description Range PriceType 1500 I/P MB969710 969-710-000 Indoor Use, General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 3-15 psig 285.00MB969713 969-713-000 Indoor Use, general Purpose Pipe, Panel or Bracket Mount 4-20 mA / 0-15 psig 285.00MB969716 969-716-000 Indoor Use, General Purpose Pipe, Panel or Bracket Mount 4-20 mA / 0-120 psig 340.00MB966710 966-710-000 Nema 4X Pipe, Panel or Bracket Mount 4-20 mA / 3-15 psig 339.00MB966713 966-713-000 Nema 4X Pipe, Panel or Bracket Mount 4-20 mA / 0-15 psig 339.00MB966716 966-716-000 Nema 4X Pipe, Panel or Bracket Mount 4-20 mA / 0-120 psig 394.00Type 1500 E/P MB969750 969-750-000 Indoor Use, General Purpose Pipe, Panel or Bracket Mount 0-10 VDC / 3-15 psig 285.00MB969753 969-753-000 Indoor Use, General Purpose Pipe, Panel or Bracket Mount 0-10 VDC / 0-15 psig 285.00MB969756 969-756-000 Indoor Use, General Purpose Pipe, Panel or Bracket Mount 0-10 VDC / 0-120 psig 340.00MB966750 966-750-000 Nema 4X Pipe, Panel or Bracket Mount 0-10 VDC / 3-15 psig 339.00MB966753 966-753-000 Nema 4X Pipe, Panel or Bracket Mount 0-10 VDC / 0-15 psig 339.00MB966756 966-756-000 Nema 4X Pipe, Panel or Bracket Mount 0-10 VDC / 0-120 psig 394.00AccessoriesMB010134 010-134-000 Type 1000 Valve Mounting 8.00MB010143 010-143-000 Type 1000 2” Pipe Mounting Kit 8.00MB010606 010-606-000 Type 1500 3 Station Manifold Kit 191.00MB0106061 010-606-001 Type 1500 5 Station Manifold Kit 301.00MB0106062 010-606-002 Type 1500 10 Station Manifold Kit 360.00MB010602 010-602-000 Manifold Adaptor Kit 88.00MB971140 971-140-000 DIN Rail Kit 8.00NISTD01 — NIST Traceable Certificate 75.00NISTD02 — NIST Traceable Certificate with Data 125.00NISTDTQ01 — 2 Year NIST Traceable Certificate 112.00NISTDTQ02 — 2 Year NIST Traceable Certificate 187.00

• 3,5, & 10 unit Manifolds Available• Manifold mounting with ports on front & back of unit• Low air consumption• Field reversible• Small footprint, compact• CE Approval (conduit version only)

• FM, CSA, CENELEC intrinsically safe (option)• Durable weatherproof NEMA 4X housing (option)• Built in Volume Booster provides 7 SCFM @ 15psi / 1.0 BAR• Wide selection of input and output ranges from

0 to 120 psi / 8.3 BAR• Conduit fittings, terminal block, DIN connectors

TYPE 1500 I/P & E/P

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

788

Precision Air Regulators & Filter Regulators

Catalog No. Model Description Range PriceType 50 Filter RegulatorsMB960067 960-067-000 General Purpose Air Filter Pipe, 0-30 psig, 40 Micron Filter $46.58

Panel or Bracket MountMB960068 960-068-000 General Purpose Air Filter Pipe, 0-60 psig, 40 Micron Filter 46.58

Panel or Bracket MountMB960069 960-069-000 General Purpose Air Filter Pipe, 0-120 psig, 40 Micron Filter 46.58

Panel or Bracket MountType 51FR Filter RegulatorsMB960175 960-175-000 Compact, Low Cost, Air Filter Regulator 0-30 psig, 40 Micron Filter 46.58

Pipe, Panel or Bracket MountMB960176 960-176-000 Compact, Low Cost, Air Filter Regulator 0-60 psig, 40 Micron Filter 46.58

Pipe, Panel or Bracket MountMB960177 960-177-000 Compact, Low Cost, Air Filter Regulator 0-100 psig, 40 Micron Filter 46.58

Pipe, Panel or Bracket MountType 70 Air RegulatorsMB960129 960-129-000 Precision, High Flow Air Regulator, Pipe, 0-2 psig

Panel or Bracket Mount 70.38MB960130 960-130-000 Precision, High Flow Air Regulator Pipe, 0-10 psig




Panel or Bracket Mount 66.24

High Flow & High Pressure Gas RegulatorsType P37• Balanced pintle design• Bubble tight / non-relieving• 16.5 Mbtu/hr. (110 SCFM)• UL Pending• AGA/CGA pending• Bellofram rolling diaphragm• High flow capacity• Enclosed space use• High volume applications

Type 50• Superior regulation

characteristics• Rugged, corrosion-

resistant construction• Self-relieving• Integral, 40 micron,

self cleaning filter• Several mounting

options• Low cost

Type 51FR• Excellent regulation, sta-

bility and repeatability• Corrosion-resistant

construction (no brasscomponents)

• Low cost• Small package size• Panel, bracket or pipe

mounting

Type 70• High flow capacity - Up to 80 SCFM• Responds quickly to minute changes in downstream

pressure• Dampening action of aspirator tube helps maintain

downstream pressure• Balanced supply valve minimizes the effect of supply

pressure changes• Stack up construction can be disassembled and

serviced without removal from air line

Catalog No. Model Description Range PriceP-37 MB960370 960-370-000 High Flow LP Gas Regulator 0-10 psig $75.00MB960372 960-372-000 High Flow LP Gas Regulator 0-30 psig $75.00MB960374 960-374-000 High Flow LP Gas Regulator 0-60 psig $75.00MB960376 960-376-000 High Flow LP Gas Regulator 0-125 psig $75.00P-39MB9603441 960-344-001 High Pressure, Solid Brass Regulator 0-120 psig $105.00

for Natural Gas & PropaneMB9603443 960-344-003 High Pressure, Solid Brass Regulator 0-150 psig $105.00



for Natural Gas & Propane

Type P39• High Inlet Pressure up to

5500 psig• Output Pressure range of

0 to 500 psig• Forged Brass with 302 Stainless

Diaphragm• Nylon or CTFE Seat• Also available in elektroless nickel

plating and stainless steel



H

The Dwyer Series 605 Magnehelic® indicating transmitter simul-taneously provides local indication on a large, easily read analogscale while also converting that pressure into a standard two-wire, 4 to 20 mA signal for ranges from 0 to 1 to 0 to 10" w.c.

Positive, negative or differential air and compatible gaspressure can be measured with an accuracy of ±2% of fullscale. The basic mechanical components of the Series 605Magnehelic® indicating transmitter are similar to thoseused in the popular, time-proven Magnehelic® differentialpressure gauge. However, the Series 605 models add elec-trical conditioning and amplification of a resistancechange produced by a silicon strain gauge which is ce-mented to the range spring. This resistance change is theresult of the slight flexing which results from spring de-flection as pressure is applied to the diaphragm whichis directly linked to thespring. Refer to bulletinE-50 for additional in-formation on the design,operation and con-struction of theMagnehelic® indicatingtransmitter.

Differential Pressure Transmitter/Indicator4-20 mA Signal For Low Air Or Gas Pressure Positive, Negative or Differential

SPECIFICATIONSGENERALMaximum Pressure 25 psigMedia Compatibility Air & non-combustible, non-corrosive gasesELECTRICALPower Supply 12 to 35 VDCConnections 2 screw terminal block, positive & negativeOutput Signal 4-20 mA DC (limited at 38 mA)Loop Resistance 0 to 1170ΩWarm-up Time 5-10 minutesCurrent Consumption 38 mA max. DCPERFORMANCE AT ROOM TEMPERATUREZero Output 4 mAFull Scale Span 16 mAStatic Accuracy ± 2% SpanSpan & Zero Adjustable to 0.05%Repeatability 0.5% SpanResolution InfinitesimalENVIRONMENTALOperating Temperature 20 to 120°F (dry air)Compensated Temperature 30 to 120°FThermal Errors ± 1%/50°FMECHANICALWeight 1 lb., 10 oz.Span & Zero Adjustments protected potentiometers,

externally accessiblePressure Connections 1⁄8"-27 NPT Female

Standard accessories• Mounting ring• Snap ring• (4) 6-32 x 11⁄4 screws (panel mount)• (3) 6-32 x 5⁄16 screws (surface mount)• (2) Tubing to 1⁄8" NPT adapters• 1⁄8" NPT plugs• Adjustment key

SERIES 605 MODELS AND RANGESModel Range MinorNumber Inches w.c. Divisions605-1 0 to 0.1 .02605-2 0 to 2.0 .05605-3 0 to 3.0 .10605-6 0 to 6.0 .20605-10 0 to 10 .20

NIST it





supply


Catalog No. Model Description PriceDW336501 605-1 0-1" W.C. Gage $186.50DW336502 605-2 0-2" W.C. Gage 186.50DW336503 605-3 0-3" W.C. Gage 186.50DW336504 605-6 0-6.0" W.C. Gage 186.50DW336505 605-10 0-10" W.C. Gage 186.50PD885100 PD690-3-N Digital Indicator 117VAC 229.00PD885105 PD690-3-18 Digital Indicator 117VAC with 4 relay 478.00

output and 4-20mA NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00For additional digital indicators, Pease see page 143


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

790

The Series 634E Transmitters sense a single air compatiblegas or liquid pressure and produce a standard 4-20mA outputsignal. Sensitive silicon strain gauge measures within ±2%F.S.O. Convenient two wire operation simplifies installationand expands application flexibility over comparable three orfour wire units. Zero and span adjustments are fully protectedinside a rugged die cast aluminum housing with an attractive,durable, gray polyurethane finish. Enclosure is designed tomeet NEMA 4X requirements.

Range in PSI Range in PSI Range in PSICatalog No. Model As stocked Min. range Max. range PriceDW182007 634E-0 0-10 0-5 0-20 $199.00

DW182008 634E-1 0-30 0-20 0-60 199.00

DW182009 634E-2 0-100 0-50 0-200 199.00

DW1820010 634E-3 0-500 0-200 0-800 199.00

DW1820011 634ES1-7 0-1000 0-800 0-2000 199.00

DW1820012 634E-5 0-2000 0-1500 0-6000 199.00

ML428271 2400 Process Power Pack 24Vdc-175mA 130.90



SPECIFICATIONSMaximum pressure 1.5 x maximum rangeMedia compatibility Air and non-corrosive gases and liquidsHousing Designed to meet NEMA-4XPower supply 12.3 to 35 VDCOutput signal 4-20mADC, 2 wire (limited at 39mA maximumLoop resistance 0-1135Ω from 12.3 to 35 VDCCurrent consumption 38mADC (maximum)Die cast aluminum with textured gray polyurethane finish, beryllium copper Bourdon tube,brass pressure connection.Weight 1 lb, 12 oz. (8 kg.)Span and zero adjustments Protected potentiometers, located in auxiliary housingPressure connection 1⁄4" NPTF x 1⁄2" NPTMPERFORMANCE AT 70°F (21.1°C)Zero output 4mADCFull span output 20mADCAccuracy ±2% of full scale outputSpan and zero Adjustable to 0.05% of full spanWarm-up time 10 minutes

Pressure Transmitter with NEMA 4X Enclosure4-20mA signal, two wire operation, ranges to 6000 PSI

NIST it

Pressure range Model T10 Model T20 Model T30 Model T40(10-30VDC In / 0-5VDC Out) (120 VAC In / 0-5VDC Out) (10-30VDC In / 4-20 mA Out) (120 VAC In / 4-20 mA Out)

0-0.1˝ H2O MS191221 MS191191 MS1912011 MS1914010-0.5˝ H2O MS191224 MS191194 MS1912014 MS1914040-1.0˝ H2O MS191225 MS191195 MS1912015 MS1914050-3.0˝ H2O MS191227 MS191197 MS1912017 MS1914070-5.0˝ H2O MS191228 MS191198 MS1912018 MS1914080-10.0˝ H2O MS191229 MS191199 MS1912019 MS1914090-30.0˝ H2O MS191231 MS191201 MS1912021 MS1914120-50.0˝ H2O MS191232 MS191202 MS1912022 MS1914130-3.0 PSID MS191236 MS191206 MS1912026 MS1914170-5.0 PSID MS191237 MS191207 MS1912027 MS1914180-15.0 PSID MS191238 MS191208 MS1912028 MS1914190-30.0 PSID MS191239 MS191209 MS1912029 MS191420Price $275.00 $275.00 $275.00 $275.00AccessoriesNISTPR132 NIST Traceable Certificate 99.00NISTPR133 NIST Traceable Certificate with Data 130.00

Differential Pressure Transmitters NIST it

• Virtually position insensitive even at very low pressure (0.01")• Fast response time due to low internal volume• 1 Year warranty

SPECIFICATIONSMeasures differential, gage pressure or vacuumSuitable for air or inert gasesAccuracy ± 1% of span (including non-linearity and hysteresis)Connections 3⁄16” dia.Dimensions 3.00” W x 5.15” L x 1.40” H (76 x 131 x 36 mm)



H

Differential Pressure Transmitters for Air

Model 860 • Temperature compensated• High level output• Low power consumption• High overpressure

PLEASE SPECIFYTypeDifferential 860 or 750Gauge 860 or 750Range0/1"WC to 0/40 PSI 8600/0.1"WC to 0/5"WC 750Input Voltage24 VAC/24VDC (750 only)12-24VDC/24 VAC (860 only)Output Signal4-20mA1-5VDC1-6VDC1-10VDC (requires 24VDC/VAC input voltage)

Catalog No. Model Description PriceIX499100 860 Differential Pressure Transmitter, 1" H2O up to 1 PSI $92.00IX499101 860 Differential Pressure Transmitter, 1 PSI and above 135.00IX499200 750 0.1 to 5" H2O Transmitter 225.00ML428271 2400 Process Power Pack, 24Vdc-175mA 130.90NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

Please specify gauge type, range, input and output from above

SPECIFICATIONSMODEL 860Ranges 0 to 1" H2O through

0 to 40 PSIInput 12 to 24VDC

or 24VACOutput 4-20mA

1-5VDC1-6VDC1-10 VDC

Accuracy 1% OF FSOOverpressure 20 PSI or 2X

F.S.P., whicheveris greater

Mounting options NEMA 4x enclosureor T35 Din RailMount

Operating Temp. 0 to 60°C

SPECIFICATIONSMODEL 750 Ranges 0/0.1" H2O through

0 to 5" H2OInput 24 VDC/

24VACOutput 4-20mA

1-5VDC1-6 VDC1-10VDC

Accuracy 1% OF FSOOverpressure 15 PSI

all rangesMounting options NEMA 4x enclosure

or T35 Din RailMount

Operating Temp. 0 to 65°C

NIST it

Model 750 • ± 0.75 F.S.O. Standard accuracy

± 0.25 F.S.O. optional • Zero tracking circuitry• High overpressure• Fully temperature compensated• High level output• On board regulation• No calibration or re-calibration

required

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

792

Low Range Differential Pressure Transmitters

Catalog No. Model Description PriceVI276 276- Unidirectional differential pressure transmitter (choose range from list below) $850.00VI376 376- Unidirectional differential pressure transmitter (wet/wet) - (choose range from list below) 850.00AccessoriesNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00NISTPRQ132 — 2 Year NIST Traceable Certificate 148.00NISTPRQ133 — 2 Year NIST Traceable Certificate with Data 195.00

Viatran's "76" Series is a small size, low rangedifferential pressure transmitter that is extreme-ly accurate. Measuring 3 3/4" in height and 2 1/4"in width, this unit is one of the smallest wet/wetdifferential pressure transmitters available.

The "76" Series measures pressures from 0 to 5"WCD to 100 PSID. To accommodate vigorous testapplications, a line pressure rating of 500 PSI isstandard.

Model 276 has a 0 to 5 VDC signal, and the 376offers a 4 to 20 mA output. Viatran's capacitancesensing technology ensures long term stabilityand provides an accuracy of better than ±0.15%FSO.

SPECIFICATIONSFull Scale 0-5, 10, 20, 50, 100, 300, 750" WCDPressure Range (FSPR) 0-15, 50, 100 PSIDLinearity, Best Fit ≤0.15% FSOHysteresis & Repeatability ≤ 0.10% FSOFull Scale OutputModel 276 5 VDCModel 376 16 mAResolution InfiniteDrift ≤± 0.2% FSO per 6 monthsThermal Zero Shift ≤± 2.0% FSO per 100°FThermal Sensitivity Shift ≤± 2.0% FSO per 100°FOperating Temperature Range 0° F to + 180°FNon-Operating Temperature Range -40°F to + 250°FElectricalSupply Voltage 10 to 42 VDCPower Supply Regulation ≤± 0.10% FSO change over

supply voltage rangeOutput Signal276 0 to 5 VDC376 4-20mAZero and Span Adjustment ± 10% FSO min. ± 20% FSO max.MechanicalPressure Connection 1/4" NPT FemaleLine Pressure 500 PSIProof Pressure 500 PSIBurst Pressure 1000 PSIMaterials of ConstructionWetted Materials 316 SSTHousing 316 SST, Nickel plated zinc connectorWeight 2 lbs.

• Extremely small size• High accuracy to ≤± 0.15% FSO• All 316 stainless steel wetted surfaces• Internal field calibration circuit• Fast responseApplications• Automotive and aerospace test stands• Production test stands• Leak testing• Laboratory / Research• Shipboard / Marine

Standard Pressure Ranges When ordering please choose code that matches your specific range.Code Range Code Range Code Range Code RangeCB 0-5" WC CE 0-20" WC CN 0-100" WC AC 0-15 PSICC 0-10" WC CK 0-50" WC CU 0-750" WC AM 0-100 PSI

NIST it



H

Industrial Differential/Low Pressure Transmitter

Range "H2O Output Catalog No. Price Catalog No. Price Differential (± 0.25%) (± 0.50%) or Gauge0.10" 4-20 mA AS910501 $718.00 AS91502 $538.000.50" 1-5 VDC AS910507 658.00 AS910508 478.001.00" 4-20 mA AS910509 633.00 AS910510 453.003.00" 4-20 mA AS910513 633.00 AS910514 453.003.00" 1-5 VDC AS910515 633.00 AS910516 453.005.00" 4-20 mA AS910517 633.00 AS910518 453.0010.00" 4-20 mA AS910521 633.00 AS910522 453.0025.00" 4-20 mA AS910525 633.00 AS910526 453.0025.00" 1-5 VDC AS910527 633.00 AS910528 453.0050.00" 4-20 mA AS910529 633.00 AS910530 453.00100.00" 4-20 mA AS910533 633.00 AS910534 453.00100.00" 1-5 VDC AS910535 633.00 AS910536 453.00Standard 1⁄4" NPT female connection with screw terminal electrical connection. Optional outputs and bidirectional ranges available upon request.ML428271 2400 Process Power Pack 24Vdc-175mA 130.90NISTHP3 NIST Traceable Certificate 125.00NISTHP4 NIST Traceable Certificate with Data 159.00

The new Industrial IXLdp was designed for themeasurement and control of very low pressureand flow in industrial and process plant environ-ments. The Industrial IXLdp transmitter featuresa rugged NEMA 4X enclosure, built-in electricalterminal box isolated from the electronics andthreaded process connections.

The IXLdp transmitter utilizes a state of theart variable capacitance sensor with a glass-cladsilicon chip. The Si-Glas technology combines theinherent high sensitivity of a variable capacitancetransducer with the repeatability of a micro-ma-chined, single crystal silicon diaphragm.

The Si-Glas sensor is composed of sputteredmetals and glass molecularly bonded to silicon.There are no epoxies or other organics in the sen-sor to contribute to drift or mechanical degrada-tion over time. The silicon diaphragm withstandshigh overpressure as well as shock and vibration.

SPECIFICATIONSPerformance SpecificationsAccuracy Class (70°F Ref.)Standard ± 0.5% of F.S.Optional ± 0.25% of F.S.Accuracy: F.S. ± 0.5% ± 0.25%Non-linearityTerminal point ± 0.4 ± 0.2Best straight line ± 0.3 ± 0.15Hysteresis ± 0.02 ± 0.02Non-repeatability ± 0.05 ± 0.03Stability ± 0.5% F.S./yearStandard Ranges (Inches W.C.)Unidirectional RangesDifferential of Gage0/0.1 0/2.0 0/100/500/0.25 0/2.5 0/150/1000/0.50 0/3.0 0/200/1500/1.0 0/5.0 0/250/200Bidirectional RangesCompound or Vacuum± 0.05 ± 2.5 ± 20.0± 0.25 ± 5.0 ± 25.0± .50 ± 10.0 ± 50.0± 1.0 ± 15.0 ± 100.0Environmental CharacteristicsTemperature LimitsStorage -40 to 210°FOperating -20 to 185°FCompensated 0 to 160°FThermal Coefficients

0.5% Acc. 0.25% Acc.Zero ± 0.02% F.S./°F ± 0.01% F.S./°FSpan ± 0.02% F.S./°F ± 0.01% F.S./°FFunctional CharacteristicsOverpressure LimitsProof pressure 15 psidBurst differential pressure 50 psis

Maximum static (line) pressure100 psisMounting Position Effect1" W.C. and higher ≤0.1% F.S./g0.25" up to 0.5" W.C. ≤0.5% F.S./g0.1" W.C. ≤0.8% F.S./gWarm-up TimeFull specification 1 secondResponse TimeStandard 250msElectrical SpecificationsOutput Signal OptionsCurrent 4-20mA two wire current loopVoltage All voltage outputs are 3 wire

0-5 VDC1-5 VDC1-6 VDC± 2.5 VDC± 5 VDC

Power Supply Range12-36 VDC range without effect on outputsignalReverse Polarity ProtectedInternal Zero and Span± 10% F.S. AdjustmentSupply Current2.6mA typical for voltage outputPhysical CharacteristicsEnclosureNEMA 4X300 series stainless steelProcess Connections Two 1⁄4 NPT

femaleElectrical Two 1⁄2" female electricalConnections conduit connections

isolatedfrom the electronics.Separate access coverfor terminal connections

Media Clean, dry and noncorrosive gas

Not for Use on Liquids

• Precision Fan Tracking• Filter Monitoring• Operating Room Pressurization• Laboratory Fume Hood Control• Lab/Clean Room Pressurization• Precise Velocity Pressure

Measurement• Laminar Flow Measurement• Furnace Draft Measurement• Oven Air Flow Control• Stack Gas Flow Measurement• Baghouse Monitoring• Combustion Air/Fuel Ratio Control

• Leak DetectionHazardous LocationCertifications• FM approval is optional Factory

Mutual approvals intrinsically safefor use in:Class I, Div. 1, Groups A, B, C, DClass II, Div. 1, Groups E, F, GClass III, Div. 1, when wired inaccordance with Dresser drawings 71B241 (1-3)

• Certified 0.25% & 0.50% Accuracy• High Overload Protection• NEMA 4X Metal Construction• Six Output Signals• Easy Installation

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

794

Stainless Steel Wet to Wet Differential Pressure Transducer

Catalog No. Model Description PriceAM8210006 821TD0006BLS 0-6 psi Differential Pressure Transducer, 4-20 mA $425.00AM8210015 821TD0015BLS 0-15 psi Differential Pressure Transducer, 4-20mA 425.00AM8210100 821TD0100BLS 0-100 psi Differential Pressure Transducer, 4-20mA 425.00AM8210200 821TD0200BLS 0-200 psi Differential Pressure Transducer, 4-20mA 425.00AM8210500 821TD0500BLS 0-500 psi Differential Pressure Transducer, 4-20mA 425.00AccessoriesNISTHP3 — NIST Traceable Certificate 125.00NISTHP4 — NIST Traceable Certificate with Data 159.00NISTHPQ3 — 2 Year NIST Traceable Certificate 238.00NISTHPQ4 — 2 Year NIST Traceable Certificate with Data 238.00

SPECIFICATIONSPressure Range Up to 500 psidReference Accuracy (BFSL) ± 0.5% FS

(± 1% FS for 6 psid pressure range)Null Offset 1% FSSpan Offset 1% FS1 Year Stability < 0.25% FSOutputs 1-5 VDC 4-20mAInput Supply Voltage 8-14 VDC 12-30 VDCOperating Temperature -40 to 140°F (-40 to 60°C)Compensated Temperature 23 to 131°F (-5 to 55°C)Temperature Effects on Null ± 2% FS per 50°F (28°C)Temperature Effects on Span ± 2% FS per 50° F (28°C)Burst Pressure 5X FS from high pressure side

3X FS from low pressure sidePosition Effects Null shifts up to 0.05 psiVibration 10Gm 55-2000 Hz.Shock 30GProcess Wetted Material 316L Stainless SteelElectronics Housing Material 316 Stainless SteelProcess Connection 1/2 NPT FemaleElectrical Connection 3/4 NPT Female: 3 ft. 22 AWG cableWeight 1.8 lbs.Standard Pressure RangesPressure Code 0006 0015 0030 0060 0100 0150 0200 0300 0500Differential Pressure (PSID) 6 15 30 60 100 150 200 300 500

• All welded 316 stainless steel construction• Utilizes state of the art silicon piezoresistive sensor technology• Pressure ranges from 8 psid up to 500 psid• Outputs available in 4 to 20 mA and low power 1 to 5 VDC• Excellent accuracy and long term stability• Temperature compensated for extreme outdoor

environmental conditions• Compact size and light weight; less than 2 pounds• Designed to meet NEMA 4X outdoor weather and

corrosion resistance• Low cost

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

NIST it



H

Wet/Wet Differential Pressure Transmitter

• No moving parts towear out

• Proven long termstability ofpiezoresistive devices

• Virtually positioninsensitive

Pressure Ranges DC Model-W10 120 VAC Model-W20 DC Model-W30 120 VAC Model-W400-5 VDC output 0-5 VDC output 4-20 mA output 4-20 mA output

0-6 psid MS13152R MS23152R MS3312R MS4312R0-10 psid MS13252R MS23252R MS3322R MS4322R0-15 psid MS13352R MS23352R MS3332R MS4332R0-30 psid MS13452R MS23452R MS3342R MS4342R0-60 psid MS13552R MS23552R MS3352R MS4352R0-100 psid MS13652R MS23652R MS3362R MS4362R0-150 psid MS13752R MS23752R MS3372R MS4372R0-200 psid MS13852R MS23852R MS3382R MS4382RPrice $435.00 $445.00 $435.00 $445.00Catalog No. Model DescriptionML428271 2400 Process Power Pack 24Vdc-175mA 130.90NISTHP3 — NIST Traceable Certificate 125.00NISTHP4 — NIST Traceable Certificate with Data 159.00

The Series W pressure transmitters are de-signed to measure low differential pressures ofliquids or gases. A wide selection of standard pres-sure ranges and electrical ratings is available.

Series W transmitters are an excellent choicefor many HVAC, process and automation monitor-ing requirements. Typical applications includemeasurement of differential pressure across flowelements, heat exchangers, pumps, filters, liquidlevel monitoring and other demanding differentialpressure measurement and control applications.

The transmitters are housed in a compactheavy duty gasketed cast aluminum enclosureand are designed to IP 65 of IEC529 standardsand NEMA 4. The die cast aluminum enclosureincorporates a recessed neoprene gasket to pre-vent ingress of moisture or dust.

SPECIFICATIONSPerformanceAccuracy ±1⁄2% of differential pressure range (includes non-

linearity and hysteresis), or ± 1% for 6 psid (50 kPA) range

EnvironmentalProcess wetted surfaces are 316 stainless steelOperating temperature range 0°C to 50°C (32°F to 122°F)Shock resistance 10G (11 ms)Vibration resistance 5G, 3 to 50 HzElectrical ConnectorsPolarized Euro Plug/ConnectorsConnections Pluggable terminal block for wire 14 to 26 AWG

Mating connector is suppliedConnection to enclosure ground is provided

Connector rating 10 Amps/300 voltsMaterial Glass-filled polyesterPhysicalDimensions 3.56" x 4.54" x 2.18" (90 x 115 x 55 mm)Enclosure material Aluminum Alloy #A380Cover screws M4 Stainless Steel, non-magneticFinish Black epoxy paintPressure port connections 1/8-28 female NPTMax static pressure 100 psi up to 15 psid, 300 psi for 200 psid

INPUT/OUTPUT SPECIFICATIONSW10 3-Wire

DC Voltage InDC Voltage Out

W20 4-Wire24, 120 or 240 VAC InDC Voltage Out

W30 2-WireDC Voltage In4-20 mA Out

W40 4-Wire24, 120, 240 VAC In4-20 mA Out

ELECTRICAL SPECIFICATIONS Model W10Supply Voltage 11 to 32 Vdc (14.5 to 32 Vdc for 10 volt output).

Protected against reversal of polaritySupply current 6 mAOutput 0 to 5 Volts, linear

0 to 10 Volts, linearSink or Source 3.5 mAProtected against short circuit

Model W20Nominal Input Voltage Power Consumption Operating Voltage Range24 Vac 1.5 W 20 to 30 Vac120 Vac 1.5 W 100 to 140 Vac240 Vac 1.5 W 200 to 260 VacOutput can sink or source 3.5 mAOutput voltage is protected against short circuitTransformer isolation between power supply and output 2500 Vrms

Model W30Supply Voltage 11 to 32 VdcProtected against reversal of polarityOutput limited to approx. 3.85 mA at low end of span and a 27 mA at upper end of span

Model W40Nominal Input Voltage Power Consumption Operating Voltage Range24 Vac 1.5 W 20 to 30 Vac120 Vac 1.5 W 100 to 140 Vac240 Vac 1.5 W 200 to 260 VacIsolation between power supply and output is 2500 VrmsReceiver resistance can be from 0 to 650 OhmsOutput limited to approx. 27 mA at the upper end of span

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

796

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Wet-Wet Differential Pressure Transducers

• NEMA 4/IP65 Rating• High Accuracy• Low Cost• Fast Response• Gas and Liquid Compressors• Low Differential Ranges• No Liquid Fill Diaphragms

SPECIFICATIONSPerformance DataAccuracy ± 0.25% FS (FSS)Response Time 30 to 50 millisecondsEnvironmental DataOperating Temperature Range °F (°C) 0 to + 175 (-18 to + 80)Compensated Temperature Range °F(°C) 30 to + 150 (-1 to + 65)Zero shift %FS/100°F(%FS/50°C) 2.0 (1.8)Span Shift %FS/100°F(%FS/50°C) 2.0 (1.8)Physical DescriptionCase Stainless Steel/AluminumElectrical Connection Barrier strip terminal block with conduit

enclosure & 0.875 DIA conduit opening.Pressure Fittings 1/4”-18” NPT internalWeight (approx.) 14.4ozElectrical Data (Voltage)Circuit 3-Wire (Exc., Out, Com)Excitation 9 to 30 VDCOutput 0 to 5 VDCElectrical Data (Current)Circuit 2-WireSupply Voltage 9 to 30 VDCOutput 4 to 20mA

Applications• Process Control• Liquid Level Measurement• Refrigeration Equipment• Filter Monitoring• Compatible

Catalog No. Model Description PriceSE230100 2301001PD2F11B Differential pressure transducer, 4-20 mA output, 0-1 PSID $395.00SE230101 2301001PD2F11B Differential pressure transducer, 4-20 mA output, 0-2 PSID 395.00SE230102 2301005PD2F11B Differential pressure transducer, 4-20 mA output, 0-15 PSID 395.00SE230103 2301010PD2F11B Differential pressure transducer, 4-20 mA output, 0-10 PSID 395.00SE230104 2301025PD2F11B Differential pressure transducer, 4-20 mA output, 0-25 PSID 395.00SE230105 2301050PD2F11B Differential pressure transducer, 4-20 mA output, 0-50 PSID 395.00SE230106 2301100PD2F11B Differential pressure transducer, 4-20 mA output, 0-100 PSID 395.00SE230107 2301001PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-1 PSID 395.00SE230108 2301002PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-2 PSID 395.00SE230109 2301005PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-5 PSID 395.00SE230110 2301010PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-10 PSID 395.00SE230111 2301025PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-25 PSID 395.00SE230112 2301050PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-50 PSID 395.00SE230113 2301100PD2F2DB Differential pressure transducer, 0-5 DCV output, 0-100 PSID 395.00SE230114 2301001PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-1 PSID 620.00SE230115 2301002PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-2 PSID 620.00SE230116 2301005PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-5 PSID 620.00SE230117 2301010PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-10 PSID 620.00SE230118 2301025PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-25 PSID 620.00SE230119 2301050PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-50 PSID 620.00SE230120 2301100PD3D11B Pressure transducer with 3 valve manifold, 4-20 mA output, 0-100 PSID 620.00SE230121 2301001PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-1 PSID 620.00SE230122 2301002PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-2 PSID 620.00SE230123 2301005PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-5 PSID 620.00SE230124 2301010PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-10 PSID 620.00SE230125 2301025PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-25 PSID 620.00SE230126 2301050PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-50 PSID 620.00SE230127 2301100PD3D2DB Pressure transducer with 3 valve manifold, 0-5 VDC output, 0-100 PSID 620.00Accessories


The Model 230 is a high level output, low differential pressure transducer de-signed for wet to wet differential pressure measurements of liquids or gases. A fast-response capacitance sensor and signal conditioned electronic circuitry provide ahighly accurate, linear analog output proportional to pressure. Both unidirectionaland bidirectional pressure ranges are available for applications with line pressure upto 250 psig. All parts exposed to the pressure media are stainless steel and elastomerseals. The 230 has a NEMA 4/IP65 rated package to withstand environmental effects.

The model 230 can be supplied with an optional 3-valve manifold assembly forease of installation and assembly. The 3-valve manifold is a machined brass body re-quiring no internal pipe connections, thereby eliminating the risk of internal leaks.The manifold’s rugged, yet compact, construction requires minimum space for instal-lation and use. The 230 bleed ports allow for total elimination of air in the line andpressure cavities. If the Model 230 is ordered with the 3-valve manifold, the system isshipped completely assembled and ready for a wall or piping mounting.



H

SPECIFICATIONSAccuracy of Reading Standard, ± 1% of span + 1 digitSetpoint Accuracy ± 0.2% of span + 1 digit (including repeatability)Power Requirements 105—135 VAC, 50/60 Hz or

210—265 VAC, 50/60 HzPower Consumption 2.5 VAElectrical Connections Non-interchangeable power and alarm plugs

with #4-40 screw clamps; wire range is 14—22 AWG

Alarm Outputs 1-spdt 0.5A@120 VAC- electromechanical relayDimensions 1⁄8 DIN 1.89" H x 3.78" W x 5.71" D

Dual Alarm/Controller with 2 relays (1 rising pressure, 1 falling pressure)

Catalog No. Pressure Range PriceMS191131 0-0.1˝ H2O $425.00

MS1911311 0-0.5˝ H2O 425.00

MS1911312 0-1˝ H2O 425.00

MS1911313 0-5˝ H2O 425.00

MS1911314 0-10˝ H2O 425.00

MS1911315 0-30˝ H2O 425.00

MS1911316 0-50˝ H2O 425.00

MS1911317 0-3 PSID 425.00

MS1911318 0-5 PSID 425.00

MS1911319 0-15 PSID 425.00

MS1911310 0-50 PSID 425.00

Accessories



RANGE CHART — PRESSUREPressure Resolution

Range Capacitance cell0 to 0.1" H20 0.001"0 to 0.5" H20 0.001"0 to 1.0" H20 0.01"0 to 5.0" H20 0.01"0 to 10.0" H20 0.01"

Silicon sensor0 to 30.0" 0.1"0 to 50.0" 0.1"0 to 3 psid 0.01"PSID0 to 5 psid 0.01"PSID0 to 15 psid 0.01"PSID0 to 50 psid 0.1"PSID

Low Differential Pressure Alarm/ControllerThe Model DA is a controller for the monitoring

of low differential pressures. It combines in oneenclosure a low pressure transducer, a digital dis-play and up to two alarms. It is typically used forthe monitoring of clean room pressures, duct stat-

ic and velocity pressures, as well as filter differ-ential, draft, fume hood and other low pres-

sure applications.The pressure sensing element is adifferential capacitance cell for pres-

sure measurements ranging from0.1 to 10.0 inches of water (25 Pato 2.5 kPa), or a piezoresistive(silicon) sensor for pressures from10 inches of water to 30 psi (2.5kPa to 200 kPa).

The display section has 31⁄2 dig-its with bright, easy to readLED's. The display is factory-cali-brated to read in engineeringunits.

The alarm section is offeredwith 1 or 2 alarms.

Barb fittings ( 3⁄16" O.D.) and pluggable termi-nals with screw clamps are provided at the rearfor quick and simple field connections.

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

798

SPECIFICATIONSGeneralPressure Connections Barbed 1⁄8" (3mm) I.D. tubingMedia Compatibility Air and non-corrosive gasesElectrical Connections Terminal blockHousing Gray PVC type IWeight 8.5 ounces (241 grams)Adjustments Accessible potentiometersDimensions Cutout: 1.775" x 3.625" 4.5" depthElectricalPower Supply 10 - 35 VDC -2, 3 or 4 wire

16 -26 VAC -4 wireOutput Signal 4-20 mA DC (limited at 38 mA DC)Loop Resistance 0 - 1300 ohms DC max

0 - 1200 ohms AC maxPerformance at 70°F (21.1°C)Zero Output 4 mA DCFull Span Output 16 mA DCAccuracy ± 0.5% of full span output (Includes linearity,

hysteresis and repeatability)Span and Zero Adjustable to 0.05% of full spanWarm-up Time 10 minutesEnvironmentalOperating Temperature 20 to 120°F (-6.7 to 49°C)Thermal Errors ± 0.02%/°F typicalMetric ranges available upon request.

Catalog No. Model Description Range Max. Pressure PriceDW600 621-3 Pressure Indicator 0-3 in. w.c. 5 psi $239.00DW601 621-6 Pressure Indicator 0-6 in. w.c. 5 psi 239.00DW602 621-10 Pressure Indicator 0-10 in. w.c. 5 psi 239.00DW603 621-20 Pressure Indicator 0-20 in. w.c. 11 psi 239.00DW604 621-40 Pressure Indicator 0-40 in. w.c. 11 psi 239.00DW605 621-100 Pressure Indicator 0-100 in. w.c. 29 psi 239.00DW606 621-200 Pressure Indicator 0-200 in. w.c. 29 psi 239.00DW607 621-1000 Pressure Indicator 0-1000 in. w.c. 150 psi 239.00DW608 621P-10 Pressure Indicator 0-10 psi 58 psi 239.00DW609 621P-20 Pressure Indicator 0-20 psi 58 psi 239.00DW610 621P-30 Pressure Indicator 0-30 psi 58 psi 239.00DW611 621P-50 Pressure Indicator 0-50 psi 150 psi 239.00DW612 621P-100 Pressure Indicator 0-100 psi 150 psi 239.00



1⁄8 DIN Housing, 4-20 mA OutputMeasure and control compatible air or gas pres-

sure and converts it into a 31⁄2 digit display with a4-20 mA output signal. Positive, negative or dif-ferential pressures can be measured with a fullspan accuracy of ±0.5%. Ranges are available from0-3 in. w.c. (0-0.75 kPa) to 0-100 PSI (0-690 kPa).Versatile circuit design enables use in 2, 3 or 4-wire current loops.

Air/Gas Pressure Indicator with Transmitter OutputDifferential, Positive or Negative Pressure

NIST it



H

NEMA 4 Pressure Switches

General Purpose Pressure Switches

• Wide selection of adjustable ranges• Internal reference scales and

adjustment lock• Enclosure design permits safe and

easy access for wiring• Many models available from stock• Choice of 1⁄2" NPT electrical connection

or knockouts• Internal reference scale• Adjustment lock for tamper-resistance• 1 piece low copper aluminum

enclosure and sensor body

Pressure Model Chart Type H100

316 stainless steel diaphragm and 1⁄2" NPTF pressure connection

Catalog Model Stock Numbers Adjustable Range Deadband Proof PriceNo. for Type H100 PSI Bar Lower 75% Top 25% Pressure

range span range spanVC148 190 95303 5-30 psi 0.34-2.07 1-3 6 max 2500 psi $122.00VC149 191 95310 10-100 psi 0.69-6.90 1-8 15 max 2500 psi 122.00VC150 192 95317 15-300 psi 1.03-20.69 3-18 25 max 2500 psi 122.00VC151 193 95324 20-500 psi 1.38-34.48 4-30 45 max 2500 psi 122.00VC152 194 95331 80-1700 psi 5.52-117 5-120 150 max 2500 psi 122.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

Pressure Model Chart Type J40

Phosphor bronze bellows and 1⁄4" NPTF brass pressure connection

Catalog Model Stock Numbers Adjustable Range Deadband Proof PriceNo. for Type J40 PSI Bar PressureVC153 218 9634 30"Hg VAC to 0 PSI -1.02-0 1.0-2.5" Hg VAC 30"Hg VAC $57.00VC154 222 9591 0-20 psi 0-1.38 0.2-1.3 psi 30 psi 55.00VC156 226 9608 0-50 psi 0-3.45 0.2-1.3 psi 75 psi 54.00VC157 230 9624 0-100 psi 0-6.90 1.0-2.3 psi 110 psi 55.00NISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00

SPECIFICATIONSApprovals UL recognized component.

Optional CSA certification.Set Point Repeatability ± 1% of adjustable rangeSwitch Output (1) SPDT. Switch may be

wired “normally open” or “normally closed”

Electrical Rating 15 amp 125/250 VAC resistive

Weight Approx. 2 lb.Pressure Connection Models 190-194: 1⁄2" NPTF

NIST it

NIST it

• Low cost, small size and light weight for OEM applications• Wide selection of adjustable ranges within 30" Hg VAC to100 PSI

• Bellows sensors for ± 1% repeatability• One 15 amp switch output

Save 50%on 2nd year

recalibration

Ask about2 YearNIST


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

800

• Corrosion resistant enclosure meets NEMA 3, 4, 4X, 13 and IP66• Choice of switch elements for all applications, including hermetically sealed• Wide choice of wetted materials, including all-welded Monel or stainless steel• Fixed or limited adjustable deadband• Approved for UL, CSA and FM ratings• Choice of actuators, including designs for fire-safe and NACE applications• Standard pressure connection materials

Pressure psi ranges -316 SS Differential psid ranges-Nickel-plated brass Pressure and differential inches of water ranges-Carbon steel

Pressure/Differential Switch

SPECIFICATIONSDescription / Maximum Electrical RatingsUL/CSA listed SPDTGeneral purpose 15A, 125/250/480 Vac

1/2A, 125 Vdc1/4A, 250 Vdc

Please inquire for additional switches including dual switch modelsActuator SealCode & Process RangeMaterial Temp.

Limits °FVac 0-600 1000 2000- H2O psi psi 3000 psi

B-Buna N 0 to 150° • • • • StandardV-Viton® 20 to 300° • • • Available upon

requestT-Teflon® 0 to 150° • • • • Available upon

requestS-St.St. 0 to 300° • • StandardP-Monel 0 to 300° • • Available upon

request

Diaphragm &O-Ring

Catalog No. Model Material Description Range PriceAS775800 B400 Buna N Pressure Switch 30" Hg Vac $153.00AS775802 B400 Buna N Pressure Switch 30" Hg Vac/30 psi 153.00AS775803 B400 Buna N Pressure Switch 30" Hg Vac/60 psi 153.00AS775806 B400 Buna N Pressure Switch 10" H2O 163.00AS775807 B400 Buna N Pressure Switch 60" H2O 163.00AS775809 B400 Buna N Pressure Switch 15 psi 133.00AS775810 B400 Buna N Pressure Switch 60 psi 133.00AS775811 B400 Buna N Pressure Switch 100 psi 133.00AS775812 B400 Buna N Pressure Switch 200 psi 133.00AS775813 B400 Buna N Pressure Switch 600 psi 133.00AS775826 B400 Stainless Steel Pressure Switch 60 psi 178.00AS775827 B400 Stainless Steel Pressure Switch 100 psi 178.00AS775829 B400 Stainless Steel Pressure Switch 600 psi 178.00AS775830 B400 Stainless Steel Pressure Switch 1000 psi 223.00AS775831 B400 Buna N Pressure Switch 3000 psi 193.00AS775832 D400 Buna N Differential Pressure 30" H2O 283.00

SwitchAS775834 D400 Buna N Differential Pressure 100" H2O 283.00

SwitchAS775835 D400 Buna N Differential Pressure 150" H2O 283.00

SwitchAS775838 D400 Buna N Differential Pressure 100 psid 318.00

SwitchAS775839 D400 Buna N Differential Pressure 400 psid 325.00

SwitchNISTPR132 — NIST Traceable Certificate 99.00NISTPR133 — NIST Traceable Certificate with Data 130.00Stainless Steel, Differential Switches are available upon request. Upon request Viton®, Teflon® and Monelmaterials are available for diaphragms and o-rings

Watertight Enclosure Meets NEMA 3, 4, 4X and 13 Requirements

This general purposeAshcroft® switch series is idealfor use in virtually all Industrialand OEM applications.

NIST it

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

N-Series Electronic Pressure Switch

• Thin film pressure sensor (transducer) • Diaphragm – 17-4 PH SS• Pressure Connection – AISI 316 SS• Watertight meets NEMA 3, 4, 4X, 13 and IP66. Optional enclosure for

NEMA 7, 9, Division I or II Hazardous locations• Pressure settings to 20,000 psi.• Status Light – Indicate Display Function

-Process Pressure-Setpoint-Resetpoint-Relay Output Status

• Big and bright 3 1⁄2 digit LED display indicates process pressure ± 1%• 3⁄4 NPT electrical connection for easy wiring• Multi-turn potentiometers make setpoint and deadband adjustment easy• 10 AMP SPDT relay contacts for maximum flexibility in electrical

output needs

ORDERING INFORMATION N-SERIES PRESSURE SWITCH MODEL NUMBER:To specify the exact switch desired select entries from appropriate tables as shown in example below

N P A N 4 D L S 0 1 X E A 60 PSI

1 2 3 4 5 6 7

1 – FUNCTION

NPA – Single setpoint, adjustable deadband $375.00

NPI – Single setpoint, adjustable deadband, $475.00process and setpoint indication

4 – POWER REQUIREMENT

L – 110 Vac, 50/60Hz N/C

C – 24 Vdc N/C

V – 250 Vac, 50/60 Hz $50.002 – ENCLOSURE

N4 – Watertight NEMA 3, 4, 4X, 13 and IP66 N/C

N7 – Explosion proof NEMA 3, 4, 4X 13, 7, 9 & $140.00IP66 – Not available with Model NPI (display)

7 – NOMINAL RANGEPERFORMANCE TABLE (psi)

Nominal Setpoint psi psiRange Limits Proof Burst

60 3-60 120 480 N/C100 5-100 200 800 N/C200 10-200 400 1600 N/C300 15-300 600 2400 N/C500 25-500 1000 4000 N/C750 35-750 1500 6000 N/C1000 50-1000 2000 8000 N/C2000 100-2000 4000 16,000 N/C3000 150-3000 4500 20,000 N/C5000 250-5000 7500 22,500 N/C7500 375-7500 9000 25,000 N/C

10,000 500-10,000 12,000 30,000 N/C15,000 750-15,000 18,000 45,000 N/C20,000 1000-20,000 24,000 60,000 N/C

For reliability in the toughest applications!

Pressure sensor is a stable thin film trans-ducer. The signal processed produces an outputto an electro-mechanical relay, rated for10,000,000 cycles at rated load. Narrow dead-bands can be adjusted to less than 0.5% ofrange, solving many pipeline and elevated tankapplications that are beyond the reach of me-chanical products. The indicating model is ideally suited for appli-cations where both pressure indication and aswitch output for alarm, shutdown, control orinterlock are needed.

3 – OUTPUT

D – SPDT Relay 10A, 250 Vac N/C

10A, 30 Vdc

5 – PRESSURE PORT

S01 – 1⁄8 NPT Male N/C

S02 – 1⁄4 NPT Male N/C

S03 – 1⁄8 NPT Female N/C

S04 – 1⁄4 NPT Female N/C

S05 – 7⁄16-20 SAE - 1⁄4 SAE N/C

S06 – 1⁄2 NPT Male 1⁄4 & NPT Female N/C

S07 – 1⁄4 AMINCO – Female N/C

6 – OPTIONS

XEA – External adjustment (N4 only) 25.00


NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

802

Bürkert "All-In-One" Pressure Transmitter/Switch

Please inquire for pricing and ordering information.

SPECIFICATIONSProcess SpecificationsPipe Diameter Any pipe with 1/2" FNPT connection - TypeSO01 or SO05Measuring Range 0-29, 73, 145, 290, 725 PSISwitching Accuracy ± 1.5% full scaleRepeatability Max. 0.25... 1% full scaleFitting Type SO01 or SO05Housing Material PC + 20% glass fiberFront Panel Foil PolyesterSensor Element Ceramic cell (AI2, O2)Wetted Parts Stainless SteelMin. Service Life 100 million cyclesof Pressure CellElectrical SpecificationsVoltage Supply 12-30 VDCReversed Polarity of DC ProtectedTransistor Output NPN/PNP, open collector 5-30 VDC, 700 mAor optional Relay Output 3 A, 230 VAC, or 3 A, 30 VDC programmableInput External Setpoint 4-20 mAOutput Process Value 4-20 mAOptional AS-Interface FieldbusCurrent Consumption Max. 80 mA (no load)Short Circuit Protection YesRecommended Max. Cable 328 ft. shieldedLength for Power Supply 26 to 22 AWGEnvironmental SpecificationsMax. Fluid Temperature 212°FAmbient Temperature Range -4°F to 140°FType of Protection NEMA 4 (IP65) with connector plugged in

• All In One - Indication, Controller, Transmitter, ON/OFF Relay and AS-iControl in One Device

• Programmable Monitoring and ON/OFF control system for easy fluid controlsystems

• Complete communication due to external setpoint, easy link or AS-interface• ON/OFF Control

- Stabilized pressure of N2 in liquid tanks- Control of pressure tanks for air- Control if fluid pressure tanks

• Monitoring- Monitoring of fluid in low pressure in Reverse Osmosissystems (water treatment)

- Monitoring of pressure in autoclaves

This Transmitter/Switch is specificallydesigned to switch a valve, pump, heaters,etc... and to establish and ON/OFF controlloop. The switching point can be pro-grammed with the 3 keys on the display orfrom an external logic controller via a 4-20mA loop. Additionally, the process valuecan be transmitted to the PLC (4-20 mA).The connection to the process in the pipingis done with standard fittings.



H

The Pressure Logger records pressure from 0 to100 PSI, 0 to 300 PSI or 0 to 500, it has aWaterproof Stainless Steel case and a 5 year bat-tery. Its compact size, smaller than a hockey puck,is perfect for tight locations and outdoor applica-tions. Eliminate changing chart paper and pens.View data in real time or download data when youneed it.

User friendly software makes it simple to inte-grate recorded pressure data into documents andspreadsheets, giving results a professional, pol-ished look. When fulfillment of regulatory require-ments or accurate recording of pressure for quali-ty control is needed, the PR100, PR300 and PR500are the perfect instruments!

Pressure Logger

SPECIFICATIONSPressure Ranges PR100, 0 - 100 PSI; PR300, 0 - 300 PSI; PR500, 0 to 500 PSIAccuracy ± 1% full scaleAmbient Operating Conditions 32 to + 122F (0 to + 50°C); 0 - 100% RHApprovals CEBattery Type Lithium 3.6V, user replaceableBattery Life 5 year typical @ 1 minute sample intervalsFitting 1/4" NPT Thread, 5/8" HexSample Point Storage 7936 pointsSample Interval User Selectable from 10 sec. to 24 hours in 10 sec. incrementsDownload Time 45 secondsResolution 0.1 PSIResponse Time 10 seconds typicalEnclosure 316 Stainless SteelDimensions 1.064" x 1.975" DIA (2.70cm x 5.02cm DIA)Weight 4.0 ozSoftware & Download Cable SpecificationsCompatible with: Windows™ 95,98,2000 & NTPC Requirements: PC w/386 or better microprocessor, 4M RAM, 1 free COM (serial) port, CD driveCable Type/Length: 9 pin male D-shell to male 2.5mm stereo plug, 6' longComputer Interface: RS-232 COM (serial) portVersion Required (minimum): 6.0.4.2

PR100/PR300/PR500

Catalog No. Model Description PriceDK976518 PR100 0 to 100 PSI Pressure Logger $399.00DK976519 PR300 0 to 300 PSI Pressure Logger 399.00DK976531 PR500 0 to 500 PSI Pressure Logger 499.00DK015 A015 Software and Download Cable 69.00AccessoriesDK1164117 A791 Pressure Fitting Accessory Kit 89.00DK976527 A793 Fire Hydrant Adapter Kit 150.00DK116323 R022 Filter Kit 25.00DK976528 A792 Steam Pressure Pigtail 30.00DK976529 A717 Locking Case 45.00NISTDL01 — NIST Traceable Certificate 200.00NISTDL02 — NIST Traceable Certificate with Data 250.00NISTDLQ01 — 2 Year NIST Traceable Certificate 300.00NISTDLQ02 — 2 Year NIST Traceable Certificate with Data 375.00

NIST it


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

804

These Pressure Recorders with remote sensorsemploys advanced microcontroller design that en-ables this versatile instrument to accurately mea-sure and record pressures. Selector switches locat-ed on the face panel allow for the recording of 3 different pressure range at 4 different recording speeds.

Pressure Recorders

• Advanced microcontrollerdesign

• Large LED digital display showssensor pressure

• Front panel selectable — Allcontrols are located on frontpanel for fast and easy setup

• Remote pressure sensor has a6' long cord with a stainlesssteel 17-4 pressure port 1⁄4 NPT,burst pressure 2500PSI ratedfor any gas or fluid compatiblewith 17-4 stainless steel

• Standard adapter for 120 VACoperation (220 VAC optional)

• Battery backup assures normaloperation during power interruptions

• Furnished complete with 2 car-tridge pens & 60 (6" diameter)assorted charts

• Free standing or wall mounted• Weather proof NEMA type 4X

(CSA type 4) case optional• 6" Diameter Chart• Single or continuous chart

rotation• 3 pressure ranges• 4 recording speeds• 12 VAC operation — Allows use

in vehicular or marine operations

• Snap-on extra support legs

SPECIFICATIONSPressure range 0 to 500 PSI, 0 to 150 PSIPSI Model 0 to 50 PSIPressure range 0 to 35 BAR, 0 to 10 BARBAR Model 0 to 3.5 BARAmbient operating temperature range + 32°F to + 140°F

(0°C to + 60°C)Ambient operating relative humidity 96% maximumChart speed selectable — 6 hours,

24 hours, 7 days, 31 daysChart rotation mode Selectable — single turn or

continuousChart speed accuracy +/- 1%Chart diameter 6 inchesPressure accuracy +/- 1% F.S.Display 3 digit LED 0.5"Power Supply 120 VAC, 50/60 Hz.

(220-240 VAC, 50/60Hz.optional - CR87PB)

Battery life 48 hours continuous useBattery backup 8 AA Alkaline batteries

(not included)Case size 9 1⁄4" x 7 1⁄4" x 2 3⁄4"Weight 4 lbs., 7 oz.

NIST it

Catalog No. Model Description PriceSUCR87P CR87P PSI Pressure Recorder, $375.00

110-120 V, 50/60 HzSUCR87B CR87PB BAR Pressure Recorder, 375.00

220-240 V, 50/60 Hz.NISTRC1 — NIST Traceable Certificate 125.00NISTRC2 — NIST Traceable Certificate 199.00

with DataPensSC7741711 — Chart Recorder Pen (Black) 7.73SC774172 — Chart Recorder Pen (Red) 7.73SC774173 — Chart Recorder Pen (Blue) 7.73Charts Pressure 6 Hrs. 24 Hrs. 7 Days 31 DaysRange0 - 500 PSI 6H500PSI 24H500PSI 7D500PSI 31D500PSI 18.000 - 150 PSI 6H150PSI 24H150PSI 7D150PSI 31D150PSI 18.000 - 50 PSI 6H50PSI 24H50PSI 7D50PSI 31D50PSI 18.00

Save 50%on 2nd year

recalibration

Ask about2 YearNIST



H

Weather Resistant Pressure RecordersThe PW4 weather resistant pressure recorder is housed in a fiberglass NEMA

4X case. This lightweight 4" recorder will provide protection against corrosion,windblown dust and rain, splashing water and hose directed water.

These pressure recorders are not suitable for monitoring ammonia, acids, saltwater or other corrosive substances. The PW 461 and PW 462 are suitable for monitoring salt water.

8" Pressure Recorders NIST it

NIST it

Applications• Pressure studies and tests on gas

and water lines• Monitor line pressure on

production lines• Field verification of customer com-

plaints• Monitor steam pressure in plant

Place these portable Pressure Recorders anywhere you want a written recordof pressure. You don’t even need to be present to monitor the results. Pleasekeep in mind that pressure recorders are not suitable for monitoring ammonia,acids, salt water or other corrosive substances.

Catalog Chart Recording Recorder Replacement 60 Charts No. Model Size Range Time Price Chart No. Price

DK1164108 PR8100PB7S 8" 0 to 100PSI 7-day $499.00 C412 $18.00DK1164109 PR8100PB24S 8" 0 to 100PSI 24-hour 499.00 C410 18.00DK1164112 PR8200PB7S 8" 0 to 200PSI 7-day 499.00 C436 18.00DK1164113 PR8200PB24S 8" 0 to 200PSI 24-hour 499.00 C456 18.00Catalog No. Model Description

DK1164117 A791 Accessory Kit (washers, fittings & adapters) 89.00DK116212 P222 Six-pack standard red pens 30.00NISTRC1 — NIST Traceable Certificate 125.00NISTRC2 — NIST Traceable Certificate with Data 159.00

SPECIFICATIONSAccuracy ±2% full scaleAmbient Operating -22 to +122°F Temperature (-30 to +50°C)Average Response 1 secondTimeCase Fiberglass NEMA 4X with door

window (weather resistant, waterresistant)

Chart Size 4" diameterConnection 1⁄4 " male NPTPower Supply One "AA" alkaline batteryWeight 1.8 lbs.Dimensions 6.25" x 6.0" x 2.9"Includes One "AA" alkaline battery, Pen,

One box of 60 charts

Catalog Pressure Recording Chart Price Catalog Pressure Recording Chart PriceNo. Model Range Time No. No. Model Range Time No.DK1164101 PW451 0-100PSI 24hr. C010 $379.00 DK1164110 PW450 0-100PSI 7 day C012 $379.00DK1164103 PW453 0-150PSI 24hr. C025 379.00 DK1164111 PW452 0-150PSI 7 day C035 379.00DK1164105 PW455 0-200PSI 24hr. C026 379.00 DK1164104 PW454 0-200PSI 7 day C040 379.00DK1164106 PW457 0-300PSI 24hr. C022 379.00 DK1164114 PW456 0-300PSI 7 day C036 379.00DK1164107 PW459 0-500PSI 24hr. C028 379.00 DK1164115 PW458 0-500PSI 7day C056 379.00— N/A N/A N/A N/A N/A DK1164118 PW460 (FM Approved) 0-300PSI 7 day C036 379.00— N/A N/A N/A N/A N/A DK1164119 PW461 (SS Sensor/FM Approved) 0-300PSI 7 day CO36 529.00— N/A N/A N/A N/A N/A DK1164120 PW462 (SS Sensor/FM Approved) 0-600PSI 7 day CO43 529.00AccessoriesCatalog No. Model DescriptionDK1164117 A791 Accessory Kit 89.00DK116323 R022 Filter Kit 25.00DK116324 A793 Fire Hydrant Adapter Kit 150.00See Chart No. Above — Box of 60 replacement charts 18.00DK116212 P222 Replacement Pen Pack (6 red) 30.00NISTRC1 — NIST Traceable Certificate 125.00NISTRC2 — NIST Traceable Certificate with Data 159.00

SPECIFICATIONSAccuracy ± 2% full scaleMount 1⁄4 " male NPT connection, nickel plated brassAmbient Operating -22 to + 122°F (-30 to + 50°C)TemperatureResponse Times 1 to 5 secondsPower Battery operated quartz chart movement (AA)Includes One box of 60 charts, pen and

instruction manual


H

Pres

sure

/ Pr

essu

re C

alib

rato

rs

806

• A pressure cylinder for storage of 2200 PSI (The cylinder has a gaugeattached for a constant display of reserve available pressure. The stor-age cylinder can be refilled via a quick disconnect port by using anynormal cylinder regulation system)

• A precise regulator for generating an approximate pressure setting• A precision volume controller attached to the output of the regulator for

"fine tuning" the pressure• A vent in the system for venting the pressure to atmosphere• Two ports on the system (one port to attach to any pressure standard

calibrator, the other for item under test)• Durable rugged case• Light weight - approx. 28 lbs. (13" x 13" x 15")

Pressure Generation & Controlling Systems

Catalog No. Model Description PriceJM100101 PGS Pressure Generation System $3,950.00JM100102 PCS Pressure Controlling System 2,950.00

Provides All-In-One ConveniencePressure Generation SystemMeter can be used to generate precise pressureswith gas from atmosphere to 2000 PSI also precisegeneration of low pressures for various calibrationranges.

The system can also be used to generate verylow pressures by using the volume adjuster as apressure generator. The volume adjuster will gen-erate approximately 10 - 15 PSI by itself with.0005 PSI resolution. Excellent for "H2O low pres-sure calibration". The regulator has fine enoughadjustment to aid in low pressure generation aswell.

• Pressure resolution control in tenths in PSI and hundredths in "H2O"• A precise regulator for generating an approximate pressure setting• A precise volume adjuster attached to the output of the regulator for

"fine tuning" the pressure• A vent in the system for venting the pressure to atmosphere• Two ports on the system (one port to attach to a pressure standard,

the other for item under test)• Durable rugged case• Light weight - approx. 13 lbs. (6" x 10" x 12")

NIST it

Pressure Controlling SystemTo be used with an air cylinder or plant air.

Great for controlling and maintaining pressure.



H

Vacuum Generator/Pressure Controller

Ideal for hazardous areas whereconventional vacuum pumps darenot tread

This unique pressure/vacuum controllerprovides up to 29 inches Hg vacuum in areasthat are off limits to vacuum pumps. The allmechanical design allows the operator to useexisting shop air lines working with a built invacuum converter inside the unit. Shop air issimply connected to the rear of the light-weight unit and the operator selects vacuumor pressure mode of operation. The built inpressure regulator also allows the operator towork with the shop at lower pressure levels ifdesired.

SPECIFICATIONSPressure Media Filtered Shop AirPressure Input 120-150 psi, 4.2 S.C.F.M.,

AN-4 37° Flared Tube FittingPressure Limit Monitor Gage Size: 2" diameter, Range: 0-160 psiVacuum Monitor Gage Size: 2" diameter

Range: 0-30" HgRegulator All Aluminum DesignCase SteelPressure/Vacuum Selector BrassFittings Brass, Quick Disconnect, 1⁄4"Internal Tubing 250 psi rated tubingSize/Weight 5.6" x 8.1" x 6" HWD/6.6 lbs.

• All mechanical design• No fumes• No vibration• Lightweight design• Controls and regulates positive pressure

Catalog No. Model Description PriceEA111418 UVC1000 Vacuum Generator/ $795.00

Pressure Controller

Provides 29 Inches Hg Vacuum from your Shop Air Supply!

Save 50%on 2nd year

recalibration

Ask about2 YearNIST

Economical Digital Pressure Gauge NIST

Documents