Drip Pro - Spray Nozzle Engineeringsprayingsolutions.com.au/.../uploads/2013/10/HI-FLO-DRIP-PRO_ds.pdfDrip Pro® Hi-Flo GEN-3 . spray dry nozzle check valve by . Spray Nozzle Engineering.

from the company with over two decades of dryer nozzle experience in the field

Hi-Flo GEN-3ANOTHER GIANT LEAP FORWARD IN

SPRAY DRY DRIP CONTROL

Drip Pro

REDUCE SCORCHED PARTICLES WITH LONGER RUN TIMES*

The Drip Pro Hi-Flo GEN-3 Check Valve in conjunction with BETE Thick Swirl technology, is a NEW heavy duty design

that will not only continue to reduce the drips which contribute to scorched particles, but is able to

run in the most demanding environments for longer time periods.

* when compared with earlier valve generations

Latest Generation Anti-Drip Valve for BETE Twist&Dry Spray Dry Nozzle Systems

Drip Pro G EN-3 helps keep you running longer

www.spraynozzle.com.au

With Drip Pro Hi-Flo GEN-3 valve technology, improved product quality is only part of the story. NEW check valve improves flow, reduced pressure loss and dramatically

reduces blockages delivering longer dryer run times*.

A smarter approach towards control of drips & scorched particles

Drip Pro Hi-Flo GEN-3

BETE Twist&Dry carrier (cap) Refer to BETE data for cap & pressure options.

BETE Twist&Dry sealing options standard & optional high pressure series with back-up ring provision. Refer BETE data for pressure & seal options.

Integrated new Drip Pro Hi-Flo GEN-3 Check Valve with replaceable seal not only allows a number of sealing options but its new high flow design runs longer than previous designs and is easily removed for cleaning.

Unique patented removable seal guide keeps seals concentric for reliable seating & sealing whilst allowing the use of low cost sacrificial seal inserts which increase valve body seat life.

Trusted BETE thick swirl and orifice combinations deliver expected spray performance and powder quality through traditional industry standard swirl/orifice metering geometry. Refer to BETE data for metering combinations & performance.

Thread galling resistant stainless steel standard on all Drip Pro Hi-Flo GEN-3 nozzles. Helping combat seized carriers (caps).

Unique patented high flow spring cage with bayonet action keeps valve parts contained in nozzle body during swirl and disc changes along with keeping valve components concentric for reliable action. No more springs jumping out on disassembly with Drip Pro!

from the company with over two decades of experience to the food and processing industry World Wide.

Low cost replaceable soft seal is available in a range of materials and ensures improved sealing without damage to the nozzle body seat. Avoiding seat damage prevents expensive replacement of nozzle bodies, particularly when welded.

Various spring options allows optimized spring pressure and seal combinations for longer seal life and reliable shut off.

* when compared with earlier valve generations

spraynozzle.com.au

With Drip Pro Hi-Flo GEN-3 valve technology, improved product quality is only part of the story. NEW check valve improves flow, reduced pressure loss and dramatically

reduces blockages delivering longer dryer run times*.

Severe scorched product due to seal leakage. The beginning of a potential dryer fire. Old worn nozzles cause this failure. Replace old nozzles.

Leakage due to seal & gland damage. Gland surface damage may have pinched & torn O-ring at assembly. It is critical to regularly look for nozzle damage & replace damaged components immediately. Care of your nozzles is crucial.

Poor Nozzle Condition is a Safety Issue... That's why its never a better time than NOW to upgrade to Drip Pro Hi-Flo GEN-3. Keeping your valves in tip-top condition is critical to safe operation. If you are using older valves then it is a great opportunity to upgrade to Drip Pro Hi-Flo GEN-3 and in doing so replacing any old or worn parts to reduce the risks of dryer fire. It's time to look closely at your nozzles.

GEN-1small lug(Fully superseded)

GEN-3Latest VersionSuperior high flow, long run performance

STEM91003-1

STANDARD SEAL OPTIONS*

DURACON 91005-1 PTFE 91005-2

STANDARD BODY SPRING

91006-1**

NEW Hi-Flo VALVE BODY 91009-1

NEW Hi-Flo CAGE

91001-3

for Swirl, Orifice, Carrier, Seal & Pressure options see BETE TD Catalogue* contact factory for other materials** contact factory for other spring options

Gen-2big lug (Valve body & springcage superseded)

SNE-SS-SL-CVBOD1.4-LT

SNE-SS-CV-CAGE-BL

Drip Pro a little history, a big advance The Drip Pro story began almost 10 years ago with a call from one of the world's largest spray dryer OEMs. They had a problem with nozzle drips during commissioning of a new plant which resulted in scorched particle deposits at the fluid bed, compromising the quality of the milk powder. The challenge they posed was to develop an anti-drip check valve which would function reliability in the difficult service conditions of the milk fluid path. We soon discovered that many had tried and failed in developing a reliable valve for spray dry nozzles, however with our detailed knowledge of these service problems, we set to work on a new valve design which would satisfy these difficult conditions. The result was our unique Drip Pro patented design which proved such a success that the OEM set about converting many existing plants in our region with this first generation valve (GEN-1). The resultant end user feed back regarding product quality improvements, set the stage for the evolution of what has become the industries best performing anti-drip spray dry valve.

Drip Pro Hi-Flo GEN-3, the evolution continuesIf your already using Drip Pro check valves you'll know the quality advantages achieved over no valves at all. But did you know the valve design has continually improved over the last 10 years. This could mean your existing valves may not only be up to 10 years old, worn and potentially a dryer fire risk, but are likely to have been superseded by new improved models.

Our first valve was the Drip Pro GEN-1 valve which was accepted as one of the first spray dryer valves in the industry to deliver reliable operation over a full shift run without blockages. Age alone dictates full replacement of this early version.

The new Drip Pro Hi-Flo GEN-3 was created to meet the higher productivity demands of the spray dry industry today, not only to meet the demand for higher flow rates, but to also meet the requirements of longer run times. The increased flow was achieved with changing two low cost interchangeable internal components allowing the user to keep the same body as previously used so Upgrading to the new Drip Pro Hi-Flo GEN-3 is easy!

Never used a Spray Dry Check Valve Before? The advantages of using a Drip Pro Hi-Flo GEN-3 spray dry nozzle check valve by Spray Nozzle Engineering will improve

product quality, reducing the amount of scorched particles in your dryer. Ask us how to upgrade your dryer to Drip Pro Hi-Flo GEN-3 today!

What condition are your nozzles in?

Can lead to Can lead toOld, superseded, damaged nozzles that look like this...

STANDARD FLOW INTERNAL TO BE SUPERSEDED The Drip Pro GEN-2 valve introduced improvements in

component durability with an expanded range of spring pressures & seal materials. This was achieved with larger body/ cage lugs & threads, allowing the Drip Pro GEN-2 far greater longevity than its predecessor. Inspect body for wear & damage, replace as required & upgrade to GEN-3 internals.

SPRA

Y DR

Y AC

CESS

ORIE

S

www.spraynozzle.com.au

MELBOURNE, AUSTRALIA 1-8/27 Shearson Crescent, Mentone, Vic. 3194

P +61 (0)3 9583 2368 F +61 (0)3 9585 0218 E sales@spraynozzle.com.au

Other Accessories

Euro: Pat. grant, Aust. Pat. No: 2010201737, NZ Pat. No: 532132, USA : Pat. Pend. Warranty: The manufacturer will replace, repair or refund the purchase price of The Product at their option, free of charges, except transportation, if defective in their manufacture. Claims must be notified to the manufacturer in writing within 90 days of sale or shipment either of which occurs first. The Product should be returned to the place of purchase. This warranty is ex-clusive remedy and the Manufacturer/Distributor shall not be liable for consequential damages, injury or commercial loss. The Manufacturer/Distributor makes no warranty of fitness for a par-ticular purpose and makes no other warranty, express or implied arising from the course of dealing or usage in trade. Specification subject to change without notice. Chemical, Temperature and pressure compatibility is the responsibility of purchaser, compatibility charts available at request. Spray Nozzle Engineering Pty Ltd Australia / New Zealand APR12

A.SNE-SS-STORK-CIP-CAP B.SNE-SS-QC-CAP-DRIPPRO

A.SNE-SS-SL-CVSTM-TOOL B.TD-CAP-SPANNER

O-RING HOOK-PICK 7825

One easy tool for all O-ring removal and replacement operations.

Laminated work area use guide sets contact Spray Nozzle Engineering for details.

NEW ZEALAND / PACIFIC RIM 532c Grey Street, Hamilton East, NZ 3216

P +64 (0)7 839 6444 F +64 (0)7 839 6445 E sales@spraynozzle.co.nz

NOTICE! YOUR NOZZLE PARTS ARE PRECISION HIGH PRESSURE COMPONENTS. THEIR CARE & MAINTENANCE IS CRITICAL TO SAFE & PROPER OPERATION!

Care of your Drip Pro equipment will help deliver significant reductions in damage, increase safety and assist in trouble free operation. The following accessories will be a great addition to the care of your Drip Pro check valve and Twist&Dry nozzles.

NOTICE! MIXING AND INTERCHANGE OF NON-ORIGINAL PARTS WITH Drip Pro STANDARD COMPONENTS IS DANGEROUS & WILL VOID WARRANTY

Easy to use tools made specifically for the job, to prevent unnecessary damage caused by incorrect tool use.

CIP Caps for both hose and rocket

launcher type wash systems.

CLEANING BASKET 92001-1TD SOFT BOARD 92001-1SB

Handling InstructionsALWAYS study

Handling Instructions

sales@spraynozzle.com.au

A.

A.B.

B.

A soft "push" with tool is all

that is required

SOFT PUSH ORIFICE REMOVAL TOOLSNE-CD-SOFT-TOOL

Soft Handling BASKET =Soft Handling BOARDALWAYS use

Soft Handling BOARDALWAYS use

Soft Handling BASKET

ORIFICE GAUGE - SNE-130-IMPOrifice diameter measuring should be part of your pre-run quality checking. Now this can be easily done with Spray Nozzle Engineering orifice gauge. Other sizes available.