Dishwasher Installation instructions instructions d ...

YOURLIFE.OURINSPRATJON.

Dishwasher Installation instructions

instructions d'instaHation du _ave-vaisse_e

Instrucciones de insta_aci6n para _avavajiHas

Use and Care Manua_ _ocated on reverse side

Tourner _e guide pour _ee instructions d'utHisation et d'entretienVo_tee e_ manua_ para encontrar _as instruccionee de uso y cuidado

9000089901 (8506)

Tabmeof Contents / _mportant Instructions

important Safety instructions

To avoid possible injury or property damage,OBSERVE ALLWARNmNGS AND CAUTmONS.These instructions are intended for use byqualified installers onty.

The dishwasher must be installed by a qualifiedserqce technician,, in addition to these instructions, the dishwasher

shah be installed to meet all electrical andplumbing codes and ordinances (both national andlocal),

Read these installation instructions completelyand follow them carefully. They will save you timeand effort and help to ensure safety and optimum

If the dishwasher is installed ina location thatexperiences freezing temperatures (e.g., inahoJiday home), you must drain aH the waterfrom the dishwasher's interior.Water systemruptures that occur as a result of freezing arenot covered by warranty.

IMPORTANT* The dishwasherdrain hose must be installed

with a portion of it at least 20" (508mm) off thecabinet floor; otherwise the dishwasher may notdrain properly,

* This dishwasher is intended for residential use

only, and should not be used in commercial foodservice establishments,

* NEW INSTALLATION - If the dishwasher is anew installation, most of the work must be donebefore the dishwasher is moved into place,

* REPLACEMENT - If the dishwasher is replacinganother dishwasher, check the existingdishwasher connections for compatibility withthe new dishwasher, and replace parts asnecessary,

* This appliance has been found to be incompliance with CAN/CSA-C22,2 No, 167/UL749, It is the responsibility of the owner and theinstaller to determine if additional requirementsand standards apply in specific installations,

Inspect the DishwasherAfter unpacking the dishwasher and prior toinstallation, thoroughly inspect the dishwasher forpossible freight or cosmetic damage, Report anydamage immediately, Cosmetic defects must bereported within 30 days of installation,NOTE: Do not discard any bags or items that comewith the original package until after the entireinstallation has been completed,

Tooms and Matedams Needed

TOOLS NEEDED

Hammer

\

Hob Saw

Tape Measure Sbt Screwd river PhHHpsScrewdriver %20 Screwdriver

Wire Cutter Wire Stripper DrHU LeveU

MATERIALS NEEDED(AdditionaU materiab may be required to compUywith UocaUcodes,)

EbctrbaU SuppUyCabb ° Minimum #14 AWG, 2 conductor, 1 ground, insuUated copperconductors rated 75°C or higher,

Hot Water Supply Line - Minimum 3/8" O,D, copper tubing or metal braided dishwashersupply line,

Shut-off valve and fittings appropriate for hot water supply line (copper tubing/compression fitting, or braided hose),

90° elbow with 3/8" N,RT, male threads on one leg, and sized to fit your water supplyline (copper tubing/compression fitting, or braided hose) on the other leg,

Teflon tape or other pipe thread compound to seal plumbing connections,

UL listed conduit connector or strain relief,

2

Materials Supplied

MATEFImALS SUPPUEDAccessory Parts SuppliedAccessory parts for your dishwasher come in one or more pUastb bags that are outlined bebw,NOTE: Make sure you save aH the bags until you have compbted your installation,NOTE: AUwaysuse the supplied or recommended hardware,

f Manual Set BagA ManuaUSet Bag is provided with each dishwasher andincUudes:

A Use & Care instructions and installationinstructions (both manuab may be indudedin a singb "fHp-styb" book

B Quick Reference Guide (select models)C ExtraTall Item Sprinkler ',,D SHI and SHV Installation Template (SHI and SHV "-

models only)8 s,$E White Cotton Insulation Strip (SHY66C, SHX99A,

SHE66C, SHE99C and SHX57C models only)

A Dishwasher Installation Kit is provided with eachdishwasher and includes:

F Toe Panel Screws (2 black machine screws)Note: These screws are included, but not used onmodels with the Toe Panel Installation Kit,

G CounterTop Mounting Brackets (2 %?shaped metalbrackets)

H Mounting Bracket Screws (2 silver wood screws)m Rubber Drain Hose Adaptor (1 black rubber tube)J Hose Clamps ( 1 silver spring clamp to use to

attach the rubber adaptor to the Drain Hose and 1gold screw clamp to attach the rubber adaptor to

K Wire Nuts (3 for electrical connection)L Electrical Junction Box Screws (2 silver

machine screws)IV] Leg Leveler Locking Screws (2 gold coarse

f SHm/SHV Door PaneJ mnstaHation Kit

A Door Panel Installation Kit is provided with selectdishwashers that use a custom wood door panel andincludes:

N Plastic Caps (2) _' _0 Spring Tension Screws (2 larger silver machine

screws used to adjust the door springs to accom-modate doors of different weights)

P Door Mounting Brackets (2 gold metal bracketsand 2 white plastic brackets used to mount thecustom door)

Q Door Mounting Bracket Screws (8 silver woodscrews) _ ®@ _@

R Door Mounting Screws (2 long silver screws used _ _ ........._..............t_ a!t_£_tht_tO r).......................................................................................................................................................................................................................................

f Toe PaneJ installation Kit _'AToe Panel Installation Kit is provided on modelsSHY66C, SHX99A, SHE66C, SHE99C and SHX57C,These models have a special noise reducing Toe Panelwith the following mounting hardware:

S Toe Panel Screws (2 black screws used to attach _

T Black Plastic Base Access Panel Screws (2 longsilver screws used to attach the Black plastic

3

f Dishwasher Installation Kit

Enclosure Preparation

23 9/16"',598mm)

23-5/8" - 24-1/4" (600-616 mm

Figure 1

Check _ ......... -EE EEclearance E

betweendishwasher ,

Idoor and wall

Countertop

Figure 2

i\

I\\I

\

Electrical Shock Hazard

To avoid electrical shock, make sure the watersuppJy and ebctrical suppJy are shut off beforeinstallation or service.

ENCLOSURE PREPARATmON

NOTE: This dishwasher is designed to be enclosed on thetop and both sides by standard residential kitchencabinetry.

Select a location as close to the sink as possible foreasy access to water supply and drain lines.For proper dishwasher operation and appearance, ensurethat the enclosure is square and has the dimensionsshown in Figure !.If the dishwasher is to be installed in a corner, make surethat there is adequate clearance to open the door. SeeFigure 2,

ElectricaJ Shock/Fire Hazard

To avoid ebctric shock or fire, do not allow theeJectricaJ and water supply Jines to touch.Separate channets are provided under thedishwasher (see page 10}.

if the enclosure requires openings for the electrical supplycable, hot water supply line, and dishwasher drain hose,place them within the dimensions shown by the shadedarea of Figure 3 to avoid interference with the dishwasherframe or other components, Make the openings for theelectrical supply cable and hot water supply line 1"(25,4mm) diameter, Make the opening for the dishwasherdrain hose 1-1/4" (82mm) diameter, if the openings aremade through wood, sand them smooth, if the openingsare made through metal, make them large enough toaccommodate grommets or other protective sheaths withinside diameters of 1" (25,4mm) for the electrical supplycable and the hot water supply line, and 1-1/4" (32mm) forthe dishwasher drain hose,

Figure 3

4

Emectrica{Preparation

ELECTRICAL PREPARATmON

30 _'

(762mm)

2! EE

(533mm)

ElectdcaJ Shock Hazard

To avoid electrica! shock, do not work on anenergized circuit. Doing so could resuJt in seriousinjury or death. OnJy quaJified eJectricians shouJdperform etectricaJ work. Do not attempt any workon the dishwasher eJectric suppJy circuit until youare certain the circuit is

de-energized.

Figure 4

Dishwasher Electrical Rating

Vemts Amperes Watts

120 60 15 1,450(max)

(76mm- 102mm)

3/8"- 1/2" _ .<(10mm - 13mm)< J

Figure 5

Fire Hazard

To avoid a fire hazard, make sure eJectdcaJ workis properJy installed. OnJy qualified eJectriciansshouJd perform eJectrical work.

ElectricaJ SuppJyThe customer has the responsibility of ensuring that thedishwasher electrical installation is in compliance with allnational and local electrical codes and ordinances. Thedishwasher is designed for an electrical supply of 120V,60 Hz, AC, connected to a dishwasher-dedicated,properly grounded electrical circuit with a fuse or breakerrated for 15 amps. Electrical supply conductors shall be aminimum #14 AWG copper wire rated at 75°C or higher.

Regardless of where the electrical supply cable enters theenclosure, position the cable 21" (533mm) from theenclosure's left side, as shown in Figure 4. Extend thecable 30" (762mm) from the enclosure's back, as shownin Figure 4,

Remove 3" =4" (76mm =102mm) of the cable's outercasing, as shown in Figure 5, then remove 3/8" - 1/2"(10 - 13mm) of insulation from each wire, as shown inFigure 5,

!4"(356mm)

Hot WaterSupply

Line

Figure 6

Plumbing Preparation

PLUMBING PREPARATmON

ScaJd HazardTo avoid being ecaJded, do not perform any workon a charged hot water line. Serious injury couJdreeuJt. Only quaJified plumbers ehouJd performptumbing work. Do not attempt any work on thedishwasher hot water supply pJumbing until youare certain the hot water euppJy is shut off.

Temperatures required for soldering and sweatingwill damage the dishwasher's base and water intetvalve. If plumbing lines are to be soldered orsweated, keep the heat source at least 5 inches(152.4 ram) away from the dishwasher's base andwater inJet vaJve.

Hot Water SuppJyThe hot water heater should be set to deliverapproximately 120 ° F (49° C) water to the dishwasher,Water that is too hot can cause some detergents to loseeffectiveness, Lower water temperatures will increase runtimes, The hot water supply pressure must be between15 - 145 psi (1 - 10 bar),

Hot Water SuppJy PJumbingInstall an easily accessible shut-off valve (not supplied) inthe hot water supply line, as shown in Figure 5, All solderconnections must be made before the water line isconnected to the dishwasher's water inlet valve, Watermay abe be supplied to the dishwasher by using astainless steel braided hose approved for dishwasher use,Check with your local plumbing supply sources for theproper hose and 90° elbow fitting,

NOTE: Regardless of where the hot water supply lineenters the enclosure, position the line 14" (356mm) fromthe enclosure's left side, as shown in Figure 6,

NOTE: Decide whether stainless steel braided hoseapproved for dishwasher use or copper tubing will be usedfor the hot water supply plumbing, and purchase thecorrect type of hot water supply shut-off valve, 90° elbow,and necessary fittings for the hot water supply plumbing,

6

YobranchTailpiece

Pmumbing Preparation/Dishwasher Preparation

Figure 8

g J

Figure 9

Step 2

Figure 10

Step I

Figure 11

_E

PLUMBING PREPARATmON (continued}Drain PJumbingUnder Sink Drain Connectionif the dishwasher is to drain either directUyinto thehousehoUd drain pUumbingor through an air gap, install ay-branch taHpbce under the sink as shown in Figure 7,

Installing an Air Gapff bcaUordinances require an air gap, as shown inFigure 8, install it according to the manufacturer'sinstructions,

DisposerMake sure to remove the disposer's dishwasher drainconnection plug before connecting the dishwasher drainhose, See Figure 9,

DISHWASHER PREPARATmONDishwasher preparation involves four tasks:• Installing the Mounting Brackets

Removing the Toe PanelInstalling the 90° elbow fittingJunction Box Preparation

Installing the Countertop Mounting Brackets

Before installing the supplied countertop mountingbrackets, decide which method of securing thedishwasher into its enclosure wilt be used. Oncethe mounting brackets are installed on the dish-washer, removing them is difficult and will damagethe mounting brackets and the dishwasher.

The dishwasher can be secured into its enclosure in two

ways:1 Top Mount is used for countertops made of wood or

other materials that can easily drilled, Orient themounting brackets as shown in Figure 10, andposition the two small tabs on the mounting bracketsover the two slots on the dishwasher's front corners,Push the mounting brackets down firmly to insert thetabs into the slots,

2 Side Mount is used for countertops made of marble,granite, or other very hard materials that cannot beeasily drilled, Bend the mounting brackets along thesmall hobs and in the same direction as the two smalltabs, Orient the mounting brackets as shown in Figure11, and position the two small tabs on the mountingbrackets over the two slots on the dishwasher's frontcorners, Push the mounting brackets down firmly toinsert the tabs into the slots,

Tip Over HazardTo avoid a tip over hazard, do not use thedishwasher until it is completeJy installed. Whenopening the door on an uninstaHed dishwasher,carefully open the door while supporting the rearof the unit. Failure to follow this warning canresult in serious injury.

Toe

PaneU

Figure12

J

Figure 13

Dishwasher Preparation

DISHWASHER PREPARATmON (continued}

When any covers are removed or the dishwasheris out of the cabinet, eJectdcal power and sharpedges or points may be exposed.

Removing theToe Pane1Regular Toe PanelThe toe paneUis UooseUyattached with tape, Remove thetape and pull the toe paneUaway from the dishwasher, Setthe toe paneUaside, UtwHUbe reinstalled Uater,

Plastic Base Access PaneJ and Toe PaneJ (SHY660,SHX99A, SHE660, SHE990 and SHX570 modeJe only)The plastic base access panel and toe panel are in placeon the dishwasher, but are not attached, Remove the toepanel first, as shown in Figure 12, then remove theplastic base access panel, as shown in Figure 12,

Do not overtighten the 90° elbow. Doing so maydamage the water intet vaJve and cause a waterteak.

installing the 90 ° Elbow FittingNOTE: The 90° elbow fitting is not supplied with thedishwasher, and must be purchased separately, If thedishwasher's hot water supply line is to be copper tubing,make certain the elbow has a compression fitting,ApplyTefion tape or other pipe sealant when required,Orient the hot water supply connection leg of the elbowtoward the channel opening in the dishwasher base, SeeFigure 13,

Junction Box Preparation1 Remove junction box cover (see Figure 14) by lifting

the junction box cover up and off,2 Remove the strain relief plate by removing the screw

at the back of the junction box, as shown in Figure15 and sliding the strain relief plate out,

3 Set the junction box cover, strain relief plate, andscrew aside, They will be re°installed later,

Figure 14 Figure 15

8

Door Panem_nstaHation

DOOR PANEL mNSTALLATmON

Figure 16

SH U/SH E ModeJs - Accessory Pane1 installationHfyou have an SHU/SHE modeHand have ordered anaccessory paneHkit, instaHHthe paneHprior to sliding thedishwasher into pHace.The paneHdimensions are shown inFigure 16.

SHi Modets - Pane! installationSHHmodeHscome with additionaHmounting hardware anda tempHatesheet with instaHHationinstructions. The stain-HesssteeHmodeHs of the SHHseries arise come with twoextension pieces. The extension pieces are used tomatch the controHpaneHheight (Figure 17, "B" dimension)to the horizontaH drawer Hineof the cabinets, and must beinstaHHedas shown in on the tempHate sheet. The standardpiece is used for drawer heights up to 6" (152mm); theHongpiece is used for drawer heights greater than 6"(152mm) but 6o7/16" (164mm) or Hess.Hfyour drawers aretaHHerthan 6o7/16", you can either sHidethe extensionpiece in as far as it wiHHgo, or remove it and fit the doorpaneHdirectHybellow the controHpaneH.

C

A

Figure 17

SHI/SHV Models - Panet installationSHV modeHscome with additionaH mounting hardware anda tempHatesheet that wiHHshow you how to mount thepaneH.One side of the tempHate shows how to mount aone piece paneH;the other side shows how to mount a twopiece paneH.Decide which type of instaHHationyou wantbefore proceeding with the instaHHation.

Fig. 17Dimension

SHI Only

Fig, 18 Panem DimensionDimension

20 11/16" - 25"D (SHI) (526mm - 635mm)

E 27 3/!6" - 30 5/!6"(SHI & SHV) (690ram - 770ram)

F 23 3/16" - 23 3/8"(SHI & SHV) (589mm - 594mm)

Extension "A"

Max. - Mino "B .... C"

Standard Long Maxo-Min,

5/16- 11/16" i11/16- 1 1/8" 55/16" 55/8-67/16"

(8-18mm) i(18 - 29mm) (!35mm) (143 - 164mm)

Figure 18

Pmacing the Dishwasher/Securing the Dishwasher

PLACmNG THE DISHWASHER

1 Straighten and position the hot water supply line andthe electrical supply cable as shown in Figure 19 sothat they wiii align with their channels under thedishwasher base.

2 Position the dishwasherclose enough to the enclosureso that you can run the dishwasher drain hose to theunder sink drain connection. Make certain that the hot

water supply line and the electrical supply cable are intheir channels under the dishwasher base, as shown inFigure 20,

3 Slide the dishwsher into the opening making sure thatthe hot water supply line and the electrical supplycable stay in their proper channels.

4 Make sure the dishwasher is level. Adjust the rearleveler by turning the center screw at the front of thedishwasher, as shown in Figure 21a. Turning the screwclockwise raises the rear of the dishwasher. Adjust thefront levelers by turning them with a screwdriver, asshown in Figure 21b. Turning the levelers to the rightraises the dishwasher, if additional height is needed,shims may be added under the leveler feet.

Channels

Figure 20

SECURING THE DISHWASHER

1 Drive the mounting screws through the hobs in themounting brackets as shown in Figure 22 for Top orSide Mount.

Figure 21

/Top Mount

10

• ScrewBoss

Figure 23

Drain Hose Connection

2 After the unit is installed in the enciosure, ieveled andsecured, Hockthe two front ieg ievelers in piace bydriving the enciosed ieg ieveler Hockingscrews intoeach screw boss iocated in front of the ievelers, SeeFigure 23,

3 Tighten screws until they are flush with the surface ofthe bosses,

mnstaHation of the Rubber Drain Hose

Adaptor1 Obtain the Rubber Drain Hose Adaptor and the two

hose champs from the Dishwasher installation Kit,2 On one outside end of the Rubber Drain Hose Adapter

is a raised rib, insert the drain hose into the endwithout the raised rib. Be sure to fully insert the drainhose,

3 Secure the connection with the Silver Spring Clamp,4 Use the Gold Screw Clamp to attach the Rubber Drain

Hose Adaptor to the house plumbing,

Figure 24 Figure 25

Connecting the Drain Hose to the

Household P_umbingThe dishwasher drain hose may be connected to the drainpiumbing in one of four ways:1 Directiy to the undersink dishwasher drain connection,

as shown in Figure 24.2 Directiy to a disposer dishwasher drain connection, as

shown in Figure 25.3 To the undersink dishwasher drain connection through

an air gap, as shown in Figure 26.4 To a disposer dishwasher drain connection through an

air gap, as shown on Figure 27.

information on installing air gaps and disposers can befound in the Ptumbing Preparation section of thismanual,

NOTE: if the dishwasher drain hose is to be connected toa disposer dishwasher drain connection, remove the plugfrom the disposer's dishwasher drain connection,Use the supplied Rubber Drain Hose Adaptor and DrainHose Clamps to connect the dishwasher drain hose to theplumbing drain connection, Use the spring clamp tosecure the Rubber Drain Hose Adaptor to the dishwasherdrain hose, Use the screw clamp to secure the RubberDrain Hose Adaptor to the plumbing drain connection,

The dishwasher drain hose must have one place along itslength that is securely attached 20 inches above thecabinet floor,

Figure 26 Figure 27

11

Hot Water Connection

HOT WAFER CONNECTmON

ScaJd HazardTo avoid being scalded, do not perform any workon a charged hot water tine. Serious injury couJdresult. Only quaJified pJumbere should performplumbing work. Do not attempt any work on thedishwasher hot water supply p_umbing until youare certain the hot water euppty is shut off.

NOTE: Make certain that the correct 90° elbow fitting (notsupplied) for the hot water supply line has been pur-chased and installed on the dishwasher as described inthe Dishwasher Preparation section of this manual,The hot water supply line may be connected to thedishwasher in one of two ways:1 With braided hose,2 With copper tubing,

Stainless Steet Braided Hose Approved for Dish-washer Use.After connections are made turn on the hot water supplyto check for leaks,NOTE: Braided dishwasher supply hoses can also beused to extend pre-existing dishwasher water supplylines,

CopperTubing

Temperatures required for soldering and sweatingwitt damage the dishwasher's water inJet valve, ifplumbing lines are to be eotdered or sweated,keep the heat source at Jeaet 6 inches (152.4 ram)away from the dishwasher's water intet vaJve.

, if using a solder joint instead of a compression fitting,be sure to make all solder connections before

connecting the water line to the dishwasher,* Make certain there are no sharp bends or kinks in the

water line that might restrict water flow,* Be sure to use pipe thread compound or Teflon tape to

seal the connection when required,, Before connecting the copper hot water supply line to

the dishwasher, flush it with hot water to clear anyforeign material,

* Turn on the water supply to check for leaks after

NOTE: Do not use pipe sealant on compression fittings,

12

StrainReliefPJate

(not sui

Figure 28

Figure 29

Casing

EmectdcalConnection

ELECTRICAL CONNECTmON

EJectrical Shock HazardTo avoid electrical shock, do not work on anenergized circuit. Doing so could result in seriousinjury or death. OnJy quatified electricians shouJdperform electrical work. Do not attempt any workon the dishwasher electric supply circuit until youare certain the circuit is de-energized.

Fire Hazard

To avoid a fire hazard, make sure eiectrica! workis properly installed. Only qualified eJectriciansshouJd perform eJectricaJ work.

Grounding instructionsThe dishwasher must be properly grounded beforeoperating, This appliance must be connected to agrounded metal permanent wiring system, or anequipment grounding conductor must be run with thecircuit conductors and connected to the equipmentgrounding terminal or lead on the dishwasher, Make surethat the dishwasher is connected to a suitable ground incompliance with all local codes or, in the absence of alocal code, with the NATIONAL ELECTRICAL CODE inthe United States orthe CANADIAN ELECTRIC CODEC22,1 -latest edition in Canada as well as any provincial/state or municipal or local codes that apply,

1 Retrieve the strain relief plate, and install a strain relief(not supplied) into the opening on the strain relief plate,NOTE: Orient the strain relief as shown in Figure 28,

2 Pass the electrical supply cable through the strainrelief, as shown in Figure 29, Make sure the outer wirecasing extends about 1/2" (18mm) through the strainrelief,

3 Tighten the strain relief screws,4 Slide the strain relief plate into the junction box, and

secure it to the junction box with the supplied screw,

13

ElectricamConnection/Door Tension Adjustment/Base and Toe Panem

._ ELECTRICAL CONNECTmON (continued)

Figure 31

Figure 32J

Fire Hazard

To avoid a fire hazard, make sure there are notoose eJectricaJ connections. Make sure aH

etectricaJ connections are properly made.

o Do not pre-twist the wires before connecting themwith wire nuts,

o Extend the dishwasher's stranded wires 1/8" (3mm)beyond the power supply cable's solid wires, asshown in Figure 30,

5 Using the supplied wire nuts, connect the electricalsupply wires to the dishwasher's wires, black to black,white to white, and green or bare, Make certain thatthe insulated wires show no bare wire from the

bottoms of the wire nuts, Gently tug the wires to makecertain they are securely connected,

6 Press the wires into the junction box as shown inFigure 31, Make certain that the wire nuts do notloosen,

7 Place the cover on the junction box and secure it tothe junction box with the supplied screw,

DOOR TENSION ADJUSTMENT (orfly on SHIand SHV mode_s with custom door pane_s)After the dishwasher and custom door panel are installed,open and close the door several times to make sure thatit does so with ease, If the door falls open too quickly,the spring tension needs to be adjusted,

To Adjust the Spring Tension:1 Obtain the provided Spring Tension Screws from the

SHI/SHV Door Panel Installation Kit,

2 insert the screws as shown in Figure 32, Turning thescrew clockwise increases the spring tension,

TOE PANEL mNSTALLATmON

RegularToe Panel installationUse the toe panel screws from the Dishwasher Installa-tion Kit and a %20 screwdriver to install the toe panel asshown in Figure 33,

14Figure 33

Base and Toe Panem/Final Instructions

BASE AND TOE PANEL (Continued)

PJastic Base Access Panel and'Foe Pane! installation(SHY66C, SH×99A, SHE66C, SHE99C, SH×57C, andSHV57C models onJy)1 PUacethe PUastb Base Access PaneUunder and up the

front bottom paneUof the dishwasher, as shown inFigure 34a,

2 insert the PUastb Base Access PaneUscrews into thePUastb Base Access Panel as shown in Figure 34b,Tighten the PUastb Base Access PaneUScrews,

3 PUace the Cotton UnsuUationStrip under the unit,between the bottom of the PUastb Base Access PaneUand the floor, as shown in Figure 34c,

4 Attach the Toe PaneUto the PUasticBase Access Panelusing the Toe Panel Screws included in the Toe PanelInstallation Kit, See Figure 34d,

NOTE: You will not use the normal Toe Panel Screwsincluded in the Dishwasher Installation Kit on thesemodels,

in some conditions, Hydrogen gas can form in ahot water system that has not been used forweeks. Hydrogen gas is e×pJosive. Before fillinga dishwasher from a system that has been off forweeks, run the water from a nearby faucet in awett ventilated area untit there is no sound or

evidence of gas.

FINAL mNSTRUCTmONS

1 Energize the dishwasher power supply circuit,2 Consult the Dishwasher Use and Care Manual, and run

the dishwasher through one complete cycle, If thedishwasher does not operate properly, refer to the SelfoHelp section of the Use and Care Manual, If thedishwasher still does not operate properly, refer to theCustomer Service Section of the Use and CareManual,

15

Customer Service

CUSTOMER SERVICE

Your Bosch dishwasher requires no speciaUcare other than that described in the Care and CUeaningsection of the Useand Care Manual Ufyou are having a proMem with your dishwasher, before calling for service pUeaserefer to the Serf-HeUpsection of the Use and Care Manual Ufservice is necessary, contact your deaUeror installer or an authorizedservice center, Do not attempt to repair the appliance yourself. Any work performed by unauthorized personnel mayvoid the warranty,

Removing any cover or pulling the dishwasher from the cabinet can expose hot water connections, electrical power and

If you are having a problem with your Bosch dishwasher and are not pleased with the service you have received, pleasetake the following steps (in the order listed below) until the problem is corrected to your satisfaction,

1, Contact your installer or the Bosch Authorized Service Contractor in your area,

2, E-mail us from the customer service section of our website, www, boschappliances,com,

3, Write us at:

BSH Home Appliances, Corp,

5551 McFadden Avenue

Huntington Beach, CA 92649

4, Call us at 1-800-944-2904,

Please be sure to include (if you are writing), or have available (if you are calling), the following information:

* Model number

oSerial number

* Date of original purchase

oDate the problem originated

* Explanation of the problem

Also, if you are writing, please include a daytime phone number where you can be reached, You will find the model andserial number information on the label located on the right-hand side of the inner door of your dishwasher, see Figure 1,It will look similiar to this:

r_

i

Please make a copy of your invoice and keep it with this manual, The customer must show proof of purchase to obtainwarranty service,

16© BSH Home Appliances Corporation 2005 _ Litho U.S.A. 07/04

©BSHHomeAppliancesCorporation2005,,LithoU,S,A,07/049000089901(8506)