CX-LDB10/LDB20diagramas.diagramasde.com/audio/CX-LDB10.pdf · 2012. 5. 1. · Sony Corporation Personal Audio Group Published by Sony Engineering Corporation AEP Model E Model CX-LDB10/LDB20
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SERVICE MANUAL
Sony CorporationPersonal Audio GroupPublished by Sony Engineering Corporation
FM tuner sectionTuning range 87.5 – 108.0 MHzAntenna FM lead antennaAntenna terminals 75 ohms unbalancedIntermediate frequency 10.7 MHz
AM tuner sectionPan-American model: 530 – 1,710 kHz
(with the tuning interval set at 10 kHz)531 – 1,710 kHz (with the tuning interval set at 9 kHz)
European model: 531 – 1,602 kHz (with the tuning interval set at 9 kHz)
Other models: 530 – 1,710 kHz (with the tuning interval set at 10 kHz)531 – 1,602 kHz (with the tuning interval set at 9 kHz)
Antenna AM loop antenna, external antenna terminal
Intermediate frequency 450 kHz
Photo : CX-LDB20
2
CX-LDB10/LDB20
Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 °C
during repairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiationexposure.
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 °C.Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
This appliance is classified as a CLASS 1 LASER product. This label is located on the rear exterior.
GeneralPower requirementsEuropean model: AC 230 V, 50/60 HzKorean model: AC 220 V, 60 HzAustralian model: AC 230 – 240 V, 50/60 HzMexican model: AC 120 V, 60 HzArgentine model: AC 220 V, 50/60 HzOther models: AC 110 – 120 V or
220 – 240 V, 50/60 HzAdjustable with voltage selector
Power consumptionCX-LDB20: 95 W
0.3 W (in Power Saving Mode)
CX-LDB10: 65 W0.3 W (in Power Saving Mode)
Dimensions (w/h/d) excl. speakersApprox. 160 × 230 × 255 mm
Mass excl. speakersCX-LDB20: Approx. 4.0 kgCX-LDB10: Approx. 3.8 kg
Design and specifications are subject to change without notice.
9. ELECTRICAL PARTS LIST .................................. 40
4
CX-LDB10/LDB20SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATIONCHECKCarry out the “S curve check” in “CD section adjustment” and checkthat the S curve waveforms is output three times.
MODEL IDENTIFICATION– Back Panel –
Model Name Power Voltage Indication
Mexican model 120 V AC, 60 Hz
AEP, Russian models 230 V AC, 50/60 Hz
Korean model 220 V AC, 50/60 Hz
Australian model 230 – 240 V AC, 50/60 Hz
Other models110 – 120 V or
(E51, Singapore, Malaysia and220 – 240 V AC, 50/60Hz
Argentine models)
Power voltage indication
5
CX-LDB10/LDB20SECTION 2GENERAL This section is extracted
from instruction manual.
Main unit
AUDIO IN 8 (16, 22)AUDIO IN jack qg (18, 22)BASS/TREBLE q; (17)Cassette compartment qjCD SYNC wa (16)DISPLAY 9 (14, 20)Display window 5FOLDER +/– qk (10, 11, 16)
4 two vibration proof rubbers (GRN)5 base unit (BU-K7BD81B)
3 two vibration proof rubbers (PNK)
2 two screws(+PSW2.6 × 10)
9
CX-LDB10/LDB20
3-5. MECHANICAL DECK (CMAL5Z220A)
3-6. CONTROL BOARD
2 four screws(BVTP3 × 8)
3 coating clip
4 two earth wires
1 wire (flat type) (7core)
5 plate (shield cassette)
6 mechanical deck (CMAL5Z220A)
8 CONTROL board
2 three screws(BVTP2.6 × 8)
3 seven screws(BVTP2.6 × 8)
1 knob (VOL)
4 wire (flat type) (17core) (CN401)
5 wire (flat type) (23core) (CN403)
6 wire (flat type) (7core) (CN404)
7 wire (flat type) (11core) (CN402)
10
CX-LDB10/LDB20
3-7. MAIN BOARD, POWER TRANSFORMER
3-8. LID (CASSETTE)
2 screw(BVTP3 × 8)
3 two sumitite screws(B3)
5 two tapping screws (B3)
9 four screws
7 two claws
8 holder (pwb PT)
6 shield cover
4 MAIN board
1 connector (13P)(CN902)
q; power transformer
1 Open the lid cassette.
3 lid cassette
claw
two hooks
2
2
11
CX-LDB10/LDB20SECTION 4TEST MODE
COLD RESET• The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode whenreturning the set to the customers.
Procedure:1. Press the ?/1 button to turn the set ON.2. Press three buttons x , ?/1 and [VOLUME] down simulta-
neously.3. The message “RESET” is displayed and the set is reset.
TUNER STEP CHANGE• A step of AM channels can be changed over between 9 kHz
and 10 kHz.Procedure:
1. Press the ?/1 button to turn the set ON.2. Select the function “TUNER”, and press [TUNER/BAND]
button to select the BAND “AM”.3. Press the ?/1 button to turn the set OFF.4. Press the > and ?/1 buttons simultaneously, and thus
the channel step is changed over.
SHIP RESETProcedure:
1. Press the ?/1 button to turn the set ON.2. Press the CD u button to select “CD”3. Remove the disc.4. The message “NO DISC” is displayed.5. Press three buttons x , CD u and [VOLUME] down si-
multaneously.6. The message “SHIP RESET” is displayed and the set is reset.
The CD function is activated.7. To exit from this mode, press the ?/1 button and pull out the
AC plug.
PANEL TEST MODE• This mode is used to check the software version, LCD, LED
and keyboard.Procedure:
1. Press the ?/1 button to turn the set ON.2. Press the CD u button to select “CD”3. Press three bottons [DISPLAY] , ?/1 and [VOLUME] down
simultaneously.4. When the panel test mode is activated, all segments are turned
on.
VERSION DISPLAY• This mode is used check the model, destination, software
version.Procedure:
1. When the panel test mode is activated, press the button[BASS/TREBLE], the model and destination are displayed.
KEY TEST MODEProcedure:
1. When the panel test mode is activated, press the H button,to select the key test mode.
2. To enter the KEY test mode, the fluorescent indicator displays“K0 VO”. Each time a button is pressed, “KEY” valueincreases. However, once a button is pressed, it is no longertaken into account. When all keys are pressed correctly, “K15VO” is displayed.
3. To exit from this mode, pull out the AC plug.
CD Repeat 5 Times Limit Release ModeProcedure:
1. Press the ?/1 button to turn the set ON.2. Set the function to “CD”.3. Press three buttons x , H , and [VOLUME] down simulta-
neously.4. The repeat all mark blinks and then repeat 5 times limit is
released.
12
CX-LDB10/LDB20SECTION 5
MECHANICAL ADJUSTMENTS
TAPE MECHANISM DECK SECTIONPrecaution
1. Clean the following parts with a denatured alcohol-moistenedswab:
record/playback heads pinch rollerserase head rubber beltscapstan idlers
2. Demagnetize the record/playback head with a headdemagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to
the parts adjusted.5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque MeasurementMode Torque meter Meter reading
2.94 mN • m to 7.84 mN • m
FWD CQ-102C 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.14 mN • m to 0.59 mN • mFWD
CQ-102C 2 to 6 g • cmback tension
(0.02 – 0.08 oz • inch)
6.86 mN • m to 17.64 mN • m
FF/REW CQ-201B 71 to 143 g • cm
(0.98 – 1.99 oz • inch)
more than 0.98 N • m
FWD tension CQ-403A 100 g or more
(3.53 oz or more)
SECTION 6ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB = 0.775 V
Precaution1. Demagnetize the record/playback head with a head
demagnetizer.2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to
the parts adjust.4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuitadjustment should be completed before performing recordingcircuit adjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwisespecified.
Test TapeTape Signal Used for
P-4-A100 10 kHz, –10 dB Azimuth Adjustment
WS-48B 3 kHz, 0 dB Tape Speed Check
2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screwso that outputs match within 1dB of peak.
Screwposition
L-CHpeak
within1dB
Outputlevel
L-CHpeak
R-CHpeak
within1dB
Screwposition
R-CHpeak
Record/Playback Head Azimuth AdjustmentProcedure:
1. Mode: Playback
set
MAIN boardSPEAKER terminal (J302)L-CH, R-CH
+–
level meter
test tapeP-4-A100(10 kHz, – 10 dB)
13
CX-LDB10/LDB20
FOCUS BIAS CHECK
Adjustment and Connecting Location: CD board (See page 14)
Procedure :1. Connect the oscilloscope to TP (RFACO) and TP (VC) on the
CD board.2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)3. Press the [CD ] button.4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)A good eye pattern means that the diamond shape (◊) in thecenter of the waveform can be clearly distinguished.
• RF signal reference waveform (eye pattern)
CD SECTION
Note:1. CD Block is basically constructed to operate without
adjustment.2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.3. Use an oscilloscope with more than 10 MΩ impedance.4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with thefollowing checks.
5. Check the focus bias check when optical block is replaced.
+–
CD board
TP (RFACO)TP (VC)
oscilloscope (DC range)
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)TIME/DIV: 500 ns
1.1
When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.
0.2 Vp-p
NX
3. Mode: Playback
4. After the adjustments, apply suitable locking compound tothe parts adjusted.
Adjustment Location:Record/Playback/Erase Head
Tape Speed CheckMode: Playback
1. Insert the WS-48B into the deck.2. Press the H button on the deck.3. Confirm that the frequency counter reads 3,000 ± 90 Hz.
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)(WS-48B)
set
test tapeP-4-A100(10 kHz, – 10 dB)
R-CH
oscilloscope
L-CH
R-CH
V H
waveform of oscilloscope
in phase 45° 90° 135° 180°
good wrong
MAIN boardSPEAKER terminal (J302)L-CH
+–
set
test tapeWS-48B (3 kHz, 0 dB)
MAIN boardSPEAKER terminal (J302)L-CH, R-CH
frequency counter
14
CX-LDB10/LDB20
Checking Location:
TP (RFACO)
TP (VC)
– CD BOARD (Conductor Side) –
1515
CX-LDB10/LDB20
CX-LDB10/LDB20
SECTION 7DIAGRAMS
• Circuit Boards Location
For Schematic Diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF).
50 WV or less are not indicated except for electrolytics andtantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• f : internal component.• C : panel designation.
• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground un-
der no-signal (detuned) conditions.no mark: CD STOP
• Voltages are taken with a VOM (Input impedance 10 MΩ).Voltage variations may be noted due to normal productiontolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.
• Circled numbers refer to waveforms.• Signal path.F : TUNERJ : CD PLAYE : TAPE PLAYj : TAPE RECf : AUX IN
• AbbreviationAUS : Australian modelAR : Argentine modelE51 : Chilean and peruvian modelsKR : Korea modelMX : Mexican modelMY : Malaysia modelRU : Russian modelSP : Singapore model
For Printed Wiring Boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• W : indicates side identified with part number.• f : internal component.• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)
Note: The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Caution:Pattern face side : Parts on the pattern face side seen from(Conductor side) the pattern face are indicated.Parts face side : Parts on the parts face side seen from(Component side) the parts face are indicated.
• Indication of transistor.
C
B
These are omitted.
E
Q
B
These are omitted.
C E
Q
CD board
POWER (1) board
POWER (2) board
MAIN board
TUNER unit
CONTROL board
AUX board
HEADPHONE board
1616
CX-LDB10/LDB20
CX-LDB10/LDB20
7-1. BLOCK DIAGRAM — CD SECTION —
MIACK8PO11/BUCK/AD1436
MILP5
RESET2
MICS4
MIDIO6MICK7
MP3 DECODERIC301
A/DCONVERTER
CH2OUTF
CH2OUTR
23
24
22
4
5
6
7
17
18
16
15
RFACI
ASYO
ASYI
FILTER
FILO PCO
CLTV FILI
DIGITAL PLLASYMMETRYCORRECTOR
EFMDEMODULATOR
CD DSPIC101 (1/2)
MDP
DIGITALCLV
PROCESSOR
32KRAM
ERRORCORRECTOR
INTE
RNAL
BUS
SQCK
SQSO
EXCK
AOUT1
C4M XTSL
XTAO
XTAI
AOUT2R-CHD/A
DIGITALINTERFACE
D/ACONVERTER
SELECTOR
CLOCKGENERATOR
SUBCODEPROCESSOR
SCOR
WFC
KXU
GFGF
SEM
PH
SENS
DATA
CLOC
KXL
AT
SBSO
SENS
CD D
ATA
XLT
TEI
FEI
FOCUS/TRACKING/SLED
SERVO DSP
FOCU
S/TR
ACKI
NG/S
LED
PWM
GEN
ERAT
OR
SFDR
CH3FIN
CH4IN
CH3RIN
CH3OUTF
CH3OUTR
CH1FIN
CH1RIN
CH2FIN
CH2RIN
20
MUTE
SRDR
TFDR
TRDR
FFDR
FRDR
SSTP
COUT
MIRR,DFCT, FOKDETECTOR
SERVO AUTOSEQUENCER
SERVOINTERFACE
CPU INTERFACE
SCLK
TO CPU INTERFACE
FOKMIRRDFCT
2OPIN+
OPIN-
OUTVREF
CH4OUTF
CH4OUTR 27OPOUTM101
(SPINDLE)MOTORDRIVE
MOTORDRIVE
COILDRIVE
CH1OUTF
CH1OUTR
COILDRIVE
M
M
M102(SLED)
MOTOR/COIL DRIVEIC251
2-AXISDEVICE
(TRA
CKIN
G)(F
OCUS
)
CD DSPIC101 (2/2)
• Signal Path
: CD PLAY
14
13
11
12
SCOR
A MAIN Section
CD
13
11
12
9
10
14
119
108
21 23
312
7
TO SERVO AUTOSEQUENCER
42
51 53
XPCK
11250 52
45
46
6
XRST
100
X-RS
T
95
96 97
81
78
117 93
77
86
98 99115107102 105104 110111113 68
27
CD-C
LK
29 100
LRCK
BCK
PCM
D
LRCK
IA
SDI0
63 66 65
16
BCKI
A
15
SFSY
/LRC
KIB
19
SBSY
/BCK
IB
18 14
LRCK
IBC
KIPC
MDI
SDO0
62 60 61
1128 19
26
27
28
29
24
22
20
19
3736
E
B
A
D +3.3V
F
DETECTOR
A
B
C
D
RFSUMMING
AMP
FOCUSERROR
AMP
TRACKINGERROR AMP
RFACO
FEO
TEO
25VCVC
E
F
AUTOMATICPOWER
CONTROLQ10
APC LDAMP
LD
LD
VC
PD
LASER DIODE
OPTICAL PICK-UPBLOCK
(KSM-213EDP)
PD
I-V A
MP
D
C
EGIN
413534 EQ
AC_SUM RFAC
VCA
X17116.9344MHz
SYSTEM CONTROLLERIC401 (1/2)
S101(LIMIT)
MI-DIO-I 25MI-DIO-O 26
MI-CK 24MI-CS 4
MI-ACK 1MP3-REQ 3
MI-LP 5
MP3-RST 2
XTCN 94
STANDBY3MP3-STB 6
• R-ch is omitted due to same as L-ch.
XTACN95
26
1
1717
CX-LDB10/LDB20
CX-LDB10/LDB20
7-2. BLOCK DIAGRAM — MAIN SECTION —
ACDETECT
Q003,004
R-CH
+
21
INPUT SELECT,ELECTRICAL VOLUME
IC101
22
28REC-O-L
18OUT-L
13
CONT
21 CD-L
23 TUNER-L
2 TAPE-L
19 AUX-LR-CH
J702
REC/PBSWITCH
Q101,103,252-254
CDA
• Signal Path
: CD PLAY
: TAPE PLAY
: REC
• R-ch is omitted due to same as L-ch.
: TUNER
CD SERVOSection
: AUX IN
J701
LDB10
PHONES
SPEAKERIMPEDANCEUSE 6 – 16Ω
+–
–+
R
L J302
FM/AM TUNER PACK
TU LCH
TU RCH
TU CECE
R-CH
TUNEDTUNED
STEREOSTEREO
MUTETU-MUTING
TU DIDO
TU DODI
TU CLCLK
CETU
NED
STER
EODO DICL
K
RDS DATARDS DATA
RDS CLOCKRDS CLOCK
BIAS OSCT251
REC BIASSWITCH
Q256,257B +10V
BIAS OSCQ255
ERASE
HRPE(REC/PB/ERASE)
TAPE MECHANISMDECK BLOCK
L-CH
R-CH R-CH
DCDETECT
Q001,002,017
+
POWERAMPIC301
77
TU D
I
75
TU C
LOCK
73
TU C
E
72
TU T
UNED
71
TU S
TERE
O
76
TU D
O
RDS
DATA
RDS
CLOC
K
80
TA R
P
18
TA B
IAS
RDS-
DATA
RDS-
CLK
TU M
UTE
TU-M
UTIN
G
70 87
I-POW
ER_M
ONIT
OR
30
F-DA
TA
85
AMP
MUT
ECAPSTAN/REELMOTOR DRIVE
Q404,405
PLUNGERDRIVE
Q402,403
MM(CAPSTAN/REEL)
(DECK-A)
SOL 9V
MOTOR 9V
PACK
R RFCPLAY SWEND SW
TA PLAY SWTA END SW
838281
TA-SW
78 TA SOL
79 TA MO
RMC_IN7
SYSTEM CONTROLLERIC401 (2/2)
(EXCEPT SP, MY, E51)
(EXCEPT SP, MY, E51)
(SP, MY, E51)
FANFAN MOTOR
DRIVEQ601,602
+
D002
M+PV+3.6V
D602
–29VREGULATOR
Q013-016
(AC IN)
SUB POWERTRANSFORMER
T901
MAIN POWERTRANSFORMER
T902
AC 3.6V
SYS +3.3V
SYS +3.3V
TOFLUORESCENT
INDICATOR TUBEFL –29V
RECTD907-910
D408
D912
D911RECT
-35V
D905
AMP B+
TOPOWER AMP
AMP B–
VOLTAGESELECTOR
S901
+10VREGULATOR
IC003VM +10V
+3.9VREGULATOR
Q007-009
Q005
L : POWER ON
RECTD903,904
RECTD901,902
RECTD914,916
+3.3V(MAIN)
AM
ANTENNA
AUDIO IN
FM ANT
AM ANT
ANT GND
ANT GND
FM 75ΩCOAXIAL
VOLTAGEDETECTIC403
MAIN POWERRELAY DRIVE
Q006L : POWER ON
+3.3VREGULATOR
D012,015
AEP
LDB20
+3.3VREGULATOR
Q011,012
M +7V
CD +3.3V
CD +1.5V
M+7VREGULATOR
Q01092CD ON
86POWER ON
20I_POWER_DOWN
12RESET
REMOTE CONTROLRECEIVER
IC402
O-VO
L LE
D
91
LED DRIVEQ407
D410-415VOLUME
ST-B
Y LE
D
88
LED DRIVEQ408
D416(STANDBY)
X40132.768kHz
11 10
O-XT
2
I-XT1
15 13
X40216MHz
XOUT XI
N
FL401FLUORESCENT
INDICATOR TUBE
S1 – 16
G1 – G12
31 –
42
43-5
1,53
-59
97 VOL_ENCODER
KEY WAKE UPD420
74
69 CD OPEN
ROTARYENCODER
RV401VOLUME
S401-415(FRONT PANEL KEYS)
S820(CD LID OPEN/CLOSE DETECT)
KEY0,KEY189
,90
RESET SWITCHQ401
RY901
+1.5VREGULATOR
IC303
15
11
13
7
5
+INA
+INB
ST-B
Y
OUTA
OUTB
+
MUTEQ355
MUTEQ019
D006
VM+10V
SUB B+
SUB B+SWITCH
Q409
+3.3VREGULATOR
Q018
+3.6V
D009
D011LED+B
+10VREGULATOR
IC002
–29VREGULATOR
Q013-016
AC DETQ901-904
DC DETQ050,051
AMP B+AMP B–
-35V
FAN B+SW
Q603-605
OVERHEATDET
Q354
MUTEQ606 L : POWER ON
+14V
TH351
J701
LDB20
RY351
PHONES
SPEAKERIMPEDANCEUSE 6 – 16Ω
+–
–+
R
L J302
FANFAN MOTOR
DRIVEQ601,602
+ D602
FAN B+SW
Q603-605
MUTEQ606 L : POWER ON
+14V
RELAYSW
Q356
1818
CX-LDB10/LDB20
CX-LDB10/LDB20
7-3. PRINTED WIRING BOARD — CD BOARD — • See page 15 for Circuit Boards Location. :Uses unleaded solder.
C10
C260
C14
C15
C16
C18
C11
R405
C316
R354 R353
R352
R351
R302
R253
C315
R191
R172
R171
R162
R313
X171
R121
R12
R11
R10Q10
C116
C312
C184
C183
C303
C302
C305
C259C258
C257
C255
C203
C196
C195
C201
C182
C171
C172
C308
C151
C134
C125
C123
R165
R13
C17
FB30
1
C318
R201
C174R173
R205
C209
C210
C314
M102
S101
M101
IC251
IC101
CN101
CN201
R419
R412
R411
R410
R409
R408
R407
R406
R404
R403
R402
R401
R305
R303
R301
R252
R251
R182
R181
R163
R151
R143
R142
R141
R133
R132
R131R1
14R1
13
R112
R111
R307C311
C310
C309
C307
C306
C252
C251
C194
C181
C320
C163
C162
C143
C142
C141
C133 C132
C131
C124
C111
C122
C115
C114
C113
C112
C185
C186
R306
IC303
C317
R203
R161
C161
C211
C212
R204
C213
IC301
C313
M
E
(COMPONENT SIDE)CD BOARD
1-861-619-
12
(12)
30
31 60
120 91
1
61
90
(CONDUCTOR SIDE)CD BOARD
1-861-619-
12
(12)
(SPINDLE)
M (SLED)
13
54
116
17
32
64
49
4833
(LIMIT)
1
27
AMAIN
BOARDCN004
(Page 21)
TP(RFACO)OPTICAL
PICK-UPBLOCK
(KSM-213EDP/C2NP)
TP(VC)
1 7 148
28 22 1521
1 2
A
B
C
D
E
3 4 5 6 7 98 10
F
G
1211 13 1514 16 17
H
I
J
• SemiconductorLocation
Ref. No. Location
IC101 G-13IC251 D-10IC301 D-13IC303 B-14
Q10 F-7
1919
CX-LDB10/LDB20
CX-LDB10/LDB20
7-4. SCHEMATIC DIAGRAM — CD BOARD — • See page 32, 33 and 34 for IC Block Diagrams. • See page 31 for Waveforms.
/C2NP
MAIN BORAD(3/3)CN004
(Page 24)
R406
R407
R408
R409
R411
R412
R410
C151R203
C141
R143
R142
R141
C133
R133
R132
R131C134
TP12
5
TP12
4
C125 R121
C15
C122C123
C132
C142
R151
C111
C113
C112
C114
R111
TP429
TP428
TP430
TP431
C115
C195
TP432
IC101
C163
R163
C196
R162
C210
C194
R253TP418
JPO004C251R252R251
C16R12
JPO10 R11
C17
C18
R10
TP10
TP11
TP12
TP13
TP14
TP15
TP16
TP17
TP18
TP19
C182
C201
C181
C258
C257
C252
C255
C260
R181
R182
C183
C184
C203C162
C161
R161
R352 TP427
TP103
TP104
TP105
C209
TP43
6
TP42
0
TP42
1
C186
C185
R191
TP251
TP252
TP253
TP250
C306
R405
R404
R419
R403
R402
R401
R302
C317
R305
R301
C316C315
R313
C307
C302 C303C305 TP422
C312C313C314 C311 C309 C308
R303
C310
R353
R354
C11
C10
C14
C116
C318
R307
R351
TP433
TP187
TP401
TP409
TP411
TP410
TP434
TP419
TP412
TP413
TP414
TP415
TP416
TP417
TP408
TP407
TP406
TP405
TP404
TP403
TP402
TP186
R205
C320
C213
C212
C211
TP435
CN101
TP423
IC301
R173
Q10
C143
C171 R171
R172
R165
TP425
TP426
S101
C259
IC251
M102
M101
R201
R204
CN201
FB301
IC303
TP102
R306
R113
JPO102
JPO103
R13
TP424
R112
R114
TP17
7
C124
C172
C131
C174X171
100
100
100
100
100
100
100
10010V0
0.1
3.3k
1k
4.7k
0.01
180k
10k
1M0.1
RFAC
I
RFAC
O
0.1 15k
0.1
0.10.1
0.47
1500p
0
3300p
3300p
470p
470p
1k
FFDR
FRDR
TRDR
TFDR
0.1
0.1
MDP
CXD3059AR
0.1
100
0.1
47k
0.1
0.1
10kGAIN_SW
MDP6800p22k10k
1100k
APC 0
2204V
1000p
3.3
E
D
A
B
C
PD
F+
F-
T-
F-
0.1
10010V
0.1
0.1
0.1
0.1
0.1
22010V
100
100
226.3V
226.3V
10010V0.1
0.1
100
100
PCMDI
LRCK
PCMD
BCK
0.01
AVDD
AGND
DGND
470p
470p
0
SP+
SL+
SL-
SP-
0.1
100
100
100
100
100
100
10k
0.01
100k
100k
0.00220.1
220
0.1
0.1 0.12204V
MP3GND
0.10.1474V 0.1 0.1 47
4V
100k
0.1
100
100
10
10
0.1
10010V
0.01
10k
100
MP3VDD
MGND
MP3STB
DOUT
LOUT
ROUT
AVDD
XTCN
XRST
DATA
XLT
CLK
SENS
SCOR
MP3RST
MICS
MILP
MIDIO
MICK
MIACK
MP3REQ
MVDD
0 0
22p
22p
220p
DVDD
16P
IOP1
TC94A34FG-002
0
2SA2119K
0.1
22p 470
1M
0
SW+
SW-
0.1
BA5947FM-E2
27P
BH15FB1WG
F
0
1k
FEI
TEI
1
IOP2
15k
15k
VC
330p
27p
100p
0.116.9344MHz
E
F
F
E
D
A
B
C
MIACK
MICK
MIDIO
MILP
MICS
SCOR
SENS
CLOC
K
DATA
XRST
XLT
CLOCK
SENS
SCOR
XRST
MP3REQ
DATA
MP3STB
XTACN
XTAC
N
MP3STB
D
C
B
A
MP3RST
XLT
MP3REQ
MIACK
MICK
MIDIO
MILP
MICS
MP3RST
MDP
SFDR
SFDR
SRDR
SRDR
FRDR
FRDR
FFDR
FFDR
TFDR
TFDR
TRDR
TRDR
F+
F+
T+
T+
T-
T-
F-
F-
MDP
DOUT
DOUT
AOUT1
AOUT2
AOUT1
AOUT2
VC
VCC
PD
LD
T-
F-
T+
F+
VR
AGND
F
C
B
A
E
D
OPIN
-
OPIN
+ SW
CH1F
IN
CH1R
IN
CH2F
IN
CH2R
IN
GND
CNF4
POW
VCC
CH2O
UTR
CH2O
UTF
CH1O
UTR
CH4O
UTR
CH4O
UTF
CH3O
UTF
CH3O
UTR
POW
VCC
MUT
E
GND
CH3R
IN
CH3F
IN
CH4I
N
CH4C
APA
OUTV
REF
OPOU
T
PREV
CC
MIRR
NC
DFCT
FOK
VSS
LOCK
MDP
SSTP
IOVSS1
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
IOVDD1
AVDD0
AVSS0
NC
E
F
TEI
TEO
FEI
FEO
VC
A
B
C
D
NCAVDD
4
RFDC
O
PDSE
NS
AC_S
UM
EG_I
NLDPDRFC
AVSS
4
RFAC
O
RFAC
I
AVDD
3
BIAS
ASYI
ASYO NC
VPCO
VCTL
AVSS
3
CLTV
FILOFILI
PCO
AVDD
5
DDVR
OUT
DDVR
SEN
AVSS
5
DDCRNC
BCKI
LRCKI
LRCK
VSS
PCMD
BCK
VDD
EMPH
EMPHI
IOVDD2
DOUT
TEST
TEST1
IOVSS2
NC
XVSS
XTAO
XTAI
XVDD
AVDD1
AOUT1
VREFL
AVSS1
AVSS2
VREFR
AOUT2
AVDD2
NC
IOVDD0
RMUT
LMUT NC XTSL
IOVS
S0
XTAC
N
SQSO
SQCK
SBSO
EXCK
XRST
SYSM
DATA
VSS
XLAT
CLOC
K
VDD
SENS
SCLK
ATSK
WFC
K
XUGF
XPCK
GFS
C2PO
SCOR
VDD
C4M
WDC
K
COUT
PCMDI
VIN
GND
STBY
NCVOUT
LOUT
AGND
ROUT
MP3RST
DOUT
MGND
MP3GND
MILP
MICS
MP3REQ
MIACK
MIDIO
MICK
MP3STB
MP3(3.3V)
DVDD(3.3V)
AVDD(3.3V)
MGND
DGND
XTCN
SCOR
SENS
XLT
DATA
XRST
CLK
M+7V
SBSY
/BCK
IB
SFSY
/LRC
KIB
TXO
VDD
CKI/C
LOCK
/
IRQ/
FIO
VSS
PIO0
/SDI
2/IO
0
PIO1
/SDI
3/IO
1
PIO2
/IO2
PIO3
/IO3
PIO4
/FI1
/BUS
0/IO
4
PIO5
/FI2
/BUS
1/IO
5
PIO6
/FI3
/BUS
2/IO
7
PIO7
/BUS
3/IO
7
AD4/
PO04
AD3/
PO03
AD2/
PO02
AD1/
PO01
AD0/
PO00
VSS
VDD
CKO/
PO13
/AD1
6
VDDX
XO XI VSSX
TEST
MIM
D
VSSP
VCOI
VDDP
RESET
STANBY
MICS
MILP
MIDIO
MICK
MIACK
VDDT
VSS
BCKO
LRCKO
SDO0
SDI0
BCKIA
LRCKIA
DATA
SDI1/
SDO2
CS/RAS/
AD15/CAS/
PO12
SDO3/OE
PO11/BUCK/AD14
PO10/CCE/AD13
PO9/AD12
PO08/AD11
SRMSTB
VDDT
AD10
AD9
AD8
PO07/AD7
PO06/AD6
AD5/PO05
VDDM
WE/SDO1
AUTOMATIC
CD DSP
(LIMIT)
MOTOR/COIL
(SPINDLE)
(SLED)
+1.5V REGULATOR
MP3 DECODER
CONTROL
POWER
DRIVE
CH1O
UTF
2020
CX-LDB10/LDB20
CX-LDB10/LDB20
7-5. PRINTED WIRING BOARD — MAIN SECTION (1/2) — • See page 15 for Circuit Boards Location. :Uses unleaded solder.
(LDB20: AEP, RU)108 A-1095-628-A POWER (1) BOARD, COMPLETE
(LDB10: AEP, AR, KR, AUS, RU)
108 A-1108-995-A POWER (1) BOARD, COMPLETE (LDB20: E51)108 A-1109-028-A POWER (1) BOARD, COMPLETE
(LDB10: E51, SP, MY)
109 A-1109-035-A POWER (1) BOARD, COMPLETE (LDB10: MX)109 A-1095-601-A POWER (2) BOARD, COMPLETE (LDB20)109 A-1095-629-A POWER (2) BOARD, COMPLETE (LDB10)
0110 1-769-079-41 CORD, POWER (KR)0110 1-775-790-71 CORD, POWER (AUS)0110 1-827-226-31 CORD, POWER (MX)0110 1-829-387-11 CORD, POWER (AR)0110 1-830-188-11 CORD, POWER (AEP, E51, SP, MY, RU)
A-1095-579-A CONTROL BOARD, COMPLETE (LDB20: AEP)A-1095-619-A CONTROL BOARD, COMPLETE (LDB10: AEP)A-1108-989-A CONTROL BOARD, COMPLETE (LDB20: E51)A-1109-022-A CONTROL BOARD, COMPLETE
(LDB10: MX, AR, E51)A-1113-012-A CONTROL BOARD, COMPLETE (LDB20: RU)
A-1113-022-A CONTROL BOARD, COMPLETE (LDB10: RU)A-1116-003-A CONTROL BOARD, COMPLETE
IC401 6-805-229-01 IC M30392MCP-A08FPU0IC402 6-600-349-31 IC NJL24H400A ( )IC403 6-701-680-01 IC PST3629NR
< SHORT >
JC401 1-216-864-11 SHORT CHIP 0JC402 1-216-864-11 SHORT CHIP 0JC409 1-216-864-11 SHORT CHIP 0JC411 1-216-296-11 SHORT CHIP 0JC412 1-216-296-11 SHORT CHIP 0
JC413 1-216-296-11 SHORT CHIP 0JC414 1-216-864-11 SHORT CHIP 0 (MX)JC415 1-216-864-11 SHORT CHIP 0 (MX)JC416 1-216-296-11 SHORT CHIP 0 (MX)JC417 1-216-296-11 SHORT CHIP 0 (MX)
JC418 1-216-864-11 SHORT CHIP 0 (MX)JC419 1-216-296-11 SHORT CHIP 0 (MX)JC420 1-216-296-11 SHORT CHIP 0 (MX)JC421 1-216-296-11 SHORT CHIP 0 (MX)JC422 1-216-296-11 SHORT CHIP 0 (MX)
JC423 1-216-296-11 SHORT CHIP 0 (MX)JC424 1-216-296-11 SHORT CHIP 0 (MX)JC425 1-216-864-11 SHORT CHIP 0 (MX)
< COIL >
L401 1-216-296-11 SHORT CHIP 0L402 1-216-296-11 SHORT CHIP 0L403 1-216-296-11 SHORT CHIP 0
A-1095-588-A MAIN BOARD, COMPLETE (LDB20: AEP)A-1095-625-A MAIN BOARD, COMPLETE (LDB10: AEP)A-1108-992-A MAIN BOARD, COMPLETE (LDB20: E51)A-1109-025-A MAIN BOARD, COMPLETE
(LDB10: MX, SP, MY, E51)A-1113-015-A MAIN BOARD, COMPLETE (LDB20: RU)
A-1113-025-A MAIN BOARD, COMPLETE (LDB10: RU)A-1119-304-A MAIN BOARD, COMPLETE
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.