Top Banner
BUTTERFLY VALVES HYFLO MKV CAST IRON 2.1 HYFLO MKV DUCTILE IRON 2.6 HYFLO MKV WATERMARK 2.8 (UCV) CAST IRON 2.11 STAINLESS STEEL HYGIENIC 2.13
14

Butterfly Valve

Jul 21, 2016

Download

Documents

Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: Butterfly Valve

butterfly valveshyflo mkv cast iron 2.1

hyflo mkv ductile iron 2.6

hyflo mkv watermark 2.8

(ucv) cast iron 2.11

stainless steel hygienic 2.13

Page 2: Butterfly Valve

June 20102.1

butterfly valves hyflo

mkv ca

st iron

hyflo mkv cast iron butterfly valve

SpecificationGeneral purpose butterfly valve.conforms to en 593 standards.iso 9001 certified manufacturer.Wafer or lugged cast iron body.stainless steel disc and stem.ePDm or nbr seats. as2129 table e flange connection as standard. ansi‑bs16.1/5 #125/150 connection available on request.

DeSign featureS1. aGa approved for gas service. aGa certificate no. 4030 applies

to Dn50‑Dn150 valves to a maximum pressure of 8 bar (800 kPa) with an nbr seat. available to suit table e or ansi 150 flanges.

2. the operating lever is cast ductile iron for long life in all but the most corrosive environments.

3. lever handles have s/s 304 10 position notch plates and memory stop plates are also available. Gear operators have an infinite number of positions.

4. a raised key section on the liner fits into a matching keyway on the inside of the valve body to provide greater flexibility at the disc seating area and prevent liner ‘roll‑out’, a condition where the seat can come away from the body when high velocities occur or the valve is installed incorrectly.

5. the moulded seat design is easily replaced in the field, provides isolation of the body from the service fluid and acts as a gasket face for sealing.

6. the acetal bushing takes care of any operator induced side thrust loads and when combined with chevron type secondary stem seal ensures trouble free operation.

7. the webbed flange design of wafer body ensures correct and positive alignment between flanges ‑ one of the criteria for good butterfly valve operation.

8. the valve has an extended neck for insulated pipe services.

9. Pinless disc design, eliminates one less leak path past the disc.

10. valves can also be supplied with pneumatic, electric or hydraulic actuators and with all accessories such as limit switches, solenoid valves, manual override etc.

11. valves can also be supplied with the disc diameter undercut to ensure minimum torque and smallest possible actuator size for throttling or low pressure shut‑off actuated valve applications.

12. the hyflo mkv has a spherically machined disc to ensure improved sealing from valve internals under higher operating pressures. stem and bushings etc never come into contact with service fluid.

supplied as standard with either lever or gearbox.

an extra leaver, gearbox, spare seats and memory stop kits can also be supplied separately.

note: for matching bolt and nut sizes, lengths and qty’s refer to page 1.26 of tradelink industrial catalogue.

note: for service other than hvac water and aGa service please consult for compatibility of seat elastomer and disc material with service fluid.

preSSure/temperature ratingfor general fluid service up to 1400 kPa (200Psi). Lugged valve suitable for full rated pressure in downstream dismantled condition, provided all installation requirements are met.aGa approved to 800 kPa (116Psi) for sizes Dn50‑Dn150 with nbr seat.nbr seat: ‑10°c to +90°c (0°c to +80°c continuous).ePDm seat: ‑15°c to +120°c (‑5°c to +100°c continuous).

materiaL Specificationref. component material1 body cast iron2 Disc 304 stainless steel3 seat ePDm or nitrile (nbr)*4 upper stem 304 stainless steel5 lower stem 304 stainless steel6 Packing ePDm or nitrile (nbr)*7 Packing Gland acetal8 snap ring carbon steel9 top retainer 304 stainless steel 10 top retainer bolts 304 stainless steel11 bottom Plug nickel Plated mild steel12 operating lever cast Ductile iron13 notch Plate 304 stainless steel

* ePDm as standard, nbr for aGa approved valves.

Page 3: Butterfly Valve

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.2.2

butt

erfl

y va

lves

hyf

lo m

kv c

ast

iro

n

hyflo mkv cast iron butterfly valve

Gearbox

VaLVe DimenSionS - mm

size 50 65 80 100 125 150 200 250 300

Ød 51.5 63.5 78.0 101.5 125.0 148.0 198.0 248.0 298.0

Øg 90 107 125 146 179 206 257 312 362

h1 75 80 100 110 123 143 175 210 245

h2 130 137 157 171 184 203 238 270 310

h3 33 33 33 33 33 33 33 65 65

h4 238 250 290 314 340 379 446 545 620

l 43 46 46 52 56 56 60 68 78

t 12 12 12 12 12 12 12 16 16

ØW 32 47 66 89 113 139 191 242 291

a 9.5 9.5 11.8 11.8 14.5 14.5 14.5 * *

B 30 30 30 30 30 30 30 60 60

ØD 14 14 16 16 19 19 19 22 28

kg waf 2.8 3.7 4.2 4.8 7.1 8.8 13 20 38

kg lugg 3.9 5.0 6.6 8.2 10 12 19 30 47

* Dn250‑Dn300 are keyway instead of double D, keyway width x depth 8 x 4, key 8 x 7. Weight in kg is approximate only.

lugged style

gearbox DimenSionS - mm

to fit size 50 65 80 100 125 150 200 250 300

e 45 45 45 45 45 45 45 63 63

h 74 74 74 74 74 74 74 85 85

l 165 165 165 165 165 165 185 250 250

W 150 150 150 150 180 180 220 260 260

kg 5.5 5.5 5.5 5.5 5.5 5.5 6.5 9.5 9.5

fLange DriLLing DimenSionS aS2129 ‘e’ - mm

size 50 65 80 100 125 150 200 250 300

ØPcD 114 127 146 178 210 235 292 356 406

n 4 4 4 8 8 8 8 12 12

h waf 18 18 18 18 18 22 22 22 26

h lugg m16 m16 m16 m16 m16 m20 m20 m20 m24

for ansi flange drilling dimensions see page 1.18.

Wafer style

Page 4: Butterfly Valve

June 20102.3

butterfly valves hyflo

mkv ca

st iron

hyflo mkv cast iron butterfly valve

Dn250 ‑ Dn300Dn50 ‑ Dn200

LeVer HanDLe DimenSionS - mm

size 50 65 80 100 125 150 200 250 300

a 9.5 9.5 11.8 11.8 14.5 14.5 14.5 ‑ ‑

B 23 23 23 23 23 23 23 62 62

l 285 285 285 285 285 285 385 485 485

kg 0.88 0.88 0.88 0.88 0.88 0.88 1.03 2.7 2.7

VaLVe fLow coefficientS - cv (uSgpm)

size 50 65 80 100 125 150 200 250 300

20° open 10.8 18.3 27.8 42.3 68.3 97.6 173.5 271.0 390.3

30° open 16.4 27.6 41.8 65.0 101.9 147.4 261.3 409.8 588.7

40° open 25.5 43.0 65.4 101.9 159.4 229.8 408.7 637.5 918.2

50° open 41.6 70.1 106.6 165.9 260.2 375.1 666.7 1040.7 1499.3

60° open 67.3 114.0 171.9 269.9 419.6 607.1 1079.8 1686.9 2429.5

70° open 108.4 184.1 278.5 435.8 680.8 979.0 1741.1 2720.0 3918.0

80° open 167.3 282.2 428.0 667.8 1045.1 1504.7 2674.5 4179.3 5083.4

90° fully open 200.0 338.4 512.1 800.1 1250.0 1800.7 3201.4 5003.2 7203.9

cv = 1.16 kv

VaLVe operating torque - nm

size 50 65 80 100 125 150 200 250 300

dP 6 Bar 18 23 30 38 57 85 158 250 347

dP 10 Bar 21 26 32 50 65 98 169 292 501

dP 16 Bar 23 27 35 51 79 112 239 356 525

based on water as the fluid with temperature range +1°c to +80°c. at least one operation cycle per month and a flow velocity in the pipe not more than 4m/s.

top flange lever

top fLange mounting DimenSionS to iSo5211

size 50 65 80 100 125 150 200 250 300

type f07 f07 f07 f07 f07 f07 f07 f10 f10

Øn 90 90 90 90 90 90 90 125 125

Øm 70 70 70 70 70 70 70 102 102

m 4 4 4 4 4 4 4 4 4

Øz 10 10 10 10 10 10 10 12 12

Page 5: Butterfly Valve

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.2.4

butt

erfl

y va

lves

hyf

lo m

kv c

ast

iro

n

hyflo mkv cast iron butterfly valve

before inStaLLation cHeck

1. Pipe flanges are free from weld spatter or swarf.

2. the flanges are on the same centreline and their faces are parallel.

3. the pipe internal does not contain objects that will obstruct the disc from fully opening.

4. the pipe flanges internal diameters are within the above minimum and maximum dimensions. this is to make sure the disc does clear the inside of the flange and the flange fully seals with the raised gasket face of the seat.

5. Do not weld near the valve.

6. Do not use flange gaskets or sealing compounds.

inStaLLation

1. operate valve fully before and after installation.

2. semi‑open the valve so that the disc does not protrude outside of body. this prevents damage to the disc and reduces initial torque.

3. separate pipe flanges enough to clear valve body and liner faces to prevent damage to the seat during installation. insert valve.

4. manually loose fit flange bolts and centre valve bore with pipe/flange bore.

5. open valve fully to ensure no contact between disc and pipe or flanges.

6. Progressively tighten bolts in diagonal sequence until metal to metal contact is achieved between the valve body and flanges.

7. operate valve several times to ensure no obstruction to disc travel.

correct inStaLLation

pipe fLange iD - mm

size 50 65 80 100 125 150 200 250 300

min iD 47 60 72 96 122 148 198 248 298

max iD 60 76 90 114 140 168 219 275 323

Page 6: Butterfly Valve

June 20102.5

butterfly valves hyflo

mkv ca

st iron

hyflo mkv cast iron butterfly valve

HyfLo mkV caSt iron butterfLy VaLVe coDeS

comPlete ePDm t/e valves 50 65 80 100 125 150 200 250 300

lugged w/-lever 076716 076717 076718 076719 076720 076721 076722 076723 076724

Wafer w/-lever 076728 076729 076730 076731 076732 076733 076734 076735 076736

lugged w/-gearbox 076742 076743 076744 076745 076747 076748 076749 076750 076753

Wafer w/-gearbox 076660 076661 076662 076663 076664 076665 076666 076668 076669

aGa luGGeD nBr valves 50 65 80 100 125 150

table e 076648 076649 076650 076651 076652 076653

ansi 150 (imP) 076871 076872 076874 076875 076876 076877

ansi 150 (metric) 076849 076850 076852 076854 076856 076878

nBr t/e lugged lever 076659

sPares 50 65 80 100 125 150 200 250 300

Gear Box 076686 076686 076687 076687 076688 076688 076689 076690 076691

memory stop kit 075090 075090 075091 075091 075092 075092 075092

lever kit 076837 076837 076838 076838 076839 076839 076840 076841 076842

spare seats for previous models

ePDm mkiv seat 075341 075342 075343 075344 075345 075346 075347 075348 075349

nBr mkiv seat 075516 075517 075518 075519 075520 075521 075522 075523 075524

mk3 ePDm 075000 075004 075006 075008 075009 075010 075012 075013 075014

mk3 nBr 075016 075017 075018 075019 075024 075040 075042 075047 075048

mk2 ePDm 076637 076639 076641 076643 076644 076645 076647 076657 076667

mk2 nBr 076676 076677 076678 076679 076680 076681 076682 076683 076684

mk1 nBr 076671 076675 076685 076696 076698

standard valves ‑ ePDm seat, aGa valves ‑ nbr seat.

gear operator reDuction ratioS

Dn50 - Dn200 24:1

Dn250 - Dn300 30:1

memory stop kit

Page 7: Butterfly Valve

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.2.6

butt

erfl

y va

lves

hyf

lo m

kv D

uct

ile

iro

n

hyflo mkv Ductile iron butterfly valve

SpecificationGeneral purpose butterfly valve.conforms to en 593 standards.iso 9001 certified manufacturer.Wafer or lugged ductile iron body.stainless steel disc and stem.ePDm seats.as2129 table e flange connection as standard. ansi‑bs16.1/5 #125/150 connection available on request.

preSSure/tempurature ratingfor general fluid service up to 1400 kPa (200psi). lugged valve suitable for 60% of full rated pressure, 800 kPa, in downstream dismantled condition, provided all installation requirements are met.ePDm seat: ‑15°c to +120°c (‑5°c to +100°c continuous).

materiaL Specificationref. component material1 body Ductile iron2 Disc 304 stainless steel3 seat ePDm 4 upper stem 304 stainless steel5 lower stem 304 stainless steel6 Packing ePDm 7 Packing Gland brass 8 snap ring carbon steel9 top retainer nickel Plated or epoxy Plated steel10 top retainer bolts nickel Plated mild steel11 bottom cover nickel Plated or epoxy Plated steel12 bottom bolts nickel Plated mild steel

lugged style

Wafer style

VaLVe DimenSionS - mm

size 350 400 450 500 600

Ød 346.0 395.0 452.0 489.5 579.0

Øg 410 468 526 577 677

h1 280 315 335 385 450

h2 325 375 400 435 500

h3 65 75 75 100 100

h4 670 765 810 920 1050

l 78 102 114 127 154

t 17 20 20 23 23

ØW 343 386 438 476 562

B 60 70 70 90 90

ØD 28 38 38 45 55

key 8x7 12x8 12x8 14x9 14x9

t1 4.0 5.0 5.0 5.5 5.5

t2 3.0 3.0 3.0 3.5 3.5

b 8.0 12.0 12.0 14.0 14.0

kg waf 39 75 92 110 169

kg lugg 59 82 110 162 264

Weight in kg is approximate only.

for further details on installation of rubber lined butterfly valves see page 2.4.

note: for matching bolt and nut sizes, lengths and qty’s refer to page 1.26 of tradelink industrial catalogue.

note: for service other than hvac water please consult for compatibility of seat elastomer and disc material with service fluid.

Page 8: Butterfly Valve

June 20102.7

butterfly valves hyflo

mkv Du

ctile iron

hyflo mkv Ductile iron butterfly valve

VaLVe fLow coefficientS - cv (uSgpm)

size 350 400 450 500 600

20° open 532.3 694.9 878.1 1085.2 1562.2

30° open 802.2 1047.3 1324.8 1635.9 2356.9

40° open 1250.0 1632.7 2066.3 2550.9 3674.1

50° open 2040.3 2665.8 3372.7 4164.1 5996.2

60° open 3292.4 4318.0 5462.0 6746.4 9714.7

70° open 5331.7 6964.3 8813.8 10882.3 15669.8

80° open 8190.5 10698.0 13540.6 16715.9 24070.5

90° fully open 9804.7 12806.6 16208.6 20010.5 28814.6

cv = 1.16 kv

top fLange DimenSionS to iSo5211

size 350 400 450 500 600

type f10 f14 f14 f16 f16

Øn 125 175 175 210 210

Øm 102 140 140 165 165

m 4 4 4 4 4

Øz 12 18 18 22 22

VaLVe operating torque - nm

size 350 400 450 500 600

dP 6 Bar 499 697 936 1208 2535

dP 10 Bar 619 802 1150 1485 2955

dP 16 Bar 1389 1851 2264 2791 5155

based on water as the fluid with temperature range +1°c to +80°c. at least one operation cycle per month and a flow velocity in the pipe not more than 4m/s.

gearbox DimenSionS - mm

to fit size 350 400 450 500 600

e 63 82 82 100 100

h 85 90 90 112 112

W 315 405 405 405 405

l 250 300 300 310 310

kg 10 19 19 32 32

traDeLink inDuStriaL HyfLo mkV DuctiLe iron butterfLy coDeS

comPlete valve 350 400 450 500 600

lugged w/-gearbox 076755 076761 076763 076765 076769

Wafer w/-gearbox 076670 076672 076673 076708 076714

spares

Gearbox 076692 076694 076694 076704 076704

ePDm seat 075350 075351 075352 075353 075356

nBr seat 075525 075526 075527 075528 075530

Gearbox

gear operator reDuction ratioS

Dn350 30:1

Dn400 - Dn450 40:1

Dn500 - Dn600 50:1

pipe fLange iD - mm

size 350 400 450 500 600

min iD 350 395 450 485 570

max iD 361 412 463 510 585

fLange DriLLing DimenSionS aS2129 ‘e’ - mm

size 350 400 450 500 600

ØPcD 470 521 584 641 756

n 12 12 16 16 16

h waf 26 26 26 26 33

h lugg m24 m24 m24 m24 m30

for ansi flange drilling dimensions see page 1.18.

top flange

Page 9: Butterfly Valve

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.2.8

hyflo mkv Watermark butterfly valve

Specification Potable water service butterfly valve. Watermark approval evaluated to ats 5200.012 ‑ 2005certificate no. Wmka20022. conforms to en 593 standards.iso 9001 certified manufacturer.cast iron body with fbe coating to 350 microns.lugged valve body pattern stocked as standard.Wafer valve body available on request.ePDm grade seats in accordance with as 4020.as2129 table e flange connection as standard.valve sizes stocked with lever Dn50 to Dn150, with gear operator Dn100 to Dn300.top flange mounting dimensions to iso5211.

materiaL Specificationref. component material1 body cast iron with fbe coating 350 microns2 Disc cf8m stainless steel3 seat Peroxide cured ePDm to as 40204 upper stem 316 stainless steel5 lower stem 316 stainless steel6 Packing ePDm7 Packing Gland acetal8 snap ring carbon steel9 top retainer 304 stainless steel10 top retainer bolts 304 stainless steel11 bottom Plug nickel Plated mild steel12 operating lever cast Ductile iron13 notch Plate 304 stainless steel

DeSign featureS 1. Watermark approval to ats 5200.012 ‑ 2005, certificate no.

Wmka20022 for potable water service in valve sizes Dn50 to Dn300.

2. supplied as standard with either a lever (Dn50‑Dn150) or gearbox (Dn100‑Dn300). memory stop kits or actuators and accessories are available.

3. Distinquishable from the standard hyflo mkv valve because of the valve colour, the Watermark valve is blue, the standard valve is green with a yellow lever

4. seat design to prevent 'roll out' when high velocities occur or valve is installed incorrectly.

5. seat design is easily replaced in the field, isolates the fluid from the valve body and acts as a gasket face for seating.

6. the acetal bushing and chevron secondary stem seal ensures trouble free operation.

7. the valve has an extended neck for insulated pipe services.

8. Pinless disc design eliminates one less leak path.

9. the hyflo mkv has a spherically machined disc to ensure improved sealing from valve internals under higher operating pressures. stem and bushings etc never come into contact with service fluid.

preSSure/temperature ratingS for potable water service up to 1400 kPa (200 Psi). lugged valve suitable for full rated pressure in downstream dismantled condition, provided all installation requirements are met.ePDm seat: ‑15°c to +120°c (‑5°c to +100°c continuous)

note: for matching bolt and nut sizes. lengths and qty's refer to page 1.26. for installation instructions refer to page page 2.4. for top flange mounting dimensions to iso5211 refer to page 2.3.

note: for service other than Potable water please consult with us for compatibility of seat elastomer and disc materials with service fluid.

butt

erfl

y va

lves

hyf

lo m

kv W

ater

ma

rk

memory stop kit

Page 10: Butterfly Valve

June 20102.9

butterfly valves hyflo

mkv W

aterma

rk

hyflo mkv Watermark butterfly valve

VaLVe DimenSionS - mm

size 50 65 80 100 125 150 200 250 300

Ød 51.5 63.5 78.0 101.5 125.0 148.0 198.0 248.0 298.0

Øg 90 107 125 146 179 206 257 312 362

h1 75 80 100 110 123 143 175 210 245

h2 130 137 157 171 184 203 238 270 310

h3 33 33 33 33 33 33 33 65 65

h4 238 250 290 314 340 379 446 545 620

l 43 46 46 52 56 56 60 68 78

t 12 12 12 12 12 12 12 16 16

ØW 32 47 66 89 113 139 191 242 291

a 9.5 9.5 11.8 11.8 14.5 14.5 14.5 * *

B 30 30 30 30 30 30 30 60 60

ØD 14 14 16 16 19 19 19 22 28

kg waf 2.8 3.7 4.2 4.8 7.1 8.8 13 20 38

kg lugg 3.9 5.0 6.6 8.2 10 12 19 30 47

* Dn250‑Dn300 are keyway instead of double D, keyway width x depth 8x4, key 8x7. Weight in kg is approximate only.

gearbox DimenSionS - mm

to fit size 50 65 80 100 125 150 200 250 300

e 45 45 45 45 45 45 45 63 63

h 74 74 74 74 74 74 74 85 85

l 165 165 165 165 165 165 185 250 250

W 150 150 150 150 180 180 220 260 260

kg 5.5 5.5 5.5 5.5 5.5 5.5 6.5 9.5 9.5

Gearboxlugged style Wafer style

fLange DriLLing DimenSionS aS2129 ‘e’ - mm

size 50 65 80 100 125 150 200 250 300

ØPcD 114 127 146 178 210 235 292 356 406

n 4 4 4 8 8 8 8 12 12

h waf 18 18 18 18 18 22 22 22 26

h lugg m16 m16 m16 m16 m16 m20 m20 m20 m24

for ansi flange drilling dimensions see page 1.18.

Page 11: Butterfly Valve

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.2.10

butt

erfl

y va

lves

hyf

lo m

kv W

ater

ma

rk

hyflo mkv Watermark butterfly valve

VaLVe fLow coefficientS - cv (uSgpm)

size 50 65 80 100 125 150 200 250 300

20° open 10.8 18.3 27.8 42.3 68.3 97.6 173.5 271.0 390.3

30° open 16.4 27.6 41.8 65.0 101.9 147.4 261.3 409.8 588.7

40° open 25.5 43.0 65.4 101.9 159.4 229.8 408.7 637.5 918.2

50° open 41.6 70.1 106.6 165.9 260.2 375.1 666.7 1040.7 1499.3

60° open 67.3 114.0 171.9 269.9 419.6 607.1 1079.8 1686.9 2429.5

70° open 108.4 184.1 278.5 435.8 680.8 979.0 1741.1 2720.0 3918.0

80° open 167.3 282.2 428.0 667.8 1045.1 1504.7 2674.5 4179.3 5083.4

90° fully open 200.0 338.4 512.1 800.1 1250.0 1800.7 3201.4 5003.2 7203.9

cv = 1.16 kv

VaLVe operating torque - nm

size 50 65 80 100 125 150 200 250 300

dP 6 Bar 18 23 30 38 57 85 158 250 347

dP 10 Bar 21 26 32 50 65 98 169 292 501

dP 16 Bar 23 27 35 51 79 112 239 356 525

based on water as the fluid with temperature range +1°c to +80°c. at least one operation cycle per month and a flow velocity in the pipe not more than 4m/s.

traDeLink inDuStriaL HyfLo mkV watermark butterfLy VaLVe coDeS

size 50 65 80 100 125 150 200 250 300

lugged w/- lever 074604 074605 074606 074607 074608 074609

lugged w/- gear op 074610 074611 074612 074613 074614 074615

Dn250 ‑ Dn300Dn50 ‑ Dn200

lever

LeVer HanDLe DimenSionS - mm

size 50 65 80 100 125 150 200 250 300

a 9.5 9.5 11.8 11.8 14.5 14.5 14.5 ‑ ‑

B 23 23 23 23 23 23 23 62 62

l 285 285 285 285 285 285 385 485 485

kg 0.88 0.88 0.88 0.88 0.88 0.88 1.03 2.7 2.7

Page 12: Butterfly Valve

June 20102.11

(ucv) cast iron butterfly valve

Specificationthrottling or low pressure applications for mechanical services or general industry. conforms to bs5155 specification, wafer, cast iron body, stainless steel disc and stem, ePDm seat, as2129 table e flange connection as standard. operator mounting in accordance with iso 5211/1/2/3.

preSSure/temperature ratingfor general fluid service up to 300 kPa (43psi).120°c ePDm ‑ food grade.

Valve Velocity Limitsfluids 10 m/sGases 65 m/s

materiaL Specificationref. component material1 bushing acetal2 stem 316 stainless steel3 Disc 316 stainless steel4 body cast iron5 seat ePDm

DeSign featureS1. the Disc diameter is undercut to ensure minimum torque and

smallest possible actuator size for throttling or low pressure shut‑off actuated valve applications.

2. Pinless Disc design eliminates possible leak path or risk of pin failure.

3. stem rention via circlip ensures stem cannot blow out if the valve is over pressurised.

4. Primary and secondary sealing features, an interference fit between seat and disc, and seat and stem, do not rely on outside flanges.

5. seat retention design minimises distortion/movement of the seat.

6. moulded double o‑rings on the seat between the seat and the flange, and seat and stem surface maximise sealing.

7. seat is not bonded to the body and is replaceable, enabling extended service life.

8. extended neck design for insulated pipe services.

9. locating holes on the body wafer essential for alignment and proper installation.

10. Disc is manufactured from 316 stainless steel for corrosion protection.

butterfly valves (ucv) ca

st iron

Page 13: Butterfly Valve

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.2.12

(ucv) cast iron butterfly valve

butt

erfl

y va

lves

(u

cv) c

ast

iro

n

traDeLink inDuStriaL (ucV) caSt iron butterfLy coDeS

size 50 65 80 100 125 150 200 250 300

Wafer 075058 075059 075060 075061 075062 075063 075064

top fLange DimenSionS

no. holes 4 4 4 4 4 4 4 4 4

Dia. holes 9 9 9 9 9 9 11 11 11

Bolt circle 70 70 70 70 70 70 102 102 102

standard valves are bareshafted for actuation.

weigHt - kg

size 50 65 80 100 125 150 200 250 300

kg 2.9 3.8 4.3 5.4 7.2 9 15.8 22.6 39.4

VaLVe operating torque - nm

size 50 65 80 100 125 150 200 250 300

Wet 3 Bar 7.5 8.5 13 17 26 38 68 114 163

Dry 3 Bar 11 13 20 25 49 57 102 171 244

VaLVe DimenSionS - mm

size 50 65 80 100 125 150 200 250 300

a 90 90 90 90 90 90 127 127 127

B 32 32 32 32 32 32 32 50 50

c 140 152 159 178 191 203 241 273 311

D 42.9 46 46 52.3 55.6 55.6 60.5 68.3 77.7

e 94 112 128 158 190 210 266 330 375

f 53 68 82 103 129 152 202 252 302

G 55 65 75 94 105 123 149 198 225

h 30.6 50 69 89 115.6 141.5 192.3 242.6 292.5

shaft Dia 14.0 14.0 14.0 19.1 19.1 22.0 22.0 30.0 30.0

shaft flat 9.5 9.5 9.5 12.7 12.7 15.9 15.9 24.0 24.0

VaLVe fLow coefficientS - uSgpm

size 50 65 80 100 125 150 200 250 300

20° 7 10 15 26 43 59 108 178 256

30° 16 23 36 61 98 138 247 396 587

40° 28 42 65 108 177 247 437 705 995

50° 49 68 109 178 278 398 687 1100 1697

60° 77 108 167 275 447 637 1100 1795 2695

70° 128 178 278 458 737 1097 1795 2995 4398

80° 198 288 427 715 1095 1590 2790 4590 6790

90° open 219 316 498 815 1290 1895 3290 5390 7990

Page 14: Butterfly Valve

June 20102.13

butterfly valves stain

less steel hyG

ienic

stainless steel hyGienic butterfly valve

operating torque - nm

size 25 40 50 65 80 100

torque 8 12 14 22 28 36

also available with mounted actuator.

Specificationhygienic butterfly valve.fully forged stainless steel. finish body 180 grit ‑ disk 400 grit. spring loaded lever with four (4) locking positions. buttweld connection.all parts are interchangeable within the respective size.

preSSure/temperature ratingup to 1100 kPa (160psi) at 170°c or down to minus 50°c in closed position.

materiaL Specificationref. component material1 body 316 stainless steel2 Disc 316 stainless steel3 stem 316 stainless steel4 liner silicon as standard5 handle 316 stainless steel6 handle Grip Plastic

available with silicon or viton replaceable trim.

DimenSionS - mm

size 25 40 50 65 80 100

a 121 121 121 121 162 162

B 24 24 26 27 32 40

traDeLink inDuStriaL generic Hygienic butterfLy coDeS

size 25 32 40 50 65 80 100

304 ss 088101 088103 088105 088107 088109 088111

316l ss 088113 088115 088117 088119 088127 088121 088123

314 088125

lever, 4 position 088129 088131