Top Banner
Linear Motion and Assembly Technologies Service Pneumatics Hydraulics Electric Drives and Controls Contents Ordering Code / Standard Program 2 Technical Data 3...7 Ordering Code / Unit Dimensions, Size 5 8 Unit Dimensions, Sizes 10, 12, 16 9 Unit Dimensions, Sizes 23, 28, 32 10 Unit Dimensions, Size 45 11 Unit Dimensions, Sizes 56, 63 12 Unit Dimensions, Sizes 80, 90 13 Unit Dimensions, Sizes 107, 125 14 Unit Dimensions, Sizes 160, 180 15 Unit Dimensions, Size 200 16 Unit Dimensions, Size 250 17 Unit Dimensions, Size 355 18 Unit Dimensions, Size 500 19 Unit Dimensions, Size 710 20 Unit Dimensions, Size 1000 21 Installation Notes 22 General Notes 24 Features – Fixed pump with axial tapered piston rotary group of bent axis design, for hydrostatic drives in open circuits – For use in mobile and stationary application areas – Output flow is proportional to drive speed and displacement – The drive shaft bearings are designed to give the service life expected in these areas of operation – High power density – Compact design – High overall efficiency – Economical conception – One piece pistons with piston rings Axial Piston Fixed Pump A2FO RE 91401/03.08 1/24 Replaces: 09.07 Technical data sheet Series 6 Sizes Nominal pressure/Peak pressure 5 315/350 bar 10 to 200 400/450 bar 250 to 1000 350/400 bar Open circuits
24
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Linear Motion andAssembly Technologies ServicePneumaticsHydraulics

Electric Drives and Controls

ContentsOrdering Code / Standard Program 2

Technical Data 3...7

Ordering Code / Unit Dimensions, Size 5 8

Unit Dimensions, Sizes 10, 12, 16 9

Unit Dimensions, Sizes 23, 28, 32 10

Unit Dimensions, Size 45 11

Unit Dimensions, Sizes 56, 63 12

Unit Dimensions, Sizes 80, 90 13

Unit Dimensions, Sizes 107, 125 14

Unit Dimensions, Sizes 160, 180 15

Unit Dimensions, Size 200 16

Unit Dimensions, Size 250 17

Unit Dimensions, Size 355 18

Unit Dimensions, Size 500 19

Unit Dimensions, Size 710 20

Unit Dimensions, Size 1000 21

Installation Notes 22

General Notes 24

Features– Fixed pump with axial tapered piston rotary group of bent

axis design, for hydrostatic drives in open circuits

– For use in mobile and stationary application areas

– Output flow is proportional to drive speed and displacement

– The drive shaft bearings are designed to give the service life expected in these areas of operation

– High power density

– Compact design

– High overall efficiency

– Economical conception

– One piece pistons with piston rings

Axial Piston Fixed Pump A2FO

RE 91401/03.08 1/24Replaces: 09.07

Technical data sheet

Series 6 Sizes Nominal pressure/Peak pressure 5 315/350 bar 10 to 200 400/450 bar 250 to 1000 350/400 bar Open circuits

Page 2: BOSCH REXROTH Axial Piston Fixed Pump a2fo

�/24 Bosch Rexroth AG A�FO RE 91401/03.08

Hydraulic fluid

01

Mineral oil and HFD. HFD for sizes 250 to 1000 only in combination with long-life bearing “L“ (no code)

HFB-, HFC hydraulic fluid Sizes 10 to 200 (no code)

Sizes 250 to 1000 (only in combination with long-life bearing “L“) E-

Axial piston unit02 Bent axis design, fixed A�F

Drive shaft bearing 10 to �00 �50 to 500 710 to 1000

03Standard bearing (no code) –

Long-life bearing – L

Operation mode04 Pump, open circuits O

Size

05≈ Displacement Vg (cm3)

10 1� 16 �3 �8 3� 45 56 63 80 90 107 1�5 160 180 �00 �50 355 500 710 1000

Series06 6

Index

07

sizes 10 to 180 1

size 200 3

sizes 250 to 1000 0

Direction of rotation

08Viewed from shaft end clockwise R

counter-clockwise L

Seals 10 to �00 �50 to 1000

09NBR (nitril-caoutchouc) – P

FKM (fluor-caoutchouc) V

Shaft end 10 1� 16 �3 �8 3� 45 56 63 80 90 107 1�5 160 180 �00 �50 355 500 710 1000

10

Splined shaft DIN 5480

– – – – – – A

– – – – – – – Z

Parallel keyed shaft, DIN 6885

– – – – – – B

– – – – – – – P

Mounting flange 10 to �50 355 to 1000

114-hole – ISO 3019-2 – B

8-hole – ISO 3019-2 – H

Service line ports 1) 10 to 16 �3 to �50 355 to 1000

12

SAE flange ports A and B, at side and SAE flange port S, rear – – 05

Threaded ports A and B, at side and SAE flange port S, rear – – 06

SAE flange ports A and B, rear and SAE flange port S, rear – – 11

1) Fastening threads resp. threaded ports are metric

= available – = not available

= preferred program

A�F O / 6 –01 02 03 04 05 06 07 08 09 10 11 12

Ordering Code / Standard Program (ordering code size 5 see page 8)

Page 3: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 3/24

Hydraulic fluidBefore starting project planning, please refer to our data sheets RE 90220 (mineral oil), RE 90221 (environmentally acceptable hydraulic fluids) and RE 90223 (HF hydraulic fluids) for detailed information regarding the choice of hydraulic fluid and applica-tion conditions.

The fixed pump A2FO is unsuitable for operation with HFA. If HFB, HFC and HFD or environmentally acceptable hydraulic flu-ids are being used, the limitations regarding technical data and seals mentioned in RE 90221 and RE 90223 must be observed.

When ordering, please indicate the used hydraulic fluid.

Operating viscosity range

For optimum efficiency and service life, select an operating vis-cosity (at operating temperature) within the optimum range of

νopt = optimum operating viscosity 16 to 36 mm2/s

depending on the tank temperature (closed circuit) and tank temperature (open circuit).

Limits of viscosity range

The limiting values for viscosity are as follows:

Sizes 5 to 200:

νmin = 5 mm2/s, short-term (t < 3 min) at max. perm. temperature of tmax = +115°C.

νmax = 1600 mm2/s, short-term (t < 3 min) at cold start (p ≤ 30 bar, n ≤ 1000 rpm, tmin = -40°C) Only for starting up without load. Optimum operating viscosity must be reached within approx. 15 minutes.

Sizes 250 to 1000:

νmin = 10 mm2/s, short-term (t < 3 min) at max. perm. temperature of tmax = +90°C.

νmax = 1000 mm2/s, short-term (t < 3 min) at cold start (p ≤ 30 bar, n ≤ 1000 rpm, tmin = -25°C). Only for starting up without load. Optimum operating viscosity must be reached within approx. 15 minutes.

Note that the maximum hydraulic fluid temperature of 115°C (90°C at size 250 to 1000) must not be exceeded locally either (e.g. in the bearing area). The temperature in the bearing area is - depending on pressure and speed - up to 12 K higher than the average case drain temperature.

Special measures are necessary in the temperature range from -40°C and -25°C (cold start phase), please contact us.

For detailed information about use at low temperatures, see RE 90300-03-B.

Technical DataSelection diagram

tmin = -40°C tmax = +115°C

-40° -25° -10° 10° 30° 50° 90° 115°70°0°5

10

4060

20

100

200

400600

10001600

-40° 0° 20° 40° 60° 80° 100° -20°1600

νopt.

16

36VG

22VG

32VG

46VG

68VG

100

5

Hydraulic fluid temperature range

Temperature t in °C

Visc

osity

ν in

mm

2 /s

Details regarding the choice of hydraulic fluid

The correct choice of hydraulic fluid requires knowledge of the operating temperature in relation to the ambient temperature: in an open circuit the tank temperature.

The hydraulic fluid should be chosen so that the operating vis-cosity in the operating temperature range is within the optimum range (νopt.) - the shaded area of the selection diagram. We recommended that the higher viscosity class be selected in each case.

Example: At an ambient temperature of X°C an operating temperature of 60°C is set. In the optimum operating viscosity range (νopt; shaded area) this corresponds to the viscosity classes VG 46 or VG 68; to be selected: VG 68.

Please note: The case drain temperature, which is affected by pressure and speed, is always higher than the tank temperature. At no point in the system may the temperature be higher than 115°C for sizes 5 to 200 or 90°C for sizes 250 to 1000.

If the above conditions cannot be maintained due to extreme operating parameters, we recommend flushing the case at port U (size 250 to 1000).

FiltrationThe finer the filtration, the higher the cleanliness level of the hy-draulic fluid and the longer the service life of the axial piston unit.

To ensure functional reliability of the axial piston unit, the hy-draulic fluid must have a cleanliness level of at least

20/18/15 according to ISO 4406.

At very high hydraulic fluid temperatures (90°C to max. 115°C, not permitted for sizes 250 to 1000) at least cleanliness level

19/17/14 according to ISO 4406 is required.

If the above classes cannot be observed, please contact us.

Page 4: BOSCH REXROTH Axial Piston Fixed Pump a2fo

4/24 Bosch Rexroth AG A�FO RE 91401/03.08

Technical DataOperational pressure range

Inlet

Pressure at port S The minimum inlet pressure depends on speed. The following limits must not be exceeded.

pabs min _________________________________________ 0,8 bar

pabs max _________________________________________ 30 bar

Minimum inlet pressure at suction port S with increased speed

In order to avoid damage of the pump a minimum inlet pressure at the suction port must be assured. The minimum inlet pressu-re is related to the rotational speed of the fixed pump.

2,01,81,61,41,21,00,80

1

2

3

4

sizes 5 to 200

Speed n/nmax

sizes 250 to 1000

Inle

t pre

ssur

e p a

bs. i

n ba

r

Note:

– max. permissible speed nmax perm. (speed limit)

– min. permissible inlet pressure at port S

– admissible values for the drive shaft seal

Outlet

Maximum pressure on port A or B (pressure data according to DIN 24312)

Size 5 Shaft end B Shaft end C

Nominal pressure pN 210 bar 315 bar

Peak pressure pmax 250 bar 350 bar

Sizes 10 to �00 Shaft end A, Z 1) Shaft end B, P

Nominal pressure pN 400 bar 350 bar

Peak pressure pmax 450 bar 400 bar

Sizes �50 to 1000

Nominal pressure pN 350 bar

Peak pressure pmax 400 bar

1) size 56 with shaft end Z: pN = 350 bar, pmax = 400 bar

Please note: Sizes 10 to 200: With shaft end Z and P, a nominal pressure of pN = 315 bar (pmax = 350 bar) is permissible for drives with radial loading of the drive shaft (pinions, V-belts)! Sizes 250 to 1000: Please contact us.

In cases of pulsating loading above 315 bar, we recommend the version with splined shaft A (sizes 10 to 200) or with splined shaft Z (sizes 45, 250 to 1000).

Direction of flow

Direction of rotation, viewed on shaft endclockwise counter-clockwiseS to B S to A

Long-life bearing (sizes �50 to 1000)For long service life and use with HF hydraulic fluids. Same external dimensions as pump with standard bearing. A long-life bearing can be specified. Flushing of bearing and case via port U recommended.

Flushing volumes (recommended)

Size �50 355 500 710 1000

qv flush (L/min) 10 16 16 16 16

Symbol

Connections

A, B Service line port S Suction port T1, T2 Drain ports R/U Port for bearing flushing

B (A)

S

T1

T2R / U

Page 5: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 5/24

Shaft seal ring

Permissible pressure loading for shaft seal ring FKM

The service life of the shaft seal ring is affected by the speed of the pump and the case drain pressure. It is recommended that the average, continuous case drain pressure at operating tem-perature 3 bar absolute not be exceeded (max. permissible case drain pressure 6 bar absolute at reduced speed, see diagram). Short term (t < 0.1 s) pressure spikes of up to 10 bar absolute are permitted. The service life of the shaft seal ring decreases with an increase in the frequency of pressure spikes.

The case pressure must be equal to or greater than the exter-nal pressure on the shaft seal ring.

Sizes 10 to 200

7000 80005000 600040002000 30000 10001

2

3

4

5

6

7

8

9

10

Speed n (rpm)

Per

m. p

ress

ure

p abs

. max

. (ba

r) sizes 10, 12, 16

sizes 23, 28, 32

size 45

sizes 56, 63

sizes 80, 90

size 200

sizes 107, 125

sizes 160, 180

Sizes 250 to 1000

3

2

10 1000 2000500 1500 2500

4

5

6

Per

m. p

ress

ure

p abs

. max

. (ba

r)

Speed n (rpm)

size 710, 1000

size 500

size 250

size 355

Permissible pressure loading for shaft seal ring NBR sizes 5...200

For shaft seal rings of NBR 33% reduced values for the max. permissible case pressure pabs.max. are to be considered com-pared with seals of FKM.

Technical DataTemperature range

The FKM shaft seal ring is permissible for case temperatures of -25°C to +115°C at sizes 5 to 200 and -25°C to +90°C at sizes 250 to 1000

Note: For application cases below -25°C, an NBR shaft seal ring is necessary (permissible temperature range: -40°C to +90°C.) Please contact us.

Page 6: BOSCH REXROTH Axial Piston Fixed Pump a2fo

6/24 Bosch Rexroth AG A�FO RE 91401/03.08

Technical DataTable of values (theoretical values, without efficiency and tolerances; values rounded)

Size 5 10 1� 16 �3 �8 3� 45 56 63 80Displacement Vg cm3 4,93 10,3 12 16 22,9 28,1 32 45,6 56,1 63 80,4Max. speed nmax

1) rpm 5600 3150 3150 3150 2500 2500 2500 2240 2000 2000 1800nmax limit

2) rpm 8000 6000 6000 6000 4750 4750 4750 4250 3750 3750 3350Max. flow at nmax qV max L/min 27,6 32,4 37,8 50 57 70 80 102 112 126 144Power at Δp = 350 bar Pmax kW 14,53) 18,9 22 29,2 33 41 47 59,5 65 73,5 84

Δp = 400 bar Pmax kW – 21,6 25 34 38 47 53 68 75 84 96Torque at Δp = 350 bar T Nm 24,73) 57 67 88 126 156 178 254 312 350 445

Δp = 400 bar T Nm – 65 76 101 145 178 203 290 356 400 511Rotary stiffness c Nm/rad 625 922 1250 1590 2560 2930 3120 4180 5940 6250 8730

Moment of inertia -for rotary group

JTW kgm2 0,00006 0,0004 0,0004 0,0004 0,0012 0,0012 0,0012 0,0024 0,0042 0,0042 0,0072

Angular acceleration max. a rad/s2 5000 5000 5000 5000 6500 6500 6500 14600 7500 7500 6000Filling capacity V L 0,17 0,17 0,17 0,20 0,20 0,20 0,33 0,45 0,45 0,55Mass (approx.) m kg 2,5 6 6 6 9,5 9,5 9,5 13,5 18 18 23

Size 90 107 1�5 160 180 �00 �50 355 500 710 1000Displacement Vg cm3 90 106,7 125 160,4 180 200 250 355 500 710 1000Max. speed nmax

1) rpm 1800 1600 1600 1450 1450 1550 1500 1320 1200 1200 950nmax limit

2) rpm 3350 3000 3000 2650 2650 2750 1800 1600 1500 1500 1200Max. flow at nmax qV max L/min 162 170 200 232 261 310 375 469 600 826 950

Power at Δp = 350 bar Pmax kW 95 100 117 135 152 181 219 273 350 497 554Δp = 400 bar Pmax kW 108 114 133 155 174 207 – – – – –

Torque at Δp = 350 bar T Nm 501 594 696 893 1003 1114 1393 1978 2785 3955 5570Δp = 400 bar T Nm 572 678 795 1020 1145 1272 – – – – –

Rotary stiffness c Nm/rad 9140 11200 11900 17400 18200 57300 73100 96100 144000 270000 324000

Moment of inertia -for rotary group

JTW kgm2 0,0072 0,0116 0,0116 0,0220 0,0220 0,0353 0,061 0,102 0,178 0,55 0,55

Angular acceleration max. a rad/s2 6000 4500 4500 3500 3500 11000 10000 8300 5500 4300 4000

Filling capacity V L 0,55 0,8 0,8 1,1 1,1 2,7 2,5 3,5 4,2 8 8Mass (approx.) m kg 23 32 32 45 45 66 73 110 155 325 3361) The values shown are valid for an absolute pressure (pabs) of 1 bar at the suction inlet S and when operated on mineral oil (with

a specific mass of 0,88 kg/L).2) By increase of the input pressure (pabs > 1 bar) the rotational speeds can be increased to the max. admissible speeds nmax limit

(speed limits) (see diagram page 4).3) Torque at Δp = 315 bar

Caution: Exceeding the permissible limit values may result in a loss of function, a reduction in service life or in the destruction of the axial piston unit. Other permissible limit values with respect to speed variation, reduced angular accelaration as a function of the frequency and the permissible startup angular acceleration (lower than the maximum angular acceleration) can be found in data sheet RE 90261.

Determining the size

Flow qv =Vg • n • ηv

L/min1000

Torque T =Vg • Δp

Nm20 • π • ηmh

Power P =2 π • T • n

=qv • Δp

kW60000 600 • ηt

Vg = Displacement per revolution in cm3

Δp = Differential pressure in bar

n = Speed in rpm

ηv = Volumetric efficiency

ηmh = Mechanical-hydraulic efficiency

ηt = Overall efficiency

Page 7: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 7/24

Technical DataPermissible radial and axial loading on the drive shaftThe specified values given are maximum values and do not apply to continuous operation.

Size 5 10 1� 16 �3 �8 3� 45 56 63 80

Radial force, max. 1) at distance a (from shaft collar) a

Fq Fq max N 710 2350 2750 3700 4300 5400 6100 81502) 92002)10300 115002)

a mm 12 16 16 16 16 16 16 18 18 18 20

Axial force, max. 3) –

+Fax

+Fax max N 180 320 320 320 500 500 500 630 800 800 1000

–Fax max N 180 320 320 320 500 500 500 630 800 800 1000

Permissible axial force/bar operating pressure

±Fax per./bar N/bar 1,5 3,0 3,0 3,0 5,2 5,2 5,2 7,0 8,7 8,7 10,6

Size 90 107 1�5 160 180 �00 �50 355 500 710 1000

Radial force, max. 1) at distance a (from shaft collar) a

Fq Fq max N 1290013600 15900 18400 20600 22900 12004) 15004) 19004) 30004)26004)

a mm 20 20 20 25 25 25 41 52,5 52,5 67,5 67,5

Axial force, max. 3) –

+Fax

+Fax max N 1000 1250 1250 1600 1600 1600 2000 2500 3000 4400 4400

–Fax max N 1000 1250 1250 1600 1600 1600 2000 2500 3000 4400 4400

Permissible axial force/bar operating pressure

±Fax per./bar N/bar 10,6 12,9 12,9 16,7 16,7 16,7 5) 5) 5) 5) 5)

1) During intermittent operation (sizes 5 to 200) 2) Permissible max. radial force with shaft end Z: Fq max = 6500 N 3) Max. permissible axial force when at a standstill or when axial piston unit working in pressureless conditions 4) When at a standstill or when axial piston unit operating in depressurized condition. Higher forces are permissible when under pressure. Please contact us. 5) Please contact us

When considering the permissible axial force, the force-transfer direction must be taken into account:

– Fax max = increase in service life of bearings

+ Fax max = reduction in service life of bearings (avoid)

Effect of radial force Fq on the service life of the bearings

By selecting a suitable force-transfer direction of Fq, the stress on the bearing caused by the internal transmission forces can be reduced, thus achieving the optimum service life for the bearings. Recommended position of mating gear is dependent on direction of rotation. Examples:

Toothed gear drive V-belt drive

Size ϕopt. ϕopt.

10 to 180 ± 70° ± 45°

200 to 1000 ± 45° ± 70°

ϕ opt. ϕopt.

ϕ opt. ϕopt.

Clockwise direction of rotation

Pressure on port B

Clockwise direction of rotation

Pressure on port B

Counter-clockwise direction of rotation

Pressure on port A

Page 8: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Clockwise rotationcounter-clockwise rotation: port plate is rotated through 180°

8/24 Bosch Rexroth AG A�FO RE 91401/03.08

Unit Dimensions, Size 5

Shaft ends

B Parallel keyed shaft, DIN 6885, A4x4x20 pN = 210 bar

C Tapered shaft with spigot and spring washer 3x5 DIN 6888, pN = 315 bar (taper 1:10)

Ports

B (A) Service line port DIN 3852

M18x1,5; 12 deep 140 Nm 3)

S Suction port DIN 3852

M22x1,5; 14 deep 210 Nm 3)

T1, T2 Case drain ports DIN 3852

M10x1; 8 deep 30 Nm 3)

1) Center bore according to DIN 332 (thread according to DIN 13)

2) Thread according to DIN 3852, max. tightening torque: 30 Nm3) Please observe the general notes for the max. tightening

torques on page 24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.

Ordering Code / Standard Program – Size 5

Additional instructions in text form

Seals

The fixed pump A2F5 is equipped with NBR- (nitril-caoutchouc) seals in standard design.

In case of need FKM- (fluor-caoutchouc) seals please indicate when ordering in plain text:

“with FKM-seals”

Axial piston unit01 Bent axis design, fixed A�F

Size02 ≈ Displacement Vg max (cm3) 5

Series03 60

Direction of rotation

04Viewed from shaft end clockwise R

counter-clockwise L

Shaft end

05Parallel keyed shaft DIN 6885 B

Tapered shaft with spigot and spring washer DIN 6888 C

Service line ports06 Threads A and B at side, metric 7

A�F 5 / 60 – 701 02 03 04 05 06

10

3.2

24

13.5

R0.4

ø15

ø12

+0.0

01+0

.012

M4x

0.7

1 ) 3 )

4

33

22

7.3

ø12.

8

M10

x1 2 )

3 )

ø15

Y

B (A)T1, T2

451

108

24

25°

8468

52

ø60

-0.0

46 B (A) S

6045° 45°

ø75 0

.1

706.

4

70

5128

7.4

Detail Y

Page 9: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 9/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Sizes 10, 12, 16

Shaft ends

Sizes 10, 1�, 16 Sizes 10, 1� Sizes 10, 1�, 16 Sizes 10, 1�

A Splined shaft DIN 5480 W25x1,25x30x18x9g pN = 400 bar

Z Splined shaft DIN 5480 W20x1,25x30x14x9g pN = 400 bar

B Parallel keyed shaft DIN 6885, AS8x7x32 pN = 350 bar

P Parallel keyed shaft DIN 6885, A6x6x32 pN = 350 bar

Ports

B (A) Service line port DIN 3852 M22x1,5; 14 deep 210 Nm 2)

S Suction port DIN 3852 M33x2; 18 deep 540 Nm 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M12x1,5; 12 deep 50 Nm 2)

R Air bleed (plugged) DIN 3852 M8x1; 8 deep 10 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

22

7.5

6

28

M10

x1.5

1 ) 2 )

ø28

16

5

12

34

M6x

1 1 )

2 )

ø28

22

7.5

40

E1x0.2DIN 509

28

M10

x1.5

1 ) 2 )

ø25

+0.0

15+0

.002

ø28

16

5

40

E1x0.2DIN 509

22.5

M6x

1 1 )

2 )

ø20+

0.01

5+

0.00

2

ø28

48

40

42.5 16

45 45

ø9

95

95

ø100

2418.260

ø80

-0.0

19

6

54

20

2956

94

69

131

147

167

1295

85

T1

RT2

Y

B (A)S

Flange similar to ISO 3019-2 Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 10: BOSCH REXROTH Axial Piston Fixed Pump a2fo

10/24 Bosch Rexroth AG A�FO RE 91401/03.08

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.

Shaft ends

Sizes �3, �8, 3� Sizes �3, �8 Sizes �3, �8, 3� Sizes �3, �8

A Splined shaft DIN 5480 W30x2x30x14x9g pN = 400 bar

Z Splined shaft DIN 5480 W25x1,25x30x18x9g pN = 400 bar

B Parallel keyed shaft DIN 6885, AS8x7x40 pN = 350 bar

P Parallel keyed shaft DIN 6885, AS8x7x40 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1/2 in – Fastening threads B/A DIN13 M8x1,25; 15 deep 2)

S Suction port (standard pressure series) SAE J518 3/4 in – Fastening thread S DIN13 M10x1,5; 17 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M16x1,5; 14 deep 100 Nm 2)

R Air bleed (plugged) DIN 3852 M10x1; 12 deep 30 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

Unit Dimensions, Sizes 23, 28, 32

22

35

7.5

8

M10

x1.5

1 ) 2 )

ø35

33

E1x0.2DIN 509

22

7.5

50

M10

x1.5

1 ) 2 )

ø30

+0.0

15+0

.002

ø35 28

19

6

50

E1x0.2DIN 509

M8x

1.25

1 ) 2 )

ø25

+0.0

15+0

.002

ø35

6

19

15

43

M8x

1.25

1 ) 2 )

ø35

118

60 14

120

40°

ø11 11

8

ø125

ø100

-0.0

22

2570

91

22.2

42923.2

56

825

106

144169

193 SB (A)

61

Y

T1

T2R

45°45°18

40.5

ø13

106

47.6ø19

18.2

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 11: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 11/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Size 45

Shaft ends

Z Splined shaft DIN 5480 W30x2x30x14x9g pN = 400 bar

P Parallel keyed shaft DIN 6885, AS8x7x50 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 3/4 in – Fastening threads B/A DIN13 M10x1,5; 17 deep 2)

S Suction port (standard pressure series) SAE J518 1 in – Fastening threads S DIN13 M10x1,5; 17 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M18x1,5; 14 deep 140 Nm 2)

R Air bleed (plugged) DIN 3852 M12x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

M12

x1.7

5 1 )

2 )

28

9.5

8

35

ø35

9.528

33

60

E1x0.2DIN 509

ø30

+0.0

15+0

.002

ø35

M12

x1.7

5 1 )

2 )

64 2052.4

26.2

118

ø25

42

28

1130

206

50.8

ø19

132

ø160

ø13.

5

45° 45°

150

150

10280

23.8

155

108ø1

25 -0

.025

32 2060.3

181

12

B (A)

S

R T2

Y

6378T1

40°

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 12: BOSCH REXROTH Axial Piston Fixed Pump a2fo

1�/24 Bosch Rexroth AG A�FO RE 91401/03.08

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Sizes 56, 63

Shaft ends

Sizes 56, 63 Size 56 Sizes 56, 63 Size 56

A Splined shaft DIN 5480 W35x2x30x16x9g pN = 400 bar

Z Splined shaft DIN 5480 W30x2x30x14x9g pN = 350 bar

B Parallel keyed shaft DIN 6885, AS10x8x50 pN = 350 bar

P Parallel keyed shaft DIN 6885, AS8x7x50 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 3/4 in – Fastening threads B/A DIN13 M10x1,5; 17 deep 2)

S Suction port (standard pressure series) SAE J518 1 in – Fastening thread S DIN13 M10x1,5; 17 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M18x1,5; 14 deep 140 Nm 2)

R Air bleed (plugged) DIN 3852 M12x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

28

9.5

8

40

M12

x1.7

5 1 )

2 )

ø40

289.5

60

E1x0.2DIN 509

M12

x1.7

5 1 )

2 )

38ø3

5+0

.018

+0.0

02

ø40

28

9.5

60

E1x0.2DIN 509

M12

x1.7

5 1 )

2 )

33ø3

0+0

.015

+0.0

02

ø40

28

9.5

8

35

M12

x1.7

5 1 )

2 )

ø40

68 23

26.2

128

52.4

25

107

19514

2225

171

40° 23.8

ø1950

.878

5031

117

1130

ø160

ø13.

5 150

150

45° 45°

70 87

20

10

32

ø125

-0.0

25

SB (A)

R T2

Y

T1

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 13: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 13/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Sizes 80, 90

Shaft ends

Sizes 80, 90 Size 80 Sizes 80, 90 Size 80

A Splined shaft DIN 5480 W40x2x30x18x9g pN = 400 bar

Z Splined shaft DIN 5480 W35x2x30x16x9g pN = 400 bar

B Parallel keyed shaft DIN 6885, AS12x8x56 pN = 350 bar

P Parallel keyed shaft DIN 6885, AS10x8x56 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 in – Fastening threads B/A DIN13 M12x1,5; 17 deep 2)

S Suction port (standard pressure series) SAE J518 1 1/4 in – Fastening thread S DIN13 M10x1,5; 17 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M18x1,5; 14 deep 140 Nm 2)

R Air bleed (plugged) DIN 3852 M12x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

28

9.5

M12

x1.7

5 1 )

2 )

8

40

ø45

36

12

M16

x2 1 )

2 )

8

45

ø45

ø45

E1x0.2DIN 509

36

12

70

43

M16

x2 1 )

2 )

ø40

+0.0

18+0

.002

28

9.5

70

38

M12

x1.7

5 1 )

2 )

E1x0.2DIN 509

ø35

+0.0

18+0

.002

ø45

78.5

40°

138

25

58.7ø32

30.2

73

ø13.

5

45°

ø180

9941

27.883

129 164

ø140

-0.0

25

32132

196

254224

122

158

1020

86

ø2557

.2

165

165

45°

Y

T2R

B (A)S

T1

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 14: BOSCH REXROTH Axial Piston Fixed Pump a2fo

14/24 Bosch Rexroth AG A�FO RE 91401/03.08

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Sizes 107, 125

Shaft ends

Sizes 107, 1�5 Size 107 Sizes 107, 1�5 Size 107

A Splined shaft DIN 5480 W45x2x30x21x9g pN = 400 bar

Z Splined shaft DIN 5480 W40x2x30x18x9g pN = 400 bar

B Parallel keyed shaft DIN 6885, AS14x9x63 pN = 350 bar

P Parallel keyed shaft DIN 6885, AS12x8x63 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 in (size 107) – SAE J518 1 1/4 in (size 125) – Fastening threads B/A DIN13 M12x1,75; 17 deep (size 107) 2) DIN13 M14x2; 19 deep (size 125) 2)

S Suction port (standard pressure series) SAE J518 1 1/2 in – Fastening thread S DIN13 M12x1,75; 20 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M18x1,5; 14 deep 140 Nm 2)

R Air bleed ( plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

36

12

ø50

8

50

M16

x2 1 )

2 ) 36

12

80

ø50

M16

x2 1 )

2 )

48.5

E1x0.2DIN 509

ø45+0

.018

+0.0

02

28

9.5

80

ø5043

M12

x1.7

5 1 )

2)

E1x0.2DIN 509

ø40

+0.0

18+0

.00228

9.5

8

45

ø50

M12

x1.7

5 1 )

2)

1236.5

40

4545

69.9

89 20

35.7

38 150

190

190

ø17.

5

ø200

4011

013

617

4

65

ø160

-0.0

25

1040

140

213245

275

23

98

SB (A)

Y

T2R

85T2

31.8(27.8)

32(2

5)

66.7

(57.

2)

Flange ISO 3019-2 Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°(dimensions for size 107 in bracket)

Detail port A/B

Page 15: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 15/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Sizes 160, 180

Shaft ends

Sizes 160, 180 Size 160 Sizes 160, 180 Size 160

A Splined shaft DIN 5480 W50x2x30x24x9g pN = 400 bar

Z Splined shaft DIN 5480 W45x2x30x21x9g pN = 400 bar

B Parallel keyed shaft DIN 6885, AS14x9x70 pN = 350 bar

P Parallel keyed shaft DIN 6885, AS14x9x70 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 1/4 in – Fastening threads B/A DIN13 M14x2; 19 deep 2)

S Suction port (standard pressure series) SAE J518 1 1/2 in – Fastening thread S DIN13 M12x1,75; 20 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M22x1,5; 14 deep 210 Nm 2)

R Air bleed (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

36

12

11

55

ø60

M16

x2 1 )

2 )

36

12

90

53.5

ø60

M16

x2 1 )

2 )

R1.6

ø50

+0.0

18+0

.00236

12

8

50

ø60

M16

x2 1 )

2 )

36

12

90

48.5

ø60

M16

x2 1 )

2 )

R1.6

ø45

+0.0

18+0

.002

149

42 180

35.7

69.9

15101

ø17.5 ø224

45°45°

210

210

96

108

121

31.8

ø3266

.7

137.2 372

ø180

-0.0

25

251040

158

237271

294

40°

B (A)S

47

188

T2R

Y

T1

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 16: BOSCH REXROTH Axial Piston Fixed Pump a2fo

16/24 Bosch Rexroth AG A�FO RE 91401/03.08

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.

Shaft ends

A Splined shaft DIN 5480 W50x2x30x24x9g pN = 400 bar

B Parallel keyed shaft DIN 6885, AS14x9x80 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 1/4 in – Fastening threads B/A DIN13 M14x2; 19 deep 2)

S Suction port (standard pressure series) SAE J518 3 1/2 in – Fastening thread S DIN13 M16x2; 24 deep 2)

T1, T2 Case drain ports (T1 plugged) DIN 3852 M22x1,5; 14 deep 210 Nm 2)

R Air bleed (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Centering bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

Unit Dimensions, Size 200

36

12

11

55

ø70

M16

x2 1 )

2 )

36

12

100

53.5

ø70

R1.6

M16

x2 1 )

2 )

ø50

+0.0

18+0

.002

77

157

69.9

120.

7

66.7

31.8

121

90 211

108

25

75

169

100

329

265319

351

891632

40

102.

5ø200

-0.0

29

ø250

ø32

236

45

236

ø22

45

T2R Y

S

T1

B (A)

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 17: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 17/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Size 250

Shaft ends

Z Splined shaft DIN 5480 W50x2x30x24x9g pN = 350 bar

P Parallel keyed shaft DIN 6885, AS14x9x80 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 1/4 in – Fastening threads B/A DIN13 M14x2; 19 deep 2)

S Suction port (standard pressure series) SAE J518 2 1/2 in – Fastening thread S DIN13 M12x1,75; 17 deep 2)

T1, T2 Case drain ports (T2 plugged) DIN 3852 M22x1,5; 14 deep 210 Nm 2)

U Port for bearing flushing (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Centering bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

36

12

82R1.6

53.5

ø60

M16

x2 1 )

2 )

ø50

+0.0

18+0

.00236

12

9

58

ø60

M16

x2 1 )

2 )

124

ø280

246

45° 45°

267

82

50

2248

ø22

9 2582

309

105

105 82

10326

°30´

66.7ø3

2

T2

U

210

B (A)

ø63

118

88.912

S

31.8

172

329

ø250

30°

M16

50.8

ø224

-0.0

29

T1

246

Y

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 18: BOSCH REXROTH Axial Piston Fixed Pump a2fo

18/24 Bosch Rexroth AG A�FO RE 91401/03.08

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Size 355

Shaft ends

Z Splined shaft DIN 5480 W60x2x30x28x9g pN = 350 bar

P Parallel keyed shaft DIN 6885, AS18x11x100 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 1/2 in – Fastening threads B/A DIN13 M16x2; 21 deep 2)

S Suction port (standard pressure series) SAE J518 2 1/2 in – Fastening thread S DIN13 M12x1,75; 17 deep 2)

T1, T2 Case drain ports (T2 plugged) DIN 3852 M33x2; 18 deep 540 Nm 2)

U Port for bearing flushing (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

MA, MB Gauge ports operating pressure A, B (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

MS Gauge port suction pressure (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

42

15

11

82

M20

x2.5

1 ) 2 )

ø70

42

15

105

64 ø70

M20

x2.5

1 ) 2 )

ø60

+0.0

30+0

.011

R1.6

ø63

245

88.9

50.8

36.5

250

ø40

79.4

60 50

50

45°

26°30'

23.548

ø320

ø360

335

M18

335

171

22°30'83

128

102

19812

8

320350

14 2883

ø280

-0.0

81

ø18

B (A)

8x45°UT1

T2Y

(=360°)

S

MB (MA) MS

Detail YFlange ISO 3019-2

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 19: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO 19/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.

Shaft ends

Z Splined shaft DIN 5480 W70x3x30x22x9g pN = 350 bar

P Parallel keyed shaft DIN 6885, AS20x12x100 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 1 1/2 in – Fastening threads B/A DIN13 M16x2; 24 deep 2)

S Suction port (standard pressure series) SAE J518 3 in – Fastening thread S DIN13 M16x2; 24 deep 2)

T1, T2 Case drain ports (T2 plugged) DIN 3852 M33x2; 18 deep 540 Nm 2)

U Port for bearing flushing (plugged) DIN 3852 M18x1,5; 12 deep 140 Nm 2)

MA, MB Gauge ports operating pressure A, B (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

MS Gauge port suction pressure (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

Unit Dimensions, Size 500

42

15

13

80

ø80M

20x2

.5 1 )

2 )

ø80

42

15

105

74.5

M20

x2.5

1 ) 2 )

ø70

+0.0

30+0

.011

R1.6

106.455

ø75

62

192

48 27.598

142

220

396

112.

5

26°30

'

30111

362

ø360ø400

375

375

M20

ø22

22°30'34°

ø40

79.4

270

36.6

27665

5014

ø315

-0.0

81U T1

T2

8x45°

SB (A)

Y

(=360°)

MB (MA) MS

142

Detail YFlange ISO 3019-2

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 20: BOSCH REXROTH Axial Piston Fixed Pump a2fo

�0/24 Bosch Rexroth AG A�FO RE 91401/03.08

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Size 710

Shaft ends

Z Splined shaft DIN 5480 W90x3x30x28x9g pN = 350 bar

P Parallel keyed shaft DIN 6885, AS25x14x125 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 2 in – Fastening threads B/A DIN13 M20x2,5; 30 deep 2)

S Suction port (standard pressure series) SAE J518 4 in – Fastening thread S DIN13 M16x2; 24 deep 2)

T1, T2 Case drain ports (T2 plugged) DIN 3852 M42x2; 20 deep 720 Nm 2)

U Port for bearing flushing (plugged) DIN 3852 M18x1,5; 12 deep 140 Nm 2)

MA, MB Gauge ports operating pressure A, B (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

MS Gauge port suction pressure (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

50

18

14

105

ø100

M24

x3 1 )

2 ) 50

18

130

95 ø100

M24

x3 1 )

2 )

ø90

+0.0

35+0

.013

R1.6

465

ø22

236

465

ø500

ø450

15635

252

T2

U

50710

2

183

183

ø400

-0.0

89

T1

14

41.547

50

131

486

18°3

44.585 70

130.2

SB (A)

77.8

340

ø50

344

MB (MA)

M24

Y

45° 22°30' 8x45°(=360°)

96.8

ø100

MS

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 21: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO �1/24

Before finalizing your design, please request a binding installation drawing. Dimensions in mm.Unit Dimensions, Size 1000

Shaft ends

Z Splined shaft DIN 5480 W90x3x30x28x9g pN = 350 bar

P Parallel keyed shaft DIN 6885, AS25x14x125 pN = 350 bar

Ports B (A) Service line port (high pressure series) SAE J518 2 in – Fastening threads B/A DIN13 M20x2,5; 30 deep 2)

S Suction port (standard pressure series) SAE J518 4 in – Fastening thread S DIN13 M16x2; 24 deep 2)

T1, T2 Case drain ports (T2 plugged) DIN 3852 M42x2; 20 deep 720 Nm 2)

U Port for bearing flushing (plugged) DIN 3852 M18x1,5; 12 deep 140 Nm 2)

MA, MB Gauge ports operating pressure A, B (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

MS Gauge port suction pressure (plugged) DIN 3852 M14x1,5; 12 deep 80 Nm 2)

1) Center bore according to DIN 332 (thread according to DIN 13) 2) Please observe the general notes for the max. tightening torques on page 24

50

18

14

105

ø100

M24

x3 1 )

2 ) 50

18

130

95 ø100

M24

x3 1 )

2 )

ø90

+0.0

35+0

.013

R1.6

1450

130.2

77.8

ø100

ø400

-0.0

89

143

277

511

26°30'

45° 22°30'

465

465

ø50

96.8

340

85344

44.5

183

183

35156

41.547131

468

236

ø500

ø450

M24

8x45°

T2

U T1

ø22

(=360°)

Y

70

SB (A)

MB (MA) MS

Flange ISO 3019-2

Detail Y

Clockwise rotationCounter-clockwise rotation: port plate is rotated through 180°

Page 22: BOSCH REXROTH Axial Piston Fixed Pump a2fo

��/24 Bosch Rexroth AG A�FO RE 91401/03.08

Installation below the tank

Pump below min. fluid level in the tank (standard)

– Fill axial piston pump before startup via the highest case drain port

– Run the pump at low speed until the system is bled completely.

– Minimum immersion depth of leakage line in tank: 200 mm (relative to the min. fluid level in the tank).

– Additional measures required for installation position 2 (shaft facing up): with installation position 2, make sure that the pump case is completely full before starting up. Bleed at port R (sizes 10 to 200) resp. U (sizes 250 to 1000). An air pocket in the bearing area is leading to damage of the axial piston pump.

– Recommendation: Fill up suction lines

T2

T2

R (U)

T1

T1

S

S

S

S

*

Installation position 2

Installation notesGeneral

The pump case must be completely filled up with hydraulic fluid during startup and during operation (filling the case chamber). The pump must be started up at low speed and no load until the system has been bled completely.

If stopped for an extended period, fluid may drain out of the case through the service lines. When restarting, make sure that the case contains sufficient fluid.

The leakage fluid inside the case chamber must be drained off to the tank through the highest case drain port. The min. suction pressure at port S must not fall below 0,8 bar absolute (see page 4).

Installation position

Optional.

Installation above the tank

Pump above minimum fluid level in tank

– Proceed in same way as below the tank installation

– Additional measures for installation positions 1 and 2: If stopped for an extended period, fluid may drain out of the case chamber through the service lines (air enters through the shaft seal). The bearings will therefore not be properly lubricated when the pump is started up again. Fill the axial piston pump before restarting via the highest case drain port. Installation position 2: bleed at port R (sizes 10 to 200) resp. U (sizes 250 to 1000).

– Additional measures required for installation position 2 (shaft facing up): In this installation position the bearings will not be properly lubricated, even if there is still some fluid in the case cham-ber. Putting a non-return valve (opening pressure 0,5 bar) in the leakage line can prevent the system emptying through the line.

– Note: min. admissible pressure at port S (min. suction pres-sure see page 5)

T2

R (U)

T1

T1

S

S

S

S

0,5

bar

* *

T2

Installation position 2

Installation position 1

Page 23: BOSCH REXROTH Axial Piston Fixed Pump a2fo

Bosch Rexroth AGRE 91401/03.08 A�FO �3/24

Notes

Page 24: BOSCH REXROTH Axial Piston Fixed Pump a2fo

�4/24 Bosch Rexroth AG A�FO RE 91401/03.08

© This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent.

The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.

Subject to change.

Bosch Rexroth AG HydraulicsProduct Segment Axial Piston UnitsElchingen Plant Glockeraustrasse 2 89275 Elchingen, Germany Phone +49 (0) 73 08 82-0 Facsimile +49 (0) 73 08 72 [email protected] www.boschrexroth.com/axial-piston-pumps

Horb PlantAn den Kelterwiesen 14 72160 Horb, Germany Phone +49 (0) 74 51 92-0 Facsimile +49 (0) 74 51 82 21

General Notes– The A2FO pump is designed to be used in open circuits.

– Project planning, assembly, and commissioning of the pump require the involvement of qualified personnel.

– The service line ports and function ports are only designed to accommodate hydraulic lines.

– During and shortly after operation, there is a risk of burns on the pump. Take suitable safety precautions, e.g. wear protective clothing

– There may be shifts in the characteristic depending on the operating state of the pump (operating pressure, fluid temperature).

– Tightening torques: - The tightening torques specified in this data sheet are maximum values and must not be exceeded (maximum values for screw thread). Manufacturer's instruction for the max. permissible tightening torques of the used fittings must be observed! - For DIN 13 fixing screws, we recommend checking the tightening torque individually according to VDI 2230 Edition 2003.

– The data and information contained herein must be adhered to.