Axminster Lathe Manual

2004

600882

SIEG C1 Micro Lathe Mk2

Axminster Reference No: C1Mk 2 Part No: 600882

User M

anual

W H I T EAXMINSTER

Wwww.axminster.co.uk

Page No.

Index of Contents

02

The undersigned, Ole Stilling authorised by Shanghai SIEG Machinery Co., Ltd.No.555 Caofeng Rd., South to No.17

Bridge of Caoan Rd.,Shanghai

declares that this product:

Micro LatheC1

manufactured by Shanghai SIEG Machinery Co.is in compliance with the following standards or

standardisation documents

EN55014-1: 2000, EN55014-2: 1997EN61000-3-2: 2000, EN61000-3-3: 1995

in accordance with Council Directives(89/336/EEC amended by 93/68/EEC)

Declaration of Conformity

Index of Contents.............................................................................................................................................. 2 Declaration of Conformity………….………........……..…………...................................................................2What’s in the Box………….………........……..………….....................................................................................3General Instructions for 230v Machines......................................................................................... 4Initial Assembly and Testing............................................................................................................5Testing........................................................................................................................................... 5-6Specifications….………........……..…………...................................................................................................7Definitions..........................................................................................................................................................7Parts Identification and Description................................................................................................ 8Machine Illustration of the Micro-Lathe...........................................................................................9Parts Identification and Description (Continued)......................................................................... 10Machine Illustration of the Micro-Lathe (Continued).................................................................... 11Parts Identification and Description (Continued)......................................................................... 12Machine Illustration of the Micro-Lathe(Continued)................................................................13-14Settings and adjustments..............................................................................................................15Maintenance..............................................................................................................................16-17Oiling Points...................................................................................................................................17Illustrated Parts Breakdown for the Micro-Lathe (Part 1)........................................................18-19Illustrated Parts Catalogue for the Micro-Lathe (Part 1).............................................................. 20Illustrated Parts Catalogue for the Micro-Lathe (Part 2)............................................................... 21Micro Lathe (Accessories).............................................................................................................22Change Gear Table........................................................................................................................ 23

Quantity Item Model Number1 No. Micro Lathe with Chuck, Chuck Guard and Tool Post fitted. C1

Box containing:-1 No. Set (3) External Jaws for Chuck1 No. 8mm Square ‘T’ Chuck Key 3 No. Rod Handles (detached for packing)1 No. Tailstock Dead Centre (1 x No.1 MT Morse taper)1 No. Double Open Ended Spanner 5mm A/F x 5.7mm A/F1 No. Nipple ‘C’ Spanner 28mm-32mm1 No. Allen Key 2mm1 No. Allen Key 3mm1 No. Allen Key 4mm1 No. Allen Key 6mm2 No. ‘T’ Slot Keepers1 No. Oiling Bottle1 No. Spare Fuse (230v 1 Amp)

1 No. Manual1 No. Guarantee Card

What’s in the Box?

03

Having unpacked your machine and its accessories, please check the contents against theequipment list "What’s in the box", if there are any discrepancies, please contact AxminsterPower Tool Centre using the procedures laid down in the catalogue. Please dispose of thepackaging responsibly, much of the material is bio-degradable. The machine and its accessorieswill arrive coated with heavy corrosion preventative grease. This will need to be cleaned from themachine, its components and accessories prior to it being set up and commissioned. Use coaloil, paraffin or a proprietary degreaser to remove the barrier grease. Be warned, it will stain if yousplash it on clothing etc., wear overalls, coverall et al., rubber gloves are also a good idea, as iseye protection if your cleaning process tends to be a little bit enthusiastic. After cleaning, lightlycoat the exposed metal surfaces of the machine with a thin layer of light machine oil. N.B If youused paraffin/kerosene make sure you apply this thin film sooner rather than later.

Please read the Instruction Manual prior to using your new machine; as well asthe installation procedure, there are daily and periodic maintenance recommendations tohelp you keep your machine on top line and prolong its life. Keep this Instruction Manualreadily accessible for any others who may also be required to use the machine.

!

Good Working Practices/Safety The following suggestions will enable you to observe good working practices, keep yourself and fellowworkers safe and maintain your tools and equipment in good working order.

WARNING!! KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG CHILDREN

Mains Powered ToolsPrimary PrecautionsPrimary PrecautionsThese machines are supplied with a moulded 13 Amp. Plug and 3 core power cable. Before using themachine inspect the cable and the plug to make sure that neither are damaged. If any damage is visiblehave the machine inspected/repaired by a suitably qualified person. If it is necessary to replace the plug, itis preferable to use an ‘unbreakable’ type that will resist damage. Only use a 13 Amp plug, make sure thecable clamp is tightened securely. Fuse at 13 Amp. If extension leads are to be used, carry out the samesafety checks on them, and ensure that they are correctly rated to safely supply the current that is requiredfor your machine.

Work Place/EnvironmentThe machine is not for working outside,do not use when or where it is liable to get wet. If machine does getwet; dry it off as soon as possible, with a cloth or paper towel. Do not use 240va.c. powered machinesanywhere within a site area that is flooded or puddled, and do not trail extension cables across wet areas.Keep the machines clean; it will enable you to more easily see any damage that may have occurred. Cleanthe machine with a damp soapy cloth if needs be, do not use any solvents or cleaners, as these may causedamage to any plastic parts or to the electrical components.

Keep the work area as well lit and uncluttered as is practical, this includes personnel as well asmaterial.

(Under no circumstances should CHILDREN be allowed in work areas)

It is good practice to leave the machine unplugged until work is about to commence, also make sure tounplug the machine when it is not in use, or unattended. Always disconnect by pulling on the plug body andnot the cable. Once you are ready to commence work, remove any tools used in the setting operations(if any) and place safely out of the way. Re-connect the machine.Carry out a final check e.g. check the cutting tool, drill bit etc. is securely tightened in the machine, checkyou have the correct speed and function set, check that the power cable will not ‘snag’ etc.Make sure you are comfortable before you start work, balanced, not reaching etc. If the work you are carrying out is liable to generate flying grit, dust or chips, wear the appropriate safetyclothing, goggles, gloves, masks etc. If the work operation appears to be excessively noisy, wear ear-defenders. If you wear your hair in a long style, wearing a cap, safety helmet, hairnet, even a sweatband,will minimise the possibility of your hair being caught up in the rotating parts of the tool, likewise,consideration should be given to the removal of rings and wristwatches, if these are liable to be a ‘snag’hazard. Consideration should also be given to non-slip footwear, etc. Do not work with cutting or boring tools of any description if you are tired, your attention is wandering oryou are being subjected to distraction. A deep cut, a lost fingertip or worse; is not worth it!Do not use this machine within the designated safety areas of flammable liquid stores or in areas wherethere may be volatile gases. There are very expensive, very specialised machines for working in theseareas, THIS IS NOT ONE OF THEM.Check that cutters, drills etc., are the correct type and size, are undamaged and are kept clean and sharp,this will maintain their operating performance and lessen the loading on the machine.Above all, OBSERVE…. make sure you know what is happening around you, and USE YOUR COMMONSENSE.

!

General Instructions for 240v Machines

!

04

05

Initial Assembly and Testing

Ideally, your lathe should be installed close to a correctly rated power supply, in a warm dryenvironment, well ventilated and illuminated by bright clear natural light, with adequate access allaround the machine, and sufficient adjacent storage space for your tools, accessories andmaterial.

CAN WE DREAM?

The Micro-Lathe is best mounted on a rigid bed, this is to ensure stability of the machine and toattenuate any vibration that is generated when the machine is running, (especially with eccentricwork mounted in the chuck, or on the face plate).

The bed should be flat and set level in both planes, and at a height that enables comfortableoperation of the machine. It is not necessary to anchor the bed through to the floor, but it mustbe stable enough to remain immovable during any normal forceful operations (especiallytightening) carried out whilst operating your lathe.

If you are preparing your own bed for the machine, it should be at least 500mm long by 210mmwide; (to cover the footprint of the lathe bed and integral splashback). You will need to drill three6.5mm holes to allow for bolt fixing. Set out the centres of the holes as follows:- (assuming bedsize indicated above)

First two holes:-

• Hole No.1; from the left side of the bed (Headstock side) 50mm,15mm from the frontedge of the bed

• Hole No.2; from the left side of the bed (Headstock side) 50mm, 100mm from the frontedge of the bed.

• Hole No.3; 420mm from Hole No. 1,15mm from front edge of the bed.

• Bolt the lathe to the bed using M6 bolts and washers.

• Locate and identify the 3 rod handles from the packing box. Fit these to the 3 wheelhandles, (tailstock control, leadscrew feed, traverse feed).

Please read the section entitled Identification and Parts description so that youmay more easily identify the parts to which reference is made in the text.

!

Testing

When the lathe is mounted to your satisfaction, proceed as follows:-

a) Close the chuck jaws.

b) Check the tailstock is ‘nipped’ and barrel lock is tightened.

c) Check that all loose items are removed from the lathe.

d) Set the saddle approximately mid-way along the bed.

e) Press the Emergency Stop Button IN. (Emergency Stop On.)

06

f) Check the Autofeed/Manual Lever is set to manual (Hand logo).

g) Close the chuck guard.

h) Check the speed control is switched OFF (fully anti-clockwise).

i) Check the Forward/Off/Reverse Switch is in the Off position.

j) Connect the machine to the mains supply and switch power on.

k) Turn Emergency Stop switch to the right and allow it to spring out and reset.

l) Check the Green Power LED is illuminated.

m) Turn the Speed Control Switch On (Clicks On).

n) Check the Amber LED (Fault Light) is illuminated.

o) Switch the Speed Control Switch Off ( Clicks Off) and the Amber Led is now Off.

p) Select Forward on the Forward/Off/Reverse switch.

q) Turn the Speed Control Switch On and advance until the Chuck starts to rotate.

r) Lift the Chuck Guard, check the spindle stops and the Amber fault LED illuminates.

s) Reset the Chuck guard, check the spindle does NOT restart and the Amber fault LEDremains On.

t) Turn the Speed Control Switch Off, and that the Amber LED goes off.

u) Turn the Speed Control Switch ON, advance until the spindle starts to rotate.

v) Over a period of approximately 5 minutes advance the speed in stages to maximum, run atmaximum for at least 2 minutes, check that there is nothing untoward, (no excessive vibration,speed progression is smooth etc).

w) If all the above checks are correct, stop the spindle, select the autofeed function, (if necessary‘joggle’ the lead screw handle to enable the gears to mesh. Switch on and advance to a reasonable speed, check the saddle drives smoothly towards the chuck.

x) Stop the spindle, select reverse, switch on and advance to a reasonable speed, check thechuck drives smoothly towards the tailstock.

y) If all the above checks are correct, the final check is to set the spindle running, then hit theEmergency Stop switch. Check the spindle stops and all power indications go Off.

z) Your lathe is now ready for use. Enjoy.

Testing (Continued)

07

Specifications

Definitions

Main Axis This is the axis established through the spindle of the headstock. It is horizontal to and parallel with the lathe bed along its length, as described by the saddle.

Work Axis This is the axis established by the work piece, it is horizontal to, but not necessarily parallel with, the lathe bed, along its length.

Traverse Axis This is the axis described by the traverse slide when it is being moved independently of the saddle. It is perpendicular to the main axis in the horizontal plane.

Compound Axis This is the axis described by the compound slide, if fitted, when it is being operated independently of the traverse slide and the saddle.

Axminster No. SIEG C1 MK2

600882

Rating:

Motor:

Max Swing over the Bed:

Max Distance Between Centres:

Spindle Speed (Forward & Backward):

Reversing Method:

Headstock Taper:

Tailstock Taper:

Clear Bore in Headstock Mandrel:

Leadscrew Pitch:

Thread Pitch Range (Change Wheel Set Req):

Max Traverse Travel:

Max Extention of Tailstock Barrel:

Overall L x W x H:

Weight:

Please note your lathe is suppled with the

following change gears:-

Hobby

240V 50Hz 150W

140mm

250mm

100-2000rpm

Electrical

2MT

1MT

10.5mm

3mm

0.5,0.7,0.8,1.0,1.25mm

60mm

22mm

630 x 330 x 210mm

22kg

19T, 24T, 76T, & 90T. The fixed gear on the headstock is 36T

08

Parts Identification and Description

Please take some time to identify the various parts of your machine so that you arefamiliar with the terminology we will use to enable you to set up and operate your Lathesafely and correctly.

Headstock The ‘engine block’ of the lathe, supports the motor, the spindle, the coverfor the change gears, the drive belt and the driven end of the leadscrew. It also mounts the control panel for the motor and the selector for the leadscrew.

Change gear Protective cover, enclosing the motor pulley, the drive pulley and drive belt cover and the change gear.

Motor 220V d.c. motor

Mounting flange The mounting flange is integral with the spindle and mounts all the material carriers, (chucks, faceplate etc.), it is bored with a No.2 morse taper to acceptthe headstock centre, The boring is then carried through the complete length of the spindle (10.5mm clear) to allow long lengths of round bar to be machined. Your Micro-Lathe is supplied with a chuck adaptor plate and chuckalready fitted to the mounting flange.

Chuck safety A clear acetate cover mounted on a pivot bar on the rear top front face of the cover headstock. It can be tipped out of the way to access the chuck when it is

stationary, and repositioned over the chuck during operation. It is safety interlocked, if it is not in position the motor will not run, or the motor will stop if it is moved whilst the spindle is turning.

Motor control Power On LEDpanel Green LED that indicates that power is available to the motor. i.e. mains is

applied, fuse is intact and the Emergency Stop switch is not activated.Fault LED (marked UNNORMAL)Amber LED that indicates that there is a fault or an incorrect controlsequence. e.g. the chuck guard interlock has been activated or the speedcontrol is activated without forward or reverse direction being selected.The Motor will not run if the fault LED is illuminated. If the safety interlock is activated, the safety interlock will remain in force until the interlock is reset and the start sequence re-initiated.Fuse Cap Access cap for the 20mm fuse cartridge (1 Amp 250V).Speed Control KnobRound raised ridge knob connected to the circuit that controls the motorspeed (100-2000 rpm).Forward /Off/Reverse SwitchThree position switch that controls the direction of rotation of the spindle.Forward indicates that the spindle is turning toward the operator; reverse,the spindle is turning away from the operator. The centre OFF positioninhibits the spindle from turning in either direction, under motor drive.Emergency Stop SwitchRed Domed Mushroom switch; if pressed it removes all power to the machine. It is a ‘knock off, stay off,’ switch. To reset the switch the domedhead must be turned clockwise, which will allow the switch to unlatch and ‘spring out’ and reset itself.

09

Machine Illustration of the Micro-Lathe

Headstock

Change gear cover

Mounting flange

Chuck safety cover

(Chuck & safety cover removed for clarity)

Chuck

Chuck adaptorplate

Power on LED

Fault LED

Fuse cap

Speedcontrolknob

Forward/Off/Reverse

switchEmergencystop

Leadscrewselector

Hand logo TriangularWaveform

logo

Gear changecover knob

(Motor control panel)

Fig 1

Lathe bed

10

Parts Identification and Description (Continued)

Leadscrew A round centre rib switch/lever, which allows selection of the leadscrew toselector ‘autofeed’, i.e driven by the change gear train, (indicated by a triangular

waveform sign), or ‘manually’, i.e. driven by the handle on the end of the leadscrew, (indicated by a ‘hand’ logo).

Lathe bed Solid cast, machined bed. The face machining gives two flat bearing surfaces, whilst the ancillary machining gives a dovetail form to the bed, and forms a rigid stable locating and guiding system for all the machines components.

Saddle Main casting that is precision machined to marry with the lathe bed. It moves parallel to the main axis. It mounts the traverse slide.The accuracy of the fit ofthe saddle to the bed is maintained by the ‘gybe’ strip set in the rear of the saddle dovetail.

Traverse slide Mounted on a ‘dovetail’ land machined onto the top of the saddle. Theaccuracy of the fit of the slide is maintained by the ‘gybe’ strip set in the righthand side of the traverse dovetail slide. The bed of the traverse has two ‘T’ slots machined into it to allow the mounting of the tool post or the compound slide accessory.

Traverse slide A wheel and rod handle, mounted on a shaft that is anchored into a housing control machined in the front of the traverse slide, the shaft is threaded and is

engaged in a dog fixed to the saddle, enabling the traverse slide to be driven back and forth across the saddle perpendicular to the main axis. There is a graduated ring (thimble) on the neck of the handle to allow the movement of the slide to be measured.

Tool Post A double sided tool post. Each tool position has 2 securing bolts to clampthe tool in place. One tool mounting has a fixed ‘bed’ the other has a‘rocking’ bed in a curved seating to allow the tool to be tilted slightly foreor back to allow precise tool heights to be achieved, without the necessity

for fine shims. The tool post is secured into either one of the ‘T’ slots by acaphead bolt passing through the tool post into a ‘T’ slot keeper. The tool post is not keyed into the ‘T’ slot so it can be turned to any angle beforebeing locked in position.

Machine Illustration of the Micro-Lathe (Continued)

11

Lathe bed

Traverse slide

Saddle control

Traverse slide thimble

Tailstock barrelcontrol

Fig 3

Lathe bed

Traverse slide

Tool post

Tool postsecuring bolt

Traverse slidecontrol

Fig 2

Saddle

Splash guard

Leadscrewdrive handle

Typ. 4 cutting toolclamping bolts

Tranverse slide gybestrip adjustors

Offset lockingscrews

Gear change A reeded knob screwed into the front of the headstock, it locates in a slotcover knob in the change gear cover, and is used to secure the cover shut. It is

unscrewed to release the cover to allow it to be swung open.

Tailstock A machined casting that accurately fits to the lathe bed. It carries the tailstockbarrel. The tailstock barrel is machined with a No. 1 MT, which allows the accessories to be mounted (centers, drill chucks, reamers etc). The tailstock is positioned on the bed by a clamp mechanism at the front of the tailstock body. The clamp is tightened by the two caphead bolts in the front flange of the casting. The Tailstock is capable of being offset to allow for taper turning. The offset locking screw is on the right of the tailstock.

Tailstock barrel Wheel and rod handle that controls the backward and forward movement ofcontrol the barrel in the tailstock. The barrel has a travel of 22mm, to allow the

tailstock tooling to be brought into controlled contact with the workpiece,this is indicated on a coarse scale engraved on the barrel itself. The scale

indicates –0 and then 20 plus two (x1mm) divisions. The supplied tailstock centre will self eject at –0. The tailstock control has a graduated ring (thimble)mounted on the neck of the handle so that the amount of movement can be measured.

Tailstock barrel Small ‘petal’ knob that locks the barrel in place once it has been moved into lock the required position.

Leadscrew The leadscrew is a threaded shaft that is anchored into a housing machined into the end of the lathe bed. The shaft runs virtually through the centre axis of the underside of the bed, and is engaged in a dog fixed to the underside ofthe saddle, enabling the saddle to be driven back and forth along the main axis of the bed. The fixed dog is well supported from the front apron of the saddle, and combined with effect of the centralized axis of the leadscrew, results in a very smooth ‘judder’ free movement. The leadscrew can be drivenfrom either end,from the headstock end, via the change gear train, for auto feed and thread cutting, or manually by the leadscrew drive handle. NOTE The leadscrew is permanently engaged into the saddle dog. Any movement of the leadscrew is transmitted to the saddle.

Leadscrew Wheel and rod handle locked onto the end of the leadscrew shaft. Turning thedrive handle handle will turn the leadscrew and drive the saddle back and forth along the

main axis of the lathe. There is a graduated ring (thimble) on the neck of the handle to allow the movement of the saddle to be measured.

Motor securing Two caphead bolts that screw through the change gear compartment bolts bulkhead and into the motor flange. The holes through the bulkhead are

elongated to allow the motor to be moved slightly to maintain the drive belt tension.

Leadscrew This is a small hole situated between two caphead bolts on the lower right oiling point face of the saddle apron. The oil gallery gives direct access to the leadscrew

dog, and enables oil to be spread onto the leadscrew (which is mainly obscured beneath the lathe bed.)

Motor brush Two brush caps located top and bottom of the motor, they are accessed by caps removing the splash guard.

Parts Identification and Description (Continued)

12

13

Machine Illustration of the Micro-Lathe (Continued)

Motor securingbolts

Fig 4

Tailstock Tailstock barrelcontrol

Tailstock barrel lock

Tailstockcentre

Fig 5

Leadscrew drive handleLeadscew (Unseen)

Tailstock clamping bolts

Gear changetable

14

Machine Illustration of the Micro-Lathe (Continued)

Motor

(Splash guard removed for clarity)

Motor brushcaps

Motor brushcaps

Fig 6

Saddle gybe strip adjustors

15

Settings and adjustments

Your microlathe has been factory set and adjusted, however, during its life timeyou may find occasion whereby the lathe needs adjusting to maintain its accuracy andoptimum performance. These adjustments can be made as follows:-

Saddle and Traverse slide adjustment

The saddle and the traverse slide are both mounted over dovetail sections. In order to maintainthe ‘tightness’ of the fit; between the sloping surface of the component and its mating surface agybe strip has been inserted. (At the rear of the saddle, and to the right hand side of the traverseslide).

To adjust the gybe strips, loosen the lock nuts and screw the adjusting screws IN, (4 No. for thetraverse slide and 3 No. for the saddle). ‘nipping’ the component tight to its bedway. Tighten allthe screws to the same torque. Check, using the feed handles, that the saddle/slide are locked inplace.

Unscrew each adjusting screw by a quarter turn, hold the screw (socket grubscrew) in positionand tighten the locknut. Check the component now moves smoothly along its bed, using the feedhandles. If not, carry out the same procedure, unscrew by a third turn this time, etc, if themovement was too tight; by less than a quarter etc., if the movement became too loose.

Repeat the procedure until the movements are smooth and tight. N.B. Always tighten the locknutsbefore testing.

Feed scales

The two thimbles that are mounted on the feed shafts of the leadscrew and the traverse feedshould move freely with the motion of the handle and not slip. The thimbles can be turned, usingmore force, independently of the handle in order to set a predetermined start or finish point. If thethimbles are ‘slipping’ i.e. not maintaining their place relative to the handle, whilst the handle isturning; the cause is almost inevitably dirt, swarf et al., between the pressure plate and thethimble. To rectify this, undo the nut and washer securing the handle to the shaft, remove thehand wheel, and then remove the keyed collar and thimble assembly. Take care that the key doesnot drop out of the shaft. Gradually separate the thimble from the keyed collar, by twisting andturning, until there is sufficient space to clean the mating surfaces.

BE WARNED The friction drive between the collar and the thimble is effected by awire spring (like part of a circlip) that is housed in a groove in the collar and rubs againstthe inside bore of the thimble. If the collar and the thimble are separated too far, thegroove and the spring are exposed. The spring can fall out and if not lost, it is awkwardto re-compress the spring so that the thimble will slide completely back onto the collar.

Once the mating surfaces are clean, mate the key and the keyway and fit the collar/thimbleassembly to the shaft. Refit the washer and the securing nut, and tighten. Tighten until thehandwheel, thimble and collar assembly are too tight to move. Undo the securing nut a quarterturn and check the that the drive handle rotates freely and there is not excessive backward andforward play in the shaft. (The handle etc, forms one side of the drive screw anchor into theslide).

!

!

16

Maintenance

Your Microlathe is a precision tool. In order to maintain this precision and prolong itsuseful life, it is advised that you follow the recommended daily and periodic maintenancetables printed below.

Daily

Carry out a visual inspection. Repair any damage immediately. Minor damage to the beds should be taken out with an oilstone.

Move the saddle and the traverse slide back and forth by hand, check that the movement is smooth.

Spread a light film of oil over the bed and the traverse slide bed.

Directly spray oil on the lead screw after every use.

If the lathe is subject to prolonged use, oil the lead screw and bearings every 3-4 hours.(The lead screw is located underneath and runs the entire length of the lathe bed).

Daily after -use

1. Clean all swarf and chips away from the machine bed, slide surfaces, and the tool post.2. Exercise the slides and ensure no swarf etc., is lodged in the drive shaft tunnels.If you have been using a coolant make sure the machine is throughly dried off. 3. Check the tool, ensure it is usable for the next time, if not re-sharpen or replace the tool tip.4. Lightly oil spray all the machine beds and surfaces, and the tailstock barrel.5. Clean and lightly oil any tools you may have been using (centres, drill chucks, spanners chuck keys etc, and put them away. 6. Switch off the power supply. Disconnect the plug. 7. Cover the machine over with a dust cloth.

Weekly1. Move the traverse slide fully back to give access to the tunnel, blow out to make sureall swarf is cleared away and heavily spray oil the tunnel, exercise the slide to work the oil into the drive thread and to lubricate the dog.2. Spray oil the slide and the lathe bed, exercise the saddle and the slide to spread the oil to all surfaces, both hidden and visible.3. Spray oil under the bed onto the leadscrew. 4. Check the movement of the saddle and the traverse slide, check it is smooth and ‘tight’, if necessary reset the gybe strips.

17

Monthly

Check the belt tension. If necessary reset the belt tension by loosening the two motor securingcaphead bolts, retension the belt and re-secure the bolts.

Every 6 Months

Because the d.c. motor has a heavy permanent magnetic field, it is advisable to dismount thelathe every 6 months, remove the splash guard and remove all the swarf that may have found itsway into the motor housing.

Accessories

There are numerous accessories listed for the machine listed in the Axminster cataloguein section 1.

Maintenance (Continued)

Oiling Points

Oil

(Chuck safety cover removed for clarity)

Fig 7

OIL

18

Illustrated Parts Breakdown for the Micro Lathe (Part 1)

19

Illustrated Parts Breakdown for the Micro Lathe (Part 2)

20

Illustrated Parts catalogue for the Micro Lathe (Part 1)

21

Illustrated Parts catalogue for the Micro Lathe (Part 2)

PC Board Replacement Part No:

Part No: 600883

22

Micro Lathe (Accessories)Vertical slid

eP

art No

: 100028)112m

m T- slot 8m

m Face p

lateP

art No

: (100025)

Travelling stead

yP

art No

: (100027)

Fixed stead

yP

art No

: (100026)

80mm

Indep

endent

4 jaw chuck

Part N

o: (100021)

Com

pound

slide

Part N

o: (100029)

Tailstock centreP

art No

: HA

RD

2

#1M

T Rolling

centreP

art No

: (100032)

Tailstock chuck +shank

Part N

o: (100031)

50mm

Quick vice

Part N

o: (100022)

Chang

e gear set

Part N

o: (100030)

8mm

(11 piece cutter set)

Part N

o: (S

ET

38TC

)

23

Change Gear Table

Fig 8

Fig 9

W H I T EAXMINSTER

W

2004

6008

82

www.axminster.co.uk

Axminster Devon EX13 5PH UK

FREEPHONE 0800 371822

Axminster Reference No: C1Mk 2 Part No: 600882

SIEG

C1

Mic

ro L

athe

Mk2