Top Banner
Electronic Limit Tubular Motor Electronic Electronic Limit + Built-in Receiver 433MHz CE All controls support 433MHz All controls support 230V/50Hz SEPTEMBER 2013 AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS These instructions show how to install, program and use Acmeda’s electronic limit tubular motors: Automate EL S45 Automate Q EL S45 (quiet motor). Automate EL S60 (collision control motor). These motors can be controlled with Automate RF 500 series remote devices: Automate RF 501 (single channel) Automate RF 515 (15 channel) Remote Control RF500 series
8

AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

Jul 27, 2018

Download

Documents

dinhque
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

Electronic Limit Tubular Motor

ElectronicElectronic Limit + Built-in Receiver

433MHz CEAll controls support 433MHz All controls support 230V/50Hz

SEPTEMBER 2013

AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS

These instructions show how to install, program and use Acmeda’s electronic limit tubular motors:

• Automate EL S45

• Automate Q EL S45 (quiet motor).

• Automate EL S60 (collision control motor).

These motors can be controlled with Automate RF 500 series remote devices:

• Automate RF 501 (single channel)

• Automate RF 515 (15 channel)

Remote Control RF500 series

Page 2: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

M O T O R I S E D R O L L E R B L I N D I N S T A L L A T I O N

123

AC

123

123

AC

123

123

AC

123

Page. 2

Only use Acmeda tail

TOP FIX FACE FIX

1

2

3

4

5

Ensure motor & idler have been installed into tube on correct sides and adaptor plate is connected.

Mount brackets into desired position

Locate blind onto bracket; motor end first.Ensure bracket grooves and tongue meet into slots allocated on disc adaptor.

Locate idler onto bracket.Pin will click into place.

Attach bracket covers (if desired), by sliding cover cap up onto bracket.

CIRCUIT INSTALLATION

Page 3: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

P R O G R A M M I N G A M O T O R I N 5 S I M P L E S T E P S

FRONT BACK

SINGLE CHANNEL REMOTE RF501 FIFTEEN CHANNEL REMOTE RF515

R E M O T E O V E R V I E W

B E F O R E YO U B E G I N : PLACE CR2450 (3V) BATTERY INTO REMOTE AND CHECK ALL MOTORS ARE SWITCHED OFF WHEN PRESSING BUTTON SEQUENCE ALWAYS PRESS AND RELEASE EACH BUTTON

STEP 1

STEP 2

Page. 3

PAIRING A MOTOR TO A REMOTE

P2 (x2) UP (x1) or DOWN (x1)

Motor will beep with each button pressed. To confirm pairing, motor will beep 3 times and jolt up and down.

• Switchmotorpoweron(motorwillbeepx5times&jolt).

• Ensurepairingcommenceswithin10secondsaftermotorhascompletedbeepsandjolted.

• Pressbuttonsaccordingtomotorandrollerpositionshownbelow.

CHECK BLIND DIRECTION

PressUP&DOWNbuttonsandensureblindismovingincorrectdirection.IfworkingcorrectlyproceedtoStep3.

Up and down buttons only need to be pressed down once.They do not need to be depressed for blind to operate up and down. UP/DOWN

TO CORRECT BLIND DIRECTION

Pressbuttononmotorheadfor5secondstochangeorientationofblind. Motor beeps & jolts to confirm change of direction.

CheckblinddirectionagainbeforeproceedingtoStep3.

For instructional purposes, the following options have been shown:

Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation.

'AC' Bracket Cover Caps

40mm Motor - Somfy. Somfy Drive & Crown Wheels.

INSTALLATION

ROLLER BLINDS 40mm MOTORISATION

ENSURE 'NOTCH' OF CROWN WHEEL LOCKS WITHIN GAP OF MOTOR HEAD.

ASSEMBLY INSTRUCTIONS

STEP 1: Install Crown Wheel onto 40mm Motor. Ensure 'notch' of Crown

Wheel locks within gap of Motor Head.

STEP 2: Install Drive Wheel onto 40mm Motor.

NOTE: * For Elero Motors, use 'O' ring supplied by Elero to lock Drive Wheel to

40mm Motor. * For Gaposa Motors, use Gaposa Retaining Clip to lock Drive Wheel to 40mm Motor. * For Selve Motors, use plastic retaining clip supplied by Selve to lock

Drive Wheel to 40mm Motor.

STEP 3: Mount 40mm Motor Disk Adaptor onto Motor head with Counter

Sunk Screws.

ONLY USE WITH GAPOSA

Page 57

UPSTOP

DOWN

Channel Display

ChannelSelectionP2 (ProgramButton)

BatterySlot[CR2450(3V)battery]

Removecaptoaccessbuttonsandbattery

MOTOR POSITION

Left Right

ROLL

ER O

RIEN

TATI

ON

Back

roll

P2 (x2) Up (x1)

P2 (x2) Down (x1)

Fron

t rol

l

P2 (x2) Down (x1)

P2 (x2) Up (x1)

Page 4: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

STEP 3

STEP 4

STEP 5

Page. 4

LIMITS ARE NOW SET

FORAUTOMATEQS45&S60MOTORONLY S E T F A V O U R I T E P O S I T I O N

a. Setdesiredlowerlimitposition(usingUPandDOWNbuttons).b. If needed, put motor in Stepping Mode by pressing

P2whilemotorismoving.c. Onceblindisatdesiredposition,pressSTOPfor5secondsuntil

motorconfirmsposition.

To confirm limit, motor will jolt down and up. It is possible to programme multiple motors on each channel.

To program another motor on the same channel, turn OFF motor 1, turn ON motor 2 and repeat steps from 1 to 5.

a.PressP2button(x1).

b.PressUPbutton(x1).

c.PressP2button(x1).

To confirm setting mode, motor will beep 3 times and jolt up and down.

P2 (x1) UP (x1) P2 (x1)

SET UPPER LIMIT FIRST

a. Setdesiredupperlimitpositionfirst(usingUPandDOWNbuttons).b.Whenamoreaccuratesettingisrequiredputmotorin

SteppingModebypressingP2whilemotorismovingup/down.c. Onceblindisatdesiredposition,pressSTOPfor5secondsuntil

motorconfirmsposition.

To confirm limit, motor will jolt down and up.

UP (x1) Hold STOP for 5 sec

SET LOWER LIMIT

DOWN (x1) Hold STOP for 5 sec

TO SEND BLIND TO FAVOURED POSITION, PRESSTHESTOPBUTTONFOR5SECONDS.

Hold STOP for 5 secUP/DOWN

PUT MOTOR IN LIMIT SETTING MODE

• UseUPandDOWNtofindyourfavouriteposition.

• PressSTOPfor5secondsuntilmotorconfirmsposition.

To confirm limit, motor will jolt.

Page 5: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

Itispossibletocreateasubgroupofmotorscontrolledbythesamechannel.

a.PressP2(x2)onchannelalreadyprogrammed(exampleChannel1)

b.PressP2(x1)tocopychannelsettingstogroupcontrolchannel(example Channel 5)

To confirm channel transfer, motor will beep x3 times and jolt up and down.

REPEAT STEPS A & B TO COPY SETTINGS OF ALL MOTORS THAT ARE PART OF THE SUBGROUP INTO CHANNEL 5

MOTOR IS NOW PAIRED TO ANOTHER CHANNEL

a.EnsureMOTOR1isONandallothermotorsareoff.

b.Usechannelselectionarrowstoselectpreferredchannel.

c.Completesteps1-5[Programmingaremoteinfivesimplesteps]

NOTE: If remote is on Channel 0, motor will not pair with remote.

Itispossibletoprogrammemultiplemotorsoneachchannel.

Itispossibletoprogrammemultiplemotorsoneachchannel.Continuetofollowthesameprocedureformoremotors.

CHANNEL SELECTION

Channel number will display on screen

CHANNELDISPLAY

ONLY ONE MOTOR CAN BE ON

P R O G R A M M I N G W I T H A M U L T I C H A N N E L R E M O T E

ONCE ALL BLINDS HAVE BEEN PROGRAMMED, IT IS POSSIBLE TO OPERATE ALL BLINDS TOGETHER

Choose channel 0 to operate all blinds

P2 (x2)

CHANNEL 1

P2 (x1)

CHANNEL 5

Page. 5

Amultichannelremoteallowsyoutocontrolseveralblindsorgroupsofblindsononedevice.Eachchannelcanbeprogrammedlikeasinglechannelremote,byfollowingthebelowinstructions.

MOTOR ONE

a.TurnMOTOR2ON

b.UsechannelselectionarrowstoselectNEXTpreferredchannel

c.Completesteps1-5[Programmingaremoteinfivesimplesteps]

MOTOR TWO

CHANNEL SELECTION

Channel number will display on screen

CHANNELDISPLAY

M O T O R G R O U P S E T T I N G S

51

0

15

14

Page 6: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

RETURN TO FACTORY SETTINGS

CANCEL LIMITS FROM MOTOR

a.PressP2button(x1)b.PressSTOPbutton(x1)c.PressP2button(x1)

a.PressP2button(x1)b.PressDOWNbutton(x1)c.PressP2button(x1)

TO RE-PROGRAM MOTOR P R O C E E D TO S T E P 1 O F P R O G R A M M I N G A M O TO R I N F I V E S I M P L E S T E P S

P2 (x1) DOWN (x1) P2 (x1)

STOPP2 (x1) P2 (x1)

R E M O V E C O L L I S I O N C O N T R O L F U N C T I O N

To confirm cancellation of remote motor will beep x3 times and jolt up and down.

To confirm cancellation of remote motor will beep x3 times and jolt up and down.

C A N C E L L I N G L I M I T S A N D R E M O T E S

IF YOU CANCEL L IMITS ON A MULTICHANNEL REMOTE, ALL CHANNEL SETTINGS WILL BE CANCELLED. TO RE-SET L IMITS P R O C E E D TO S T E P 3 O F P R O G R A M M I N G A M O TO R I N 5 S I M P L E S T E P S

Page. 6

Tomodifylimitsyouneedtocancelalllimitspreviouslyapplied,byfollowingthebelowinstructions.

a. Press P2 (x1)

b. Press STOP

c. Press DOWN

d. Themotorwillbeepandjolttoconfirmthatthecollisioncontrolfunctionhasbeenremoved.

FORAUTOMATES60MOTORONLY

TO RESTORE THE COLLISION CONTROL FUNCTION RETURN TO FACTORY SETTINGS AS SHOWN IN SECTION ABOVE.

P2 (x1) DOWN (x1)STOP (x1)

Page 7: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

S A F E T Y A D V I C E

This system must be installed by a professional automation installer, for whom these instructions have been prepared.

123

AC

123

CREATE A PATH FOR WATER TO RUN OFF TO AVOID CONTACTING MOTOR HEAD

123

AC

123

123

AC

123

123

AC

123

NEVER IMMERSE THE MOTOR IN LIQUID DO NOT DROP IT AND AVOID IMPACTS

DON’T MAKE HOLES IN THE MOTOR

C O N T R O L R A N G E

Page. 7

L1 OPERATING DISTANCE L2 OPERATING DISTANCE EMISSIONFREQUENCY

230v/50H 200m 35m 433.92MHz

L1 L2

motorised roller blind motorised

roller blind

20cm(wall thickness)

Page 8: AUTOMATE S45, Q S45 AND S60 PROGRAMMING … · AUTOMATE S45, Q S45 AND S60 PROGRAMMING INSTRUCTIONS ... Easy-Lock Chain Winder 'AC' Installation Brackets. Top Fix installation. 'AC'

Incorrectoperationcanoftenbefromincorrectsetupofprogramming.Alwaysreadinstructionsbeforeyoubegin.Theinstallerwillguideyouonhowtousetheproductforworryfreeperformance.

AUTOMATE S45 EL AUTOMATE Q S45 EL AUTOMATE S60 EL

Power supply 230V/50Hz 230V/50Hz 230V/50Hz

Capacity 6Nm28Rpm 6Nm20Rpm 20Nm 15 Rpm

Frequency 433.92MHz 433.92MHz 433.92MHz

Running time 4 minutes 4 minutes 4 minutes

Operating temperature -10°C to 40°C -10°C to 40°C -10°C to 40°C

Protective rating IP44 IP44 IP44

Current 0.53amps 0.57amps 0.69amps

Consumption 121watts 133watts 161watts

PROBLEM SOLUTIONMotor does not respond when power is turnedon.

1. Checkthatthepowerisswitchedon.2. Checkpowerconnectiontounitiscompletedbycertifiedelectrician.

Motorhasstoppedworking.

1. Ifthemotorhasbeenusedconsistentlyforfourminutes,themotorcutsoffforsafetyreasons. Allowmotortocooldownbeforeoperatingagain.

2. Checkyouarewithinrangeofoperatingmotor.3. Checktheremotehasfullbatteries.

The motor does not respond when I use the remote.

1. Alightonthesinglechannelremoteilluminateswhenanybuttonispressed. Ifthelightdoesnotilluminate,checkthat(a)thebatteryisinsertedcorrectlyand (b)thebatteryCR2450needsreplacing.Onamultichannelremotedigitalnumbersappear. Ifthisisblank,checkasabove.

PROBLEM SOLUTION

Motorhasstoppedworking.

1. Check wiring of motor2. Checkpowersupplyspecifications3. Checkcompatibilityofthecontrol4. Allowmotortocooldownifithasbeenoperatedforlongperiods.5. Checkyouarewithinrangeofoperatingmotor

The motor does not respond when I use theremote.

1. Checkiftheremotehastobepairedtothemotor(followprogramminginstructionstopair motorwithremote).Motorlimitswillneedtobereset.

2. Onamultichannelremote,ifLCDscreenremainsblankcheckasabove.

Motorisnotrespondingtoremote.

1. Checkremotehasworkingbattery2. WithSingleChannelremoteONLY1Motorcanbeprogrammedatanygiventime.

Checkthatallothermotorsareturnedoffduringprogrammingmultiplemotorson1channel.3. Check surrounding environment for possible RF interference including: door bells, mobile phones, RF house

phones,LEDandplasmaTV’s,microwaves,fluorescentlights,lightingdimmers,computersetc.4. Checkmotorantennaisnottouchingmetalsurfacesofbracketingorwindowtrimorpowersourcewiring.

Blindisoperatinginoppositedirection toupanddownbuttons.

1. Motordirectionorientationneedstobechanged.FollowprogramminginstructionsStep2tochangethe motordirection.Iflimitshavebeenset,theywillneedtoberesetafterchangingorientationofblind.

Motor is moving in step by step mode (notcontinuously)duringprogramming.

1. When programming the limits of a motor, there is the opportunity to put the motor into a step-turning mode (insteadofacontinuousturning)foramoreaccuratesettingofthelimit. Themotorisinthismodebecausethep2buttonhasbeenpressedduringthesettingoflimits(Step4&5). PresstheUporDownbuttonandmotorwillgobacktoturningcontinuously.

FOR INSTALLERS:

T E C H N I C A L D A T A

T R O U B L E S H O O T I N G A U T O M A T E S 4 5 & A U T O M A T E Q S 4 5

Page. 8