Ariens Edge Lowe’s Items 1461301, 1461302, 1461312, 1461313, 1475142, 1476420, 1476421 05292227 • Page 1 of 6 Setup Instructions IDENTIFICATION 1. Seat 2. Left Steering Control Lever 3. Right Steering Control Lever 4. Left Control Arm 5. Right Control Arm 6. Parking Brake 7. Discharge Chute 8. Transaxle Bypass Levers Assembled As Shipped 1 7 4 8 2 6 5 3 Tools for Assembly: • Pry Bar • Cutting Tool • 7/16" Wrench • 9/16" Wrench © 2019 • AriensCo • Brillion, WI 54110
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Ariens EdgeLowe’s Items 1461301, 1461302, 1461312,
1461313, 1475142, 1476420, 1476421
05292227 • Page 1 of 6
Setup Instructions
IDENTIFICATION1. Seat2. Left Steering Control Lever3. Right Steering Control Lever4. Left Control Arm5. Right Control Arm6. Parking Brake7. Discharge Chute8. Transaxle Bypass Levers
Assembled As Shipped
1
7
4
8
2
6
5
3
Tools for Assembly:• Pry Bar• Cutting Tool• 7/16" Wrench• 9/16" Wrench
© 2019 • AriensCo • Brillion, WI 54110
Page 2 of 6
a. Using a pry bar, remove and discard crate top and sides.
b. Remove plastic bag from around unit and discard.
a. Cut cable tie from discharge chute (item 7).
a. Pull transaxle bypass levers (item 8) out to disengage transaxles. Push levers up slightly to lock position.
IMPORTANT: Disengage both left and right transaxles.
WARNING: AVOID INJURY. Read and understand the Safety section in the Operator’s Manual before proceeding.DO NOT start engine until assembly is complete.
1.
CAUTION: AVOID INJURY. Small wood splinters can eject when breaking crate. Wear adequate eye protection and gloves.
2.
3.
7
8
Page 3 of 6
a. Release parking brake (item 6).
a. Push unit off pallet and discard pallet.
a. Push transaxle bypass levers down and in to engage transaxles.
IMPORTANT: Engage both left and right transaxles.
a. Engage parking brake.
4.
5.
6
6.
7.
Page 4 of 6
a. Remove hardware from negative (black) battery cable. DO NOT discard hardware.
a. Secure negative battery cable to negative (open) battery terminal with hardware removed in previous step.
a. Remove upper hardware from right control arm (item 5) and loosen lower hardware. DO NOT discard hardware.
a. Rotate right steering control lever (item 3) into the operating position and reinstall hardware removed in the previous step, but DO NOT fully tighten hardware.
8.
9.
Negative Battery Cable
10.
11.
5
3
Page 5 of 6
a. Remove upper hardware from left control arm (item 4) and loosen lower hardware. DO NOT discard hardware.
a. Rotate left steering control lever (item 2) into the operating position and reinstall hardware removed in the previous step, but DO NOT tighten hardware.
a. Rotate steering control levers outward.
a. Rotate seat (item 1) into the operating position.
12.
13.
4
2
14.
15.
1
Page 6 of 6
a. Return steering control levers to operating position and align levers. Refer to operator’s manual for steering lever adjustment instructions.
a. Tighten right steering control lever hardware.
a. Tighten left steering control lever hardware.
16.
17.
18.
WARNING: AVOID INJURY. DO NOT proceed until operation and safety rules are fully understood.
Read and understand Operator’s Manual before proceeding.
Related Documents
