Aluminium Smelting & Production

8/9/2019 Aluminium Smelting & Production

1/19

7

Chapter 2. Production and Processingof Aluminum

2.1 Ext ract i on of A l umi num

The extraction of aluminum from its ore and subsequent processing into finished prod-ucts takes place in a series of successive operations, each largely independent of the other.Generally the various processes are carried out at different plant sites. A summary of production steps from the bauxite mine through casting is given in Fig. 2.1.

2.1.1 Bauxite mining

Aluminum comprises approximately 8% of the earth’s crust, making it second only tosilicon (27.7%). Iron is third at about 5%. Metallic aluminum is not found in nature; itoccurs in the form of hydrated oxides or silicates (clays). The principal ore from whichaluminum is extracted is called bauxite after the town of Les Baux in southern France

where the ore was originally discovered. Bauxite occurs mainly in the tropics and insome Mediterranean countries. Today, the main mining locations are in Latin America,Australia, India, and Africa.

Bauxite is a weathered rock containing two forms of hydrated aluminum oxide, eithermostly a monohydrate AlO(OH) in caustic bauxite, or mostly a trihydrate Al(OH)3 inlateric bauxite. Besides these compounds, bauxite contains iron oxide, which usually givesit a reddish-brown colour, as well as silicates (clay, quartz) and titanium oxide. The crys-tal structure also contains 12–20% by weight of water. Tropical monohydrate bauxite gradesyielding 35–55% Al

2O

3will no doubt continue to be the most favored aluminum ores for

many decades.

Laterite rocks similar to bauxite, but with lower alumina content, are available in largequantities. Clays became a source of alumina to a limited extent in Germany during the

Fig. 2.1: Production steps for aluminum.


2/19

8

Second World War. In addition, many other types of rock contain considerable amountsof alumina, such as kaolin, nepheline, andalusite, leucite, labradorite, and alunite. Theformer Soviet Union exploited such ores to maintain partial autonomy, but these oresplay no significant role in today’s aluminum production. Chapter 16 will show that theworld’s bauxite supplies are guaranteed into the distant future.

2.1.2 The alumina plant

The starting material for electrolytic smelting of aluminum is pure, anhydrous alumi-num oxide (Al2O3) called alumina. In the Western World, the Bayer

1 process, invented inthe 19th century, is by far the most important process used in the production of alumi-num oxide from bauxite. The process has been refined and improved since its inception.Fig. 2.2 shows that the production of alumina is a complex chemical process. The alu-mina content of bauxite ores varies from one deposit to another, and methods of treat-

ment differ accordingly (see 16.1.2). This means that each alumina plant is almost tailor-made to suit a particular bauxite. The processes are nevertheless basically similar, and ageneral description is given in the following. The bauxite from the mine is crushed andground. It is then mixed with a solution of caustic soda and pumped into large auto-claves. There, under pressure and at a temperature of 110–270°C, the alumina containedin the ore is dissolved to form sodium aluminate. The silica in the bauxite reacts andprecipitates from solution as sodium-aluminum-silicate. Iron and titanium oxide and otherimpurities are not affected chemically, and being solid, settle out of solution. This wastematerial, known as red mud, is separated from the sodium aluminate solution, washedto recover the caustic soda, and then pumped to disposal areas.

The disposal of red mud can present an environmental problem simply because there isso much of it. From a few alumina plants, red mud is deposited on the sea bed understrictly controlled conditions. One very common method of disposal is to contain themud in an area surrounded by dikes. After an interval of some years, these ponded areascan be recultivated to eliminate “visual pollution.” Although a great deal of effort has

been expended on finding and developing various uses for red mud, no bulk applicationof commercial value has yet been found.

Adding the weak soda washed out of the red mud to the sodium aluminate solution

dilutes it and cools it to about 100°C. With stirring and cooling to 60°C, aluminum hy-droxide Al(OH)3 (hydrargillite) precipitates. Seeding the liquor with crystals from a pre-vious cycle helps to control precipitation. Vacuum filters separate the hydroxide precipi-tate, which is then washed with pure water. Calcination in rotary kilns or in fluidized

beds at 1100°C to 1300°C finally converts the hydroxide to a dry, white powder. Thispowder is technical purity alumina, containing as impurities at most 0.01–0.02% SiO 2,0.01–0.03% Fe

2O

3, and 0.3–0.6% NaO

2.

The grade of the alumina (particle size, α- and γ -Al2O3 content) can be influenced byprecipitation and calcining conditions, and it is usual to differentiate between two maingrades, i.e. “floury” alumina, which is highly calcined and contains mostly α-Al2O3, and“sandy” alumina, which calcined to a lesser degree with mainly γ -Al2O3 in the hydrated

1 Named after the Austrian K.J Bayer.


3/19


4/19

10

produce Portland cement in a second calcination step. Processing about 4–4.5 tonnes of nepheline ore yields 1 tonne of alumina, 9–11 tonnes of cement, 0.6–0.8 tonnes of sodaash, and 0.2–0.3 tonnes of potash.

According to the grade of the bauxite ore, 2–3 tonnes of ore yield one tonne of aluminaand about one tonne of red mud (dry weight). When designing an alumina plant, factorsother than the type of bauxite ore to be used as feed material and the form of alumina to

be produced have to be taken into consideration. A high silica content of the bauxite isundesirable because insoluble sodium-aluminum-silicate will form, causing losses of caus-tic soda and alumina which increases input material costs. Energy consumption is an-other consideration. The economical operation of the Bayer process requires the rationaluse of energy for steam generation and calcining. Inexpensive fuel is desirable becausethe process needs a large amount of thermal energy. The end product of the aluminaplant is a dry white powder that is the feedstock for aluminum smelting.

2.2 Primary A l uminum Product i on

Throughout the world, primary aluminum is still produced by the electrolysis of alu-mina in molten fluoride salt. This is, in essence, the process that Hall and Héroult in-vented, and which is named after them, but its efficiency has been significantly improvedover the years. The electrolysis plant—the aluminum smelter—needs large amounts of electrical energy. Therefore, besides good bulk transport facilities, abundant inexpensiveelectric power is essential. Because hydroelectric power is a relatively inexpensive andclean source of energy, aluminum smelters are mostly built in countries with readily avail-

able hydroelectric power, such as Canada, Norway, Venezuela, and Brazil, or in countrieswith abundant deposits of low-grade coal such as Australia or the Republic of SouthAfrica (RSA). Furthermore, the same regions lack other local industry to use this energy,and it is impracticable to transport electric power over very long distances to the indus-trialized regions that could use it. Considering their large energy consumption, alumi-num smelters are major customers that guarantee a stable base load and, thereby, help toreduce their power suppliers’ unit costs. At present, hydroelectric sources produce thepower for about two-thirds of world aluminum production, although placing a smelternext to a nuclear power plant can also be economically attractive, as at Dunkerque inFrance. Fig. 2.3 shows an aluminum smelter with its long potrooms and tall aluminasilos.

2.2.1 The electrolysis process2

In the Hall-Héroult process, the electrolyte is molten cryolite (Na3AlF6) in which 2–8% of alumina (Al

2O

3) is dissolved. To lower the melting point, industrial cryolite-alumina mix-

tures also contain various amounts of other salts, such as aluminum fluoride (AlF3) andcalcium fluoride (CaF2); sometimes lithium carbonate (Li2CO3) is present and, less fre-quently, magnesium fluoride (MgF

2) is introduced. These additions also improve current

efficiency and reduce evaporation losses. For each tonne of aluminum produced, thesmelting process consumes, in addition to electrical energy, about 1.95 tonnes of alumina,0.5 tonnes of anode coke, and small amounts of fluoride salts.2 By G.W. Bulian.


5/19

11

The electrolysis cell, or “pot,” shown schematically in Fig. 2.4, is shaped like a shallowrectangular basin. It consists of a steel shell with a lining of fireclay brick for heat insula-tion, which is, in turn, lined with carbon bricks to hold the fused salt electrolyte. Steel

bars carry the electric current through the insulating bricks into the carbon cathode floorof the cell. Carbon anode blocks are suspended on steel rods, and dip into the electrolyte.As the electric current flows through the electrolyte, it breaks down the dissolved alu-mina into its component elements as metallic aluminum and oxygen gas. The oxygen

reacts with the carbon anodes, forming bubbles of CO and CO2 gas. Liquid aluminumsettles on the bottom of the cell since it is denser (specific gravity 2.3 at 960°C) than theelectrolyte (specific gravity 2.1). Periodically, this aluminum is siphoned off by vacuuminto crucibles. To replace the alumina consumed in the reaction, more alumina must beadded. Today, computer-controlled devices called point feeders automatically inject thealumina powder through the top surface crust of solidified electrolyte. Pots may eachhave two or more point feeders, depending on their size.

At 4–4.5 volts per cell, the operating voltage is considerably higher than the theoreticaldecomposition voltage of aluminum oxide. The difference is due to various voltage losses,

which are unavoidable under industrial conditions. The resulting excess power gener-ates heat, which maintains electrolyte temperature. More heat comes from the slow burn-ing of the carbon anodes.

Fig. 2.3: View of a modern aluminum smelter in Canada, showing the harbor and alumina silos in the

foreground and the potrooms behind.


6/19

12

The cell is controlled mainly by regulating the anode/cathode distance and the directcurrent, which can be up to 300,000 A in modern cells. In modern smelters, process-con-trol computers connected to remote sensors ensure optimal operation, this being one of the main reasons for today’s high energy efficiency. The individual cells are connected inseries, bringing the supply voltage to over 1000 V, which is the optimum operating volt-age of thyristor power supplies. Thus, a modern potline consists typically of 264 cells in

series, supplied at 1150 V. Aluminum busbars carry the current from one cell to the next.

As explained above, anode material is consumed in the classical Hall-Héroult reaction.Most smelters use prebaked carbon anode blocks. These are manufactured by first com-pacting blocks from a paste of calcined petroleum coke and tar pitch. Formerly made bypressing, the blocks were of uneven density, and tended to fail in service. Today, vibrat-ing the paste under load, and often under vacuum, produces blocks of more uniformdensity. After this compacting process, the anodes are prebaked in a calcining furnace.

Instead of prebake anodes, some older smelters use Söderberg anodes. These are con-

tinuously formed in-situ by feeding “green” (raw) paste into the top of a sheet steel shellover the cell. Heat from the process bakes the paste to solid anode coke. There are twovariants of the Söderberg process. These are referred to as either vertical- or horizontal-stud processes, depending on the positioning of the steel pins that deliver electric currentinto the anode. Disadvantages of this process are: low current efficiency of about 86–90%(compared with 95% in modern prebake smelters) and more fume emissions than withprebake anodes. Such fumes create problems with workers’ health. No more Söderbergcells are being built, and those existing are progressively being shut down, converted, orreplaced. What follows will only deal with modern plant using prebake anodes.

Fumes leaving the cells contain mainly CO2, CO, and SO2 if the anode coke containssulfur, together with smaller amounts of fluorine compounds and dust. Most of the gas-eous fluorine exists as hydrogen fluoride HF, and the dust is mostly fluorine compoundssuch as cryolite and aluminum fluoride, as well as some alumina.

Fig. 2.4: View of the cross-

section of an electrolysis cellwith point feeding: (a) steel

cathode shell; (b) insulation; (c)

steel cathode collector con-

ductor bar; (d) cathode; (e) riser

conductor; (f) bridge, height-

adjustable traverse bar sup–

porting anodes; (g) anode; (h)

alumina feed funnel; (i) point

feeder; (k) pot covering hood;

(l) pot gas and dust extraction.

(VAW)


7/19

13

Under unfavorable conditions, the pots may produce small quantities of the fluorocar- bon compounds CF4 and C2F6, which are known to take part in the “greenhouse effect” of the upper atmosphere. However, this emission happens only during the so-called “an-ode effect,” which occurs when the alumina concentration drops below a critical thresh-old. During the anode effect, the cell voltage climbs from the normal 4.5 volts to over 40volts. In modern electrolysis pots, which are fitted with pneumatic alumina transportand feeding systems, the alumina concentration can be held at an almost constant level.With the aid of modern, microprocessor-controlled potroom control, the frequency of

anode effects, and hence the emission of fluorocarbons, can be much reduced.3

Formerly,about one per day and per cell, anode effects can now be reduced to one every two months by automated alumina feeding.

Since emissions of fluorine compounds, either as gases or dust, can harm the environ-ment, these fumes are collected by hoods over modern cells. In a process called dry scrub-

bing, the fluorides bind to sandy alumina during intensive mixing. This fluoride-loadedalumina then goes to dust separators and to electrostatic dust filters, and finally back tothe potline as feed material. The fluoride-free remainder is exhausted to atmosphere.Although technically difficult and capital intensive, dry scrubbing meets the low emis-

sion limits required for modern smelters. In recovering lost fluorine compounds and re-cycling them to the cell, dry scrubbing shows that environmental protection and economy

3 Such a control system is the “ELIAS” (Electrolysis Automation System) of the VAW Company. Other leading

primary aluminum producers use similar or equivalent process-control sysems. See also Chapter 16.

Fig. 2.5: Temperature distribution in a 180 kA electrolysis cell, drawn using a computerized

mathematical model. (VAW) A color version of this figure appears on page 425.

200°

800°

960°

900°

400°


8/19

14

are not necessarily opposed, but can aim in the same direction (see Chapter 16).

The aluminum industry has made considerable technical advances since the Hall-Héroultprocess was introduced and is working on further improvements. Specific energy con-sumption has fallen in the last 35 years from 21 to almost 13 kilowatt-hours per kilogramof aluminum produced. This was made possible by advanced computer control of all therelevant parameters in the electrolysis cell. Development of new cells today involves com-puter modeling to optimize chemical, electrical, magnetohydrodynamic, and thermal

conditions. Fig. 2.5 shows a calculated temperature distribution as an example of thecomputer-aided development of electrolysis cells.

Formerly, manual operation of the cells required wide access routes for vehicles betweenthe potlines, but in modern smelters (Fig. 2.6) manipulator cranes perform most tasks. Incontrast to the longitudinal alignment of anode beams in earlier potlines, the newer de-signs have anode beams arranged transverse to the line of cells. This arrangement hasseveral advantages: it better compensates magnetic fields in the cell, requires less floorspace in the potroom, and reduces the length of conductors, thereby reducing resistancelosses. Computer modeling has shown that to reduce magnetic fields, electrical busbar

connections should be through the transverse “risers” rather than as previously throughthe ends of the anode beams.

Fig. 2.6: Inside view of a potroom with cells arranged crosswise; in the foreground is a 240 kA pot

with electrical connection through risers at the side. (VAW)


9/19

15

2.2.2 Other processes for producing aluminum

Other processes for extracting aluminum have been developed. Here, it is worth men-tioning two electrolysis processes (using aluminum chloride or, alternatively, aluminum

sulfide electrolytes) and two metallothermic ones (the Toth process, in which manganesereduces aluminum chloride, and the carbothermic reduction process, in which carbonreduces alumina). Except for the aluminum chloride electrolysis, technical or economicreasons have prevented these processes from developing beyond the laboratory or pilotscale.

For a few years from 1976, Alcoa operated an aluminum chloride electrolysis plant witha capacity of 15,000 tonnes per year. However, this was later shut down, the reason given

being the excessive cost of producing anhydrous aluminum chloride feedstock by chlori-nating alumina. Aluminum chloride feedstock is dissolved in an electrolyte consisting

mainly of sodium chloride (NaCl) and potassium chloride (KCl) or lithium chloride (LiCl).Electrolysis releases aluminum metal and chlorine gas. The latter is recycled by chlori-nating alumina. The main advantage of the chloride process over the Hall-Héroult pro-cess is a saving of 30% in electric power consumption. In addition, the process avoidsfluoride emissions and makes more optimum use of anode coke, since it can work withmultipolar graphite electrodes. At 700°C, the temperature is much lower than that in theHall-Héroult cells, so that it needs less heat energy. In spite of these advantages, its chancesof success remain uncertain because, as mentioned above, the economics of producingaluminum chloride feedstock remain unclear. Some observers have noted two furtherdisadvantages: the tower-like multistory building, and corrosion problems within the

system for circulating the electrolyte.

2.2.3 Primary aluminum

Smelters produce primary aluminum (as opposed to secondary, or recycled, aluminum)with a purity of 99.7–99.9%. The main impurities are iron and silicon, together with smalleramounts of zinc, magnesium, manganese, and titanium. Typical analyses also show tracesof copper, chromium, gallium, sodium, lithium, calcium, vanadium, and boron. Passingchlorine gas through the molten aluminum can remove traces of sodium, lithium, cal-cium, and, if necessary, magnesium. Filtering can remove suspended particles, such asoxides and carbides. Hydrogen, the only gas soluble to any extent in aluminum, can beremoved by degassing with chlorine, nitrogen, or, better still, argon (see Chapter 5).

Aluminum for electrical use must not exceed fairly low maximum levels of titanium,vanadium, manganese, and chromium, because these elements greatly reduce conduc-tivity. Conductor-grade aluminum is generally produced by selecting the purer metalavailable from the best cells. If the level of these elements is still too high, adding boroncan precipitate them as insoluble borides, which have little effect on conductivity.

International standards distinguish two types of unalloyed aluminum: “pure aluminum”of 99.0–99.9% and “high-purity” aluminum of at least 99.97%, which is produced by fur-ther refinement. Table 2.1 shows the different grades of pure and high-purity aluminum,as classified by Aluminum Association standards.


10/19

16

T a b l e 2 . 1 : C o m p o s i t i o n o f u n a l l o y e d a l u m i n u m

i n g o t s *

( C o m p

o s i t i o n i n w e i g h t p e r c e n t ;

m a x i m u m u n l e s s a r a n g e i s s h o w n ) †

A l A s s o c .

A l .

d e s i g n a t i o

n

S i

F e

C

u

M n

M g

C r

N i

Z n

T i

E a c h

T o

t a l

( m i n . )

1 0 5 0

0 . 0 2 5

0 . 4 0

0 . 0 5

0 . 0 5

0 . 0 5

—

—

0 . 0 5

0 . 0 3

0 . 0 3

9 9 . 5 0

1 0 6 0

0 . 0 2 5

0 . 3 5

0 . 0 5

0 . 0 3

0 . 0 3

—

—

0 . 0 5

0 . 0 3

0 . 0 3

—

9 9 . 6 0

1 1 0 0

0 . 0 9 5 S i + F e

0 . 0 5 – 0 . 2 0

0 . 0 5

—

—

—

0 . 1 0

—

0 . 0 5

0 . 1 5

9 9 . 0 0

1 1 4 5

0 . 0 5 5 S i + F e

0 . 0 5

0 . 0 5

0 . 0 5

—

—

0 . 0 5

0 . 0 3

0 . 0 3

—

9 9 . 4 5

1 1 7 5

0 . 0 1 5 S i + F e

0 . 1 0

0 . 0 2

0 . 0 2

—

—

0 . 0 4

0 . 0 2

0 . 0 2

—

9 9 . 7 5

1 2 0 0

1 . 0 0 S i + F e

0 . 0 5

0 . 0 5

—

—

—

0 . 1 0

0 . 0 5

0 . 0 5

0 . 1 5

9 9 . 0 0

1 2 3 0

0 . 7 0 S i + F e

0 . 1 0

0 . 0 5

0 . 0 5

—

—

0 . 1 0

0 . 0 3

0 . 0 3

—

9 9 . 3 0

1 2 3 5

0 . 6 5 S i + F e

0 . 0 5

0 . 0 5

0 . 0 5

—

—

0 . 1 0

0 . 0 6

0 . 0 3

—

9 9 . 3 5

1 3 4 5

0 . 3 0

0 . 4 0

0 . 1 0

0 . 0 5

0 . 0 5

—

—

0 . 0 5

0 . 0 3

0 . 0 3

—

9 9 . 4 5

1 3 5 0

0 . 1 0

0 . 4 0

0 . 0 5

0 . 0 1

—

0 . 0 1

—

0 . 0 5

—

0 . 0 3

0 .

1 0

9 9 . 5 0

* F r o m T a b l e 6 . 2 o f A l u m i n u m

S t a n d a r d s & D a t a ( t h e A l u m i n u m A s s o c i a t i o n , 1 9 9 7

) .

† S e e o r i g i n

a l r e f e r e n c e f o r a d d i t i o n a l l i m i t r e s t r i c t i o n s

O t h e r s


11/19

17

2.2.4 High-purity aluminum

For most applications,the purity of aluminum as it comes from the potroom (i.e., up to99.9%) is adequate. High-purity aluminum of at least 99.97% aluminum content is neces-

sary for certain special purposes (e.g. reflectors or electrolytic capacitors); for such appli-cations, the potroom metal has to be further refined in an additional process. Less thanone percent of the total volume of primary metal undergoes this second stage of refining.

High-purity aluminum is produced by so-called three-layer electrolysis (the Hoopes cell).This cell, in contrast to the two layers of the Hall-Héroult process, operates with threeliquid layers. The lowest layer, called anode metal, receives the input of normal primaryaluminum to which has been added about 30% copper to increase the specific gravity to3.4–3.7. The second layer is the molten electrolyte with a specific gravity of about 2.7–2.8,and the uppermost layer is the separated high-purity liquid aluminum with a specific

gravity of 2.3. The cell has a siphon chamber for loading the anode metal.

Aluminum produced in this way is 99.99% pure. Higher purities of up to 99.9999% (“six-nines” aluminum) can be obtained using one or two additional zone-refining operations.Zone-refining traps impurities in a molten zone that moves gradually from one end tothe other of a specially prepared ingot. Lesser purities in the range 99.97–99.98% are to-day produced in limited quantities by fractional crystallization. Here, any impurities thatform an eutectic system with aluminum can be concentrated in the liquid melt, whichcan be separated from the primary crystals of aluminum, and the purer aluminum sepa-rated once it has crystallized out.

Another way of producing 99.97–99.98% purity is simply to mix higher-purity metal withthat of a lower purity. The organic electrolysis which was formerly used for making thehighest-purity metal is seldom if ever used because the highly inflammable electrolyterequires extreme safety measures and no economic advantage over zone-refining.

2.3 The Product i on of Secondary A l umi num

A used aluminum part, whether extrusion, sheet or plate, forging or casting, or a used

finished product such as a can or a cast wheel, can be efficiently remelted and recon-verted via the appropriate fabrication route—ingot casting, extruding, rolling or die-cast-ing—into a new usable form. The resulting material loss by surface oxidation, called meltloss, varies from a few tenths of one percent in the case of clean, uncoated, massive cast-ings or forgings to as much as 10% for light-gage coated packaging scrap. Melt loss de-pends very much on the type of feedstock: its shape and gage and the type and thicknessof lacquer or other form of coating—all of these factors have a major influence on theamount of metal “lost.” Melt loss also depends very much on the chosen method of melt-ing.

The economics of recycling, together with improved techniques of scrap preparation andmelting provided higher yields and thus led to the further development of the secondaryaluminum industry. This field grew rapidly during the 1950s, with the blossoming of thenonmilitary uses of aluminum; today, it meets 35% of the total aluminum metal demand


12/19

18

in Europe. The supply of raw material to this secondary aluminum industry is a highlyorganized business involving collection and sorting networks and scrap trading.

2.3.1 Feedstock

Aluminum recycling forms the basis of the secondary aluminum industry. Today, sec-ondary smelters serve chiefly to supply die-casting plants with casting alloys, using metalrecovered from mixed scrap and dross. Much secondary metal goes into cast parts for thecar industry, where demand both from independent foundries and the integrated in-plant casthouses of the car plants themselves has grown steadily over the years. Fig. 2.7

shows schematically the traditional method of scrap preparation. There has been someconfusion in the terminology, so it is as well to be clear as to what is meant by “scrap” inthe context of recycling. The principal feedstocks for the secondary aluminum industryare:

• Process scrap generated during the manufacture of finished aluminum products.This will be referred to as “process scrap” or “runaround scrap”

• Old scrap arising from products that have reached the end of their useful lives. This,often representing the greater part of the feedstock, will be referred to simply as“scrap.”

• The residues from result of skimming and cleaning furnaces in aluminum casthouses,

consisting mainly of a mixture of metal and oxides. This is usually called “dross,”and it will be referred to as such.

Fig. 2.7: Schematic showing the traditional processing of old scrap for making secondary aluminum.


13/19

19

2.3.2 Process technologies

Scrapped aluminum products are broken into small pieces and separated from dirt andforeign materials so as to yield feedstock suitable for remelting. This is done using break-ers, shredders, magnetic, and settlement/flotation separators. Such scrap typically con-tains alloys of many types, all mixed together. A more sophisticated kind of recycling wasdeveloped in the seventies and eighties for process scrap and used beverage cans (UBC).

By selectively collecting scrap in targeted alloy categories, the goal was to recycle thematerial back into products similar to those from which it originated. Thus, the casthousesof extrusion plants produce extrusion billets from process scrap and from recycled scrapextrusions. Similarly, the high rate of recovery of used beverage cans from the consumer,most notably in the USA, enables a large proportion of canstock coils to be madefrom UBC.

The demand for more selective groupings of scrap from the growing volume of materialavailable for recycling will drive the scrap metal industry to develop refined and auto-mated techniques of sorting scrap into the various alloy families. The steady growth in

the consumption of aluminum in the past few decades will result in a higher rate of aluminum-containing goods reaching the end of their service lives and a correspond-ingly steady increase in the volume of scrap available for recycling as more and morealuminum-containing goods reach the end of their service lives. This trend will intensify

Fig. 2.8: Increase in the volume of scrap in western Europe arising from an assumed growth rate in

aluminum consumption of two percent per year. Assumed service life: building—30 years; machine

tools—20 years; electrical—15 years; transport—11 years.


14/19


15/19

21

from the organic material. Another technique for handling scrap for recycling in bulkuses some form of rapid analysis method coupled with mechanical sorting. In this way,scrap segregated into the main alloy families can be subjected to special pretreatmentand melting processes so as to remove organic coatings of all sorts while ensuring therecovery of a higher fraction of the aluminum content.

Fig. 2.9 illustrates a process known as the “R-Furnace.” Coatings in the form of lacquer orlaminated plastic are separated from the metal by pyrolyzation and the resulting gases,rich in energy, burn to supplement the primary fuel. The amount of salt needed to tie upthe dross is reduced to a minimum. Comparison with the conventional process makesthis clear: the rotary hearth furnace uses 400 kg of salt per tonne of scrap; the R-furnaceuses only 25 kg per tonne.

This and similar new technologies for melting coated scrap are environmentally friendly

and they do not generate excessive amounts of polluting by-products such as salt slag.They yield high-value aluminum alloys with a good recovery rate, thus enabling a morecomplete aluminum material cycle than was possible with the older techniques. The ar-rival of these processes changed aluminum recycling in a fundamental and far-reachingway (see, also, Chapter 16).

Figure 2.10: Operations and products in semifabricated products plants and foundries. Special casting

processes like strip casting or wire/bar casting are not shown.

melting

casting

wrought alloysunalloyed Al

foundry(casting) alloys

ingot casting

ingot rolling *

cold rolling

stretching,leveling

plate, sheet,strip, foil

extrusion *

drawing stretching

straightening

sections, tubingrod, bar, wire

forging*

free form forging*drop forging*

forgings

mold casting

sand casting,

permanentmold casting,die casting

cast parts

* These processes are usually carried out between 350 to 550°C


16/19

22

2.4 Processi ng of A l umi num

2.4.1 Cast houses and foundries

2.4.1.1 Ingot casting (DC casting)

Primary aluminum and also scrap are cast into rolling ingot (slab), extrusion ingot (billet)and wire bar ingot, and, to a lesser extent, forging stock in the casthouses of the reductionplants or semifabricated products plants. Appropriate alloying elements are added in themelting or holding furnaces, after which the metal is cleaned and cast. Reduction plantcast houses also produce pigs from a part of the primary metal.

2.4.1.2 Mold casting

In foundries, cast products are usually produced from prealloyed metal supplied by sec-ondary smelters. In some cases, casting alloys are prepared from a primary metal base forproducts that must meet rigid requirements that can be achieved only with minor amountsof impurities (for example, iron).

There are three main aluminum casting processes: sand casting, permanent mold cast-ing, and die casting, which usually produces a finished part in one step. Unlikesemifabricated products plants, foundries may deliver a finished product which requiresno further forming. For this reason, foundries are not usually classified as semifabricated

products plants and are shown separately in Fig. 2.10.

2.4.1.3 Special casting processes

The continuous casting of strip, wire, and rod belong to this family. Lately, continuousstrip casting processes are experiencing the most rapid growth.

2.4.2 Semifabricated products plants

An aluminum plant for the production of semifabricated products (sometimes called a“semis” plant) may receive ingots for fabrication directly from the reduction plant orfrom their own remelt shop. Typical fabrication steps in a semis plant are shown in Fig.2.10. The first operation is the hot deformation of the cast ingot at temperatures between350°C and 550°C. Depending on the process, the deformation may be executed by hotrolling, extrusion, or forging. Such hot-working is often followed by cold deformationsuch as the cold rolling of sheet or drawing of tube. Some semifinished products aresupplied in the as-fabricated condition in the form of extruded shapes, forged parts, andhot-rolled sheet or coils. Prior to delivery, extruded shapes are usually stretched forstraightening and stess relieval, which imparts a small amount of cold work to the mate-

rial.


17/19

23

2.4.3 Subsequent fabrication of aluminum semifabricated

products

Semifabricated products undergo further fabrication before they are sold to the consumeras a finished product. The fabricators use a great number of techniques in finishing alu-minum. The primary objective of the fabricator is to impart the desired shape to the workpiece. The techniques may produce chips (milling, turning, boring, etc.) or be chipless(deep drawing, stretch forming, impact extrusion, blanking, bending, spinning). Surfacetreatment of aluminum is of special importance and may include mechanical polishing,etching, brightening of the aluminum by electrolytic or chemical processes and the gen-eration of thicker oxide layers through anodizing.

The picture would not be complete without mentioning joining techniques, which have been greatly improved in recent years, especially in the field of welding under protectivegas, as well as in the use of adhesives.

2.5 Types of A l umi num A l l oys

As mentioned earlier, the production of semifabricated products utilizes three differenttypes of aluminum, namely super purity, commercial purity, and alloys. Alloys are used

for producing castings or fabricating wrought products. The alloys used for castings con-tain a greater amount of alloying additions than those used for wrought products. Theaddition of alloying elements has the effect of strengthening the wrought alloys and im-proving the castability of the casting alloys.

Figure 2.11: Synopsis of the principal aluminum alloys (commercial alloys on the basis of primary

aluminum).


18/19

24

Today, more than half of the semi-finished production is delivered in alloys, most of theremainder in commercial-purity aluminum with only a small quantity of super-purityaluminum being produced.

It is necessary to differentiate between wrought and casting alloys. Both of these alloytypes are subdivided into those alloys that are solution heat treatable and those that arenot. Wrought alloys are genarally used for further fabrication, for example, rolling, forg-ing, extrusion, and drawing. Casting alloys are used for cast parts and have the flowcharacteristics favorable for this process. For example, an alloy with good castability must

be able to fill the mold completely and have a low sensitivity toward cracking duringcasting.

The most important elements that are added to aluminum, in alphabetical order, are bis-muth (Bi), boron (B), chromium (Cr), copper (Cu), iron (Fe), lead (Pb), magnesium (Mg),manganese (Mn), nickel (Ni), silicon (Si), titanium (Ti), zinc (Zn), and zirconium (Zr).Magnesium is the most frequent addition to aluminum. In some alloys, two or moreelements are used in combination (e.g., magnesium together with silicon or manganese).There are also alloys of aluminum containing only manganese or only silicon. The alloy-ing elements are added to bring about changes in the properties of aluminum, as de-

scribed in Sections 2.5.1 and 2.5.2.

Fig. 2.11 shows a schematic survey of the most commonly used aluminum alloys. Table2.2 illustrates the Aluminum Association and American National Standard Institute (ANSI)

Table 2.2: The Aluminum Association alloy designation system

Wrought alloys Series Cast alloys Series

Al (99.00 % miniumum or greater) 1xxx Al (99.00 % miniumum or greater) 1xx.x

Alloys grouped by major alloying elements

Cu 2xxx Cu 2xx.x

Mn 3xxx Si + Cu or Mg 3xx.x

Si 4xxx Si 4xx.x

Mg 5xxx Mg 5xx.x

Mg and Si 6xxx Zn 7xx.x

Zn 7xxx Sn 8xx.x

Other element 8xxx Other element 9xx.x

Unused series 9xxx Unused series 6xx.x

Wrought alloy designations: Four digits are used to identify wrought aluminum and wrought aluminum alloys.

The alloy group is identified by the first digit. Modifications of the original alloy and impurity limits are indicated bythe second digit. In the case of the 1xxx group, the last two digits indicate the minimum aluminum percentage. For

the 2xxx through 8xxx groups, the last two digits serve to further identify individual aluminum alloys. For experi-

mental alloys, the prefix “X” is added, as in a designation (e.g., X2037). When the alloy ceases to be experimental

the prefix is dropped.

Cast alloy designations: The designation system for cast aluminum alloys is similar to that for wrought products,

in that the first digit indicates the major alloy group. Digits two and three indicate the aluminum purity or further

identify the alloy. The digit to the right of the decimal place indicates the product form, either a casting or ingot.

Modifications to original casting alloys are indicated by a serial letter before the numerical designation (e.g., A356.0

or B413.0).


19/19

25

alloy designation system for wrought and cast alloys, described more fully in AppendixC and in full in the Aluminum Association’s Aluminum Standards and Data. There is aninternational accord on wrought alloy designations, recognizing the Aluminum Associa-tion designations virtually worldwide.

There is not an equivalent international accord on cast alloy designations, so there are notexact equivalents for these alloy designations in different countries. For this reason, atvarious places in this book, both the US and international designations for alloys andalloy types are sometimes utilized to help the reader. Similarly, there is no internationalaccord on temper designations (also described in Appendix C), so these too may varyfrom country to country.

2.5.1 Wrought alloys

Strength is increased by the addition of magnesium (up to a maximum of 7%) and also byadditions of zinc, copper, and/or silicon in addition to magnesium. Good high-tempera-ture strength is attained by the addition of copper (up to 4%) and/or nickel, manganese,or iron up to one percent each. Good chemical resistance is shown by alloys with addi-tions of magnesium, manganese, or a combination of magnesium and silicon. Machin-ability is greatly improved by the addition of lead and bismuth up to 0.6% each. Afine-grained structure is obtained especially through the addition of titanium and boron(up to 0.1%). A fine grain upon recrystallization of semifabricated products is often ob-tained through additions of chromium or zirconium (up to approximately 0.1%). Otherelements, for example iron and manganese, have the tendency to act as grain refiners as

well.

2.5.2 Casting alloys

Castability is improved through the addition of silicon up to 13%. Dimensional stabilityupon heating (pistons) is assured by silicon contents up to 25%.

There are also various specialty groups of alloys that make up only a very small part of the total production of aluminum semifabricated products. These are not included in theschematic in Fig. 2.11. Piston alloys and “free-machining” alloys belong to this specialgroup. The latter group includes alloys with lead and other additions that cause the turn-ings to break into small pieces during machining; this is desirable from a fabricatingstandpoint. Having covered the main factors in the production and processing of alumi-num, we turn now to the main theme of this book.

Aluminium Smelting & Production

Documents