Top Banner
1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467 Email: [email protected]
40

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Mar 29, 2015

Download

Documents

Sidney Colliver
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

1

Design and drawing of RC Structures

CV61

Dr. G.S.Suresh

Civil Engineering Department

The National Institute of Engineering

Mysore-570 008

Mob: 9342188467Email: [email protected]

Page 2: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

2

DETAILING OF BEAM &SLAB

Page 3: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

3

Learning out Come

• Review of detailing of beams

• Continuous rectangular beams

• Cantilever rectangular beams

• Flanged beams

• Introduction to detailing of slab

• One way slab

Page 4: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

4

Page 5: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

5

PROBLEM No. 3 Draw the Longitudinal section and two cross sections one near the support and other near the mid span of a RCC continuous beam with the following data:

Clear span of beams = 3m each

Width of beam = 200mm

Overall depth of beam = 300mm

Width in intermediate supports = 200 mm

Main reinforcement = 4 Nos -12 mm diameter bars with 2 bars bent up

Anchor/hanger bars= 2-10 mm diameter

Stirrups = 6 mm diameter @ 300 mm c/c.

Materials : HYSD bars and M20 grade concrete

Page 6: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

6

PROBLEM No. 3

Page 7: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

7

PROBLEM No. 4 A rectangular beam of cross section 300 x 450 mm is supported on 4 columns which are equally spaced at 3m c/c. The columns are of 300 mm x 300 mm in section. The reinforcement consists of 4 bars of a6 mm diameter (+ve reinforcement) at mid span and 4 bars of 16 mm diameter at all supports (-ve reinforcement). Anchor bars consists of a 2-16 mm diameter. Stirrups are of 8 mm diameter 2 legged vertical at 200 c/c throughout. Grade of concrete is M20 and type of steel is Fe 415.

Draw longitudinal section and important cross sections.

Page 8: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

8

PROBLEM No. 4

Page 9: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

9

Page 10: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

10

PROBLEM No. 5 Draw to scale of 1:20 the Longitudinal section and two cross-section of a cantilever beam projecting 3.2 from a support using following data

Clear span =3.2m

Overall depth at free end = 150 mm

Overall depth at fixed end = 450 mm

Width of cantilever beam = 300 mm

Main steel = 4-28 mm dia with two bars curtailed at 1.5m from support

Anchor bars = 2 Nos. 16 mm dia

Nominal stirrups = 6mm dia at 40 mm c/c

Bearing at fixed end = 300 mm

Use M20 concrete and Fe 415 steel

Page 11: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

11

PROBLEM No. 5

Page 12: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

12

PROBLEM No. 6A cantilever beam with 3.2m length is resting over a masonry wall and supporting a slab over it. Draw to a suitable scale Longitudinal section, two cross-sections and sectional plan with the following data:

Size of beam = 300 mm x 350 mm at free end and 300 mm x 450 mm at fixed end and in the wall up to a length of 4.8m

Main steel: 4 nos. of 25 mm dia bars, two bars curtailed at 1.2m from free end

Hanger bars: 2 nos. 16mm.

Stirrups: 6mm dia 2 legged stirrups @ 200 mm c/c the support length and @100 mm c/c from fixed end up to length of 1m @ 150mm c/c up to curtailed bars and remaining @ 200 c/c.

Use M20 concrete and Fe 415 steel

Page 13: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

13

PROBLEM No. 2

Page 14: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

14

Page 15: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

15

PROBLEM No. 7 A beam has following data

Clear span = 4m

Support width = 300mm

Size of web = 350 x 400

Size of flange = 1200 x 120mm

Main reinforcement in two layers : 3-20 tor + 3-16 tor and to be curtailed at a distance 400 mm from inner face of support

Hanger bars: 3- 20 tor

Stirrups: 2L-8 tor @ 200 c/c

Use M20 concrete and Fe 415 steel

Draw longitudinal and cross section if the beam is

1. T-beam

2. Inverted T-beam

3. L-Beam

Page 16: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

16

PROBLEM No. 5

Page 17: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

17

Page 18: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh18

Introduction

• Used for covering spaces in the form of roof or floor

• Slab may be supported on walls or beams or columns .

• Slab supported directly by columns are called flat slab

• One Way Slab • Two Way Slab

Page 19: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh19

Introduction

• Slabs could be simply supported, continuous or cantilever

• In two way slab the corners may be held down by restraints or may be allowed to lift up

• Additional torsion reinforcement is required at corners when it is restrained against uplifting as shown in Fig

Page 20: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh20

Introduction

Page 21: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh21

Introduction• Thickness of the slab is decided based on

span to depth ratio specified in IS456-2000. Min reinforcement is 0.12% for HYSD bars and 0.15 % for mild steel bars.

• The maximum diameter of bar used in slab should not exceed 1/8 of the total thickness of slab

• Maximum spacing of main bar is restricted to 3 times effective depth or 300 mm which ever is less

• For distribution bars the maximum spacing is specified as 5 times the effective depth or 450 mm which ever is less

Page 22: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh22

Introduction• Generally 15 mm to 20 mm cover is

provided for the main reinforcements

• Alternate main bars can be cranked near support or could be bent at 1800 at the edge and then extended at the top inside the slab as shown in Fig

• Curtailment and cranking of bars and is shown in Fig

Page 23: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh23

Introduction

Page 24: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh24

Introduction

• Torsion Reinforcement shall be provided as shown in Fig.

Page 25: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh25

Torsion Reinforcement

Page 26: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh26

Torsion Reinforcement

Page 27: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh27

Typical One Way slab

Page 28: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

Dr.G.S.Suresh28

Typical Two Way slab

Page 29: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

29

PROBLEM Prepare a detailed structural drawing of one way continuous slab for a hall of clear dimensions 7m wide and 11.77 m long, use following data

Centre to centre distance of supporting beams = 3.0 m

Span of the beams = 7.23m

Beams are supported on walls of 0.23 m thickness

C/s of beam = 230 x 450 mm

Grade of concrete : M20

Type of steel : Fe415

Clear cover : 20 mm

Slab thickness: 150 mm

Beam depth is inclusive of slab depth, The hall is having walls on all 4 sides

Page 30: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

30

PROBLEM Main positive reinforcement @ end span = 8mm

diameter @100 c/c

Main reinforcement in other interior panels = 8 mm diameter @ 200 c/c

Negative reinforcement @ all supports = 8mm diameter @ 200 c/c

Distribution steel= 8mm diameter @ 200 c/c

Page 31: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

31

PROBLEM

Page 32: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

32

Page 33: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

33

No. 1

Page 34: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

34

No. 2

Page 35: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

35

No. 3

Page 36: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

36

No. 4

Page 37: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

37

No. 5

Page 38: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

38

Do it Yourself

1. Draw the longitudinal section and typical cross sections ( at centre and support), and show the reinforcement details in a simply supported rectangular beam of size 300 mm x 500 mm, clear span 5m supported on walls of 0.3m, use a suitable scale

Reinforcements:

Main: 4 No. 16mm dia with 2 No. cranked at 1m from centre of support. Stirrup holders 2 Nos. of 12 mm dia

Stirrups: 2 legged 8 mm dia stirrups at 250 mm c/c in the central 2m span and 2 legged 8 mm dia stirrups at 150 mm c/c in the remaining portion. Assume concrete M 20 grade and steel Fe 415, and suitable cover. Prepare the bar bending schedule and calculate quantity of steel and concrete required.

Page 39: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

39

Do it Yourself

2. Prepare the bar bending schedule and estimate quantity of steel and concrete after drawing the longitudinal and cross section. Other details are

Span of beam = 4.2 m

Cross section at support end 300 x 600 mm and cross section at free end 300 x 150 mm

Reinforcements:

Main tension steel: 4-20 mm dia, 2 bars are curtailed at a distance of 2m from free end

Hanger bars: 1-12 mm dia

Two legged stirrups 8mm dia @ 140 mm c/c for full length.

Page 40: 1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore-570 008 Mob: 9342188467.

40

Dr. G.S.Suresh

Civil Engineering Department

The National Institute of Engineering

Mysore-570 008

Mob: 9342188467 Email: [email protected]